Search Results

Search found 9688 results on 388 pages for 'external hdd'.

Page 19/388 | < Previous Page | 15 16 17 18 19 20 21 22 23 24 25 26  | Next Page >

  • How to utilize 4TB HDD, which is showing up as 2.72TB

    - by mason
    I have two internal HDD's. They're both 4TB capacity. They're both formatted with the GPT partitioning scheme, and they're Basic Discs (not dynamic). I'm on Windows 8 64bit. I have UEFI, not BIOS. When I view the discs in Computer Management MMC with Disk Management, they show that each partition is formatted as NTFS and takes up the entire drive. And it shows that each drive has a capacity of 3725.90GB in the bottom section of Disk Management, but 2.794.39GB in the top section. When I view the discs in "My Computer"/"This PC" they only show up as 2.72TB, which matches the amount capacity I'm getting from some other 3TB HDD's I have. Why are they showing up as only 2.72GB? Will I be able to use the full 4TB capacity? Also of note, although I'm not sure it's relevant: I often get corrupted files on these two HDD's. None of my other HDD's give me corrupted files. Usually the problem is fixed by running chkdsk /f on the drives, but it's extremely annoying. In the picture below, it's the X: and Y: drives. Steps I've tried Flashed latest BIOS (MSI J.90 to K.30)

    Read the article

  • HDD cannot be booted from

    - by K.Wong
    I have an ASUS A52F, no mods, with Win7 preinstalled. There is one hard drive, two partitions, one for the OS (C:) and one for data (D:) After laptop trauma, i.e. I dropped it, it still worked fine. However, when chkdisk was run on the C: drive chkdisk crashed, and Windows is unbootable. Windows Startup Manager utility was run, but error code 0xc00000e9 was given. Windows help db shows that this is a BIOS problem, however in BIOS setup the drive can be accessed, and folders can be shown. I also burned a Ubuntu 12.04 distro, and booted off it, but my internal HDD is missing and cannot be accessed. When installation program is run the HDD shows up as a location to install to yet the drive is shown as blank. tl;dr: HDD damaged, chkdisk crashed. Windows 7 is unbootable. Given error code, according to Microsoft db, is a BIOS problem, yet in BIOS the drive is accessible. different OS (Ubuntu 12.04), booted off a distro, yet HDD is inaccessible. Quick help appreciated.

    Read the article

  • SATA HDD stuttering on reads (LED on)

    - by jdehaan
    I hope I can get some new ideas to solve the issue. What I have: AMD Phenom II X4 905e Box, Sockel AM3 Gigabyte GA-MA790XTA-UD4, AMD 790X, AM3 ATX WD Caviar GreenPower 1,5TB SATA II 4GB Kit OCZ DDR3 PC3-10666 Platinum Low-Voltage CL7 HIS HD 4670 iSilence4 DDR3 1024MB Native HDMI Dual-DVI, PCI-Express Behavior: Everything works normally excepting the HDD accesses. The drive seems to get stuck in reading data (LED drive by Mainboard is on for a while) then recovers and goes on. There is a delay of more than 30s sometimes. Often it is a matter of 5-10s. This does not seem related to the workload of the disk. What I tried so far: Use different SATA port: I switched from the SATA3 to SATA2 then the SATA driven by the CPU, no difference. Turned AHCI off, drove the SATA in IDE mode, same behavior, now I felt like the HDD has problems Deactivated energy saving settings (BeQuiet, ...), disabled 3 CPUs (msconfig) supposing some race condition or trouble with changing freqs, same trouble With Windows7 Professional 64Bit, I installed the hotfix http://support.microsoft.com/?scid=kb%3Ben-us%3B976418&x=8&y=9 with no success. The problem description matches what I experienced, so I felt lucky but was quite in a sad mood after being deceived. Burned the DLG 5.04f DataLifeGuard CD from WD to check the drive. All tests passed, to my surprise! Installed an Ubuntu on the same drive i386 flavour. Drive still in IDE mode, exactly the same behavior. So the OS does not matter. What I did not try yet: http://www.gigabyte.eu/Support/Motherboard/BIOS_Model.aspx?ProductID=3263 I have a F2 BIOS and there is a F3a Beta, did someone have similar issues that were solved by this update? It is a beta so I fear upgrading a bit and I could find no release notes at all on the net, not really serious work maybe they had issues translating from Chinese??? Using another HDD drive Does someone have other hints or a similar issue? Maybe it is neither the HDD nor the Mainboard/BIOS?

    Read the article

  • Recover LVM2 volume group after one HDD failed

    - by Bernd
    I had two HDDs, each one containing a LVM partition which formed a volume group. Then I had two LVs, one for my / directory and one for my /home/ directory. Yesterday where I had my / dir failed. I'm trying to recover at least my /home/ dir. What I've done so far: Boot a live system Extract LVM2 metadata from the working HDD using dd Copy metadata to /etc/lvm/backup/vg0 Now I'm trying to do this: pvcreate --restore /etc/lvm/backup/vg0 --uuid "[uuid of my working hdd]" /dev/sdb2 But I always get: Couldn't find device with uuid '[uuid of broken hdd]'. Couldn't find device with uuid '[uuid of working hdd]'. Device /dev/sdb2 not found (or ignored by filtering). I confirmed that /dev/sdb2 exists and I've commented out all filtering settings from /etc/lvm/lvm.conf so I don't know what might be causing pvcreate not to find the device. So: What might be the problem? Is it even possible to restore this partition? (As I'm writing this I'm starting to think it's impossible D:) Edit: Okay, looks like I've got it figured out. I was using a Ubuntu 8.10 CD (yeah, I know it's not supported anymore) and it seems that was the problem. When I started from a Ubuntu 10.04 CD everything worked 'fine', I could mount my LVM partitions partially without problems. (Will answer the question in 4 hours. But if anyone has still got some hints/tips, please share! :)

    Read the article

  • Bluescreen Stop 0x00000027 RDR_FILE_SYSTEM after cloning system on new HDD

    - by Daniel
    A couple of months ago I got a new 500GB HDD for my no-name-brand Laptop PC and I cloned the complete Win 7 Pro 32bit system with clonezilla from the old 70GB drive to the new one. At first everything was great, the new driver was immediately updated. But since then I get on a more and more frequent level (used to be every 2-3 days, but now it's more like 2-3 times a day) a BSOD Stop error. From the eventlog in Windows I know that there are two different error codes sppoking aroung: 0x00000027 (0xbaad0073, 0x9954f80c, 0x9954f3f0, 0x8ecd7c82) RDR_FILE_SYSTEM 0x00000044 (0x85443230, 0x00000eae, 0x00000000, 0x00000000) MULTIPLE_IRP_COMPLETE_REQUESTS I checked for viruses and did a complete HDD check using the Windows tool and WesternDigital tool (which is the producer of the new HDD) without results. I also looked for driver updates but couldn't find any. The name of the HDD as shown in the device manager is: WDC WD5000BPVT-00HXZT1 ATA Device. I'm really a noob regarding those kind of problems, so if you have any idea what I can try without losing all my data, let me know. Also, if any additional information are required.

    Read the article

  • External HDD connecting via USB disconnects wireless LAN connection

    - by Kensai
    Strange problem. I have this MEDION Akoya PC that has a dedicated bay to slide an external HDD sold separately. It's very handy indeed cause the slot is providing a fast USB 3 connection and power to the HDD unit, without extra cables. All works fine except this show-stopper behavior to disconnect me from the router once I slide in the unit and it powers up. The moment I connect the unit the (normally) three-four WiFi connections I see in my neighborhood disappear and my own to the router loses its signal strength (no Internet traffic is possible). After a while it throws me off that one as well, never to connect me again as long as the unit is powered. Once I disconnect the HDD the various signals come back and it automatically reconnects to my own. What takes? Are we in front of a serious design fault by MEDION here? Does the spinning of the HDD on top of the PC cause electromagnetic interference strong enough to throw off my WiFi connectivity? Is it a simple USB problem? Some kind of strange hardware conflict? Where should I look?

    Read the article

  • how do I get dual monitors to work properly in Ubuntu 11.10 on a Dell Latitude D630?

    - by wes cook
    I have spent a lot of time trying to get dual monitors to work on Ubuntu 11.10 on my Dell Latitude D630 (nVidia NVS 135m video card). - For starters, the System Displays settings app always only showed one unknown monitor, even though I had the external Acer monitor connected. - So I downloaded and installed the nVidia drivers. According to what I read I would need to only use the nVidia driver app (nVidia X Server Settings), so that's what I've done. (System Displays settings continued to only show a single monitor anyway). - nVidia settings app only showed on monitor until I changed the BIOS setting to use the onboard video for external monitor (not the dock video, which it was set to, even though I don't have a docking station). - The nVidia setting app now recognized both monitors. So, I setup the X Server display config as Separate X screen for both monitors. My laptop screen shows up as AUO 1440x900 and my external monitor as Acer E211H 1920x1080. - Everything seemed like it would work, but the external monitor was just a complete white screen. The external monitor was non-functional, even though sometimes it would show the background image - still nothing would show up over there. - So, I checked the Enable Xinerama box. - Now, after logging out and back in, the wallpaper extends to both screens but I get no taskbar at the bottom or top, no system menus, and I have to press the power button to restart or log off. - After experimenting with all the shells, the only one that shows the menus and taskbars when I log in is Gnome Classic. - This is pretty much the same symptoms as found here: How do I fix 11.10 GUI?. - So, I resign myself to the older shell. - Everything works fine until ... I unplug the external monitor ... this is a laptop after all. - Anyway, after doing some work on the road, I plug back in and I still see both screens and it's functional except, ... - Now, the laptop screen (with the taskbar and menu bar) has 4 black bars at the top that windows cannot cover. The top bar is the menu bar (with Applications, Places, the date and time and the system menu on the right). But the next 3 bars (the same height as the top menu bar) are empty and are just reducing the max size of windows on that screen. - See screenshot here: http://i39.tinypic.com/35d2kh1.png - So ... 1. How do I get rid of those extra 3 black bars? They're taking valuable screen space. 2. (less critical) How do I successfully use both screens in the Ubuntu or Ubuntu 2D shell?

    Read the article

  • Accidentally Changed Dual Monitor Setup and don't know how to reset it

    - by user203783
    I have a dual monitor setup with my laptop and an external Asus monitor running under Ubuntu 11.10. When I first started using Ubuntu, it synced both screens. What showed up on my laptop showed up on my eternal monitor. Last night, I accidentally knocked the HDMI cable from its port (not that unusual in the tight space I work in). When I plugged it back in, as usual, the external monitor only displayed my wallpaper. Usually, I just restart Ubuntu and it resets, but last night what I now realize was the display console came up and somehow I changed the setup. Now the two screens show different jobs so to speak. Also, the external monitor doesn't display the ribbon, making switching between Firefox tabs and windows or apps jarring. I write for a living and need to quickly check bits of research, notes or sources while writing and the extra switching between mouse pad and external mouse to get one or the other screen to respond interrupts my work flow. The only technical help I can offer is when the display console popped up, the graphical representation of the screens was that the external screen appeared layered over by about one-quarter of the laptop screen. Again, these were icons. I tried to replicate that after I obviously screwed things up. If someone could help. I would appreciate it. If I have to use terminal, that's fine. I started using computers for writing back when they were green DOS prompts. There's a certain elegance to prompt commands to me. Maybe it's the writer in me. Again, if anyone can help me return my screens to sync under Ubuntu 11.10, I would greatly appreciate it.

    Read the article

  • Access denied to external USB disk; update access rights fails in Windows 8

    - by gerard
    I use to work with 2 laptops (Windows vista and Windows 7), my work files being on an external usb disk. My oldest laptop broke down, so I bought a new one. I had no option other than take Windows 8. I suspect something changed with access rights, as my external disk suffered some "access denied" problem on Windows. I was prompted (by Windows 8) somehow to fix the access rights, which I tried to do, getting to the properties - security. This process was very slow and ended up saying disk is not ready Additionally, my external usb disk somehow was not recognized anymore. Back to Windows 7, I was warned that my disk needed to be verified, which I did. In this process, some files were lost (most of them I could recover from the folder found00x, but I have some backup anyway). Also, I don't know why, but under Windows 7, all the folder showed with a lock. Then back again to Windows 8. Same problem : access denied to my disk + no way to change access rights as it gets stuck disk is not ready". Now I am pretty sure there is some kind of bug or inconsistency in Windows 8 / Windows 7. I did 2. and 3. a few times. At some point, I also got an access denied in Windows 7. I could restore access rights to the disk to "System" (properties - security - EDIT for full control to group "system". ). But then I still get the same access right pb on Windows 8, and getting stuck in the process to restore full control to "system" -- and "admin" groups. I upgraded Windows8 with the Windows8 updates available. Does not help.

    Read the article

  • Method for imaging a HDD? [closed]

    - by Sonny Ordell
    Possible Duplicate: Imaging new hard drive in Windows 7 laptop? I have to image my 320gb Laptop HDD before I send it in for repairs. The HDD is likely going to get replaced, and I would ideally like to be able to restore everything as I have it now without having to reinstall my OSes, programs and place all my files back again. I can make space on an external HDD I have, so am just looking for how I should go about this. Should I just use dd with a linux rescue cd? Or is there perhaps a more suitable program with its own rescue disk?

    Read the article

  • Disable or sleep secondary HDD in Macbook

    - by cpak
    I've done some quick Googling but didn't find an answer. I've put an SSD in my Macbook, and at the same time moved the original HDD to the optical drive bay. I'm running the OS and most of my daily apps off the SDD so the HDD is really just for storing stuff I need now and then. Now I'd like to disable (as in power off or "force sleep") the HDD when I don't need it. Tried unmounting the disk using diskutil unmountDisk but it kept spinning for like 10 minutes. Maybe that's to be expected, but I'd imagined it would stop instantly on unmount. Also, it would be nice to have it disabled by default, and only mount it (= power on) when I need it. Grateful for any input on this!

    Read the article

  • HDD bad sectors with OS

    - by Michael Z
    I wonder is that possible for OS to make bad sectors on Hard Drive? Preface: I have bought new HDD on 1Tb WB Caviar Black. I have installed new OS on ext4 partition Ubuntu 12.04.1 LTS. After few days S.M.A.R.T. of the Ubuntu's Disk Utility show that my hard has bad sectors! I have checked on S.M.A.R.T. immediately after installing OS - all was OK. During new OS working I have noticed some strange with HDD - all OS was freezed from 20 sec to 1 min and I have heard like HDD's engine restarting. At the dmes I have found something like this: [40085.407947] ata1.00: device reported invalid CHS sector 0

    Read the article

  • My WD Caviar Green SATA HDD cannot be detected

    - by obhasha
    I have a WD 2TB Caviar Green SATA HDD. I used it as an external hard drive formatted to FAT32. The main purpose was to store my PS3 games. It worked fine and all of a sudden my PS3 stopped detecting it. I tried connecting it to my pc and the same result. I took it off from the enclosure and plugged it directly to my PC and used the BIOS setup. The BIOS setup detects my HDD but it says it's 0.0MB!!! I also tried the WD Data Lifeguard Diagnostic tool and it wasn't much of use because the drive is not picking up by windows at all. Is my HDD dead? Is it beyond repair?

    Read the article

  • If I partition a drive connected via eSata will it show different partitions when connected via USB?

    - by jeffreypriebe
    I have an odd problem with an external drive. I'm formatting it connected to my laptop prior to connecting it to my router. The HDD enclosure has both an eSata and USB connections. Generally, I connect it via eSata to my laptop. I created my partitions and connected it to the router, but I see partition information that is different than what I created. After chasing leads concerning large HDD size, I mindlessly connected the HDD to my laptop with USB. Lo! I see the same partitions as the router. Attached are screenshots using the same program and the HDD in question. The only difference is the connection. For the first, I connected via eSata and hit "refresh" on the partition program. Then, turned off the HDD, disconnected the eSata cable, and connected via USB. Power and refresh. eSata: reports a total HDD size of 2328 GB, with four partitions (the third being 1.96TB) USB: reports a total HDD size of 280 GB, with three partitions (the third being 279 GB) Any idea why this is happening? It looks like it clearly is an issue of the 4K sector size and not playing nice with the USB enclosure. I tried it eSata and USB in Windows and Linux and it appears consistently that eSata is reporting correctly, USB incorrectly.

    Read the article

  • Can I clone my hard drive to an external and boot from the clone?

    - by willbuntu
    First thing: I am not asking what software I'm supposed to use. I already know the answer: Ghost (proprietary), Clonezilla, and dd (if I'm careful). What I really want to know is if it is possible to (essentially) bit-for-bit clone my entire installation (OS, installed software, activation(s), etc.) to an external USB hard-drive, and then boot off of that (if I need to, I know how to edit BIOS settings and use Plop boot manager), and work with it day-to-day as if there was virtually no difference from using my internal HDD now. Again, I'm not asking how to install Windows to an external (because I know I'd need to do some special workaround), I'm asking if I can clone everything and boot off of it. In case you're wondering why I'm going to this trouble: I'm using a Lenovo Essentials laptop that has an unmodifiable partition table (due to recovery crap), and has all 4 of its partitions spoken for (3 primary, one extended, cannot change the extended). Anyway, my thought is that if I can clone everything and boot off of it when I need to, and just have a Linux distro on the internal HDD, then that could work.

    Read the article

  • My Folders Become Hidden System Files And Access Denied?

    - by echolab
    I just aske a question in Superuser site , i have an external hdd which suddenly seems infected and one of my folders which contain my photos changed to something like this One of superuser guys suggest that i install an ubuntu and try to scan and change permissions , but i am not an ubuntu expert , and believe me if my problem solve i will switch to it ( cause all i do is writing and taking photos i am tired of malewares and etc ) Now i have ubuntu and fedora installed ( after a long read through guides ) , both of them show infected folder as empty ( in windows 7 i see this strange folders , you can see in picture )

    Read the article

  • Can&rsquo;t eject external USB or Firewire drive in Windows 7

    - by Kelly Jones
    As a SharePoint developer, I work a lot with Virtual Machines (presently using Windows Virtual PC, with Windows 7).  I’m using these VMs with my laptop, and in order to get better performance, I’ve moved them to external hard drives.  (These drives have faster RPMs, larger caches, and a larger capacity, than the internal drive.)  I have one large external drive at home, another similar drive at the office, and a small, slow portable drive that I carry with me. So, at the end of each day at the office, I copy the files from the external drive to my portable drive and then once I get home, I copy them from the portable to the larger external drive I leave at home.  I do this for a couple of reasons: so I can work at home and secondly, so I have backup copies.  (Often, I feel like I’m in the movie “Office Space” when copying the files before I leave the office). Anyway, after the files are copied, I safely eject the external drives, and then hibernate my laptop.  I’ve been doing this for over a year now, but within the last couple of months I started to have issues disconnecting the drives.  Intermittently, some application/process would have a lock on some file on the drive that would keep Windows from safely ejecting it. After looking into it, I found that it was actually the Windows search service that was accessing the drive! Since I wasn’t using Windows search to look for stuff on these drives, I removed them as locations to index. To do this in Windows 7, you need to go to Indexing Options (just type “Indexing” into the search box in the Start menu…).  One of the choices displayed will then be Indexing Options, so click on it and you should then see a window similar to this:   Click on the Modify button and you’ll see this window: Notice the different drives listed above.  My “FreeAgent XTreme (F:)” drive was checked for some reason, which was causing the indexing service to scan the drive looking for new files to make available in the search results.  Ever since I unchecked this box, I’ve been able to safely eject the drive.

    Read the article

  • Windows Server 2008 - one MAC Address, assign multiple external IP's to VirtualBoxes running as guests on host

    - by Sise
    Couldn't find any help @ google or here. The scenario: Windows Server 2008 Std x64 on i7-975, 12 GB RAM. The server is running in a data centre. One hardware NIC - RealTek PCIe GBE - one MAC Address. The data centre provides us 4 static external IP's. The first is assigned to the host by default of course. I have ordered all 4 IP's, the data centre can assign the available IP's to the physical MAC address of the given NIC only. This means one NIC, one MAC Address, 4 IP's. Everything works fine so far. Now, what I would like to have: Installed VirtualBox with 1-3 guests running, each gets it's own external IP assigned. Each of it should be an standalone Win Server 2008. It looks like the easiest way would be to put the guests into an virtual subnet and routing all data coming to the 2nd till 4th external IP through to this guests using there subnet IP's. I have been through the VirtualBox User Manuel regarding networking. What's not working: I can't use bridged networking without anything else, because the IP's are assigned to the one MAC address only. I can't use NAT networking because it does not allow access from outside or the host to the guest. I do not wanna use port forwarding. Host-only networking itself would not allow internet access, by sharing the default internet connection of the host, internet is granted from the guest to the outside but not from outside or the host to the guest. InternalNetworking is not really an option here. What I have tried is to create an additional MS Loopback adapter for a routed subnet, where the Vbox guests are in, now the idea was to NAT the internet connection to the loopback 'subnet'. But I can't ping the gateway from the guests. By using route command in the command shell or RRAS (static route, NAT) I didn't get there as well. Solutions like the following do work for the one way, but not for the way back: For your situation, it might be best to use the Host-Only adapter for ICS. Go to the preferences of VB itself and select network. There you can change the configuration for the interface. Set the IP address to 192.168.0.1, netmask 255.255.255.0. Disable the DHCP server if it isn't already and that's it. Now the Guest should get an IP from Windows itself and be able to get onto the internet, while you can also access the Host. Slowly I'm pretty stucked with this topic. There is a possibility I've just overlooked something or just didn't getting it by trying, especially using RRAS, but it's kinda hard to find useful howto's or something in the web. Thanks in advance! Best regards, Simon

    Read the article

  • How can I tell a fresh ubuntu 9.0.4 install to boot from an external Mac OS X usb drive?

    - by Richard Dyce
    I have a reformatted Mac mini containing only a fresh install of Ubuntu 9.0.4. The Apple boot loader as been removed, so I can't hold down option, or the c key to get it to reboot form the install DVD. I do have an external drive (with both a usb and firewire interface available) with a bootable cloned OS X system on it. What steps do I need to go through to in order get grub to see the external drive, and to boot from it so that I can reformat the internal disk as an OS X drive?

    Read the article

  • [MINI HOW-TO] Repair Missing External Hard Drive Database Error in WHS

    - by Mysticgeek
    If you’re using external hard drives with your Windows Home Server, they might get unplugged and create an error. Here we look at running the Repair Wizard to quickly fix the issue. If an external drive that is included in your drive pool becomes unplugged or loses power, you might see the following error under Home Network Health when opening the WHS Console. To fix the issue verify the drive has power and is plugged in correctly and click Repair. The wizard launches and you’ll need to agree that you may lose data during the repair of the backup database. In this example it was a simple problem where an external drive became unplugged from the server…so you can close out of the wizard. If you look under Server Storage you can see the drive is missing…To fix the issue verify the drive has power and is plugged in correctly. WHS will add the drive back into the pool and when finished you’ll see it listed as healthy and good to go. Using external drives that are part of your storage pool may not be the best way to have your home built WHS setup, but if you do, expect occasional errors such as this. Similar Articles Productive Geek Tips Find Your Missing USB Drive on Windows XPFixing "BOOTMGR is missing" Error While Trying to Boot Windows VistaSpeed up External USB Hard Drives in Windows VistaRebit Backup Software [Review]Troubleshoot Startup Problems with Startup Repair Tool in Windows 7 & Vista TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips HippoRemote Pro 2.2 Xobni Plus for Outlook All My Movies 5.9 CloudBerry Online Backup 1.5 for Windows Home Server Know if Someone Accessed Your Facebook Account Shop for Music with Windows Media Player 12 Access Free Documentaries at BBC Documentaries Rent Cameras In Bulk At CameraRenter Download Songs From MySpace Steve Jobs’ iPhone 4 Keynote Video

    Read the article

  • changing the default program when external harddisk is plugged in

    - by bharath
    I have updated to ubuntu 11.10. The problem is when I plug in my external harddisk,all the files are trying to get opened with movie player. Also when I click the icon of external harddisk which shows up automatically when we plug in external harddisk in the right side panel, movie player opens up and try to open the files in it. How can I change this default opening program from movie player to file browser. Thanks in earlier.

    Read the article

  • Windows move to external monitor when closing lid

    - by Martijn
    I'm using Cinnamon (on 12.10) on a laptop (Compaq 6710b business model) with an external monitor. Both screens run at 1680 x 1050, the external monitor is located on the right. During normal operation everything works fine; windows open in whatever monitor my mouse pointer is when they open and I can freely drag them to the other monitor. When I close the lid of my laptop both displays shut down as expected. When I open the lid, however, the lock window opens on the external monitor and any windows that were open on the laptop screen have moved to the external monitor as well. Nothing happens between closing the lid and opening it; no suspend, powerdown, hibernate or anything, monitor stays attached; even mouse is untouched (pointer on laptop screen). Is there any way to fix it so my windows stay on whatever monitor I left them before closing the lid? Alternative solutions are welcome.

    Read the article

  • Install Ubuntu or Kubuntu on a External USB Drive

    - by rihatum
    Hi All, I have a few external hard drives (SSDs and Platters (SATA), is this possible that I can install Kubuntu 10.10 x64 or Ubuntu 10.10 x64 onto one of these external hard drives? My System supports booting off a usb, it will just give me a learning playground without spoiling my existing operating environment. I know I can install as Virtual machines, but installing U/Kubuntu on a External HDD and booting off it would be easier. Will be grateful for your insights....and steps to do so. Thanks

    Read the article

  • Can't display at full resolution on an external monitor from my MacBook.

    - by Ramblingwood
    I have a 24" Asus V246H and a new MacBook ($999 one). I am trying to display to display to my Asus at 1080p via VGA. So I boot up with the lid closed and the external monitor plugged in. Everything boots up fine, but the resolution is really low. So I go in and change the resolution to be 1920x1080. My monitor then has a blue box on it that says "OUT OF RANGE". Lower resolutions like 1024x768 work, but 1680x1050 doesn't. If I try mirroring my displays, the entire external monitor AND the entire laptop screen is completely garbled. I can make out some colors, but it is completely unusable. I am suspecting that it simply won't work via VGA, but I don't want to buy another adapter, and my PC is using the DVI port. Any solutions?

    Read the article

  • Windows Server 2008 - one MAC Address, assign multiple external IP's to VirtualBoxes running as guests on host

    - by Sise
    Couldn't find any help @ google or here. The scenario: Windows Server 2008 Std x64 on i7-975, 12 GB RAM. The server is running in a data centre. One hardware NIC - RealTek PCIe GBE - one MAC Address. The data centre provides us 4 static external IP's. The first is assigned to the host by default of course. I have ordered all 4 IP's, the data centre can assign the available IP's to the physical MAC address of the given NIC only. This means one NIC, one MAC Address, 4 IP's. Everything works fine so far. Now, what I would like to have: Installed VirtualBox with 1-3 guests running, each gets it's own external IP assigned. Each of it should be an standalone Win Server 2008. It looks like the easiest way would be to put the guests into an virtual subnet and routing all data coming to the 2nd till 4th external IP through to this guests using there subnet IP's. I have been through the VirtualBox User Manuel regarding networking. What's not working: I can't use bridged networking without anything else, because the IP's are assigned to the one MAC address only. I can't use NAT networking because it does not allow access from outside or the host to the guest. I do not wanna use port forwarding. Host-only networking itself would not allow internet access, by sharing the default internet connection of the host, internet is granted from the guest to the outside but not from outside or the host to the guest. InternalNetworking is not really an option here. What I have tried is to create an additional MS Loopback adapter for a routed subnet, where the Vbox guests are in, now the idea was to NAT the internet connection to the loopback 'subnet'. But I can't ping the gateway from the guests. By using route command in the command shell or RRAS (static route, NAT) I didn't get there as well. Solutions like the following do work for the one way, but not for the way back: For your situation, it might be best to use the Host-Only adapter for ICS. Go to the preferences of VB itself and select network. There you can change the configuration for the interface. Set the IP address to 192.168.0.1, netmask 255.255.255.0. Disable the DHCP server if it isn't already and that's it. Now the Guest should get an IP from Windows itself and be able to get onto the internet, while you can also access the Host. Slowly I'm pretty stucked with this topic. There is a possibility I've just overlooked something or just didn't getting it by trying, especially using RRAS, but it's kinda hard to find useful howto's or something in the web. Thanks in advance! Best regards, Simon

    Read the article

< Previous Page | 15 16 17 18 19 20 21 22 23 24 25 26  | Next Page >