Search Results

Search found 7843 results on 314 pages for 'power over ethernet'.

Page 188/314 | < Previous Page | 184 185 186 187 188 189 190 191 192 193 194 195  | Next Page >

• Using VMware's ESXi, can I plug in 30 USB Wireless adapters and allow each of 30 VMs one?

  - by 31eee384

  I'm assuming ESXi will act very similarly to VMware Workstation or other products, so answers based on knowledge of those programs might also help. I want to plug in 30 USB Wireless or Ethernet adapters into my server, and let each VM access one and only one of these devices. Unfortunately, I don't have the hardware to just try it out as the purchase of hubs and adapters hinges on the result of this question. The answer could be a resounding "yes, easy!" and that would be great. I couldn't find any answers to this question with google, and it's possible that this is because it's so easy to do. Thanks!

  Read the article

• Cannot install wireless lan service on windows 2012 RTM offline

  - by user1763118

  I'm having trouble installing the wireless lan service offline with a fresh installed windows 2012 server RTM. I tried "install-windowsfeature wireless-networking" in the non-gui mode and using the server manager in the gui mode to enable the wireless lan service, but both of them show a "failure configuring windows updates" message after the installation restarted the system. I checked the event log and I think messages about "The WLAN Autoconfig service depends on the following service: nativewifip. This service might not be installed" are the source of the issue. Google shows it is a service called "native wifi filter", but I cannot find anywhere to install that service. I don't have a Ethernet adapter for that computer, so have to install everything offline before the wifi's working.

  Read the article

• Linking two networks that have a common device

  - by Serban Razvan

  I recently bought a Samsung Smart TV having in mind to connect it to the Internet. Because my router is very far from it and not wanting to buy an expensive wireless for the TV, I created a homemade solution. I have the laptop (an smartphone and the PC) connected to the router which is connected to the internet. I shared the laptop's wireless connection to the ethernet port which I connected to the TV. So far, the TV is connected to the internet, but is there any way to make him part of the router's network instead of the 2 devices network (the laptop and the TV)?

  Read the article

• Esxi with iSCSI SAN slows down with many multiple VMs running

  - by varesa

  I have a server with ESXi 5 and iSCSI attached network storage(4x1Tb Raid-Z on freenas). Those two machines are connected to each other with Gigabit ethernet, and a procurve switch in between. After a while, if I have many(4-5 or more) vms running, they start to get un-responsive (long delays before anything happens). We are trying to find the reason behind this. Today we looked at esxtop, and found that DAVG of that iSCSI LUN stays at 70-80. I read that +30 is critical! What could be causing those high response-times?

  Read the article

• Can't access internet even though everything is working

  - by entity64

  A friend recently upgraded to a new cable internet connection. The modem connects to the router and various PCs and smartphones from her roommates connect to the router. They don't have any problem accessing the internet. She has Windows 8 and can't access any website (via wifi and ethernet). DNS (UDP) is working, DHCP set up everything correctly, Wifi is working, Trace routes and Pings (ICMP) go through with no problem at all. But neither Dropbox nor Skype nor Spotify nor any browser (all TCP) can access any website. The thing is though, she can connect through the university wifi and via a neighbors wifi. It's just her home connection. No firewalls are running and the computer is clean - no malware. How could it be that only her home connection won't work and others do?

  Read the article

• PCs with Wired Connection Keep Losing Internet Connectivity

  - by user717452

  I have a U-verse ATT DSL Internet at our church building. Recently, any computer that is plugged into the network via Ethernet keeps losing its internet connectivity. The setup is from the Modem to a Netgear Wireless Router, and from the router to 3 different computers. None of the laptops that use Wifi ever lose internet, just the wired ones, and I end up having to do ipconfig /release and /renew every day to get it back. One computer has Windows 7 and one has Windows XP. Any ideas as to what is going on with our network?

  Read the article

• Is there a Linux kernel boot parameter to configure an IPv6 address?

  - by aef

  I know there is a parameter named ip which lets you configure IPv4 addresses on the Linux kernel through the boot loader. That looks like the following: ip=192.0.2.1::192.0.2.62:255.255.255.192::eth0:none I'm looking for an equal parameter for IPv6 configuration. I couldn't find anything about this in the kernel documentations. Update: Because of a lot of you asked why I would need this: The idea to use a kernel configuration came up related to this problem. I suspect the regular boot-up interface configuration is not done, because the interfaces are already up. The reason for this could be that I'm using a pre-boot environment with a Dropbear SSH server to allow me to unlock my encrypted root partition. The IP addresses for this environment are configured through GRUB with the ip= parameter. There is no DHCP or Router Advertisement available on that Ethernet segment and as this is the uplink segment provided by a large hosting company, there is no way to change that fact.

  Read the article

• What is the "real" difference between a NAS and NFS?

  - by warren

  From an end-user perspective, what is the difference between a NAS device and using NFS exports from a file server? They seem to accomplish the same end result. The difference between a SAN and other file storage is related (in my experience) to how they are connected to the server infrastructure. However, the difference between a NAS, connecting over standard ethernet, and NFS (sharing storage off specific servers, also over the network), seems more nebulous. Is there a good reason to pick a NAS filer over NFS on servers?

  Read the article

• Can the onborad LAN cause computer shutdown

  - by user1146320

  I have P4 processor with nvidia card. Now if i don't connect to internet then my computer stays on for as much i can like 4-5 days. But if i plug in the ethernet wire. Do some surfing and leave computer as it is. Then computer fails. I mean The display on screen gets off Looks like something stopping the power supply to Harddisk. But motherboard stays on , FAN is still running , i can eject CD drive as well. But no display on monitor. I have to turn off and then turn on again. I tried formatting windows XP but again same problem

  Read the article

• Unable to change IP address for eth0 without restart in Ubuntu

  - by Rodnower

  I have Ubuntu 12.04.1 installed. I tried to change the IP address of the interface eth0 in /etc/network/interfaces from 192.168.1.3 to 192.168.1.4 auto lo iface lo inet loopback pre-up iptables-restore < /etc/iptables.up.rules auto eth0 iface eth0 inet static address 192.168.1.4 gateway 192.168.1.1 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 sudo service networking status When I issue: sudo service networking restart I get this response: stop: Unknown instance: networking stop/waiting And IP remains 192.168.1.3: eth0 Link encap:Ethernet HWaddr 00:1e:33:71:cd:a4 inet addr:192.168.1.3 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21e:33ff:fe71:cda4/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3861 errors:0 dropped:0 overruns:0 frame:0 TX packets:3291 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3423285 (3.4 MB) TX bytes:521854 (521.8 KB) Interrupt:45 Base address:0x4000 Only after restart does the IP change. Any ideas?

  Read the article

• Why are the external IP of my router not the same as the external IP of my computer

  - by Martin

  I have a standard network setup where all my network devices, both WIFI and ethernet, are connected to the same router. Lately, however, I've been experiencing some very strange behavior. It started as a simple connecting error, when I tried to reach an FTP server using the external IP. Of course I went right into one of those CheckMyIP sites, to double check the IP and it turned out to be correct. Then I went into my router setup, which is through a tool called aiport-tool, because I have an Apple Aiport Extreme router. Turns out the router displays a different external IP, and for some reason that external IP works when I try to access the FTP server. Can anyone explain what is going on? Why are the devices connected to the router displaying an incorrect external IP? BTW i have no VPN/proxy setups on any of my devices.

  Read the article

• Frequent connection drops when playing online games (StarCraft 2, Battlefield 3) and behind NAT - how to diagnose?

  - by Moshev

  I am having some trouble with (I suspect) my wireless router. It's connected to the internet with a regular lan cable and has a static, public IP address. Our two home PCs connect to the router with regular lan cables, plus there's a laptop which connects over wifi. diagram: Internet | | <- isp-supplied cat5 ethernet cable | D-Link D300 ...wifi... laptop / \ / <- cable -> \ PC1 PC2 The PCs and laptop are behind NAT and share the router's public IP. The router is a D-Link D300. PC1 is used for online gaming and I'm experiencing frequent "connection dropped" errors when playing Battlefield 3, StarCraft 2 and the Diablo 3 beta; but not with TeamFortress 2 or the Tribes Ascend beta. The issue goes away when I remove the router and connect PC1 directly to the ISP's cable. I have also tried disconnecting PC2 and the laptop, leaving PC1 as the only machine connected to the router - doesn't help. How can I diagnose what precisely the issue is?

  Read the article

• "SIOCSIFADDR: No such device" after restoring backup

  - by Paul Tomblin

  I bought some new hardware, and tried to restore my backup on it. When I boot, I don't get a network connection. If I type "ifup eth0" on the command line, I see the messages: SIOCSIFADDR: No such device eth0: No such device lspci shows an ethernet controller (Intel 82546GB). ifconfig does not show any controller except loopback. I tried installing bare Debian on the machine and the network worked then, but now I want to make it like my old machine was. Googling this problem only seems to find people having this problem in VMs. I'm not in a VM.

  Read the article

• routing problems

  - by user174050

  I have an windows 7 laptop and I have installed openvpn 2.2x as client. The laptop has 2 ethernet cards, one of them is wireless. The wireless lan is 192.168.1.0/24 The Fix lan is 192.168.2.0/24 If I connect to the openvpn server useing the Fix lan the I can connect properly and for testing I ping to my openvpn server 10.0.0.1 that answers correctly. But if I connect to the openvpn server useing the wireless lan, I can establish the connection but pinging to the server isn´t possible. The packets goes allways lost. Why can this happen? In an other laptop where windows xp is installed and with the same lan configuratio everything works propperly. In both cases the firewall is configured to access the vnc server and the server directories useing samba. With the XP I have no problems. I will thank you for all help Ignacio

  Read the article

• Extend university wifi network

  - by asfasdoiuh ouhouhouh

  i live in a university campus and i can get wifi signal on the outside of my window but not in the house. The solution i use at the moment is a usb wifi dongle outside connected to my laptop but the lack of an internal antenna make the connection quite unreliable at times. So i was trying to find another solution to improve the reception of my network. One idea is to setup a router on the outside (in a place with stronger signal) and redirect the connection inside the house with an ethernet cable but the problem is that our Uni Wifi is managed by a capitve portal (BlueSocket with DNS redirection to login page) and the authentication has to happen on the mac address that connect to the net (so the client appliance in this case). If I use a router with Mac-Clone capability i will be able to be redirected trough the captive portal on my laptop computer and login from there or i need to setup my router to fill in the login page by itself? There are other hardware/software solutions i can use to get what i want?

  Read the article

• D Link DSL G624T Router will work wirelessly but not via cable

  - by Andy Fensome

  I have a D Link router which works in providing a wireless internet connection for my main PC and secondary notebook. I have been advised that the internet connection to the main pc will be better if I wire the router directly to the PC. I have tried this and can not get a connection. I just keep getting the message network cable unplugged. I have had the ethernet adaptor checked out on the pc and the cable is good ( also checked out). Anything I can do or do I have a bad router. I have tried the cable in all 4 ports and the message is still the same.

  Read the article

• Using VMware's ESXi, can I plug in 30 USB Wireless adapters and allow each of 30 VMs one?

  - by 31eee384

  I'm assuming ESXi will act very similarly to VMware Workstation or other products, so answers based on knowledge of those programs might also help. I want to plug in 30 USB Wireless or Ethernet adapters into my server, and let each VM access one and only one of these devices. Unfortunately, I don't have the hardware to just try it out as the purchase of hubs and adapters hinges on the result of this question. The answer could be a resounding "yes, easy!" and that would be great. I couldn't find any answers to this question with google, and it's possible that this is because it's so easy to do.

  Read the article

• Is there any chance that my data will get silently corrupted with a robocopy SMB network transfer?

  - by Archagon

  I'm setting up a NAS box for the first time. At the moment, I have most of my data backed up to a few local hard drives, and I intend to transfer all the data to my NAS over ethernet once the RAID array is setup. Since this is all happening over the network, I'm a bit worried about my data getting corrupted silently during transfer. From what I understand, data generally doesn't get corrupted without notice on local transfers because a checksum is performed at some point by the drive or the OS. (This could be totally wrong.) Does the same thing happen with SMB, or is it up to the transferrer to check the integrity of their data? And if it doesn't happen with SMB, is there a protocol that does ensure data integrity? I know that rsync can checksum a transfer, but I'm on Windows and I already have a robocopy configuration that I like. Will my data be safe or do I have to use an external checksum tool to make sure?

  Read the article

• Network not detected, but internet working

  - by Dave

  I am using a brand new HP computer with Windows 7 64 bit. When I first hooked it up it detected my network (hooked up through ethernet) easily. However, after I uninstalled Norton Internet Security, it stopped being able to detect my home network. I can still use the internet as if connected, but I can't go into the network options to communicate with other computers. I had this same problem on Windows Vista on my previous computer. Is there any way to fix this so it detects the network?

  Read the article

• Citrix Xen VM's lose networking

  - by Ash

  My client has a XenServer 6.0.2 installation with 2 Window Server 2008 R2 virtual machines. Whenever the virtual machines are rebooted they lose their IP settings (IP address, subnet, gateway). Each time after a reboot I need to login to each VM via XenCenter and re-apply the required static IP settings. This causes issues with connected iSCSI drives within each VM - drives need to be reconnected after each reboot. For example, a network adapter has the following settings pre-reboot: Description . . . . . . . . . . . : Citrix PV Ethernet Adapter #0 Physical Address. . . . . . . . . : C6-FB-A2-4F-2C-F3 IPv4 Address. . . . . . . . . . . : 10.101.0.101(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 10.101.0.10 DNS Servers . . . . . . . . . . . : 10.101.0.100 NetBIOS over Tcpip. . . . . . . . : Enabled Post-reboot: Description . . . . . . . . . . . : Citrix PV Ethernet Adapter #0 Physical Address. . . . . . . . . : C6-FB-A2-4F-2C-F3 Autoconfiguration IPv4 Address. . : 169.254.153.174(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.0.0 Default Gateway . . . . . . . . . : DNS Servers . . . . . . . . . . . : 10.101.0.100 NetBIOS over Tcpip. . . . . . . . : Enabled Under XenCenter -- Virtual Network Interfaces, each adapter is set to a static MAC address (i.e. "Use this MAC address"). I have tried the following commands within one VM but this had no effect: netsh winsock reset catalog netsh int ip reset Can someone please help?

  Read the article

• VMware Workstation 7&8&9 does not generate /etc/vmware/network upon installation

  - by dash17291

  When I install VMware Workstation on Arch linux Virtual ethernet is not working. $ sudo tail /var/log/vnetlib Aug 28 22:20:33 VNLFileExists - Cannot check for file or directory: /etc/vmware/networking , error: No such file or directory Aug 28 22:20:33 VNLNetCfgLoad - Import file does not exist Aug 28 22:20:33 VNL_Load - Error loading the vnet configuration, file used: /etc/vmware/networking Aug 28 22:20:33 VNLNetCfgUnload - Requested cache is not loaded Database file is not present. Failed to initialize Aug 28 22:20:41 VNLFileExists - Cannot check for file or directory: /etc/vmware/networking , error: No such file or directory Aug 28 22:20:41 VNLNetCfgLoad - Import file does not exist Aug 28 22:20:41 VNL_Load - Error loading the vnet configuration, file used: /etc/vmware/networking Aug 28 22:20:41 VNLNetCfgUnload - Requested cache is not loaded Required modules compiled. Previously I have copied that file or directory (I don't remember) from a working installation, but now I need a real solution. It's strange for me, may be a hardware issue also because with Ubuntu the same thing happens on the same computer.

  Read the article

• Use LAN to interface Synergy while having WiFi connected to internet

  - by freonix

  Similar question and solution I have LAN and WiFi connection, with the WiFi connected to internet and the LAN is simply connected via an Ethernet cable between two computers. I need to get Synergy working without compromising the WiFi internet. I've tried the solution above but couldn't seem to work. Both of the computer are running Windows XP. Even setting the LAN IP to static and under the same subnet doesn't seem to work. Anyone with similar situation and got Synergy to work? edit : Refined the question for clarity. Also, the computer are able to ping each other. Remote desktop can be accessed as well. I suspect the problem lies in Synergy's configuration.

  Read the article

• Can I use my Belkin router as a repeater?

  - by Kyle R

  I've got a brand new, unopened Belkin N600 DB router (yay 50% off sale), and I can't seem to figure out if I can use it as a repeater. As far as I can tell, it doesn't support DD-WRT or Tomato, but I'm wondering if there may be some way to rig it up to repeat Wifi. Also, I really need to know before I open it, because, being a bit tight on money at the moment, I'll probably sell it if I can't use it as a repeater. Finally, two caveats: I can't use the other wireless router for anything other than broadcasting straight from the modem (parents are paranoid about anything technological). I can't run ethernet to the second router due to the layout of the house. Thanks so much for the help everyone--if I'm being vague, tell me! EDIT: Also, the manual here is pretty useless on this topic as far as I can tell.

  Read the article

• What is the "real" difference between a NAS and NFS? Or, why pick a NAS device over "mere" NFS?

  - by warren

  From an end-user perspective, what is the difference between a NAS device and using NFS exports from a file server? They seem to accomplish the same end result. The difference between a SAN and other file storage is related (in my experience) to how they are connected to the server infrastructure. However, the difference between a NAS, connecting over a standard ethernet port, and NFS (sharing storage off specific servers, also over the network), seems more nebulous. Is there a good reason to pick a NAS filer over just running NFS on servers?

  Read the article

• Unable chage IP address for eth0 without restart in Ubunto

  - by Rodnower

  I have Ubuntu 12.04.1 installed. I try to change IP address of the interface eth0 in /etc/network/interfaces from 192.168.1.3 to 192.168.1.4: auto lo iface lo inet loopback pre-up iptables-restore < /etc/iptables.up.rules auto eth0 iface eth0 inet static address 192.168.1.4 gateway 192.168.1.1 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 sudo service networking status Now I issue: sudo service networking restart I have response: stop: Unknown instance: networking stop/waiting And IP remains 192.168.1.3: eth0 Link encap:Ethernet HWaddr 00:1e:33:71:cd:a4 inet addr:192.168.1.3 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21e:33ff:fe71:cda4/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3861 errors:0 dropped:0 overruns:0 frame:0 TX packets:3291 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3423285 (3.4 MB) TX bytes:521854 (521.8 KB) Interrupt:45 Base address:0x4000 Only after restart IP changing... Any ideas?

  Read the article

< Previous Page | 184 185 186 187 188 189 190 191 192 193 194 195  | Next Page >