Search Results

Search found 11077 results on 444 pages for 'ip'.

Page 188/444 | < Previous Page | 184 185 186 187 188 189 190 191 192 193 194 195  | Next Page >

  • Why is this static routing not working ?

    - by geeko
    Greeting gurus, I'm trying to develop a DHCP enforcement extension like Microsoft NAP. My trick to block dynamic-IP requesting machines (that don't meet certain policy) is to strip the default gateway (no default gateway) stated in the IP lease and set the lease subnet mask to 255.255.255.255. Now I need the blocked machines to be able to reach some specific locations (IPs) on the network. To allow for this, I'm including some static routes in the lease. For example, I'm including 10.10.10.11 via router 10.10.10.254 (the one to which the blocked machine that needs to access 10.10.10.11 is connected). Unfortunately, as soon as I set the default gateway to nothing, blocked machines cannot reach any of the added static routes. I also tried classless static routes. Any ideas ? any one knows how MS NAP actually do it ? Geeko

    Read the article

  • Traffic shaping & monthly traffic limit in Tomato?

    - by Matt H
    Is there a way to do a monthly traffic limit in Tomato, DDWRT or OpenWRT in addition to the regular QoS? This is for a house with several students sharing the internet. I.e. for a specific IP address, IP Range or MAC address, the firmware will count the download traffic for that month. When a configurable limit is set, it'll either limit it to say 64kbit/s up/down or drop all traffic and maybe redirect web traffic to an internal web server telling them that they have exceeded their quota. How can this be done with those firmwares?

    Read the article

  • Keepalived takes several minutes to recover in a particular situation

    - by NathanE
    I've setup Keepalived for a master-slave style virtual IP and it seems to work well. Both are hosted in almost identical VMs. If I "pause" the VM that is running the Master. The Slave will take over, as expected, almost instantly. However if I then "unpause" the VM that runs the Master. The virtual IP will stop responding the pings. And it takes a good 4 or 5 minutes for it to start pinging again. It seems to be getting desynchronised due to the nature of the way I'm testing it (by pausing/unpausing the VMs). I admit that pausing and unpausing VMs is a slightly dodgy way to test this. But it has raised a concern for me that there could be other scenarios that cause the same undesirable behaviour. Is this expected / by design? Is there anything I can do to the config to improve it? Thanks.

    Read the article

  • SSH broken, segfault error 4

    - by trampi
    i cannot connect to my server via ssh, it throws me a "server unexpectedly closed connection" after entering the password. in var/log/messages the only noteable message is: Apr 14 17:41:23 s15410270 kernel: sshd[3602]: segfault at c0 ip 7f0801acbdb0 sp 7fff0adff860 error 4 in libc-2.8.so[7f0801a87000+14f000] Apr 14 17:41:29 s15410270 kernel: sshd[3606]: segfault at c0 ip 7f75f9463db0 sp 7fff027971f0 error 4 in libc-2.8.so[7f75f941f000+14f000] This message appears after a log in attempt via ssh or via sftp Its a SuSE Linux server. I'm looking for help where to start to search for the error, i can still act as root via a serial console. edit: "server unexpectedly closed connection" only appears if i enter the correct password!

    Read the article

  • How to make ssh/rsync/etc use a VLAN network interface?

    - by Annan
    A company I work for has a number of virtual servers with ElasticHosts. They are setup in such a way that eth1 is on a private VLAN connecting them to each other. This is so backups sent between servers are not charged at the same rate as external data transfer. My understanding of how VLANs and network interfaces work is sketchy at best. How can I make ssh, rsync, etc. transfer data through the VLAN? My final solution: I spent a while trying to figure this out, For all servers involved, edit /etc/sysconfig/network-scripts/ifcfg-eth1 DEVICE=eth1 BOOTPROTO=static ONBOOT=yes HWADDR=YOUR_MAC_ADDR IPADDR=192.168.0.100 NETMASK=255.255.255.0 Where HWADDR should already be set and the last octate of IPADDR should be different from each other. Then run, on all servers /etc/init.d/network restart After this the IP addresses specified by IPADDR can be used directly as any other IP address.

    Read the article

  • forwardfor information is missing

    - by FAFA
    I use following configuration to load balance https connections, using haproxy 1.4.8. SSL offloading is done by apache. listen ssl_to_waf 192.168.101.54:443 mode tcp balance roundrobin option ssl-hello-chk server wafA 192.168.101.61:444 check listen ssl_from_waf 192.168.101.61:445 balance roundrobin option forwardfor server webA 192.168.101.46:80 check For HTTP requests this works great, requests are distributed to my Apache servers just fine. But for HTTPS request, I lose the "forwardfor" information. I need to save the client IP address. How can I use HAproxy to load balance across a number of SSL servers, allowing those servers to know the client's IP address?

    Read the article

  • Is SYN flooding still a threat?

    - by Rob
    Well recently I've been reading about different Denial of Service methods. One method that kind of stuck out was SYN flooding. I'm a member of some not-so-nice forums, and someone was selling a python script that would DoS a server using SYN packets with a spoofed IP address. However, if you sent a SYN packet to a server, with a spoofed IP address, the target server would return the SYN/ACK packet to the host that was spoofed. In which case, wouldn't the spoofed host return an RST packet, thus negating the 75 second long-wait, and ultimately failing in its attempt to DoS the server?

    Read the article

  • When connected through a router, a new gateway appears, and I lose my internet connection.

    - by idan315
    I have two computers connected to a router, connected to my ADSL modem by PPPoE. One of those computrs use Windows XP, the other uses Windows 7. The computer using Windows 7 keeps getting limited or no connectivity, and I can't use it to connect to the internet. Connecting the computer to the modem without the router 'in the way' worked, and I was able to use the internet - which led me to believe that the problem is with my router. However, I have changed my router, and the problem persists. (Just to be clear: the computer using Windows XP can connect to the internet without any problem). This entire question is about the PC using Windows 7. The only symptom of this problem is that when I see my network devices, in addition to my router (which appears as "Network 4", or something of the sort), I also see an "Unidentified Network". When using ipconfig to check the problem, I see a second gateway, with the IP 0.0.0.0, in addition to the IP of my router.

    Read the article

  • UAE and the mysteries of unreachable websites

    - by 0plus1
    I write here because I'm really lost, please stay with me because it's not easy to explain. A company asked me to set-up a private server, now I'm a programmer so I got a solution with technical support and cpanel which helped me to setup everything and it's working smoothless. I'm by no means a professional sysadmin, but I have a fair knowledge of server configurations, but this problem is way over my knowledge, and apparently way over the knowledge of most sysadmins, I really hope that here I'll find someone with enough experience to help me or at least give me more insight. Now this company for which I'm consulting operates in the UAE (United Arab Emirates) and from there the server is almost unreachable. It started with ns not registering in the UAE, after a week that sorted itself out and now the site is indeed reachable, but it takes almost 2 minutes to load a webpage with one line of text. Emails go in timeout. The domain currently parked there has been bought appositely for tests, the main one that was supposed to go there, after a catastrophic week has been transferred to a shared hosting solution in the UK, and from there it works like a charme. Now after doing some research I discovered that I'm not alone in this, there are several reports of webmasters discovering that their website is not reachable inside the UAE, and mind this has nothing to do with the state-wide block of questionable sites, because in that case an error message appears, this seems to be related to the infrastructure of the UAE, which apparently reroutes everything through their own "fake" internet. Apparently new servers with their own IP are not recognized (yet?) by the UAE infrastructure, while shared hosting solutions seeing that they operates tons of other websites are more likely to be part of the UAE network. Now my questions are: 1) Has someone a real explanation for this? The only thing I can think of is that the server is on a new IP that is not yet recognized by the UAE, but that doesn't explain why it loads (even if after 2 minutes). I don't have any help from within the UAE as the only people that are "experts" are questionable companies that simply try to sell their own services. 2) If there is really some kind of block of new servers, is it possible to know before if a server is reachable from within the UAE, currently this is not a ns problem as even accessing the server with its IP result in a 2 minute wait. 3) Can it be that the problem lies somewhere else? There are some tests that I can perform? I'm not physically in the UAE, but I can ask the people there, or use teamviewer. Could it be some misconfiguration on the server (mind that the site works EVERYWHERE else in the world). Thank you for ANY kind of help

    Read the article

  • What is IPKVM and why would I need that to install SQL Server on my Web Server?

    - by Eric
    Hello. I have a dedicated server, and will be installing SQL Server. However, my hosting company said they can connect an external CD ROM drive and give me KVM over IP to install SQL Server. My question is, what is IPKVM, and how does it work? Do I need special hardware or software on my side to use it....or do I just connect via remote desktop? Also, why can't I remote into my server through remote desktop instead of using KVM over IP?

    Read the article

  • How to do complex port forwarding (sort of)

    - by adnan kamili
    I have a very different situation. My laptop named A, another machine B(ip-172.16.28.3) with ssh server installed and i have an account on that machine, the third machine C(ip-172.16.24.3) is a proxy server. All the machines are within a LAN, but 1- Machine B can connect to A as well as C 2- Machine A i.e.my pc, it can only connect to B and not C Now to use internet, i do the following: ssh -X [email protected] Then i type firefox and i use the firefox of machine B with proxy setings as 172.16.24.3:3128 Instead of using firefox of B, i want to use my local firefox. Is there a way through which i can connect to C via B and use my local firefox for browsing

    Read the article

  • Iptables based router inside KVM virtual machine

    - by Anton
    I have KVM virtual machine (CentOS 6.2 x64), it has 2 NIC: eth0 - real external IP 1.2.3.4 (simplified example instead of real one) eth1 - local internal IP 172.16.0.1 Now I'm trying to make port mapping 1.2.3.4:80 = 172.16.0.2:80 Current iptables rules: # Generated by iptables-save v1.4.7 on Fri Jun 29 17:53:36 2012 *nat :OUTPUT ACCEPT [0:0] :PREROUTING ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] -A POSTROUTING -o eth0 -j MASQUERADE -A PREROUTING -p tcp -m tcp -d 1.2.3.4 --dport 80 -j DNAT --to-destination 172.16.0.2:80 COMMIT # Completed on Fri Jun 29 17:53:36 2012 # Generated by iptables-save v1.4.7 on Fri Jun 29 17:53:36 2012 *mangle :PREROUTING ACCEPT [0:0] :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] COMMIT # Completed on Fri Jun 29 17:53:36 2012 # Generated by iptables-save v1.4.7 on Fri Jun 29 17:53:36 2012 *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] COMMIT # Completed on Fri Jun 29 17:53:36 2012 But there is nothing works, I mean it does not forwards that port. Similar configuration without virtualization seems to be working. What am I missing? Thanks!

    Read the article

  • How is the MTU is 65535 in UDP but ethernet does not allow frame size more than 1500 bytes

    - by nikku
    I am using a fast ethernet of 100 Mbps, whose frame size is less than 1500 bytes (1472 bytes for payload as per my textbook). In that, I was able to send and receive a UDP packet of message size 65507 bytes, which means the packet size was 65507 + 20 (IP Header) + 8 (UDP Header) = 65535. If the frame's payload size itself is maximum of 1472 bytes (as per my textbook), how can the packet size of IP be greater than that which here is 65535? I used sender code as char buffer[100000]; for (int i = 1; i < 100000; i++) { int len = send (socket_id, buffer, i); printf("%d\n", len); } Receiver code as while (len = recv (socket_id, buffer, 100000)) { printf("%d\n". len); } I observed that send returns -1 on i > 65507 and recv prints or receives a packet of maximum of length 65507.

    Read the article

  • How do http proxies determine https traffic with a single port?

    - by badunk
    If a proxy receives the tcp packet, then the destination ip address and port are that of the proxy. In that case, I imagine the only way a proxy can still resolve the intended destination is either through routing the source ip address/port or through the host field in the http header. Is this correct? In both Fiddler and Charles http proxies, I noticed that the tool accepts both http and https connections through a single port that you can specify. What do these tools do to tell the difference between the two types of connections?

    Read the article

  • Can't ping self

    - by Paddy
    I have a wireless internet connection setup on my Mac. (v10.5.6) Am connected to the internet and everything is running smoothly. I recently discovered a quirky behaviour while setting up apache web server. When i typed in my dynamic ip (http://117.254.149.11/) in the webbrowser to visit my site pages it just timed out. In terminal i tried pinging localhost and it worked. $ ping localhost PING localhost (127.0.0.1): 56 data bytes 64 bytes from 127.0.0.1: icmp_seq=0 ttl=64 time=0.063 ms 64 bytes from 127.0.0.1: icmp_seq=1 ttl=64 time=0.056 ms 64 bytes from 127.0.0.1: icmp_seq=2 ttl=64 time=0.044 ms But if i pinged my ip it would just time out. $ ping 117.254.149.11 PING 117.254.149.11 (117.254.149.11): 56 data bytes ^C --- 117.254.149.11 ping statistics --- 10 packets transmitted, 0 packets received, 100% packet loss Pinging any other site works though. I am completely stumped. Any help would be greatly appreciated.

    Read the article

  • faking NAT with a VMware distributed switch across multiple hosts

    - by romant
    I need to construct a NAT for certain machines within the network. Wish to do this with dvSwitch - as it seems the logical way of attacking the problem as in this scenario there's just under 30 hosts. In order for the NAT'ed VM's to have access to the 'real' network. I am providing a 'router' VM, which will have access to the WAN/outside network, and also act as the DHCP server for the NAT'ed machines. Problem Space When the machines connected to the NAT interface and the router are on the same host, then they get an IP from the router VM, and work perfectly (routed outside). Unfortunately machines on other Hosts that are connected to the dvSwitch do not get an IP and further tcpdump shows no network data getting through across the hosts within the dvSwitch. Has anyone achieved a NAT solution using a dvSwitch before that they could share?! Thank you. EDIT: Including the diagram.

    Read the article

  • Cannot connect to network

    - by dany
    I have a problem: I am on Debian. I configured my nic with a static ip (192.168.1.56). When I try to connect to a network, initially with ifconfig eth2 I get (correctly): eth2 inet addr:192.168.1.56 .... inet6 addr: fe80:221:ff:fe96:4598/64 but after a few seconds the 192.168.1.56 disappears and after some other seconds disappears the inet6 address too. When I press in the nm-applet it requires me the password but in the meantime it try to connect. At uni, the connection is a DHCP one. It works for the first few seconds but after it doesn't. Any possible solution? Here it is the relevant part of the syslog: (static ip configuration) http://pastebin.com/u3BPAsda

    Read the article

  • How come I can't ping my home computer?

    - by bikefixxer
    I'm trying to set up a vpn into my home computer in order to access files from wherever. I have the home computer set up with a no-ip dynamic dns program so I can always connect, and have also tried using the actual ip address. However, when I try to connect or even ping from anywhere outside of my house I can't get through. I've tried putting that particular computer in the dmz, turned off the computers firewall and anti-virus, and I still don't get anything. I have comcast as my home internet provider. I have also tried from two different locations. Are there any other solutions I can try or is comcast the issue? I used to be able to do this when I ran a small web server at home for fun but now nothing works. Thanks in advance for any suggestions!

    Read the article

  • Iptables mark incoming packet - vpn routing

    - by Tom
    I have connected my home to my workplace for out of house backup reasons through openvpn. The connection is working nicely. At work I have 5 fixed IP addresses. Now I would like to assign one of these IP addresses to be forwarded to my home machine. I have confirmed packet arrival at my home machine with tcpdump. The problem is that my default route at home is NOT the tun0 (naturally), but eth0 to my own ISP. So I created a separate routing table to route my tun0 packets back to where they belong, but do not how to mark the incoming packet which arrive through tun0 with iptables, so I can drive them back. I do not want any port restrictions, but only what comes from tun0 should leave through tun0 thanks tom

    Read the article

  • How can I have 2 users working on the same PC at the same time

    - by Sharon Cook
    I have a pc/machine that has its own ip address and it can be connected to by certain external PC's through our firewall. User A has a RDP connection from say Germany directly to the PC - his ip number is allowed through our firewall to connect to the PC. He now wants User B to connect at the same time so that User B can see what User A is doing on the screen at the same time and maybe take over the screen to put his input in. I know that you cannot have 2 RDP connections at the same time but what would be the easiest solution to this. I want User A to keep his RDP connection, but I am unsure of what to suggest so that User B can see what is going on at the same time. The Users are not happy to use Real VNC, etc.

    Read the article

  • Remote location looses connectivity

    - by user24559
    I have a remote location that has constant internet access using DSL. The remote location only has three Linksys cameras that use the internet access with a router. There is no computer on the network. The router is configured to use the DYN.org service to keep the IP address updated if the internet provider assigns a new ip address. The problem I am having is the router after a period of time stops responding to incoming ping requests and the cameras are shown offline. However, if I keep one of the cameras constantly streaming data then the connection to all the cameras works just fine all the time. How can I keep the router from appearing to be sleeping and not responding to incoming requests? The router is the Linksys WRT300N.

    Read the article

  • How to test DNS glue record?

    - by Sunnz
    Hello I have just set up a DNS server for my domain example.org with 2 name servers ns1.example.org and ns2.example.org. I have attempted to set up a glue record for ns1 and ns2 at my registrar. It seems to work for now when I do a dig example.org but when I do a whois example.org it lists ns1.example.org and ns2.example.org but not their IP address which should be set up as a glue record. So I am wondering how do I check for the existence of a glue record? Do I do it with whois? I have seen .com and .net whois records that have both the domain name as well as the IP address for the name servers, is .org different? What's the proper way to test this? Thanks.

    Read the article

  • Hyper-V management remotely

    - by Péter
    I'll tell you in advance that I'm newbie in the topic. I have a Win8 (Home) machine with Hyper-V installed behind a router. The router has a public IP and a domain attached. I have another Win8 (Work) machine also installed Hyper-V. I want to access to my home Hyper-V via Hyper-V Manager so I can manage my virtual machines from work. I found this article but I don't know if it's applicable to me. I thought that a simple port forwarding should work and I only need to do is grant the Work HV manager my domain and the port I choose and if it's pop a login form I only need to fill the user data of my Home computer? How can I solve this? My thoughts revolve around: - Port forwarding - set domain+port and set my home user - Set up a VPN and use the local ip address of my home computer (it looks like a little cumbersome and my router only support PPTP) I'm open to any other solution too. Thanks, Péter

    Read the article

  • Configuring subdomains for a machine (Win2k8) in a lan

    - by RMS
    I am currently setting up a windows 2008 server to host a website with multiple subdomains, all accessible only within the lan. also, there is no active directory. what I did is : 1 - computer name : 'web' 2 - in IIS, I added a site binding as 'site1.web' to the default web site 3 - added DNS role to the server 4 - added 'web' as principal zone in direct lookup zones (default options) 5 - added CNAME 'site1' From a client machine, in tcpip config I added the ip address of 'web' to the DNS list in addition to the ISP DNS. (client machine ip is from DHCP) Now browsing to 'http://web' or 'http://site1.web' works correctly. My question is, is it possible throught additional steps in the server to have the websites accessible without requiring the DNS config in all the client machines ? thanks in advance

    Read the article

  • Configuring Linux Network

    - by Reiler
    Hi I'm working on some software, that runs on a Centos 5.xx installation. I'ts not allowed for our customers to log in to Linux, everything is done from Windows applications, developed by us. So we have build a frontend for the user to configure network setup: Static/DHCP, ip-address, gateway, DNS, Hostname. Right now I let the user enter the information in the Windows app, and then write it on the Linux server like this: Write to /etc/resolv.conf: Nameserver Write to /etc/sysconfig/network: Gateway and Hostname Write to /etc/sysconfig/network-scripts/ifcfg-eth0: Ipaddress, Netmask, Bootproto(DHCP or Static) I also (after some time) found out that I was unable to send mail, unless I wrote in /etc/hosts: 127.0.0.1 Hostname All this seems to work, but is there a better/easier way to do this? Also, I read the network configuration nearly the same way, but if I use DHCP, I miss som information, for instance the Ip-address. I know that I can get some information from the commandline (ifconfig), but I dont get for instance Hostname, Gateway and DNS. Is there a commandline tool that will display this?

    Read the article

< Previous Page | 184 185 186 187 188 189 190 191 192 193 194 195  | Next Page >