Search Results

Search found 19018 results on 761 pages for 'indicator network'.

Page 192/761 | < Previous Page | 188 189 190 191 192 193 194 195 196 197 198 199  | Next Page >

• Atheros Wireless card shows up as two different models?

  - by geermc4

  Hi I've been fighting these wireless drivers for a few days and just recently i noticed that the model the Wireless controller appears in lspci is different sometimes. This is the data i have after installing Ubuntu Server 64 bit ~# lspci -k .... 04:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) Subsystem: AzureWave Device 1d89 Kernel driver in use: ath9k Kernel modules: ath9k ran some updates, restarted, all was good, all though it did say that linux-headers-server linux-image-server linux-server where beeing kept back. After that i installed ubuntu-desktop (aptitude install ubuntu-desktop --without-recommends) restarted and not only is the wireless not working anymore, but the hardware is listed as a different card ~# lspci -k .... 04:00.0 Ethernet controller: Atheros Communications Inc. AR5008 Wireless Network Adapter (rev 01) has no available drivers for it, still i tried to modprobe ath9k, they show up in lsmod as loaded, but still iw list shows nothing. this is what it looked like before the ubuntu-desktop instalation Wiphy phy0 Band 1: Capabilities: 0x11ce HT20/HT40 SM Power Save disabled RX HT40 SGI TX STBC RX STBC 1-stream Max AMSDU length: 3839 bytes DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 8 usec (0x06) HT TX/RX MCS rate indexes supported: 0-7 Frequencies: * 2412 MHz [1] (14.0 dBm) * 2417 MHz [2] (15.0 dBm) * 2422 MHz [3] (15.0 dBm) * 2427 MHz [4] (15.0 dBm) * 2432 MHz [5] (15.0 dBm) * 2437 MHz [6] (15.0 dBm) * 2442 MHz [7] (15.0 dBm) * 2447 MHz [8] (15.0 dBm) * 2452 MHz [9] (15.0 dBm) * 2457 MHz [10] (15.0 dBm) * 2462 MHz [11] (15.0 dBm) * 2467 MHz [12] (15.0 dBm) (passive scanning) * 2472 MHz [13] (14.0 dBm) (passive scanning) * 2484 MHz [14] (17.0 dBm) (passive scanning) Bitrates (non-HT): * 1.0 Mbps * 2.0 Mbps (short preamble supported) * 5.5 Mbps (short preamble supported) * 11.0 Mbps (short preamble supported) * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps max # scan SSIDs: 4 max scan IEs length: 2257 bytes Coverage class: 0 (up to 0m) Supported Ciphers: * WEP40 (00-0f-ac:1) * WEP104 (00-0f-ac:5) * TKIP (00-0f-ac:2) * CCMP (00-0f-ac:4) * CMAC (00-0f-ac:6) Available Antennas: TX 0x1 RX 0x3 Configured Antennas: TX 0x1 RX 0x3 Supported interface modes: * IBSS * managed * AP * AP/VLAN * WDS * monitor * mesh point * P2P-client * P2P-GO software interface modes (can always be added): * AP/VLAN * monitor interface combinations are not supported Supported commands: * new_interface * set_interface * new_key * new_beacon * new_station * new_mpath * set_mesh_params * set_bss * authenticate * associate * deauthenticate * disassociate * join_ibss * join_mesh * remain_on_channel * set_tx_bitrate_mask * action * frame_wait_cancel * set_wiphy_netns * set_channel * set_wds_peer * connect * disconnect Supported TX frame types: * IBSS: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * managed: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * AP: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * AP/VLAN: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * mesh point: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * P2P-client: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * P2P-GO: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 Supported RX frame types: * IBSS: 0x00d0 * managed: 0x0040 0x00d0 * AP: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 * AP/VLAN: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 * mesh point: 0x00b0 0x00c0 0x00d0 * P2P-client: 0x0040 0x00d0 * P2P-GO: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 Device supports RSN-IBSS. What's with the hardware change? If it has 2, how can i make the AR9285 always load and disable AR5008, or, is it the same and it's just showing it different? :| Oh and I've tried this on Ubuntu 10.04 server, xubuntu 12.04, ubuntu 12.04 desktop and server. Thanks in advanced. -- Here's some more info, i have it setup in 2 hard drives, 1 works and the other one i'm using to figure it out The one that works... # lshw -class network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 06 serial: 54:04:a6:a3:3b:96 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw ip=192.168.2.147 latency=0 link=yes multicast=yes port=MII speed=1Gbit/s resources: irq:43 ioport:e000(size=256) memory:d0004000-d0004fff memory:d0000000-d0003fff *-network description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 logical name: wlan0 version: 01 serial: 74:2f:68:4a:26:73 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-18-generic-pae firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:fea00000-fea0ffff Here's where it doesn't # lshw -class network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 06 serial: 54:04:a6:a3:3b:96 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw ip=192.168.2.160 latency=0 link=yes multicast=yes port=MII speed=1Gbit/s resources: irq:43 ioport:e000(size=256) memory:d0004000-d0004fff memory:d0000000-d0003fff *-network UNCLAIMED description: Ethernet controller product: AR5008 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:fea00000-fea0ffff Update I've noticed that if i blacklist the ath9k and ath9k_common modules lspci gives me the AR9285, but then I need to modprobe ath9k for it to work, does this make any sense? If so, why?

  Read the article

• WDS 2008 R2 DHCP Error

  - by scampbell

  Im having a problem where I get the error 'An error occurred while obtaining an IP address from the DHCP server. Please check to ensure that there is an operational DHCP server on this network segment' when booting from a standard WDS boot.wim image taken from a Windows 7 DVD. I am using Server 2008 R2 and am adding the drivers to the boot using WDS, but also have the problem if the drivers are injected beforehand using DISM. When the error occurs I can shift + F10 and IPCONFIG and see it HAS picked up an internal IP from DHCP. Seems maybe it is timing out before it gets the IP? DHCP server is not on the WDS box but is in the same subnet. As per some fixes I have read I enabled RSTP on my switches but that didnt help. I have included the end of setupact.log to see if any of you have any ideas. Seems to be failing but as I say, the network IS initialized as I can see the internal IP assigned by DHCP when running IPCONFIG. I dont suppose theres any way of increasing the timeout? Thanks. 2011-04-11 17:26:31, Info [0x0b0022] WDS StartNetworking: Trying to start networking. 2011-04-11 17:26:31, Info WDS Network service dhcp not running or could not be queried: 264d00 1 1 2011-04-11 17:26:31, Info WDS Network service lmhosts not running or could not be queried: 264e18 1 1 2011-04-11 17:26:31, Info WDS Network service lanmanworkstation not running or could not be queried: 264d00 1 1 2011-04-11 17:26:31, Info WDS Network service bfe not running or could not be queried: 264e18 1 1 2011-04-11 17:26:31, Info WDS Network service ikeext not running or could not be queried: 264d00 1 1 2011-04-11 17:26:31, Info WDS Network service mpssvc not running or could not be queried: 264e18 1 1 2011-04-11 17:27:24, Info WDS Installing device pci\ven_14e4&dev_1691&subsys_04aa1028 X:\WINDOWS\INF\oem37.inf succeeded 2011-04-11 17:27:25, Info WDS No computer name specified, generating a random name. 2011-04-11 17:27:25, Info WDS Renaming computer to MININT-VN2P876. 2011-04-11 17:27:25, Info WDS Acquired profiling mutex 2011-04-11 17:27:25, Info WDS Service winmgmt disable: 0x00000000 2011-04-11 17:27:25, Info WDS Service winmgmt stop: 0x00000000 2011-04-11 17:27:25, Info WDS Service winmgmt enable: 0x00000000 2011-04-11 17:27:25, Info WDS Released profiling mutex 2011-04-11 17:27:25, Info WDS Acquired profiling mutex 2011-04-11 17:27:25, Info WDS Install MS_MSCLIENT: 0x0004a020 2011-04-11 17:27:25, Info WDS Install MS_NETBIOS: 0x0004a020 2011-04-11 17:27:25, Info WDS Install MS_SMB: 0x0004a020 2011-04-11 17:27:25, Info WDS Install MS_TCPIP6: 0x0004a020 2011-04-11 17:27:26, Info WDS Install MS_TCPIP: 0x0004a020 2011-04-11 17:27:26, Info WDS Service dhcp start: 0x00000000 2011-04-11 17:27:26, Info WDS Service lmhosts start: 0x00000000 2011-04-11 17:27:26, Info WDS Service ikeext start: 0x00000000 2011-04-11 17:27:26, Info WDS Service mpssvc start: 0x00000000 2011-04-11 17:27:26, Info WDS Released profiling mutex 2011-04-11 17:27:26, Info WDS Spent 967ms installing network components 2011-04-11 17:27:28, Info WDS Spent 2247ms installing network drivers 2011-04-11 17:27:38, Info WDS QueryAdapterStatus: no operational adapters found. 2011-04-11 17:27:38, Info WDS Spent 10140ms confirming network initialization; status 0x80004005 2011-04-11 17:27:38, Info WDS WaitForNetworkToInitialize failed; ignoring error 2011-04-11 17:27:38, Info WDS GetNetworkingInfo: WpeNetworkStatus returned [0x0]. Flags set: 2011-04-11 17:27:38, Error [0x0b003f] WDS StartNetworking: Failed to start networking. Error code [0x800704C6].[gle=0x000000cb] 2011-04-11 17:27:38, Info [0x0640ae] IBSLIB PublishMessage: Publishing message [WdsClient: An error occurred while obtaining an IP address from the DHCP server. Please check to ensure that there is an operational DHCP server on this network segment.]

  Read the article

• Cisco ASA: How to route PPPoE-assigned subnet?

  - by Martijn Heemels

  We've just received a fiber uplink, and I'm trying to configure our Cisco ASA 5505 to properly use it. The provider requires us to connect via PPPoE, and I managed to configure the ASA as a PPPoE client and establish a connection. The ASA is assigned an IP address by PPPoE, and I can ping out from the ASA to the internet, but I should have access to an entire /28 subnet. I can't figure out how to get that subnet configured on the ASA, so that I can route or NAT the available public addresses to various internal hosts. My assigned range is: 188.xx.xx.176/28 The address I get via PPPoE is 188.xx.xx.177/32, which according to our provider is our Default Gateway address. They claim the subnet is correctly routed to us on their side. How does the ASA know which range it is responsible for on the Fiber interface? How do I use the addresses from my range? To clarify my config; The ASA is currently configured to default-route to our ADSL uplink on port Ethernet0/0 (interface vlan2, nicknamed Outside). The fiber is connected to port Ethernet0/2 (interface vlan50, nicknamed Fiber) so I can configure and test it before making it the default route. Once I'm clear on how to set it all up, I'll fully replace the Outside interface with Fiber. My config (rather long): : Saved : ASA Version 8.3(2)4 ! hostname gw domain-name example.com enable password ****** encrypted passwd ****** encrypted names name 10.10.1.0 Inside-dhcp-network description Desktops and clients that receive their IP via DHCP name 10.10.0.208 svn.example.com description Subversion server name 10.10.0.205 marvin.example.com description LAMP development server name 10.10.0.206 dns.example.com description DNS, DHCP, NTP ! interface Vlan2 description Old ADSL WAN connection nameif outside security-level 0 ip address 192.168.1.2 255.255.255.252 ! interface Vlan10 description LAN vlan 10 Regular LAN traffic nameif inside security-level 100 ip address 10.10.0.254 255.255.0.0 ! interface Vlan11 description LAN vlan 11 Lab/test traffic nameif lab security-level 90 ip address 10.11.0.254 255.255.0.0 ! interface Vlan20 description LAN vlan 20 ISCSI traffic nameif iscsi security-level 100 ip address 10.20.0.254 255.255.0.0 ! interface Vlan30 description LAN vlan 30 DMZ traffic nameif dmz security-level 50 ip address 10.30.0.254 255.255.0.0 ! interface Vlan40 description LAN vlan 40 Guests access to the internet nameif guests security-level 50 ip address 10.40.0.254 255.255.0.0 ! interface Vlan50 description New WAN Corporate Internet over fiber nameif fiber security-level 0 pppoe client vpdn group KPN ip address pppoe ! interface Ethernet0/0 switchport access vlan 2 speed 100 duplex full ! interface Ethernet0/1 switchport trunk allowed vlan 10,11,30,40 switchport trunk native vlan 10 switchport mode trunk ! interface Ethernet0/2 switchport access vlan 50 speed 100 duplex full ! interface Ethernet0/3 shutdown ! interface Ethernet0/4 shutdown ! interface Ethernet0/5 switchport access vlan 20 ! interface Ethernet0/6 shutdown ! interface Ethernet0/7 shutdown ! boot system disk0:/asa832-4-k8.bin ftp mode passive clock timezone CEST 1 clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00 dns domain-lookup inside dns server-group DefaultDNS name-server dns.example.com domain-name example.com same-security-traffic permit inter-interface same-security-traffic permit intra-interface object network inside-net subnet 10.10.0.0 255.255.0.0 object network svn.example.com host 10.10.0.208 object network marvin.example.com host 10.10.0.205 object network lab-net subnet 10.11.0.0 255.255.0.0 object network dmz-net subnet 10.30.0.0 255.255.0.0 object network guests-net subnet 10.40.0.0 255.255.0.0 object network dhcp-subnet subnet 10.10.1.0 255.255.255.0 description DHCP assigned addresses on Vlan 10 object network Inside-vpnpool description Pool of assignable addresses for VPN clients object network vpn-subnet subnet 10.10.3.0 255.255.255.0 description Address pool assignable to VPN clients object network dns.example.com host 10.10.0.206 description DNS, DHCP, NTP object-group service iscsi tcp description iscsi storage traffic port-object eq 3260 access-list outside_access_in remark Allow access from outside to HTTP on svn. access-list outside_access_in extended permit tcp any object svn.example.com eq www access-list Insiders!_splitTunnelAcl standard permit 10.10.0.0 255.255.0.0 access-list iscsi_access_in remark Prevent disruption of iscsi traffic from outside the iscsi vlan. access-list iscsi_access_in extended deny tcp any interface iscsi object-group iscsi log warnings ! snmp-map DenyV1 deny version 1 ! pager lines 24 logging enable logging timestamp logging asdm-buffer-size 512 logging monitor warnings logging buffered warnings logging history critical logging asdm errors logging flash-bufferwrap logging flash-minimum-free 4000 logging flash-maximum-allocation 2000 mtu outside 1500 mtu inside 1500 mtu lab 1500 mtu iscsi 9000 mtu dmz 1500 mtu guests 1500 mtu fiber 1492 ip local pool DHCP_VPN 10.10.3.1-10.10.3.20 mask 255.255.0.0 ip verify reverse-path interface outside no failover icmp unreachable rate-limit 10 burst-size 5 asdm image disk0:/asdm-635.bin asdm history enable arp timeout 14400 nat (inside,outside) source static any any destination static vpn-subnet vpn-subnet ! object network inside-net nat (inside,outside) dynamic interface object network svn.example.com nat (inside,outside) static interface service tcp www www object network lab-net nat (lab,outside) dynamic interface object network dmz-net nat (dmz,outside) dynamic interface object network guests-net nat (guests,outside) dynamic interface access-group outside_access_in in interface outside access-group iscsi_access_in in interface iscsi route outside 0.0.0.0 0.0.0.0 192.168.1.1 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy aaa-server SBS2003 protocol radius aaa-server SBS2003 (inside) host 10.10.0.204 timeout 5 key ***** aaa authentication enable console SBS2003 LOCAL aaa authentication ssh console SBS2003 LOCAL aaa authentication telnet console SBS2003 LOCAL http server enable http 10.10.0.0 255.255.0.0 inside snmp-server host inside 10.10.0.207 community ***** version 2c snmp-server location Server room snmp-server contact [email protected] snmp-server community ***** snmp-server enable traps snmp authentication linkup linkdown coldstart snmp-server enable traps syslog crypto ipsec transform-set TRANS_ESP_AES-256_SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set TRANS_ESP_AES-256_SHA mode transport crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map outside_dyn_map 20 set pfs group5 crypto dynamic-map outside_dyn_map 20 set transform-set TRANS_ESP_AES-256_SHA crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5 crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 1 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 telnet 10.10.0.0 255.255.0.0 inside telnet timeout 5 ssh scopy enable ssh 10.10.0.0 255.255.0.0 inside ssh timeout 5 ssh version 2 console timeout 30 management-access inside vpdn group KPN request dialout pppoe vpdn group KPN localname INSIDERS vpdn group KPN ppp authentication pap vpdn username INSIDERS password ***** store-local dhcpd address 10.40.1.0-10.40.1.100 guests dhcpd dns 8.8.8.8 8.8.4.4 interface guests dhcpd update dns interface guests dhcpd enable guests ! threat-detection basic-threat threat-detection scanning-threat threat-detection statistics host number-of-rate 2 threat-detection statistics port number-of-rate 3 threat-detection statistics protocol number-of-rate 3 threat-detection statistics access-list threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200 ntp server dns.example.com source inside prefer webvpn group-policy DfltGrpPolicy attributes vpn-tunnel-protocol IPSec l2tp-ipsec group-policy Insiders! internal group-policy Insiders! attributes wins-server value 10.10.0.205 dns-server value 10.10.0.206 vpn-tunnel-protocol IPSec l2tp-ipsec split-tunnel-policy tunnelspecified split-tunnel-network-list value Insiders!_splitTunnelAcl default-domain value example.com username martijn password ****** encrypted privilege 15 username marcel password ****** encrypted privilege 15 tunnel-group DefaultRAGroup ipsec-attributes pre-shared-key ***** tunnel-group Insiders! type remote-access tunnel-group Insiders! general-attributes address-pool DHCP_VPN authentication-server-group SBS2003 LOCAL default-group-policy Insiders! tunnel-group Insiders! ipsec-attributes pre-shared-key ***** ! class-map global-class match default-inspection-traffic class-map type inspect http match-all asdm_medium_security_methods match not request method head match not request method post match not request method get ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map type inspect http http_inspection_policy parameters protocol-violation action drop-connection policy-map global-policy class global-class inspect dns inspect esmtp inspect ftp inspect h323 h225 inspect h323 ras inspect http inspect icmp inspect icmp error inspect mgcp inspect netbios inspect pptp inspect rtsp inspect snmp DenyV1 ! service-policy global-policy global smtp-server 123.123.123.123 prompt hostname context call-home profile CiscoTAC-1 no active destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address email [email protected] destination transport-method http subscribe-to-alert-group diagnostic subscribe-to-alert-group environment subscribe-to-alert-group inventory periodic monthly subscribe-to-alert-group configuration periodic monthly subscribe-to-alert-group telemetry periodic daily hpm topN enable Cryptochecksum:a76bbcf8b19019771c6d3eeecb95c1ca : end asdm image disk0:/asdm-635.bin asdm location svn.example.com 255.255.255.255 inside asdm location marvin.example.com 255.255.255.255 inside asdm location dns.example.com 255.255.255.255 inside asdm history enable

  Read the article

• Network authentication + roaming home directory - which technology should I look into using?

  - by Brian

  I'm looking into software which provides a user with a single identity across multiple computers. That is, a user should have the same permissions on each computer, and the user should have access to all of his or her files (roaming home directory) on each computer. There seem to be many solutions for this general idea, but I'm trying to determine the best one for me. Here are some details along with requirements: The network of machines are Amazon EC2 instances running Ubuntu. We access the machines with SSH. Some machines on this LAN may have different uses, but I am only discussing machines for a certain use (running a multi-tenancy platform). The system will not necessarily have a constant amount of machines. We may have to permanently or temporarily alter the amount of machines running. This is the the reason why I'm looking into centralized authentication/storage. The implementation of this effect should be a secure one. We're unsure if users will have direct shell access, but their software will potentially be running (under restricted Linux user names, of course) on our systems, which is as good as direct shell access. Let's assume that their software could potentially be malicious for the sake of security. I have heard of several technologies/combinations to achieve my goal, but I'm unsure of the ramifications of each. An older ServerFault post recommended NFS & NIS, though the combination has security problems according to this old article by Symantec. The article suggests moving to NIS+, but, as it is old, this Wikipedia article has cited statements suggesting a trending away from NIS+ by Sun. The recommended replacement is another thing I have heard of... LDAP. It looks like LDAP can be used to save user information in a centralized location on a network. NFS would still need to be used to cover the 'roaming home folder' requirement, but I see references of them being used together. Since the Symantec article pointed out security problems in both NIS and NFS, is there software to replace NFS, or should I heed that article's suggestions for locking it down? I'm tending toward LDAP because another fundamental piece of our architecture, RabbitMQ, has a authentication/authorization plugin for LDAP. RabbitMQ will be accessible in a restricted manner to users on the system, so I would like to tie the security systems together if possible. Kerberos is another secure authentication protocol that I have heard of. I learned a bit about it some years ago in a cryptography class but don't remember much about it. I have seen suggestions online that it can be combined with LDAP in several ways. Is this necessary? What are the security risks of LDAP without Kerberos? I also remember Kerberos being used in another piece of software developed by Carnegie Mellon University... Andrew File System, or AFS. OpenAFS is available for use, though its setup seems a bit complicated. At my university, AFS provides both requirements... I can log in to any machine, and my "AFS folder" is always available (at least when I acquire an AFS token). Along with suggestions for which path I should look into, does anybody have any guides which were particularly helpful? As the bold text pointed out, LDAP looks to be the best choice, but I'm particularly interested in the implementation details (Keberos? NFS?) with respect to security.

  Read the article

• MacBook Pro 10.6 losing dns service, network connection still functional if you know the ip address.

  - by Vincent

  MacBook pro connected to a wireless network (not sure about wired) I lose DNS. I still have a functioning connection and as long as I know the ip address of the website, server... for example skype works, ssh name@ipaddress, .... Things can be working properly and then just quit, Once I was im via skype and lost dns skype continued to work. This has happened in multiple locations on private and public networks. What does not work/fix it: Resetting router changing dns server on computer or router connecting to another network removing the airport interface and adding it back flushing dns The only solution seems to be a restart. A solution to this would be great, but any ideas of this to try would be great. Even a sure way to reproduce this would be useful. Maybe related question: But this is most definitely not true for me. "if I refresh enough -- 3 to 4 times --, it will usually pull up the site. " Here are some tests from terminal. Basically this confirms dns in not functioning vmd17:~ vmd$ ping google.com ping: cannot resolve google.com: Unknown host Trace route to google dns, This works vmd17:~ vmd$ /usr/sbin/traceroute -n -w 2 -q 2 -m 30 8.8.8.8 traceroute to 8.8.8.8 (8.8.8.8), 30 hops max, 52 byte packets 1 192.168.1.1 5.195 ms 2.519 ms 2 67.172.136.1 31.881 ms 9.177 ms 3 68.85.107.121 12.168 ms 10.003 ms 4 68.86.103.41 12.021 ms 9.594 ms 5 68.86.91.1 16.712 ms 12.837 ms 6 68.86.86.210 29.951 ms 25.826 ms 7 68.86.87.218 29.554 ms 42.894 ms 8 75.149.231.70 68.271 ms 68.362 ms 9 72.14.233.77 141.178 ms 72.14.233.85 82.553 ms 10 72.14.238.243 83.381 ms 82.811 ms 11 72.14.232.213 194.387 ms 72.14.232.215 84.837 ms 12 209.85.253.145 100.294 ms * 13 8.8.8.8 101.689 ms 89.694 ms 208.67.222.22 is the ip address of opendns dns server vmd17:~ vmd$ dig @208.67.222.222 8.8.8.8 ; <<>> DiG 9.6.0-APPLE-P2 <<>> @208.67.222.222 8.8.8.8 ; (1 server found) ;; global options: +cmd ;; connection timed out; no servers could be reached vmd17:~ vmd$ dig @208.67.222.222 gogle.com vmd17:~ vmd$ dig @208.67.222.222 google.com ; <<>> DiG 9.6.0-APPLE-P2 <<>> @208.67.222.222 google.com ; (1 server found) ;; global options: +cmd ;; connection timed out; no servers could be reached vmd17:~ vmd$ dig @8.8.8.8 google.com ; <<>> DiG 9.6.0-APPLE-P2 <<>> @8.8.8.8 google.com ; (1 server found) ;; global options: +cmd ;; connection timed out; no servers could be reached

  Read the article

• Network update solutions for a company of ~20 (5 local, 15 remote)?

  - by Margaret

  Hi all This is probably going to be a bit up in the air, because we're still in the "reaching towards solutions" phase, but I figured I'd see what you guys had to say. Plus I honestly know very little about systems and what is good and bad pratice. My organisation has always more or less worked on the concept of local machines; since it primarily employed contractors who were working from home, each of those people was largely responsible for their own machine and backup procedures and the like. We're now expanding, though we're still reasonably small (we're up to about 20 staff members). Most people still work remotely, but we have a central office where about five people are working. But we're getting large enough that we're starting to think it would be a good idea to have a central file server, and things like that - if someone gets hit by a bus, we want someone else to know where to look for the files to continue their work. A lot of the people who work for us remotely work on projects for other companies as well, so I don't want to force them to log in to our server whenever they're on a network. But I do want to make connection to be as painless as possible to do so, to improve utilisation. The other thing is that we're getting more people who would like to remote into the office server and do their work there. Our current remote connection application is an SSH install that allows people access to the network; the problem is, it's a black box to me, and I've never understood how to even connect to it (despite supposedly being de facto sysadmin). Thus far I've been able to bounce questions about how to get it working to the guy who does know it well, but he's leaving the company soon. So we probably need a solution for this that I actually understand. We were knocking around the idea of implementing a VPN with some form of remote desktop, and someone mentioned that this was largely a matter of purchasing a router capable of it; I'm not sure of the truth of that statement. This is what we have in the office: Two shiny new i7 servers, each running Windows Server 2008. Precise eventual layout is still being debated, a little, but the current suggestion is that one is primary database crunching, while the other is a warm backup of the databases, along with running Reporting Services. They currently have SQL Server 2008 installed on them, which is being connected to via the 'sa' account. We're hoping to make each person use their own account (preferably one tied to the 'central' password we set up, so we can use Windows Authentication). An older server, running XP Pro, that we are currently using as a test bed for a project that requires access to older versions of software. This machine is also being used to take backups, but I'm thinking of moving that functionality elsewhere. A spare desktop from a guy who left the company (XP Pro). We're thinking of bumping up the hard disk space and using it as the magical file server that's going to solve one particular everything. Assorted desktops, laptops, etc, at least one for each person in the office (mix of Win XP and Win 7; occasionally a person who normally works remotely might drop in to the office and bring a laptop bearing Vista, but it's pretty rare). All are set up as local user accounts at the moment; I don't know if it's the best arrangement. Purchasing more hardware is not a big problem, but we figure we might as well make use of what we've got first. Is Active Directory a big magic wand that's going to solve all the world's problems? Is there some other arrangement we should be looking to instead?

  Read the article

• Networking issues with Linux server (CentOS 5.3)

  - by sxanness

  I have a Linux server hosting our bug tracking software (CentOS 5.2 Kernel 2.6.18-128.4.1.el5) that I have having some strange network problems with. The machine is configured with two NICS, one for the public interface and the other for our server back end network. The problem is that after doing a service network restart I can ping the public interface and it sends anywhere from 200-500 ICMP packets and then all of a sudden I start getting a request timed out error. Strange but as soon as I connect to the private interface the ping starts working again to the public interface. I clearly have a routing issue somewhere. I have a Juniper Router with the following configuration. Interface 0/0 -- Connect subnet to the ISP at our co-location Interface 0/2 -- For our DRAC network Interface 0/3 -- The Server-backend network (plugs directly into a switch that feeds to all the NICs that are on the 10.3.20.x network. Interface 0/4 -- Plugs directly into another switch that feeds our public interfaces, that interface as all the gateways from our public ip rangs as secondary IP addresses. I hope that someone can ask the right questions that can lead me to check things and figure out what is going on. Has anyone had similar problems and what kind of things should I be checking? Routing issue or something even more complicated? [root@fogbugz ~]# cat /etc/sysconfig/network-scripts/ifcfg-eth0 # Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ DEVICE=eth0 BOOTPROTO=static IPADDR=72.249.134.98 NETMASK=255.255.255.248 BROADCAST=72.249.134.103 HWADDR=00:16:3E:AA:BB:EE ONBOOT=yes [root@fogbugz ~]# cat /etc/sysconfig/network-scripts/ifcfg-eth1 # Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ DEVICE=eth1 BOOTPROTO=static BROADCAST=10.3.20.255 HWADDR=00:17:3E:AA:BB:EE IPADDR=10.3.20.25 NETMASK=255.255.255.0 NETWORK=10.3.20.0 ONBOOT=yes [root@fogbugz ~]# cat /etc/sysconfig/network NETWORKING=yes NETWORKING_IPV6=no HOSTNAME=fogbugz.dfw.hisg-it.net GATEWAY=72.249.134.97 [root@fogbugz ~]# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 72.249.134.96 0.0.0.0 255.255.255.248 U 0 0 0 eth0 10.3.20.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 10.0.0.0 10.3.20.1 255.0.0.0 UG 0 0 0 eth1 0.0.0.0 72.249.134.97 0.0.0.0 UG 0 0 0 eth0

  Read the article

• Networking issues with Linux server (CentOS 5.3)

  - by sxanness

  I have a Linux server hosting our bug tracking software (CentOS 5.2 Kernel 2.6.18-128.4.1.el5) that I have having some strange network problems with. The machine is configured with two NICS, one for the public interface and the other for our server back end network. The problem is that after doing a service network restart I can ping the public interface and it sends anywhere from 200-500 ICMP packets and then all of a sudden I start getting a request timed out error. Strange but as soon as I connect to the private interface the ping starts working again to the public interface. I clearly have a routing issue somewhere. I have a Juniper Router with the following configuration. Interface 0/0 -- Connect subnet to the ISP at our co-location Interface 0/2 -- For our DRAC network Interface 0/3 -- The Server-backend network (plugs directly into a switch that feeds to all the NICs that are on the 10.3.20.x network. Interface 0/4 -- Plugs directly into another switch that feeds our public interfaces, that interface as all the gateways from our public ip rangs as secondary IP addresses. I hope that someone can ask the right questions that can lead me to check things and figure out what is going on. Has anyone had similar problems and what kind of things should I be checking? Routing issue or something even more complicated? [root@fogbugz ~]# cat /etc/sysconfig/network-scripts/ifcfg-eth0 # Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ DEVICE=eth0 BOOTPROTO=static IPADDR=72.249.134.98 NETMASK=255.255.255.248 BROADCAST=72.249.134.103 HWADDR=00:16:3E:AA:BB:EE ONBOOT=yes [root@fogbugz ~]# cat /etc/sysconfig/network-scripts/ifcfg-eth1 # Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ DEVICE=eth1 BOOTPROTO=static BROADCAST=10.3.20.255 HWADDR=00:17:3E:AA:BB:EE IPADDR=10.3.20.25 NETMASK=255.255.255.0 NETWORK=10.3.20.0 ONBOOT=yes [root@fogbugz ~]# cat /etc/sysconfig/network NETWORKING=yes NETWORKING_IPV6=no HOSTNAME=fogbugz.dfw.hisg-it.net GATEWAY=72.249.134.97 [root@fogbugz ~]# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 72.249.134.96 0.0.0.0 255.255.255.248 U 0 0 0 eth0 10.3.20.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 10.0.0.0 10.3.20.1 255.0.0.0 UG 0 0 0 eth1 0.0.0.0 72.249.134.97 0.0.0.0 UG 0 0 0 eth0

  Read the article

• Realtek/Intel NIC transfer speed

  - by thepurplepixel

  I have just purchased a Gigabyte GA-X58A-UD7 motherboard, and it has dual Realtek RTL8111D gigabit LAN ports. I also have an Intel PRO/1000 MT PCI gigabit network card lying around from an old desktop. I've heard that Intel PCI-E network cards will often outperform Realtek, Marvell, or other non-Intel on-board network adapters, but my question is will the PRO/1000 MT PCI card outperform a single Realtek RTL8111D gigabit network adapter in terms of transfer speed, or should I keep what I have/buy a PCI-E Intel network adapter?

  Read the article

• Router reconfigures PC's and they can no longer access the internet via hardwired connection to DSL Modem

  - by zchads

  Router reconfigures PC's and they can no longer access the internet via hardwired connection to DSL Modem. Hardware Information: Buffalo Wireless Router/access point, Model: WZR-HP-G300NH-AP DSL Modem: Generic (actually not sure of manufacture). Service Provider: TOT (Thailand) Laptop-1: Windows XP and Belkin PCMIA Network Card Laptop-2: Windows XP unknown network card & Wifi Laptop-3: Windows 7 unknown network card & Wifi Outline of Problem/actions taken: After a recent power failure the router and laptop-1 connected to router were no longer able to access the internet. Actions taken to try and recover internet access: Using Laptop-1 tried to configure Router with PPPoe settings using software from Router Manufacture. During the installation process a Timeout error was experienced, unable to connect to WAN. Used Internet Explorer to communicate directly with Router using IP address. Changed settings to use PPPoe settings given by ISP. Router was not able to communicate with Internet. Repeated steps 1-4 again with no success. Reset Router and DSL modem. Repeated steps 1-4 again still no success. Tried connecting Laptop-1 directly to DSL to gain access to internet to research problem. No Network connection with DSL could be established…connection would be established for a second and then be lost and didn’t appear long enough to actually connect to DSL. Replugged LAN back into Router and connection was regained with laptop-1. Replugged Laptop-1 directly into DSL and again unable to establish network connection. Uninstalled network card and all of its drivers on Laptop-1. Reinstalled network card and drivers and tried connecting directly to DSL. Still unable to make network connection. Plugged DSL into Laptop-3 and Internet connection was established. Being Laptop-3 does not have a CD-Rom, Laptop-2 was tried to connect to the router. With Laptop-2 steps 1-7 ended up being repeated without success. Tried plugging Laptop-2 directly into DSL and again no network connection could be established. Using Laptop-3 with a direct connection to DSL downloaded latest Router FW. Installed router FW using Laptop-1. Tired the installation process again without success. Being desperate reinstalled OS on Laptop-1 still not success. Tried using “ipconfig” with router to see what was going on without success. With laptop-1 connected to DSL went through the “ipconfig /…” inputs to see if anything made a difference. Being the network card was not able to make a connection this provide very little information “media disconnected”. So now I have a router and two laptops which are unable to connect to the internet and sure could use some advice/help.

  Read the article

• Exception when ASP.NET attempts to delete network file.

  - by Jordan Terrell

  Greetings - I've got an ASP.NET application that is trying to delete a file on a network share. The ASP.NET application's worker process is running under a domain account (confirmed this by looking in TaskManager and by using ShowContexts2.aspx¹). I've been assured by the network admins that the process account is a member of a group that has Modify permissions to the directory that contains the file I'm trying to delete. However, it is unable to do so, and instead I get an exception (changed the file path to all x's): System.Web.HttpUnhandledException: Exception of type 'System.Web.HttpUnhandledException' was thrown. --- System.UnauthorizedAccessException: Access to the path '\xxxxxxx\xxxxxxx\xxxxxxx\xxxxxx.xxx' is denied. Any ideas on how to diagnose/fix this issue? Thanks - Jordan ¹ http://www.leastprivilege.com/ShowContextsNET20Version.aspx

  Read the article

• What is the best software for network monitoring similar to spylogger?

  - by S.Mehdi

  What is the best software for network monitoring similar to spylogger?

  Read the article

• No network packets sent immediately after quick physical disconnect and reconnect.

  - by Hans

  I am using Boost's ASIO libraries to establish a UDP connection to a remote server. To make sure the connection is active, every second a keep-alive message is sent to the server. I have noticed that if I unplug the network cable and reinsert it quickly, the first 2 or 3 keep-alive messages after the reinsert are never sent. I tested this by running wire-shark on the server. I have seen it take up to 5 seconds before the client starts sending out network traffic again. The client is running under Linux (2.6.2), if that helps.

  Read the article

• What are the names of network interfaces on the Motorola CLIQ?

  - by RS

  The network interfaces on Android interfaces are listed as directories in the file system in /sys/class/net/. For most Android devices the network interface for gprs traffic is called rmnet0 and for Wi-Fi it's usually eth0 or tiwlan0. I suspect that the cell interface for the Motorola CLIQ is rmnet0, but I would like to have this confirmed + know the name of the Wi-Fi interface. Also it would be good to know the device id for this model. This is the value available as android.os.Build.DEVICE in the Java SDK. (E.g. T-Mobile G1 uses dream, Samsung Galaxy uses GT-I7500, and Motorolda Droid uses sholes.)

  Read the article

• alternate way to read excel files without providing "network service" security.

  - by Jebli

  Hi, I am using a web application to read the excel file and uploading it in the database. I have deployed the application in the server.I am using windows service 2003 as the server.I am able to read the excel file only if i set the set the security settings to "network service" for the microsoft excel application in the control panel -- administrative tools -- componetn service -- computer -- My computer -- DCOM config -- microsoft excel application . Why is it so . There are also other applications running in the server. 1) Doing like this will create any issue ? 2) Why do we need to do it ? 3) Is there any alternative way to do it ? 4) What are we doing actually by providing network service access ? Please help

  Read the article

• Can I override DropLocation target to avoid network latency?

  - by Chad

  In Team Build 2008, the Drop Location for a build is no longer specified in the .proj file, and instead is stored in the database and maintained in the GUI tool. The GUI tool only accepts a network path as a drop location (i.e. \\server\share) and will not accept a local path. Our build server also hosts the dropped files, so it seems that forcing a file copy operation to go through the network share introduces a lot of lag time when copying a large number of files. I would like to override this feature so that I can specify a local directory for drop location, but I can't figure out how.

  Read the article

• The difference between the 'Local System' account and the 'Network Service' account?

  - by jmatthias

  I have written a Windows service that spawns a separate process. This process creates a COM object. If the service runs under the 'Local System' account everything works fine, but if the service runs under the 'Network Service' account, the external process starts up but it fails to create the COM object. The error returned from the COM object creation is not a standard COM error (I think it's specific to the COM object being created). So, how do I determine how the two accounts, 'Local System' and 'Network Service' differ? These built-in accounts seem very mysterious and nobody seems to know much about them.

  Read the article

• Routing table with two NIC adapters in libvirt/KVM

  - by lzap

  I created a virtual NAT network (192.168.100.0/24 network) in my libvirt and new guest with two interfaces - one in this network, one as bridged (10.34.1.0/24 network) to the local LAN. The reason for that is I need to have my own virtual network for my DHCP/TFTP/DNS testing and still want to access my guest externally from my LAN. On both networks I have working DHCP, both giving them IP addresses. When I setup NAT port forwarding (e.g. for ssh), I can connect to the eth0 (virtual network), everything is fine. But when I try to access the eth1 via bridged interface, I have no response. I guess I have problem with my routing table - outgoing packets are routed to the virtual NAT network (which has access to the machine I am connecting from - I can ping it). But I am not sure if this setup is correct. I think I need to add something to my routing table. # ifconfig eth0 Link encap:Ethernet HWaddr 52:54:00:B4:A7:5F inet addr:192.168.100.14 Bcast:192.168.100.255 Mask:255.255.255.0 inet6 addr: fe80::5054:ff:feb4:a75f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:16468 errors:0 dropped:27 overruns:0 frame:0 TX packets:6081 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:22066140 (21.0 MiB) TX bytes:483249 (471.9 KiB) Interrupt:11 Base address:0x2000 eth1 Link encap:Ethernet HWaddr 52:54:00:DE:16:21 inet addr:10.34.1.111 Bcast:10.34.1.255 Mask:255.255.255.0 inet6 addr: fe80::5054:ff:fede:1621/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:34 errors:0 dropped:0 overruns:0 frame:0 TX packets:189 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4911 (4.7 KiB) TX bytes:9 # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.100.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.34.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 169.254.0.0 0.0.0.0 255.255.0.0 U 1002 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 1003 0 0 eth1 0.0.0.0 192.168.100.1 0.0.0.0 UG 0 0 0 eth0 Network I am trying to connect from is different than network the hypervisor is connected to: 10.36.0.0. But it is accessible from that network. So I tried to add new route rule: route add -net 10.36.0.0 netmask 255.255.0.0 dev eth1 And it is not working. I thought setting correct interface would be sufficient. What is needed to get my packets coming through?

  Read the article

• How to create an adhoc network between laptops in java?

  - by Muaz

  Hello, I want to create an adhoc between labtops were they will communicate using wireless communication. I will use java for this but still I do not know how to start.. I think I'll have to use sockets for the connections right? How will a laptop notice other laptops in its local network or the other way around? Do i need a server to handle the communication between laptops? Another thing, how to broadcast a message from one laptop to other laptops in the network? Please reply as soon as you can. Any help will be appreciated. Thanks in advance.

  Read the article

• How can I creat an ad-hoc network in iPhone?

  - by mac arthur

  I know the iphone has the ability to connect to an ad-hoc network, but it cannot create one ?

  Read the article

• Love coding but offered a server/network job -- any advice?

  - by Pete

  I really enjoy software development. I've done it for going on 3 years now full-time for a small company and still find it interesting and exciting. I haven't had much server/network experience but have an opportunity to work for a large IT company dealing with server setups, configurations, maintenance and some networking work as well. The thing is, I'm not sure whether to accept. If I were to take this, it would have relatively little if any coding and I'm guessing would start me down a career path away from coding. The only thing is the company is large enough and has a coding division so I guess in a few years I could transition back to the software side of things if I wanted, but I'm just not sure whether I would enjoy the server/network side of things. Any advice is greatly appreciated. Especially if you have had a similar situation occur. Thanks!

  Read the article

• How can i connect two or more machines via tcp cable to form a network grid?

  - by Gath

  How can i connect two or more machines to form a network grid and how can i distribute work load to the two machines? What operating systems do i need to run on the machines, and what application should i use to manage the load balancing? NB: I read somewhere that google uses cheap machines to perform this fete, how do they connect two network cards( 'Teaming' ) and distribute load across the machines? Good practical examples would serve me good, with actual code samples. Pointers to some good site i might read this stuff will be highly appreciated.

  Read the article

• If a server is performing slowly, will ping still appear normal?

  - by blarg

  I'm trying to troubleshoot a periodic slow application problem without direct access to the network. There is a server on one network providing webpages to a VLAN on a different network via a DMZ. I'm told that when the pages were loading slowly the user pinged the server and saw an extremely slow response time. My question is, as ping is minimal in network load and a different protocol from the pages, would a slow ping be caused by a slow server, or would it indicate a slow network?

  Read the article

• .NET 3.5 SP1 Code from Network - "The system cannot find the file specified."

  - by DaMoose

  This issue has nothing to do with whether the assemblies have been signed or caspol has been run for the shared network folder. Apparently, the location of the files is the issue, but I cannot find what the real problem is. I have one executable that references 5 dll's. I can run the app from a local drive without any problem. When I run the app from a network share, I get an error stating that "Could not load file or assembly 'homer, Version=1.0.0.0, Culture=neutral, PublicKeyToken=null' or one of its dependencies. The system cannot find the file specified." If all the files are in the same folder, what is the error really telling me? I should note also that the framework used is 3.5 SP1, which does not require changing code access policy. I had tried that anyhow, and I received the same error in both cases. Thanks, DaMoose

  Read the article

• What are the names of network interfaces on the Motorola CLIQ XT?

  - by RS

  The network interfaces on Android interfaces are listed as directories in the file system in /sys/class/net/. For most Android devices the network interface for gprs traffic is called rmnet0 and for Wi-Fi it's usually eth0 or tiwlan0. I suspect that the cell interface for the Motorola CLIQ XT is rmnet0, but I would like to have this confirmed + know the name of the Wi-Fi interface. Also it would be good to know the device id for this model. This is the value available as android.os.Build.DEVICE in the Java SDK. (E.g. T-Mobile G1 uses dream, Samsung Galaxy uses GT-I7500, and Motorolda Droid uses sholes.)

  Read the article

< Previous Page | 188 189 190 191 192 193 194 195 196 197 198 199  | Next Page >