Search Results

Search found 5885 results on 236 pages for 'finally'.

Page 188/236 | < Previous Page | 184 185 186 187 188 189 190 191 192 193 194 195  | Next Page >

• Neighbour table overflow on Linux hosts related to bridging and ipv6

  - by tim

  Note: I already have a workaround for this problem (as described below) so this is only a "want-to-know" question. I have a productive setup with around 50 hosts including blades running xen 4 and equallogics providing iscsi. All xen dom0s are almost plain Debian 5. The setup includes several bridges on every dom0 to support xen bridged networking. In total there are between 5 and 12 bridges on each dom0 servicing one vlan each. None of the hosts has routing enabled. At one point in time we moved one of the machines to a new hardware including a raid controller and so we installed an upstream 3.0.22/x86_64 kernel with xen patches. All other machines run debian xen-dom0-kernel. Since then we noticed on all hosts in the setup the following errors every ~2 minutes: [55888.881994] __ratelimit: 908 callbacks suppressed [55888.882221] Neighbour table overflow. [55888.882476] Neighbour table overflow. [55888.882732] Neighbour table overflow. [55888.883050] Neighbour table overflow. [55888.883307] Neighbour table overflow. [55888.883562] Neighbour table overflow. [55888.883859] Neighbour table overflow. [55888.884118] Neighbour table overflow. [55888.884373] Neighbour table overflow. [55888.884666] Neighbour table overflow. The arp table (arp -n) never showed more than around 20 entries on every machine. We tried the obvious tweaks and raised the /proc/sys/net/ipv4/neigh/default/gc_thresh* values. FInally to 16384 entries but no effect. Not even the interval of ~2 minutes changed which lead me to the conclusion that this is totally unrelated. tcpdump showed no uncommon ipv4 traffic on any interface. The only interesting finding from tcpdump were ipv6 packets bursting in like: 14:33:13.137668 IP6 fe80::216:3eff:fe1d:9d01 > ff02::1:ff1d:9d01: HBH ICMP6, multicast listener reportmax resp delay: 0 addr: ff02::1:ff1d:9d01, length 24 14:33:13.138061 IP6 fe80::216:3eff:fe1d:a8c1 > ff02::1:ff1d:a8c1: HBH ICMP6, multicast listener reportmax resp delay: 0 addr: ff02::1:ff1d:a8c1, length 24 14:33:13.138619 IP6 fe80::216:3eff:fe1d:bf81 > ff02::1:ff1d:bf81: HBH ICMP6, multicast listener reportmax resp delay: 0 addr: ff02::1:ff1d:bf81, length 24 14:33:13.138974 IP6 fe80::216:3eff:fe1d:eb41 > ff02::1:ff1d:eb41: HBH ICMP6, multicast listener reportmax resp delay: 0 addr: ff02::1:ff1d:eb41, length 24 which placed the idea in my mind that the problem maybe related to ipv6, since we have no ipv6 services in this setup. The only other hint was the coincidence of the host upgrade with the beginning of the problems. I powered down the host in question and the errors were gone. Then I subsequently took down the bridges on the host and when i took down (ifconfig down) one particularly bridge: br-vlan2159 Link encap:Ethernet HWaddr 00:26:b9:fb:16:2c inet6 addr: fe80::226:b9ff:fefb:162c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:120 errors:0 dropped:0 overruns:0 frame:0 TX packets:9 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:5286 (5.1 KiB) TX bytes:726 (726.0 B) eth0.2159 Link encap:Ethernet HWaddr 00:26:b9:fb:16:2c inet6 addr: fe80::226:b9ff:fefb:162c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1801 errors:0 dropped:0 overruns:0 frame:0 TX packets:20 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:126228 (123.2 KiB) TX bytes:1464 (1.4 KiB) bridge name bridge id STP enabled interfaces ... br-vlan2158 8000.0026b9fb162c no eth0.2158 br-vlan2159 8000.0026b9fb162c no eth0.2159 The errors went away again. As you can see the bridge holds no ipv4 address and it's only member is eth0.2159 so no traffic should cross it. Bridge and interface .2159 / .2157 / .2158 which are in all aspects identical apart from the vlan they are connected to had no effect when taken down. Now I disabled ipv6 on the entire host via sysctl net.ipv6.conf.all.disable_ipv6 and rebooted. After this even with bridge br-vlan2159 enabled no errors occur. Any ideas are welcome.

  Read the article

• Add a small RAID card? Will it help overall stability and performance of my nine hard drives?

  - by Ray

  Hi, Will I get any extra genuine added performance and RAID stability if I insert a basic RAID card into a PCI-E x1 slot? I am considering the Adaptec 1220SA - 2 port SATA , pci-express (1x) , raid 0/1. Ok it only supports two SATA drives. Purpose is to help support the eight internal hard drives (1TB each), a DVD drive and an external e-SATA connected 2TB hard drive - by dealing with two of the internal hard drives. My current configuration of eight internal 1TB Barracuda (7200.12) SATA hard drives, one external 2TB SATA Western Digital Green Drive (e-SATA) and one DVD drive can already be supported by the Intel P55 & JMicron controllers on the ASUS motherboard : the Intel P55 (controls six HDD; configured as three x RAID 1), and the JMicron (controls two HDD as one RAID 1, as well as the DVD drive and the external SATA drive via the motherboard's e-SATA port (controlled by the JMicron)). Bigger picture details : I have an ASUS motherboard designed for the LGA1156 type processor and it includes the Intel P55 Express Chipset and JMicron. I am using the Intel Core i7-870 processor, and have 8GB DDR3 (1333) memory (four x 2GB Corsair DIMMs). Enough overall power. The power supply is more than sufficicient for the system. Corsair AX850. The system will never need the full 850 watts (future : second graphics card). The RAID card would provide hardware RAID 1 for two of the eight intrnal drives. It would either reduce the load on : the Intel P55 firmware RAID support, or replace the JMicron controller's RAID 1 set. I am busy installing the above configuration using Windows 7 Ultimate 64-bit as the OS. The RAID card is a last minute addition to the plan. Is it worth spending the extra R700 - R900 on the Adaptec 1220SA, or equivalent RAID card? I cannot afford to spend yet another R2000 - R3000 on a RAID card that would support many SATA2 hard drives, with a better RAID, example the RAID 5. My Issue & assumption : I am trusting that the Intel P55 chipset can properly handle six drives, configured as three * RAID 1. I am assuming that the JMicron can handle, using its RED SATA ports, one RAID-1 (two HDDs). The DVD drive connects to the JMicron optical SATA port 1 (white port 1). White port 2 is not used. The e-SATA connection is from the JMicron straight to, and through the motherboard - to an on-board (rear panel) e-SATA port. Am I being a little hopeful in only using the on-board Intel P55 and the JMicron? Is it a waste of money to install a RAID card that handles two SATA2 drives? OR Is it wisdom to take the pressure a little off the Intel P55? Obviously I am interested in data security, hence RAID 1, not RAID Zero. RAID 5 would be nice. The CPU, Intel Core i7-870 will provide the clout. Context to nine drives : I am using virtualisation with Windows 7 Ultimate. Bootable VMs. The operating system gets a mirror. Loaded apps gets a mirror. The current design data is kept in another mirror and Another mirror is back-up one and / or VM territory. Then the external 2TB drive (via e-SATA) is the next layer of data security and then finally, I use off-site data security. Thanks.

  Read the article

• Performance issues when using SSD for a developer notebook (WAMP/LAMP stack)?

  - by András Szepesházi

  I'm a web application developer using my notebook as a standalone development environment (WAMP stack). I just switched from a Core2-duo Vista 32 bit notebook with 2Gb RAM and SATA HDD, to an i5-2520M Win7 64 bit with 4Gb RAM and 128 GB SDD (Corsair P3 128). My initial experience was what I expected, fast boot, quick load of all the applications (Eclipse takes now 5 seconds as opposed to 30s on my old notebook), overall great experience. Then I started to build up my development stack, both as LAMP (using VirtualBox with a debian guest) and WAMP (windows native apache + mysql + php). I wanted to compare those two. This still all worked great out, then I started to pull in my projects to these stacks. And here came the nasty surprise, one of those projects produced a lot worse response times than on my old notebook (that was true for both the VirtualBox and WAMP stack). Apache, php and mysql configurations were practically identical in all environments. I started to do a lot of benchmarking and profiling, and here is what I've found: All general benchmarks (Performance Test 7.0, HDTune Pro, wPrime2 and some more) gave a big advantage to the new notebook. Nothing surprising here. Disc specific tests showed that read/write operations peaked around 380M/160M for the SSD, and all the different sized block operations also performed very well. Started apache performance benchmarking with Apache Benchmark for a small static html file (10 concurrent threads, 500 iterations). Old notebook: min 47ms, median 111ms, max 156ms New WAMP stack: min 71ms, median 135ms, max 296ms New LAMP stack (in VirtualBox): min 6ms, median 46ms, max 175ms Right here I don't get why the native WAMP stack performed so bad, but at least the LAMP environment brought the expected speed. Apache performance measurement for non-cached php content. The php runs a loop of 1000 and generates sha1(uniqid()) inisde. Again, 10 concurrent threads, 500 iterations were used for the benchmark. Old notebook: min 0ms, median 39ms, max 218ms New WAMP stack: min 20ms, median 61ms, max 186ms New LAMP stack (in VirtualBox): min 124ms, median 704ms, max 2463ms What the hell? The new LAMP performed miserably, and even the new native WAMP was outperformed by the old notebook. php + mysql test. The test consists of connecting to a database and reading a single record form a table using INNER JOIN on 3 more (indexed) tables, repeated 100 times within a loop. Databases were identical. 10 concurrent threads, 100 iterations were used for the benchmark. Old notebook: min 1201ms, median 1734ms, max 3728ms New WAMP stack: min 367ms, median 675ms, max 1893ms New LAMP stack (in VirtualBox): min 1410ms, median 3659ms, max 5045ms And the same test with concurrency set to 1 (instead of 10): Old notebook: min 1201ms, median 1261ms, max 1357ms New WAMP stack: min 399ms, median 483ms, max 539ms New LAMP stack (in VirtualBox): min 285ms, median 348ms, max 444ms Strictly for my purposes, as I'm using a self contained development environment (= low concurrency) I could be satisfied with the second test's result. Though I have no idea why the VirtualBox environment performed so bad with higher concurrency. Finally I performed a test of including many php files. The application that I mentioned at the beginning, the one that was performing so bad, has a heavy bootstrap, loads hundreds of small library and configuration files while initializing. So this test does nothing else just includes about 100 files. Concurrency set to 1, 100 iterations: Old notebook: min 140ms, median 168ms, max 406ms New WAMP stack: min 434ms, median 488ms, max 604ms New LAMP stack (in VirtualBox): min 413ms, median 1040ms, max 1921ms Even if I consider that VirtualBox reached those files via shared folders, and that slows things down a bit, I still don't see how could the old notebook outperform so heavily both new configurations. And I think this is the real root of the slow performance, as the application uses even more includes, and the whole bootstrap will occur several times within a page request (for each ajax call, for example). To sum it up, here I am with a brand new high-performance notebook that loads the same page in 20 seconds, that my old notebook can do in 5-7 seconds. Needless to say, I'm not a very happy person right now. Why do you think I experience these poor performance values? What are my options to remedy this situation?

  Read the article

• Set up lnux box for hosting a-z

  - by microchasm

  I am in the process of reinstalling the OS on a machine that will be used to host a couple of apps for our business. The apps will be local only; access from external clients will be via vpn only. The prior setup used a hosting control panel (Plesk) for most of the admin, and I was looking at using another similar piece of software for the reinstall - but I figured I should finally learn how it all works. I can do most of the things the software would do for me, but am unclear on the symbiosis of it all. This is all an attempt to further distance myself from the land of Configuration Programmer/Programmer, if at all possible. I can't find a full walkthrough anywhere for what I'm looking for, so I thought I'd put up this question, and if people can help me on the way I will edit this with the answers, and document my progress/pitfalls. Hopefully someday this will help someone down the line. The details: CentOS 5.5 x86_64 httpd: Apache/2.2.3 mysql: 5.0.77 (to be upgraded) php: 5.1 (to be upgraded) The requirements: SECURITY!! Secure file transfer Secure client access (SSL Certs and CA) Secure data storage Virtualhosts/multiple subdomains Local email would be nice, but not critical The Steps: Download latest CentOS DVD-iso (torrent worked great for me). Install CentOS: While going through the install, I checked the Server Components option thinking I was going to be using another Plesk-like admin. In hindsight, considering I've decided to try to go my own way, this probably wasn't the best idea. Basic config: Setup users, networking/ip address etc. Yum update/upgrade. Upgrade PHP: To upgrade PHP to the latest version, I had to look to another repo outside CentOS. IUS looks great and I'm happy I found it! cd /tmp #wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/epel-release-1-1.ius.el5.noarch.rpm #rpm -Uvh epel-release-1-1.ius.el5.noarch.rpm #wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/ius-release-1-4.ius.el5.noarch.rpm #rpm -Uvh ius-release-1-4.ius.el5.noarch.rpm yum list | grep -w \.ius\. [will list all packages available in the IUS repo] rpm -qa | grep php [will list installed packages needed to be removed. the installed packages need to be removed before you can install the IUS packages otherwise there will be conflicts] #yum shell >remove php-gd php-cli php-odbc php-mbstring php-pdo php php-xml php-common php-ldap php-mysql php-imap Setting up Remove Process >install php53 php53-mcrypt php53-mysql php53-cli php53-common php53-ldap php53-imap php53-devel >transaction solve >transaction run Leaving Shell #php -v PHP 5.3.2 (cli) (built: Apr 6 2010 18:13:45) This process removes the old version of PHP and installs the latest. To upgrade mysql: Pretty much the same process as above with PHP #/etc/init.d/mysqld stop [OK] rpm -qa | grep mysql [installed mysql packages] #yum shell >remove mysql mysql-server Setting up Remove Process >install mysql51 mysql51-server mysql51-devel >transaction solve >transaction run Leaving Shell #service mysqld start [OK] #mysql -v Server version: 5.1.42-ius Distributed by The IUS Community Project The above upgrade instructions courtesy of IUS wiki: http://wiki.iuscommunity.org/Doc/ClientUsageGuide Create a chroot jail to hold sftp user via rssh. This will force SCP/SFTP and will circumvent traditional FTP server setup. #cd /tmp #wget http://dag.wieers.com/rpm/packages/rssh/rssh-2.3.2-1.2.el5.rf.x86_64.rpm #rpm -ivh rssh-2.3.2-1.2.el5.rf.x86_64.rpm #useradd -m -d /home/dev -s /usr/bin/rssh dev #passwd dev Edit /etc/rssh.conf to grant access to SFTP to rssh users. #vi /etc/rssh.conf Uncomment line allowscp This allows me to connect to the machine via SFTP protocol in Transmit (my FTP program of choice; I'm sure it's similar with other FTP apps). Above instructions for SFTP appropriated (with appreciation!) from http://www.cyberciti.biz/tips/linux-unix-restrict-shell-access-with-rssh.html And this is where I'm at. I will keep editing this as I make progress. Any tips on how to Configure virtual interfaces/ip based virtual hosts for SSL, setting up a CA, or anything else would be appreciated.

  Read the article

• Cheapest way to connect 20-24 Sata II HDDs in a budget storage server?

  - by Joe Hopfgartner

  I need to assemble a high density storage server for as cheap as possible. It's been a while for me and the last systems I integrated didn't even have Sata yet... During my Research I of course stumbled about Nexsan SATA Beast, the BackBlaze storage Pods as well as some ridiculously overpriced HP Proliant or Dell storage solutions. Finally I choose Norco cases as the way to go. My eye is set on the RPC-4020, which is a 4U 19" Rackmount case with 20 Hot Swap 3.5" SATA/SAS Hdd trays (Backplanes included) and room for two 2.5" OS drives as well as a Slim Line CD-Rom. The backplanes connect with a single SATA port for each drive, so there are 20 internal SATA ports to to be connected. They also have redundant power ports which I think is quite nice. The cheapest price I have found is 290$ + 40$ shipping. In europe the cheapest unfortunately is 370€ (500$) + 40 € shipping... A nice alternative would be the RPC-4224 which has SFF-8087 Mini SAS connectors that bundle 4 SATA trays each. But it doesn't seem to be available in Europe (where i am) anywhere. So here comes my problem: What Mainboard/Controller to choose to connect them for as cheap as possible while still having nice data rates? I have to say that the server is intended as a Storage server with 1gps connectivity and the data transfer will be distributed very evenly across all drives. I also don't require any raid functionality. This is all done at application level, I just need JBOD. So for example if I go for the RPC 4020 Model I need to connect 20 Storage + 1 OS + 1 CDROM Sata ports. I searched a bit and stumbled across this very low priced controller: http://www.intel.com/products/server/raid-controllers/SASWT4I/SASWT4I-overview.htm They sell it for 115 € here and the specs say it can control up to 122 hard discs and has 4 Mini SAS connectors. So I would use 4 Mini SAS 36pin - 4 SATA 7pin cables to connect 4 SATA drives to each port and choose a Mainboard taht has 6 SATA on board (for example this one) and hurray, I can connect my 22 SATA devices for as low as about ~ 220 EUR (cpu, ram, psu, case not counted) Question: WOULD THAT WORK? And if not, why? 2nd Question: If I go for the 4220 or 4224 Model, I have internal Mini SAS connectors. Am I right in assuming that the backplane than acts as a "SAS Expander"? And can I just plug these SAS connectors into any SAS port I can find on my controller / mainboard or are there certain requirements? I know that SATA port multipliers only work with controllers that are ready for that. But isn't this expansion already implemented in the SAS standard? I am sorry that this is a very broad question, but I really spent the last week reading up and it seems to be not so clear! Especially all the controlling hardware specifications! 3rd Question: A lot of hardware specs feature "internal channels" and "internal connectors". The connecors are the physical numbers of places where I can plug a cable in. I got that. But are the "internal channels" always the maximum numbers of physical drives that can be used in the end? Or can I enhance this further by Expanders/Fanouts? 4th and last question: What do you think about the setup so far? Do you know any good alternatives? Maby I am completely going the wrong way and some DAS would be way better? Are there any comparable chassis available in europe? Please feel free to say whatever you think is relevant to the subject!

  Read the article

• IP Micro-outages, telephone micro-outages, and CATV micro-outages

  - by Michael Graff

  This is a long and complicated question, mostly because it has been going on for 2.5 years without a solution in sight. It also is only one-third computer related, the other two-thirds are cable TV and cable-phone related. Background I have COX Communications for a cable provider, and we get Internet, digital cable TV, and digital phone service through them. The Internet is a SB5101 right now, and has been a DPC2100 and SB5120 in the past. Same results. The phone service is provided through a telephone interface mounted on the outside of the house (not classic VoIP) and the CATV is through a Scientific Atlanta receiver without DVR. I do have a TiVo connected to the CATV box. Symptoms The CATV shows "blocking" -- sometimes very very short duration where a few blocks appear on the screen. Sometimes it lasts long enough that the video "pauses" for 2-5 seconds, and rarely but not unseen the audio also fails. The CATV decoder box shows no correctable (FEC) or uncorrectable errors. That is, all BER counters are zero for the video stream. The Internet shows "micro-outages" where it appears that sent packets are not making it out, but I continue to receive packets from local modems. That is, pings stop coming back, but I continue to see modems broadcast for DHCP, and sometimes they ask more than once. The cable modem shows no errors during this time, but cable modems lie like you would not believe. It is actually possible to unplug the coax from the modem for 20 seconds and it reports NO ERRORS to the provider's tools. The phone service cuts out for 1-3 seconds, infrequently. When this happens, I hear NOTHING (not even comfort noise) and the remote side hears a "click" as if I were getting a call waiting message. However, there is no call incoming, other than the one I'm currently on of course. Things SEEM to happen more frequently when the temperature outside swings from cold to warm, so fall/spring seems worse than summer/winter. All micro-outages occur between once or twice a day (which I could ignore) to 10 times per hour. All SNR, signal levels, noise levels, etc. show very close to optimal when measured. COX's diagnosis This is a continual pain for me. Over the last 2.5 years, they have opened, "fixed" something, and closed the tickets. They close it without confirming that it is indeed better, and when I reopen they cannot do that, but instead they open a new ticket and send yet another low-level tech out to do the same signal tests and report that all is OK. I've finally gotten a line tech who has a clue and is motivated enough to pursue this with me. We have tried things like switching the local nodes over to UPS and generator power, but this does not trigger the noise. We have tried replacing all cabling, the tap outside my house, the modem, the CATV decoder -- all without resolution. Recently they have decided it is both my computer or switch, my TiVo, and my phone that are all broken and causing this issue. My debugging steps I spent the worse day of my TV-watching life yesterday and part of today. I watched live TV without the TiVo. I witnessed blocking, but it did "feel different." and was actually more severe. Some days it is better, some days it is worse, so perhaps this was just a very bad day. Today, I connected the TiVo to my DVD player, and ran two very long movies through it. I saw no blocking at all during nearly 6 hours of video. Suggestions? Does anyone have any suggestions on what to do next? I understand perhaps only the IP side can be addressed here, but it is one of the more limiting debugging options.

  Read the article

• Exchange Mail Flow

  - by Tuck918

  Hello. I have a question. We have one Exchange 2003 server and two Exchange 2007 servers. Most all of our mailboxes are on 2007 but we do still have one shared mailbox, unity mailbox and a journling mailbox on 2003. Public Folders have been set to replicate to 2007. I have set up a send connector on 2007 with a cost of 1. Receive connectors have Anonymous Users checked on 2007. On 2003 there are two connectors: the Internet Email connector and the connector that connects 2003 to 2007. We have a SPAM filtering device that email goes through before it is handed off to Exchange. The SPAM filtering device is set to send email to one of our Exchange 2007 servers. Here is my question/problem: Even though the SPAM filtering device is set to forward email to Exchange 2007, somehow all of our email is still going through the Exchange 2003 server before it finally hits the users mailboxes on the Exchange 2007 server. How can I change it so that all email goes directly to Exchange 2007 and never routes through Excahnge 2003 both ways, inbound and outbound? Would also like to add: In the EMC under Org- Hub- Send Connector there are two connectors. One is the "Internet Connector" from the 2003 box and the other is the new one I created. THe address space on the 2003 one is set to a cost of 2, no smart hosts and the 2003 box is listed as the Source Server. THe other Send Connector has an address space of 1, no smart host and has the 2 excahnge 2007 servers listed as the source servers. In EMC under Server- Hub- my two exchange 2007 servers are listed. Each one has 2 receive connectors. Both Recieve Connectors are setup the same way. THe Default Receive Connector has Anonymous Users checked. The other Recieve Connector is labled "Client" and I am not sure what it does or why its there. Anonymous Users are not checked. No smart hosts configured on 2003. Additional details Currently we have 3 excahnge servers. One exchange 2003 server and two excahnge 2007 servers. THe exchange 2003 server is the acting "bridgehead" serverand all email is routing through this server, inbound and outbound. We are wanting to decommission this server and use our two exchange 2007 servers as our mailbox servers. All of of user mailboxes are already on one of the exchange 2007 boxes and we want to put whats left on the exchange 2003 box on our other excahnge 2007 box. Both excahnge 2007 servers are currently CAS, HT and MB servers. We have a SPAM filtering device that sits between our excahnge servers and the firewall and have it configured to send messages to one of the excahgne 2007 servers but when we look at the message headers we can see that messgaes are still being routed to the excahnge 2003 box. We want to bypass the exchange 2003 in the routing process as it is dying and is starting to have major issues so everytime it goes down our email is down. Is there possible some sort of AD routing link/site link stuff going on?

  Read the article

• Apache access.log interpretation

  - by Pantelis Sopasakis

  In the log file of apache (access.log) I find log entries like the following: 10.20.30.40 - - [18/Mar/2011:02:12:44 +0200] "GET /index.php HTTP/1.1" 404 505 "-" "Opera/9.80 (Windows NT 6.1; U; en) Presto/2.7.62 Version/11.01" Whose meaning is clear: The client with IP 10.20.30.40 applied a GET HTTP method on /index.php (that is to say http://mysite.org/index.php) receiving a status code 404 using Opera as client/browser. What I don't understand is entries like the following: 174.34.231.19 - - [18/Mar/2011:02:24:56 +0200] "GET http://www.siasatema.com HTTP/1.1" 200 469 "-" "Python-urllib/2.4" So here what I see is that someone (client with IP 174.34.231.19) accessed http://www.siasatema.com and got a 200 HTTP status code(?). It doesn't make sense to me... the only interpretation I can think of is that my apache server acts like proxy! Here are some other requests that don't have my site as destination... 187.35.50.61 - - [18/Mar/2011:01:28:20 +0200] "POST http://72.26.198.222:80/log/normal/ HTTP/1.0" 404 491 "-" "Octoshape-sua/1010120" 87.117.203.177 - - [18/Mar/2011:01:29:59 +0200] "CONNECT 64.12.244.203:80 HTTP/1.0" 405 556 "-" "-" 87.117.203.177 - - [18/Mar/2011:01:29:59 +0200] "open 64.12.244.203 80" 400 506 "-" "-" 87.117.203.177 - - [18/Mar/2011:01:30:04 +0200] "telnet 64.12.244.203 80" 400 506 "-" "-" 87.117.203.177 - - [18/Mar/2011:01:30:09 +0200] "64.12.244.203 80" 400 301 "-" "-" I believe that all these are related to some kind of attack or abuse of the server. Could someone explain to may what is going on and how to cope with this situation? Update 1: I disabled mod_proxy to make sure that I don't have an open proxy: # a2dismod proxy Where from I got the message: Module proxy already disabled I made sure that there is no file proxy.conf under $APACHE/mods-enabled. Finally, I set on my browser (Mozzila) my IP as a proxy and tried to access http://google.com. I was not redirected to google.com but instead my web page appeared. The same happened with trying to access http://a.b (!). So my server does not really work as a proxy since it does not forward the requests... But I think it would be better if somehow I could configure it to return a status code 403. Here is my apache configuration file: <VirtualHost *:80> ServerName mysite.org ServerAdmin webmaster@localhost DocumentRoot /var/www/ <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/> Options Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog /var/log/apache2/error.log LogLevel warn CustomLog /var/log/apache2/access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> </VirtualHost> Update 2: Using a block, I restrict the use of other methods than GET and POST... <Limit POST PUT CONNECT HEAD OPTIONS DELETE PATCH PROPFIND PROPPATCH MKCOL COPY MOVE LOCK UNLOCK> Order deny,allow Deny from all </Limit> <LimitExcept GET> Order deny,allow Deny from all </LimitExcept> Now methods other that GET are forbidden (403). My only question now is whether there is some trick to boot those how try to use my server as a proxy out...

  Read the article

• How to Eliminate Tape Backup and Off-site Storage Service?

  - by Daniel Lucas

  PLEASE READ UPDATE AT THE BOTTOM. THANKS! ;) Environment Info (all Windows): 2 sites 30 servers site #1 (3TB of backup data) 5 servers site #2 (1TB of backup data) MPLS backbone tunnel connecting site #1 and site #2 Current Backup Process: Online Backup (disk-to-disk) Site #1 has a server running Symantec Backup Exec 12.5 with four 1TB USB 2.0 disks. BE jobs for full backups run nightly on all servers in site #1 to these disks. Site #2 backs up to a central file server there using software they already had when we purchased them. A BE job pulls that data nightly to site #1 and stores them on said disks. Off-site Backup (tape) Connected to our backup server is a tape drive. BE backs up the external disks to tape once a week which gets picked up by our off-site storage company. Obviously we rotate two tape libraries, one is always here and one is always there. Requirements: Eliminate the need for tape and off-site storage service by doing disk-to-disk at each site and replicating site #1 to site #2 and vice versa. Software based solution as hardware options have been too pricey (ie, SonicWall, Arkeia). Agents for Exchange, SharePoint, and SQL. Some Ideas So Far: Storage DroboPro at each site with an initial 8TB of storage (these are expandable up to 16TB at present). I like these because they are rackmountable, allow disparate drives, and have iSCSI interfaces. They are relatively cheap too. Software Symantec Backup Exec 12.5 already has all the agents and licenses we need. I'd like to keep using it unless there is a better solution, similarly priced, that does everything BE does plus deduplication and replication. Server Because there is no more need for a SCSI adapter (for tape drive) we are going to virtualize our backup server as it is currently the only physical machine save for SQL boxes. Problems: When replicating between sites we want as little data as possible to go across the pipe. There is no deduplication or compression in what I have laid out here so far. The files being replicated are BE's virtual tape libraries from our disk-to-disk backup. Because of this each of those huge files will go across the wire every week because they change every day. And Finally, the Question: Is there any software out there that does deduplication, or at least compression, to handle just our site-to-site replication? Or, looking at our setup, is there any other solution that I am missing that might be cheaper, faster, better? Thanks. Sorry so long. UPDATE 2: I've set a bounty on this question to get it more attention. I'm looking for software that will handle replication of data between two sites using the least amount of data possible (either compression, deduplication, or some other method). Something similar to rsync would work but it needs to be native to Windows and not a port involving shenanigans to get up and running. Prefer a GUI based product and I don't mind shelling out a few bones if it works. Please, answers that meet the above criteria only. If you don't think one exists or if you think I'm being to restrictive keep it to yourself. If after seven days there is no answer at all, so be it. Thanks again everyone. UPDATE 2: I really appreciate everyone coming forward with suggestions. There is no way for me to try all of these before the bounty expires. For now I'm going to let this bounty run out and whoever has the most votes will get the 100 rep points. Thanks again!

  Read the article

• nginx server over https using up all available file handles (upd: infinite loop?)

  - by mmr

  Hi all, So I have an nginx server that's working over https with Sinatra. When I try to download a jnlp file in a configuration that works fine over Mongrel and http (no s), the nginx server fails to serve the file with a 504 error. Subsequent checking of the logs states that this error is due to overflowing the available number of file handles, ie, "24: too many open files". Running sudo lsof -p <nginx worker pid> gets me a huge list of files, all looking like: nginx 1771 nobody 11u IPv4 10867997 0t0 TCP localhost:44704->localhost:https (ESTABLISHED) nginx 1771 nobody 12u IPv4 10868113 0t0 TCP localhost:https->localhost:44704 (ESTABLISHED) nginx 1771 nobody 13u IPv4 10868114 0t0 TCP localhost:44705->localhost:https (ESTABLISHED) nginx 1771 nobody 14u IPv4 10868191 0t0 TCP localhost:https->localhost:44705 (ESTABLISHED) nginx 1771 nobody 15u IPv4 10868192 0t0 TCP localhost:44706->localhost:https (ESTABLISHED) nginx 1771 nobody 16u IPv4 10868255 0t0 TCP localhost:https->localhost:44706 (ESTABLISHED) nginx 1771 nobody 17u IPv4 10868256 0t0 TCP localhost:44707->localhost:https (ESTABLISHED) nginx 1771 nobody 18u IPv4 10868330 0t0 TCP localhost:https->localhost:44707 (ESTABLISHED) nginx 1771 nobody 19u IPv4 10868331 0t0 TCP localhost:44708->localhost:https (ESTABLISHED) nginx 1771 nobody 20u IPv4 10868434 0t0 TCP localhost:https->localhost:44708 (ESTABLISHED) Increasing the number of files that can be opened is no help, because then nginx just blows right past that limit. And no wonder, it looks like it's in some kind of loop to pull all available files. Any idea what's going on, and how to fix it? EDIT: nginx 0.7.63, ubuntu linux, sinatra 1.0 EDIT 2: Here's the offending code. It's sinatra serving jnlp, which I finally figured out: get '/uploader' do #read in the launch.jnlp file theJNLP = "" File.open("/launch.jnlp", "r+") do |file| while theTemp = file.gets theJNLP = theJNLP + theTemp end end content_type :jnlp theJNLP end If I serve this with Sinatra via Mongrel and http, everything works fine. If I serve this with Sinatra and nginx via https, I get the above error. All other parts of the website appear to be equivalent. EDIT: I have since upgraded to passenger 2.2.14, ruby 1.9.1, nginx 0.8.40, openssl 1.0.0a, and no change. EDIT: The culprit appears to be infinite redirects due to using SSL. I don't know how to fix this, other than hosting the jnlp file in the root directory of the server (which I'd rather not do, since it limits me to one jnlp-based app at a time). The relevant lines from nginx.conf: # HTTPS server # server { listen 443; server_name MyServer.org root /My/Root/Dir; passenger_enabled on; expires 1d; proxy_set_header X-FORWARDED_PROTO https; proxy_set_header X_FORWARDED_PROTO https;#the almighty google is not clear on which to use location /upload { proxy_pass https://127.0.0.1:443; } } The funny thing about this is, first, I was putting the jnlp into a directory called 'uploader', not 'upload', but that still appeared to trigger the problem, since that proxy_pass directive appeared in the logs. Second, again, moving the jnlp into root avoided the problem, because there wasn't any of this proxying due to ssl. So, how can I avoid the infinite proxy_pass loop in nginx?

  Read the article

• Hardware recommendations / parts list for a modern, quiet ZFS NAS box - 2011-Feb edition [closed]

  - by dandv

  I want to build some really reliable storage for my data, and it seems that ZFS is the only filesystem at the moment that does live checksumming. That rules out DroboPro, so I'm looking to building a quiet ZFS NAS that would start with 4 2TB or larger hard drives. I'd like this system to be very reliable and relatively future-proof for 2-3 years, so I'm willing to invest some $$$ and buy higher end components. I did see questions here and on other forums about low-cost servers, but I'm not looking for those. I'd be super happy to go for an off-the-shelf solution, but I haven't found one that's quiet. I started doing the research (summarized on my wiki), but I realized that it just gets too complicated for what I know as a software dude, and I'm entering the analysis paralysis area. At this point, I'm basically looking for a parts list for a configuration that will work (and is modern), and I know there are folks around here who are way more competent than me. I've built computers and am comfortable assembling one and messing with *nix; I can follow guides; I just want to end the decision process for the hardware and software configuration. What I've researched so far (not that these are very modern components): Case: I think I've settled on the Antec Twelve Hundred case because it cools well, is quiet, and simply has 12 bays that allow elastic mounting. The SilverStone Raven is its counter-candidate, but I find its construction quite odd. For the PSU, I'm torn between Antec CP-850 and Nexus RX-8500, but I did this research more than a year ago. The Nexus has a very uniform power profile, and I'd rather not have the Antec spin up and down based on load. On the other hand, I'm not sure how often my file server will draw more than 400W under use. For the hard drives, I've read that WD Black drives are actually WD RE3 with a software setting changed. I'd also like to buy different drive types, not just 4 WDs. Recommendations? Right now I have a 2TB Hitachi Deskstar 7K300. For the motherboard, CPU and RAM I have no idea, other than the RAM must be ECC. I already asked a question here about ECC RAM, but I was misguided and was looking for a motherboard that would support USB 3.0 as well. I've learned to go with eSATA, or worry about USB later. Then there's the (liquid) cooling, Wi-Fi card, and FreeBSD vs. OpenSolaris Express. Lastly, I'm wondering if I can make this PC into a media server by adding a Blu-ray drive and a good sound card. But support for Blu-Ray is spotty on Linux, and I don't know if Windows 7 on VirtualBox would get sufficient hardware access to output HDMI or SPDIFF signals. (Running OpenSolaris virtualized is not an option because of the reliability risk.) Then there are HDCP concerns. Suggestions on that would be appreciated as well, but I don't want us to get sidetracked. A specific shopping list on the core components would be great, so I can start ordering, and in the meantime educate myself with regards to the other issues. Finally, I think this could become a great FAQ for those technically inclined to build their own ZFS server, but confused by the dizzying array of options out there, and I promise to compile the results and share my experience building and benchmarking the server.

  Read the article

• Can I make my drives visible and change their partition type without losing my data?

  - by user165408

  I have made a lot of mistakes and now I cannot see my hard disk nor I can start my operating system on my laptop. All my passwords and important files on my hdd without any backup. I followed this course of action Changed my hard disk partitions to dynamic just for getting 5th partition. (1st mistake) Decreased partitions to 4 again. Backed up operating system from 4th to 3rd partition with Norton Ghost. Booted from a live CD for Windows XP. Formatted 4th partition and moved my all important data from 1st and 2nd partitions to the 4th partition. Deleted 1st and 2nd partitions and got 1 partition from half of empty space. So I have just 3 partitions and empty space between 1st and 2nd partitions. Tried to install Windows 8 to the first partition but it did not allow because it is dynamic. Also it did not allow to install to other partitions. Tried to install Windows XP to the 1st partition but it said if I continue I cannot use other drivers. Therefore I escaped from installing it. Booted from the Windows XP live CD then increased 1st partiton to less than 400mb of empty space. Therefore I thought it will be adjacent but it was shown as 2 partitions. In my computer I see just 3 drivers. Using Norton Ghost I recovered my OS to the 1st partition. (2nd mistake it was on 4th partition originally) Booted from a Windows XP live CD I tried to install bcdedit to the Windows XP live CD but it did not work. Then I tried to install EaseUS Partition Master Home Edition. It was installed with errors then I start it and it showed me an error like there is no hard disk. I looked to my PC and my drivers were not there. Booted from the Norton Ghost CD and it did not show me my drivers either, but before I was able to see them. I checked numbers of partition shown by the Norton Ghost utility and they are still have same numbers so I have to see my drivers but I cannot see them now. My hard disk is shown as extarnal dynamic now so I cannot see any drive in my PC in the live Windows XP. There are two options; first one is import extarnal disk and second one is convert disk to basic. Will they delete my data? I fear booting from CDs like Windows XP live CD, Norton Ghost CD, and the operating system CD/DVD, because they may overwrite a few MB their data to my data. These recover tools are already exist in Windows XP live CD by The Ultimate Boot CD for Windows. Can any of them help me? CompuAppa SwissKnife V3 DBXtract Disk Investigator Fab's AutoBackup 2.0 FileRecovery Floppy Repair Free Undelete Handy Recovery Recovery Manager Restorastion Restorastion Help File by UBCD4Win UnChk Unstoppable Copier Finally How can I make it so that my drives are visible again without losing my data? How can I convert my dynamic partitions to basic without losing my data?

  Read the article

• Pushing DNSSEC updates with offline keys

  - by eggyal

  In a non-professional capacity, I look after the DNS of some 18 domains: mostly personal/vanity domains for immediate family. I outsource the whole shebang to an inexpensive managed hosting provider with a web interface through which I manage the zones; since the provider also offers DNSSEC, I have successfully deployed that too. These domains are so unimportant that an attack targetted against them seems much less likely than a general compromise of my provider's systems, at which point the records of all their customers might be changed to misdirect traffic (perhaps with extremely long TTLs). DNSSEC could protect against such an attack, but only if the zone's private keys are not held by the hosting provider. So, I wonder: how can one keep DNSSEC private keys offline yet still transfer signed zones to an outsourced DNS host? The most obvious answer (to me, at least) is to run one's own shadow/hidden master (from which the provider can slave) and then copy offline-signed zonefiles to the master as required. The problem is that the only machine I (want to*) control is my personal laptop, which usually connects from a typical home ADSL (behind NAT over a dynamically-assigned IP address). Having them slave from that (e.g. with a very long Expiry time on the zone for periods when my laptop is offline/unavailable) would not only require a Dynamic DNS record from which they can slave (if indeed they can slave from a named host rather than a static IP address), but would also involve me running a DNS server on my laptop and opening both it and my home network up to the incoming zone transfer requests: not ideal. I would prefer a much more push-oriented design, whereby my laptop initiates transfer of offline-signed zonefiles/updates to the provider's servers. I looked into whether nsupdate could fit the bill: documentation is a little sketchy, but my testing (with BIND 9.7) suggests it can indeed update DNSSEC zones, but only where the server holds the keys to perform the zone signing; I have not found a way to have it take an update including the relevant RRSIG/NSEC/etc. records and have the server accept them. Is this a supported use-case? If not, I suspect the only solutions which could fit the bill will involve non-DNS-based transfer of the zone updates and would welcome recommendations that are supported by (hopefully inexpensive) hosting providers: SFTP/SCP? rsync? RDBMS replication? Proprietary API? Finally, what would be the practical implications of such a setup? Key rotation is jumping out at me as being an obvious difficulty, especially if my laptop is offline for extended periods. But the zones are extremely stable, so perhaps I could get away with long-lived ZSKs**...? * Whilst I could run a shadow/hidden master on e.g. an outsourced VPS, I dislike the overhead of having to secure / manage / monitor / maintain yet another system; not to mention the additional financial costs of so doing. ** Okay, this would enable a concerted attacker to replay outdated records—but the risk and impact of such are both tolerable in the case of these domains.

  Read the article

• Set up lnux box for hosting a-z [apache mysql php ssl]

  - by microchasm

  I am in the process of reinstalling the OS on a machine that will be used to host a couple of apps for our business. The apps will be local only; access from external clients will be via vpn only. The prior setup used a hosting control panel (Plesk) for most of the admin, and I was looking at using another similar piece of software for the reinstall - but I figured I should finally learn how it all works. I can do most of the things the software would do for me, but am unclear on the symbiosis of it all. This is all an attempt to further distance myself from the land of Configuration Programmer/Programmer, if at all possible. I can't find a full walkthrough anywhere for what I'm looking for, so I thought I'd put up this question, and if people can help me on the way I will edit this with the answers, and document my progress/pitfalls. Hopefully someday this will help someone down the line. The details: CentOS 5.5 x86_64 httpd: Apache/2.2.3 mysql: 5.0.77 (to be upgraded) php: 5.1 (to be upgraded) The requirements: SECURITY!! Secure file transfer Secure client access (SSL Certs and CA) Secure data storage Virtualhosts/multiple subdomains Local email would be nice, but not critical The Steps: Download latest CentOS DVD-iso (torrent worked great for me). Install CentOS: While going through the install, I checked the Server Components option thinking I was going to be using another Plesk-like admin. In hindsight, considering I've decided to try to go my own way, this probably wasn't the best idea. Basic config: Setup users, networking/ip address etc. Yum update/upgrade. Upgrade PHP: To upgrade PHP to the latest version, I had to look to another repo outside CentOS. IUS looks great and I'm happy I found it! cd /tmp #wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/epel-release-1-1.ius.el5.noarch.rpm #rpm -Uvh epel-release-1-1.ius.el5.noarch.rpm #wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/ius-release-1-4.ius.el5.noarch.rpm #rpm -Uvh ius-release-1-4.ius.el5.noarch.rpm yum list | grep -w \.ius\. [will list all packages available in the IUS repo] rpm -qa | grep php [will list installed packages needed to be removed. the installed packages need to be removed before you can install the IUS packages otherwise there will be conflicts] #yum shell >remove php-gd php-cli php-odbc php-mbstring php-pdo php php-xml php-common php-ldap php-mysql php-imap Setting up Remove Process >install php53 php53-mcrypt php53-mysql php53-cli php53-common php53-ldap php53-imap php53-devel >transaction solve >transaction run Leaving Shell #php -v PHP 5.3.2 (cli) (built: Apr 6 2010 18:13:45) This process removes the old version of PHP and installs the latest. To upgrade mysql: Pretty much the same process as above with PHP #/etc/init.d/mysqld stop [OK] rpm -qa | grep mysql [installed mysql packages] #yum shell >remove mysql mysql-server Setting up Remove Process >install mysql51 mysql51-server mysql51-devel >transaction solve >transaction run Leaving Shell #service mysqld start [OK] #mysql -v Server version: 5.1.42-ius Distributed by The IUS Community Project And this is where I'm at. I will keep editing this as I make progress. Any tips on how to Configure Virtualhosts for SSL, setting up a CA, setting up SFTP with openSSH, or anything else would be appreciated.

  Read the article

• Hosed Windows 7 permissons

  - by Anthony

  Here is the most interesting thing I've noticed since the problems started: If I go into a control panel/system module (in this case the Resource Monitor) that has a "Check Online" type option, Firefox (my default browser) opens right up without a problem. But if I just start Firefox from any shortcuts (start menu, desktop, etc), the Firefox process starts up (and the start menu icon starts glowing) only to end without notice a few seconds later. Possibly related: If I start up in Safe-Mode (w/o Networking, but haven't tried with yet), I can start up FF or Chrome just fine, but if I attempt to open Chrome normally, I get a permissions error. Opera and Safari seem to be okay (mostly). Safari crashes when I try to download any files. All of the above leads me to believe that some (but clearly not all) core files have messed up permissions. Or rather, that I no longer have permission. System still does, based on Firefox opening without fail when the system initiates it. I've run MS Forefront once in normal mode, Malwarebytes twice in normal mode and once in safe-mode. One trojan found and deleted, but the problem persists. Two other things worth mentioning: I accidentally duplicated my library... I thought I'd try to add the "Internet" folder to my start menu, next to music and downloads. The first advanced thing I tried was "create new library". I clearly misunderstood what this means. I thought it was a way to add virtual folders to the library (which I thought, in turn, would allow me to choose it as a link on the start menu), but instead it recreated my already existing user folder, AppData and all. I didn't notice this until today. Then I tried setting permissions for my User folder to full control, recursively... Confused but not giving up,I thought I could maybe create a shortcut to the NetHood folder manually, but instead got hit with an access denied error. So I tried to change the permission levels for all sub-folders to my user folder so that I had full control. I got several access denied errors along the way. At this point I gave up, went out, ended up caught in the rain and stuck on a friend's couch and showing up late for work the next day. Thanks for nothing, Microsoft. When I finally got home today (20 hours later), I noticed that Firefox was acting really strange. I tried opening Chrome to see if the problem was client side or server side, and instead got the above-mentioned "you don't have permission to open this program" alert. And I think that's the whole story. Oh, I also did a system restore, but not chose a point from this morning (an auto update), and it worked but the problem wasn't fixed. And then all the earlier restore points were gone. So the questions are: a) is there a way to set the admin and user privs back to "default"? b) would this, in anyone's expert opinion, fix the problems I'm having? c) how come being logged in as an admin isn't the same as being logged in with admin privs? It seems that half the time I have to do run as admin for fairy standard things because i'm being treated as me-theuser and not me-theadmin. Thanks for reading.

  Read the article

• How to save a ntfs partition which suddenly became empty

  - by SteveO

  One ntfs partition of my laptop was suddenly wiped out without any notice to me, when I rebooted from Windows 7 to Ubuntu 12.04 today. I am in need of help to save my files on that partition, which are important and unfortunately haven't been backed up yet. My laptop has two operating systems: Windows 7 and Ubuntu 12.04. with a ntfs partition shared between the two operating systems for storing some data files (109GB, about 97%of which has been used). I have almost always been using Ubuntu, but today I happened to have to work under Windows. Following is a record of what happened in the time order, numbering according to which operating system I was in at each stage. When I started into Windows 7, right before being able to log in, it took a while and two reboots to configure the Windows. I thought it was normal, since last time when I was using Windows two weeks ago, it took very long and several reboots to update Windows, since the last time I used Windows before then was in November last year. Then after finally being able to log in Windows 7, I installed Libre Office, MathType (I got it from http://dl.portablesoft.org/down/?id=2515, which I originally thought was a trial version, but later I learned was a cracked version and felt wrong. I made a copy of it at dropbox http://dl.dropbox.com/u/13029929/MathType_6.8_PortableSoft.rar, not for distributing it but to list it there just in case it will help to identify the problem), and MikTex. I then edited some .doc files in the ntfs partition under both Microsoft Office with MathType, and Libre Office. When I finished working under Windows and rebooted into Ubuntu, Ubuntu did some filesystem checking and reported that the ntfs partition was not able to be mounted. Then I rebooted again into Windows, and found that the ntfs partition had been emptied, i.e. all the data files were gone, and only one system file bootsqm.dat and one system directory System Volume Information were there, with their last updated time being the time when I first rebooted from Windows to Ubuntu (in fact, it is 4 hours in advanced than the actual time of that rebooting , see immediately below) Also I noticed that the time shown by Windows is not correct for my time zone (UTC-05:00) Eastern Time (US & Canada)), which is 4 hours in advance than the correct time (my current time is 3am, but the computer shows 7am). Same things happened when I rebooted into Ubuntu again: the ntfs has been emptied and left with only one Windows system file bootsqm.dat and one Windows system directory System Volume Information. the time shown by Ubuntu is 4 hours in advance than the correct time. I wonder what I can do to retrieve my data files back on the ntfs partition? If I am not able to do it myself, will some professionals be able to help me out? Thanks a lot! PS: I didn't think I did any thing that required emptying that partition. But there were quite some works I did during that stage right before the reboot from Windows to Ubuntu when the problem occured. Did I make any mis-operation?

  Read the article

• Hard drive write speed - finding a lighter antivirus?

  - by Shingetsu

  I recently have been getting a lot of system lag here (for example, the mouse and the display in general take about 15 seconds to react in the worst cases). After a lot of monitoring the resources, I found that the problem mainly happens when too much Disk I/O is being done. Three culprits have been identified: My browser had the highest write I/O with 35,000,000 I/O Write Bytes. Steam had the highest read I/O (when IDLE!!!) with 106,000,000 I/O Read Bytes. My antivirus (in both cases I will soon mention) was the runner up in both cases with: 30,000,000ish write and 80,000,000ish read. The first AV I had was Avast! which I had liked on my previous system. After noticing it taking so much I/O I switched to Panda (supposing it wouldn't use TOO much during idle phase). However it only used a bit less I/O. Just a lot less memory and cpu and somewhat more network. My browser at the moment is Maxthon 3 (which I like a lot). Before this I was running chrome which had similar data and much higher cpu when running in the background was enabled. I'm not going to be running steam all the time and there aren't many alternatives to it. I like my browser very much, but I AM willing to switch if there's an obvious problem (I'm in programming, however I'm not a very good sysadmin, especially not when it comes to windows). Finally, my system almost stops lagging when I turn off the antivirus (and preferably steam) (some remains but once in every 5-6 hours for a few seconds so it isn't a big problem). My question (has a few parts): Is it possible to configure steam to lower it's I/O usage? (and maybe network while we're at it?) Which antivirus (very preferably free) uses lowest I/O while idle (I leave PC alone during active scans so that isn't a problem). Is there an obvious problem with my current browser and, if so, is there a way to fix it or should I switch and, if so, to what? (P.S. I've been on FFox for some time too). Info on system: Windows 7 (32 bit T_T, I am getting a new one in a few months but I want to keep using system during that time though). Hard Drive (main) is a Raid0. (Also have an external 1TB one which contains steam (and steam alone). As such it doesn't get used by much anything other than steam and isn't a very large problem. However steam still uses some I/O of registry) CPU: Intel(R) Core(TM)2 CPU [email protected] RAM: 6GB (3.25GB usable) (this and CPU have little effect as shown in next section) Additional info: Memory usage during problematic times: 44% CPU usage during problematic times: 35% Page File: main drive: system managed. 1TB drive: none. The current system I'm using is about 6 years old and is mainly a place holder while I await the new one in a few months. Final words: this is my 1st post on Super User (this question wouldn't feel right on Stack Overflow where I usually stay). If it doesn't have it's place here please tell me. If anything is wrong with it, same. Edit Technically I'm looking for a live thread detection program with minimal IO usage. I already have good active scan capability: Kaspersky (the free scanner uses the paid database) and MalwareBytes. Edit 2 Noticed another one, it seems that windows media player has been using stuff even when off! Turning it off and restarting now. If the problem is fixed I'll tell you guys. The reason I didn't notice it before was because I didn't have resource manager in front of me at the MOMENT of the problem. Now I did and it was at the very top of the list!

  Read the article

• Cablemodem (SBG6580) firewall denying some outbound traffic? Why? Not configured [migrated]

  - by lairdb

  I finally got around to turning the syslog on for my cablemodem (Motorola Surfboard SBG6580) and I'm seeing about the expected amount of inbound attackage being blocked... 2014-05-30 21:59:02 Local0.Alert 192.168.111.1 May 31 04:58:56 2014 SYSLOG[0]: [Host 192.168.111.1] UDP 12.230.209.198,4500 --> 66.27.xx.xx,61459 DENY:Firewall interface [IP Fragmented Packet] attack 2014-05-30 21:59:02 Local0.Alert 192.168.111.1 May 31 04:58:56 2014 SYSLOG[0]: [Host 192.168.111.1] TCP 17.172.232.109,5223 --> 66.27.xx.xx,53814 DENY:Firewall interface access request 2014-05-30 21:59:02 Local0.Alert 192.168.111.1 May 31 04:58:57 2014 SYSLOG[0]: [Host 192.168.111.1] UDP 12.230.209.198,443 --> 66.27.xx.xx,53385 DENY: Firewall interface [IP Fragmented Packet] attack 2014-05-30 21:59:02 Local0.Alert 192.168.111.1 May 31 04:58:57 2014 SYSLOG[0]: [Host 192.168.111.1] UDP 12.230.209.198,4500 --> 66.27.xx.xx,61459 DENY:Firewall interface [IP Fragmented Packet] attack 2014-05-30 21:59:10 Local0.Alert 192.168.111.1 May 31 04:59:04 2014 SYSLOG[0]: [Host 192.168.111.1] UDP 12.230.209.198,443 --> 66.27.xx.xx,59960 DENY: Firewall interface [IP Fragmented Packet] attack 2014-05-30 21:59:10 Local0.Alert 192.168.111.1 May 31 04:59:04 2014 SYSLOG[0]: [Host 192.168.111.1] UDP 12.230.209.198,4500 --> 66.27.xx.xx,61459 DENY:Firewall interface [IP Fragmented Packet] attack ...and that's great. (Sad, but great.) But I'm also seeing a HUGE amount of what appears to be denied outbound connectivity: 2014-05-30 16:30:10 Local0.Alert 192.168.111.1 May 30 23:30:04 2014 SYSLOG[0]: [Host 192.168.111.1] TCP 192.168.111.100,58969 --> 38.81.66.127,443 DENY: Inbound or outbound access request 2014-05-30 16:30:10 Local0.Alert 192.168.111.1 May 30 23:30:04 2014 SYSLOG[0]: [Host 192.168.111.1] TCP 192.168.111.100,58969 --> 38.81.66.127,443 DENY: Inbound or outbound access request 2014-05-30 16:30:10 Local0.Alert 192.168.111.1 May 30 23:30:04 2014 SYSLOG[0]: [Host 192.168.111.1] TCP 192.168.111.100,58965 --> 162.222.41.13,443 DENY: Inbound or outbound access request 2014-05-30 16:30:10 Local0.Alert 192.168.111.1 May 30 23:30:04 2014 SYSLOG[0]: [Host 192.168.111.1] TCP 192.168.111.100,58965 --> 162.222.41.13,443 DENY: Inbound or outbound access request 2014-05-30 16:30:10 Local0.Alert 192.168.111.1 May 30 23:30:04 2014 SYSLOG[0]: [Host 192.168.111.1] TCP 192.168.111.100,58964 --> 38.81.66.179,443 DENY: Inbound or outbound access request 2014-05-30 16:30:10 Local0.Alert 192.168.111.1 May 30 23:30:04 2014 SYSLOG[0]: [Host 192.168.111.1] TCP 192.168.111.100,58964 --> 38.81.66.179,443 DENY: Inbound or outbound access request ...and Spot checking suggests that it's all legitimate traffic (Opening connections to CrashPlan, etc.), I have no restrictions configured in the modem; I don't see why it should be blocking anything. Am I misreading the log entry, and it's not actually being denied? (Seems unlikely.) Is the ISP (TWC) pushing deny tables that are not exposed in the UI? (Tinfoil hat too tight.) I'm confused. (The good news, such as it is, is that AFAIK I'm not experiencing any actual issues... but maybe I am; tough to tell.) Thanks.

  Read the article

• Windows 8 Stuck on Start Screen File Search

  - by baturayd

  I have been searching someone else having the same issue but I couldn't find any. Here is my problem: I'm using Windows 8 Pro with Media Center. File search screen does not close itself after I make a file search within start screen. It stuck on that screen. I can't go back to desktop, therefore, task manager is inaccessible. Only way to get out of it is to sign out. It also looks like non-operational. It doesn't give me any result at all. It's just a blank screen with "Files" title. It used to work perfectly. Things I have done before coming here: Safe mode minimal boot to ensure no other 3rd party software interferes. sfc haven't found any inconsistencies. Search index has been rebuild. Normal boot with all 3rd party services and start-up items disabled. System restore to a date that I know this feature was functional. And by the way, I have installed all updates released so far. I strongly used file search via start menu back in Windows 7. This is an absolute game changer for me. I'm curious what causes this. I'll do a "system refresh" if I can't fix this. I'm working on it, I'll keep this thread updated should I find any fix. First update: I just discovered that file search screen gets stuck if it's invoked by typing query directly in start screen. It doesn't get stuck if it's invoked from win + x menu. I was able to "escape" from stuck screen with invoking it again by win + x menu. After rebuilding search index again, search suggestions started to appear again but still there is no file search functionality. Second update: "Results for" expression appears only for a second near to "Files" title when search is initialized. Third update: As a last resort, I finally tried to do a "System Refresh" which has also failed to refresh by giving an error after waiting almost 20 minutes at 99%. (Seriously?) After cold boot it began to undo changes. After changes were reverted, I boot the machine without doing anything further and bingo! Search began acting normal again. This is a totally weird solution. It obviously fixed certain system files during failed refresh, and kept those changes untouched because they were supposed to be that way at the first place. I'll keep this thread alive should anyone comes with a more logical explanation. Forth update: After a windows update, search functionality again stopped responding. It happened after a system update for the first time. Now I have a pretty good suspicion about system update, though I have no solid proof of its involvement with this problem.

  Read the article

• Android - How do I load a contact Photo?

  - by PaulH

  I'm having trouble loading a photo for a contact in Android. I've googled for an answer, but so far have come up empty. Does anyone have an example of querying for a Contact, then loading the Photo? So, given a contactUri which comes from an Activity result called using startActivityForResult(new Intent(Intent.ACTION_PICK,ContactsContract.CommonDataKinds.Phone.CONTENT_URI),PICK_CONTACT_REQUEST) is: content://com.android.contacts/data/1557 The loadContact(..) works fine. However when I call the getPhoto(...) method, I get a null value for the photo InputStream. It is also confusing because the URI values are different. The contactPhotoUri evaluates to: content://com.android.contacts/contacts/1557 See the comments inline in the code below. class ContactAccessor { /** * Retrieves the contact information. */ public ContactInfo loadContact(ContentResolver contentResolver, Uri contactUri) { //contactUri --> content://com.android.contacts/data/1557 ContactInfo contactInfo = new ContactInfo(); // Load the display name for the specified person Cursor cursor = contentResolver.query(contactUri, new String[]{Contacts._ID, Contacts.DISPLAY_NAME, Phone.NUMBER, Contacts.PHOTO_ID}, null, null, null); try { if (cursor.moveToFirst()) { contactInfo.setId(cursor.getLong(0)); contactInfo.setDisplayName(cursor.getString(1)); contactInfo.setPhoneNumber(cursor.getString(2)); } } finally { cursor.close(); } return contactInfo; // <-- returns info for contact } public Bitmap getPhoto(ContentResolver contentResolver, Long contactId) { Uri contactPhotoUri = ContentUris.withAppendedId(Contacts.CONTENT_URI, contactId); // contactPhotoUri --> content://com.android.contacts/contacts/1557 InputStream photoDataStream = Contacts.openContactPhotoInputStream(contentResolver,contactPhotoUri); // <-- always null Bitmap photo = BitmapFactory.decodeStream(photoDataStream); return photo; } public class ContactInfo { private long id; private String displayName; private String phoneNumber; private Uri photoUri; public void setDisplayName(String displayName) { this.displayName = displayName; } public String getDisplayName() { return displayName; } public void setPhoneNumber(String phoneNumber) { this.phoneNumber = phoneNumber; } public String getPhoneNumber() { return phoneNumber; } public Uri getPhotoUri() { return this.photoUri; } public void setPhotoUri(Uri photoUri) { this.photoUri = photoUri; } public long getId() { return this.id; } public void setId(long id) { this.id = id; } } } Clearly, I'm doing something wrong here, but I can't seem to figure out what the problem is. Thanks.

  Read the article

• WPF Dynamic Layout with ItemsControl and Grid

  - by Jason Williams

  I am creating a WPF form. One of the requirements is that it have a sector-based layout so that a control can be explicitly placed in one of the sectors/cells. I have created a tic-tac-toe example below to convey my problem: There are two types and one base type: public class XMoveViewModel : MoveViewModel { } public class OMoveViewModel : MoveViewModel { } public class MoveViewModel { public int Row { get; set; } public int Column { get; set; } } The DataContext of the form is set to an instance of: public class MainViewModel : ViewModelBase { public MainViewModel() { Moves = new ObservableCollection<MoveViewModel>() { new XMoveViewModel() { Row = 0, Column = 0 }, new OMoveViewModel() { Row = 1, Column = 0 }, new XMoveViewModel() { Row = 1, Column = 1 }, new OMoveViewModel() { Row = 0, Column = 2 }, new XMoveViewModel() { Row = 2, Column = 2} }; } public ObservableCollection<MoveViewModel> Moves { get; set; } } And finally, the XAML looks like this: <Window.Resources> <DataTemplate DataType="{x:Type vm:XMoveViewModel}"> <Image Source="XMove.png" Grid.Row="{Binding Path=Row}" Grid.Column="{Binding Path=Column}" Stretch="None" /> </DataTemplate> <DataTemplate DataType="{x:Type vm:OMoveViewModel}"> <Image Source="OMove.png" Grid.Row="{Binding Path=Row}" Grid.Column="{Binding Path=Column}" Stretch="None" /> </DataTemplate> </Window.Resources> <Grid> <ItemsControl ItemsSource="{Binding Path=Moves}"> <ItemsControl.ItemsPanel> <ItemsPanelTemplate> <Grid ShowGridLines="True"> <Grid.RowDefinitions> <RowDefinition /> <RowDefinition /> <RowDefinition /> </Grid.RowDefinitions> <Grid.ColumnDefinitions> <ColumnDefinition /> <ColumnDefinition /> <ColumnDefinition /> </Grid.ColumnDefinitions> </Grid> </ItemsPanelTemplate> </ItemsControl.ItemsPanel> </ItemsControl> </Grid> What was not so obvious to me when I started was that the ItemsControl element actually wraps each item in a container, so my Grid.Row and Grid.Column bindings are ignored since the images are not directly contained within the grid. Thus, all of the images are placed in the default Row and Column (0, 0). What is happening: The desired result: So, my question is this: how can I achieve the dynamic placement of my controls in a grid? I would prefer a XAML/Data Binding/MVVM-friendly solution. Thanks.

  Read the article

• Deploying MVC2 application to IIS7.5 - Ninject asked to provide controllers for content files

  - by Rune Jacobsen

  I have an application that started life as an MVC (1.0) app in Visual Studio 2008 Sp1 with a bunch of Silverlight 3 projects as part of the site. Nothing fancy at all. Using Ninject for dependency injection (first version 2 beta, now the released version 2 with the MVC extensions). With the release of .Net 4.0, VS2010, MVC2 etc., we decided to move the application to the newest platform. The conversion wizard in VS2010 apparently took care of everything, with one exception - it didn't change references to mvc1 to now point to mvc2, so I had to do that manually. Of course, this makes me think about other MVC2 things that could be missing from my app, that would be there if I did File - New Project... But that is not the focus of this question. When I deploy this application to the IIS 7.5 server (running on Win2008 R2 x64), the application as such works. However, images, scripts and other static content doesn't seem to exist. Of course they are there on disk on the server, but they don't show up in the client web browser. I am fairly new to IIS, so the only trick I knew is to try to open the web page in a browser on the server, as that could give me more information. And here, finally, we meet our enemy. If I try to go directly to the URL of one of the images (http://server/Content/someimage.jpg for instance), I get the following error in the browser: The IControllerFactory 'Ninject.Web.Mvc.NinjectControllerFactory' did not return a controller for a controller named 'Content'. Aha. The web server tries to feed this request to MVC, who with its' default routing setup assumes Content to be a controller, and fails. How can I get it to treat Content/ and Scripts/ (among others) as non-controllers and just pass through the static content? This of course works with Cassini on my developer machine, but as soon as I deploy, this problem hits. I am using the last version of Ninject MVC 2 where the IoC tool should pass missing controllers to the base controller factory, but this has apparently not helped. I have also tried to add ignore routes for Content etc., but this apparently has no effect either. I am not even sure I am addressing the problem on the right level. Does anyone know where to look to get this app going? I have full control of the web server so I can more or less do whatever I want to it, as long as it starts working. Thanks!

  Read the article

• Android: Adding static header to the top of a ListActivity

  - by GrandPrix

  Currently I have a class that is extending the ListActivity class. I need to be able to add a few static buttons above the list that are always visible. I've attempted to grab the ListView using getListView() from within the class. Then I used addHeaderView(View) to add a small layout to the top of the screen. Header.xml <?xml version="1.0" encoding="utf-8"?> <LinearLayout xmlns:android="http://schemas.android.com/apk/res/android" android:layout_width="fill_parent" android:layout_height="fill_parent" > <Button android:id="@+id/testButton" android:layout_width="fill_parent" android:layout_height="wrap_content" android:text="Income" android:textSize="15dip" android:layout_weight="1" /> </LinearLayout> Before I set the adapter I do: ListView lv = getListView(); lv.addHeaderView(findViewById(R.layout.header)); This results in nothing happening to the ListView except for it being populated from my database. No buttons appear above it. Another approach I tried as adding padding to the top of the ListView. When I did this it successfully moved down, however, if I added any above it, it pushed the ListView over. No matter what I do it seems as though I cannot put a few buttons above the ListView when I used the ListActivity. Thanks in advance. synic, I tried your suggestion previously. I tried it again just for the sake of sanity, and the button did not display. Below is the layout file for the activity and the code I've implemented in the oncreate(). //My listactivity I am trying to add the header to public class AuditActivity extends ListActivity { Budget budget; @Override public void onCreate(Bundle savedInstanceState) { Cursor test; super.onCreate(savedInstanceState); setContentView(R.layout.audit); ListView lv = getListView(); LayoutInflater infalter = getLayoutInflater(); ViewGroup header = (ViewGroup) infalter.inflate(R.layout.header, lv, false); lv.addHeaderView(header); budget = new Budget(this); /* try { test = budget.getTransactions(); showEvents(test); } finally { } */ // switchTabSpecial(); } Layout.xml for activity: <?xml version="1.0" encoding="utf-8"?> <LinearLayout xmlns:android="http://schemas.android.com/apk/res/android" android:layout_width="fill_parent" android:layout_height="fill_parent"> <ListView android:id="@android:id/list" android:layout_width="wrap_content" android:layout_height="wrap_content" /> <TextView android:id="@android:id/empty" android:layout_width="wrap_content" android:layout_height="wrap_content" android:text="@string/empty" /> </LinearLayout>

  Read the article

• Doing TDD Silverlight 4 RC using Visual Studio 2010 RC

  - by user133992

  First I am glad to see better TDD support in VS2010. Support for generating code stubs from my tests is ok - not as good as more mature TDD plug-ins but a good start. I am looking for some best Silverlight 4.0 TDD practices. First Question: Anyone have links, recommendations? I know the new Silverlight Unit Test capabilities are much better (Jeff Wilcox's Mix Presentation). What I am focusing on right now is using TDD to develop pure Silverlight 4.0 Class Library projects - projects without a Silverlight UI project. I've been able to get it to work but not as cleanly as it should be. I can create an Empty VS project. Add A Silverlight 4 Class Library Project. Add a TestProject (not a silverlight Unit Test Project but a plain Test Project). Add a simple test in the Test Project such as: namespace Calculator.Test { [TestClass] public class CalculatorTests { [TestMethod] public void CalulatorAddTest() { Calc c = new Calc(); int expected = 10; int actual = c.Add(6, 4); Assert.AreEqual<int>(expected, actual); } } } Using the new Generate Type and Method from Test feature it will generate the following code in the Silverlight Project: namespace Calculator { public class Calc { public int Add(int p, int p_2) { throw new NotImplementedException(); } } } When I run the tests the first time it says the target assembly is Silverlight and not able to run test - Not exact text but the same general idea. When I change the implementation to: namespace Calculator { public class Calc { public int Add(int p, int p_2) { return p + p_2; } } } and re-run the test, it works fine and the test goes green. It also works for all other TDD code I generate after. I also get a warning Mark in the Test Project's reference to the Calculator Silverlight Class Library Assembly. Second Question: Any comments ideas if this just a bug in VS2010 RC or is Silverlight Class Library TDD not really supported. I have not created a Silverlight UI project or changed and build or debug settings so I have no idea what is hosting the silverlight DLL. Finally, some of the Silverlight Class Libraries I need to write will provide functionality that requires elevated Out-Of-Browser rights. Based on the above, it looks like I can use TDD Test Projects against regular Silverlight 4.0 Class Libraries, but I have no idea how I can TDD the elevated OOB functionality without also creating the UI component that gets installed. The UI piece is not really needed for the Library development and gets in the way of what I actually want to TDD. I know I can (and will) mock some of that functionality but at some point I will also need the real thing in my tests. Third Question: Any ideas how to TDD Silverlight 4.0 Class Library project that requires OOB elevated rights? Thanks!

  Read the article

• IE7 not digesting JSON: "parse error" [resolved]

  - by Kenny Leu

  While trying to GET a JSON, my callback function is NOT firing. $.ajax({ type:"GET", dataType:'json', url: myLocalURL, data: myData, success: function(returned_data){alert('success');} }); The strangest part of this is that my JSON(s) validates on JSONlint this ONLY fails on IE7...it works in Safari, Chrome, and all versions of Firefox, (EDIT: and even in IE8). If I use 'error', then it reports "parseError"...even though it validates! Is there anything that I'm missing? Does IE7 not process certain characters, data structures (my data doesn't have anything non-alphanumeric, but it DOES have nested JSONs)? I have used tons of other AJAX calls that all work (even in IE7), but with the exception of THIS call. An example data return (EDIT: This is a structurally-complete example, meaning it is only missing a few second-tier fields, but follows this exact hierarchy)here is: {"question":{ "question_id":"19", "question_text":"testing", "other_crap":"none" }, "timestamp":{ "response":"answer", "response_text":"the text here" } } I am completely at a loss. Hopefully someone has some insight into what's going on...thank you! EDIT Here's a copy of the SIMPLEST case of dummy data that I'm using...it still doesn't work in IE7. { "question":{ "question_id":"20", "question_text":"testing :", "adverse_party":"none", "juris":"California", "recipients":"Carl Chan" } } EDIT 2 I am starting to doubt that it is a JSON issue...but I have NO idea what else it could be. Here are some other resources that I've found that could be the cause, but they don't seem to work either: http://firelitdesign.blogspot.com/2009/07/jquerys-getjson.html (Django uses Unicode by default, so I don't think this is causing it) Anybody have any other ideas? ANSWER I finally managed to figure it out...mostly via tedious trial-and-error. I want to thank everyone for their suggestions...as soon as I have 15 rep, I'll upvote you, I promise. :) There was basically no way that you guys could have figured it out, because the issue turned out to be a strange bug between IE7 and Django (my research didn't bring up any similar issues). We were basically using Django template language to generate our JSON...and in the midst of this particular JSON, we were using custom template tags: {% load customfilter %} { "question":{ "question_id":"{{question.id}}", "question_text":"{{question.question_text|customfilterhere}}" } } As soon as I deleted anything related to the customfilter, IE7 was able to parse the JSON perfectly! We still don't have a workaround yet, but at least we now know what's causing it. Has anyone seen any similar issues? Once again, thank you everyone for your contributions.

  Read the article

< Previous Page | 184 185 186 187 188 189 190 191 192 193 194 195  | Next Page >