Search Results

Search found 12264 results on 491 pages for 'drive letter'.

Page 187/491 | < Previous Page | 183 184 185 186 187 188 189 190 191 192 193 194  | Next Page >

• Computer always freezing after random periods of time. No errors listed.

  - by Wesley

  Hi, all. Here are my specs beforehand: AMD Athlon XP 2400+ @ 2.00 GHz, 160GB IDE HDD, 128MB GeForce 6200 AGP, 2 x 512MB PC3200 DDR RAM, CoolMax 350W PSU, 1 x CD-RW Drive, 1 x DVD-ROM Drive, FIC AM37 Mobo, Windows XP Pro SP3 My desktop freezes after random periods of time but there are no errors listed in the Event Viewer after a forced shutdown and restart. A couple months ago, I found that when it froze, the floppy was being accessed at the same time. So, I disconnected the floppy (since I never used it anyways) from the power supply and motherboard. Everything was working fine and the computer never froze. This past Christmas break, I left for a Conference and when I got home, the computer kept freezing again. So, this time, I just disconnected the DVD reader (from mobo and power) and started it up. Still, it froze almost right away. Then I found some older sticks of RAM (2 x 256MB PC2100 DDR) and swapped them in. Everything worked fine again after that. I even swapped the 2 x 512MB PC3200 DDR RAM back in and everything worked okay. Then it started freezing again, and I tried all possible RAM combos, still freezing within 5-10 minutes of startup. One thing I've realized is that the floppy drive is still listed in My Computer and I uninstalled it from my Device Manager already. There were no software errors, and I uninstalled the most recent software, with no effect. Still, I have no idea what is wrong because everything ran fine before that. Any suggestions? EDIT: Still have yet to buy some blank CD media to use Memtest86+. However, would a lack of virtual memory cause the computer to freeze? EDIT2: So after a long time, I ran Memtest86+ and all is well. Turns out though, after removing my original DVD reader and replacing it with a DVD-ROM drive, there is no freezing whatsoever! Thanks for all your suggestions!

  Read the article

• Dell XPS 1530 DVD-RW firmware problem

  - by josecortesp

  Hello everyone. I have this XPS laptop since a year and a half ago. About 2 months ago, with the waranty expired, i tried to run the optiarc slot load DVD-RW firmware update, and said everything was okay. Then I restarted it and the problem started: Now, every single time I turn on my computer, it get stuck at the BIOS POST until the drive sounds like "ready" and then the computer starts normally. And this happen EXACTLY the same when it's getting back from sleep. I'm pretty sure is not a software issue, because I tried with Vista Home Premiun 32 bits, Ubuntu (from 8.10+)32 & 64, and with W7 64. Already tried to run the firmware installer like a million time, in case it is a failing install with no luck. Also, google it to see if someone has the same problem, and again, no. The Drive performs pretty okay once the System is on, but waiting to the drive to be ready everytime is really annoying. The Firmware I updated was this, and the drive is: K937C Assembly, Dvd+/-rw, 8, SLOT, 1530 Sony Nec Optiarc Inc. I'll apreciate any help you can give me

  Read the article

• Why is the Windows 8 recycle bin using more space than it is allocated?

  - by oldmankit

  I ran WinDirStat to scan the contents of my hard drive. I was surprised to see that the $RECYCLE.BIN folder on my D: drive takes 26 GB of space. I emptied the recycle bin, refreshed the folder in WinDirStat, but it still takes 26 GB of space. I reduced the Maximum size of the recycle bin for this drive to 10000 MB for the main user of this computer, and disabled the recycle bin for the other user, and refreshed the folder in WinDirStat, but it still takes 26 GB of space. I ran (in an elevated window) rd /s D:\$Recycle.bin, and refreshed the folder in WinDirStat, and finally it became empty. Why was it taking up space even after I emptied it? Why was it taking more space (26 GB) than the maximum allowed amount (10 GB)? Update: After six months of using Windows (no re-install and no changes of settings related to the Recycle Bin) I used WinDirStat to check how big D:\$RECYCLE.BIN has become. It is now 29 GB. In Recycle Bin Properties, I select drive D, and it is still a custom maximum size (10000 MB).

  Read the article

• How do I rename my old Program Files folder?

  - by SteveJ

  I installed a new SSD as my boot drive (C:), installed a fresh version of Windows 7 64-bit, and kept my existing SATA drive in the system (D:). I want to keep using my D: drive for file storage (no sense filling up the SSD with stuff that isn't performance critical) and I haven't formatted the D: drive because there's stuff on there I want to keep. I also want to create a new "D:\Program Files" folder so I can install apps that aren't performance-critical there. So I decided I'd rename the existing "D:\Program Files" from my old Windows install to "D:\Old Program Files" and then create a new "D:\Program Files" directory. Easy, right? I can see "D:\Program Files" just fine in Explorer. I right click, select Rename, and type "Old Program Files." I get the alert that says I need Admin permission to do this, so I press the confirm button with the shield. But the folder still appears as "Program Files" in Explorer. I jump out to the command line, and it appears as "Old Program Files" when I do a dir. I can even do mkdir "Program Files" and when I do a dir they both appear. But in the Explorer GUI, it looks like I have two "Program Files" folders. This will be confusing during app installation because I won't be able to tell which one is which. I've tried poking around in the properties tab of the old folder, but can't find anything that would explain what's causing the issue. How do I rename the old Program Files folder?

  Read the article

• How to record tv to network share with Windows Media Center?

  - by Peterdk

  Well, you would think that Windows 7's new MediaCenter would be up to the task of recording your TV to a network share/drive. Too bad, it looks like it's just not possible. I have a windows 2008 R2 server, and a Windows 7 machine with a TV card. Since my server has 2TB of storage, it would be nice to record directly to it's networked drive. (I mounted it as Z:). I tried the following: Selecting it in Media Center Itself: Not working. Not available. Editing the registry: HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Media Center\Service\Recording , setting RecordPath to Z:\TV. Not working. Editing the registry: setting RecordPath to \\server\TV. Not working. Creating a Symlink (mklink \D) to Z:\TV and \\server\TV and setting that in the registry as RecordPath. Currently I am out of options. I could ofcourse Install Windows7 on my server, but I have no license for that, and my windows 2008 r2 is free from dreamspark. Are there people that are succesfully recording to a networked drive/storage? edit I also need to mention that I need to be able to acces the stored files from other PC's, like my laptop. So iSCSI is great for recording, but it looks like you can't access iSCSI devices from multiple PC's. Looks like sharing a iSCSI device is out of the question, so: Are there workarounds to get this thing recording to my network drive?

  Read the article

• Re-installing Windows on an old laptop

  - by Khaled

  I have an old laptop and I want to re-install Windows XP on it. The problem is that this laptop does not have an optical drive. I checked the boot sequence in the BIOS. It does not show an option to boot from USB. It have only two options: Boot from HD. Boot using Realtek agent (network boot). I tried to copy the Windows CD to second drive D:\ and run the installed from there. However, I could not format the C:\ drive. Windows complaints about setup files will be removed or something like that. I tried to boot the laptop using PXE, but I could not. It seems that the DHCP request did not get answered. I thought I could use a USB CD-ROM drive (I don't have one to try), but it might not work as there is no option to boot from USB. Do you think it will work? Do I have other options to try? Any recommendations?

  Read the article

• Help with Ubuntu and Windows, separate HDs

  - by LuxuryMode

  Need some major help. Running a Dell XPS/Dimension 630i. It came with "SATA 2 RAID 0 With Dual 500GB Hard Drives." I have installed a new, third non-raided drive and installed Ubuntu on it. So now I have Windows on the original hard drive and Ubuntu Linux on the new HD. When I get to the boot menu where I can select an OS, if I select windows I get an error: "No such drive, no such disk." Also, strangely in the first place, in order to even get to the bootloader menu I have had to disable ALL ports under the RAID config. Unless I do this, I will just get to a never-ending blinking cursor. I have tried every conceivable CMOS config and nothing else works. Tried setting port 3 (the new HD w/ Ubuntu) to first hard disk boot priority. Tried disabling all other ports and enabling the Ubuntu HD port and vice versa. I have some pictures of boot up: first one is strange error i get after messing with CMOS to finally get ubuntu install to work. http://imgur.com/5sqJa then boot menu: http://imgur.com/TWtLq then error: http://imgur.com/TJ1mS. Also, please note that I can actually access all files from the raided Windows drive through Ubuntu.

  Read the article

• Master File Table Corrupt, any way to save data?

  - by domen

  hi. I've used search, but none of the results match my problem so I didn't have to ask separate question. I've Installed Windows 7 RTM recently and since then partitions located on one of my HDDs have gone "crazy". They used to "freeze" and didn't open in explorer for some time (minute or two, usually), sometimes all partitions of the drive wouldn't show until reboot and finally, one of those partitions started showing "disk structure is corrupted and unreadable" warning, it appeared in Disk Management window as RAW and chkdsk showed "mft corrupt". There were no important data on the partition and I didn't have enough time to analyze the problem at the moment, so I just reformatted it and ran antivirus scan on system. After that problem settled for some time, but yesterday the problematic HDD vanished again from the system. After reboot chkdsk identified mft of four partitions corrupt and now they are all in same conditions as the above mentioned one. But the difference is that the files stored in them are extremely important. and just for info: I upgraded from Win7 build 7077, but had some performance issues, so I reformatted system drive and installed fresh Win7 RTM on it. I've downloaded TestDisk and it shows all the partitions marked as NTFS (not RAW) and my knowledge of the program wasn't sufficient to obtain any other info from it :-) and the images that could help describe the problem (sorry, I'm not allowed to post images and more than one hyperlink): http:// img22.imageshack.us/img22/5909/chkdskz.jpg http:// img198.imageshack.us/img198/5576/computeray.jpg I'm interested, is there a way to let me restore the MFT or just access files so I can backup them before reformatting the drive. Thanks for your time. :) P.S. my reformatted drive is showing no problems, could there be a problem with windows 7 itself? I googled, but with no results.

  Read the article

• Dialog box tells me there's a missing driver when installing 64-bit version of Windows 7

  - by Eikern

  I'm trying to install Windows 7 64-bit on my computer (ASUS P6T Deluxe V2, one 80GB HDD and two 1 TB HDDs). When I'm supposed to select whether I want to Upgrade or do a Custom install, I get a dialog box telling me: Load Driver A required CD/DVD drive device driver is missing. If you have a driver floppy disk, CD, DVD, or USB flash drive, please insert it now. Note: If the Windows installation media is in the CD/DVD drive, you can safely remove it for this step. I've tried to reach this step using a 32-bit installation disc, but that doesn't generate this message at all. Through the command windows (shift-F10) I can reach all of my drives, including my optical drive, without any problems--so what kind of device driver is it the installation wants? I've tried all the obvious drivers on the CD that followed my motherboard, but I can't seem to find the right one. The problem is that I don't know what device I'm supposed to load the drivers for in the first place. Can anyone help me? Edit: It turned out that my downloaded image was corrupted. I borrowed a DVD from a friend of mine, which worked!

  Read the article

• break Folder Protection, Folder Guard Lock or Folder in Windows XP?

  - by SonyAdi

  when I'm making a new partition by the partition magic. Then all of a sudden power failure. Unfortunately because my computer is not equipped with UPS (Power supply Uniterruptible), my computer finally died, too. When power is restored, I tried to turn on the computer. Suddenly my computer can not boot normally into windows. Option through safemode and others all I've tried. The result fails, can not boot at all, into safe mode also can not. And I know the cause. Partition Magic did not finish the work and stopped in the middle of the road and cause the transfer of data files or stopped, finally file2 any default windows were destroyed as well. Unfortunately my important data I store in my document. Finally, I take my hard drive to a friend. Hopes to open a computer hard drive through friend, at least I could save my important data, and then I can install window again by reformatting my hard drive is first. I read the hard drive in explorer my friend, complete with their data, but the data of my important data in my document can not get to go because it requires administrator privileges or the original user's default start my windows (my computer) to open my document folder tersebut.Ini actually very similar to the work or Folder Protection Folder Guard. result I was disappointed and almost desperate to get back my important data is. how do i break Folder Protection, Folder Guard Lock or Folder in Windows XP?

  Read the article

• How do I recover drivers from other hard disk

  - by Carl

  The drivers for a Cardbus (PCMCIA) card that gives me 2 USB 2.0 ports are on the hard disk from my old laptop. I have lost the driver CD. I have a way to get files from that other hard disk. Which files do I need? The drivers for the card used to be on the following website - the information is still there, except the download links don't work: http://www.ht-link.com/en/DownView.asp?ID=10 - The drivers I need are the first listing - The Win XP drivers for the HT-112NEC. My e-mails to them have not been answered. The information on this card is here http://www.ht-link.com/en/ProductView.asp?ID=106 I already tried connecting that other drive to my new laptop (via USB) and adding the drive to the search criteria when selecting update driver in the Device Manager. It says there isn't a better match, and if I select manual the matching device is not listed. (I don't think "manual" sees drivers on the external hard disk - but only ones on the main drive and/or found listed in the registry.) I would try 'have disk' if I knew exactly what file to point to on the external drive. The drivers are on that hard disk - I installed them there, and used that card on that computer. The new laptop has Windows XP Pro SP3, the old one had Pro SP2 Thanks for any help.

  Read the article

• FreeNAS pool configuration - RAID1 + other drives

  - by trnelson

  Simple questions, really. I found this answer with a similar setup, but not sure it answers my question. If it does, I'm curious why since the answer seems a bit unsure: ZFS Hard Drive Configuration in FreeNAS I'm building a server which will be used primarily for backup, plus some media streaming, possibly with Plex. I seem to understand most everything I need, but I'm still a bit confused on how pools work, and how to configure them for my scenario. I will have 2x 2TB WD Red drives, which I plan on using in a mirrored set up (RAID1). This would be for backup, and I'd also like to do offsite backup to my CrashPlan account from this array. I also have a few other drives: 1.5TB, 320GB, 250GB. I'm not sure exactly what to do with them yet, but looking for options. FreeNAS OS will be running from a 16GB USB Flash drive. Would it be wise to use the 1.5TB as a backup-backup, essentially as a mirror or perhaps for snapshots of the 2TB RAID1? I'm still learning about snapshots. Should the 2TB mirrored drives be in their own pool? Should the other drives be set up in their own pools as well, or should they be JBOD in a single pool? They may or may not get much use since the 2TB array is plenty for me. Does a dataset basically mimic the idea of a partition or a network share? In other words, I would map \SERVER\Share to X: on my laptop? Let's say I wanted to use the 250GB drive as an encrypted drive to store all of my cat pictures. Would it have to be in its own pool? If I use jails apps, should they go in the backup RAID1, or in another place? Thank you!

  Read the article

• Cannot write to directory after taking ownership

  - by jeff charles

  I had a directory on an internal hard-drive that was created in an old Windows 7 install. After re-installing my operating system, when I try to create a new directory inside that directory, I get an Access Denied message. This isn't a protected directory, just a random directory I created at the drive root (that drive was not the C drive in either install). I tried to take ownership by opening folder properties, going to the Security tab, clicking on Advanced, going to Owner tab, clicking on Edit, selecting my user account, checking Replace owner on subcontainers and objects, and clicking Apply. There were no error messages and I closed the dialogs. I rebooted, checked the owner on that folder and a couple subfolders and it appears to be set correctly. I am still getting an Access Denied message however when trying to create a directory in it. I've also tried using attrib -R . to remove any possible readonly attribute inside the directory in an admin command prompt but am still unable to create a directory using a non-admin prompt (it does work in an admin prompt). Is there anything I can do to get write access to that folder and it's subcontents in a non-elevated context without disabling UAC?

  Read the article

• Having trouble with a workaround, for booting from a usb stick, using grub and a minimal linux kernel to load usb drivers

  - by s hanley

  I'm trying to boot from a usb stick. I formatted it to fat32, and later to ext2, and installed dsl on it using unetbootin, and later the usb install guide on dsl wiki (http://www.damnsmalllinux.org/wiki/index.php/Install_to_USB_From_within_Linux). The bios doesn't have a setting for booting from usb. Grub doesn't "see" the usb drive when I use the root and find commands, explained in (http://www.damnsmalllinux.org/wiki/index.php/USB_Booting). This happens even when I set boot from floppy at the top of the boot order. However, my usb keyboard is recognised by the bios and by grub. How can it recognise the keyboard but not the usb drive? Also, the usb led does flash even before grub starts up, so surely something must be happening usb-wise? I am now following an ubuntu guide to booting from a USB stick, using a hdd-based, minimal linux kernel to supply the usb drivers. But I'm having difficulty adapting it to other OSes (slax/dsl/aptosid). I believe I have to alter the initrd.gz file to include usb drivers and then copy that file along with vmlinuz to a partition on my hdd. But, what's the grub command for the kernel line supposed to look like? From the ubuntu example it's: title USB FLASH DRIVE root (hd0,6) kernel /boot/usb-boot/vmlinuz file=/cdrom/preseed/ubuntu.seed boot=casper noprompt cdrom-detect/try-usb=true persistent initrd /boot/usb-boot/initrd.lz boot Should mine just be: title USB FLASH DRIVE root (hd0,6) kernel /boot/usb-boot/vmlinuz cdrom-detect/try-usb=true initrd /boot/usb-boot/initrd.lz boot

  Read the article

• Running WAMP (XAMPP) and LAMP from One SSD, On 64-bit Windows and Linux Machines

  - by nicorellius

  I have an solid state drive that I develop websites on. The reason I do this is because I work on a few different computers. Historically, I created separate developing environments to use for each machine. This was OK, but if the system changed for some reason, eg, new OS install, it was a pain. So I bought a USB 3.0 enclosure and put a solid state drive in there and it's pretty darn fast, which is good. I was working with three Windows machines and I could simply hook up the drive, launch my XAMPP server and away I went, developing websites: using Dreamweaver, Komodo, Notepad++, Eclipse, etc. Recently, however, one of my Windows machines' hard drive went down and instead of going back to Windows in this case, I went with Ububntu 12.04. I have several Ubuntu workstations and servers and I like Linux, so I thought his was a great opportunity to transition. I went to work installing and trying to set up a LAMP server and, besides from XAMPP 64-bit compatibility out of the box, I'm seeing other issues with getting this Linux server running. I will keep trying to resolve this, but in the meantime... my question is, has anyone ever successfully run both WAMP and LAMP from the same SSD (formatted to NTFS)? I'm sure there are lots of barriers to this happening, like local file system, OS libraries, dependencies, etc. But I was thinking it would be cool if it could be done. I'm no expert, so if this is just plain old stupid, please don't hesitate to let me know.

  Read the article

• Looking for advice on using dd to backup a dual boot laptop.

  - by AvatarOfChronos

  My questions boils down to this. If I do "dd if=/dev/sda of=usbdrive" can anybody confirm that this will get everything including mbr/partition information/all four partitions and create a drive that I can swap with the failing internal drive without losing anything? If this is done while the computer is running will it still copy everything? At this point I'm afraid to shutdown the computer for fear of it never starting again. Secondly, how tolerant is dd of failing drives? Has anybody used it to recover a half dead drive before that can share any potential pitfalls? Did it get the data ok or is this going to be a hope for the best kind of situation? And lastly, If the usbdrive is larger than the failing internal drive I'll still be able to expand the partitions later so I'm not losing space? this last part seems silly to ask but with my current streak of bad luck I'll end up overwriting some magic bit and forever turning a 640gb hdd into a 500gb hdd. Also if anybody has a better solution to create a complete clone that gets everything I'm all for hearing about it. PostScript: I had been making periodic backups however when whatever miasma that killed the laptop struck it also got the NAS :( Post PostScript: both devices were on a UPS system.

  Read the article

• One Way Sync with Dropbox?

  - by user244805

  Is there any way I can mirror a dropbox folder to my C drive by just running a portable file? Extra background information because I know you guys hate it when you don't get the entire situation: I go back to University in fall and I need a new storage solution. I decided to use DropBox to sync my tiny University files (< 5 MB). I need to access these files from 4 machines: Windows 7 Home machine Windows 7 University A machine Windows 7 University B machine Android tablet 1 and 4 are a non-issue. The problem lies with 2 and 3. I want to be able to edit my files on 2 and 3 but those machines are not mine. There is an easy fix. Run a portable version of the DropBox syncer on a USB drive. But the problem is that I don't want to carry a USB drive around with me all the time. In that case, I can just run the small portable DropBox syncer off the internet. But where will it to store the files? A temporary directory on the C drive. There is only one issue left: there are hundreds of machines that I will randomly use that fit in categories 2 and 3. My portable DropBox syncer will notice that the temporary directory is empty on each new PC I use and instead of downloading my DropBox folder to the machine, it syncs the other way around i.e. it deletes my entire DropBox. The solution is to mirror my DropBox onto the temporary directory before running the DropBox syncer.

  Read the article

• Windows won't boot after moving house. How do I solve this?

  - by James

  Ive just moved house and tried to set up my desktop after packing it away and now when I power it on, the BIOS boots up and no errors are found but when my computer tires to boot into Windows 7 a continuous fast beeping sound is made and a black screen is displayed. What I've done so far: Reset to UEFI defauts Played about with RAM, I had 4*4 GB sticks, I took all of them out to test for a mobo error which I have and now im only using 1 stick of 4 GB. Changed my GPU, I tok my gtx580 out and now im using the onboard Intel 3000 graphics driver, the BIOS and uefi are correctly displaying so I no longer think its a GPU based error. Ive check all of the connections and nothing seems to be loose. My HDD setup is: 2 128 GB SSD's in Raid 0 as my main C drive (possibly cause of error?) 1 1 TB Games drive 1 2 TB Data Drive Ive also got a blueray drive connected. After searching the internet im pretty much out of suggestions but im currently downloading a live CD to see if it will boot and if I can access some files on my HDD.

  Read the article

• NAS for Mac OS X Server

  - by SamAdmin

  I'm using Mac OS X Server and want to allow the users that connect to their network accounts to store their data on a NAS drive. I want the users to connect to the Lion server as this allows for better policies and management for me and for their afp share to be located on a NAS drive. I've looked into home directories and network logins however I don't want the users to connect into a different login environment, just an authentication against their provided account on the Lion server and for their finder to take them to their own storage area - located on the NAS drive. Currently I am using FreeNAS for both authentication and storage however there are getting to be far too many people to manage each afp share and account, plus just using FreeNAS is extremely limiting for expansion and if something goes wrong with 1 entity the entire system goes down. Using the Lion server for user accounts and policies will be much better for this expanding business. I have looked into LDAP, using the Lion server as an LDAP server to authenticate against for FreeNAS however I have had issues with this and thought a different approach could be better from the other side of the situation... Providing the account with somewhere to store data rather than the afp share authenticating against an LDAP server. I am wrong to try it this way? Is it possible to logically add storage to a Mac OS X Server which can be recognised as a local drive, so can be used for network accounts?

  Read the article

• How to copy VirtualBox VDI contents to a partition and dual boot the OS from it?

  - by Calmarius

  I'm a Linux user but I keep a compressed Windows XP ISO with me on a pen drive for the case I absolutely need Windows to do something. This works in VirtualBox most of the time. But now I want to play some games, so I would like to run the Windows image natively. My computer don't have CD drive so cannot just burn the ISO and make an install normally. What I trying to do is moving the installed Windows image to a physical NTFS partition on my HDD and set up GRUB to let me dual boot it. I found many tutorials that deal with making VDI to physical drive. But they assume I want to overwrite my entire drive. Moving the raw disk image with dd to the partition resulted in a corrupt partition. I also tried the VMDK trick to use that empty partition and install the Windows on it. Although the text mode phase of the installation finishes without problems, the VM won't work, either crashes and keeps rebooting or just immediately or freezes (depending on how I created the VMDK, with -rawdisk /dev/sda3 or -rawdisk /dev/sda -partition 3).

  Read the article

• Blue screen of Death on Install

  - by Toby Allen

  I have a machine with Windows Vista Installed. It has an Intel X25 SSD as the System Drive I want to reinstall (I plan to format and overwrite Vista) with XP. When I boot up using the Dell XP CD it loads the initial drivers then i get a Blue Screen. This is quite concerning. The installed OS works ok, but its giving problems so I want to remove it. Should I just format the SSD and try again? Will this make any difference? Can I do something to avoid hitting the Blue Screen? Its possible I had corrupt sectors on one of the other disks, will a new XP install use the System drive or drive 0? Can I force the install to use a specific drive when installing? Error: *** STOP: 0x0000007B (0xF78D2524,0x0000034,0x00000000,0x00000000) I never did find the answer, however I removed the SSD and tried to install on other disk - CRASH I disconnected the other disk and tried to install with only SSD plugged in - CRASH I removed 1 block of RAM - CRASH I used a windows 7 CD - NO CRASH

  Read the article

• How to fix UNMOUNTABLE_BOOT_VOLUME (0x000000ED) on my Windows XP DELL laptop?

  - by Neil

  I have a Dell Latitude D410. Running Windows XP. I am receiving the STOP: 0x000000ED (0X899CF030,0XC0000185,0X00000000,0X00000000) Blue screen. Initially, I tried everything specified with the Microsoft KB articles. At this time, I was able to boot into the general safemode. I pulled the hard drive and was able to run chkdsk on it- it noted that it had fixed some errors, but I was still unable to boot. I put a brand new hard drive in the laptop. Windows XP installation worked up until the reboot, at which time the exact same error message came back up. What I have tried (all since the new hard drive was installed): chkdsk /R All suggested solutions in Microsoft KB articles Reseating RAM Opened laptop, reseated all connectors, looked for signs of damage (saw none) Reset BIOS options to default Ran the basic Dell diagnostics I have looked at the current entry:How can I boot XP after receiving stop error 0x000000ED - I am currently in the process of downloading the Ultimate Boot CD to use as a test, but I am not holding out a lot of hope as I really doubt this brand new Hard Drive is bad. Can anyone think of other areas I am missing? Ran MEMTEST86+ V4.10 for 15 passes (overnight). 0 Errors EDIT: FORMATTING

  Read the article

• How can I get DVDs playing after a Vista to XP change?

  - by Liath

  I replaced my vista install on a Dell Inspiron 1525 with XP and have managed to get most things up and running again however I'm having trouble with playing DVDs. When I try and play a DVD I get the following message: Windows Media Player cannot play this DVD because there is a problem with digital copy protection between your DVD drive, decoder, and video card. Try installing an updated driver for your video card. I have ensured that my drive is configured to play Region 2 discs (I'm in the UK), I've installed the most up to date XP codec pack which makes me think it's a driver issue. In device manager I have got my DVD drivers up to date however under "Other Devices" I'm missing several which sound key: Audio Device on High Definition Audio Bus Modem Device on High Definition Audio Bus Video Controller Video Controller (VGA Compatible) However I've installed all the relevant drivers I can find on the Dell website. The drive itself is working - I've run software from the drive. I'm afraid I am far from a sys-admin so I'm struggling on this one. How can I get my DVDs playing again?

  Read the article

• How to copy a floppy boot disk?

  - by Sammy

  I have a floppy boot disk and I would like to copy it to preserve it, as a backup. If I have two floppy drives, A and B, how can I copy the disk? Assuming one has two floppy drives Can I simply insert the floppy disk in one of the drives and then an empty floppy disk in the other and issue a simple command like this one. A:\>copy . b: Will this only copy the contents of the current directory and none of the files in subdirectories? Do I have to explicitly specify the option to copy everything? Also, what about the boot information? That won't get copied, right? If one has only one floppy drive... How do you copy a floppy disk if you only have one floppy drive? Do you in fact have to copy its contents to the local hard drive C and then copy that to an empty floppy disk using the same floppy drive? A:\>copy . c:\floppydisk A:\> A:\>c: C:\> C:\>copy floppydisk a: C:\> I'm guessing I will need some type of disk image tool to really copy everything on a bootable floppy disk. Something like the dd command on Linux perhaps? Am I right?

  Read the article

• Can't create system image. 0x80780119 error after upgrade from 8 to 8.1

  - by cichy202

  I have upgraded my Windows 8 PC to 8.1 yesterday and it seemed like everything is working fine until I tried to create System Image. I got an error 0x80780119 saying that there is to little space on one of the partitions. I started looking into this problem and indeed one of the partitions does not meet the requirements. There are following partitions on my drive: DISKPART> list partition Partition ### Type Size Offset ------------- ---------------- ------- ------- Partition 1 Recovery 300 MB 1024 KB Partition 2 System 100 MB 301 MB Partition 3 Reserved 128 MB 401 MB Partition 4 Primary 74 GB 529 MB Partition 5 Primary 390 GB 75 GB Partition 1 has only 13MB free space. Partition 2 has 70MB free space, partition 3 is MSFTRES, partition 4 is my C drive with around 35GB free and partition 5 is not included in system image. Partitions were create like this during installation of Windows 8 - clean install from scratch. I am using UEFI so the drive is GPT formatted. So I thought, OK I can resize my C drive a little, move the partitions and expand the 1st one. I tried using GParted but it is not able to move the MSFTRES partition. It does not recognize the file system on it. So the question is: Is it possible to "clean up" the 1st partition in anyway? If not, is there anything special about MSFTRES partition? Or can I just remove it and create it a little further and just flag it as msftres with GParted?

  Read the article

< Previous Page | 183 184 185 186 187 188 189 190 191 192 193 194  | Next Page >