Search Results

Search found 4769 results on 191 pages for 'nirmal ram'.

Page 185/191 | < Previous Page | 181 182 183 184 185 186 187 188 189 190 191  | Next Page >

  • Hard drive write speed - finding a lighter antivirus?

    - by Shingetsu
    I recently have been getting a lot of system lag here (for example, the mouse and the display in general take about 15 seconds to react in the worst cases). After a lot of monitoring the resources, I found that the problem mainly happens when too much Disk I/O is being done. Three culprits have been identified: My browser had the highest write I/O with 35,000,000 I/O Write Bytes. Steam had the highest read I/O (when IDLE!!!) with 106,000,000 I/O Read Bytes. My antivirus (in both cases I will soon mention) was the runner up in both cases with: 30,000,000ish write and 80,000,000ish read. The first AV I had was Avast! which I had liked on my previous system. After noticing it taking so much I/O I switched to Panda (supposing it wouldn't use TOO much during idle phase). However it only used a bit less I/O. Just a lot less memory and cpu and somewhat more network. My browser at the moment is Maxthon 3 (which I like a lot). Before this I was running chrome which had similar data and much higher cpu when running in the background was enabled. I'm not going to be running steam all the time and there aren't many alternatives to it. I like my browser very much, but I AM willing to switch if there's an obvious problem (I'm in programming, however I'm not a very good sysadmin, especially not when it comes to windows). Finally, my system almost stops lagging when I turn off the antivirus (and preferably steam) (some remains but once in every 5-6 hours for a few seconds so it isn't a big problem). My question (has a few parts): Is it possible to configure steam to lower it's I/O usage? (and maybe network while we're at it?) Which antivirus (very preferably free) uses lowest I/O while idle (I leave PC alone during active scans so that isn't a problem). Is there an obvious problem with my current browser and, if so, is there a way to fix it or should I switch and, if so, to what? (P.S. I've been on FFox for some time too). Info on system: Windows 7 (32 bit T_T, I am getting a new one in a few months but I want to keep using system during that time though). Hard Drive (main) is a Raid0. (Also have an external 1TB one which contains steam (and steam alone). As such it doesn't get used by much anything other than steam and isn't a very large problem. However steam still uses some I/O of registry) CPU: Intel(R) Core(TM)2 CPU [email protected] RAM: 6GB (3.25GB usable) (this and CPU have little effect as shown in next section) Additional info: Memory usage during problematic times: 44% CPU usage during problematic times: 35% Page File: main drive: system managed. 1TB drive: none. The current system I'm using is about 6 years old and is mainly a place holder while I await the new one in a few months. Final words: this is my 1st post on Super User (this question wouldn't feel right on Stack Overflow where I usually stay). If it doesn't have it's place here please tell me. If anything is wrong with it, same. Edit Technically I'm looking for a live thread detection program with minimal IO usage. I already have good active scan capability: Kaspersky (the free scanner uses the paid database) and MalwareBytes. Edit 2 Noticed another one, it seems that windows media player has been using stuff even when off! Turning it off and restarting now. If the problem is fixed I'll tell you guys. The reason I didn't notice it before was because I didn't have resource manager in front of me at the MOMENT of the problem. Now I did and it was at the very top of the list!

    Read the article

  • An offscreen MKMapView behaves differently in 3.2, 4.0

    - by Duane Fields
    In 3.1 I've been using an "offscreen" MKMapView to create map images that I can rotate, crop and so forth before presenting them the user. In 3.2 and 4.0 this technique no longer works quite right. Here's some code that illustrates the problem, followed by my theory. // create map view _mapView = [[MKMapView alloc] initWithFrame:CGRectMake(0, 0, MAP_FRAME_SIZE, MAP_FRAME_SIZE)]; _mapView.zoomEnabled = NO; _mapView.scrollEnabled = NO; _mapView.delegate = self; _mapView.mapType = MKMapTypeSatellite; // zoom in to something enough to fill the screen MKCoordinateRegion region; CLLocationCoordinate2D center = {30.267222, -97.763889}; region.center = center; MKCoordinateSpan span = {0.1, 0.1 }; region.span = span; _mapView.region = region; // set scrollview content size to full the imageView _scrollView.contentSize = _imageView.frame.size; // force it to load #ifndef __IPHONE_3_2 // in 3.1 we can render to an offscreen context to force a load UIGraphicsBeginImageContext(_mapView.frame.size); [_mapView.layer renderInContext:UIGraphicsGetCurrentContext()]; UIGraphicsEndImageContext(); #else // in 3.2 and above, the renderInContext trick doesn't work... // this at least causes the map to render, but it's clipped to what appears to be // the viewPort size, plus some padding [self.view addSubview:_mapView]; #endif when the map is done loading, I snap picture of it and stuff it in my scrollview - (void)mapViewDidFinishLoadingMap:(MKMapView *)mapView { NSLog(@"[MapBuilder] mapViewDidFinishLoadingMap"); // render the map to a UIImage UIGraphicsBeginImageContext(mapView.bounds.size); // the first sub layer is just the map, the second is the google layer, this sublayer structure might change of course [[[mapView.layer sublayers] objectAtIndex:0] renderInContext:UIGraphicsGetCurrentContext()]; // we are done with the mapView at this point, we need its ram! _mapView.delegate = nil; [_mapView release]; [_mapView removeFromSuperview]; _mapView = nil; UIImage* mapImage = [UIGraphicsGetImageFromCurrentImageContext() retain]; UIGraphicsEndImageContext(); _imageView.image = mapImage; [mapImage release], mapImage = nil; } The first problem is that in 3.1 rendering to a context would trigger the map to begin loading. This no longer works in 3.2, 4.0. The only thing I have found would trigger the load is to temporarily add the map to the view (i.e. make it visible). The problem being that the map only renders to the visible area of the screen, plus a little padding. The frame/bounds are fine, but it appears to be "helpfully" optimizes the loading to limit the tiles to those visible on the screen or close to it. Any ideas how to force the map to load at full size? Anyone else have this issue?

    Read the article

  • Troubleshooting .NET "Fatal Execution Engine Error"

    - by JYelton
    Summary: I periodically get a .NET Fatal Execution Engine Error on an application which I cannot seem to debug. The dialog that comes up only offers to close the program or send information about the error to Microsoft. I've tried looking at the more detailed information but I don't know how to make use of it. Error: The error is visible in Event Viewer under Applications and is as follows: .NET Runtime version 2.0.50727.3607 - Fatal Execution Engine Error (7A09795E) (80131506) The computer running it is Windows XP Professional SP 3. (Intel Core2Quad Q6600 2.4GHz w/ 2.0 GB of RAM) Other .NET-based projects that lack multi-threaded downloading (see below) seem to run just fine. Application: The application is written in C#/.NET 3.5 using VS2008, and installed via a setup project. The app is multi-threaded and downloads data from multiple web servers using System.Net.HttpWebRequest and its methods. I've determined that the .NET error has something to do with either threading or HttpWebRequest but I haven't been able to get any closer as this particular error seems impossible to debug. I've tried handling errors on many levels, including the following in Program.cs: // handle UI thread exceptions Application.ThreadException += new ThreadExceptionEventHandler(Application_ThreadException); // handle non-UI thread exceptions AppDomain.CurrentDomain.UnhandledException += new UnhandledExceptionEventHandler(CurrentDomain_UnhandledException); Application.EnableVisualStyles(); Application.SetCompatibleTextRenderingDefault(false); // force all windows forms errors to go through our handler Application.SetUnhandledExceptionMode(UnhandledExceptionMode.CatchException); More Notes and What I've Tried... Installed Visual Studio 2008 on the target machine and tried running in debug mode, but the error still occurs, with no hint as to where in source code it occurred. When running the program from its installed version (Release) the error occurs more frequently, usually within minutes of launching the application. When running the program in debug mode inside of VS2008, it can run for hours or days before generating the error. Reinstalled .NET 3.5 and made sure all updates are applied. Broke random cubicle objects in frustration. Rewritten parts of code that deal with threading and downloading in attempts to catch and log exceptions, though logging seemed to aggravate the problem (and never provided any data). Question: What steps can I take to troubleshoot or debug this kind of error? Memory dumps and the like seem to be the next step, but I'm not experienced at interpreting them. Perhaps there's something more I can do in the code to try and catch errors... It would be nice if the "Fatal Execution Engine Error" was more informative, but internet searches have only told me that it's a common error for a lot of .NET-related items.

    Read the article

  • Tips / techniques for high-performance C# server sockets

    - by McKenzieG1
    I have a .NET 2.0 server that seems to be running into scaling problems, probably due to poor design of the socket-handling code, and I am looking for guidance on how I might redesign it to improve performance. Usage scenario: 50 - 150 clients, high rate (up to 100s / second) of small messages (10s of bytes each) to / from each client. Client connections are long-lived - typically hours. (The server is part of a trading system. The client messages are aggregated into groups to send to an exchange over a smaller number of 'outbound' socket connections, and acknowledgment messages are sent back to the clients as each group is processed by the exchange.) OS is Windows Server 2003, hardware is 2 x 4-core X5355. Current client socket design: A TcpListener spawns a thread to read each client socket as clients connect. The threads block on Socket.Receive, parsing incoming messages and inserting them into a set of queues for processing by the core server logic. Acknowledgment messages are sent back out over the client sockets using async Socket.BeginSend calls from the threads that talk to the exchange side. Observed problems: As the client count has grown (now 60-70), we have started to see intermittent delays of up to 100s of milliseconds while sending and receiving data to/from the clients. (We log timestamps for each acknowledgment message, and we can see occasional long gaps in the timestamp sequence for bunches of acks from the same group that normally go out in a few ms total.) Overall system CPU usage is low (< 10%), there is plenty of free RAM, and the core logic and the outbound (exchange-facing) side are performing fine, so the problem seems to be isolated to the client-facing socket code. There is ample network bandwidth between the server and clients (gigabit LAN), and we have ruled out network or hardware-layer problems. Any suggestions or pointers to useful resources would be greatly appreciated. If anyone has any diagnostic or debugging tips for figuring out exactly what is going wrong, those would be great as well. Note: I have the MSDN Magazine article Winsock: Get Closer to the Wire with High-Performance Sockets in .NET, and I have glanced at the Kodart "XF.Server" component - it looks sketchy at best.

    Read the article

  • why jQuery.parseJSON is not a function?

    - by Pandiya Chendur
    I use the following jquery statements and i am getting the error, jQuery.parseJSON is not a function my function is, function Iteratejsondata() {var HfJsonValue = { "Table": [{ "Emp_Id": "3", "Identity_No": "", "Emp_Name": "Jerome", "Address": "Madurai", "Date_Of_Birth": "", "Desig_Name": "Supervisior", "Desig_Description": "Supervisior of the Construction", "SalaryBasis": "Monthly", "FixedSalary": "25000.00" }, { "Emp_Id": "4", "Identity_No": "", "Emp_Name": "Mohan", "Address": "Madurai", "Date_Of_Birth": "", "Desig_Name": "Acc ", "Desig_Description": "Accountant", "SalaryBasis": "Monthly", "FixedSalary": "200.00" }, { "Emp_Id": "5", "Identity_No": "", "Emp_Name": "Murugan", "Address": "Madurai", "Date_Of_Birth": "", "Desig_Name": "Mason", "Desig_Description": "Mason", "SalaryBasis": "Weekly", "FixedSalary": "150.00" }, { "Emp_Id": "6", "Identity_No": "", "Emp_Name": "Ram", "Address": "Madurai", "Date_Of_Birth": "", "Desig_Name": "Mason", "Desig_Description": "Mason", "SalaryBasis": "Weekly", "FixedSalary": "120.00" }, { "Emp_Id": "7", "Identity_No": "", "Emp_Name": "Raja", "Address": "Madurai", "Date_Of_Birth": "", "Desig_Name": "Mason", "Desig_Description": "Mason", "SalaryBasis": "Weekly", "FixedSalary": "135.00" }, { "Emp_Id": "8", "Identity_No": "", "Emp_Name": "Raja kumar", "Address": "Madurai", "Date_Of_Birth": "", "Desig_Name": "Mason Helper", "Desig_Description": "Mason Helper", "SalaryBasis": "Weekly", "FixedSalary": "105.00" }, { "Emp_Id": "9", "Identity_No": "", "Emp_Name": "Lakshmi", "Address": "Madurai", "Date_Of_Birth": "", "Desig_Name": "Mason Helper", "Desig_Description": "Mason Helper", "SalaryBasis": "Weekly", "FixedSalary": "100.00" }, { "Emp_Id": "10", "Identity_No": "", "Emp_Name": "Palani", "Address": "Madurai", "Date_Of_Birth": "", "Desig_Name": "Carpenter", "Desig_Description": "Carpenter", "SalaryBasis": "Weekly", "FixedSalary": "200.00" }, { "Emp_Id": "11", "Identity_No": "", "Emp_Name": "Annamalai", "Address": "Madurai", "Date_Of_Birth": "", "Desig_Name": "Carpenter", "Desig_Description": "Carpenter", "SalaryBasis": "Weekly", "FixedSalary": "220.00" }, { "Emp_Id": "12", "Identity_No": "", "Emp_Name": "David", "Address": "Madurai", "Date_Of_Birth": "", "Desig_Name": "Steel Fixer", "Desig_Description": "Steel Fixer", "SalaryBasis": "Weekly", "FixedSalary": "220.00" }, { "Emp_Id": "13", "Identity_No": "", "Emp_Name": "Chandru", "Address": "Madurai", "Date_Of_Birth": "", "Desig_Name": "Steel Fixer", "Desig_Description": "Steel Fixer", "SalaryBasis": "Weekly", "FixedSalary": "220.00" }, { "Emp_Id": "14", "Identity_No": "", "Emp_Name": "Mani", "Address": "Madurai", "Date_Of_Birth": "", "Desig_Name": "Steel Helper", "Desig_Description": "Steel Helper", "SalaryBasis": "Weekly", "FixedSalary": "175.00" }, { "Emp_Id": "15", "Identity_No": "", "Emp_Name": "Karthik", "Address": "Madurai", "Date_Of_Birth": "", "Desig_Name": "Wood Fixer", "Desig_Description": "Wood Fixer", "SalaryBasis": "Weekly", "FixedSalary": "195.00" }, { "Emp_Id": "16", "Identity_No": "", "Emp_Name": "Bala", "Address": "Madurai", "Date_Of_Birth": "", "Desig_Name": "Wood Fixer", "Desig_Description": "Wood Fixer", "SalaryBasis": "Weekly", "FixedSalary": "185.00" }, { "Emp_Id": "17", "Identity_No": "", "Emp_Name": "Tamil arasi", "Address": "Madurai", "Date_Of_Birth": "", "Desig_Name": "Wood Helper", "Desig_Description": "Wood Helper", "SalaryBasis": "Weekly", "FixedSalary": "185.00" }, { "Emp_Id": "18", "Identity_No": "", "Emp_Name": "Perumal", "Address": "Madurai", "Date_Of_Birth": "", "Desig_Name": "Cook", "Desig_Description": "Cook", "SalaryBasis": "Weekly", "FixedSalary": "105.00" }, { "Emp_Id": "19", "Identity_No": "", "Emp_Name": "Andiappan", "Address": "Madurai", "Date_Of_Birth": "", "Desig_Name": "Watchman", "Desig_Description": "Watchman", "SalaryBasis": "Weekly", "FixedSalary": "150.00"}] }; //var jsonObj = eval('(' + HfJsonValue + ')'); var jsonObj = jQuery.parseJSON(HfJsonValue); and my page looks like this <div id="Pagination" class="page-numbers"></div> <br style="clear:both;" /> <div id="Searchresult"></div> <div id="hiddenresult" style="display:none;"> </div> <script type="text/javascript"> var pagination_options = { num_edge_entries: 2, num_display_entries: 8, callback: pageselectCallback, items_per_page: 3 } function pageselectCallback(page_index, jq) { var items_per_page = pagination_options.items_per_page; var offset = page_index * items_per_page; var new_content = $('#hiddenresult div.resultsdiv').slice(offset, offset + items_per_page).clone(); $('#Searchresult').empty().append(new_content); return false; } function initPagination() { var num_entries = $('#hiddenresult div.resultsdiv').length; // Create pagination element $("#Pagination").pagination(num_entries, pagination_options); } $(document).ready(function() { Iteratejsondata(); initPagination(); }); </script> I ve inspected through firebug and saw all jquery files have been downloaded but why this is hapenning? Any suggestion....

    Read the article

  • Python Memory leak - Solved, but still puzzled

    - by disappearedng
    Dear everyone, I have successfully debugged my own memory leak problems. However, I have noticed some very strange occurence. for fid, fv in freqDic.iteritems(): outf.write(fid+"\t") #ID for i, term in enumerate(domain): #Vector tfidf = self.tf(term, fv) * self.idf( term, docFreqDic) if i == len(domain) - 1: outf.write("%f\n" % tfidf) else: outf.write("%f\t" % tfidf) outf.flush() print "Memory increased by", int(self.memory_mon.usage()) - startMemory outf.close() def tf(self, term, freqVector): total = freqVector[TOTAL] if total == 0: return 0 if term not in freqVector: ## When you don't have these lines memory leaks occurs return 0 ## return float(freqVector[term]) / freqVector[TOTAL] def idf(self, term, docFrequencyPerTerm): if term not in docFrequencyPerTerm: return 0 return math.log( float(docFrequencyPerTerm[TOTAL])/docFrequencyPerTerm[term]) Basically let me describe my problem: 1) I am doing tfidf calculations 2) I traced that the source of memory leaks is coming from defaultdict. 3) I am using the memory_mon from http://stackoverflow.com/questions/276052/how-to-get-current-cpu-and-ram-usage-in-python 4) The reason for my memory leaks is as follows: a) in self.tf, if the lines: if term not in freqVector: return 0 are not added that will cause the memory leak. (I verified this myself using memory_mon and noticed a sharp increase in memory that kept on increasing) The solution to my problem was 1) since fv is a defaultdict, any reference to it that are not found in fv will create an entry. Over a very large domain, this will cause memory leaks. I decided to use dict instead of default dict and the memory problem did go away. My only puzzle is: since fv is created in "for fid, fv in freqDic.iteritems():" shouldn't fv be destroyed at the end of every for loop? I tried putting gc.collect() at the end of the for loop but gc was not able to collect everything (returns 0). Yes, the hypothesis is right, but the memory should stay fairly consistent with ever for loop if for loops do destroy all temp variables. This is what it looks like with that two line in self.tf: Memory increased by 12 Memory increased by 948 Memory increased by 28 Memory increased by 36 Memory increased by 36 Memory increased by 32 Memory increased by 28 Memory increased by 32 Memory increased by 32 Memory increased by 32 Memory increased by 40 Memory increased by 32 Memory increased by 32 Memory increased by 28 and without the the two line: Memory increased by 1652 Memory increased by 3576 Memory increased by 4220 Memory increased by 5760 Memory increased by 7296 Memory increased by 8840 Memory increased by 10456 Memory increased by 12824 Memory increased by 13460 Memory increased by 15000 Memory increased by 17448 Memory increased by 18084 Memory increased by 19628 Memory increased by 22080 Memory increased by 22708 Memory increased by 24248 Memory increased by 26704 Memory increased by 27332 Memory increased by 28864 Memory increased by 30404 Memory increased by 32856 Memory increased by 33552 Memory increased by 35024 Memory increased by 36564 Memory increased by 39016 Memory increased by 39924 Memory increased by 42104 Memory increased by 42724 Memory increased by 44268 Memory increased by 46720 Memory increased by 47352 Memory increased by 48952 Memory increased by 50428 Memory increased by 51964 Memory increased by 53508 Memory increased by 55960 Memory increased by 56584 Memory increased by 58404 Memory increased by 59668 Memory increased by 61208 Memory increased by 62744 Memory increased by 64400 I look forward to your answer

    Read the article

  • Very slow compile times on Visual Studio

    - by johnc
    We are getting very slow compile times, which can take upwards of 20+ minutes on dual core 2GHz, 2G Ram machines. A lot of this is due to the size of our solution which has grown to 70+ projects, as well as VSS which is a bottle neck in itself when you have a lot of files. (swapping out VSS is not an option unfortunately, so I don't want this to descend into a VSS bash) We are looking at combing projects (not nice, as we like the separation of concerns, but is a good opportunity to refactor away some dead wood). We are also looking at having multiple solutions to achieve greater separation of concerns and quicker compile times for each element of the application. This I can see will become a dll hell as we try to keep things in synch. I am interested to know how other teams have dealt with this scaling issue, what do you do when your code base reaches a critical mass that you are wasting half the day watching the status bar deliver compile messages UPDATE Apologies, I neglected to mention this is a C# solution. Thanks for all the cpp suggestions, but it's been a few years since I've had to worry about headers. At a distance I say I miss C++, but I'm not sure I want to go back EDIT: Nice suggestions that have helped so far (not saying there aren't other nice suggestions below, just what has helped) New 3GHz laptop - the power of lost utilization works wonders when whinging to management Disable Anti Virus during compile 'Disconnecting' from VSS (actually the network) during compile - I may get us to remove VS-VSS integration altogether and stick to using the VSS UI Still not rip-snorting through a compile, but every bit helps. Orion did mention in a comment that generics may have a play also. From my tests there does appear to be a minimal performance hit, but not high enough to sure - compile times can be inconsistent due to disc activity. Due to time limitations, my tests didn't include as many Generics, or as much code, as would appear in live system, so that may accumulate. I wouldn't avoid using generics where they are supposed to be used, just for compile time performance WORKAROUND We are testing the practice of building new areas of the application in new solutions, importing in the latest dlls as required, them integrating them into the larger solution when we are happy with them. We may also do them same to existing code by creating temporary solutions that just encapsulate the areas we need to work on, and throwing them away after reintegrating the code. We need to weigh up the time it will take to reintegrate this code against the time we gain by not having Rip Van Winkle like experiences with rapid recompiling during development.

    Read the article

  • Android: OutofMemoryError: bitmap size exceeds VM budget with no reason I can see.

    - by Meymann
    Hi. I am having an OutOfMemory exception with a gallery over 600x800 pixels JPEG's. The environment I've been using Gallery with JPG images around 600x800 pixels. Since my content may be a bit more complex than just images, I have set each view to be a RelativeLayout that wraps ImageView with the JPG. In order to "speed up" the user experience I have a simple cache of 4 slots that prefetches (in a looper) about 1 image left and 1 image right to the displayed image and keeps them in a 4 slot HashMap. The platform I am using AVD of 256 RAM and 128 Heap Size, with a 600x800 screen. It also happens on an Entourage Edge target, except that with the device it's harder to debug. The problem I have been getting an exception: OutofMemoryError: bitmap size exceeds VM budget And it happens when fetching the fifth image. I have tried to change the size of my image cache, and it is still the same. The strange thing: There should not be a memory problem In order to make sure the heap limit is very far away from what I need, I have defined a dummy 8MB array in the beginning, and left it unreferenced so it's immediately dispatched. It is a member of the activity thread and is defined as following static { @SuppressWarnings("unused") byte dummy[] = new byte[ 8*1024*1024 ]; } The result is that the heap size is nearly 11MB and it's all free. Note I have added that trick after it began to crash. It makes OutOfMemory less frequent. Now, I am using DDMS. Just before the crash (does not change much after the crash), DDMS shows: ID Heap Size Allocated Free %Used #Objects 1 11.195 MB 2.428 MB 8.767 MB 21.69% 47,156 And in the detail table it shows: Type Count Total Size Smallest Largest Median Average free 1,536 8.739MB 16B 7.750MB 24B 5.825KB The largest block is 7.7MB. And yet the LogCat says: ERROR/dalvikvm-heap(1923): 925200-byte external allocation too large for this process. If you mind the relation of the median and the average, it is plausible to assume that most of the available blocks are very small. However, there is a block large enough for the bitmap, it's 7.7M. How come it is still not enough? Note: I recorded a heap trace. When looking at the amount of data allocated, it does not feel like more than 2M is allocated. It does match the free memory report by DDMS. Could it be that I experience some problem like heap-fragmentation? How do I solve/workaround the problem? Is the heap shared to all threads? Could it be that I interpret the DDMS readout in a wrong way, and there is really no 900K block to allocate? If so, can anybody please tell me where I can see that? Thanks a lot Meymann

    Read the article

  • Paging through records (json data) using jQuery...

    - by Pandiya Chendur
    I have a JSON result that contains numerous records. I'd like to show the first five records in one page and create pager links which have to move to that page with five record so on. I don't want the page to refresh which is why I'm hoping for a combination of JavaScript and jQuery. My json data looks like this: {"Table" : [ {"Emp_Id" : "3","Identity_No" : "","Emp_Name" : "Jerome","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Supervisior","Desig_Description" : "Supervisior of the Construction","SalaryBasis" : "Monthly","FixedSalary" : "25000.00"}, {"Emp_Id" : "4","Identity_No" : "","Emp_Name" : "Mohan","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Acc ","Desig_Description" : "Accountant","SalaryBasis" : "Monthly","FixedSalary" : "200.00"}, {"Emp_Id" : "5","Identity_No" : "","Emp_Name" : "Murugan","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Mason","Desig_Description" : "Mason","SalaryBasis" : "Weekly","FixedSalary" : "150.00"}, {"Emp_Id" : "6","Identity_No" : "","Emp_Name" : "Ram","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Mason","Desig_Description" : "Mason","SalaryBasis" : "Weekly","FixedSalary" : "120.00"}, {"Emp_Id" : "7","Identity_No" : "","Emp_Name" : "Raja","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Mason","Desig_Description" : "Mason","SalaryBasis" : "Weekly","FixedSalary" : "135.00"}, {"Emp_Id" : "8","Identity_No" : "","Emp_Name" : "Raja kumar","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Mason Helper","Desig_Description" : "Mason Helper","SalaryBasis" : "Weekly","FixedSalary" : "105.00"}, {"Emp_Id" : "9","Identity_No" : "","Emp_Name" : "Lakshmi","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Mason Helper","Desig_Description" : "Mason Helper","SalaryBasis" : "Weekly","FixedSalary" : "100.00"}, {"Emp_Id" : "10","Identity_No" : "","Emp_Name" : "Palani","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Carpenter","Desig_Description" : "Carpenter","SalaryBasis" : "Weekly","FixedSalary" : "200.00"}, {"Emp_Id" : "11","Identity_No" : "","Emp_Name" : "Annamalai","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Carpenter","Desig_Description" : "Carpenter","SalaryBasis" : "Weekly","FixedSalary" : "220.00"}, {"Emp_Id" : "12","Identity_No" : "","Emp_Name" : "David","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Steel Fixer","Desig_Description" : "Steel Fixer","SalaryBasis" : "Weekly","FixedSalary" : "220.00"}, {"Emp_Id" : "13","Identity_No" : "","Emp_Name" : "Chandru","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Steel Fixer","Desig_Description" : "Steel Fixer","SalaryBasis" : "Weekly","FixedSalary" : "220.00"}, {"Emp_Id" : "14","Identity_No" : "","Emp_Name" : "Mani","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Steel Helper","Desig_Description" : "Steel Helper","SalaryBasis" : "Weekly","FixedSalary" : "175.00"}, {"Emp_Id" : "15","Identity_No" : "","Emp_Name" : "Karthik","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Wood Fixer","Desig_Description" : "Wood Fixer","SalaryBasis" : "Weekly","FixedSalary" : "195.00"}, {"Emp_Id" : "16","Identity_No" : "","Emp_Name" : "Bala","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Wood Fixer","Desig_Description" : "Wood Fixer","SalaryBasis" : "Weekly","FixedSalary" : "185.00"}, {"Emp_Id" : "17","Identity_No" : "","Emp_Name" : "Tamil arasi","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Wood Helper","Desig_Description" : "Wood Helper","SalaryBasis" : "Weekly","FixedSalary" : "185.00"}, {"Emp_Id" : "18","Identity_No" : "","Emp_Name" : "Perumal","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Cook","Desig_Description" : "Cook","SalaryBasis" : "Weekly","FixedSalary" : "105.00"}, {"Emp_Id" : "19","Identity_No" : "","Emp_Name" : "Andiappan","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Watchman","Desig_Description" : "Watchman","SalaryBasis" : "Weekly","FixedSalary" : "150.00"} ] } And as of now my result looks like this, http://img401.imageshack.us/img401/2500/yuidtsum.jpg I have used jQuery for this: var jsonObj = JSON.parse(HfJsonValue); for (var i = jsonObj.Table.length - 1; i >= 0; i--) { var employee = jsonObj.Table[i]; $('<div class="resultsdiv"><br /><span class="resultName">' + employee.Emp_Name + '</span><span class="resultfields" style="padding-left:100px;">Category&nbsp;:</span>&nbsp;<span class="resultfieldvalues">' + employee.Desig_Name + '</span><br /><br /><span id="SalaryBasis" class="resultfields">Salary Basis&nbsp;:</span>&nbsp;<span class="resultfieldvalues">' + employee.SalaryBasis + '</span><span class="resultfields" style="padding-left:25px;">Salary&nbsp;:</span>&nbsp;<span class="resultfieldvalues">' + employee.FixedSalary + '</span><span style="font-size:110%;font-weight:bolder;padding-left:25px;">Address&nbsp;:</span>&nbsp;<span class="resultfieldvalues">' + employee.Address + '</span></div>') .insertAfter('#ResultsDiv'); } My image contains only 6 records as of now. Any suggestions?

    Read the article

  • What are the reasons why the CPU usage doesn’t go 100% with C# and APM?

    - by Martin
    I have an application which is CPU intensive. When the data is processed on a single thread, the CPU usage goes to 100% for many minutes. So the performance of the application appears to be bound by the CPU. I have multithreaded the logic of the application, which result in an increase of the overall performance. However, the CPU usage hardly goes above 30%-50%. I would expect the CPU (and the many cores) to go to 100% since I process many set of data at the same time. Below is a simplified example of the logic I use to start the threads. When I run this example, the CPU goes to 100% (on an 8/16 cores machine). However, my application which uses the same pattern doesn’t. public class DataExecutionContext { public int Counter { get; set; } // Arrays of data } static void Main(string[] args) { // Load data from the database into the context var contexts = new List<DataExecutionContext>(100); for (int i = 0; i < 100; i++) { contexts.Add(new DataExecutionContext()); } // Data loaded. Start to process. var latch = new CountdownEvent(contexts.Count); var processData = new Action<DataExecutionContext>(c => { // The thread doesn't access data from a DB, file, // network, etc. It reads and write data in RAM only // (in its context). for (int i = 0; i < 100000000; i++) c.Counter++; }); foreach (var context in contexts) { processData.BeginInvoke(context, new AsyncCallback(ar => { latch.Signal(); }), null); } latch.Wait(); } I have reduced the number of locks to the strict minimum (only the latch is locking). The best way I found was to create a context in which a thread can read/write in memory. Contexts are not shared among other threads. The threads can’t access the database, files or network. In other words, I profiled my application and I didn’t find any bottleneck. Why the CPU usage of my application doesn’t go about 50%? Is it the pattern I use? Should I create my own thread instead of using the .Net thread pool? Is there any gotchas? Is there any tool that you could recommend me to find my issue? Thanks!

    Read the article

  • mysql never releases memory

    - by Ishu
    I have a production server clocking about 4 million page views per month. The server has got 8GB of RAM and mysql acts as a database. I am facing problems in handling mysql to take this load. I need to restart mysql twice a day to handle this thing. The problem with mysql is that it starts with some particular occupation, the memory consumed by mysql keeps on increasing untill it reaches the maximum it can consume and then mysql stops responding slowly or does not respond at all, which freezes the server. All my tables are indexed properly and there are no long queries. I need some one to help on how to go about debugging what to do here. All my tables are myisam. I have tried configuring the parameters key_buffer etc but to no rescue. Any sort of help is greatly appreciated. Here are some parameters which may help. mysql --version mysql Ver 14.12 Distrib 5.0.77, for redhat-linux-gnu (i686) using readline 5.1 mysql> show variables; +---------------------------------+------------------------------------------------------------+ | Variable_name | Value | +---------------------------------+------------------------------------------------------------+ | auto_increment_increment | 1 | | auto_increment_offset | 1 | | automatic_sp_privileges | ON | | back_log | 50 | | basedir | /usr/ | | bdb_cache_size | 8384512 | | bdb_home | /var/lib/mysql/ | | bdb_log_buffer_size | 262144 | | bdb_logdir | | | bdb_max_lock | 10000 | | bdb_shared_data | OFF | | bdb_tmpdir | /tmp/ | | binlog_cache_size | 32768 | | bulk_insert_buffer_size | 8388608 | | character_set_client | latin1 | | character_set_connection | latin1 | | character_set_database | latin1 | | character_set_filesystem | binary | | character_set_results | latin1 | | character_set_server | latin1 | | character_set_system | utf8 | | character_sets_dir | /usr/share/mysql/charsets/ | | collation_connection | latin1_swedish_ci | | collation_database | latin1_swedish_ci | | collation_server | latin1_swedish_ci | | completion_type | 0 | | concurrent_insert | 1 | | connect_timeout | 10 | | datadir | /var/lib/mysql/ | | date_format | %Y-%m-%d | | datetime_format | %Y-%m-%d %H:%i:%s | | default_week_format | 0 | | delay_key_write | ON | | delayed_insert_limit | 100 | | delayed_insert_timeout | 300 | | delayed_queue_size | 1000 | | div_precision_increment | 4 | | keep_files_on_create | OFF | | engine_condition_pushdown | OFF | | expire_logs_days | 0 | | flush | OFF | | flush_time | 0 | | ft_boolean_syntax | + -><()~*:""&| | | ft_max_word_len | 84 | | ft_min_word_len | 4 | | ft_query_expansion_limit | 20 | | ft_stopword_file | (built-in) | | group_concat_max_len | 1024 | | have_archive | NO | | have_bdb | YES | | have_blackhole_engine | NO | | have_compress | YES | | have_crypt | YES | | have_csv | NO | | have_dynamic_loading | YES | | have_example_engine | NO | | have_federated_engine | NO | | have_geometry | YES | | have_innodb | YES | | have_isam | NO | | have_merge_engine | YES | | have_ndbcluster | NO | | have_openssl | DISABLED | | have_ssl | DISABLED | | have_query_cache | YES | | have_raid | NO | | have_rtree_keys | YES | | have_symlink | YES | | | init_connect | | | init_file | | | init_slave | | | interactive_timeout | 28800 | | join_buffer_size | 131072 | | key_buffer_size | 2621440000 | | key_cache_age_threshold | 300 | | key_cache_block_size | 1024 | | key_cache_division_limit | 100 | | language | /usr/share/mysql/english/ | | large_files_support | ON | | large_page_size | 0 | | large_pages | OFF | | lc_time_names | en_US | | license | GPL | | local_infile | ON | | locked_in_memory | OFF | | log | OFF | | log_bin | ON | | log_bin_trust_function_creators | OFF | | log_error | | | log_queries_not_using_indexes | OFF | | log_slave_updates | OFF | | log_slow_queries | ON | | log_warnings | 1 | | long_query_time | 8 | | low_priority_updates | OFF | | lower_case_file_system | OFF | | lower_case_table_names | 0 | | max_allowed_packet | 8388608 | | max_binlog_cache_size | 4294963200 | | max_binlog_size | 1073741824 | | max_connect_errors | 10 | | max_connections | 400 | | max_delayed_threads | 20 | | max_error_count | 64 | | max_heap_table_size | 16777216 | | max_insert_delayed_threads | 20 | | max_join_size | 4294967295 | | max_length_for_sort_data | 1024 | | max_prepared_stmt_count | 16382 | | max_relay_log_size | 0 | | max_seeks_for_key | 4294967295 | | max_sort_length | 1024 | | max_sp_recursion_depth | 0 | | max_tmp_tables | 32 | | max_user_connections | 0 | | max_write_lock_count | 4294967295 | | multi_range_count | 256 | | myisam_data_pointer_size | 6 | | myisam_max_sort_file_size | 2146435072 | | myisam_recover_options | OFF | | myisam_repair_threads | 1 | | myisam_sort_buffer_size | 16777216 | | myisam_stats_method | nulls_unequal | | net_buffer_length | 16384 | | net_read_timeout | 30 | | net_retry_count | 10 | | net_write_timeout | 60 | | new | OFF | | old_passwords | OFF | | open_files_limit | 2000 | | optimizer_prune_level | 1 | | optimizer_search_depth | 62 | | pid_file | /var/run/mysqld/mysqld.pid | | plugin_dir | | | port | 3306 | | preload_buffer_size | 32768 | | profiling | OFF | | profiling_history_size | 15 | | protocol_version | 10 | | query_alloc_block_size | 8192 | | query_cache_limit | 1048576 | | query_cache_min_res_unit | 4096 | | query_cache_size | 134217728 | | query_cache_type | ON | | query_cache_wlock_invalidate | OFF | | query_prealloc_size | 8192 | | range_alloc_block_size | 4096 | | read_buffer_size | 2097152 | | read_only | OFF | | read_rnd_buffer_size | 8388608 | | relay_log | | | relay_log_index | | | relay_log_info_file | relay-log.info | | relay_log_purge | ON | | relay_log_space_limit | 0 | | rpl_recovery_rank | 0 | | secure_auth | OFF | | secure_file_priv | | | server_id | 1 | | skip_external_locking | ON | | skip_networking | OFF | | skip_show_database | OFF | | slave_compressed_protocol | OFF | | slave_load_tmpdir | /tmp/ | | slave_net_timeout | 3600 | | slave_skip_errors | OFF | | slave_transaction_retries | 10 | | slow_launch_time | 2 | | socket | /var/lib/mysql/mysql.sock | | sort_buffer_size | 2097152 | | sql_big_selects | ON | | sql_mode | | | sql_notes | ON | | sql_warnings | OFF | | ssl_ca | | | ssl_capath | | | ssl_cert | | | ssl_cipher | | | ssl_key | | | storage_engine | MyISAM | | sync_binlog | 0 | | sync_frm | ON | | system_time_zone | CST | | table_cache | 256 | | table_lock_wait_timeout | 50 | | table_type | MyISAM | | thread_cache_size | 8 | | thread_stack | 196608 | | time_format | %H:%i:%s | | time_zone | SYSTEM | | timed_mutexes | OFF | | tmp_table_size | 33554432 | | tmpdir | /tmp/ | | transaction_alloc_block_size | 8192 | | transaction_prealloc_size | 4096 | | tx_isolation | REPEATABLE-READ | | updatable_views_with_limit | YES | | version | 5.0.77-log | | version_bdb | Sleepycat Software: Berkeley DB 4.1.24: (January 29, 2009) | | version_comment | Source distribution | | version_compile_machine | i686 | | version_compile_os | redhat-linux-gnu | | wait_timeout | 28800 | +---------------------------------+------------------------------------------------------------+

    Read the article

  • Team Foundation Server Setup/Access

    - by Angel Brighteyes
    What I need: A TFS 2010 Setup that allows 2 application developers to access the TFS from remote locations. How it is setup: Server 2008 Standard 2g Ram 300g HD space SharePoint Server 2007, using SQL Server 2005 SQL Server 2008 Standard Team Foundation Server 2010 IIS 7 Sharepoint Bindings: TFS.DynAccount.Me:80; TFS:80 TFS Bindings: TFS.DynAccount.Me:8080; TFS:8080 Using DynDNS service to account for the dynamic ip address being used, this is a requirement for the moment until I can get a better isp package. Access using Local Accounts Server is not setup on a domain, or as a domain. Consequently I did not setup AD services. Problem: When logged into TFS using my credentials TFS\AdminUser through the DynDNS account TFS.DynAccount.Me I recieve the 'Red X of Death' on the Documents and Reports folder. When logged into the TFS through the local peer to peer network using the same credentials TFS\AdminUser I do not receive the 'Red X of Death' problem. Further Troubleshooting: When users 'Right Click' the 'TeamProject1' Click 'Show Project Portal' it tries to take them to http://TFS:8080 instead of http://TFS.DynAccount.Me:8080, which doing further research I am assuming that it is because team foundation server was setup with a local name of TFS instead of 'TFS.DynAccount.Me' as specified here in Visual Studio Magazines: The Red X of Death. Users can Access the Team Portal for SharePoint via http://TFS.DynAccount.Me/TeamCollection/TeamProject so it is not like we are dead in the water or anything. However, as most employees/staff are prone to do, they have expressed a great distaste for having to do it this way and just be patient until the current project is finished since we are under a very strict deadline. Is there a way to set this up differently, or change some settings someplace, reinstall it, point a CName record for our domain website to the DynAccount (e.g. TFS.OurDomain.com points to TFS.DynAccount.Me, which consequently does allow access to the http site without issues), or something. I really don't feel like after all the time and effort I have spent into, first the cost, second the bloody install, third learning SharePoint well enough, fourth the hours into days spent on this, fifth more troubleshooting, sixth employee headaches to just let it lay where it is at. I figure in my spare/off time I would keep trying to get this to work. So I really appreciate any help any one can give me. I know this is probably something really stupid simple that I will 'Face Palm' over, but at the moment the stress and frustration just has me beat. Thank you again, this community has always been a great help.

    Read the article

  • Problem in linking an nasm code

    - by Stefano
    I'm using a computer with an Intel Core 2 CPU and 2GB of RAM. The SO is Ubuntu 9.04. When I try to compile this code: ;programma per la simulazione di un terminale su PC, ottenuto utilizzando l'8250 ;in condizione di loopback , cioè Tx=Rx section .code64 section .data TXDATA EQU 03F8H ;TRASMETTITORE RXDATA EQU 03F8H ;RICEVITORE BAUDLSB EQU 03F8H ;DIVISORE DI BAUD RATE IN LSB BAUDMSB EQU 03F9H ;DIVISORE DI BAUD RATE IN MSB INTENABLE EQU 03F9H ;REGISTRO DI ABILITAZIONE DELL'INTERRUZIONE INTIDENTIF EQU 03FAH ;REGISTRO DI IDENTIFICAZIONE DELL'INTERRUZIONE LINECTRL EQU 03FBH ;REGISTRO DI CONTROLLO DELLA LINEA MODEMCTRL EQU 03FCH ;REGISTRO DI CONTROLLO DEL MODEM LINESTATUS EQU 03FDH ;REGISTRO DI STATO DELLA LINEA MODEMSTATUS EQU 03FEH ;REGISTRO DI STATO DEL MODEM BAUDRATEDIV DW 0060H ;DIVISOR: LOW=60, HIGH=00 -BAUD =9600 COUNTERCHAR DB 0 ;CHARACTER COUNTER ;DW 256 DUP (?) section .text global _start _start: ;PROGRAMMAZIONE 8250 MOV DX,LINECTRL MOV AL,80H ;BIT 7=1 PER INDIRIZZARE IL BAUD RATE OUT DX,AL MOV DX,BAUDLSB MOV AX,BAUDRATEDIV ;DEFINISCO FATTORE DI DIVISIONE OUT DX,AL MOV DX,BAUDMSB MOV AL,AH OUT DX,AL ;MSB MOV DX,LINECTRL MOV AL,00000011B ;8 BIT DATO, 1 STOP, PARITA' NO OUT DX,AL MOV DX,MODEMCTRL MOV AL,00010011B ;BIT 4=0 PER NO LOOPBACK OUT DX,AL MOV DX,INTENABLE XOR AL,AL ;DISABILITO TUTTI GLI INTERRUPTS OUT DX,AL CICLO: MOV DX,LINESTATUS IN AL,DX ;LEGGO IL REGISTRO DI STATO DELLA LINEA TEST AL,00011110B ;VERIFICO GLI ERRORI (4 TIPI) JNE ERRORI TEST AL,01H ;VERIFICO Rx PRONTO JNE LEGGOCHAR TEST AL,20H ;VERIFICO Tx VUOTO JE CICLO ;SE SI ARRIVA A QUESTO PUNTO ALLORA L'8250 è PRONTO PER TRASMETTERE UN NUOVO CARATTERE MOV AH,1 INT 80H JE CICLO ;SE SI ARRIVA A QUESTO PUNTO SIGNIFICA CHE ESISTE UN CARATTERE DA TASTIERA MOV AH,0 INT 80H ;Al CONTIENE IL CARATTERE DELLA TASTIERA MOV DX,3F8H OUT DX,AL JMP CICLO LEGGOCHAR: MOV AL,[COUNTERCHAR] INC AL CMP AL,15 JE FINE MOV [COUNTERCHAR],AL MOV DX,TXDATA IN AL,DX ;AL CONTIENE IL CARATTERE RICEVUTO AND AL,7FH ;POICHè VI SONO 7 BIT DI DATO ;VISUALIZZAZIONE DEL CARATTERE MOV BX,0 MOV AH,14 INT 80H POP AX CMP AL,0DH ;CONTROLLO SE RETURN JNE CICLO ;CAMBIO RIGA DI VISUALIZZAZIONE MOV AL,0AH MOV BX,0 MOV AH,14 ;INT 10H INT 80H JMP CICLO ;GESTIONE ERRORI ERRORI: MOV DX,3F8H IN AL,DX MOV AL,'?' MOV BX,0 MOV AH,14 INT 80H JMP CICLO FINE: XOR AH,AH MOV AL,03 INT 80H When I compile this code "NASM -f bin UARTLOOP.asm", the compiler can create the UARTLOOP.o file without any error. When I try to link the .o file with "ld UARTLOOP.o" it tells: UARTLOOP.o: In function `_start': UARTLOOP.asm:(.text+0xd): relocation truncated to fit: R_X86_64_16 against `.data' Have u got some ideas to solve this problem? Thx =)

    Read the article

  • Paging Through Records(json data) Using jQuery...

    - by Pandiya Chendur
    I have a JSON result that contains numerous records. I'd like to show the first five records in one page and create pager links which have to move to that page with five record so on. I don't want the page to refresh which is why I'm hoping a combination of JavaScript and jQuery... My json Data looks like this... {"Table" : [{"Emp_Id" : "3","Identity_No" : "","Emp_Name" : "Jerome","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Supervisior","Desig_Description" : "Supervisior of the Construction","SalaryBasis" : "Monthly","FixedSalary" : "25000.00"},{"Emp_Id" : "4","Identity_No" : "","Emp_Name" : "Mohan","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Acc ","Desig_Description" : "Accountant","SalaryBasis" : "Monthly","FixedSalary" : "200.00"},{"Emp_Id" : "5","Identity_No" : "","Emp_Name" : "Murugan","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Mason","Desig_Description" : "Mason","SalaryBasis" : "Weekly","FixedSalary" : "150.00"},{"Emp_Id" : "6","Identity_No" : "","Emp_Name" : "Ram","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Mason","Desig_Description" : "Mason","SalaryBasis" : "Weekly","FixedSalary" : "120.00"},{"Emp_Id" : "7","Identity_No" : "","Emp_Name" : "Raja","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Mason","Desig_Description" : "Mason","SalaryBasis" : "Weekly","FixedSalary" : "135.00"},{"Emp_Id" : "8","Identity_No" : "","Emp_Name" : "Raja kumar","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Mason Helper","Desig_Description" : "Mason Helper","SalaryBasis" : "Weekly","FixedSalary" : "105.00"},{"Emp_Id" : "9","Identity_No" : "","Emp_Name" : "Lakshmi","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Mason Helper","Desig_Description" : "Mason Helper","SalaryBasis" : "Weekly","FixedSalary" : "100.00"},{"Emp_Id" : "10","Identity_No" : "","Emp_Name" : "Palani","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Carpenter","Desig_Description" : "Carpenter","SalaryBasis" : "Weekly","FixedSalary" : "200.00"},{"Emp_Id" : "11","Identity_No" : "","Emp_Name" : "Annamalai","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Carpenter","Desig_Description" : "Carpenter","SalaryBasis" : "Weekly","FixedSalary" : "220.00"},{"Emp_Id" : "12","Identity_No" : "","Emp_Name" : "David","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Steel Fixer","Desig_Description" : "Steel Fixer","SalaryBasis" : "Weekly","FixedSalary" : "220.00"},{"Emp_Id" : "13","Identity_No" : "","Emp_Name" : "Chandru","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Steel Fixer","Desig_Description" : "Steel Fixer","SalaryBasis" : "Weekly","FixedSalary" : "220.00"},{"Emp_Id" : "14","Identity_No" : "","Emp_Name" : "Mani","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Steel Helper","Desig_Description" : "Steel Helper","SalaryBasis" : "Weekly","FixedSalary" : "175.00"},{"Emp_Id" : "15","Identity_No" : "","Emp_Name" : "Karthik","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Wood Fixer","Desig_Description" : "Wood Fixer","SalaryBasis" : "Weekly","FixedSalary" : "195.00"},{"Emp_Id" : "16","Identity_No" : "","Emp_Name" : "Bala","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Wood Fixer","Desig_Description" : "Wood Fixer","SalaryBasis" : "Weekly","FixedSalary" : "185.00"},{"Emp_Id" : "17","Identity_No" : "","Emp_Name" : "Tamil arasi","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Wood Helper","Desig_Description" : "Wood Helper","SalaryBasis" : "Weekly","FixedSalary" : "185.00"},{"Emp_Id" : "18","Identity_No" : "","Emp_Name" : "Perumal","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Cook","Desig_Description" : "Cook","SalaryBasis" : "Weekly","FixedSalary" : "105.00"},{"Emp_Id" : "19","Identity_No" : "","Emp_Name" : "Andiappan","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Watchman","Desig_Description" : "Watchman","SalaryBasis" : "Weekly","FixedSalary" : "150.00"}]} And as of now my result looks like this, http://img401.imageshack.us/img401/2500/yuidtsum.jpg I have used jquery for this, var jsonObj = JSON.parse(HfJsonValue); for (var i = jsonObj.Table.length - 1; i >= 0; i--) { var employee = jsonObj.Table[i]; $('<div class="resultsdiv"><br /><span class="resultName">' + employee.Emp_Name + '</span><span class="resultfields" style="padding-left:100px;">Category&nbsp;:</span>&nbsp;<span class="resultfieldvalues">' + employee.Desig_Name + '</span><br /><br /><span id="SalaryBasis" class="resultfields">Salary Basis&nbsp;:</span>&nbsp;<span class="resultfieldvalues">' + employee.SalaryBasis + '</span><span class="resultfields" style="padding-left:25px;">Salary&nbsp;:</span>&nbsp;<span class="resultfieldvalues">' + employee.FixedSalary + '</span><span style="font-size:110%;font-weight:bolder;padding-left:25px;">Address&nbsp;:</span>&nbsp;<span class="resultfieldvalues">' + employee.Address + '</span></div>').insertAfter('#ResultsDiv'); } My image contains only 6 records as of now.. Any suggestions?

    Read the article

  • Tridion Installation

    - by Kevin Brydon
    I am currently upgrading an installation of Tridion from 5.3 to 2011 starting almost from scratch (aside from migrating the database), brand new virtual servers. I just want to ask for some advice on my current server setup... a sanity check. All servers are running Windows Server 2008. The pages on our website are all classic ASP. Database SQL Server cluster. The 5.3 database has been migrated using the DatabaseManager. This is pretty standard and works well (in test anyway). Content Manager A single server to run the Content Manager and the Publisher. There are around 10 people using it at any one time so not under a particularly heavy load. Content Data Store Filesystem located somewhere on the network. One directory for live and one for staging. Content Delivery Two servers (cd1 and cd2) each with the the following server roles installed. cd1 writes to a filesystem content data store for the live website, cd2 writes to the content data store for the staging website. Presentation Two public facing web servers (web1 and web2) serving both the live and staging websites. The web servers read directly from the content data store as its a filesystem. Each of the web servers have the Content Delivery Server installed so that I can use dynamic linking (and other features?). I've so far set up everything but the web servers. Any thoughts? edit Thanks to Ram S who linked me to a decent walkthrough, upvoted. I suppose I should have posed some questions as I didn't really ask a question. I guess I'm a little confused over the content deliver aspect. I have the Content Delivery split in two separate parts. cd1 and cd2 do the work of shifting information from the Content Manager to the Staging/Live web directories. web1 and web2 should do the work of serving the web pages to the outside world and will interact with the content data store (file system). Is this a correct setup? I need some parts of the Content Delivery on my web servers right? Theoretically I could get rid of the cd1 and cd2 servers and use web1 and web2 to do the deployment right? But I suspect this will put the web servers under unnecessary strain should there ever be a big publish. I've been reading the 2011 Installation Manual, Content Delivery section, and I'm finding it quite hard to get my head around!

    Read the article

  • Good jquery pagination plugin to use with json Data...

    - by bala3569
    I am looking for a good jquery pagination plugin to use in my aspx page.... I have the following parameters currentpage,pagesize,TotalRecords,NumberofPages... I would like my plugin to same as stackoverflow paging .... EDIT: It should paginate through json data.... similar to this I use my json data and iterating with jquery var jsonObj = jQuery.parseJSON(HfJsonValue); for (var i = jsonObj.Table.length - 1; i >= 0; i--) { var employee = jsonObj.Table[i]; $('<div class="resultsdiv"><br /><span class="resultName">' + employee.Emp_Name + '</span><span class="resultfields" style="padding-left:100px;">Category&nbsp;:</span>&nbsp;<span class="resultfieldvalues">' + employee.Desig_Name + '</span><br /><br /><span id="SalaryBasis" class="resultfields">Salary Basis&nbsp;:</span>&nbsp;<span class="resultfieldvalues">' + employee.SalaryBasis + '</span><span class="resultfields" style="padding-left:25px;">Salary&nbsp;:</span>&nbsp;<span class="resultfieldvalues">' + employee.FixedSalary + '</span><span style="font-size:110%;font-weight:bolder;padding-left:25px;">Address&nbsp;:</span>&nbsp;<span class="resultfieldvalues">' + employee.Address + '</span></div>').insertAfter('#ResultsDiv'); } There are 25 divs in my page as a result i want to show first five divs in page 1 and so on... Any suggestion... My HfJsonValue contains the following json data {"Table" : [{"Emp_Id" : "3","Identity_No" : "","Emp_Name" : "Jerome","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Supervisior","Desig_Description" : "Supervisior of the Construction","SalaryBasis" : "Monthly","FixedSalary" : "25000.00"},{"Emp_Id" : "4","Identity_No" : "","Emp_Name" : "Mohan","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Acc ","Desig_Description" : "Accountant","SalaryBasis" : "Monthly","FixedSalary" : "200.00"},{"Emp_Id" : "5","Identity_No" : "","Emp_Name" : "Murugan","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Mason","Desig_Description" : "Mason","SalaryBasis" : "Weekly","FixedSalary" : "150.00"},{"Emp_Id" : "6","Identity_No" : "","Emp_Name" : "Ram","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Mason","Desig_Description" : "Mason","SalaryBasis" : "Weekly","FixedSalary" : "120.00"},{"Emp_Id" : "7","Identity_No" : "","Emp_Name" : "Raja","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Mason","Desig_Description" : "Mason","SalaryBasis" : "Weekly","FixedSalary" : "135.00"},{"Emp_Id" : "8","Identity_No" : "","Emp_Name" : "Raja kumar","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Mason Helper","Desig_Description" : "Mason Helper","SalaryBasis" : "Weekly","FixedSalary" : "105.00"},{"Emp_Id" : "9","Identity_No" : "","Emp_Name" : "Lakshmi","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Mason Helper","Desig_Description" : "Mason Helper","SalaryBasis" : "Weekly","FixedSalary" : "100.00"},{"Emp_Id" : "10","Identity_No" : "","Emp_Name" : "Palani","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Carpenter","Desig_Description" : "Carpenter","SalaryBasis" : "Weekly","FixedSalary" : "200.00"},{"Emp_Id" : "11","Identity_No" : "","Emp_Name" : "Annamalai","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Carpenter","Desig_Description" : "Carpenter","SalaryBasis" : "Weekly","FixedSalary" : "220.00"},{"Emp_Id" : "12","Identity_No" : "","Emp_Name" : "David","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Steel Fixer","Desig_Description" : "Steel Fixer","SalaryBasis" : "Weekly","FixedSalary" : "220.00"},{"Emp_Id" : "13","Identity_No" : "","Emp_Name" : "Chandru","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Steel Fixer","Desig_Description" : "Steel Fixer","SalaryBasis" : "Weekly","FixedSalary" : "220.00"},{"Emp_Id" : "14","Identity_No" : "","Emp_Name" : "Mani","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Steel Helper","Desig_Description" : "Steel Helper","SalaryBasis" : "Weekly","FixedSalary" : "175.00"},{"Emp_Id" : "15","Identity_No" : "","Emp_Name" : "Karthik","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Wood Fixer","Desig_Description" : "Wood Fixer","SalaryBasis" : "Weekly","FixedSalary" : "195.00"},{"Emp_Id" : "16","Identity_No" : "","Emp_Name" : "Bala","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Wood Fixer","Desig_Description" : "Wood Fixer","SalaryBasis" : "Weekly","FixedSalary" : "185.00"},{"Emp_Id" : "17","Identity_No" : "","Emp_Name" : "Tamil arasi","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Wood Helper","Desig_Description" : "Wood Helper","SalaryBasis" : "Weekly","FixedSalary" : "185.00"},{"Emp_Id" : "18","Identity_No" : "","Emp_Name" : "Perumal","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Cook","Desig_Description" : "Cook","SalaryBasis" : "Weekly","FixedSalary" : "105.00"},{"Emp_Id" : "19","Identity_No" : "","Emp_Name" : "Andiappan","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Watchman","Desig_Description" : "Watchman","SalaryBasis" : "Weekly","FixedSalary" : "150.00"}]}

    Read the article

  • How to use jquery to paginate json data?

    - by Pandiya Chendur
    My json Data looks like this {"Table" : [{"Emp_Id" : "3","Identity_No" : "","Emp_Name" : "Jerome","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Supervisior","Desig_Description" : "Supervisior of the Construction","SalaryBasis" : "Monthly","FixedSalary" : "25000.00"},{"Emp_Id" : "4","Identity_No" : "","Emp_Name" : "Mohan","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Acc ","Desig_Description" : "Accountant","SalaryBasis" : "Monthly","FixedSalary" : "200.00"},{"Emp_Id" : "5","Identity_No" : "","Emp_Name" : "Murugan","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Mason","Desig_Description" : "Mason","SalaryBasis" : "Weekly","FixedSalary" : "150.00"},{"Emp_Id" : "6","Identity_No" : "","Emp_Name" : "Ram","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Mason","Desig_Description" : "Mason","SalaryBasis" : "Weekly","FixedSalary" : "120.00"},{"Emp_Id" : "7","Identity_No" : "","Emp_Name" : "Raja","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Mason","Desig_Description" : "Mason","SalaryBasis" : "Weekly","FixedSalary" : "135.00"},{"Emp_Id" : "8","Identity_No" : "","Emp_Name" : "Raja kumar","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Mason Helper","Desig_Description" : "Mason Helper","SalaryBasis" : "Weekly","FixedSalary" : "105.00"},{"Emp_Id" : "9","Identity_No" : "","Emp_Name" : "Lakshmi","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Mason Helper","Desig_Description" : "Mason Helper","SalaryBasis" : "Weekly","FixedSalary" : "100.00"},{"Emp_Id" : "10","Identity_No" : "","Emp_Name" : "Palani","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Carpenter","Desig_Description" : "Carpenter","SalaryBasis" : "Weekly","FixedSalary" : "200.00"},{"Emp_Id" : "11","Identity_No" : "","Emp_Name" : "Annamalai","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Carpenter","Desig_Description" : "Carpenter","SalaryBasis" : "Weekly","FixedSalary" : "220.00"},{"Emp_Id" : "12","Identity_No" : "","Emp_Name" : "David","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Steel Fixer","Desig_Description" : "Steel Fixer","SalaryBasis" : "Weekly","FixedSalary" : "220.00"},{"Emp_Id" : "13","Identity_No" : "","Emp_Name" : "Chandru","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Steel Fixer","Desig_Description" : "Steel Fixer","SalaryBasis" : "Weekly","FixedSalary" : "220.00"},{"Emp_Id" : "14","Identity_No" : "","Emp_Name" : "Mani","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Steel Helper","Desig_Description" : "Steel Helper","SalaryBasis" : "Weekly","FixedSalary" : "175.00"},{"Emp_Id" : "15","Identity_No" : "","Emp_Name" : "Karthik","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Wood Fixer","Desig_Description" : "Wood Fixer","SalaryBasis" : "Weekly","FixedSalary" : "195.00"},{"Emp_Id" : "16","Identity_No" : "","Emp_Name" : "Bala","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Wood Fixer","Desig_Description" : "Wood Fixer","SalaryBasis" : "Weekly","FixedSalary" : "185.00"},{"Emp_Id" : "17","Identity_No" : "","Emp_Name" : "Tamil arasi","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Wood Helper","Desig_Description" : "Wood Helper","SalaryBasis" : "Weekly","FixedSalary" : "185.00"},{"Emp_Id" : "18","Identity_No" : "","Emp_Name" : "Perumal","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Cook","Desig_Description" : "Cook","SalaryBasis" : "Weekly","FixedSalary" : "105.00"},{"Emp_Id" : "19","Identity_No" : "","Emp_Name" : "Andiappan","Address" : "Madurai","Date_Of_Birth" : "","Desig_Name" : "Watchman","Desig_Description" : "Watchman","SalaryBasis" : "Weekly","FixedSalary" : "150.00"}]} There are 22 records in this json... How to paginate this json data 5 per page using jquery? EDIT: The above image is my summary view of employee list iterated using jquery var jsonObj = JSON.parse(HfJsonValue); for (var i = jsonObj.Table.length - 1; i >= 0; i--) { var employee = jsonObj.Table[i]; $('<div class="resultsdiv"><br /><span class="resultName">' + employee.Emp_Name + '</span><span class="resultfields" style="padding-left:100px;">Category&nbsp;:</span>&nbsp;<span class="resultfieldvalues">' + employee.Desig_Name + '</span><br /><br /><span id="SalaryBasis" class="resultfields">Salary Basis&nbsp;:</span>&nbsp;<span class="resultfieldvalues">' + employee.SalaryBasis + '</span><span class="resultfields" style="padding-left:25px;">Salary&nbsp;:</span>&nbsp;<span class="resultfieldvalues">' + employee.FixedSalary + '</span><span style="font-size:110%;font-weight:bolder;padding-left:25px;">Address&nbsp;:</span>&nbsp;<span class="resultfieldvalues">' + employee.Address + '</span></div>').insertAfter('#ResultsDiv'); } I get 22 records now it may grow how to paginate json date by using jquery pagination.. Any suggestion...

    Read the article

  • Fulltext search for django : Mysql not so bad ? (vs sphinx, xapian)

    - by Eric
    I am studying fulltext search engines for django. It must be simple to install, fast indexing, fast index update, not blocking while indexing, fast search. After reading many web pages, I put in short list : Mysql MYISAM fulltext, djapian/python-xapian, and django-sphinx I did not choose lucene because it seems complex, nor haystack as it has less features than djapian/django-sphinx (like fields weighting). Then I made some benchmarks, to do so, I collected many free books on the net to generate a database table with 1 485 000 records (id,title,body), each record is about 600 bytes long. From the database, I also generated a list of 100 000 existing words and shuffled them to create a search list. For the tests, I made 2 runs on my laptop (4Go RAM, Dual core 2.0Ghz): the first one, just after a server reboot to clear all caches, the second is done juste after in order to test how good are cached results. Here are the "home made" benchmark results : 1485000 records with Title (150 bytes) and body (450 bytes) Mysql 5.0.75/Ubuntu 9.04 Fulltext : ========================================================================== Full indexing : 7m14.146s 1 thread, 1000 searchs with single word randomly taken from database : First run : 0:01:11.553524 next run : 0:00:00.168508 Mysql 5.5.4 m3/Ubuntu 9.04 Fulltext : ========================================================================== Full indexing : 6m08.154s 1 thread, 1000 searchs with single word randomly taken from database : First run : 0:01:11.553524 next run : 0:00:00.168508 1 thread, 100000 searchs with single word randomly taken from database : First run : 9m09s next run : 5m38s 1 thread, 10000 random strings (random strings should not be found in database) : just after the 100000 search test : 0:00:15.007353 1 thread, boolean search : 1000 x (+word1 +word2) First run : 0:00:21.205404 next run : 0:00:00.145098 Djapian Fulltext : ========================================================================== Full indexing : 84m7.601s 1 thread, 1000 searchs with single word randomly taken from database with prefetch : First run : 0:02:28.085680 next run : 0:00:14.300236 python-xapian Fulltext : ========================================================================== 1 thread, 1000 searchs with single word randomly taken from database : First run : 0:01:26.402084 next run : 0:00:00.695092 django-sphinx Fulltext : ========================================================================== Full indexing : 1m25.957s 1 thread, 1000 searchs with single word randomly taken from database : First run : 0:01:30.073001 next run : 0:00:05.203294 1 thread, 100000 searchs with single word randomly taken from database : First run : 12m48s next run : 9m45s 1 thread, 10000 random strings (random strings should not be found in database) : just after the 100000 search test : 0:00:23.535319 1 thread, boolean search : 1000 x (word1 word2) First run : 0:00:20.856486 next run : 0:00:03.005416 As you can see, Mysql is not so bad at all for fulltext search. In addition, its query cache is very efficient. Mysql seems to me a good choice as there is nothing to install (I need just to write a small script to synchronize an Innodb production table to a MyISAM search table) and as I do not really need advanced search feature like stemming etc... Here is the question : What do you think about Mysql fulltext search engine vs sphinx and xapian ?

    Read the article

  • Java ExecutorService java heap space ptoblems

    - by Sergey Aganezov jr
    I have a little bit of a problem in a multitasking java department. I have a class, called public class ThreadWorker implements Runnable { //some code in here public void run(){ // invokes some recursion method in the ThreadWorker itself, // which will stop eventually { } all in all, pretty simple "worker" that can work on it's on. To work with threads I'm using public static int THREAD_NUMBER = 4; public static ExecutorServide es = Executors.newFixedThreadPool(THREAD_NUMBER); adding instances of ThreadWroker class happens here: public void recursiveMethod(Arraylist<Integers> elements, MyClass data){ if (elements.size() == 0 && data.qualifies()){ ThreadWorker tw = new ThreadWorker(data); es.execute(tw); return; } for (int i=0; i< elements.size(); i++){ // some code to prevent my problem MyClass data1 = new MyClass(data); MyClass data2 = new MyClass(data); ArrayList<Integer> newElements = (ArrayList<Integer>)elements.clone(); data1.update(elements.get(i)); data2.update(-1 * elements.get(i)); newElements.remove(i); recursiveMethod(newElements, data1); recursiveMethod(newElements, data2); { } and the problem is that the depth of the recursion tree is quite big, so as it's width, so a lot of ThreadWorkers are added to the ExecutorService, so after some time on the big input a get Exception in thread "pool-1-thread-2" java.lang.OutOfMemoryError: Java heap space which is caused, as I think because of a ginormous number of ThreadWorkers i'm adding to ExecutorSirvice to be executed, so it runs out of memory. Every ThreadWorker takes about 40 Mb of RAM for all it needs. Is there a method to get how many threads (instances of classes implementing runnable interface) have been added to ExecutorService? So I can add it in the shown above code (int the " // some code to prevent my problem"), as while ("number of threads in the ExecutorService" > 10){ Thread.sleep(10000); } so I won't go to deep or to broad with my recursion and prevent those exception-throwing situations. Sincerely, Sergey Aganezov jr.

    Read the article

  • Is this asking too much of a browser?

    - by Matt Ball
    I'm embedding a large array in <script> tags in my HTML, like this (nothing surprising): <script> var largeArray = [/* lots of stuff in here */]; </script> In this particular example, the array has 210,000 elements. That's well below the theoretical maximum of 231 - by 4 orders of magnitude. Here's the fun part: if I save JS source for the array to a file, that file is 44 megabytes (46,573,399 bytes, to be exact). If you want to see for yourself, you can download it from my Dropbox. (All the data in there is canned, so much of it is repeated. This will not be the case in production.) Now, I'm really not concerned about serving that much data. My server gzips its responses, so it really doesn't take all that long to get the data over the wire. However, there is a really nasty tendency for the page, once loaded, to crash the browser. I'm not testing at all in IE (this is an internal tool). My primary targets are Chrome 8 and Firefox 3.6. In Firefox, I can see a reasonably useful error in the console: Error: script stack space quota is exhausted In Chrome, I simply get the sad-tab page: Cut to the chase, already Is this really too much data for our modern, "high-performance" browsers to handle? Is there anything I can do* to gracefully handle this much data? Incidentally, I was able to get this to work (read: not crash the tab) on-and-off in Chrome. I really thought that Chrome, at least, was made of tougher stuff, but apparently I was wrong... Edit 1 @Crayon: I wasn't looking to justify why I'd like to dump this much data into the browser at once. Short version: either I solve this one (admittedly not-that-easy) problem, or I have to solve a whole slew of other problems. I'm opting for the simpler approach for now. @various: right now, I'm not especially looking for ways to actually reduce the number of elements in the array. I know I could implement Ajax paging or what-have-you, but that introduces its own set of problems for me in other regards. @Phrogz: each element looks something like this: {dateTime:new Date(1296176400000), terminalId:'terminal999', 'General___BuildVersion':'10.05a_V110119_Beta', 'SSM___ExtId':26680, 'MD_CDMA_NETLOADER_NO_BCAST___Valid':'false', 'MD_CDMA_NETLOADER_NO_BCAST___PngAttempt':0} @Will: but I have a computer with a 4-core processor, 6 gigabytes of RAM, over half a terabyte of disk space ...and I'm not even asking for the browser to do this quickly - I'm just asking for it to work at all! ? *other than the obvious: sending less data to the browser

    Read the article

  • Why does this thumbnail generation code throw OutOfMemoryException on large files?

    - by tsilb
    This code works great for generating thumbnails, but when given a very large (100MB+) TIFF file, it throws OutOfMemoryExceptions. When I do it manually in Paint.NET on the same machine, it works fine. How can I improve this code to stop throwing on very large files? In this case I'm loading a 721MB TIF on a machine with 8GB RAM. The Task Manager shows 2GB used so something is preventing it from using all that memory. Specifically it throws when I load the Image to calculate the size of the original. What gives? /// <summary>Creates a thumbnail of a given image.</summary> /// <param name="inFile">Fully qualified path to file to create a thumbnail of</param> /// <param name="outFile">Fully qualified path to created thumbnail</param> /// <param name="x">Width of thumbnail</param> /// <returns>flag; result = is success</returns> public static bool CreateThumbnail(string inFile, string outFile, int x) { // Validation - assume 16x16 icon is smallest useful size. Smaller than that is just not going to do us any good anyway. I consider that an "Exceptional" case. if (string.IsNullOrEmpty(inFile)) throw new ArgumentNullException("inFile"); if (string.IsNullOrEmpty(outFile)) throw new ArgumentNullException("outFile"); if (x < 16) throw new ArgumentOutOfRangeException("x"); if (!File.Exists(inFile)) throw new ArgumentOutOfRangeException("inFile", "File does not exist: " + inFile); // Mathematically determine Y dimension int y; using (Image img = Image.FromFile(inFile)) { // OutOfMemoryException double xyRatio = (double)x / (double)img.Width; y = (int)((double)img.Height * xyRatio); } // All this crap could have easily been Image.Save(filename, x, y)... but nooooo.... using (Bitmap bmp = new Bitmap(inFile)) using (Bitmap thumb = new Bitmap((Image)bmp, new Size(x, y))) using (Graphics g = Graphics.FromImage(thumb)) { g.SmoothingMode = System.Drawing.Drawing2D.SmoothingMode.HighQuality; g.InterpolationMode = System.Drawing.Drawing2D.InterpolationMode.High; g.CompositingQuality = System.Drawing.Drawing2D.CompositingQuality.HighQuality; System.Drawing.Imaging.ImageCodecInfo codec = System.Drawing.Imaging.ImageCodecInfo.GetImageEncoders()[1]; System.Drawing.Imaging.EncoderParameters ep2 = new System.Drawing.Imaging.EncoderParameters(1); ep2.Param[0] = new System.Drawing.Imaging.EncoderParameter(System.Drawing.Imaging.Encoder.Quality, 100L); g.DrawImage(bmp, new Rectangle(0,0,thumb.Width, thumb.Height)); try { thumb.Save(outFile, codec, ep2); return true; } catch { return false; } } }

    Read the article

  • How to maximize http.sys file upload performance

    - by anelson
    I'm building a tool that transfers very large streaming data sets (possibly on the order of terabytes in a single stream; routinely in the tens of gigabytes) from one server to another. The client portion of the tool will read blocks from the source disk, and send them over the network. The server side will read these blocks off the network and write them to a file on the server disk. Right now I'm trying to decide which transport to use. Options are raw TCP, and HTTP. I really, REALLY want to be able to use HTTP. The HttpListener (or WCF if I want to go that route) make it easy to plug in to the HTTP Server API (http.sys), and I can get things like authentication and SSL for free. The problem right now is performance. I wrote a simple test harness that sends 128K blocks of NULL bytes using the BeginWrite/EndWrite async I/O idiom, with async BeginRead/EndRead on the server side. I've modified this test harness so I can do this with either HTTP PUT operations via HttpWebRequest/HttpListener, or plain old socket writes using TcpClient/TcpListener. To rule out issues with network cards or network pathways, both the client and server are on one machine and communicate over localhost. On my 12-core Windows 2008 R2 test server, the TCP version of this test harness can push bytes at 450MB/s, with minimal CPU usage. On the same box, the HTTP version of the test harness runs between 130MB/s and 200MB/s depending upon how I tweak it. In both cases CPU usage is low, and the vast majority of what CPU usage there is is kernel time, so I'm pretty sure my usage of C# and the .NET runtime is not the bottleneck. The box has two 6-core Xeon X5650 processors, 24GB of single-ranked DDR3 RAM, and is used exclusively by me for my own performance testing. I already know about HTTP client tweaks like ServicePointManager.MaxServicePointIdleTime, ServicePointManager.DefaultConnectionLimit, ServicePointManager.Expect100Continue, and HttpWebRequest.AllowWriteStreamBuffering. Does anyone have any ideas for how I can get HTTP.sys performance beyond 200MB/s? Has anyone seen it perform this well on any environment?

    Read the article

  • Git sh.exe process forking issue on windows XP, slow?

    - by AndyL
    Git is essential to my workflow. I run MSYS Git on Windows XP on my quad core machine with 3GB of RAM, and normally it is responsive and zippy. Suddenly an issue has cropped up whereby it takes 30 seconds to run any command from the Git Bash command prompt, including ls or cd. Interestingly, from the bash prompt it looks likes ls runs fairly quickly, I can then see the output from ls, but it then takes ~30 seconds for the prompt to return. If I switch to the windows command prompt (by running cmd from the start menu) git related commands also take forever, even just to run. For example git status can take close to a minute before anything happens. Sometimes the processes simply don't finish. Note that I have "MSYS Git" installed as well as regular "MSYS" for things like MinGW and make. I believe the problem is related to sh.exe located in C:\Program Files\Git\bin. When I run ls from the bash prompt, or when I invoke git from the windows prompt, task manager shows up to four instances of sh.exe processes that come and go. Here I am waiting for ls to return and you can see the task manager has git.exe running and four instances of sh.exe: If I ctrl-c in the middle of an ls I sometimes get errors that include: sh.exe": fork: Resource temporarily unavailable 0 [main] sh.exe" 1624 proc_subproc: Couldn't duplicate my handle<0x6FC> fo r pid 6052, Win32 error 5 sh.exe": fork: Resource temporarily unavailable Or for git status: $ git status sh.exe": fork: Resource temporarily unavailable sh.exe": fork: Resource temporarily unavailable sh.exe": fork: Resource temporarily unavailable sh.exe": fork: Resource temporarily unavailable Can I fix this so that git runs quickly again, and if so how? Things I have tried: Reboot Upgrade MSYS Git to most recent version & Reboot Upgrade MSYS to most recent version & Reboot Uninstall MSYS & uninstall and reinstall MSYS Git alone & Reboot I'd very much like to not wipe my box and reinstall Windows, but I will if I can't get this fixed. I can no longer code if it takes me 30 s to run git status or cd.

    Read the article

  • Is this slow WPF TextBlock performance expected?

    - by Ben Schoepke
    Hi, I am doing some benchmarking to determine if I can use WPF for a new product. However, early performance results are disappointing. I made a quick app that uses data binding to display a bunch of random text inside of a list box every 100 ms and it was eating up ~15% CPU. So I made another quick app that skipped the data binding/data template scheme and does nothing but update 10 TextBlocks that are inside of a ListBox every 100 ms (the actual product wouldn't require 100 ms updates, more like 500 ms max, but this is a stress test). I'm still seeing ~10-15% CPU usage. Why is this so high? Is it because of all the garbage strings? Here's the XAML: <Grid> <ListBox x:Name="numericsListBox"> <ListBox.Resources> <Style TargetType="TextBlock"> <Setter Property="FontSize" Value="48"/> <Setter Property="Width" Value="300"/> </Style> </ListBox.Resources> <TextBlock/> <TextBlock/> <TextBlock/> <TextBlock/> <TextBlock/> <TextBlock/> <TextBlock/> <TextBlock/> <TextBlock/> <TextBlock/> </ListBox> </Grid> Here's the code behind: public partial class Window1 : Window { private int _count = 0; public Window1() { InitializeComponent(); } private void OnLoad(object sender, RoutedEventArgs e) { var t = new DispatcherTimer(TimeSpan.FromSeconds(0.1), DispatcherPriority.Normal, UpdateNumerics, Dispatcher); t.Start(); } private void UpdateNumerics(object sender, EventArgs e) { ++_count; foreach (object textBlock in numericsListBox.Items) { var t = textBlock as TextBlock; if (t != null) t.Text = _count.ToString(); } } } Any ideas for a better way to quickly render text? My computer: XP SP3, 2.26 GHz Core 2 Duo, 4 GB RAM, Intel 4500 HD integrated graphics. And that is an order of magnitude beefier than the hardware I'd need to develop for in the real product.

    Read the article

  • R Install/Update on Mac OS X (Snow Leopard): where does R put files during install/config?

    - by doug
    In sum, there's a stray preference-like file or two (probably just one) that i can't find. Here's the whole story: I recently attempted to update my R install from 2.10 to 2.11. As i have done before, i installed from source. I know that all of the dependencies are correctly installed and made available to R, because my prior install worked fine. When i upgraded to 2.11, i am unable to install packages (no exception thrown, it just doesn't appear to complete the install and is unresponsive so i have to quit + restart R. Given i install from source, there are any number of points in the process that i could have messed up. What i need to do now is "start over" which requires that i clear out my my prior install. I am having trouble doing that. There is still at least one preference file or something like that i can't find and one of these is causing the problem, so i need to find it and terminate it with extreme prejudice before i do a fresh install. Although i set a number of flags during the install, i have never opted out of the default install locations during the config step. There has to be one or more preference files still in my file structure (and that's also accessible to the new install of R) because after i follow all of the steps below, then do a fresh install, when i start R for the first time, some of my preferences have persisted (e.g., quartz settings, GUI background color, editor selection, etc.). Again, the problem is that i just cannot locate those files. Finally, the problem can't be that during my last install from source, i inadvertently caused a preference file to be sent to an off-spec location--because again, a fresh R install (whether from source or from the OS X binaries) is finding those files Here's what i've done prior to attempting a clean install of R: Removed files from these locations: ~/.RData ~/.RHistory /Applications/R64.app /Applications/R.app /Library/Frameworks/R.framework (i also removed all symlinks from these) Cleared all RAM and disk caches, in particular the directory where i know R caches: ~/Library/Caches/R* (in fact i've cleared this entire directory) Checked for all 'hidden' files in the OS X directories where login/startup files are often placed: /etc/ ~/ In addition, i've checked R-help, and i've also read through the relevant portions of 'R Installation and Administration'--no luck. I've also searched searched my file structure using the various bash utilities, which nearly always solves problems of this sort quite easily, but in this case obviously searching by name or even pattern is more problematic.

    Read the article

< Previous Page | 181 182 183 184 185 186 187 188 189 190 191  | Next Page >