Search Results

Search found 27766 results on 1111 pages for 'bad idea jeans'.

Page 19/1111 | < Previous Page | 15 16 17 18 19 20 21 22 23 24 25 26  | Next Page >

  • Reverse proxy 502 bad gateway

    - by Brian Graham
    I have setup a subdomain to proxy my plesk panel, but when saving pages I am getting 502 Bad Gateway error instead of a completion message. I am running CentOS 6. Here is my vhost.conf configuration for http://plesk.domain.tld/: RewriteEngine On RewriteCond %{SERVER_PORT} ^80$ RewriteRule $ https://plesk.domain.tld/ [R,L] Here is my vhost_ssl.conf configuration for https://plesk.domain.tld/: SSLProxyEngine On <Location /> ProxyPass https://localhost:8443/ ProxyPassReverse https://localhost:8443/ </Location> I have more than enough (and I have even checked) RAM, CPU and HDD. There are no spikes. As well, the posted information does save, it just errors when trying to show me a "This information has been saved." green/red block. Here is the relevent error from /var/log/nginx/error.log (IP/Host Filtered): 2014/05/29 02:42:41 [error] 8046#0: *402 upstream prematurely closed connection while reading response header from upstream, client: 173.238.XX.XX, server: plesk.domain.tld, request: "POST /smb/web/edit HTTP/1.1", upstream: "https://198.100.XX.XX:7081/smb/web/edit", host: "plesk.domain.tld", referrer: "https://plesk.domain.tld/smb/web/edit"

    Read the article

  • Bad sound quality of 3.5mm headphone with mic on laptop

    - by Isaac
    I have a set of headphones that have a built-in mic for hands-free calling. They just work great on my Sony Ericsson Cedar cellphone. The problem is that when I connect headphone to my Dell N5010 laptop to listen to music, the quality is horrible, with very weak or no vocals. They funny part is when I hold down the talk button on the mic (headphone mic), at which point it sounds great, but goes back to bad quality as soon as I release talk button. Also, when I take out the jack a little, at some point, the sound is great but I have to hold the jack there. I looked for any configuration on the sound card driver but find nothing. Besides using a glue to hold down the talk button of mic :), is there any other solution?

    Read the article

  • Bad request - Invalid Hostname Error when using ARR IP address

    - by syloc
    I'm trying to setup a simple ARR system. I have 1 ARR machine load balancing between 2 APP servers. I can reach the app sites if i use the server name of the ARR machine. (http://arrserver/app) But i can't do it with its IP address. (http://10.7.10.25/app). It gives the "Bad Request - Invalid Hostname". In the ARR machine i configured the default site's bindings to "All Unassigned","80" (default values). Do i need to change the binding rule or need additional url rewrite rules? And also, in the ARR server http://127.0.0.1/app doesn't work. But http://localhost/app works fine. Thx in advance

    Read the article

  • MediaTemple Django Bad Gateway

    - by Eeyore
    I have a site running on GS server on MediaTemple. It's Django/PostgreSQL setup. For some reason from time to time I get Bad Gateway error and I can't figure out what's causing it. What can cause this error? What else can I do to find the cause of the problem? url.access-deny = ( "~", ".inc" ) fastcgi.server = ( "/main.fcgi" => ( "main" => ( "socket" => "/var/tmp/" + appname + ".sock", # don't change this "check-local" => "disable", ) ) ) alias.url = ( "/media/" => "/home/xxx/data/python/django/django/contrib/admin/media/", "/static/" => "/home/xxx/containers/django/site/static/", ) url.rewrite-once = ( "^(/media.*)$" => "$1", "^(/static.*)$" => "$1", "^/favicon\.ico$" => "/media/favicon.ico", "^(/.*)$" => "/main.fcgi$1", ) server.error-handler-404 = "/main.fcgi"

    Read the article

  • Does a bad Internet connection increase bandwidth usage?

    - by Synetech
    My (Rogers) cable connection has been pretty bad recently (channels 3 and 10 are particularly fuzzy—it’s analog, not digital cable). Not surprisingly, this has caused my cable modem to drop out and have to reestablish a connection a couple of times since it started. The poor connection of course means higher corruption (not necessarily dropped per se) which causes the TCP/IP stack to have to retransmit packets more often. Reduction of bandwidth throughput aside, I got to wondering if it increases the actual bandwidth usage. That is, if there is a high error rate on the line causing packets to have to be retransmitted: Does this increase a bandwidth monitoring program’s numbers? Does the ISP count the retransmitted packets toward the monthly cap? Based on what I remember from my university networking courses and common sense, I have a feeling that the answer to both questions is yes, but I cannot reliably measure the first, and have no authoritative answer for the second. I’m wondering if maybe the retransmitted packets are acknowledged as being duplicates and thus not counted somewhere along the line.

    Read the article

  • Dell Power Edge R515 - Replacing a Bad Hard Drive in a RAID

    - by LonnieBest
    I've ordered a new hard drive to replace a bad one in a Dell Power Edge R515. The manual covers obvious topics regarding physical replacing of hard drives, but I've never done this before on a production server where RAID is involved. I've heard people talk about this topic, and I've heard that some servers have RAID controllers that are smart enough to allow you to just put in the new drive (hot swap), and then the server will know automatically how to rebuild that drive to be what the old one was to the system. Where do I find the proper procedure for replacing a failed hard drive on a live production Dell Power Edge R515? Can someone with experience tell me how easy or hard this usually is?

    Read the article

  • In Windows Vista, when starting any and every program, a "bad image" error is generated

    - by Mark Hatton
    I have a problem where any program is started under Windows Vista, the following error message is generated Bad Image C;\PROGRA~1\Google\GOOGLE~3\GOEC62~1.DLL is either not designed to run on Windows or it contains an error.Try installing the program again using the original installation media or contact your system administrator or the software vendor for support. This happens for every program started, including those that start automatically at boot time. My Google-fu is failing to solve this for me. I have already tried an "sfc /scannow" which did find some problems, but it said that it could not correct them. What might cause this problem? How might it be resolved?

    Read the article

  • "Unknown user name or bad password" when I launch ADUC

    - by Chris
    When I open up Active Directory Users and Computers from my workstation, I receive an error: Naming information cannot be located because: Logon failure: unknown user name or bad password. Contact your system administrator to verify that your domain is properly configured and is currently online. If I log in to my workstation as somebody else, it works. If I log into a different workstation using my account, it works. All the workstations in question are running Windows Vista (32 and 64 bit) or Windows Server 2008. The domain controller in question is running Windows Small Business Server 2008. Everything else (that I tried) in the Remote Server Administration Tools runs just fine. Any thoughts? Edit: I just tried reinstalling RSAT. No such luck.

    Read the article

  • bad switchs duplicate my ip

    - by tacoen
    I had a large area LAN. There were many switch and AP on it, then somehow I couldn't ping my servers, and it's said that the IP was duplicated. I use arpwatch and found out that one of the switch flip-flop-ing the IP. I isolated that troublesome switch using his mac-address. But, since this a large area LAN... I doubt this will be the last cases. If there any software or hardware that I can use to prevent this kind of error? Sorry for my bad English.

    Read the article

  • how to set up domain name, bad request invalid hostname

    - by user45645
    assume i have a domain name which will be forwarded to my public ip (web server) automatically. in IIS 6, ip is public ip port is 6666, advanced - host value is www.hello.com firewall is open for 6666(web server port) and 53(DNS port), DMZ of router is my physical address in DNS, i have already had a zone called oldhello.com. And i expect a new domain name. So i have addded a new zone called hello.com and checked SOA server (P) is one.hello.local. then added a new host called one, full name is one.hello.com, ip address 192.168.7.3(my address in router) and then add a alias(CNAME) www, full name is www.hello.com, FQDN i choose the host i added before (one.hello.com) i expected that when i type the public ip in browser, can it be changed to domain name automatically. if not set host value www.hello.com, use public ip i can see the web however, after set up host value www.hello.com, browser show bad request invalid hostname

    Read the article

  • Seagate 1TB 'EXPANSION' external hard drive, showing as BAD

    - by Dave Plews
    Hello! I have bough an external Seagate 1TB drive, which my XP system can see and will write files to, however when I use Partition Magic it describes the whole partition as BAD, and it is shown in yellow. All the options are greyed out. When I use Drive Image XML to try and copy drive to drive (I want a comlplete copy of my C drive including OS), I get an error message saying it can't lock the drive. The external drive is brand new and uses NTFS. Any ideas? Seagate 'support' haven't bothered getting back to me. Incidentally, I have another external drive (320GB), which uses FAT32 and Partition Magic sees that fine. I am doing a full format of the Seagate at the moment, to see if this helps. Thanks in advance!

    Read the article

  • Bad password when logging in via Remote Desktop

    - by Shiraz Bhaiji
    I have just setup a windows 2003 server running in hyper-V. When I log in via Hyper-V it works fine. When I try to login via remote desktop I get a bad user name or password error. I have: Disabled the firewall Enabled remote connections Before I did the above I did not get to the login screen. I can ping the ip address of the image. I am trying to login as Administrator. Anyone have an idea about how to fix this? Edit I have now managed to fix this by changing the password to something without special characters. Strange thing is the I could not see any problems with the passord, had tried typing it into the user name field to check it.

    Read the article

  • Do I have a bad SD card?

    - by User1
    I'm trying to copy data from my computer to an SD card. After a few hundred megs, I keep getting the following errors in dmesg: [34542.836192] end_request: I/O error, dev mmcblk0, sector 855936 [34542.836284] FAT: unable to read inode block for updating (i_pos 13694981) [34542.836306] MMC: killing requests for dead queue [34542.836310] end_request: I/O error, dev mmcblk0, sector 9280 [34542.837035] FAT: unable to read inode block for updating (i_pos 148486) [34542.837062] MMC: killing requests for dead queue [34542.837066] end_request: I/O error, dev mmcblk0, sector 1 [34542.837074] FAT: bread failed in fat_clusters_flush [34542.837085] MMC: killing requests for dead queue These were all files I copied from a smaller SD card. I just want to transfer them to my new, larger card for my phone. I tried the same experiment with different files on a different machine and the card failed again. Reading data from the old card went fine. My systems are older and the new SD card is new (16GB Class 4). Could this be that my computers are too old? Is there a definitive test to verify if my SD card is bad?

    Read the article

  • Do I have a bad video card?

    - by zooropa
    I think this is the right spot to post this question. Please don't flame me if it isn't. My work computer is a Dell Prescision M6400 laptop. I use the VGA output to a second monitor. There is something wrong with my second monitor's output. Here is a screenshot of my desktop. You can see fragments of the right side of a Windows File Explorer window in the image. Is this a bad video card?

    Read the article

  • “BAD” partition showing up in Partition Manager

    - by Quintin Par
    I tried to partition my primary hard disk (NTFS partitions) with qtparted and got stuck in the process. Consequently I had to kill the process and exit my knoppix live CD boot up. Even though I was expecting XP to get corrupted, it booted fine and showed up all the drives accessible. But when I opened this with partition manager 8, it shows up as “BAD”. I ran chkdsk /f without any success. My objective with qparted and partition magic was to resize my existing partitions and add some space to c: How do I fix this problem and resize my partitions? Edit: Here's how my primary drive as per Windows is:

    Read the article

  • IntelliJ 12 - Grails Distribution in specified path is broken

    - by Prayag Upd
    I am struggling to configure grails 2.3.X in IntelliJ idea 12. Grails 2.2.X is configured successfully. Grails 2.3.2 is working properly from terminal. I can compile, test, run my application. But while trying to configure it in IntelliJ so that dependencies get resolved, I get the IntelliJ shouting straight to me(as pictured below). Looks like Grails Distribution in specified path is broken. Cannot determinate version. What I see is changes in grails-2.3.x/dist/ to earlier version's grails-2.2.x/dist/. Is this because there's no support for newer version(2.3.x) of grails in IntelliJ 12 or what ? I want nothing else but my application (jar) dependencies to be resolved in the IDE.

    Read the article

  • Intellij Community can't use http proxy for Maven

    - by MikeHoss
    I have Intellij IDEA Community installed on a Linux box that needs to use an authenticated proxy to get to the Internet. I have a system-wide proxy on the box that works, and I have the proxy configured in ~/.m2/settings.xml. Maven correctly uses the proxy when I run try it from the command-line. I have the same proxy configured within Intellij and it gives me the plugins listing correctly. But when I try to sync with the Maven repository withing Intellij I keep getting this: [WARNING] Unable to get resource 'org.codehaus.mojo:hibernate3-maven-plugin:pom:2.2' from repository restlet (http://maven.restlet.org): Authorization failed: Not authorized by proxy. I went to Settings-Maven and put in the proxy info as properties and that didn't work. I can see by looking at those settings that Intellij is reading my ~./m2/settings.xml fine because it knows where my local repo is (it's in a non-standard place). Anyone know how I can get this working?

    Read the article

  • Intellij + GWT 2: Development Mode ignores changes to static content

    - by Kaffeine Coma
    The new Development Mode in GWT 2 is awesome, but unfortunately as launched from Intellij IDEA 9, it does not seem to notice changes made to static files such as html, css, etc. It immediately see changes in *.java files, but not the static ones. If I make a change in a static file I need to quite the Development Mode tool and re-launch it. This is painfully slow, and negates much of the point of using dev mode in the first place I assume this is some artifact resulting from the way the Intellij runner launches it- it creates an out/artifacts/project_war_exploded directory with the static content and class files. How can I get Intellij Dev Mode tool to follow changes made to the original static source files?

    Read the article

  • Using @NotNull in a project where both IntelliJ and Eclipse developers are working

    - by Gugussee
    A co-worker on IntelliJ IDEA (working on another project) showed me the amazing @NotNull annotation. I've read messages here on SO about how starting to add @NotNull everywhere saved lots of time and headaches (and IntelliJ 10 can even add automatically @NotNull to old code when it detects that null would break havoc). Since I read my first "Probable @NotNull violation" message (in real-time, in the IDE, even on a partial .java file that doesn't compile yet) my jaw dropped and I got hooked. So I was wondering: is there anything that needs to be known if we want to start using @NotNull in a project where developers are using both Eclipse and IntelliJ? I know IntelliJ ships with the annotations.jar. Is this compatible with Eclipse?

    Read the article

  • Intellij UML diagram does not show one to many relationships

    - by Calm Storm
    I am trying to follow http://www.jetbrains.com/idea/features/uml_class_diagram.html I have a few classes so when I do Ctrl + Alt + U I only see all classes and just Extends relationships. Please note that I have set the "Diagrams" options in my settings to show one to many etc. I do not see One to One, One to Many relationships at all ? I have used JPA OneToOne Annotations and they dont turn up at all? Pressing Ctrl Shift F12 does not do anything? Can someone please explain?

    Read the article

  • How to avoid wasting time during compilation during development?

    - by user259576
    Hello, I'm working with a small team of developers. My job is to convert a Make project (with Intellij Idea 9.0) into a Maven 2 project. The problem is : we spend a lot of time during the development. With Make, only one complete build was required and then any change did not consume a lot of time (almost instantaneously). On the other hand, with Maven 2, a little change takes a lot of time to run. Any solution ? Thanks.

    Read the article

  • What features do you miss most when switching from IntelliJ to XCode ?

    - by Ori
    Hi, I've started to use XCode several months ago, after using IntelliJ for several years, and there are quite a few features that I really miss. XCode is not that bad, but it is lacking some basic stuff. To trigger the discussion, here are some of the features that I miss most, who knows maybe someone from Apple will bump into this post and steal some Ideas :) Source-level error-highlighting. The write-compile-fix cycle feels like going back in time 15 years ago to my early C days. Many errors can be spotted without having to compile and Java IDEs have been doing it for years. A decent debugger. This is a bit unfair because IntelliJ's debugger is the best I've used so far, but XCode's debugger is at least 5 years behind and Apple has a few more developers than JetBrains... Stronger re-factoring. A no-brainer I guess. XCode has some renaming capabilities (which they call re-factoring), but they are very few. Override method. This one is really amazing. XCode doesn't have an "override method" command which lets you choose the method you want to override from a super class or protocol. You need to go to the documentation or header file and start copy-pasting. Duplicate selected line(s). I've bumped into some posts that offer workarounds for this via custom key-binding, but none of them works, at least for me. Go to last edit point. Bummer! Come on Apple, this one is so easy to implement and so useful! A better open quickly feature. IntelliJ's quick find of classes/files/text is so much better... Turns out that my list goes on and on, so I'll stop here... What other features do you miss most in your transition to XCode?? Ori

    Read the article

  • IntelliJ Doesn't Notice Changes in Interface

    - by yar
    [I've decided to give IntelliJ another go (to replace Eclipse), since its Groovy support is supposed to be the best. But back to Java...] I have an Interface that defines a constant public static final int CHANNEL_IN = 1; and about 20 classes in my Module that implement that interface. I've decided that this constant was a bad idea so I did what I do in Eclipse: I deleted the entire line. This should cause the Project tree to light up like a Christmas tree and all classes that implement that interface and use that constant to break. Instead, this is not happening. If I don't actually double-click on the relevant classes -- which I find using grep -- the module even builds correctly (using Build - Make Module). If I double-click on a relevant class, the error is shown both in the Project Tree and in the Editor. I am not able to replicate this behavior in small tests, but in large modules it works (incorrectly) this way. Is there some relevant setting in IntelliJ for this?

    Read the article

  • apache2: bad user name www-data

    - by Robert Ross
    Starting web server apache2 apache2: bad user name www-data I just tried restarting my webserver because of an update I did to my php.ini and originally I was getting something about the PID file being overwritten. Now I just get this: * Starting web server apache2 apache2: bad user name www-data this has NEVER happened before, and I haven't changed and permissions or apache2 configuration files. What gives?

    Read the article

  • Database with "Open Schema" - Good or Bad Idea?

    - by Claudiu
    The co-founder of Reddit gave a presentation on issues they had while scaling to millions of users. A summary is available here. What surprised me is point 3: Instead, they keep a Thing Table and a Data Table. Everything in Reddit is a Thing: users, links, comments, subreddits, awards, etc. Things keep common attribute like up/down votes, a type, and creation date. The Data table has three columns: thing id, key, value. There’s a row for every attribute. There’s a row for title, url, author, spam votes, etc. When they add new features they didn’t have to worry about the database anymore. They didn’t have to add new tables for new things or worry about upgrades. This seems like a terrible idea to me, but it seems to have worked out for Reddit. Is it a good idea in general, though? Or is it a peculiarity of Reddit that happened to work out for them?

    Read the article

< Previous Page | 15 16 17 18 19 20 21 22 23 24 25 26  | Next Page >