Search Results

Search found 6055 results on 243 pages for 'ryan max'.

Page 191/243 | < Previous Page | 187 188 189 190 191 192 193 194 195 196 197 198  | Next Page >

• UPS power requirements for server

  - by captainentropy

  Greetings! So, I just placed an order for a new server. The company recommended that I get a 3000W UPS. (!) As best as I could I calculated the following wattage consumption based on benchmarked data or datasheets provided by the manufacturers of each component: number watts **total watts** MoBo 1 240 240 CPUs (E5540) 2 80 160 RAID cards (3ware) 2 18 36 RAM (6x4GB) 6 3 18 DVD drive 1 7 7 floppy 1 2 2 RE4 drives 8 7 56 WD20 drives 8 6 48 Intel X25 SSD 2 0.15 0.3 total = 567 So that is for the PSU requirements only. The PSUs in the machine are a 720W for the master node and 800W each for two subsystems. That's a total of 2320W that can be delivered by these PSUs. But that is 4X the amount being consumed, at most, by the components. I didn't count case fans or the eSATA card (3W maybe?) or what the PSUs themselves require but assuming I double or triple my calculations I'm not even remotely close to the 3000W UPS I was suggested to get. They run at least $1100. I could get a 2000W for about $750 or a 1500W for $450 and still be well over my estimated power need. I don't think I need a whole lot of run time in the case of a power outage, maybe 20 minutes max, enough time to shutdown if the power doesn't come on within 5-10 minutes. Any thoughts? Am I off on my calculations? Did I overlook something major? If so what are your suggestions for a UPS? Thanks!

  Read the article

• How to handle sh: fetch: command not found

  - by Tyler Johnson

  Okay, I'm a noobie. I know how to build and compose a website, but I have no idea what I'm doing when it comes to servers and server commands, etc. I've recently had a problem with all of my sites on our servers going down all at once and then I have to go in and reboot the server for them to come up again. At first this was annoying, but now it is becoming agonizing as it now takes 3-4 reboots for the websites to come back up. I contacted support for my hosting, but they are not being very helpful. They just keep telling me what the issue might be and basically telling me that I'm going to have to look into it and figure it out, which really isn't possible since I know nothing. Anyway, here are the things they said were possible reasons: They said I have "strange logs" in my Apache webserver log, error: sh: fetch: command not found. My php.ini memory limit is: 256M which is very high. It should be 32M or 64M. Server is reaching Max Clients, meaning we have more than 150 visitors at a time. (They supposedly "fixed" this, but the sites/server are still going down) I have some Wordpress sites with plugins getting errors like: PHP Warning: pack(): Type H: illegal hex digit G in... PHP Fatal error: Cannot use object of type stdClass as array in... PHP Fatal error: Maximum execution time of 30 seconds exceeded in... PHP Fatal error: Call to undefined function file_exists() in... PHP Parse error: syntax error, unexpected '<' I know that's a lot, but I really am at wits end and have no idea what to do now. If anyone could maybe give me some advice or point me in the right direction I would greatly appreciate it! Thanks! Oh, and here are the specs for my server: RAM: 2048MB CPU Shares: 40 Primary Disk: 50GB Data Transfer: 75GB Port Speed: 5Mbps

  Read the article

• Attaching 3.5" desktop drive to MacBook SATA

  - by Kyle Cronin

  I have a mid-2007 MacBook that, according to the Apple Store, has suffered some liquid damage and requires a new logic board to operate correctly, a ~$750 repair I've been told (would normally be around ~$300 were it not for the "liquid damage"). The unit itself works fine - the only problem I've been having is that the system does not recognize the battery and will not charge it. Curiously, the system can still be powered by the battery and even recognizes when the power cord is detached by diming the backlight, but I digress. Now that this laptop will likely become a desktop, I'm wondering if it might be possible to attach a desktop drive. I recently purchased a 2TB SATA drive and I'm wondering if it's possible to somehow attach it where the current internal drive connects. Obviously the drive itself will not fit inside the device, but as the unit will spend the rest of its days on my desk, that's not really much of an issue. My main questions are: Is this possible? If so, how would I connect the drive? Would a SATA extender cable work? Is the SATA port on my MacBook capable of powering a desktop drive? Or should I just get a SATA male-to-female cable and see if I can power the drive through other means (a cheap power supply, for example) The disk I'm referring to is the Hitachi Deskstar HD32000. Though I couldn't find that exact model on Hitachi's support site, these are the power requirements for a similar drive, the 7K2000 (2TB, 7200RPM, SATA II): Power Requirement +5 VDC (+/-5%) +12 VDC (+/-10%) Startup current (A, max.) 1.2 (+5V), 2.0 (+12V) Idle (W) 7.5 From what I've read, 2.5" drives require 5V, meaning that my MacBook obviously is capable of producing it. The specs seem to suggest that this drive seems capable of accepting it instead of the typical 12V - is this an accurate interpretation of the power requirements? Or does it need both 12V and 5V?

  Read the article

• WRT54GL Tomato Router in Client wireless mode to an iPhone Personal Hotspot

  - by Gordo

  I am trying to connect a router with Tomato firmware to an iPhone 4. The goal is to connect to the Personal Hotspot in Client Wireless mode. This should allow wired and wireless users to connect to the router rather then the iPhone. In theory this should be possible but I am having difficulty. Router Linksys WRT54GL Tomato 1.28.1816 firmware iPhone iPhone 4 iOS 5.1 (9B176) Carrier Rogers Wireless Personal Hotspot works with other devices, wifi/bluetooth/usb iPhone Personal Hotspot settings Mode: B/G Security: WPA or WPA2 Personal Encryption: AES Router IP: 172.20.10.1 Subnet: 172.20.10.0 Min IP: 172.20.10.2 Max IP: 172.20.10.14 maximum number of wireless tethered hosts is 5 I have followed the directions here: http://www.wi-fiplanet.com/tutorials/article.php/3810281 Ensured that the router subnet does not 'collide' with the iPhone subnet. Here is the configuration of the Tomato 'Basic - Network - Wireless' section: http://i.stack.imgur.com/pbmTB.png I have tried several variations of this configuration, but nothing seems to work. NOTE: I have successfully connected to my own wifi network in Wireless Client mode, so I am confident that there are no bad cables or other hardware issues. I would prefer to use Tomato, but DD-WRT maybe my only other option. Thanks!

  Read the article

• limiting connections from tomcat to IIS - proxy? iptables?

  - by Chris Phillips

  Howdy, I've webapp on tomcat6 which is connecting to an M$ PlayReady DRM instance on IIS6.0 The performance is seen to be best when we bench mark (using ab) the DRM service with 25 concurrent connections, which gives about 250 requests per second, which is ace. higher concurrent connections results in TCP/IP timeouts and other lower level mess. But there is no way to control how the tomcat app connects to the service - it's not internally managing a pool of connections etc, they are all isolated http connections to the server. Ideally I'd like a situation where we can have 25 http 1.1 connections being kept alive permanently from tomcat and requesting the licenses through this static pool of connections, which I think would the best performance. But this is not in the code, so was looking for a way to possibly simulate this at the Linux level. I was possibly thinking that iptables connlimit might be able to gracefully handle these connections, but whilst it could limit, it'd probably still annoy the app. What about a proxy? nginx (or possibly squid) seems potentially appealing to run on the tomcat server and hit on localhost as we might want to add additional DRM servers to use under load balance anyway. Could this take 100 incoming connections from tomcat, accept them all and proxy over the the IIS server in a more respectful manner? Any other angles? EDIT - looking over mod_proxy for apache, which we are already using for conventional use on an apache instance in front of this tomcat instance, might be ideal. I can set a max value on the proxy_pass to only allow 25 connections, and keep them alive permanently. Is that my answer? Many thanks, Chris

  Read the article

• New to building computers worried about temps

  - by dave

  I'm new to building my own computers and I was wondering about maximum temperatures. I understand that the room temp can affect the computers temp but how relevent is it? I understand that if my room temp is 20°C none of my computer parts could be lower than that. But if my room is 27°C instead of 20°C would this cause my computers parts to heat up more/faster? My new computer I built myself for gaming is i7 2600k 16gb ram ddr3 1600 hd6970 2 gb 240gb ssd ( bought a nas with 3 2tb drives in raid 5 for my home network ) 850w modular psu I also have my old hp computer i3 2120 8gb ram hd6770 1tb hdd I also have 3 laptops in my household, but I am not worried about their temps, they heat up my legs but they are never under stress. Due to size and money reasons I used an old case and it only has one of the sides left on it. Is this bad for the computer and will the extra dust cause problems? Or should I leave it this way or take the missus wrath and buy a case? If so is there any certain case I should get? I don't care about looks I just want card reader and usb slots and for it to run as cool or cooler than now, my case has 1 fan. Also what are the max temps for my new and old computer parts? Is 40°C under load ok for my CPU, what about 70°C for my GPU is that ok too, or should I worry? What are normal and safe temps for my components? I have looked around but there seem to be lots of different answers. I know that 100°C is bad but I want my parts to last as long as possible and this site always seems to give good replies without arguing or flaming.

  Read the article

• MySQL consuming all system memory on INSERT ... SELECT

  - by siete

  The mysql daemon is getting killed because Linux is reaching out of memory: Oct 24 07:41:23 <hostname> kernel: [82297.673701] Out of memory: kill process 13816 (mysqld) score 1839626 or a child There is a link with some workaround on this. That only happen when executing a query INSERT ... SELECT with a very huge resulset. MySQLTuner script displays that maximum theorical memory is less than 8GB, but top and munim shows that is getting over all RAM and swap available: [--] Total buffers: 560.0M global + 72.2M per thread (100 max threads) [OK] Maximum possible memory usage: 7.6G (43% of installed RAM) I'm tried to tune some options with not results, there are the relevant ones: skip-locking max_connections = 100 key_buffer_size = 512M max_allowed_packet = 32M table_open_cache = 2000 open_files_limit = 3000 sort_buffer_size = 16M read_buffer_size = 16M read_rnd_buffer_size = 8M myisam_sort_buffer_size = 64M thread_cache_size = 4 query_cache_size = 16M query_cache_limit = 2M thread_concurrency = 4 join_buffer_size = 32M tmp_table_size = 32M max_heap_table_size = 32M query_cache_limit = 8M bulk_insert_buffer_size = 64M myisam_max_sort_file_size = 50GB myisam_mmap_size = 10GB And there is a system resume: OS: Linux Debian "Squeeze" 6.0.8 (upgraded yesterday) RAM: 18GB Swap: 18GB MySQL: 5.1.72-2 (official Debain release) At this moment, update or change OS or MySQL version is not possible, there is any option that can help and i missed? Sorry by my english, and thank you in advance! Edit: I'm only using MyISAM tables, and cannot change to InnoDB.

  Read the article

• How important is dual-gigabit lan for a super user's home NAS?

  - by Andrew

  Long story short: I'm building my own home server based on Ubuntu with 4 drives in RAID 10. Its primary purpose will be NAS and backup. Would I be making a terrible mistake by building a NAS Server with a single Gigabit NIC? Long story long: I know the absolute max I can get out of a single Gigabit port is 125MB/s, and I want this NAS to be able to handle up to 6 computers accessing files simultaneously, with up to two of them streaming video. With Ubuntu NIC-bonding and the performance of RAID 10, I can theoretically double my throughput and achieve 250MB/s (ok, not really, but it would be faster). The drives have an average read throughput of 83.87MB/s according to Tom's Hardware. The unit itself will be based on the Chenbro ES34069-BK-180 case. With my current hardware choices, it'll have this motherboard with a Core i3 CPU and 8GB of RAM. Overkill, I know, but this server will be doing other things as well (like transcoding video). Unfortunately, the only Mini-ITX boards I can find with dual-gigabit and 6 SATA ports are Intel Atom-based, and I need more processing power than an Atom has to offer. I would love to find a board with 6 SATA ports and two Gigabit LAN ports that supports a Core i3 CPU. So far, my search has come up empty. Thus, my dilemma. Should I hold out for such a board, go with an Atom-based solution, or stick with my current single-gigabit configuration? I know there are consumer NAS units with just one gigabit interface (probably most of them), but I think I will demand a lot more from my server than the average home user. Any advice is appreciated. Thanks.

  Read the article

• Computer sponteously reboots when doing heavy file copy to/from disk

  - by Mark Hosang

  I've been fighting with this problem for the last 3 weeks where my machine will just instantly reboot. No BSOD, and when i checked the event log all that was reported was the generic "Kernal-power" error with the detailed information pointing to a hard crash. This is a machine that was working for 18 months before these crashes started happening. When they started happening is after I added 3 HDs in a RAID-5, upped the memory to 12gb, moved to a new house, added a SSD and added about 5 case fans. I have thus eliminated the RAID, and determined that the SSD was not the cause (because it was still crashing even though the ssd wasn't connected). I've run memtest several times over night with no memory problems showing up. I've run IntelBurnTest to max out the cpu to see if it was a heat issue and at full tilt after 20 min it was only at 85C and the machine didn't crash. I also took a look at the voltages during this test, with a screenshot at the bottom of this post I've ruled out a software issue by reinstalling windows 7 ultimate x64 a total of 5 times, but even during that the install it crashes. Happens sometime during file copying at the beginning, or during uncompressing files, or sometimes during running windows update. The only discernible pattern i can see is that it seems to crash when hard disks might be spinning up or when they are accessed heavily from large file transfers. My current guess is that it is probably an issue with the MB, PSU or the power coming through the outlet. Any suggestions of what i could try to troubleshoot or what may be wrong? Specs PSU: Seasonic M12 700w Mem: 12gb CPU: i7-920 with stock heatsink MB: Asus P6T HDs: 3 green WD and 1 Corsair force 3 120b with 1.3.3 firmware Running full tilt voltages Idling Voltages

  Read the article

• Why Wireshark does not recognize this HTTP response?

  - by Alois Mahdal

  I have a trivial CGI script that outputs simple text content. It's written in Perl and using CGI module and it specifies only the most basic headers: print $q->header( -type => 'text/plain', -Content_length => $length, ); print $stuff; There's no apparent issue with functionality, but I'm confused about the fact that Wireshark does not recognize the HTTP response as HTTP--it's marked as TCP. Here is request and response: GET /cgi-bin/memfile/memfile.pl?mbytes=1 HTTP/1.1 Host: 10.6.130.38 User-Agent: Mozilla/5.0 (Windows NT 6.1; WOW64; rv:11.0) Gecko/20100101 Firefox/11.0 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: cs,en-us;q=0.7,en;q=0.3 Accept-Encoding: gzip, deflate Connection: keep-alive HTTP/1.1 200 OK Date: Thu, 05 Apr 2012 18:52:23 GMT Server: Apache/2.2.15 (Win32) mod_ssl/2.2.15 OpenSSL/0.9.8m Content-length: 1048616 Keep-Alive: timeout=5, max=100 Connection: Keep-Alive Content-Type: text/plain; charset=ISO-8859-1 XXXXXXXX... And here is the packet overview (Full packet is here on pastebin) No. Time Source srcp Destination dstp Protocol Info tcp.stream abstime 5 0.112749 10.6.130.38 80 10.6.130.53 48072 TCP [TCP segment of a reassembled PDU] 0 20:52:23.228063 Frame 5: 1514 bytes on wire (12112 bits), 1514 bytes captured (12112 bits) Ethernet II, Src: Dell_97:29:ac (00:1e:4f:97:29:ac), Dst: Dell_3b:fe:70 (00:24:e8:3b:fe:70) Internet Protocol Version 4, Src: 10.6.130.38 (10.6.130.38), Dst: 10.6.130.53 (10.6.130.53) Transmission Control Protocol, Src Port: http (80), Dst Port: 48072 (48072), Seq: 1, Ack: 330, Len: 1460 Now when I see this in Wireshark: there's usual TCP handshake then the GET request shown as HTTP with preview then the next packet contains the response, but is not marked as an HTTP response--just a generic "[TCP segment of a reassembled PDU]", and is not caught by "http.response" filter. Can somebody explain why Wireshark does not recognize it? Is there something wrong with the response?

  Read the article

• Desktop PC does not power up on power button

  - by hIpPy

  When I press the power button on my desktop, it does not power up completely. Before I press the power button, I see lights on the motherboard. Everything is normal. On power button press, the fans on the cpu, graphics card and motherboard start to spin a little for a second or two and then they stop. No beeps during this process. It has been doing this for a while now but it used to start up after some trials. Once it starts up, I have NO issues at all like random shutdowns so it is not an issue with OS. Update: I left the desktop off for a few days and it started. I'm just guessing here but it seems as if the PSU (Antec TP2-550ATX) is dying out and does not have enough power now - just a guess. It's an old desktop assembled in 2005 but I have maintained it well. Update: I always keep the desktop running and I never shut it down. During updates or manual restarts, it powers up without issues. I wonder if this sheds lights on the issue. Any idea how I can narrow down the issue? ex: if I can find if the PSU is dying etc. I'd really like to fix the issue. Please help. Thanks. Below is the complete configuration. DFI LAN-Party UT NF4 Ultra-D 6/23 {6.70}, Evercool EC-VC-RE 41/47C, AMD Opteron 170 2.0GHz {1.3.2.16} 1.312V 36/41C, ThermalRight SI-120, Panaflo 120×38mm OCZ Platinum 2×1GB 200MHz 2.66V 3-3-2-7 1T XFX 7800GTX 256MB 475/1250MHz {91.31}, Zalman VF900 Cu led 41/56C WD Caviar 320GB 7200RPM 16MB SATA 3Gb/s Antec TP2-550ATX Antec P180 WinXP sp3 Logitech MX310 Razer Mantis Speed BenQ FP91G+ 19" LCD 8ms DVI Creative Audigy2 ZS {4.42} BenQ DW1640 Logitech z-5300e 5.1 280W Legend: Driver versions: {} User settings: [] Voltage: V Wattage: W Temperature: C (Celsius) min/max

  Read the article

• Why do manufacturers not show all hardware power usage?

  - by Drew

  I find it slightly more difficult to build a computer when I do not know how much power is needed for a component. When selecting a power supply for a computer, it is difficult to know how large of one to get. You don't want to go too large for cost reasons and circuit reasons, but you don't want to go too low and not be able to properly use every component. For instance, a graphics card might say "Minimum of a 500 Watt power supply. (Minimum recommended power supply with +12 Volt current rating of 30 Amps.)" But it really needs 360W (12V * 30A). So why don't they just say "Uses 360W max and xxxW peak"? Processors, I have noticed are good at reporting their power usage, but aside from processors and sometimes graphics cards, power usage is easily found. What is the power consumed by the Blu-ray / DVD drives? By the HDDs/SSDs? By the Mobo? etc. Why are these questions not easily answered when building a machine?

  Read the article

• Understanding tcptraceroute versus http response

  - by kojiro

  I'm debugging a web server that has a very high wait time before responding. The server itself is quite fast and has no load, so I strongly suspect a network problem. Basically, I make a web request: wget -O/dev/null http://hostname/ --2013-10-18 11:03:08-- http://hostname/ Resolving hostname... 10.9.211.129 Connecting to hostname|10.9.211.129|:80... connected. HTTP request sent, awaiting response... 200 OK Length: unspecified [text/html] Saving to: ‘/dev/null’ 2013-10-18 11:04:11 (88.0 KB/s) - ‘/dev/null’ saved [13641] So you see it took about a minute to give me the page, but it does give it to me with a 200 response. So I try a tcptraceroute to see what's up: $ sudo tcptraceroute hostname 80 Password: Selected device en2, address 192.168.113.74, port 54699 for outgoing packets Tracing the path to hostname (10.9.211.129) on TCP port 80 (http), 30 hops max 1 192.168.113.1 0.842 ms 2.216 ms 2.130 ms 2 10.141.12.77 0.707 ms 0.767 ms 0.738 ms 3 10.141.12.33 1.227 ms 1.012 ms 1.120 ms 4 10.141.3.107 0.372 ms 0.305 ms 0.368 ms 5 12.112.4.41 6.688 ms 6.514 ms 6.467 ms 6 cr84.phlpa.ip.att.net (12.122.107.214) 19.892 ms 18.814 ms 15.804 ms 7 cr2.phlpa.ip.att.net (12.122.107.117) 17.554 ms 15.693 ms 16.122 ms 8 cr1.wswdc.ip.att.net (12.122.4.54) 15.838 ms 15.353 ms 15.511 ms 9 cr83.wswdc.ip.att.net (12.123.10.110) 17.451 ms 15.183 ms 16.198 ms 10 12.84.5.93 9.982 ms 9.817 ms 9.784 ms 11 12.84.5.94 14.587 ms 14.301 ms 14.238 ms 12 10.141.3.209 13.870 ms 13.845 ms 13.696 ms 13 * * * … 30 * * * I tried it again with 100 hops, just to be sure – the packets never get there. So how is it that the server does respond to requests via http, even after a minute? Shouldn't all requests just die? I'm not sure how to proceed debugging why this server is slow (as opposed to why it responds at all).

  Read the article

• Time-Machine backup over SSH tunnel to NFS mount

  - by BTZ

  I've recently started using a new NAS which runs CentOS 6.2. One of the purposes of the NAS would be to serve as a backup target. Whilst I have been using Apple's Time-Machine for a while and I am very satisfied with it, I'd like to continue using it. Backing up directly to an address in my network is no hassle; all works fine. For security reasons I'd like all my traffic to go through an ssh tunnel to the NAS. This way I can avoid needing to get a VPNserver (for personal reasons). As of NFSv4 the NFS deamon is bound to port 2049, which makes it easy for me to direct all traffic through a ssh tunnel. Tunnel: ssh -f admin@ms -L 2000:localhost:2049 -N Mount: mount -t nfs -o nfsvers=4,rw,proto=tcp,sync,intr,hard,timeo=600,retrans=10,wsize=32768,rsize=32768,port=2000 localhost:/mac_backup /Volumes/backup This works fine for Finder/terminal and throughput is almost equal to direct traffic. (CPU of the NAS does ride high when I reach max bandwidth though) Now the problem: With Time-Machine I can't use the NFS mount point mounted on localhost. TM seems to try to connect to it and then give me a "OSStatus error 65". I also tried using NFSv3 (I correctly forwarded all ports) with no luck. Can anyone shed a light on this and/or give a solution?

  Read the article

• Power issues Foxconn Barebones kit

  - by alpha1

  I have a Foxconn R20D2 bought about a year and a half ago. It ran fine for a while and then around last summer it started having power issues. I chalked it up to changes in electric current due to the overwhelmed grid when people turn on their AC units, but this problem has stayed for all year, shutting off randomly, shutting off when i turn on a vacuum and similar problems. Now that its summer again, the box basically sits there all day cycling itself, and now has gotten to the point it tried to boot and after 3 seconds, fails, shuts off and tried again. I know its power related, it runs opensuse linux and there are never any shutdown logs or anything of that sort. As the weather got hotter i noticed it happening more and more, and it most often happened in the morning, i presume as people woke up and turn on the AC. The power supply is a Chennel well technology co LTD model DSL-150. 150W max output. Its an intel atom dual core, with 2 sata drives, no CD/floppy etc, recently upgrades from 2 to 4gb of ram. It runs at 104 degrees Fahrenheit all the time almost. Any way i can test the power supply or anything else to try to fix it? Im a software guy, not hardware so im at a complete loss here, thanks for all assistance you can provide! EDIT: The switch on the back that says 230 or 115 is set to 230. If im in the USA, could that be causing the problems?

  Read the article

• Two different subwoofers aren't working on my machine or my phone

  - by Philluminati

  I have speakers that come with my computer. Two small desktop speakers and a subwoofer with a base volume control on the back. It's worked for years. I was listening to Spotify on my speakers as loud they would possibly go and with the base turned up to max and suddenly the subwoofer stopped working. I've plugged the speakers into my Android HTC Desire Z handset and again, the desktop speakers play music but the subwoofer doesn't (even after fiddling with the volume control). So I figured I'd broken it. I went to Amazon and bought a replacement one. I bought this one: http://www.amazon.co.uk/dp/B002N46YD8/ref=pe_217191_31005151_dp_1 but it doesn't work either, on either my desktop nor my Android phone. I had a play with alsamixer and the LFE and center controls are switched on and the speakers are okay... but still no base. Am I unlucky enough to bought a new subwoofer which is already broken out of the box or is there something else which is wrong and I could look into please? Are there any other tests which I could perform to see if the problem is me or not?

  Read the article

• Monitoring AWS Systems Behind ElasticBeanStalk

  - by A. Avadis

  So I'm getting a company set up in the Amazon Cloud -- creating IAAS protocol/solutions/standardized implementation, etc while also being the SysAdmin for individual systems, app environments, and day-to-day uptime. One of the biggest issues I'm having is tracking various system/application logs, as well as logging/monitoring/archiving system metrics like memory usage, cpu usage, etc etc In a centralized fashion. E.g. -- Nagios + Urchin. The BIGGEST impediment to my endeavors is the following: The company application is deployed in the form of a Java *.WAR file, uploaded to an Elastic BeanStalk application environment, load balancing and auto-scaling between 3(min) and 10(max) servers, and the EC2's that run the application are fired up and disposed of ad-hoc. That is to say, I can't monitor the individual EC2's for very long because so many are being terminated then auto-provisioned/auto-scaled on the fly -- so I'd constantly be having to "monitor what I'm monitoring", and continuously remove/add EC2 machine addresses to my monitoring lists. IS there some sort of way to use monitoring tools like Zabbix or Nagios to monitor the ElasticBeanStalk, and have it automatically add on new EC2's, and remove terminated/failed EC2's from its monitoring list automatically? Furthermore, is there anything I can do with GrayLog to achieve similar results with the aggregation/centralization of my application logs from multiple EC2 instances into ONE consolidated set of logs/events? If not GrayLog, is there ANYTHING LIKE GrayLog that can automatically detect what EC2 members are being added/removed from the environment, and collect the logs from them automatically? Any and all advice or direction is appreciated. Thanks much, and cheers!!

  Read the article

• Weirdly high ping on direct ethernet connection?

  - by Antriel

  I bought new Lenovo IdeaCentre H430 pc and I'm having problem with high pings. Windows 7 with on-board realtek NIC. Fresh install, fully updated, drivers installed from included CD. When I start pinging router (direct 1Gb ethernet connection, 1 hop), pings start at <1ms (which is fine) and after a while they jump to 300-1000ms. I loaded up live ubuntu to test if the problem might be in HW. It's not, in ubuntu pings were always <1ms. I also noticed that when I start using connection somehow, pings go down to 1ms, but go back up when I stop using it (tested by accessing live camera feed on LAN). Power Options set to max performance. I disabled Interrupt Moderation on the NIC, didn't help. I tested it in the safe mode with networking, same problem there. It slows down our client-server based programs and I have no idea what's causing it. All I could google up was that disabling Interrupt Moderation would help, it didn't though. Anyone had similar problems? tl;nr: Computer is giving high pings to router when idle and normal pings when network is under load, it slows down our software significantly.

  Read the article

• Why is MySQL table_cache full but never used

  - by Jeremy Clarke

  I have been using the tuning-primer.sh script to tune my my.cnf settings. I have most things working well but the part about TABLE CACHE makes no sense: TABLE CACHE Current table_cache value = 900 tables. You have a total of 0 tables You have 900 open tables. Current table_cache hit rate is 1% , while 100% of your table cache is in use. You should probably increase your table_cache When I do SHOW STATUS; I get the following table-related numbers: Open_tables = 900 Opened_tables = 0 It seems like something is going wrong. I have some extra memory I could use on increasing the table_cache size, but my sense is that the 900 tables already available aren't doing anything, and increasing it will just waste more energy. Why might this be happening? Are there other settings that could cause all my table_cache slots to be used even though there are no hits to them? I have 150 max connections and probably no more than 4 tables per join, FWIW. Here is the tuner script output for temp tables, which I've also been tuning: TEMP TABLES Current max_heap_table_size = 90 M Current tmp_table_size = 90 M Of 11032358 temp tables, 40% were created on disk Perhaps you should increase your tmp_table_size and/or max_heap_table_size to reduce the number of disk-based temporary tables. Note! BLOB and TEXT columns are not allow in memory tables. If you are using these columns raising these values might not impact your ratio of on disk temp tables.

  Read the article

• Apache reverse proxy with VirtualHost not serving a page

  - by Mr Aleph

  I have an Apache reverse proxy set to move requests to a Tomcat Applet. The config is similar to: <VirtualHost 100.100.100.100:80> ProxyPass /AppName/App http://1.1.1.1/AppName/App ProxyPassReverse /AppName/App http://1.1.1.1/AppName/App </VirtualHost> I also have a page called summary.html that exists on 1.1.1.1 as: http://1.1.1.1/AppName/summary.html When I browse directly to it I have no problem viewing it, however if I try to get there via the reverse proxy I get a blank page. Wireshark shows me a 503, but this one is coming from the Apache reverse proxy (IP 100.100.100.100) and not the Tomcat (IP 1.1.1.1). Should I add http://1.1.1.1/AppName/ to the config? How? I tried it but I get a blank page, however this one shows on the URL bar of the browser the internal IP of the Tomcat, so, no go. Help is appreciated. Thanks. EDIT: This is the dump from Wireshark: GET /AppName/ HTTP/1.1 Host: 100.100.100.100 User-Agent: Mozilla/5.0 (Macintosh; Intel Mac OS X 10_6_8) AppleWebKit/534.52.7 (KHTML, like Gecko) Version/5.1.2 Safari/534.52.7 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Cache-Control: max-age=0 Accept-Language: en-us Accept-Encoding: gzip, deflate Connection: keep-alive HTTP/1.1 404 Not Found Date: Tue, 30 Jan 2012 09:08:51 GMT Server: Apache Content-Length: 1 Connection: close Content-Type: text/html; charset=iso-8859-1

  Read the article

• Outlook locking network connection/session?

  - by HaydnWVN

  Scenario: We have an 'automatic orders' machine sat in the corner running XP with Outlook 2003. Its job is to check for new emails on a specific account, when it encounters one it checks the e-mail body for specific wording to determine which customer it is from (using a macro), then it checks the attachment for specific order codes before parsing the attachment to create a .csv file (which is then e-mailed onto one of the sales team) before importing the .csv into our bespoke ERP/Sales Order system to create an order. Problem: Periodically the machine will have symptoms of a lost network connection (unable to connect to any network source). Sometimes after several days, sometimes over a week. Volume of emails/orders processed does not seem to be linked. Additional info: The machines .pst is stored on a mapped network location. The .csv created is stored on a mapped network location. This is a workgroup, not a domain. All network drives are Samba shares from an Ubuntu fileserver. Our bespoke system runs from a database (MySQL) Ubuntu server. Our troubleshooting so far: I have switched machines (previous was Win2000) with the same symptoms. Restarting the machine FIXES the problem. Closing Outlook and then end tasking an Outlook.exe background process FIXES the problem. If you close Outlook, without end taking the background process, outlook will not reopen (saying it cannot find the pst file & it will not open any network location). Does Outlook have some kind of 'max session' linking it to network activity that is not closing after a mail request? Could Auto-archive be causing this? Is there a tool to check/display what each outlook.exe process is doing? Have not found many ways to troubleshoot this yet, as it is so infrequent...

  Read the article

• Important hardware components to avoid bottlenecks/improve speed on a laptop?

  - by joelhaus

  Looking for a powerful general use (including web development) laptop running Windows. Price points seem to be all over the place. Many less powerful machines are priced much higher than machines with better specs. How does one navigate this market? Are there any unpublished/under-publicized specs/bottlenecks you look for? Understanding that hardware improves over time, is there an efficient ratio that can be used (or something similar, like Windows Experience Index?) which will indicate how powerful a system is? Thanks in advance! P.S. Here is an example from a laptop released on September 17, 2010. Can anyone pick apart these specs? Is there missing information you would be looking for? OS: Win 7 Display: 16.4" LED backlit Processor: Intel Core i7-740QM, 6MB L3 Cache RAM: 6GB DDR3 1333MHz (8GB max.) Graphics: NVIDIA GeForce GT 425M (1 GB of dedicated DDR3) HDD: 500GB 7200RPM SATA Hard Drive Removable Disc: Blue-ray with DVD±R/RW Misc: webcam/mic/speakers/bluetooth (via Sony Vaio VPC-F137FX/B)

  Read the article

• Nginx map module 301 redirecting

  - by Reinier Korth

  I've rebuild my website in Ruby on Rails and now I want to 301 redirect a lot of old urls using Nginx's http://wiki.nginx.org/HttpMapModule For some reason I can't get it to work. It works fine without the rewrite ^ $new permanent; line. Does anyone see what I'm missing? This my nginx.conf: server { server_name example.com; return 301 $scheme://www.example.com$request_uri; } # 301 redirect list map $uri $new { /test123 http://www.example.com/test123; /bla http://www.example.com/bladiebla; } server { server_name www.example.com; rewrite ^ $new permanent; root example/public; location ^~ /assets/ { gzip_static on; expires max; add_header Cache-Control public; } try_files $uri/index.html $uri @unicorn; location @unicorn { proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $http_host; proxy_redirect off; proxy_pass http://unicorn-<%= application %>; } error_page 500 502 503 504 /500.html; client_max_body_size 4G; keepalive_timeout 10; }

  Read the article

• Why is IIS 7.5 seeing some requests as HTTP/1.0?

  - by Zhaph - Ben Duguid

  While trying to work out why Static File Compression wasn't working on one of our IIS servers, the error was coming back as "NO_COMPRESSION_10" which translates to: Server not configured to compress 1.0 requests Looking at the requests in Fiddler, I can see that I'm requesting HTTP 1.1, but everything is being sent back as HTTP 1.0: Request (from chrome, captured via Fiddler): GET /css/reset.css HTTP/1.1 Host: [-----].com Connection: keep-alive Cache-Control: max-age=0 If-Modified-Since: Tue, 16 Oct 2012 15:04:34 GMT User-Agent: Mozilla/5.0 (Windows NT 6.1; WOW64) AppleWebKit/537.11 (KHTML, like Gecko) Chrome/23.0.1271.95 Safari/537.11 Accept: text/css,*/*;q=0.1 Referer: http://[-----].com/ Accept-Encoding: gzip,deflate,sdch Accept-Language: en-GB,en;q=0.8,en-US;q=0.6 Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.3 Response from IIS: HTTP/1.0 200 OK Cache-Control: no-cache, no-store Pragma: no-cache Content-Type: text/html; charset=utf-8 Expires: -1 Server: Microsoft-IIS/7.5 X-AspNet-Version: 4.0.30319 X-Powered-By: ASP.NET Date: Tue, 11 Dec 2012 11:57:03 GMT Connection: close Content-Length: 108837 Other servers with the same host that I'm running this site on all respond with HTTP/1.1. How can I persuade IIS to respond with HTTP/1.1 rather than HTTP/1.0? Edit to add: Digging deeper, I can see that some responses from the server are indeed being returned compressed, so I guess really I'm trying to work out why talking to this particular server from our office seems to result in it seeing 1.0 requests, while other servers at the same co-loc don't?

  Read the article

• plesk: how to configure reverse proxy rules properly?

  - by rvdb

  I'm trying to configure reverse proxy rules in vhost.conf. I have Apache-2.2.8 on Ubuntu-8.04, monitored by Plesk-10.4.4. What I'm trying to achieve is defining a reverse proxy rule that defers all traffic to -say- http://mydomain/tomcat/ to the Tomcat server running on port 8080. I have mod_rewrite and mod_proxy loaded in Apache. As far as I understand mod_proxy docs, entering following rules in /var/www/vhosts/mydomain/conf/vhost.conf should work: <Proxy *> Order deny,allow Allow from all </Proxy> ProxyRequests off RewriteRule ^/tomcat/(.*)$ http://mydomain:8080/$1 [P] Yet, I am getting a HTTP 500: internal server error when requesting above URL. (Note: I decided to use a rewrite rule in order to at least get some information logged.) I have made mod_rewrite log extensively, and find following entries in the logs [note: due to a limitation of max. 2 URLs in posts of new users, I have modified all following URLs so that they only contain 1 slash after http:. In case you're suspecting typos: this was done on purpose): 81.241.230.23 - - [19/Mar/2012:16:42:59 +0100] [mydomain/sid#b06ab8][rid#1024af8/initial] (2) init rewrite engine with requested uri /tomcat/testApp/ 81.241.230.23 - - [19/Mar/2012:16:42:59 +0100] [mydomain/sid#b06ab8][rid#1024af8/initial] (3) applying pattern '^/tomcat/(.*)$' to uri '/tomcat/testApp/' 81.241.230.23 - - [19/Mar/2012:16:42:59 +0100] [mydomain/sid#b06ab8][rid#1024af8/initial] (2) rewrite '/tomcat/testApp/' - 'http:/mydomain:8080/testApp/' 81.241.230.23 - - [19/Mar/2012:16:42:59 +0100] [mydomain/sid#b06ab8][rid#1024af8/initial] (2) forcing proxy-throughput with http:/mydomain:8080/testApp/ 81.241.230.23 - - [19/Mar/2012:16:42:59 +0100] [mydomain/sid#b06ab8][rid#1024af8/initial] (1) go-ahead with proxy request proxy:http:/mydomain:8080/testApp/ [OK] This suggests that the rewrite and proxy part is processed ok; still the proxied request produces a 500 error. Yet: Addressing the testApp directly via http:/mydomain:8080/testApp does work. The same setup does work on my local computer. Is there something else (Plesk-related, perhaps?) I should configure? Many thanks for any pointers! Ron

  Read the article

< Previous Page | 187 188 189 190 191 192 193 194 195 196 197 198  | Next Page >