Search Results

Search found 12899 results on 516 pages for 'jrockit virtual edition'.

Page 189/516 | < Previous Page | 185 186 187 188 189 190 191 192 193 194 195 196  | Next Page >

• Windows 2000 Inaccessible Boot Device

  - by Foo_Chow

  I am working with a machine that had its motherboard die. The machine is running Windows 2000 for legacy software. After the motherboard died I used disk2vhd to perform a physical to virtual transfer. The drive data seemed to copy over to the vhd file well. However, whenever i try to boot I get a message saying Inaccessible Boot Device So far I have tried several things to fix it. fixMBR fixBoot chkdsk windows 2000 automated repair Also, I have attempted to open the registry of the vhd without any success. There is another fix that i have seen suggested that requires editing the registry. Is it possible to open a Windows 2000 hive in another OS or another copy of Windows 2000? One other thing to note is that the error appears in all of Virtual PC 2007, Hyper-V and VMWare Player. Does anyone know how to get past this?

  Read the article

• VirtualBox networking problem, host XP, guest Debian

  - by Silma

  Hi, I'm trying to set up a development environment in a virtual machine on my laptop, with debian os. I have both lan and wlan available on the host machine, yet I can't connect to the internet using either. As I said the host OS is windows XP and the guest OS will be the latest Debian, we downloaded the business card net install so we need internet access from the beginning, besides we need the virtual machine to be visible on the local network (for my fellow developers). We tried host-only networking, NAT, bridging, with proxy (the local network uses a proxy to connect to the internet) and without proxy, nothing seems to work. What else can we do? Thanks a lot.

  Read the article

• Can you use a USB dongle inside a VMWare ESX Virual Machine?

  - by Keith Sirmons

  Howdy, I need to know if a USB dongle that is required as a license key for a piece of software will accessible from the physical host machine. This will be a small vSphere 4 installation targeting the quick backup and system restore capabilities of VMWare, not specifically HA, so I am not to worried about the virtual machine automatically failing over to another physical machine and the dongle not being accessible. Does ESX have the capability to map a physical USB port or device to a specific Virtual Machine? I believe this is the dongle: Sentinal Superpro USB Dongle by Rainbow Technologies Thank you, Keith

  Read the article

• 'inode table usage' spiking every morning at 8am

  - by Harry Wood

  I installed munin on my ubuntu server. It's showing my 'inode table usage' spiking every morning at 8am. It then rapidly curves down and settles over the course of several hours. What might cause this? I thought it might be something running in /etc/cron.daily but this was set to run at 6a.m. and I've changed it to 4am. The spike remains at 8am. I also enabled cron logging, but can't see anything getting launched at 8a.m. It's a virtual server hosted by memset. Could it be caused by something happening on the virtual host?

  Read the article

• Why does httpd handle requests for wrong hostnames in SSL mode?

  - by Manuel

  I have an SSL-enabled virtual host for my sites at example.com:10443 Listen 10443 <VirtualHost _default_:10443> ServerName example.com:10443 ServerAdmin [email protected] ErrorLog "/var/log/httpd/error_log" TransferLog "/var/log/httpd/access_log" SSLEngine on SSLProtocol all -SSLv2 SSLCipherSuite HIGH:MEDIUM:!aNULL:!MD5 SSLCertificateFile "/etc/ssl/private/example.com.crt" SSLCertificateKeyFile "/etc/ssl/private/example.com.key" SSLCertificateChainFile "/etc/ssl/private/sub.class1.server.ca.pem" SSLCACertificateFile "/etc/ssl/private/StartCom.pem" </VirtualHost> Browsing to https://example.com:10443/ works as expected. However, also browsing to https://subdomain.example.com:10443/ (with DNS set) shows me the same pages (after SSL certificate warning). I would have expected the directive ServerName example.com:10443 to reject all connection attempts to other server names. How can I tell the virtual host not to serve requests for URLs other than the top-level one?

  Read the article

• activesync not working with forms based authentication

  - by Chad

  I have an Exchange 2003 SP2 single backend server with an SSL cert. I was having trouble getting OMA to work so I found a MS article about making a reg hack and creating a new Exchange-OMA virtual directory. I am able to connect and access content from my mailbox by using secure mail.domainname.com/oma and using my credentials. ActiveSync was not working on a Windows mobile phone or iPhone. I found another article about using Forms Based Authenication and SSL on a single Exchange server environment and the fix was to elliminate FBA and SSL for the Exchange virtual directory. That allows ActiveSync to now work. I have very few mobile users, but they are management, so I need to make ActiveSync work but I would like to get back to using SSL. http://support.microsoft.com/kb/817379 Any ideas about this setup? Thanks.

  Read the article

• Can't connect disk management to remote XP PC from local Win7/Server 2008

  - by Grez

  Scenario as follows: support technicians using Windows 7 PC's or Server 2008 terminal server are unable to connect Disk Management MMC snap in to a remote PC when the remote device is running Windows XP. "Disk management could not start Virtual Disk Service (VDS) on ". This can happen if the remote computer does not support VDS, or if a connection cannot be established because it was blocked by Windows Firewall." Connecting from another XP machine or 2003 server to the same XP machines works fine. Even connecting from XP/2003 to the Win7 or 2008 server works fine. Windows firewall disabled on all devices. I'm guessing this is something to do with the fact that XP uses logical disk manager service whereas Win7/2008 use Virtual disk manager service. But there doesn't seem to be any way to use logical disk manager service from 7/2008 to connect to XP...

  Read the article

• IPvsadm not equally balancing on wlc scheduler

  - by davidsmalley

  For some reason, ipvsadm does not seem to be equally balancing the connections between my real servers when using the wlc or lc schedulers. One real server gets absolutely hammered with requests while the others receive relatively few connections. My ldirectord.cf file looks like this: quiescent = yes autoreload = yes checktimeout = 10 checkinterval = 10 # *.site.com http virtual = 111.111.111.111:http real = 10.10.10.1:http ipip 10 real = 10.10.10.2:http ipip 10 real = 10.10.10.3:http ipip 10 real = 10.10.10.4:http ipip 10 real = 10.10.10.5:http ipip 10 scheduler = lc protocol = tcp service = http checktype = negotiate request = "/lb" receive = "Up and running" virtualhost = "site.com" fallback = 127.0.0.1:http The weird thing that I think may be causing the problem (but I'm really not sure) is that ipvsadm doesn't seem to be tracking active connections properly, they all appear as inactive connections IP Virtual Server version 1.2.1 (size=4096) Prot LocalAddress:Port Scheduler Flags -> RemoteAddress:Port Forward Weight ActiveConn InActConn TCP 111.111.111.111:http lc -> 10.10.10.1:http Tunnel 10 0 10 -> 10.10.10.2:http Tunnel 10 0 18 -> 10.10.10.3:http Tunnel 10 0 3 -> 10.10.10.4:http Tunnel 10 0 10 -> 10.10.10.5:http Tunnel 10 0 5 If I do ipvsadm -Lnc then I see lots of connections but only ever in ESTABLISHED & FIN_WAIT states. I was using ldirectord previously on a Gentoo based load balancer and the activeconn used to be accurate, since moving to Ubuntu 10.4 LTS something seems to be different. # ipvsadm -v ipvsadm v1.25 2008/5/15 (compiled with popt and IPVS v1.2.1) So, is ipvsadm not tracking active connections properly and thus making load balancing work incorrectly and if so, how do I get it to work properly again? Edit: It gets weirder, if I cat /proc/net/ip_vs then it looks like the correct activeconns are there IP Virtual Server version 1.2.1 (size=4096) Prot LocalAddress:Port Scheduler Flags -> RemoteAddress:Port Forward Weight ActiveConn InActConn TCP B86A9732:0050 rr -> 0AB42453:0050 Tunnel 10 1 24 -> 0AB4321D:0050 Tunnel 10 0 23 -> 0AB426B2:0050 Tunnel 10 2 25 -> 0AB4244C:0050 Tunnel 10 2 22 -> 0AB42024:0050 Tunnel 10 2 23

  Read the article

• SQL 2008 Reporting Services Report Manager blank on Win 7

  - by Daniel Root

  I have installed SQL Server 2008 Reporting Services on my development laptop running windows 7. When I browse to the report manager, only the header is shown. The content pane is blank, and there is no 'Site Settings' option, New Folder options, etc. I found plenty of similar stories about SQL 2005, and then the fix was to manage permissions in the virtual directory in IIS. However, in 2008, there is no virtual directory - RS manages this outside of IIS. Per other serverfault articles, I've tried the following: adding my account to the reporting services group changing the service to run as local system made sure localhost was trusted site in IE ran IE as admin installed SQL Server 2008 SP1 There are no errors in the event viewer. Perhaps related, if I browse to the webservice, I also get the error: The permissions granted to user 'Computer\User' are insufficient for performing this operation. (rsAccessDenied)

  Read the article

• Website requests not reaching IIS?

  - by pete the pagan-gerbil

  To start off with a confession, I am not a server admin - just a developer tasked with getting to the root of a problem. Please be gentle! I have an intranet ASP.NET website running in IIS on a virtual machine. The website is not accessed very often (the last IIS log file was modified nearly six months ago). Both the IP address and Host header value are now failing to return the website, and the IIS log still doesn't show any more recent activity. The virtual machine was moved to a different physical location a few months ago, and the IP address for it has changed. Could this be what has broken access to the site? What else should I be checking to solve this? I don't have totally unrestricted access to the building's network settings, structures, etc. I would be grateful for any advice, even if I can't use it myself it'll improve my knowledge of what's going on behind the scenes!

  Read the article

• How to setup a simple self-hosted dynamic DNS server

  - by Cerin

  I have a small internal network of physical machines running hypervisors, which in turn run several KVM Ubuntu virtual machines. How would I setup an internal dynamic DNS server so that when I run a script to create a new virtual machine, that VM could automatically register itself in the DNS server? Bind seems to be the standard DNS server for Linux, but it seems designed for a much more "static" DNS model. Dynamically updating this would require a complicated script that would have to SSH into the DNS server, edit configuration files, and then restart the server. This doesn't seem like a very elegant solution. Are there better options? I saw a similar question, although they're asking for a solution for a public setting on Amazon. My servers are entirely private, and I don't want to rely on an external VM host or Dynamic DNS provider.

  Read the article

• Getting rid of Plesk on a VPS

  - by TomA

  I've been using a relatively expensive VPS for hosting about 30 domains and I want to migrate to a cheaper one, without Plesk. Both use CentOS. My users will not care, they don't use Plesk anyway. But I will not be able to use it for creating new virtual hosts, FTP accounts etc. I'm not a commandline guru, esp. not in a server environment. Is there a free Plesk alternative for these purposes? I need to: Create a new virtual host with it's own FTP account Setup some basic FTP quota I don't need: DNS management (the new VPS service has an external DNS management GUI) Mail server management (I use Google Apps) Any suggestions welcome, from Plesk alternatives to "RTFM" or links to tutorials.

  Read the article

• How to setup anonymous access in WinSSHD

  - by Shrike

  I have a Windows server (Win2008R2) with WinSSHD installed. I need to allow anonymous access to a particular folder on the server. Actually it's a git repositiory for bower registy but it doesn't matter. I want WinSSHD allow me to connect to an endpoint like "ssh://[email protected]/" I've created a virtual user "bower" with password only auth. No keys. But if I leave empty password then WinSSHD doesn't allow connection with error "Incorrect virtual account password". How to setup a SSH access without any authentication?

  Read the article

• How can I apply a DSP to my microphone in windows?

  - by user16315

  I'd like to be able to run my microphone through arbitrary DSP filters--Mostly for compression and amplification, but also noise cancelation would be nice. I'd then like to take that output and put it back in a virtual audio device that I could use as input for skype, mumble, teamspeak, or any other VOIP program. With a program like Virtual Audio cable, I can do the 'fake devices' part but as far as I know it does not allow any kind of filtering inline. Does a program like this exist? Or some combination of programs that can be combined to accomplish this?

  Read the article

• Getting MSExchange transport Error on Server 2003 SP2

  - by Scott

  I am getting the following Error messages and do not know how to fix it. Event Type: Error Event Source: MSExchangeTransport Event Category: (8) Event ID: 3017 Date: 4/29/2010 Time: 1:21:12 PM User: N/A Computer: NETSRV Description: A non-delivery report with a status code of 5.3.5 was generated for recipient rfc822;[email protected] (Message-ID <19104335.51321272561635734.JavaMail.SYSTEM@PARROT). Causes: A looping condition was detected. (The server is configured to route mail back to itself). If you have multiple SMTP Virtual Servers configured on your Exchange server, make sure they are defined by a unique incoming port and that the outgoing SMTP port configuration is valid to avoid looping between local virtual servers. Thanks for any help you can provide.

  Read the article

• Cannot remove wireless network profile even though admin account is used

  - by David Karlsson

  On my windows computer which is connected to a company domain. I have problems with the wireless networking. First of all the computer fails to connect. Second of all I cannot remove the network from the list of wireless profiles. The properties window simply claims that "This network is administered by the Administartor Account". I am currently logged in as the local administrator. I have also tried creating a new admin account and still get the same problem when trying to remove the network. My computer has only the microsoft security essentials antivirus and some VMWare+virtual box connections that I can figure might interfere, but disabling realtime protection has not helped me on this. I also cannot delete the virtual network adapters from the control panel / network adapters...

  Read the article

• Is there any way to isolate the python2.7 , mod_wsgi installation from main environment

  - by user31

  I have many local virtual machines for building the django websites. I find it very hard to configure all the machines with mod_wsgi , python and all that installation issues. Is there any way that i can install even python 2.7 , mod_wsgi etc and all that inside the virtual environment folder so that i can just copy paste that folder in my live server and i don't need to mess with mos_wsgi , python 2.7 and other issues. Is it possible or even any close variation of that so that puting the site to live servers is very easy and everything which is needed by site should be included locally I also face many problems when i need to move the django sites across servers

  Read the article

• Installing Yaws server on Ubuntu 12.04 (Using a cloud service)

  - by Lee Torres

  I'm trying to get a Yaws web server working on a cloud service (Amazon AWS). I've compilled and installed a local copy on the server. My problem is that I can't get Yaws to run while running on either port 8000 or port 80. I have the following configuration in yaws.conf: port = 8000 listen = 0.0.0.0 docroot = /home/ubuntu/yaws/www/test dir_listings = true This produces the following successful launch/result: Eshell V5.8.5 (abort with ^G) =INFO REPORT==== 16-Sep-2012::17:21:06 === Yaws: Using config file /home/ubuntu/yaws.conf =INFO REPORT==== 16-Sep-2012::17:21:06 === Ctlfile : /home/ubuntu/.yaws/yaws/default/CTL =INFO REPORT==== 16-Sep-2012::17:21:06 === Yaws: Listening to 0.0.0.0:8000 for <3> virtual servers: - http://domU-12-31-39-0B-1A-F6:8000 under /home/ubuntu/yaws/www/trial - =INFO REPORT==== 16-Sep-2012::17:21:06 === Yaws: Listening to 0.0.0.0:4443 for <1> virtual servers: - When I try to access the the url (http://ec2-72-44-47-235.compute-1.amazonaws.com), it never connects. I've tried using paping to check if port 80 or 8000 is open(http://code.google.com/p/paping/) and I get a "Host can not be resolved" error, so obviously something isn't working. I've also tried setting the yaws.conf so its at Port 80, appearing like this: port = 8000 listen = 0.0.0.0 docroot = /home/ubuntu/yaws/www/test dir_listings = true and I get the following error: =ERROR REPORT==== 16-Sep-2012::17:24:47 === Yaws: Failed to listen 0.0.0.0:80 : {error,eacces} =ERROR REPORT==== 16-Sep-2012::17:24:47 === Can't listen to socket: {error,eacces} =ERROR REPORT==== 16-Sep-2012::17:24:47 === Top proc died, terminate gserv =ERROR REPORT==== 16-Sep-2012::17:24:47 === Top proc died, terminate gserv =INFO REPORT==== 16-Sep-2012::17:24:47 === application: yaws exited: {shutdown,{yaws_app,start,[normal,[]]}} type: permanent {"Kernel pid terminated",application_controller," {application_start_failure,yaws,>>>>>>{shutdown,>{yaws_app,start,[normal,[]]}}}"} I've also opened up the port 80 using iptables. Running sudo iptables -L gives this output: Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT tcp -- ip-192-168-2-0.ec2.internal ip-192-168-2-16.ec2.internal tcp dpt:http ACCEPT tcp -- 0.0.0.0 anywhere tcp dpt:http ACCEPT all -- anywhere anywhere ctstate RELATED,ESTABLISHED ACCEPT tcp -- anywhere anywhere tcp dpt:http ACCEPT tcp -- anywhere anywhere tcp dpt:http Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination In addition, I've gone to the security group panel in the Amazon AWS configuration area, and add ports 80, 8000, and 8080 to ip source 0.0.0.0 Please note: if you try to access the URL of the virtual server now, it likely won't connect because I'm not running currently running the yaws daemon. I've tested it when I've run yaws either through yaws or yaws -i Thanks for the patience

  Read the article

• LM Sensors always returning same (invalid) value for one temp sensor

  - by pkaeding

  I am trying to monitor the temp sensors on a server, and plot them using Cacti. I have lm-sensors installed and working correctly. For example, here is the output from sensors: % sensors acpitz-virtual-0 Adapter: Virtual device temp1: +26.8 C (crit = +100.0 C) temp2: +32.0 C (crit = +60.0 C) coretemp-isa-0000 Adapter: ISA adapter Core 0: +36.0 C (high = +105.0 C, crit = +105.0 C) coretemp-isa-0001 Adapter: ISA adapter Core 1: +42.0 C (high = +105.0 C, crit = +105.0 C) However, when I try to get this data via SNMP, I get only one sensor's temperature correctly, and another one always returns 100.000 C: % snmpwalk -Os -c public -v 1 10.8.0.18 -m ALL lmTempSensors lmTempSensorsIndex.1 = INTEGER: 0 lmTempSensorsIndex.2 = INTEGER: 1 lmTempSensorsDevice.1 = STRING: temp1 lmTempSensorsDevice.2 = STRING: temp1 lmTempSensorsValue.1 = Gauge32: 26800 lmTempSensorsValue.2 = Gauge32: 100000 So, my question is two-fold: Why is the second sensor that is returned by SNMP giving a value of 100 C (when it should be 32 C) Why are my CPU core sensors not being returned by SNMP?

  Read the article

• Hylafax and "No response to MPS"

  - by Joril

  We have an Hylafax 5.2.5 CentOS 5 installation hosted inside a Xen virtual machine. It works quite well, but now I'm in the process of upgrading/migrating it to a KVM virtual machine running Ubuntu 10.04 and Hylafax 5.5.1 (compiled from source using http://sourceforge.net/projects/hylafax/files/hylafax%20debian%20build%20files/ ) The problem I'm having is that - while receiving works fine - sending faxes is extremely unreliable, I get lots of "No response to MPS repeated 3 tries", or "Failure to transmit clean ECM image data." The line, modem and configuration files I'm using are the same as before, so I thought that it could be a KVM scheduling issue, but even setting cpu_shares to 10240 instead of 1024 doesn't change a thing... What else could I try? Here's an example log file http://pastebin.com/cN01cpEs

  Read the article

• VMWare-Tools Installation fails on Ubuntu 11.04

  - by Ajay

  I am trying to install VMwareTools-8.4.6-385536.tar.gz (VMWare Tools) on the following operating system: Ubuntu 11.04 - Linux ubuntu 2.6.38-8-generic #42-Ubuntu SMP Mon Apr 11 03:31:50 UTC 2011 i686 i686 i386 GNU/Linux I am using VMPlayer version 3.1.4 - build 385536 ==================================================================== After starting the installation i am getting the following errors: What is the directory that contains the init scripts? [/etc/init.d] Error opening No such file or directory ================================================ Distribution provided drivers for Xorg X server are used. Skipping X configuration because X drivers are not included. Creating a new initrd boot image for the kernel. update-initramfs: Generating /boot/initrd.img-2.6.38-8-generic Starting VMware Tools services in the virtual machine: Switching to guest configuration: done Blocking file system: done Guest operating system daemon: failed Virtual Printing daemon: done Unable to start services for VMware Tools Can somebody help in this?

  Read the article

• Ghost Image - windows asks for activation on when deployed to VM

  - by Chris Sobolewski

  I have several images created with Ghost Solution Suite (v11 I believe), the images have been in use for a few years now, but I am finally to the point where I have enough time to attempt to virtualize them for easier updates. I am running VMWare and attempting to image the virtual machines with my ghost image files. For my images I am running sysprep with minisetup and using reseal. The image deploys successfully, however when I start the VM for the first time, it demands windows activation. This doesn't happen when I image a physical computer, even a different model with different hardware. The idea of virtualizing my images becomes rather worthless if I am unable to deploy the images without having to activate every time (especially as Microsoft keeps declaring our volume licence key as invalid for activations). Does anyone know why it is asking for activation on a virtual machine, but not a physical PC? How can I prevent this?

  Read the article

• Rebooting Guest OS on a Hyper-V 2008 R2 Cluster results in a Shutdown

  - by S_Kuwahara

  Hi Folks, I have an interessting issue here. Sometimes when I manually reboot some of my guest OS (W2K3 / W2K8) on my Hyper-V 2008 R2 Cluster it does not reboot, it just shuts down. When I'm talking about a manual reboot, I mean connecting with RPD to the virtual server and use the shutdown funktion in the OS itself. I than have to start the virtual machine again via SCVMM / Hyper-V manager and it works just fine. There is nothing special in the eventlog of the host or guest OS. There is also nothing special logged in SCVMM. The guest OS all have the integration tools installed. Any hints? Thanks in Advance

  Read the article

• Customized windows xp installation

  - by user23950

  How to create a customized version of an xp installation cd. I want a hand's off installation that will install all the themes, drivers , and applications I need without my intervention. How can I do that. I tried to make use of this software called Nlite. But when I tested the iso file using virtual box. The virtual box said that there's a certain file that cannot be copied. And by the way, before I customized the original iso image of windows xp sp3, it doesn't have the file copying problem that I mentioned above.

  Read the article

• Windows Server 2008 hangs up while booting

  - by Jim R

  Windows Server 2008 hangs up while booting after Windows update applied several updates. The server is a virtual instance on a Server 2008 Hyper-V host. Other virtual servers are fine, but have not been updated. The normal boot shows the horizontal barber poll forever. When I do a safe boot it also hangs up. With a "Please Wait..." after loading many '.sys' files. The last successfully loaded file listed is: '\Windows\system32\drivers\crcdisk.sys' That is the extent of what I have been able to determine.

  Read the article

< Previous Page | 185 186 187 188 189 190 191 192 193 194 195 196  | Next Page >