Search Results

Search found 4860 results on 195 pages for 'sudo petruza'.

Page 190/195 | < Previous Page | 186 187 188 189 190 191 192 193 194 195  | Next Page >

  • Nginx + Nagios : 502 Bad gateway

    - by MrROY
    I have a fully new install nagios, but I can't access to it. Here's my Nginx config: server{ listen 80; server_name 61.148.45.10; # blahblah # Nagios Monitoring location /nagios3/ { proxy_pass http://127.0.0.1:80; } } Nagios is installed step by step(From this Linode guide): sudo apt-get install -y nagios3 Then I try to visit http://ip-address/nagios3/, but it shows 502 bad gateway. How do I deal with this ? This is my /var/log/syslog: Oct 25 14:18:17 my-server nagios3: SERVICE ALERT: localhost;Disk Space;WARNING;SOFT;1;DISK WARNING - free space: /boot 43 MB (20% inode=99%): Oct 25 14:19:07 my-server nagios3: SERVICE ALERT: localhost;HTTP;WARNING;SOFT;1;HTTP WARNING: HTTP/1.1 403 Forbidden - 319 bytes in 0.000 second response time Oct 25 14:19:17 my-server nagios3: SERVICE ALERT: localhost;Disk Space;WARNING;SOFT;2;DISK WARNING - free space: /boot 43 MB (20% inode=99%): Oct 25 14:20:07 my-server nagios3: SERVICE ALERT: localhost;HTTP;WARNING;SOFT;2;HTTP WARNING: HTTP/1.1 403 Forbidden - 319 bytes in 0.000 second response time Oct 25 14:20:17 my-server nagios3: SERVICE ALERT: localhost;Disk Space;WARNING;SOFT;3;DISK WARNING - free space: /boot 43 MB (20% inode=99%): Oct 25 14:21:07 my-server nagios3: SERVICE ALERT: localhost;HTTP;WARNING;SOFT;3;HTTP WARNING: HTTP/1.1 403 Forbidden - 319 bytes in 0.000 second response time Oct 25 14:21:17 my-server nagios3: SERVICE ALERT: localhost;Disk Space;WARNING;HARD;4;DISK WARNING - free space: /boot 43 MB (20% inode=99%): Oct 25 14:21:17 my-server nagios3: SERVICE NOTIFICATION: root;localhost;Disk Space;WARNING;notify-service-by-email;DISK WARNING - free space: /boot 43 MB (20% inode=99%): Oct 25 14:21:17 my-server postfix/pickup[24474]: 4F89F394034C: uid=109 from=<nagios> Oct 25 14:21:17 my-server postfix/cleanup[27756]: 4F89F394034C: message-id=<20131025062117.4F89F394034C@my-server> Oct 25 14:21:17 my-server postfix/qmgr[24475]: 4F89F394034C: from=<nagios@[email protected]>, size=594, nrcpt=1 (queue active) Oct 25 14:21:17 my-server postfix/local[27758]: 4F89F394034C: to=<root@localhost>, relay=local, delay=0.15, delays=0.11/0/0/0.04, dsn=2.0.0, status=sent (delivered to mailbox) Oct 25 14:21:17 my-server postfix/qmgr[24475]: 4F89F394034C: removed Oct 25 14:22:07 my-server nagios3: SERVICE ALERT: localhost;HTTP;WARNING;HARD;4;HTTP WARNING: HTTP/1.1 403 Forbidden - 319 bytes in 0.000 second response time Oct 25 14:22:07 my-server nagios3: SERVICE NOTIFICATION: root;localhost;HTTP;WARNING;notify-service-by-email;HTTP WARNING: HTTP/1.1 403 Forbidden - 319 bytes in 0.000 second response time Oct 25 14:22:07 my-server postfix/pickup[24474]: 219CA3940381: uid=109 from=<nagios> Oct 25 14:22:07 my-server postfix/cleanup[27756]: 219CA3940381: message-id=<20131025062207.219CA3940381@my-server> Oct 25 14:22:07 my-server postfix/qmgr[24475]: 219CA3940381: from=<nagios@[email protected]>, size=605, nrcpt=1 (queue active) Oct 25 14:22:07 my-server postfix/local[27758]: 219CA3940381: to=<root@localhost>, relay=local, delay=0.12, delays=0.07/0/0/0.05, dsn=2.0.0, status=sent (delivered to mailbox) Oct 25 14:22:07 my-server postfix/qmgr[24475]: 219CA3940381: removed Oct 25 14:39:01 my-server CRON[28242]: (root) CMD ( [ -x /usr/lib/php5/maxlifetime ] && [ -d /var/lib/php5 ] && find /var/lib/php5/ -depth -mindepth 1 -maxdepth 1 -type f -cmin +$(/usr/lib/php5/maxlifetime) ! -execdir fuser -s {} 2>/dev/null \; -delete) And there're lot of 127.0.0.1 visit in nginx log, but I actually visit from a external ip: 127.0.0.1 - - [25/Oct/2013:14:21:02 +0800] "GET /nagios3/ HTTP/1.0" 502 575 "-" "Mozilla/5.0 (Macintosh; Intel Mac OS X 10_8_5) AppleWebKit/537.36 (KHTML, like Gecko) Chrome/3 0.0.1599.69 Safari/537.36" 127.0.0.1 - - [25/Oct/2013:14:21:02 +0800] "GET /nagios3/ HTTP/1.0" 502 575 "-" "Mozilla/5.0 (Macintosh; Intel Mac OS X 10_8_5) AppleWebKit/537.36 (KHTML, like Gecko) Chrome/3 0.0.1599.69 Safari/537.36" 127.0.0.1 - - [25/Oct/2013:14:21:02 +0800] "GET /nagios3/ HTTP/1.0" 502 575 "-" "Mozilla/5.0 (Macintosh; Intel Mac OS X 10_8_5) AppleWebKit/537.36 (KHTML, like Gecko) Chrome/3 0.0.1599.69 Safari/537.36"

    Read the article

  • Unable to setup postgres on ubuntu (8.4 on 9.10)

    - by shabda
    I am trying to setup postgres on ubuntu, and I cant proceed as I cant find the location of pg_hba.conf (Postgres 8.4 on ubuntu 9.10) What I did setup postgres via aptitude This gave me ... /usr/share/postgresql/8.4# aptitude install postgresql Reading package lists... Done Building dependency tree Reading state information... Done Reading extended state information Initializing package states... Done The following NEW packages will be installed: libreadline5{a} postgresql postgresql-8.4{a} postgresql-client-8.4{a} postgresql-client-common{a} postgresql-common{a} 0 packages upgraded, 6 newly installed, 0 to remove and 0 not upgraded. Need to get 0B/5,159kB of archives. After unpacking 18.8MB will be used. Do you want to continue? [Y/n/?] Y Writing extended state information... Done Preconfiguring packages ... Selecting previously deselected package libreadline5. (Reading database ... 17490 files and directories currently installed.) Unpacking libreadline5 (from .../libreadline5_5.2-6_amd64.deb) ... Selecting previously deselected package postgresql-client-common. Unpacking postgresql-client-common (from .../postgresql-client-common_101_all.deb) ... Selecting previously deselected package postgresql-client-8.4. Unpacking postgresql-client-8.4 (from .../postgresql-client-8.4_8.4.1-1_amd64.deb) ... Selecting previously deselected package postgresql-common. Unpacking postgresql-common (from .../postgresql-common_101_all.deb) ... Selecting previously deselected package postgresql-8.4. Unpacking postgresql-8.4 (from .../postgresql-8.4_8.4.1-1_amd64.deb) ... Selecting previously deselected package postgresql. Unpacking postgresql (from .../postgresql_8.4.1-1_all.deb) ... Processing triggers for man-db ... Setting up libreadline5 (5.2-6) ... Setting up postgresql-client-common (101) ... Setting up postgresql-client-8.4 (8.4.1-1) ... update-alternatives: using /usr/share/postgresql/8.4/man/man1/psql.1.gz to provide /usr/share/man/man1/psql.1.gz (psql.1.gz) in auto mode. Setting up postgresql-common (101) ... Setting up postgresql-8.4 (8.4.1-1) ... update-alternatives: using /usr/share/postgresql/8.4/man/man1/postmaster.1.gz to provide /usr/share/man/man1/postmaster.1.gz (postmaster.1.gz) in auto mode. Setting up postgresql (8.4.1-1) ... Processing triggers for libc-bin ... ldconfig deferred processing now taking place Reading package lists... Done Building dependency tree Reading state information... Done Reading extended state information Initializing package states... Done Writing extended state information... Done tried to login as su - postgres Followed by createdb mytestdb This failed with could not connect to database postgres: could not connect to server: No such file or directory Is the server running locally and accepting connections on Unix domain socket "/var/run/postgresql/.s.PGSQL.5432"? So I though I need to enable local connections in pg_hba.conf, which I cant find. So I created a new file as sudo vim /etc/postgresql/8.4/main/pg_hba.conf With values local all all ident But I still cant login after restarting the service. What are next steps for me to take.

    Read the article

  • Yet another (13)Permission denied error on Apache2 server

    - by lollercoaster
    I just can't figure it out. I'm running apache2 on a Ubuntu 10.04 i386 server. Whenever I visit my server (has an IP address, and is connected to internet with static IP xxx.xxx.xxx.xxx) so that's not the problem) in browser, mysub.domain.edu (renamed here), I get the following: Forbidden You don't have permission to access /index.html on this server The apache2 error log confirms this: [Mon Apr 18 02:38:20 2011] [error] [client zzz.zzz.zzz.zzz] (13)Permission denied: access to / denied I'll try to provide all necessary information below: 1) Contents of /etc/apache2/httpd.conf DirectoryIndex index.html index.php 2) Contents of /etc/apache2/sites-available/default <VirtualHost *:80> ServerAdmin [email protected] DocumentRoot /home/myusername/htdocs <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory "/home/myusername/htdocs/"> Options Indexes FollowSymLinks MultiViews AllowOverride None order allow,deny allow from all DirectoryIndex index.html index.php Satisfy any </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> ServerName mysub.domain.edu </VirtualHost> 3) Contents of /etc/apache2/sites-enabled/000-default <VirtualHost *:80> ServerAdmin [email protected] DocumentRoot /home/myusername/htdocs <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory "/home/myusername/htdocs/"> Options Indexes FollowSymLinks MultiViews AllowOverride None order allow,deny allow from all DirectoryIndex index.html index.php Satisfy any </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> ServerName mysub.domain.edu </VirtualHost> 4) Result of ls -l (when I'm using sudo -i to be root): root@myserver:/home/myusername# ls -l total 4 drwxr-xr-x 2 www-data root 4096 2011-04-18 03:04 htdocs 5) ps auxwww | grep -i apache root@myserver:/home# ps auxwww | grep -i apache root 15121 0.0 0.4 5408 2544 ? Ss 16:55 0:00 /usr/sbin/apache2 -k start www-data 15122 0.0 0.3 5180 1760 ? S 16:55 0:00 /usr/sbin/apache2 -k start www-data 15123 0.0 0.5 227020 2788 ? Sl 16:55 0:00 /usr/sbin/apache2 -k start www-data 15124 0.0 0.5 227020 2864 ? Sl 16:55 0:00 /usr/sbin/apache2 -k start root 29133 0.0 0.1 3320 680 pts/0 R+ 16:58 0:00 grep --color=auto -i apache 6) ls -al /home/myusername/htdocs/ root@myserver:/# ls -al /home/myusername/htdocs/ total 20 drwxr-xr-x 2 www-data root 4096 2011-04-18 03:04 . drw-r--r-- 4 myusername myusername 4096 2011-04-18 02:13 .. -rw-r--r-- 1 root root 69 2011-04-18 02:14 index.html I'm not currently using any .htaccess files in my web root (htdocs) folder in my user folder. I don't know what is wrong, I've been trying to fix his for over 12 hours and I've gotten nowhere. If you have any suggestions, I'm all ears...

    Read the article

  • Persistent static routes fail on MacOS 10.6.5 startup!

    - by verbalicious
    I'm unable to get static routes to persist a reboot on Mac OS 10.6.5. I've tried all of the methods prescribed in Google search results, and previous posts on this site. I've tried manually creating a launchd daemon, and used RouteSplit's launchd daemon to no avail. It's clear that the interface is not ready when these methods attempt to apply the route. This workstation in question is getting its IP from DHCP and probably hasn't gotten its DHCP lease when the command runs. We're able to apply the route by hand when logged in, but not through startup methods. Is there another way to apply this route by sneaking the command into something later, but before the login window appears to the user? Here is some relevant log info from system.log. You can see the "route: writing to routing socket: Network is unreachable" errors where my launchd script fires off. I've tried adding extra "sleep" and "ipconfig waitall" statements later in the script but this doesn't fly. Dec 15 19:30:41 localhost com.apple.launchd[1]: *** launchd[1] has started up. *** Dec 15 19:30:45 localhost mDNSResponder[18]: mDNSResponder mDNSResponder-258.13 (Oct 8 2010 17:10:30) starting Dec 15 19:30:47 localhost configd[15]: bootp_session_transmit: bpf_write(en1) failed: Network is down (50) Dec 15 19:30:47 localhost configd[15]: DHCP en1: INIT transmit failed Dec 15 19:30:47 localhost configd[15]: network configuration changed. Dec 15 19:30:47 Administrators-MacBook-Pro configd[15]: setting hostname to "Administrators-MacBook-Pro.local" Dec 15 19:30:47 Administrators-MacBook-Pro blued[16]: Apple Bluetooth daemon started Dec 15 19:30:52 Administrators-MacBook-Pro syslog[67]: routes.sh: Starting RouteSplit Dec 15 19:30:53 Administrators-MacBook-Pro com.apple.usbmuxd[41]: usbmuxd-207 built for iTunesTenOne on Oct 19 2010 at 13:50:35, running 64 bit Dec 15 19:30:54 Administrators-MacBook-Pro /System/Library/CoreServices/loginwindow.app/Contents/MacOS/loginwindow[50]: Login Window Application Started Dec 15 19:30:55 Administrators-MacBook-Pro bootlog[61]: BOOT_TIME: 1292459441 0 Dec 15 19:30:55 Administrators-MacBook-Pro syslog[86]: routes.sh: static route 192.168.0.0/23 192.168.2.2 Dec 15 19:30:55 Administrators-MacBook-Pro net.routes.static[65]: route: writing to routing socket: Network is unreachable Dec 15 19:30:55 Administrators-MacBook-Pro net.routes.static[65]: add net 192.168.0.0: gateway 192.168.2.2: Network is unreachable Dec 15 19:30:57 Administrators-MacBook-Pro org.apache.httpd[38]: httpd: Could not reliably determine the server's fully qualified domain name, using Administrators-MacBook-Pro.local for ServerName Dec 15 19:30:58 Administrators-MacBook-Pro loginwindow[50]: Login Window Started Security Agent Dec 15 19:30:58 Administrators-MacBook-Pro WindowServer[89]: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged. Dec 15 19:30:58 Administrators-MacBook-Pro com.apple.WindowServer[89]: Wed Dec 15 19:30:58 Administrators-MacBook-Pro.local WindowServer[89] <Error>: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged. Dec 15 19:31:18 Administrators-MacBook-Pro configd[15]: network configuration changed. Dec 15 19:31:19 administrators-macbook-pro configd[15]: setting hostname to "administrators-macbook-pro.local" Dec 15 19:31:25 administrators-macbook-pro _mdnsresponder[121]: /usr/libexec/ntpd-wrapper: scutil key State:/Network/Global/DNS not present after 30 seconds Dec 15 19:31:25 administrators-macbook-pro _mdnsresponder[124]: sntp options: a=2 v=1 e=0.100 E=5.000 P=2147483647.000 Dec 15 19:31:25 administrators-macbook-pro _mdnsresponder[124]: d=15 c=5 x=0 op=1 l=/var/run/sntp.pid f= time.apple.com Dec 15 19:31:25 administrators-macbook-pro _mdnsresponder[124]: sntp: getaddrinfo(hostname, ntp) failed with nodename nor servname provided, or not known Dec 15 19:31:27 administrators-macbook-pro configd[15]: network configuration changed. Dec 15 19:31:27 Administrators-MacBook-Pro configd[15]: setting hostname to "Administrators-MacBook-Pro.local" Dec 15 19:31:27 Administrators-MacBook-Pro ntpd[37]: Cannot find existing interface for address 17.151.16.20 Dec 15 19:31:27 Administrators-MacBook-Pro ntpd_initres[125]: ntpd indicates no data available! Dec 15 19:31:31 Administrators-MacBook-Pro sshd[128]: USER_PROCESS: 133 ttys000 Dec 15 19:31:37 Administrators-MacBook-Pro sudo[138]: administrator : TTY=ttys000 ; PWD=/Users/administrator ; USER=root ; COMMAND=/usr/bin/less /var/log/system.log ``You can see the following line in /var/log/kernel.log that shows the en0 interface coming up: Dec 15 19:30:51 Administrators-MacBook-Pro kernel[0]: Ethernet [AppleBCM5701Ethernet]: Link up on en0, 1-Gigabit, Full-duplex, No flow-control, Debug [796d,0f01,0de1,0300,c1e1,3800]

    Read the article

  • How to start dovecot?

    - by chudapati09
    I'm building a web server to host multiple websites. I got everything working except the mail server. I'm using linode to host my vps and I've been following their tutorials. FYI, I'm using Ubuntu 11.10. Here is the link I've been following, http://library.linode.com/email/postfix/dovecot-mysql-ubuntu-10.04-lucid. I got up to the part where it tells me to restart dovecot, so I tried "service dovecot restart". But then I get this "restart: Unknown instance:". I'm logged in as root, so I'm not using sudo. Since that didn't work I tried "/etc/init.d/dovecot restart" and I get "dovecot start/running, process 4760". So I try "/etc/init.d/dovecot status" and I get "dovecot stop/waiting". So I tried "service dovecot start" and I get "dovecot start/running, process 4781". So I tried to get the status, so I tired "service dovecot status" and got "dovecot stop/waiting" Then I tired "/etc/init.d/dovecot start" and I get "dovecot start/running, process 4794". So I tired to get the status, so I tired "/etc/init.d/dovecot status" and got "dovecot stop/waiting" Just for kicks and giggles I tired to kill the process, I used the PID that I got when I did "service dovecot start", this was the command "kill -9 4444" and I get this "bash: kill: (4805) - No such process" Am I doing something wrong? --EDIT 1-- The following are logs that were found in /var/log/syslog that involved dovecot dovecot: master: Dovecot v2.0.13 starting up (core dumps disabled) dovecot: ssl-params: Generating SSL parameters dovecot: ssl-params: SSL parameters regeneration completed dovecot: master: Warning: Killed with signal 15 (by pid=1 uid=0 code=kill) dovecot: config: Warning: Killed with signal 15 (by pid=1 uid=0 code=kill) dovecot: anvil: Warning: Killed with signal 15 (by pid=1 uid=0 code=kill) dovecot: log: Warning: Killed with signal 15 (by pid=1 uid=0 code=kill) kernel: init: dovecot main process (10276) terminated with status 89 kernel: init: dovecot main process (10289) terminated with status 89 kernel: init: dovecot main process (10452) terminated with status 89 kernel: init: dovecot main process (2275) terminated with status 89 kernel: init: dovecot main process (3028) terminated with status 89 kernel: init: dovecot main process (3216) terminated with status 89 kernel: init: dovecot main process (3230) terminated with status 89 kernel: init: dovecot main process (3254) terminated with status 89 kernel: init: dovecot main process (3813) terminated with status 89 kernel: init: dovecot main process (3845) terminated with status 89 kernel: init: dovecot main process (4664) terminated with status 89 kernel: init: dovecot main process (4760) terminated with status 89 kernel: init: dovecot main process (4781) terminated with status 89 kernel: init: dovecot main process (4794) terminated with status 89 kernel: init: dovecot main process (4805) terminated with status 89 --Edit 2 (/etc/dovecot/dovecot.conf)-- The following is the dovecot.conf file protocols = imap imaps pop3 pop3s log_timestamp = "%Y-%m-%d %H:%M:%S " mail_location = maildir:/home/vmail/%d/%n/Maildir ssl_cert_file = /etc/ssl/certs/dovecot.pem ssl_key_file = /etc/ssl/private/dovecot.pem namespace private { separator = . prefix = INBOX. inbox = yes } protocol lda { log_path = /home/vmail/dovecot-deliver.log auth_socket_path = /var/run/dovecot/auth-master postmaster_address = postmaster@[mydomainname.com] mail_plugins = sieve global_script_path = /home/vmail/globalsieverc } protocol pop3 { pop3_uidl_format = %08Xu%08Xv } auth default { user = root passdb sql { args = /etc/dovecot/dovecot-sql.conf } userdb static { args = uid=5000 gid=5000 home=/home/vmail/%d/%n allow_all_users=yes } socket listen { master { path = /var/run/dovecot/auth-master mode = 0600 user = vmail } client { path = /var/spool/postfix/private/auth mode = 0660 user = postfix group = postfix } } } -- Edit 3 (/var/log/mail.log) -- The following is what is in /var/log/mail.log dovecot: master: Dovecot v2.0.13 starting up (core dumps disabled) dovecot: ssl-params: Generating SSL parameters postfix/master[9917]: daemon started -- version 2.8.5, configuration /etc/postfix dovecot: ssl-params: SSL parameters regeneration completed postfix/master[9917]: terminating on signal 15 postfix/master[10196]: daemon started -- version 2.8.5, configuration /etc/postfix dovecot: master: Warning: Killed with signal 15 (by pid=1 uid=0 code=kill) dovecot: config: Warning: Killed with signal 15 (by pid=1 uid=0 code=kill) dovecot: anvil: Warning: Killed with signal 15 (by pid=1 uid=0 code=kill) dovecot: log: Warning: Killed with signal 15 (by pid=1 uid=0 code=kill) postfix/master[2435]: daemon started -- version 2.8.5, configuration /etc/postfix postfix/master[2435]: terminating on signal 15 postfix/master[2965]: daemon started -- version 2.8.5, configuration /etc/postfix

    Read the article

  • /etc/rc.local not being run on Ubuntu Desktop Install

    - by loosecannon
    I have been trying to get sphinx to run at boot, so I added some lines to /etc/rc.local but nothing happens when I start up. If i run it manually it works however. /etc/init.d/rc.local start works fine as does /etc/rc.local It's listed in the default runlevel and is all executable but it does not work. I am considering writing a separate init.d script to do the same thing but that's a lot of work for a simple task dumbledore:/etc/init.d# ls -l rc* -rwxr-xr-x 1 root root 8863 2009-09-07 13:58 rc -rwxr-xr-x 1 root root 801 2009-09-07 13:58 rc.local -rwxr-xr-x 1 root root 117 2009-09-07 13:58 rcS dumbledore:/etc/init.d# ls /etc/rc.local -l -rwxr-xr-x 1 root root 491 2011-05-14 16:13 /etc/rc.local dumbledore:/etc/init.d# runlevel N 2 dumbledore:/etc/init.d# ls /etc/rc2.d/ -l total 4 lrwxrwxrwx 1 root root 18 2011-04-22 18:53 K08vmware -> /etc/init.d/vmware -rw-r--r-- 1 root root 677 2011-03-28 15:10 README lrwxrwxrwx 1 root root 18 2011-04-22 18:53 S19vmware -> /etc/init.d/vmware lrwxrwxrwx 1 root root 18 2011-05-15 14:09 S20ddclient -> ../init.d/ddclient lrwxrwxrwx 1 root root 20 2011-03-10 18:00 S20fancontrol -> ../init.d/fancontrol lrwxrwxrwx 1 root root 20 2011-03-10 18:00 S20kerneloops -> ../init.d/kerneloops lrwxrwxrwx 1 root root 27 2011-03-10 18:00 S20speech-dispatcher -> ../init.d/speech-dispatcher lrwxrwxrwx 1 root root 19 2011-03-10 18:00 S25bluetooth -> ../init.d/bluetooth lrwxrwxrwx 1 root root 20 2011-03-10 18:00 S50pulseaudio -> ../init.d/pulseaudio lrwxrwxrwx 1 root root 15 2011-03-10 18:00 S50rsync -> ../init.d/rsync lrwxrwxrwx 1 root root 15 2011-03-10 18:00 S50saned -> ../init.d/saned lrwxrwxrwx 1 root root 19 2011-03-10 18:00 S70dns-clean -> ../init.d/dns-clean lrwxrwxrwx 1 root root 18 2011-03-10 18:00 S70pppd-dns -> ../init.d/pppd-dns lrwxrwxrwx 1 root root 14 2011-05-07 11:22 S75sudo -> ../init.d/sudo lrwxrwxrwx 1 root root 24 2011-03-10 18:00 S90binfmt-support -> ../init.d/binfmt-support lrwxrwxrwx 1 root root 17 2011-05-12 21:18 S91apache2 -> ../init.d/apache2 lrwxrwxrwx 1 root root 22 2011-03-10 18:00 S99acpi-support -> ../init.d/acpi-support lrwxrwxrwx 1 root root 21 2011-03-10 18:00 S99grub-common -> ../init.d/grub-common lrwxrwxrwx 1 root root 18 2011-03-10 18:00 S99ondemand -> ../init.d/ondemand lrwxrwxrwx 1 root root 18 2011-03-10 18:00 S99rc.local -> ../init.d/rc.local dumbledore:/etc/init.d# cat /etc/rc.local #!/bin/sh -e # # rc.local # # This script is executed at the end of each multiuser runlevel. # Make sure that the script will "exit 0" on success or any other # value on error. # # In order to enable or disable this script just change the execution # bits. # # By default this script does nothing. # Start sphinx daemon for rails app on startup # Added 2011-05-13 # Cannon Matthews cd /var/www/extemp /usr/bin/rake ts:config /usr/bin/rake ts:start touch ./tmp/ohyeah cd - exit 0 dumbledore:/etc/init.d# cat /etc/init.d/rc.local #! /bin/sh ### BEGIN INIT INFO # Provides: rc.local # Required-Start: $remote_fs $syslog $all # Required-Stop: # Default-Start: 2 3 4 5 # Default-Stop: # Short-Description: Run /etc/rc.local if it exist ### END INIT INFO PATH=/sbin:/usr/sbin:/bin:/usr/bin . /lib/init/vars.sh . /lib/lsb/init-functions do_start() { if [ -x /etc/rc.local ]; then [ "$VERBOSE" != no ] && log_begin_msg "Running local boot scripts (/etc/rc.local)" /etc/rc.local ES=$? [ "$VERBOSE" != no ] && log_end_msg $ES return $ES fi } case "$1" in start) do_start ;; restart|reload|force-reload) echo "Error: argument '$1' not supported" >&2 exit 3 ;; stop) ;; *) echo "Usage: $0 start|stop" >&2 exit 3 ;; esac

    Read the article

  • cf3 Can't stat ... in files.copyfrom promise

    - by Xerxes
    On the client: # cf-agent -KIv ... cf3 -> Handling file existence constraints on /etc/cfengine3 cf3 -> Copy file /etc/cfengine3 from /srv/cfengine/sysconf/server/inputs check cf3 No existing connection to 172.31.69.83 is established... cf3 Set cfengine port number to 5308 = 5308 cf3 -> Connect to 172.31.69.83 = 172.31.69.83 on port 5308 cf3 LastSaw host 172.31.69.83 now cf3 Loaded /var/lib/cfengine3/ppkeys/root-172.31.69.83.pub cf3 .....................[.h.a.i.l.]................................. cf3 Strong authentication of server=172.31.69.83 connection confirmed cf3 Server returned error: Unspecified server refusal (see verbose server output) cf3 Can't stat /srv/cfengine/sysconf/server/inputs in files.copyfrom promise cf3 ?> defining promise result class Cfengine_Inputs_Updated_Failed .... cf3 ......................................................... cf3 Promise handle: cf3 Promise made by: [cf-agent.cf ] FAILED 172.31.69.83:///srv/cfengine/sysconf/server/inputs -> localhost:///etc/cfengine3 However, on the server (172.31.69.83), there's no reason why it can't stat the directory: cyrus:/srv/cfengine/sysconf/server# ls -l /srv/cfengine/sysconf/server/inputs total 52 -rw-r--r-- 1 root root 2142 Sep 6 21:54 cf-agent.cf -rw-r--r-- 1 root root 831 Sep 6 18:31 cf-execd.cf -rw-r--r-- 1 root root 4517 Sep 6 21:44 cf-serverd.cf -rw-r--r-- 1 root root 3082 Sep 6 21:44 dns.cf -rw-r--r-- 1 root root 2028 Sep 6 15:12 failsafe.cf -rw-r--r-- 1 root root 5966 Sep 6 21:44 ldap-masters.cf -rw-r--r-- 1 root root 4380 Sep 6 18:31 ldap-security.cf -rw-r--r-- 1 root root 2735 Sep 6 08:21 lib-core.cf -rw-r--r-- 1 root root 1506 Sep 6 21:45 lib-utils.cf -rw-r--r-- 1 root root 2635 Sep 6 20:27 lib-vars.cf -rw-r--r-- 1 root root 2057 Sep 3 17:46 nss.cf -rw-r--r-- 1 root root 1472 Sep 6 18:31 packages.cf -rw-r--r-- 1 root root 1257 Sep 6 18:01 pam-security.cf -rw-r--r-- 1 root root 4019 Sep 6 19:32 promises.cf -rw-r--r-- 1 root root 2808 Sep 3 17:22 site.cf -rw-r--r-- 1 root root 1670 Sep 6 18:31 sudo-security.cf -rw-r--r-- 1 root root 831 Sep 6 18:31 sys-security.cf -rw-r--r-- 1 root root 890 Sep 6 18:31 sys-users.cf cyrus:/srv/cfengine/sysconf/server# I don't see anything interesting server side either when running: /usr/sbin/cf-serverd -d4 --verbose --no-fork And the following does not have any complaints: /usr/sbin/cf-promises -v Any ideas? I'm running cfengine3 on debian, v3.0.5+dfsg-1 - and the cf-agent.cf file is as follows: bundle agent Update { files: linux:: "${cf3.path[inputs]}" action => immediate, move_obstructions => "true", depth_search => Recursive, copy_from => MirrorFrom( "${cf3.host[server]}", "${cf3.path[scm-inputs]}", "true", "0400" ), classes => DefineSoftClass("Cfengine_Inputs_Updated") ; "${cf3.path[sbin]}" comment => "Setting cf3 client sbin scripts: ${cf3.path[sbin]}/", action => immediate, depth_search => Recursive, copy_from => MirrorFrom( "${cf3.host[server]}", "${cf3.path[scm-cnt-scripts]}", "false", "0555" ) ; reports: Cfengine_Inputs_Updated:: "[cf-agent.cf ] Services:CFAgent:Inputs:Updated"; Cfengine_Inputs_Updated_Failed:: "[cf-agent.cf ] FAILED ${cf3.host[server]}://${cf3.path[scm-inputs]} -> localhost://${cf3.path[inputs]}"; } I lie, there is something interesting with a little more debugging... AccessControl(/srv/cfengine/sysconf/server/inputs) AccessControl, match(/srv/cfengine/sysconf/server/inputs,client.com.au) encrypt request=1 Examining rule in access list (/srv/cfengine/sysconf/server/inputs,/home/cfengine)? cf3 Host client.com.au denied access to /srv/cfengine/sysconf/server/inputs Unappending Host client.com.au denied access to /srv/cfengine/sysconf/server/inputs cf3 Access control in sync Unappending Access control in sync Transaction Send[t 59][Packed text] Attempting to send 67 bytes SendSocketStream, sent 67 cf3 From (host=client.com.au,user=root,ip=172.31.69.3) Unappending From (host=client.com.au,user=root,ip=172.31.69.3) cf3 REFUSAL of request from connecting host: (SYNCH 1283777156 STAT /srv/cfengine/sysconf/server/inputs) Unappending REFUSAL of request from connecting host: (SYNCH 1283777156 STAT /srv/cfengine/sysconf/server/inputs) RecvSocketStream(8) cf3 -> Accepting a connection I'll keep looking.

    Read the article

  • Permissions restoring from Time Machine - Finder copy vs "cp" copy

    - by Ben Challenor
    Note: this question was starting to sprawl so I rewrote it. I have a folder that I'm trying to restore from a Time Machine backup. Using cp -R works fine, but certain folders cannot be restored with either the Time Machine UI or Finder. Other users have reported similar errors and the cp -R workaround was suggested (e.g. Restoring from Time Machine - Permissions Error). But I wanted to understand: Why cp -R works when the Finder and the Time Machine UI do not. Whether I could prevent the errors by changing file permissions before the backup. There do indeed seem to be some permissions that Finder works with and some that it does not. I've narrowed the errors down to folders with the user ben (that's me) and the group wheel. Here's a simplified reproduction. I have four folders with the owner/group combinations I've seen so far: ben ~/Desktop/test $ ls -lea total 16 drwxr-xr-x 7 ben staff 238 27 Nov 14:31 . drwx------+ 17 ben staff 578 27 Nov 14:29 .. 0: group:everyone deny delete -rw-r--r--@ 1 ben staff 6148 27 Nov 14:31 .DS_Store drwxr-xr-x 3 ben staff 102 27 Nov 14:30 ben-staff drwxr-xr-x 3 ben wheel 102 27 Nov 14:30 ben-wheel drwxr-xr-x 3 root admin 102 27 Nov 14:31 root-admin drwxr-xr-x 3 root wheel 102 27 Nov 14:31 root-wheel Each contains a single file called file with the same owner/group: ben ~/Desktop/test $ cd ben-staff ben ~/Desktop/test/ben-staff $ ls -lea total 0 drwxr-xr-x 3 ben staff 102 27 Nov 14:30 . drwxr-xr-x 7 ben staff 238 27 Nov 14:31 .. -rw-r--r-- 1 ben staff 0 27 Nov 14:30 file In the backup, they look like this: ben /Volumes/Deimos/Backups.backupdb/Ben’s MacBook Air/Latest/Macintosh HD/Users/ben/Desktop/test $ ls -leA total 16 -rw-r--r--@ 1 ben staff 6148 27 Nov 14:34 .DS_Store 0: group:everyone deny write,delete,append,writeattr,writeextattr,chown drwxr-xr-x@ 3 ben staff 102 27 Nov 14:51 ben-staff 0: group:everyone deny add_file,delete,add_subdirectory,delete_child,writeattr,writeextattr,chown drwxr-xr-x@ 3 ben wheel 102 27 Nov 14:51 ben-wheel 0: group:everyone deny add_file,delete,add_subdirectory,delete_child,writeattr,writeextattr,chown drwxr-xr-x@ 3 root admin 102 27 Nov 14:52 root-admin 0: group:everyone deny add_file,delete,add_subdirectory,delete_child,writeattr,writeextattr,chown drwxr-xr-x@ 3 root wheel 102 27 Nov 14:52 root-wheel 0: group:everyone deny add_file,delete,add_subdirectory,delete_child,writeattr,writeextattr,chown Of these, ben-staff can be restored with Finder without errors. root-wheel and root-admin ask for my password and then restore without errors. But ben-wheel does not prompt for my password and gives the error: The operation can’t be completed because you don’t have permission to access “file”. Interestingly, I can restore the file from this folder by dragging it directly to my local drive (instead of dragging its parent folder), but when I do so its permissions are changed to ben/staff. Here are the permissions after the restore for the three folders that worked correctly, and the file from ben-wheel that was changed to ben/staff. ben ~/Desktop/test-restore $ ls -leA total 16 -rw-r--r--@ 1 ben staff 6148 27 Nov 14:46 .DS_Store drwxr-xr-x 3 ben staff 102 27 Nov 14:30 ben-staff -rw-r--r-- 1 ben staff 0 27 Nov 14:30 file drwxr-xr-x 3 root admin 102 27 Nov 14:31 root-admin drwxr-xr-x 3 root wheel 102 27 Nov 14:31 root-wheel Can anyone explain this behaviour? Why do Finder and the Time Machine UI break with the ben / wheel permissions? And why does cp -R work (even without sudo)?

    Read the article

  • How to change cpufreq settings in Kubuntu

    - by Mr Woody
    I have been using Kubuntu, and I would like to change the cpufreq settings. My understanding is that there is no applet for that, and I would have to do it with a script. So I run a command like this: sudo cpufreq-set -g userspace -c 0 -d 800Mhz -u 1200Mhz and when I type cpufreq-info, I get cpufrequtils 007: cpufreq-info (C) Dominik Brodowski 2004-2009 Report errors and bugs to [email protected], please. analyzing CPU 0: driver: acpi-cpufreq CPUs which run at the same hardware frequency: 0 1 CPUs which need to have their frequency coordinated by software: 0 maximum transition latency: 10.0 us. hardware limits: 800 MHz - 2.50 GHz available frequency steps: 2.50 GHz, 2.50 GHz, 2.00 GHz, 1.60 GHz, 1.20 GHz, 800 MHz available cpufreq governors: conservative, ondemand, userspace, powersave, performance current policy: frequency should be within 800 MHz and 1.20 GHz. The governor "userspace" may decide which speed to use within this range. current CPU frequency is 1.20 GHz. cpufreq stats: 2.50 GHz:70.06%, 2.50 GHz:0.97%, 2.00 GHz:4.85%, 1.60 GHz:0.35%, 1.20 GHz:2.89%, 800 MHz:20.88% (193873) analyzing CPU 1: driver: acpi-cpufreq CPUs which run at the same hardware frequency: 0 1 CPUs which need to have their frequency coordinated by software: 1 maximum transition latency: 10.0 us. hardware limits: 800 MHz - 2.50 GHz available frequency steps: 2.50 GHz, 2.50 GHz, 2.00 GHz, 1.60 GHz, 1.20 GHz, 800 MHz available cpufreq governors: conservative, ondemand, userspace, powersave, performance current policy: frequency should be within 2.00 GHz and 2.00 GHz. The governor "performance" may decide which speed to use within this range. current CPU frequency is 2.00 GHz. cpufreq stats: 2.50 GHz:83.43%, 2.50 GHz:1.03%, 2.00 GHz:4.28%, 1.60 GHz:0.01%, 1.20 GHz:1.74%, 800 MHz:9.50% (3208) which shows that everything worked well (on cpu 0). The problem is that if I run cpufreq-info again after few minutes I get cpufrequtils 007: cpufreq-info (C) Dominik Brodowski 2004-2009 Report errors and bugs to [email protected], please. analyzing CPU 0: driver: acpi-cpufreq CPUs which run at the same hardware frequency: 0 1 CPUs which need to have their frequency coordinated by software: 0 maximum transition latency: 10.0 us. hardware limits: 800 MHz - 2.50 GHz available frequency steps: 2.50 GHz, 2.50 GHz, 2.00 GHz, 1.60 GHz, 1.20 GHz, 800 MHz available cpufreq governors: conservative, ondemand, userspace, powersave, performance current policy: frequency should be within 800 MHz and 800 MHz. The governor "performance" may decide which speed to use within this range. current CPU frequency is 800 MHz. cpufreq stats: 2.50 GHz:69.73%, 2.50 GHz:0.97%, 2.00 GHz:4.83%, 1.60 GHz:0.35%, 1.20 GHz:2.92%, 800 MHz:21.20% (193880) analyzing CPU 1: driver: acpi-cpufreq CPUs which run at the same hardware frequency: 0 1 CPUs which need to have their frequency coordinated by software: 1 maximum transition latency: 10.0 us. hardware limits: 800 MHz - 2.50 GHz available frequency steps: 2.50 GHz, 2.50 GHz, 2.00 GHz, 1.60 GHz, 1.20 GHz, 800 MHz available cpufreq governors: conservative, ondemand, userspace, powersave, performance current policy: frequency should be within 800 MHz and 800 MHz. The governor "performance" may decide which speed to use within this range. current CPU frequency is 800 MHz. cpufreq stats: 2.50 GHz:82.94%, 2.50 GHz:1.03%, 2.00 GHz:4.33%, 1.60 GHz:0.01%, 1.20 GHz:1.73%, 800 MHz:9.96% (3215) so it looks like some other process changed the settings. Does anyone know how to fix this? I also tried many different settings, but I get similar behavior.

    Read the article

  • Does likewise-open > version 5.4 contain CIFS support?

    - by Ben Andken
    I'm trying to get the CIFS server working in likewise-open. I've found this set of instructions and everything seems to work until I try to connect ([url]http://www.likewise.com/resources/documentation_library/manuals/cifs/likewise-cifs-smb-file-server-guide.html#id2765992):[/url] 1.6. Build and Configure a Standalone Likewise-CIFS Server This section demonstrates how to build and configure a standalone instance of Likewise-CIFS from the command line. The following procedure assumes that you want to set up Likewise-CIFS on a Linux server to share files with Windows computers in a network without Active Directory. This procedure also assumes you know how to build Linux applications from their source code and then install them. Download Likewise-CIFS from its open source git location: $ git clone git://git.likewiseopen.org/ Download, build, and install the following tools. The tools listed are known to work, but earlier or later versions might work as well. Also, instead of downloading the tools, you might be able to install them on your platform with apt-get or some other means. http://ftp.gnu.org/gnu/autoconf/autoconf-2.65.tar.gz http://ftp.gnu.org/gnu/automake/automake-1.9.6.tar.gz http://ftp.gnu.org/gnu/libtool/libtool-2.2.6a.tar.gz http://pkgconfig.freedesktop.org/releases/pkg-config-0.23.tar.gz gcc --version 3.x or greater Build Likewise-CIFS: $ cd likewise-open $ build/mkcomp --debug all Install Likewise-CIFS: $ sudo su $ cd staging/install-root $ tar cf - . | (cd / && tar xvf -) Make sure Samba is not running: $ /etc/init.d/smb stop Make sure SELinux is either disabled or set to permissive. Make sure the ports required by Likewise are open. For a list of ports that Likewise uses, see the Likewise Open Installation and Administration Guide. Configure Likewise Open: $ /etc/init.d/lwsmd start $ for i in /etc/likewise/*.reg; do /opt/likewise/bin/lwregshell upgrade $i; done $ /etc/init.d/lwsmd stop $ /etc/init.d/lwsmd start $ /opt/likewise/bin/lwsm start srvsvc $ /opt/likewise/bin/domainjoin-cli configure --enable nsswitch Add a user account to the local Likewise provider database. In the following example, substitute the account name that you want for newuser. $ /opt/likewise/bin/lw-add-user --home /home/newuser --shell /bin/bash newuser Successfully added user newuser Enable the user and set the password: $ /opt/likewise/bin/lw-mod-user --enable-user --set-password newuser New Password: ********** Successfully modified user newuser Look up new user's identity as follows. Substitute the value from the command hostname -s for the hostname. Keep in mind that Likewise truncates a hostname longer than 15 characters to the first 15 characters of the string. % id hostname\\newuser uid=2000(HOSTNAME\newuser) gid=1800(HOSTNAME\Likewise Users) groups=1800(HOSTNAME\Likewise Users) context=system_u:system_r:unconfined_t:s0 Make a CIFS directory for the user: mkdir /lwcifs/newuser chown 2000:1800 /lwcifs/newuser From a Windows computer, map the Likewise-CIFS drive share: Computer->Map Network Drive... Folder: \\IP_hostname\c$ Click "Finish" Username: hostname\newuser Password: user_password The last step fails when I try to connect. I've tried with Windows XP Pro and Windows 7 Pro. The rest of the directions only appear to work for version 5.4 (the one that shipped with 10.04). For 12.04, version 6.1 is the only one available and it doesn't appear to have the srvsvc module mentioned in these instructions. Is CIFS support dropped in the 6.1 version of likewise-open?

    Read the article

  • Persistent static routes fail on MacOS 10.6.5 startup!

    - by verbalicious
    I'm unable to get static routes to persist a reboot on Mac OS 10.6.5. I've tried all of the methods prescribed in Google search results, and previous posts on this site. I've tried manually creating a launchd daemon, and used RouteSplit's launchd daemon to no avail. It's clear that the interface is not ready when these methods attempt to apply the route. This workstation in question is getting its IP from DHCP and probably hasn't gotten its DHCP lease when the command runs. We're able to apply the route by hand when logged in, but not through startup methods. Is there another way to apply this route by sneaking the command into something later, but before the login window appears to the user? Here is some relevant log info from system.log. You can see the "route: writing to routing socket: Network is unreachable" errors where my launchd script fires off. I've tried adding extra "sleep" and "ipconfig waitall" statements later in the script but this doesn't fly. Dec 15 19:30:41 localhost com.apple.launchd[1]: *** launchd[1] has started up. *** Dec 15 19:30:45 localhost mDNSResponder[18]: mDNSResponder mDNSResponder-258.13 (Oct 8 2010 17:10:30) starting Dec 15 19:30:47 localhost configd[15]: bootp_session_transmit: bpf_write(en1) failed: Network is down (50) Dec 15 19:30:47 localhost configd[15]: DHCP en1: INIT transmit failed Dec 15 19:30:47 localhost configd[15]: network configuration changed. Dec 15 19:30:47 Administrators-MacBook-Pro configd[15]: setting hostname to "Administrators-MacBook-Pro.local" Dec 15 19:30:47 Administrators-MacBook-Pro blued[16]: Apple Bluetooth daemon started Dec 15 19:30:52 Administrators-MacBook-Pro syslog[67]: routes.sh: Starting RouteSplit Dec 15 19:30:53 Administrators-MacBook-Pro com.apple.usbmuxd[41]: usbmuxd-207 built for iTunesTenOne on Oct 19 2010 at 13:50:35, running 64 bit Dec 15 19:30:54 Administrators-MacBook-Pro /System/Library/CoreServices/loginwindow.app/Contents/MacOS/loginwindow[50]: Login Window Application Started Dec 15 19:30:55 Administrators-MacBook-Pro bootlog[61]: BOOT_TIME: 1292459441 0 Dec 15 19:30:55 Administrators-MacBook-Pro syslog[86]: routes.sh: static route 192.168.0.0/23 192.168.2.2 Dec 15 19:30:55 Administrators-MacBook-Pro net.routes.static[65]: route: writing to routing socket: Network is unreachable Dec 15 19:30:55 Administrators-MacBook-Pro net.routes.static[65]: add net 192.168.0.0: gateway 192.168.2.2: Network is unreachable Dec 15 19:30:57 Administrators-MacBook-Pro org.apache.httpd[38]: httpd: Could not reliably determine the server's fully qualified domain name, using Administrators-MacBook-Pro.local for ServerName Dec 15 19:30:58 Administrators-MacBook-Pro loginwindow[50]: Login Window Started Security Agent Dec 15 19:30:58 Administrators-MacBook-Pro WindowServer[89]: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged. Dec 15 19:30:58 Administrators-MacBook-Pro com.apple.WindowServer[89]: Wed Dec 15 19:30:58 Administrators-MacBook-Pro.local WindowServer[89] <Error>: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged. Dec 15 19:31:18 Administrators-MacBook-Pro configd[15]: network configuration changed. Dec 15 19:31:19 administrators-macbook-pro configd[15]: setting hostname to "administrators-macbook-pro.local" Dec 15 19:31:25 administrators-macbook-pro _mdnsresponder[121]: /usr/libexec/ntpd-wrapper: scutil key State:/Network/Global/DNS not present after 30 seconds Dec 15 19:31:25 administrators-macbook-pro _mdnsresponder[124]: sntp options: a=2 v=1 e=0.100 E=5.000 P=2147483647.000 Dec 15 19:31:25 administrators-macbook-pro _mdnsresponder[124]: d=15 c=5 x=0 op=1 l=/var/run/sntp.pid f= time.apple.com Dec 15 19:31:25 administrators-macbook-pro _mdnsresponder[124]: sntp: getaddrinfo(hostname, ntp) failed with nodename nor servname provided, or not known Dec 15 19:31:27 administrators-macbook-pro configd[15]: network configuration changed. Dec 15 19:31:27 Administrators-MacBook-Pro configd[15]: setting hostname to "Administrators-MacBook-Pro.local" Dec 15 19:31:27 Administrators-MacBook-Pro ntpd[37]: Cannot find existing interface for address 17.151.16.20 Dec 15 19:31:27 Administrators-MacBook-Pro ntpd_initres[125]: ntpd indicates no data available! Dec 15 19:31:31 Administrators-MacBook-Pro sshd[128]: USER_PROCESS: 133 ttys000 Dec 15 19:31:37 Administrators-MacBook-Pro sudo[138]: administrator : TTY=ttys000 ; PWD=/Users/administrator ; USER=root ; COMMAND=/usr/bin/less /var/log/system.log ``You can see the following line in /var/log/kernel.log that shows the en0 interface coming up: Dec 15 19:30:51 Administrators-MacBook-Pro kernel[0]: Ethernet [AppleBCM5701Ethernet]: Link up on en0, 1-Gigabit, Full-duplex, No flow-control, Debug [796d,0f01,0de1,0300,c1e1,3800]

    Read the article

  • Nagios: NRPE: Unable to read output, Can't find the reason, can you?

    - by Itai Ganot
    I have a Nagios server and a monitored server. On the monitored server: [root@Monitored ~]# netstat -an |grep :5666 tcp 0 0 0.0.0.0:5666 0.0.0.0:* LISTEN [root@Monitored ~]# locate check_kvm /usr/lib64/nagios/plugins/check_kvm [root@Monitored ~]# /usr/lib64/nagios/plugins/check_kvm -H localhost hosts:3 OK:3 WARN:0 CRIT:0 - ab2c7:running alpweb5:running istaweb5:running [root@Monitored ~]# /usr/lib64/nagios/plugins/check_nrpe -H localhost -c check_kvm NRPE: Unable to read output [root@Monitored ~]# /usr/lib64/nagios/plugins/check_nrpe -H localhost NRPE v2.14 [root@Monitored ~]# ps -ef |grep nrpe nagios 21178 1 0 16:11 ? 00:00:00 /usr/sbin/nrpe -c /etc/nagios/nrpe.cfg -d [root@Monitored ~]# On the Nagios server: [root@Nagios ~]# /usr/lib64/nagios/plugins/check_nrpe -H 1.1.1.159 -c check_kvm NRPE: Unable to read output [root@Nagios ~]# /usr/lib64/nagios/plugins/check_nrpe -H 1.1.1.159 NRPE v2.14 [root@Nagios ~]# When I check another server in the network using the same command it works: [root@Nagios ~]# /usr/lib64/nagios/plugins/check_nrpe -H 1.1.1.80 -c check_kvm hosts:4 OK:4 WARN:0 CRIT:0 - karmisoft:running ab2c4:running kidumim1:running travel2gether1:running [root@Nagios ~]# Running the check locally using Nagios account: [root@Monitored ~]# su - nagios -bash-4.1$ /usr/lib64/nagios/plugins/check_kvm hosts:3 OK:3 WARN:0 CRIT:0 - ab2c7:running alpweb5:running istaweb5:running -bash-4.1$ Running the check remotely from the Nagios server using Nagios account: -bash-4.1$ /usr/lib64/nagios/plugins/check_nrpe -H 1.1.1.159 -c check_kvm NRPE: Unable to read output -bash-4.1$ /usr/lib64/nagios/plugins/check_nrpe -H 1.1.1.159 NRPE v2.14 -bash-4.1$ Running the same check_kvm against a different server in the network using Nagios account: -bash-4.1$ /usr/lib64/nagios/plugins/check_nrpe -H 1.1.1.80 -c check_kvm hosts:4 OK:4 WARN:0 CRIT:0 - karmisoft:running ab2c4:running kidumim1:running travel2gether1:running -bash-4.1$ Permissions: -rwxr-xr-x. 1 root root 4684 2013-10-14 17:14 nrpe.cfg (aka /etc/nagios/nrpe.cfg) drwxrwxr-x. 3 nagios nagios 4096 2013-10-15 03:38 plugins (aka /usr/lib64/nagios/plugins) /etc/sudoers: [root@Monitored ~]# grep -i requiretty /etc/sudoers #Defaults requiretty iptables/selinux: [root@Monitored xinetd.d]# service iptables status iptables: Firewall is not running. [root@Monitored xinetd.d]# service ip6tables status ip6tables: Firewall is not running. [root@Monitored xinetd.d]# grep disable /etc/selinux/config # disabled - No SELinux policy is loaded. SELINUX=disabled [root@Monitored xinetd.d]# The command in /etc/nagios/nrpe.cfg is: [root@Monitored ~]# grep kvm /etc/nagios/nrpe.cfg command[check_kvm]=sudo /usr/lib64/nagios/plugins/check_kvm and the nagios user is added on /etc/sudoers: nagios ALL=(ALL) NOPASSWD:/usr/lib64/nagios/plugins/check_kvm nagios ALL=(ALL) NOPASSWD:/usr/lib64/nagios/plugins/check_nrpe The check_kvm is a shell script, looks like that: #!/bin/sh LIST=$(virsh list --all | sed '1,2d' | sed '/^$/d'| awk '{print $2":"$3}') if [ ! "$LIST" ]; then EXITVAL=3 #Status 3 = UNKNOWN (orange) echo "Unknown guests" exit $EXITVAL fi OK=0 WARN=0 CRIT=0 NUM=0 for host in $(echo $LIST) do name=$(echo $host | awk -F: '{print $1}') state=$(echo $host | awk -F: '{print $2}') NUM=$(expr $NUM + 1) case "$state" in running|blocked) OK=$(expr $OK + 1) ;; paused) WARN=$(expr $WARN + 1) ;; shutdown|shut*|crashed) CRIT=$(expr $CRIT + 1) ;; *) CRIT=$(expr $CRIT + 1) ;; esac done if [ "$NUM" -eq "$OK" ]; then EXITVAL=0 #Status 0 = OK (green) fi if [ "$WARN" -gt 0 ]; then EXITVAL=1 #Status 1 = WARNING (yellow) fi if [ "$CRIT" -gt 0 ]; then EXITVAL=2 #Status 2 = CRITICAL (red) fi echo hosts:$NUM OK:$OK WARN:$WARN CRIT:$CRIT - $LIST exit $EXITVAL Edit (10/22/13): Following all that, I am now able to get some response from the script: [root@Monitored ~]# /usr/lib64/nagios/plugins/check_nrpe -H localhost -c check_kvm Unknown guests [root@Monitored ~]# /usr/lib64/nagios/plugins/check_nrpe -H localhost NRPE v2.14 [root@Monitored ~]# /usr/lib64/nagios/plugins/check_kvm hosts:3 OK:3 WARN:0 CRIT:0 - ab2c7:running alpweb5:running istaweb5:running [root@Monitored ~]# su - nagios -bash-4.1$ /usr/lib64/nagios/plugins/check_kvm hosts:3 OK:3 WARN:0 CRIT:0 - ab2c7:running alpweb5:running istaweb5:running -bash-4.1$ /usr/lib64/nagios/plugins/check_nrpe -H localhost -c check_kvm Unknown guests -bash-4.1$ /usr/lib64/nagios/plugins/check_nrpe -H localhost NRPE v2.14 It seems like the problem is some how related to the check_nrpe command or something which is related to the nrpe installation on the server.

    Read the article

  • Ubuntu: Move fsbackup backups to Amazon S3

    - by Alexander Gladysh
    I have a legacy server (Ubuntu 9.10 Karmic x86), where previous admin set up backups with fsbackup. This server lives in a VPS (under some kind of Xen), and it is low on HDD space (16 GB total). Now it came to a point, where fsbackup backups take more space than the rest of data in the system. The filesystem is 100% filled, and I already cleaned up all that I could, aside from actual backups. I do not have any experience managing fsbackup, and I do not want to break or lose the backups. Googling fsbackup gives surprisingly low quality results... Here is how my backups look like: $ sudo ls -lh /var/archives total 8.1G -rw-rw---- 1 root root 318 2011-01-06 06:26 myserver-20110106.md5 -rw-rw---- 1 root root 258 2011-01-07 06:26 myserver-20110107.md5 -rw-rw---- 1 root root 318 2011-01-08 06:26 myserver-20110108.md5 -rw-rw---- 1 root root 318 2011-01-09 06:26 myserver-20110109.md5 -rw-rw---- 1 root root 346 2011-01-10 06:43 myserver-20110110.md5 -rw-rw---- 1 root root 14M 2011-01-06 06:26 myserver-all-mysql-databases.20110106.sql.bz2 -rw-rw---- 1 root root 14M 2011-01-07 06:26 myserver-all-mysql-databases.20110107.sql.bz2 -rw-rw---- 1 root root 14M 2011-01-08 06:26 myserver-all-mysql-databases.20110108.sql.bz2 -rw-rw---- 1 root root 14M 2011-01-09 06:26 myserver-all-mysql-databases.20110109.sql.bz2 -rw-rw---- 1 root root 862 2011-01-10 06:43 myserver-all-mysql-databases.20110110.sql.bz2 -rw-rw---- 1 root root 827K 2011-01-03 06:25 myserver-etc.20110103.master.tar.gz -rw-rw---- 1 root root 16K 2011-01-06 06:25 myserver-etc.20110106.tar.gz -rw-rw---- 1 root root 16K 2011-01-07 06:25 myserver-etc.20110107.tar.gz -rw-rw---- 1 root root 16K 2011-01-08 06:25 myserver-etc.20110108.tar.gz -rw-rw---- 1 root root 16K 2011-01-09 06:25 myserver-etc.20110109.tar.gz -rw-rw---- 1 root root 827K 2011-01-10 06:25 myserver-etc.20110110.master.tar.gz -rw------- 1 root root 36K 2011-01-10 06:25 myserver-etc.incremental.bin -rw-rw---- 1 root root 29M 2011-01-03 06:25 myserver-home.20110103.master.tar.gz -rw-rw---- 1 root root 11K 2011-01-06 06:25 myserver-home.20110106.tar.gz -rw-rw---- 1 root root 14K 2011-01-07 06:25 myserver-home.20110107.tar.gz -rw-rw---- 1 root root 11K 2011-01-08 06:25 myserver-home.20110108.tar.gz -rw-rw---- 1 root root 11K 2011-01-09 06:25 myserver-home.20110109.tar.gz -rw-rw---- 1 root root 2.0M 2011-01-10 06:25 myserver-home.20110110.master.tar.gz -rw------- 1 root root 27K 2011-01-10 06:25 myserver-home.incremental.bin -rw-rw---- 1 root root 1.5G 2011-01-03 06:29 myserver-opt.20110103.master.tar.gz -rw-rw---- 1 root root 1.5M 2011-01-06 06:25 myserver-opt.20110106.tar.gz -rw-rw---- 1 root root 1.5M 2011-01-07 06:25 myserver-opt.20110107.tar.gz -rw-rw---- 1 root root 1.5M 2011-01-08 06:25 myserver-opt.20110108.tar.gz -rw-rw---- 1 root root 1.5M 2011-01-09 06:25 myserver-opt.20110109.tar.gz -rw-rw---- 1 root root 1.5G 2011-01-10 06:30 myserver-opt.20110110.master.tar.gz -rw------- 1 root root 201K 2011-01-10 06:30 myserver-opt.incremental.bin -rw-rw---- 1 root root 2.3G 2011-01-03 06:41 myserver-srv.20110103.master.tar.gz -rw-rw---- 1 root root 44M 2011-01-06 06:26 myserver-srv.20110106.tar.gz -rw-rw---- 1 root root 27M 2011-01-07 06:25 myserver-srv.20110107.tar.gz -rw-rw---- 1 root root 39M 2011-01-08 06:26 myserver-srv.20110108.tar.gz -rw-rw---- 1 root root 2.0M 2011-01-09 06:25 myserver-srv.20110109.tar.gz -rw-rw---- 1 root root 2.7G 2011-01-10 06:42 myserver-srv.20110110.master.tar.gz -rw------- 1 root root 3.4M 2011-01-10 06:42 myserver-srv.incremental.bin I'm thinking about moving backups to Amazon S3, but before that I have to free some space, so the server can work. Perhaps I can mount /var/archives to an Amazon S3 bucket somehow... Any advice?

    Read the article

  • ERROR 2003 (HY000): Can't connect to MySQL server on (111)

    - by JohnMerlino
    I am unable to connect to on my ubuntu installation a remote tcp/ip which contains a mysql installation: viggy@ubuntu:~$ mysql -u user.name -p -h xxx.xxx.xxx.xxx -P 3306 Enter password: ERROR 2003 (HY000): Can't connect to MySQL server on 'xxx.xxx.xxx.xxx' (111) I commented out the line below using vim in /etc/mysql/my.cnf: # Instead of skip-networking the default is now to listen only on # localhost which is more compatible and is not less secure. #bind-address = 127.0.0.1 Then I restarted the server: sudo service mysql restart But still I get the same error. This is the content of my.cnf: # # The MySQL database server configuration file. # # You can copy this to one of: # - "/etc/mysql/my.cnf" to set global options, # - "~/.my.cnf" to set user-specific options. # # One can use all long options that the program supports. # Run program with --help to get a list of available options and with # --print-defaults to see which it would actually understand and use. # # For explanations see # http://dev.mysql.com/doc/mysql/en/server-system-variables.html # This will be passed to all mysql clients # It has been reported that passwords should be enclosed with ticks/quotes # escpecially if they contain "#" chars... # Remember to edit /etc/mysql/debian.cnf when changing the socket location. [client] port = 3306 socket = /var/run/mysqld/mysqld.sock # Here is entries for some specific programs # The following values assume you have at least 32M ram # This was formally known as [safe_mysqld]. Both versions are currently parsed. [mysqld_safe] socket = /var/run/mysqld/mysqld.sock nice = 0 [mysqld] # # * Basic Settings # user = mysql pid-file = /var/run/mysqld/mysqld.pid socket = /var/run/mysqld/mysqld.sock port = 3306 basedir = /usr datadir = /var/lib/mysql tmpdir = /tmp lc-messages-dir = /usr/share/mysql skip-external-locking # # Instead of skip-networking the default is now to listen only on # localhost which is more compatible and is not less secure. #bind-address = 127.0.0.1 # # * Fine Tuning # key_buffer = 16M max_allowed_packet = 16M thread_stack = 192K thread_cache_size = 8 # This replaces the startup script and checks MyISAM tables if needed # the first time they are touched myisam-recover = BACKUP #max_connections = 100 #table_cache = 64 #thread_concurrency = 10 # # * Query Cache Configuration # query_cache_limit = 1M query_cache_size = 16M # # * Logging and Replication # # Both location gets rotated by the cronjob. # Be aware that this log type is a performance killer. # As of 5.1 you can enable the log at runtime! #general_log_file = /var/log/mysql/mysql.log #general_log = 1 # # Error logging goes to syslog due to /etc/mysql/conf.d/mysqld_safe_syslog.cnf. # # Here you can see queries with especially long duration #log_slow_queries = /var/log/mysql/mysql-slow.log #long_query_time = 2 #log-queries-not-using-indexes # # The following can be used as easy to replay backup logs or for replication. # note: if you are setting up a replication slave, see README.Debian about # other settings you may need to change. #server-id = 1 #log_bin = /var/log/mysql/mysql-bin.log expire_logs_days = 10 max_binlog_size = 100M #binlog_do_db = include_database_name #binlog_ignore_db = include_database_name # # * InnoDB # # InnoDB is enabled by default with a 10MB datafile in /var/lib/mysql/. # Read the manual for more InnoDB related options. There are many! # # * Security Features # # Read the manual, too, if you want chroot! # chroot = /var/lib/mysql/ # # For generating SSL certificates I recommend the OpenSSL GUI "tinyca". # # ssl-ca=/etc/mysql/cacert.pem # ssl-cert=/etc/mysql/server-cert.pem # ssl-key=/etc/mysql/server-key.pem [mysqldump] quick quote-names max_allowed_packet = 16M [mysql] #no-auto-rehash # faster start of mysql but no tab completition [isamchk] key_buffer = 16M # # * IMPORTANT: Additional settings that can override those from this file! # The files must end with '.cnf', otherwise they'll be ignored. # !includedir /etc/mysql/conf.d/ (Note that I can log into my local mysql install just fine by running mysql (and it will log me in as root) and also note that I can get into mysql in the remote server by logging into via ssh and then invoking mysql), but I am unable to connect to the remote server via my terminal using the host, and I need to do it that way so that I can then use mysql workbench.

    Read the article

  • Persistent static routes fail on MacOS 10.6.5 startup!

    - by verbalicious
    I'm unable to get static routes to persist a reboot on Mac OS 10.6.5. I've tried all of the methods prescribed in Google search results, and previous posts on this site. I've tried manually creating a launchd daemon, and used RouteSplit's launchd daemon to no avail. It's clear that the interface is not ready when these methods attempt to apply the route. This workstation in question is getting its IP from DHCP and probably hasn't gotten its DHCP lease when the command runs. We're able to apply the route by hand when logged in, but not through startup methods. Is there another way to apply this route by sneaking the command into something later, but before the login window appears to the user? Here is some relevant log info from system.log. You can see the "route: writing to routing socket: Network is unreachable" errors where my launchd script fires off. I've tried adding extra "sleep" and "ipconfig waitall" statements later in the script but this doesn't fly. Dec 15 19:30:41 localhost com.apple.launchd[1]: *** launchd[1] has started up. *** Dec 15 19:30:45 localhost mDNSResponder[18]: mDNSResponder mDNSResponder-258.13 (Oct 8 2010 17:10:30) starting Dec 15 19:30:47 localhost configd[15]: bootp_session_transmit: bpf_write(en1) failed: Network is down (50) Dec 15 19:30:47 localhost configd[15]: DHCP en1: INIT transmit failed Dec 15 19:30:47 localhost configd[15]: network configuration changed. Dec 15 19:30:47 Administrators-MacBook-Pro configd[15]: setting hostname to "Administrators-MacBook-Pro.local" Dec 15 19:30:47 Administrators-MacBook-Pro blued[16]: Apple Bluetooth daemon started Dec 15 19:30:52 Administrators-MacBook-Pro syslog[67]: routes.sh: Starting RouteSplit Dec 15 19:30:53 Administrators-MacBook-Pro com.apple.usbmuxd[41]: usbmuxd-207 built for iTunesTenOne on Oct 19 2010 at 13:50:35, running 64 bit Dec 15 19:30:54 Administrators-MacBook-Pro /System/Library/CoreServices/loginwindow.app/Contents/MacOS/loginwindow[50]: Login Window Application Started Dec 15 19:30:55 Administrators-MacBook-Pro bootlog[61]: BOOT_TIME: 1292459441 0 Dec 15 19:30:55 Administrators-MacBook-Pro syslog[86]: routes.sh: static route 192.168.0.0/23 192.168.2.2 Dec 15 19:30:55 Administrators-MacBook-Pro net.routes.static[65]: route: writing to routing socket: Network is unreachable Dec 15 19:30:55 Administrators-MacBook-Pro net.routes.static[65]: add net 192.168.0.0: gateway 192.168.2.2: Network is unreachable Dec 15 19:30:57 Administrators-MacBook-Pro org.apache.httpd[38]: httpd: Could not reliably determine the server's fully qualified domain name, using Administrators-MacBook-Pro.local for ServerName Dec 15 19:30:58 Administrators-MacBook-Pro loginwindow[50]: Login Window Started Security Agent Dec 15 19:30:58 Administrators-MacBook-Pro WindowServer[89]: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged. Dec 15 19:30:58 Administrators-MacBook-Pro com.apple.WindowServer[89]: Wed Dec 15 19:30:58 Administrators-MacBook-Pro.local WindowServer[89] <Error>: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged. Dec 15 19:31:18 Administrators-MacBook-Pro configd[15]: network configuration changed. Dec 15 19:31:19 administrators-macbook-pro configd[15]: setting hostname to "administrators-macbook-pro.local" Dec 15 19:31:25 administrators-macbook-pro _mdnsresponder[121]: /usr/libexec/ntpd-wrapper: scutil key State:/Network/Global/DNS not present after 30 seconds Dec 15 19:31:25 administrators-macbook-pro _mdnsresponder[124]: sntp options: a=2 v=1 e=0.100 E=5.000 P=2147483647.000 Dec 15 19:31:25 administrators-macbook-pro _mdnsresponder[124]: d=15 c=5 x=0 op=1 l=/var/run/sntp.pid f= time.apple.com Dec 15 19:31:25 administrators-macbook-pro _mdnsresponder[124]: sntp: getaddrinfo(hostname, ntp) failed with nodename nor servname provided, or not known Dec 15 19:31:27 administrators-macbook-pro configd[15]: network configuration changed. Dec 15 19:31:27 Administrators-MacBook-Pro configd[15]: setting hostname to "Administrators-MacBook-Pro.local" Dec 15 19:31:27 Administrators-MacBook-Pro ntpd[37]: Cannot find existing interface for address 17.151.16.20 Dec 15 19:31:27 Administrators-MacBook-Pro ntpd_initres[125]: ntpd indicates no data available! Dec 15 19:31:31 Administrators-MacBook-Pro sshd[128]: USER_PROCESS: 133 ttys000 Dec 15 19:31:37 Administrators-MacBook-Pro sudo[138]: administrator : TTY=ttys000 ; PWD=/Users/administrator ; USER=root ; COMMAND=/usr/bin/less /var/log/system.log ``You can see the following line in /var/log/kernel.log that shows the en0 interface coming up: Dec 15 19:30:51 Administrators-MacBook-Pro kernel[0]: Ethernet [AppleBCM5701Ethernet]: Link up on en0, 1-Gigabit, Full-duplex, No flow-control, Debug [796d,0f01,0de1,0300,c1e1,3800]

    Read the article

  • install python2.7.3 + numpy + scipy + matplotlib + scikits.statsmodels + pandas0.7.3 correctly

    - by boldnik
    ...using Linux (xubuntu). How to install python2.7.3 + numpy + scipy + matplotlib + scikits.statsmodels + pandas0.7.3 correctly ? My final aim is to have them working. The problem: ~$ python --version Python 2.7.3 so i already have a system-default 2.7.3, which is good! ~$ dpkg -s python-numpy Package: python-numpy Status: install ok installed and i already have numpy installed! great! But... ~$ python Python 2.7.3 (default, Oct 23 2012, 01:07:38) [GCC 4.6.1] on linux2 Type "help", "copyright", "credits" or "license" for more information. >>> import numpy as nmp Traceback (most recent call last): File "<stdin>", line 1, in <module> ImportError: No module named numpy this module couldn't be find by python. The same with scipy, matplotlib. Why? ~$ sudo apt-get install python-numpy [...] Reading package lists... Done Building dependency tree Reading state information... Done python-numpy is already the newest version. [...] why it does not see numpy and others ? update: >>> import sys >>> print sys.path ['', '/usr/local/lib/python27.zip', '/usr/local/lib/python2.7', '/usr/local/lib/python2.7/plat-linux2', '/usr/local/lib/python2.7/lib-tk', '/usr/local/lib/python2.7/lib-old', '/usr/local/lib/python2.7/lib-dynload', '/usr/local/lib/python2.7/site-packages'] >>> so i do have /usr/local/lib/python2.7 ~$ pip freeze Warning: cannot find svn location for distribute==0.6.16dev-r0 BzrTools==2.4.0 CDApplet==1.0 [...] matplotlib==1.0.1 mutagen==1.19 numpy==1.5.1 [...] pandas==0.7.3 papyon==0.5.5 [...] pytz==2012g pyxdg==0.19 reportlab==2.5 scikits.statsmodels==0.3.1 scipy==0.11.0 [...] zope.interface==3.6.1 as you can see, those modules are already installed! But! ls -la /usr/local/lib/ gives ONLY python2.7 dir. And still ~$ python -V Python 2.7.3 and import sys sys.version '2.7.3 (default, Oct 23 2012, 01:07:38) \n[GCC 4.6.1]' updated: Probably I've missed another instance... One at /usr/Python-2.7.3/ and second (seems to be installed "by hands" far far ago) at /usr/python2.7.3/Python-2.7.3/ But how two identical versions can work at the same time??? Probably, one of them is "disabled" (not used by any program, but I don't know how to check if any program uses it). ~$ ls -la /usr/bin/python* lrwxrwxrwx 1 root root 9 2011-11-01 11:11 /usr/bin/python -> python2.7 -rwxr-xr-x 1 root root 2476800 2012-09-28 19:48 /usr/bin/python2.6 -rwxr-xr-x 1 root root 1452 2012-09-28 19:45 /usr/bin/python2.6-config -rwxr-xr-x 1 root root 2586060 2012-07-21 01:42 /usr/bin/python2.7 -rwxr-xr-x 1 root root 1652 2012-07-21 01:40 /usr/bin/python2.7-config lrwxrwxrwx 1 root root 9 2011-10-05 23:53 /usr/bin/python3 -> python3.2 lrwxrwxrwx 1 root root 11 2011-09-06 02:04 /usr/bin/python3.2 -> python3.2mu -rwxr-xr-x 1 root root 2852896 2011-09-06 02:04 /usr/bin/python3.2mu lrwxrwxrwx 1 root root 16 2011-10-08 19:50 /usr/bin/python-config -> python2.7-config there is a symlink python-python2.7, maybe I can ln -f -s this link to exact /usr/Python-2.7.3/python destination without harm ?? And how correctly to remove the 'copy' of 2.7.3?

    Read the article

  • cron.daily not running at the time it should?

    - by Mariano Martinez Peck
    My /etc/cron.daily scripts seem to be executing far later from what I understand they should. I am in Ubuntu and anacron is installed. If I do a sudo cat /var/log/syslog | grep cron I get something like: Aug 23 01:17:01 mymachine CRON[25171]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Aug 23 02:17:01 mymachine CRON[25588]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Aug 23 03:17:01 mymachine CRON[26026]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Aug 23 03:25:01 mymachine CRON[30320]: (root) CMD (test -x /usr/sbin/anacron || ( cd / && run-parts --report /etc/cron.daily )) Aug 23 04:17:01 mymachine CRON[26363]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Aug 23 05:17:01 mymachine CRON[26770]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Aug 23 06:17:01 mymachine CRON[27168]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Aug 23 07:17:01 mymachine CRON[27547]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Aug 23 07:30:01 mymachine CRON[2249]: (root) CMD (start -q anacron || :) Aug 23 07:30:02 mymachine anacron[2252]: Anacron 2.3 started on 2014-08-23 Aug 23 07:30:02 mymachine anacron[2252]: Will run job `cron.daily' in 5 min. Aug 23 07:30:02 mymachine anacron[2252]: Jobs will be executed sequentially Aug 23 07:35:02 mymachine anacron[2252]: Job `cron.daily' started As you can see, at 3:25 it tried to do something. But the cron.daily execution started really at 7:35. My /etc/crontab is: # /etc/crontab: system-wide crontab # Unlike any other crontab you don't have to run the `crontab' # command to install the new version when you edit this file # and files in /etc/cron.d. These files also have username fields, # that none of the other crontabs do. SHELL=/bin/sh PATH=/usr/local/sbin:/usr/local/bin:/sbin:/bin:/usr/sbin:/usr/bin # m h dom mon dow user command 17 * * * * root cd / && run-parts --report /etc/cron.hourly 25 3 * * * root test -x /usr/sbin/anacron || ( cd / && run-parts --report /etc/cron.daily ) 47 6 * * 7 root test -x /usr/sbin/anacron || ( cd / && run-parts --report /etc/cron.weekly ) 52 6 1 * * root test -x /usr/sbin/anacron || ( cd / && run-parts --report /etc/cron.monthly ) # From what I understand, daily scripts are indeed for 3:25. My /etc/anacrontab is: # /etc/anacrontab: configuration file for anacron # See anacron(8) and anacrontab(5) for details. SHELL=/bin/sh PATH=/usr/local/sbin:/usr/local/bin:/sbin:/bin:/usr/sbin:/usr/bin HOME=/root LOGNAME=root # These replace cron's entries 1 5 cron.daily run-parts --report /etc/cron.daily 7 10 cron.weekly run-parts --report /etc/cron.weekly @monthly 15 cron.monthly run-parts --report /etc/cron.monthly So...does someone know why my cron started to do something at 3:25 but then really start the jobs at 7:35? Also..as you can see in the log, hourly jobs are being executed at correct time: hour and 17 minutes, which is exactly what I have in /etc/crontab Finally, from the logs, it seems my daily jobs are being actually run by anacron rather than cron? So cron finds nothing to run (at 3:25) and then anacron runs the jobs at 7:35? If true, how can I fix this? Thanks in advance,

    Read the article

  • Blank black screen with cursor after login -- RHEL5

    - by Sean O.
    I have a RHEL 5 machine here which is a Dell Precision T3500. I'm an Ubuntu guy, but I'm having a heck of a time with this machine. After processing its first security update, we cannot log in via the gdm greeter. A new kernel was installed; then I installed the nVidia drivers for our Quadro NVS 295. I know the X configuration is valid because the gdm greeter does display; however, upon login all we can get is a blank, black screen with a cursor. I thought perhaps our python installation was corrupted but a reinstall via yum has not helped. I have searched & googled extensively for a potential fix for this and can find nothing. Below are outputs from uname, a tail of an error in /var/log/messages, and the Xorg.conf. Can anyone suggest a course of action? [sean@cheetah ~]$ uname -a Linux cheetah.*.* 2.6.18-308.8.1.el5 #1 SMP Fri May 4 16:43:02 EDT 2012 x86_64 x86_64 x86_64 GNU/Linux [sean@cheetah ~]$ sudo tail /var/log/messages Jun 5 15:03:04 cheetah gconfd (sean-4592): Resolved address "xml:readonly:/etc/gconf/gconf.xml.defaults" to a read-only configuration source at position 2 Jun 5 15:03:05 cheetah hcid[3855]: Default passkey agent (:1.8, /org/bluez/applet) registered Jun 5 15:03:05 cheetah pcscd: winscard.c:304:SCardConnect() Reader E-Gate 0 0 Not Found Jun 5 15:03:05 cheetah last message repeated 2 times Jun 5 15:03:06 cheetah gconfd (sean-4592): Resolved address "xml:readwrite:/home/sean/.gconf" to a writable configuration source at position 0 Jun 5 15:03:06 cheetah setroubleshoot: [program.ERROR] exception ImportError: /usr/lib/libatk-1.0.so.0: undefined symbol: g_assertion_message_expr Traceback (most recent call last): File "/usr/bin/sealert", line 952, in ? from setroubleshoot.gui_utils import * File "/usr/lib/python2.4/site-packages/setroubleshoot/gui_utils.py", line 26, in ? import gtk File "/usr/lib64/python2.4/site-packages/gtk-2.0/gtk/__init__.py", line 48, in ? from gtk import _gtk ImportError: /usr/lib/libatk-1.0.so.0: undefined symbol: g_assertion_message_expr Jun 5 15:03:07 cheetah setroubleshoot: [program.ERROR] exception ImportError: /usr/lib/libatk-1.0.so.0: undefined symbol: g_assertion_message_expr Traceback (most recent call last): File "/usr/bin/sealert", line 952, in ? from setroubleshoot.gui_utils import * File "/usr/lib/python2.4/site-packages/setroubleshoot/gui_utils.py", line 26, in ? import gtk File "/usr/lib64/python2.4/site-packages/gtk-2.0/gtk/__init__.py", line 48, in ? from gtk import _gtk ImportError: /usr/lib/libatk-1.0.so.0: undefined symbol: g_assertion_message_expr Jun 5 15:03:08 cheetah pcscd: winscard.c:304:SCardConnect() Reader E-Gate 0 0 Not Found Jun 5 15:07:01 cheetah ntpd[4114]: synchronized to 64.16.211.38, stratum 3 Jun 5 15:07:01 cheetah ntpd[4114]: kernel time sync enabled 0001 [sean@cheetah ~]$ cat /etc/X11/xorg.conf # nvidia-xconfig: X configuration file generated by nvidia-xconfig # nvidia-xconfig: version 295.53 ([email protected]) Sat May 12 00:34:20 PDT 2012 # Xorg configuration created by system-config-display Section "ServerLayout" Identifier "single head configuration" Screen 0 "Screen0" 0 0 InputDevice "Mouse0" "CorePointer" InputDevice "Keyboard0" "CoreKeyboard" EndSection Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/input/mice" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" Identifier "Keyboard0" Driver "kbd" Option "XkbModel" "pc105" Option "XkbLayout" "us" EndSection Section "Monitor" ### Comment all HorizSync and VertSync values to use DDC: ### Comment all HorizSync and VertSync values to use DDC: Identifier "Monitor0" ModelName "LCD Panel 1600x1200" HorizSync 31.5 - 74.7 VertRefresh 56.0 - 65.0 Option "dpms" EndSection Section "Device" Identifier "Videocard0" Driver "nvidia" EndSection Section "Screen" Identifier "Screen0" Device "Videocard0" Monitor "Monitor0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection

    Read the article

  • Improving TCP performance over a gigabit network with lots of connections and high traffic of small packets

    - by MinimeDJ
    I’m trying to improve my TCP throughput over a “gigabit network with lots of connections and high traffic of small packets”. My server OS is Ubuntu 11.10 Server 64bit. There are about 50.000 (and growing) clients connected to my server through TCP Sockets (all on the same port). 95% of of my packets have size of 1-150 bytes (TCP header and payload). The rest 5% vary from 150 up to 4096+ bytes. With the config below my server can handle traffic up to 30 Mbps (full duplex). Can you please advice best practice to tune OS for my needs? My /etc/sysctl.cong looks like this: kernel.pid_max = 1000000 net.ipv4.ip_local_port_range = 2500 65000 fs.file-max = 1000000 # net.core.netdev_max_backlog=3000 net.ipv4.tcp_sack=0 # net.core.rmem_max = 16777216 net.core.wmem_max = 16777216 net.core.somaxconn = 2048 # net.ipv4.tcp_rmem = 4096 87380 16777216 net.ipv4.tcp_wmem = 4096 65536 16777216 # net.ipv4.tcp_synack_retries = 2 net.ipv4.tcp_syncookies = 1 net.ipv4.tcp_mem = 50576 64768 98152 # net.core.wmem_default = 65536 net.core.rmem_default = 65536 net.ipv4.tcp_window_scaling=1 # net.ipv4.tcp_mem= 98304 131072 196608 # net.ipv4.tcp_timestamps = 0 net.ipv4.tcp_rfc1337 = 1 net.ipv4.ip_forward = 0 net.ipv4.tcp_congestion_control=cubic net.ipv4.tcp_tw_recycle = 0 net.ipv4.tcp_tw_reuse = 0 # net.ipv4.tcp_orphan_retries = 1 net.ipv4.tcp_fin_timeout = 25 net.ipv4.tcp_max_orphans = 8192 Here are my limits: $ ulimit -a core file size (blocks, -c) 0 data seg size (kbytes, -d) unlimited scheduling priority (-e) 0 file size (blocks, -f) unlimited pending signals (-i) 193045 max locked memory (kbytes, -l) 64 max memory size (kbytes, -m) unlimited open files (-n) 1000000 pipe size (512 bytes, -p) 8 POSIX message queues (bytes, -q) 819200 real-time priority (-r) 0 stack size (kbytes, -s) 8192 cpu time (seconds, -t) unlimited max user processes (-u) 1000000 [ADDED] My NICs are the following: $ dmesg | grep Broad [ 2.473081] Broadcom NetXtreme II 5771x 10Gigabit Ethernet Driver bnx2x 1.62.12-0 (2011/03/20) [ 2.477808] bnx2x 0000:02:00.0: eth0: Broadcom NetXtreme II BCM57711E XGb (A0) PCI-E x4 5GHz (Gen2) found at mem fb000000, IRQ 28, node addr d8:d3:85:bd:23:08 [ 2.482556] bnx2x 0000:02:00.1: eth1: Broadcom NetXtreme II BCM57711E XGb (A0) PCI-E x4 5GHz (Gen2) found at mem fa000000, IRQ 40, node addr d8:d3:85:bd:23:0c [ADDED 2] ethtool -k eth0 Offload parameters for eth0: rx-checksumming: on tx-checksumming: on scatter-gather: on tcp-segmentation-offload: on udp-fragmentation-offload: off generic-segmentation-offload: on generic-receive-offload: on large-receive-offload: on rx-vlan-offload: on tx-vlan-offload: on ntuple-filters: off receive-hashing: off [ADDED 3] sudo ethtool -S eth0|grep -vw 0 NIC statistics: [1]: rx_bytes: 17521104292 [1]: rx_ucast_packets: 118326392 [1]: tx_bytes: 35351475694 [1]: tx_ucast_packets: 191723897 [2]: rx_bytes: 16569945203 [2]: rx_ucast_packets: 114055437 [2]: tx_bytes: 36748975961 [2]: tx_ucast_packets: 194800859 [3]: rx_bytes: 16222309010 [3]: rx_ucast_packets: 109397802 [3]: tx_bytes: 36034786682 [3]: tx_ucast_packets: 198238209 [4]: rx_bytes: 14884911384 [4]: rx_ucast_packets: 104081414 [4]: rx_discards: 5828 [4]: rx_csum_offload_errors: 1 [4]: tx_bytes: 35663361789 [4]: tx_ucast_packets: 194024824 [5]: rx_bytes: 16465075461 [5]: rx_ucast_packets: 110637200 [5]: tx_bytes: 43720432434 [5]: tx_ucast_packets: 202041894 [6]: rx_bytes: 16788706505 [6]: rx_ucast_packets: 113123182 [6]: tx_bytes: 38443961940 [6]: tx_ucast_packets: 202415075 [7]: rx_bytes: 16287423304 [7]: rx_ucast_packets: 110369475 [7]: rx_csum_offload_errors: 1 [7]: tx_bytes: 35104168638 [7]: tx_ucast_packets: 184905201 [8]: rx_bytes: 12689721791 [8]: rx_ucast_packets: 87616037 [8]: rx_discards: 2638 [8]: tx_bytes: 36133395431 [8]: tx_ucast_packets: 196547264 [9]: rx_bytes: 15007548011 [9]: rx_ucast_packets: 98183525 [9]: rx_csum_offload_errors: 1 [9]: tx_bytes: 34871314517 [9]: tx_ucast_packets: 188532637 [9]: tx_mcast_packets: 12 [10]: rx_bytes: 12112044826 [10]: rx_ucast_packets: 84335465 [10]: rx_discards: 2494 [10]: tx_bytes: 36562151913 [10]: tx_ucast_packets: 195658548 [11]: rx_bytes: 12873153712 [11]: rx_ucast_packets: 89305791 [11]: rx_discards: 2990 [11]: tx_bytes: 36348541675 [11]: tx_ucast_packets: 194155226 [12]: rx_bytes: 12768100958 [12]: rx_ucast_packets: 89350917 [12]: rx_discards: 2667 [12]: tx_bytes: 35730240389 [12]: tx_ucast_packets: 192254480 [13]: rx_bytes: 14533227468 [13]: rx_ucast_packets: 98139795 [13]: tx_bytes: 35954232494 [13]: tx_ucast_packets: 194573612 [13]: tx_bcast_packets: 2 [14]: rx_bytes: 13258647069 [14]: rx_ucast_packets: 92856762 [14]: rx_discards: 3509 [14]: rx_csum_offload_errors: 1 [14]: tx_bytes: 35663586641 [14]: tx_ucast_packets: 189661305 rx_bytes: 226125043936 rx_ucast_packets: 1536428109 rx_bcast_packets: 351 rx_discards: 20126 rx_filtered_packets: 8694 rx_csum_offload_errors: 11 tx_bytes: 548442367057 tx_ucast_packets: 2915571846 tx_mcast_packets: 12 tx_bcast_packets: 2 tx_64_byte_packets: 35417154 tx_65_to_127_byte_packets: 2006984660 tx_128_to_255_byte_packets: 373733514 tx_256_to_511_byte_packets: 378121090 tx_512_to_1023_byte_packets: 77643490 tx_1024_to_1522_byte_packets: 43669214 tx_pause_frames: 228 Some info about SACK: When to turn TCP SACK off?

    Read the article

  • How do I get my ubuntu server to listen for database connections?

    - by Bob Flemming
    I am having a problems connecting to my database outside of phpmyadmin. Im pretty sure this is because my server isn't listening on port 3306. When I type: sudo netstat -ntlp on my OTHER working server I can see the following line: tcp 0 0 0.0.0.0:3306 0.0.0.0:* LISTEN 20445/mysqld However, this line does not appear on the server I am having difficulty with. How do I make my sever listen for mysql connections? Here my my.conf file: # # The MySQL database server configuration file. # # You can copy this to one of: # - "/etc/mysql/my.cnf" to set global options, # - "~/.my.cnf" to set user-specific options. # # One can use all long options that the program supports. # Run program with --help to get a list of available options and with # --print-defaults to see which it would actually understand and use. # # For explanations see # http://dev.mysql.com/doc/mysql/en/server-system-variables.html # This will be passed to all mysql clients # It has been reported that passwords should be enclosed with ticks/quotes # escpecially if they contain "#" chars... # Remember to edit /etc/mysql/debian.cnf when changing the socket location. [client] port = 3306 socket = /var/run/mysqld/mysqld.sock # Here is entries for some specific programs # The following values assume you have at least 32M ram # This was formally known as [safe_mysqld]. Both versions are currently parsed. [mysqld_safe] socket = /var/run/mysqld/mysqld.sock nice = 0 [mysqld] # # * Basic Settings # user = mysql pid-file = /var/run/mysqld/mysqld.pid socket = /var/run/mysqld/mysqld.sock port = 3306 basedir = /usr datadir = /var/lib/mysql tmpdir = /tmp lc-messages-dir = /usr/share/mysql #skip-networking=off #skip_networking=off #skip-external-locking # # Instead of skip-networking the default is now to listen only on # localhost which is more compatible and is not less secure. #bind-address = 0.0.0.0 # # * Fine Tuning # key_buffer = 64M max_allowed_packet = 64M thread_stack = 650K thread_cache_size = 32 # This replaces the startup script and checks MyISAM tables if needed # the first time they are touched myisam-recover = BACKUP #max_connections = 100 #table_cache = 64 #thread_concurrency = 10 # # * Query Cache Configuration # query_cache_limit = 2M query_cache_size = 32M # # * Logging and Replication # # Both location gets rotated by the cronjob. # Be aware that this log type is a performance killer. # As of 5.1 you can enable the log at runtime! #general_log_file = /var/log/mysql/mysql.log #general_log = 1 # # Error logging goes to syslog due to /etc/mysql/conf.d/mysqld_safe_syslog.cnf. # # Here you can see queries with especially long duration #log_slow_queries = /var/log/mysql/mysql-slow.log #long_query_time = 2 #log-queries-not-using-indexes # # The following can be used as easy to replay backup logs or for replication. # note: if you are setting up a replication slave, see README.Debian about # other settings you may need to change. #server-id = 1 #log_bin = /var/log/mysql/mysql-bin.log expire_logs_days = 10 max_binlog_size = 100M #binlog_do_db = include_database_name #binlog_ignore_db = include_database_name # # * InnoDB # # InnoDB is enabled by default with a 10MB datafile in /var/lib/mysql/. # Read the manual for more InnoDB related options. There are many! # # * Security Features # # Read the manual, too, if you want chroot! # chroot = /var/lib/mysql/ # # For generating SSL certificates I recommend the OpenSSL GUI "tinyca". # # ssl-ca=/etc/mysql/cacert.pem # ssl-cert=/etc/mysql/server-cert.pem # ssl-key=/etc/mysql/server-key.pem [mysqldump] quick quote-names max_allowed_packet = 32M [mysql] #no-auto-rehash # faster start of mysql but no tab completition [isamchk] key_buffer = 32M # # * IMPORTANT: Additional settings that can override those from this file! # The files must end with '.cnf', otherwise they'll be ignored. # !includedir /etc/mysql/conf.d/

    Read the article

  • Making sense of S.M.A.R.T

    - by James
    First of all, I think everyone knows that hard drives fail a lot more than the manufacturers would like to admit. Google did a study that indicates that certain raw data attributes that the S.M.A.R.T status of hard drives reports can have a strong correlation with the future failure of the drive. We find, for example, that after their first scan error, drives are 39 times more likely to fail within 60 days than drives with no such errors. First errors in re- allocations, offline reallocations, and probational counts are also strongly correlated to higher failure probabil- ities. Despite those strong correlations, we find that failure prediction models based on SMART parameters alone are likely to be severely limited in their prediction accuracy, given that a large fraction of our failed drives have shown no SMART error signals whatsoever. Seagate seems like it is trying to obscure this information about their drives by claiming that only their software can accurately determine the accurate status of their drive and by the way their software will not tell you the raw data values for the S.M.A.R.T attributes. Western digital has made no such claim to my knowledge but their status reporting tool does not appear to report raw data values either. I've been using HDtune and smartctl from smartmontools in order to gather the raw data values for each attribute. I've found that indeed... I am comparing apples to oranges when it comes to certain attributes. I've found for example that most Seagate drives will report that they have many millions of read errors while western digital 99% of the time shows 0 for read errors. I've also found that Seagate will report many millions of seek errors while Western Digital always seems to report 0. Now for my question. How do I normalize this data? Is Seagate producing millions of errors while Western digital is producing none? Wikipedia's article on S.M.A.R.T status says that manufacturers have different ways of reporting this data. Here is my hypothesis: I think I found a way to normalize (is that the right term?) the data. Seagate drives have an additional attribute that Western Digital drives do not have (Hardware ECC Recovered). When you subtract the Read error count from the ECC Recovered count, you'll probably end up with 0. This seems to be equivalent to Western Digitals reported "Read Error" count. This means that Western Digital only reports read errors that it cannot correct while Seagate counts up all read errors and tells you how many of those it was able to fix. I had a Seagate drive where the ECC Recovered count was less than the Read error count and I noticed that many of my files were becoming corrupt. This is how I came up with my hypothesis. The millions of seek errors that Seagate produces are still a mystery to me. Please confirm or correct my hypothesis if you have additional information. Here is the smart status of my western digital drive just so you can see what I'm talking about: james@ubuntu:~$ sudo smartctl -a /dev/sda smartctl version 5.38 [x86_64-unknown-linux-gnu] Copyright (C) 2002-8 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Device Model: WDC WD1001FALS-00E3A0 Serial Number: WD-WCATR0258512 Firmware Version: 05.01D05 User Capacity: 1,000,204,886,016 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 8 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Thu Jun 10 19:52:28 2010 PDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0027 179 175 021 Pre-fail Always - 4033 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 270 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0 9 Power_On_Hours 0x0032 098 098 000 Old_age Always - 1468 10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 262 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 46 193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 223 194 Temperature_Celsius 0x0022 105 102 000 Old_age Always - 42 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0

    Read the article

  • Vagrant (Virtualbox) host-only multiple node networking issue

    - by Lorin Hochstein
    I'm trying to use a multi-VM vagrant environment as a testbed for deploying OpenStack, and I've run into a networking problem with trying to communicate from one VM, to a VM-inside-of-a-VM. I have two Vagrant nodes, a cloud controller node and a compute node. I'm using host-only networking. My Vagrantfile looks like this: Vagrant::Config.run do |config| config.vm.box = "precise64" config.vm.define :controller do |controller_config| controller_config.vm.network :hostonly, "192.168.206.130" # eth1 controller_config.vm.network :hostonly, "192.168.100.130" # eth2 controller_config.vm.host_name = "controller" end config.vm.define :compute1 do |compute1_config| compute1_config.vm.network :hostonly, "192.168.206.131" # eth1 compute1_config.vm.network :hostonly, "192.168.100.131" # eth2 compute1_config.vm.host_name = "compute1" compute1_config.vm.customize ["modifyvm", :id, "--memory", 1024] end end When I try to start up a (QEMU-based) VM, it boots successfully on compute1, and its virtual nic (vnet0) is connected via a bridge, br100: root@compute1:~# brctl show 100 bridge name bridge id STP enabled interfaces br100 8000.08002798c6ef no eth2 vnet0 When the QEMU VM makes a request to the DHCP server (dnsmasq) running on controller, I can see the request reaches the controller because of the output on the syslog on the controller: Aug 6 02:34:56 precise64 dnsmasq-dhcp[12042]: DHCPDISCOVER(br100) fa:16:3e:07:98:11 Aug 6 02:34:56 precise64 dnsmasq-dhcp[12042]: DHCPOFFER(br100) 192.168.100.2 fa:16:3e:07:98:11 However, the DHCPOFFER never makes it back to the VM running on compute1. If I watch the requests using tcpdump on the vboxnet3 interface on my host machine that runs Vagrant (Mac OS X), I can see both the requests and the replies $ sudo tcpdump -i vboxnet3 -n port 67 or port 68 tcpdump: WARNING: vboxnet3: That device doesn't support promiscuous mode (BIOCPROMISC: Operation not supported on socket) tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on vboxnet3, link-type EN10MB (Ethernet), capture size 65535 bytes 22:51:20.694040 IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from fa:16:3e:07:98:11, length 280 22:51:20.694057 IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from fa:16:3e:07:98:11, length 280 22:51:20.696047 IP 192.168.100.1.67 > 192.168.100.2.68: BOOTP/DHCP, Reply, length 311 22:51:23.700845 IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from fa:16:3e:07:98:11, length 280 22:51:23.700876 IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from fa:16:3e:07:98:11, length 280 22:51:23.701591 IP 192.168.100.1.67 > 192.168.100.2.68: BOOTP/DHCP, Reply, length 311 22:51:26.705978 IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from fa:16:3e:07:98:11, length 280 22:51:26.705995 IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from fa:16:3e:07:98:11, length 280 22:51:26.706527 IP 192.168.100.1.67 > 192.168.100.2.68: BOOTP/DHCP, Reply, length 311 But, if I tcpdump on eth2 on compute, I only see the requests, not the replies: root@compute1:~# tcpdump -i eth2 -n port 67 or port 68 tcpdump: WARNING: eth2: no IPv4 address assigned tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on eth2, link-type EN10MB (Ethernet), capture size 65535 bytes 02:51:20.240672 IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from fa:16:3e:07:98:11, length 280 02:51:23.249758 IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from fa:16:3e:07:98:11, length 280 02:51:26.258281 IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from fa:16:3e:07:98:11, length 280 At this point, I'm stuck. I'm not sure why the DHCP replies aren't making it to the compute node. Perhaps it has something to do with the configuration of the VirtualBox virtual switch/router? Note that eth2 interfaces on both nodes have been set to promiscuous mode.

    Read the article

  • the font of xubuntu

    - by ubuntu
    HI: How to set the default font for different language in the xubuntu? For example, I am using xubuntu9.10(English release),and I do not like the default English and Chinese font. I have tried to use "Application-setting-appearance-fonts" to edit the default font,however it just work for the English. The default font of Chinese is "WenQuanYi Zen Hei". I do not like it. I want to use "Microsoft YaHei", I copy this file from my Win7 system. And I tried remove the "WenQuanYi Zen Hei" by "sudo aptitude remove ttf-wqy",it show me it is successfully removed. Also I have modify the file: /etc/fonts/conf.avail/69-language-selector-zh-cn.conf to: <fontconfig> <match target="pattern"> <test qual="any" name="family"> <string>serif</string> </test> <edit name="family" mode="prepend" binding="strong"> <string>Microsoft YaHei</string> <string>AR PL UMing CN</string> <string>AR PL ShanHeiSun Uni</string> <string>Bitstream Vera Serif</string> <string>DejaVu Serif</string> <string>AR PL UKai CN</string> <string>AR PL ZenKai Uni</string> </edit> </match> <match target="pattern"> <test qual="any" name="family"> <string>sans-serif</string> </test> <edit name="family" mode="prepend" binding="strong"> <string>Bitstream Vera Sans</string> <string>Microsoft YaHei</string> <string>DejaVu Sans</string> <string>AR PL UMing CN</string> <string>AR PL ShanHeiSun Uni</string> <string>AR PL UKai CN</string> <string>AR PL ZenKai Uni</string> </edit> </match> <match target="pattern"> <test qual="any" name="family"> <string>monospace</string> </test> <edit name="family" mode="prepend" binding="strong"> <string>Bitstream Vera Sans Mono</string> <string>Microsoft YaHei</string> <string>DejaVu Sans Mono</string> <string>AR PL UMing CN</string> <string>AR PL ShanHeiSun Uni</string> <string>AR PL UKai CN</string> <string>AR PL ZenKai Uni</string> </edit> </match> </fontconfig> However when I use the firefox, I found the title of the firefox window is not YaHei. See the image here So what is the problem?

    Read the article

  • the font of xubuntu

    - by ubuntu
    HI: How to set the default font for different language in the xubuntu? For example, I am using xubuntu9.10(English release),and I do not like the default English and Chinese font. I have tried to use "Application-setting-appearance-fonts" to edit the default font,however it just work for the English. The default font of Chinese is "WenQuanYi Zen Hei". I do not like it. I want to use "Microsoft YaHei", I copy this file from my Win7 system. And I tried remove the "WenQuanYi Zen Hei" by "sudo aptitude remove ttf-wqy",it show me it is successfully removed. Also I have modify the file: /etc/fonts/conf.avail/69-language-selector-zh-cn.conf to: <fontconfig> <match target="pattern"> <test qual="any" name="family"> <string>serif</string> </test> <edit name="family" mode="prepend" binding="strong"> <string>Microsoft YaHei</string> <string>AR PL UMing CN</string> <string>AR PL ShanHeiSun Uni</string> <string>Bitstream Vera Serif</string> <string>DejaVu Serif</string> <string>AR PL UKai CN</string> <string>AR PL ZenKai Uni</string> </edit> </match> <match target="pattern"> <test qual="any" name="family"> <string>sans-serif</string> </test> <edit name="family" mode="prepend" binding="strong"> <string>Bitstream Vera Sans</string> <string>Microsoft YaHei</string> <string>DejaVu Sans</string> <string>AR PL UMing CN</string> <string>AR PL ShanHeiSun Uni</string> <string>AR PL UKai CN</string> <string>AR PL ZenKai Uni</string> </edit> </match> <match target="pattern"> <test qual="any" name="family"> <string>monospace</string> </test> <edit name="family" mode="prepend" binding="strong"> <string>Bitstream Vera Sans Mono</string> <string>Microsoft YaHei</string> <string>DejaVu Sans Mono</string> <string>AR PL UMing CN</string> <string>AR PL ShanHeiSun Uni</string> <string>AR PL UKai CN</string> <string>AR PL ZenKai Uni</string> </edit> </match> </fontconfig> However when I use the firefox, I found the title of the firefox window is not YaHei. See the image here So what is the problem?

    Read the article

  • the font of xubuntu

    - by ubuntu
    HI: How to set the default font for different language in the xubuntu? For example, I am using xubuntu9.10(English release),and I do not like the default English and Chinese font. I have tried to use "Application-setting-appearance-fonts" to edit the default font,however it just work for the English. The default font of Chinese is "WenQuanYi Zen Hei". I do not like it. I want to use "Microsoft YaHei", I copy this file from my Win7 system. And I tried remove the "WenQuanYi Zen Hei" by "sudo aptitude remove ttf-wqy",it show me it is successfully removed. Also I have modify the file: /etc/fonts/conf.avail/69-language-selector-zh-cn.conf to: <fontconfig> <match target="pattern"> <test qual="any" name="family"> <string>serif</string> </test> <edit name="family" mode="prepend" binding="strong"> <string>Microsoft YaHei</string> <string>AR PL UMing CN</string> <string>AR PL ShanHeiSun Uni</string> <string>Bitstream Vera Serif</string> <string>DejaVu Serif</string> <string>AR PL UKai CN</string> <string>AR PL ZenKai Uni</string> </edit> </match> <match target="pattern"> <test qual="any" name="family"> <string>sans-serif</string> </test> <edit name="family" mode="prepend" binding="strong"> <string>Bitstream Vera Sans</string> <string>Microsoft YaHei</string> <string>DejaVu Sans</string> <string>AR PL UMing CN</string> <string>AR PL ShanHeiSun Uni</string> <string>AR PL UKai CN</string> <string>AR PL ZenKai Uni</string> </edit> </match> <match target="pattern"> <test qual="any" name="family"> <string>monospace</string> </test> <edit name="family" mode="prepend" binding="strong"> <string>Bitstream Vera Sans Mono</string> <string>Microsoft YaHei</string> <string>DejaVu Sans Mono</string> <string>AR PL UMing CN</string> <string>AR PL ShanHeiSun Uni</string> <string>AR PL UKai CN</string> <string>AR PL ZenKai Uni</string> </edit> </match> </fontconfig> However when I use the firefox, I found the title of the firefox window is not YaHei. See the image here So what is the problem?

    Read the article

< Previous Page | 186 187 188 189 190 191 192 193 194 195  | Next Page >