Search Results

Search found 6164 results on 247 pages for 'sd card'.

Page 193/247 | < Previous Page | 189 190 191 192 193 194 195 196 197 198 199 200  | Next Page >

• Why doesn't Bumblebee work with Nvidia GT640M?

  - by Dickson Wong

  I've done a clean install of Ubuntu 12.04 from a liveCD on a Samsung Series 7 Chronos with a 3rd Gen i7 and the Nvidia GeForce GT 640M. I've followed this: (https://wiki.ubuntu.com/Bumblebee#Installation) to install bumblebee so I can switch to my discrete GPU. I have not used ironhide, or preivous bumblee since it's a clean install. When I use optirun, optirun says it can't initialize the GPU: [ERROR]Cannot access secondary GPU - error: [XORG] (EE) NVIDIA(0): Failed to initialize the NVIDIA GPU at PCI:1:0:0. Please [ERROR]Aborting because fallback start is disabled. I've looked at the troubleshooting page for bumblebee and I have the correct driver and do not think I have aspci disabled. Also, my keyboard becomes very unresponsive and my mouse skips and isn't smooth after optirun crashes. The only thing to fix this is a reboot. Here's my lspci | grep VGA output: 00:02.0 VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09) 01:00.0 VGA compatible controller: NVIDIA Corporation Device 0fd2 (rev ff) It seems Ubuntu can see my graphics card. I don't really know what's going on.

  Read the article

• Dock with dual external DVI monitors with Intel + Nvidia Optimus?

  - by Ryan

  I have a Dell Latitude E6420 laptop plugged into a docking station, and the dock has 2 monitors (connected with DVI). Also note that I've installed Ubuntu alongside (dual-boot) Windows 7. I can't get the dual monitors to work both on Ubuntu (either 11.10 or 12.04) and Windows 7. When I run lspci | grep VGA, I get: 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 01:00.0 VGA compatible controller: nVidia Corporation GF108 [Quadro NVS 4200M] (rev a1) If I then reboot and uncheck Optimus setting in the BIOS during reboot, I'm able to get the dual monitors to work in Ubuntu 12.04 (but I need to configure them every boot in Nvidia Settings). When I run lspci | grep VGA, I get: 01:00.0 VGA compatible controller: NVIDIA Corporation GF119 [Quadro NVS 4200M] (rev a1) But then if I reboot into Windows (leaving the Optimus unchecked), Windows can't detect external monitors, and the resolution is unacceptably low. I've seen on many forum posts that this particular graphics card setup causes lots of headaches. I haven't been able to resolve my problem yet. How can I use my external display on my laptop with intel and nvidia video cards? How to use external displays with Intel driver on a NVidia/Intel hybrid system nVidia Optimus , Unity 3D and Dual Monitors "Just use VGA instead of DVI" isn't an option because my dock has only 1 VGA port (and 2 DVI). Switching the BIOS setting on every reboot and then reconfiguring the display settings every time is tedious, time-consuming, and impractical. Do you know how to make this work smoothly? Thanks for your help! P.S. see also: http://superuser.com/questions/434358/dell-latitude-e6420-dual-boot-ubuntu-windows-7-optimus-graphics-problems

  Read the article

• Which problem(s) do YOU want to see solved?

  - by buu700

  My team and I are meeting tonight to come up with a business plan and some community input would be amazing. I've been mulling over this issue for the past few months and bouncing ideas off of others, and now I'd finally like some input from the community. I have come up with a fair selection of ideas, but most of those amount to either fun projects which could potentially be profitable, or otherwise solid business models that have one or two major hurdles (usually related to resources or legality). For our team meeting tonight, my idea is to take inventory of our available skills, resources, and compelling problems which interest us. The last is where I would greatly appreciate some community input. Hell, even entire business ideas/plans would be appreciated. No matter how big or small your thoughts, any input would be appreciated. We're a team of computer scientists, so our business will be primarily based around software/technology/Web solutions. Among my relevant available resources (entire Internet aside), I have the following: A pretty reliable connection to an SEO company a large production company. A stash of fairly powerful server hardware. A fast network with static IPs. The backend for Hackswipe, which includes credit card payment processing and a Google Voice-based SMS gateway. This work in progress design for something completely unrelated but which is backed by some fairly decent infrastructure. Direct access to the experts in just about any relevant field (on-campus Carnegie Mellon professors). A sexual relationship with the baron of a small nation. For further down the line, some investor relationships. Not likely to be so relevant, but a decent social media presence (Stack Overflow reputation, modship in some major reddits, various tech forums). The source code for Eugene fucking McCabe. Pooled with the other team members, the list of projects we can build off of would be longer (including an Android app). So, what are your thoughts? Crossposted to reddit

  Read the article

• Unity's gone! How do I get it back?

  - by Kelley

  Earlier today my Unity desktop disappeared: I got a black screen with white text, but it disappeared too quickly for me to read. When the desktop reappeared, it was the Ubuntu Classic desktop. I used $ unity --reset but that did not do anything. I tried rebooting so I could choose unity from the list when I logged in, but although there was Ubuntu choice, there was no unity listed (but classic was listed). I was able to install Unity 2D and am using that, but really want to get 3D back. I had been using Ubuntu without problems for several weeks when this happened. My graphics card is onboard a Dell Latitude desktop - a couple years old - and is reported as an Intel G33/G31. I've looked at other requests for help here, and tried suggestions when they seemed to relate to similar problems, but nothing seems to work so far. Any ideas? Thanks! This is part of the output of my latest attempt to run unity --reset Window manager warning: 0x3e01c35 () appears to be one of the offending windows with a timestamp of 1309472834. Working around... Window manager warning: last_user_time (1309473695) is greater than comparison timestamp (1126160). This most likely represents a buggy client sending inaccurate timestamps in messages such as _NET_ACTIVE_WINDOW. Trying to work around... Window manager warning: 0x4c0046c (mdk@Habane) appears to be one of the offending windows with a timestamp of 1309473695. Working around... Window manager warning: Received a NET_CURRENT_DESKTOP message from a broken (outdated) client who sent a 0 timestamp Window manager warning: Buggy client sent a _NET_ACTIVE_WINDOW message with a timestamp of 0 for 0x4c0046c (mdk@Habane) Window manager warning: meta_window_activate called by a pager with a 0 timestamp; the pager needs to be fixed.

  Read the article

• How do I get network working on a Dell n5010 - Ubuntu 10.04

  - by cyberroger

  Hey. I just formatted a Dell n5010 and installed Ubuntu 10.04. Now,when i try to access the Internet it doesn't find the available networks. Informations about it: My network is set to broadcast SSID; Already typed lspci, and it doesnt returns my wireless card; Tried installing windows drivers from fabricant cd usind diswrapper, but it says it cant complete the installation because it cant find some "Device" folder; I don't know what else to do, I switch the wireless button on/off and it just can't see any wireless connection, includin mine. Here are the informations about lspci: *-network UNCLAIMED description: Network controller product: Broadcom Corporation vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:12:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:fbc00000-fbc03fff And this: 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 18) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 18) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06) 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 06) 00:1c.2 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 3 (rev 06) 00:1c.4 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 5 (rev 06) 00:1d.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a6) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 06) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 6 port SATA AHCI Controller (rev 06) 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 06) 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 06) 12:00.0 Network controller: Broadcom Corporation Device 4727 (rev 01) 13:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 02) Thanks!

  Read the article

• How to partition Seagate FreeAgent GoFlex 2TB hard disk?

  - by balki

  Hi I bought a new Seagate 2TB external hard disk. I opened the drive's application in my virtual windows, did product registration using the application present in it. I have few questions on how best to use it. The drive by default has some files and folders - setup.exe, System Volume Information, USB 3.0 PC Card Adapter etc,. I copied all the files to my laptop. Is it safe to delete these files? It has a dash board for windows which allows to tune power options, test the drive etc. Will I be able to use the dash board if I put back all these files and mount on windows again? I want to partition and format the hard disk. Data I like to store is Around 10 to 20 GB Files - Virtual box images. Around 4GB Files - Dvd images. Other Movies and personal Files. What is the best filesystem to store very huge files like 10 to 20GB files. So that they are written and accessed fast also best uses the drive's capacity. If I leave one of the partition as ntfs and others to different files systems, will it be able to mount on windows and Will I be able to use the device's dash board? Note: I dont need any encryption for my data. Any other advice on using the hard disk is also welcome.

  Read the article

• How do I stop my ethernet network connection from dropping?

  - by Sean Hill

  My ethernet-based network connection doesn't stay up consistently. I'm running a ping against the gateway and it will: Work for a minute Freeze, time out, or give multi-second response times Repeat If it's stuck and I disable/enable networking through the network manager applet everything will work fine again for a minute. After 280 packets transmitted I'm getting 41% packet loss. I've tried a different cable and connection to the gateway but this had no effect. The distance to the gateway is just about 3 feet. Seems to work fine if I switch over to Windows, but Ubuntu is my main OS and I can't even use it right now as I depend on the network. My setup... OS: Ubuntu 11.04, dual-booting Windows 7 Mobo: Gigabyte Z68X-UD4-B3 CPU: Intel Core i7 2600K Edit A little clarification... Network Manager is still showing me as connected, but I am unable to reach to gateway or anything beyond. At no point does NM suggest the connection is lost and calling ifconfig shows that I still have an IP address. I tried connecting to a different gateway with a different cable and the same problem arises. As requested: lspci | grep -i eth 07:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) dmesg | tail -f [ 14.024709] EXT4-fs (sda5): re-mounted. Opts: errors=remount-ro,commit=0 [ 14.026443] EXT4-fs (sda7): re-mounted. Opts: commit=0 [ 14.176101] hda-intel: IRQ timing workaround is activated for card #2. Suggest a bigger bdl_pos_adj. [ 23.917731] eth0: no IPv6 routers present [ 726.109697] r8169 0000:07:00.0: eth0: link up [ 733.169494] r8169 0000:07:00.0: eth0: link up [ 753.930119] r8169 0000:07:00.0: eth0: link up [ 880.787332] r8169 0000:07:00.0: eth0: link up [ 1159.161283] r8169 0000:07:00.0: eth0: link up [ 1406.623550] r8169 0000:07:00.0: eth0: link up Edit @roland-taylor: Network is always available under Windows. Pings do not timeout, applications do not complain of no network availability, large downloads are not interrupted or slowed.

  Read the article

• Ubuntu and racadm

  - by lmqcn

  I recently purchased a used poweredge 1850 server and it came with a DRAC card. After wiping the HDD and installing ubuntu server 12.04.3 LTS amd64 on it, I am now trying to gain access to the DRAC which I believe is version 4. I have properly configured the DRAC to use it's own IP on my LAN and when I point my browser to the IP address, I am greeted with the DRAC login page (it has the dell logo and everything). However, after trying the credentials of root/calvin, I was denied access. So I think that the previous owners had set their own password. After doing some reading, it appears that I can reset the credentials to the default using racadm config -g cfgUserAdmin -o cfgUserAdminPassword -i 1 newpassword but upon entering the command, I get this error: bash: /usr/sbin/racadm: No such file or directory This holds true even if I run sudo su prior to running the racadm command. If, however, I run sudo racadm config -g cfgUserAdmin -o cfgUserAdminPassword -i 1 newpassword there are no errors. Yet, when I try to log into the DRAC via the web interface using the credentials of root/newpassword I am still not granted access. I installed the dell utilities via the guide at https://wiki.ubuntu.com/HardwareSupportMachinesServersDellNotes. I first tried to install the 64 bit version that is on the dell repositories, but after that was unsuccessful, I just followed the guide verbatim. No errors were produced in either case. I even followed the information at the bottom of the guide by executing sudo pppd /dev/ttyS1 1382400 crtscts noipdefault noauth lock persist connect 'chat -v "" CLIENT CLIENTSERVER "\\c"' but obviously, replacing the /dev/ttyS1 with the correct information for my system. ls -l /usr/sbin/ | grep racadm yields -rwxr-xr-x 1 root root 87930 Sep 16 04:03 racadm I have tried these credentials after each attempt of changing the password: root/calvin root/newpassword admin/calvin admin/newpassword All have been unsuccessful. What is the next course of action that I should take?

  Read the article

• Can not access Internet (DNS names do not resolve) after update today

  - by Aras

  I have been using Precise for a few weeks now for work with no problem. Today, I am not able to access any website using either wired or wireless connections. I installed the updates today which included nautilus, xserver, and a new kernel (3.2.0-24). After restarting I no longer was able to browse the Internet using firefox or chrome. Trying to ping google in terminal gives ping: unknown host google.ca I have tried: Connecting to wireless or wired networks (both working on other machines) Restart the machine and boot with previous Kernel Manually configure opendns on my wired connection Restart the network and the laptop and the wireless card Without any success so far. I am not sure where to go next. Please let me know the cause of the issue or help me troubleshoot it. Note that the laptop does receive an ip address, and it can ping ip address of google.ca (74.125.127.94) but not the domain name, or any domain name for that matter. This system was upgraded from 11.10 to 12.04 more two weeks ago.

  Read the article

• How to revert back to older xorg?

  - by wouter205

  Since the last update of ubuntu 12.04, the system won't boot into gui anymore. It states that it was unable to load the graphics drivers and gives me 4 options, these are: run in low graphics mode for 1 session reconfigure graphics troubleshoot the error exit to console login whichever option I choose, it doesn't solve anything. For instance, when i choose to reconfigure graphics and then switch to vesa drivers, the screen goes back to the option list. So i configured xorg.conf to vesa myself, and i see in the update history that ubuntu updated xserver-xorg-core and xserver-common whereas i blocked these updates in synaptic since i'm aware that updating these files caused troubles with my particular video card (radeon hd6800). So my solution is probably to revert these files to the older (working) versions. How can I do this please (in particular xserver-xorg-core since i think this is the main cause of my problem). thanks! output of ls /etc/X11 -app-defaults xorg.conf Xreset -cursors xorg.conf-backup-120529144709 Xreset.d -default-display-manager xorg.conf.fglrx-0 -Xresources -fonts xorg.conf.fglrx-1 Xsession -rgb.txt xorg.conf.fglrx-2 Xsession.d -X xorg.conf.original-0 -Xsession.options -xinit xorg.conf.original-1 -Xwrapper.config -xkb xorg.conf.vesa Output of sudo aptitude show xserver-xorg-core | grep Versie (read: Version in Flemish) Versie: 2:1.11.4-0ubuntu10.2

  Read the article

• PCI compliance when using third-party processing

  - by Moses

  My company is outsourcing the development of our new e-commerce site to a third party web development company. The way they set up our site to handle transactions is by having the user enter the necessary payment info, then passing that data to a third party merchant that processes the payment, then completing the transaction if everything is good. When the issue of PCI/DSS compliance was raised, they said: You wont need PCI certification because the clients browser will send the sensitive information directly to the third party merchant when the transaction is processed. However, the process will be transparent to the user because all interface and displays are controlled by us. The only server required to be compliant is the third party merchant's because no sensitive card data ever touches your server or web app. Even though I very much so trust and respect the knowledge of our web developers, what they are saying is raising some serious red flags for me. The way the site is described, I am sure we will not be using a hosted payment page like PayPal or Google Checkout offers (how could we maintain control over UI if we were?) And while my knowledge of e-commerce is laughable at best, it seems like the only other option for us would be to use XML direct to communicate with our third party merchant for processing. My two questions are as follows: Based off everything you've read, is "XML Direct" the only option they could conceivably be using, or is there another method I don't know of which they could be implementing? Most importantly, is it true our site does not need PCI certification? As I understand it, using the XML direct method means that we do have to be PCI/DSS certified, and the only way around getting certified is through a payment hosted page (i.e. PayPal).

  Read the article

• 2D platformers: why make the physics dependent on the framerate?

  - by Archagon

  "Super Meat Boy" is a difficult platformer that recently came out for PC, requiring exceptional control and pixel-perfect jumping. The physics code in the game is dependent on the framerate, which is locked to 60fps; this means that if your computer can't run the game at full speed, the physics will go insane, causing (among other things) your character to run slower and fall through the ground. Furthermore, if vsync is off, the game runs extremely fast. Could those experienced with 2D game programming help explain why the game was coded this way? Wouldn't a physics loop running at a constant rate be a better solution? (Actually, I think a physics loop is used for parts of the game, since some of the entities continue to move normally regardless of the framerate. Your character, on the other hand, runs exactly [fps/60] as fast.) What bothers me about this implementation is the loss of abstraction between the game engine and the graphics rendering, which depends on system-specific things like the monitor, graphics card, and CPU. If, for whatever reason, your computer can't handle vsync, or can't run the game at exactly 60fps, it'll break spectacularly. Why should the rendering step in any way influence the physics calculations? (Most games nowadays would either slow down the game or skip frames.) On the other hand, I understand that old-school platformers on the NES and SNES depended on a fixed framerate for much of their control and physics. Why is this, and would it be possible to create a patformer in that vein without having the framerate dependency? Is there necessarily a loss of precision if you separate the graphics rendering from the rest of the engine? Thank you, and sorry if the question was confusing.

  Read the article

• Creating a retro-style palette swapping effect in OpenGL

  - by Zack The Human

  I'm working on a Megaman-like game where I need to change the color of certain pixels at runtime. For reference: in Megaman when you change your selected weapon then main character's palette changes to reflect the selected weapon. Not all of the sprite's colors change, only certain ones do. This kind of effect was common and quite easy to do on the NES since the programmer had access to the palette and the logical mapping between pixels and palette indices. On modern hardware, though, this is a bit more challenging because the concept of palettes is not the same. All of my textures are 32-bit and do not use palettes. There are two ways I know of to achieve the effect I want, but I'm curious if there are better ways to achieve this effect easily. The two options I know of are: Use a shader and write some GLSL to perform the "palette swapping" behavior. If shaders are not available (say, because the graphics card doesn't support them) then it is possible to clone the "original" textures and generate different versions with the color changes pre-applied. Ideally I would like to use a shader since it seems straightforward and requires little additional work opposed to the duplicated-texture method. I worry that duplicating textures just to change a color in them is wasting VRAM -- should I not worry about that?

  Read the article

• Can't enable wireless lan on Fujitsu Siemens A1665G with Ubuntu 11.10 installed

  - by Theo

  I saw my old Notebook yesterday and wanted to make that work again. On Windows XP the wireless worked still fine. Then I installed new Ubuntu 11.10 32bit and I'm sadly not able to make the wireless enabled. [I replaced Win XP entirely] lspci lists following network: 08:0a.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02) So after recommendation from this link I installed the b43 firmware module. iwconfig prints the following: wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associatd Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management: off As you can see, my wireless lan adapter is not turned on. sudo iwconfig wlan0 txpower auto Doesn't change anything. Then I tried to make it work with rfkill. rfkill list 0: phy0: Wirless LAN Soft blocked: no Hard blocked: yes sudo rfkill unblock all rfkill list 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes remains the same. The question is now, how I could enable the hard blocked wireless LAN. There is no hardware switch for wlan integrated. However there is a button to change the state. I always thought this would be software sided, but it seems to make some hardware changes as well... The wireless LED is also not blinking (as it did on windows xp) I reset bios and searched for some settings in there, but it has only a few options and nothing to do with wireless settings, nothing works here.. At last I tried to install the acer hotkeys but I was not able to manage that. I installed the acerhkgui package, but in initializing progress, it was not able to compile acer hotkeys for my machine. There was a message that asm/linkage.h was not found while compiling. Do you have any ideas what I could do to make this hard blocked stuff disabled and my wireless card work? PS: I also tried sudo rm /dev/rfkill and a reboot to reinit that stuff... No success :(

  Read the article

• Network Issues only on one network with a Broadcom BCM4312

  - by Ryan McClure

  My Ubuntu 11.10 laptop is having network connection issues...only on one network. I have a BCM4312 card and I'm using the proprietary driver. Whenever I connect to a network over wireless connection, I have no trouble except for one network. In my dorm, if I try to connect to the wireless network, it stays connected from anywhere to 30 seconds to 30 minutes before it will still be "connected" according to the indicator but there is no incoming/outgoing internet connection. This only happens in this building. Other networks with the same name at other buildings on my campus have no issue whatsoever. I took it to the tech department here and they keep claiming it's my laptop; but, if I can connect to other networks with absolutely no issues, why can't my laptop connect here? So, here's my question: Is it my laptop, or is it the network? As a side note, no one else that I know has issues on this network but one; she's running Windows 7 and I forget what kind of laptop it is. One of the people in my hall runs Ubuntu 12.04 and has no problem with the wireless. What do you all think of this?

  Read the article

• double screen in ubuntu 12.04?

  - by johan

  I am using ubuntu 12.04 and my video card is ATI Radeon 5000. I cannot use double screen (extended version). I get this error The selected configuration for displays could not be applied requested position/size for CRTC 148 is outside the allowed limit: position=(1280, 0), size=(1280, 768), maximum=(1440, 1440) I tried all display settings but it does not work. Some outputs from the system settings: root@ubuntu:~# lshw -C display *-display description: VGA compatible controller product: Madison [Radeon HD 5000M Series] vendor: Hynix Semiconductor (Hyundai Electronics) physical id: 0 bus info: pci@0000:01:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm pciexpress msi vga_controller bus_master cap_list rom configuration: driver=fglrx_pci latency=0 resources: irq:46 memory:e0000000-efffffff memory:f0020000-f003ffff ioport:d000(size=256) memory:f0000000-f001ffff root@ubuntu:~# aticonfig --initial Uninitialised file found, configuring. Using /etc/X11/xorg.conf Saving back-up to /etc/X11/xorg.conf.original-0 root@ubuntu:~# cat /etc/X11/xorg.conf Section "ServerLayout" Identifier "aticonfig Layout" Screen 0 "aticonfig-Screen[0]-0" 0 0 EndSection Section "Module" Load "glx" EndSection Section "Monitor" Identifier "aticonfig-Monitor[0]-0" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" EndSection Section "Device" Identifier "aticonfig-Device[0]-0" Driver "fglrx" BusID "PCI:1:0:0" EndSection Section "Screen" Identifier "Default Screen" DefaultDepth 24 EndSection Section "Screen" Identifier "aticonfig-Screen[0]-0" Device "aticonfig-Device[0]-0" Monitor "aticonfig-Monitor[0]-0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection I would appreciate any suggestions how to solve the problem. Thank you

  Read the article

• 12.04 kernel panic

  - by jesus

  Hello I'm having trouble with Ubuntu 12.04. I downloaded the ISO and burned it into a CD and tried to install Ubuntu, but during the installation process, I got this message Kernel panic-not syncing Attempted to kill init! pid:1,comm:init not tainted 3.2.0-23-generic-pae#36-ubunru then it says switching to console text, and it just hangs in there and nothing happens. I burned another CD with Ubuntu 10.04, but I get a different problem: Ubuntu just gets stuck at the splash screen with the 5 dots which move from red to white, and nothing happens. I was able to boot before with 10.04 but I recently upgraded my computer graphics card and power supply. please see my system specs. Gigabyte GA-M68M-S2P (rev. 2.3) GeForce 7025 Chipset Athalon II x4 640 QuadCore Radeon HD 6870 sapphire OCZ ModXStream Pro 600W Modular High Performance Power Supply 3 hard drives one is IDE and the other two SATA IDE DVD Drive If any one could help me, I'd be most appreciative. If it helps I tried the F6 option like acpi=off noapic nolapic nomodset but i still get kernel panic

  Read the article

• Cannot set monitor to native resolution

  - by S B

  problem is similar to so many other users, but solutions found do not work. Background: Fresh install of 12.04 (completely updated) on a Fit-PC2 (specs). Read in several places that the new 3.X kernel that 12.04 runs on has a new psb_gfx driver which supports the gma500 graphics card (poulsbo chipset). All's pretty much working (there are some glitches which are documented, so I won't raise them here), except for the screen resolution. My native monitor resolution is 1920X1080, but all I get is 1024x768. Output running xrandr: xrandr: Failed to get size of gamma for output default Screen 0: minimum 1024 x 768, current 1024 x 768, maximum 1024 x 768 default connected 1024x768+0+0 0mm x 0mm 1024x768 0.0* Although I read that Ubuntu does not come with an xorg.conf file anymore, I also tried running sudo X :1 -configure, and here's the end of the output: Number of created screens does not match number of detected devices. Configuration failed. When I look in the xorg.conf.new file created in my home directory, it seems that for some reason X thinks I have two screens. Don't know what to do with that. Ideas anyone? Thanks for your time.

  Read the article

• Why am I not getting an sRGB default framebuffer?

  - by Aaron Rotenberg

  I'm trying to make my OpenGL Haskell program gamma correct by making appropriate use of sRGB framebuffers and textures, but I'm running into issues making the default framebuffer sRGB. Consider the following Haskell program, compiled for 32-bit Windows using GHC and linked against 32-bit freeglut: import Foreign.Marshal.Alloc(alloca) import Foreign.Ptr(Ptr) import Foreign.Storable(Storable, peek) import Graphics.Rendering.OpenGL.Raw import qualified Graphics.UI.GLUT as GLUT import Graphics.UI.GLUT(($=)) main :: IO () main = do (_progName, _args) <- GLUT.getArgsAndInitialize GLUT.initialDisplayMode $= [GLUT.SRGBMode] _window <- GLUT.createWindow "sRGB Test" -- To prove that I actually have freeglut working correctly. -- This will fail at runtime under classic GLUT. GLUT.closeCallback $= Just (return ()) glEnable gl_FRAMEBUFFER_SRGB colorEncoding <- allocaOut $ glGetFramebufferAttachmentParameteriv gl_FRAMEBUFFER gl_FRONT_LEFT gl_FRAMEBUFFER_ATTACHMENT_COLOR_ENCODING print colorEncoding allocaOut :: Storable a => (Ptr a -> IO b) -> IO a allocaOut f = alloca $ \ptr -> do f ptr peek ptr On my desktop (Windows 8 64-bit with a GeForce GTX 760 graphics card) this program outputs 9729, a.k.a. gl_LINEAR, indicating that the default framebuffer is using linear color space, even though I explicitly requested an sRGB window. This is reflected in the rendering results of the actual program I'm trying to write - everything looks washed out because my linear color values aren't being converted to sRGB before being written to the framebuffer. On the other hand, on my laptop (Windows 7 64-bit with an Intel graphics chip), the program prints 0 (huh?) and I get an sRGB default framebuffer by default whether I request one or not! And on both machines, if I manually create a non-default framebuffer bound to an sRGB texture, the program correctly prints 35904, a.k.a. gl_SRGB. Why am I getting different results on different hardware? Am I doing something wrong? How can I get an sRGB framebuffer consistently on all hardware and target OSes?

  Read the article

• Xubuntu 14.04 with Compton, strange screen tearing, only when playing videos though (advice needed)

  - by LinuxDudester

  Hello beloved community, Yet again I am in need of your great expertise. I ran into a very strange issue and just can't wrap my mind around it. I'm running Xubuntu 14.04 exclusively, with Compton installed. The OS runs great and I have absolutely no screen tearing when I move my windows around, scroll in my web browser, work in Gimp or Photoshop (wine) or even when I play very graphic demanding games, like Metro Last Light, Euro Truck Driver 2 and so on. There's not a tiny bit of tearing to see, but as soon as I play videos, in xbmc, vlc or parole media player the tearing begins (strangely enough this does not apply to youtube videos). I followed all available workarounds on askubuntu and the ubuntu forum,like the 50-xserver-command.conf, startx /etc/X11/Xsession /usr/bin/xbmc-standalone -- -bs or libsdl1.2debian fix and many more, but to no avail. I also tried the Open Source Nouveau display drivers as well, but for some odd reason they don't work so great on my system or at least with my graphics card. Even with Compton installed and configured, I have an extreme amount of screen tearing, as soon as I switch to the proprietary Nvidia drives the screen tearing is gone completely, except for the video playback with xbmc, vlc or parole media player. System info for your reference: OS: Xubuntu 14.04 Linux-x86_64 - Processor: Intel Core i7-4770S CPU @ 3.10GHz - Ram: 16 GB - GeForce GT 750M 1024 MB - Nvidia Driver: 331.38 Has anyone experienced such an odd issue or do you have any advice on how I could fix this? I would appreciate any help! Have a nice day!

  Read the article

• Creating a newspaper that effects the game's economy?

  - by zardon

  I am writing a game in Objective C/cocos2d where a newspaper is a central part of what controls or rather effects the game's world economy as well as what a city might do (such as increase X, reduce Y) The newspaper is a bit like a "Chance card" in Monopoly, it has an effect on something. My question is, what is the best way to do write a newspaper that has both a random and specific effect within the game. Would the best strategy be to write out all the things a newspaper can affect, a PLIST of headlines (with placeholders). I think Tiny Tower uses a PLIST of events and it randomly picks an event, but I'm not sure how it actually parses it because certain events do different things. But then how do I parse all the scenarios that a newspaper can deliver? A big switch statement seems very long and complicated to do. I am wondering if there is a simpler way to handle this kind of thing. Related to this is that there might be no news that day and I'm not sure what the newspaper should display, should it just display the last headline? So, in summary. 1) A newspaper generates a headline, it affects different things, such as the world economy, prices, how city reacts 2) I need the newspaper to generate headlines (although there may be days when there are no headlines at all), but I am not sure how to parse it without using a big-ass switch statement. Thanks in advance.

  Read the article

• Sozialgericht Düsseldorf weist Klage gegen elektronische Gesundheitskarte zurück

  - by Anne Manke

  In einem Musterverfahren wurde die Klage gegen die elektronische Gesundheitskarte (eGK) vom Düsseldorfer Sozialgericht zurückgewiesen. Das Gericht urteilte heute, die eGK, die bis Ende des Jahres an mindestens 50 Millionen Versicherte verteilt soll, sei in ihrer aktuellen Form gesetzes- und verfassungskonform. Der 32-jährige Kläger hatte sich mit dieser Klage von der Nutzung der Plastikkarte befreien wollen. Er sah sein Recht auf informationelle Selbstbestimmung verletzt und hatte datenschutzrechtliche Bedenken gegen die eGK. Nun wurde er, und alle anderen Versicherten, mit dem Urteilsspruch des Düsseldorfer Gerichts zur Nutzung der eGK gesetzlich verpflichtet. Die elektronische Gesundheitskarte gerät immer wieder ins Fadenkreuz der Kritik. Datenschützer, Patienten- und Ärzteverbände sowie Bürgerrechtsbewegungen befürchten, dass die eGK in ihrer derzeitigen Form nicht genügend Schutz für private Daten der Versicherten bieten würde. Der Patient würde mit der elektronischen Gesundheitskarte zum "gläsernen Patienten".  Das Gericht wies die Klage mit der Argumentation zurück, die elektronische Gesundheitskarte würde in ihrer aktuellen Form, wie auch schon die alte Versichertenkartem, lediglich Stammdaten der Versicherten speichern. Desweiteren seien alle zuküftigen Anwendungen nur mit Zustimmung des Versicherten möglich.  Der Kläger, der durch das Bündnis "Stoppt die E-Card" unterstützt wird, kündigte an, bis vor das Bundesverfassungsgericht ziehen zu wollen, sollte seiner Klage nicht vorher stattgegeben werden. 

  Read the article

• No WIFI or LAN on Ubuntu 12.04 or 12.10 Live CD/USB using Toshiba qosmio x870

  - by Mighty

  I recently had issues with secure boot and couldn't boot the Live CD/USB but after disabling secure boot, I was able to 'TRY UBUNTU'. My currently problem is that I can't access WIFI or LAN from either Ubuntu 12.04 or 12.10 Live CD/USB which I do from Windows 8. Also, the wireless button is able to turn on and off the wireless LED but doesn't find available WIFI. Please, what should I do to get both WIFI and LAN working on Ubuntu using Toshiba qosmio x870? UPDATED: Here's the output of lspci: ubuntu@ubuntu:~$ lspci 00:00.0 Host bridge: Intel Corporation 3rd Gen Core processor DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 3rd Gen Core processor Graphics Controller (rev 09) 00:14.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation 7 Series/C210 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 1 (rev c4) 00:1c.1 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 2 (rev c4) 00:1c.4 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 5 (rev c4) 00:1d.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation HM76 Express Chipset LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation 7 Series Chipset Family 6-port SATA Controller [AHCI mode] (rev 04) 00:1f.3 SMBus: Intel Corporation 7 Series/C210 Series Chipset Family SMBus Controller (rev 04) 01:00.0 VGA compatible controller: NVIDIA Corporation Device 1213 (rev a1) 07:00.0 Ethernet controller: Atheros Communications Inc. AR8161 Gigabit Ethernet (rev 10) 08:00.0 Network controller: Realtek Semiconductor Co., Ltd. Device 8723 09:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS5229 PCI Express Card Reader (rev 01)

  Read the article

• No GUI boot; startx error, I suspect no filesystem corruption.

  - by Dharmaj Soni

  Till yesterday, my Ubuntu 9.10 was working fine. I had watched a movie using vlc. I had also charged my ipod using the laptop. Today, when I started it, I automatically booted into command line. There seems to be no filesystem corruption etc as I can view/open (text) files. Before the CLI appeared, the screen blinked with a cursor, then the white Ubuntu logo flashed, and then I got the CLI login prompt. After logging in, if I try startx, to start gnome, I get the following error after a few seconds: giving up xinit: No such file or directory (errno 2): unable to connect to X server xinit: No such process (errno 3): Server error* The same error comes up, even if I use sudo, or if I change my directory to '/' before using startx, and also when, from the grub, using the recovery mode option to load into CLI, and then trying startx. On trying command 'xinit', I get "Server error" Also, on trying GDM, I get 2 errors. I cannot connect to the internet in this state. Thanks for any help. I am using Dell Inspiron 1440, no special graphics card.

  Read the article

• DIA2012

  - by Chris Kawalek

  If you've read this blog before, you probably know that Oracle desktop virtualization is used to demonstrate Oracle Applications at many different trade shows. This week, the Oracle desktop team is at DIA2012 in Philadelphia, PA. The DIA conference is a large event, hosting about 7,000 professionals in the pharmaceutical, bio technology, and medical device fields. Healthcare and associated fields are leveraging desktop virtualization because the model is a natural fit due to their high security requirements. Keeping all the data on the server and not distributing it on laptops or PCs that could be stolen makes a lot of sense when you're talking about patient records and other sensitive information. We're proud to be supporting the Oracle Health Sciences team at DIA2012 by hosting all of the Oracle healthcare related demos on a central server, and providing simple, smart card based access using our Sun Ray Clients. And remember that you're not limited to using just Sun Ray Clients--you can also use the Oracle Virtual Desktop Client and freely move your session from your iPad, your Windows or Linux PC, your Mac, or Sun Ray Clients. It's a truly mobile solution for an industry that requires mobile, secure access in order to remain compliant. Here are some pics from the show: We also have an informative PDF on Oracle desktop virtualization and Oracle healthcare that you can have a look at.  (Many thanks to Adam Workman for the pics!) -Chris  For more information, please go to the Oracle Virtualization web page, or  follow us at :  Twitter   Facebook YouTube Newsletter

  Read the article

< Previous Page | 189 190 191 192 193 194 195 196 197 198 199 200  | Next Page >