Search Results

Search found 14509 results on 581 pages for 'print driver'.

Page 195/581 | < Previous Page | 191 192 193 194 195 196 197 198 199 200 201 202  | Next Page >

• Cannot enable wireless on an Intel WifiLink 1000 on an Lenovo Ideapad z570

  - by Brij

  I am using the ubuntu 11.10 on lenovo ideapad z570. My wireless internet is not working. I have ensure that wireless switch is on. Windows 7, wireless works great.However ubuntu 11.10 is not allowing me to enable wireless connection. I have run the following command and here is the status. sudo lshw -class network *-network DISABLED description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 00 serial: 74:e5:0b:1c:a4:a4 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-12-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:42 memory:d0500000-d0501fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 05 serial: f0:de:f1:64:b6:62 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl_nic/rtl8105e-1.fw latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:41 ioport:2000(size=256) memory:d0404000-d0404fff memory:d0400000-d0403fff Here is rfkill list all output: rfkill list all 0: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no 2: acer-wireless: Wireless LAN Soft blocked: yes Hard blocked: no Note : Windows 7, wireless card property shows that Intel WifiLink 1000 BGN. Could someone help me to fix this issue.

  Read the article

• How to switch sound-drivers, and to which? [AMD] Hudson Azalia Controller

  - by Anders Martini

  System settings/sound does not open, freezes and I have to force close. Speaker symbol with volume control does not open scroll-down menu, and there is no sounds. Many people have problems with Hudson Azalia in Ubuntu, but I found no working solution. I don't really understand much of this, but here are some more details: aplay -l : **** List of PLAYBACK Hardware Devices **** (after running this one, it starts some kind of process that doesn't get any results, and doesn't stop, terminal has to be shut down) lspci -vnn | grep -iA5 audio: 00:01.1 Audio device [0403]: Advanced Micro Devices [AMD] nee ATI Device [1002:9902] Subsystem: Hewlett-Packard Company Device [103c:184c] Flags: bus master, fast devsel, latency 0, IRQ 53 Memory at f0444000 (32-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel -- 00:14.2 Audio device [0403]: Advanced Micro Devices [AMD] Hudson Azalia Controller [1022:780d] (rev 01) Subsystem: Hewlett-Packard Company Device [103c:184c] Flags: bus master, slow devsel, latency 32, IRQ 54 Memory at f0440000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel It seems to me that I'm currently running hda Intel drivers on my AMD Hudson Azalia soundcard. I can't see what drivers this soundcard uses. Do I need any additional drivers for my soundcard, and where would I find them?

  Read the article

• How do I solve VirtualBox error 0x80004005?

  - by maria

  Hi I was trying to run Windows XP under Virtual Box (host system Ubuntu 10.04) and I've got an error message saying: Kernel driver not installed (rc=-1908) The VirtualBox Linux kernel driver (vboxdrv) is either not loaded or there is a permission problem with /dev/vboxdrv. Re-setup the kernel module by executing '/etc/init.d/vboxdrv setup' as root. Users of Ubuntu, Fedora or Mandriva should install the DKMS package first. This package keeps track of Linux kernel changes and recompiles the vboxdrv kernel module if necessary. This is terminal output: maria@maria-laptop:~$ sudo /etc/init.d/vboxdrv setup * Stopping VirtualBox kernel modules * done. * Uninstalling old VirtualBox DKMS kernel modules * done. * Trying to register the VirtualBox kernel modules using DKMS * Failed, trying without DKMS * Recompiling VirtualBox kernel modules * done. * Starting VirtualBox kernel modules * done. After that I can run XP on Virtual Box, but when I try to log into user's account, I have the message that I have to register XP (I haven't done it yet, as each time I was cliking on pop-up window suggesting registration, nothing was happening). I click that I want to register it now and appears the message about error 0x80004005, which prevents Windows to check the license for that computer (the message is in Polish, so I don't post it here...). I forgot to install DKMS first, but I've done it after. What should I do to run virtual machine? It was using it already, the problem occured only today. Thanks for any suggestion

  Read the article

• How to re-configure graphics from Intel integrated to Intel / ATI switchable?

  - by Bucic

  There are lots of 'how to get switchable graphics to work' guides but I found none on how to configure a system for switchable graphics operation on Ubuntu from the ground up, nor explaining the current driver situation for particular computer models (integrated+discrete combinations). Example: https://help.ubuntu.com/community/HybridGraphics My system being mature and on Intel integrated card also makes things complicated. System information: Ubuntu 12.04 amd64, installed clean with system configured to use only the integrated Intel card Lenovo Thinkpad T500 Intel GMA 4500MHD / ATI Mobility Radeon HD 3650 Current situation: Mature and up-to-date system with no configuration changes to what's given above. I've made a backup image of the system (Clonezilla) so regardless of what's written below let's assume it's our starting point. If something in What I have already tried is not clear you may as well diregard it. What I have already tried: Configuring BIOS to switchable graphics and: Installing Additional Hardware drivers - returned an error. Installing proprietary amd-driver-installer-12.6-legacy-x86.x86_64.run automatically - system starts to 'low-graphics mode'. Tried fixing as per https://help.ubuntu.com/community/BinaryDriverHowto/ATI#Manually_installing_Catalyst_12.6.2C_special_case_for_Intel.2BAC8-ATI_hybrid_graphics Got lost, gave up. Please note that while configuring BIOS for integrated graphics only is pretty straightforward, configuring for switchable graphics is not.

  Read the article

• wired connection not working in ubuntu 12.04 on lenovo G580 laptop

  - by shravankumar

  I found solution in http://www.zyxware.com/articles/2680/solved-wired-connection-eth0-not-detected-in-ubuntu-12-04 I downloaded compact-wireless-2012-07-03-p.tar.bz2 Here the steps i followed along with output 1. shravankumar@shravankumar-Lenovo-G580:~/Desktop/compat-wireless-2012-07-03-p$ scripts/driver-select alx Output: Processing new driver-select request... Backup exists: Makefile.bk Backup exists: Makefile.bk Backup exists: drivers/net/ethernet/broadcom/Makefile.bk Backup exists: drivers/net/ethernet/atheros/Makefile.bk Backup exists: Makefile.bk Backup exists: Makefile.bk Backup exists: drivers/net/ethernet/broadcom/Makefile.bk 2.shravankumar@shravankumar-Lenovo-G580:~/Desktop/compat-wireless-2012-07-03-p$ make output: make -C /lib/modules/3.2.0-23-generic/build M=/home/shravankumar/Desktop/compat-wireless-2012-07-03-p modules make[1]: Entering directory `/usr/src/linux-headers-3.2.0-23-generic' scripts/Makefile.build:44: /home/shravankumar/Desktop/compat-wireless-2012-07-03-p/drivers/net/ethernet/atheros/alx/Makefile: No such file or directory make[4]: *** No rule to make target `/home/shravankumar/Desktop/compat-wireless-2012-07-03-p/drivers/net/ethernet/atheros/alx/Makefile'. Stop. make[3]: *** [/home/shravankumar/Desktop/compat-wireless-2012-07-03-p/drivers/net/ethernet/atheros/alx] Error 2 make[2]: *** [/home/shravankumar/Desktop/compat-wireless-2012-07-03-p/drivers/net/ethernet/atheros] Error 2 make[1]: *** [_module_/home/shravankumar/Desktop/compat-wireless-2012-07-03-p] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-3.2.0-23-generic' make: *** [modules] Error 2 3. hravankumar@shravankumar-Lenovo-G580:~/Desktop/compat-wireless-2012-07-03-p$ make install output: FATAL: Could not open /lib/modules/3.2.0-23-generic/modules.dep.temp for writing: Permission denied make: *** [uninstall] Error 1 4. shravankumar@shravankumar-Lenovo-G580:~/Desktop/compat-wireless-2012-07-03-p$ modeprobe alx output: No command 'modeprobe' found, did you mean: Command 'modprobe' from package 'module-init-tools' (main) modeprobe: command not found I am new to Ubuntu ,Please help me. Thanks in advance

  Read the article

• Cannot make Wi-Fi hotspot

  - by Junaid

  I want to make my laptop as wi-fi hotspot. To do so, I pressed button Settings-Network-Wireless-Use as Hotspot.. Then it creates a wireless network connection 'Hostspot' and connects. But it gets disconnected just after making connection. Here is my network hardware info: sudo lshw -C network *-network description: Wireless interface product: WiFi Link 5100 vendor: Intel Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: wlan0 version: 00 serial: width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-12-generic firmware=8.83.5.1 build 33692 latency=0 link=no multicast=yes wireless=IEEE 802.11abgn resources: irq:47 memory:d9200000-d9201fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 02 serial: size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=N/A ip=192.168.1.4 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:45 ioport:2000(size=256) memory:d5010000-d5010fff memory:d5000000-d500ffff memory:d5020000-d502ffff My machine is running on Ubuntu 11.10 Can anybody help in it? Thanks

  Read the article

• Cedarview drivers boot to a blank screen

  - by map7

  I'm following the tutorial following tutorial to get my Intel D2700DC motherboard's graphics working: http://daily.siebler.eu/2012/06/ubuntu-12-04-driver-for-intel-cedarview-atom-n2000-und-d2000-serie/ When I boot I'm getting a blank screen. I followed the tutorial and read all the comments. I've also tried: Install gdm and use this instead of lightdm (ubuntu default) sudo apt-get install gdm Remove previous pae kernel: http://www.liberiangeek.net/2011/11/remove-old-kernels-in-ubuntu-11-10-oneiric-ocelot/ Reboot before adding cedarview packages. Have tried with and without the "video=LVDS-1:d" to GRUB_CMDLINE_LINUX_DEFAULT variable in /etc/default/grub I still get a blank screen. I am plugged into a HD screen through the HDMI and have tried the DVI connector also. I can see the grub menu, then a little of the loading and then 'No signal'. I can still ssh into the box though so it is logging in. lspci -v -s 00:02.0 00:02.0 VGA compatible controller: Intel Corporation Atom Processor D2xxx/N2xxx Integrated Graphics Controller (rev 09) (prog-if 00 [VGA controller]) Subsystem: Intel Corporation Device 2011 Flags: bus master, fast devsel, latency 0, IRQ 45 Memory at 80100000 (32-bit, non-prefetchable) [size=1M] I/O ports at 20d0 [size=8] Expansion ROM at <unassigned> [disabled] Capabilities: <access denied> Kernel driver in use: pvrsrvkm Kernel modules: cedarview_gfx uname -a Linux test-desktop 3.2.0-35-generic #55-Ubuntu SMP Wed Dec 5 17:45:18 UTC 2012 i686 i686 i386 GNU/Linux

  Read the article

• VirtualBox error 0x80004005

  - by maria

  Hi I was trying to run Windows XP under Virtual Box (host system Ubuntu 10.04) and I've got an error message saying: Kernel driver not installed (rc=-1908) The VirtualBox Linux kernel driver (vboxdrv) is either not loaded or there is a permission problem with /dev/vboxdrv. Re-setup the kernel module by executing '/etc/init.d/vboxdrv setup' as root. Users of Ubuntu, Fedora or Mandriva should install the DKMS package first. This package keeps track of Linux kernel changes and recompiles the vboxdrv kernel module if necessary. This is terminal output: maria@maria-laptop:~$ sudo /etc/init.d/vboxdrv setup * Stopping VirtualBox kernel modules * done. * Uninstalling old VirtualBox DKMS kernel modules * done. * Trying to register the VirtualBox kernel modules using DKMS * Failed, trying without DKMS * Recompiling VirtualBox kernel modules * done. * Starting VirtualBox kernel modules * done. After that I can run XP on Virtual Box, but when I try to log into user's account, I have the message that I have to register XP (I haven't done it yet, as each time I was cliking on pop-up window suggesting registration, nothing was happening). I click that I want to register it now and appears the message about error 0x80004005, which prevents Windows to check the license for that computer (the message is in Polish, so I don't post it here...). I forgot to install DKMS first, but I've done it after. What should I do to run virtual machine? It was using it already, the problem occured only today. Thanks for any suggestion

  Read the article

• Trying to install Canon iP7250 printer

  - by Chris Burmajster

  I'm trying to install my Canon iP7250 printer on a fresh install of 13:10 64bit. Last time I installed it successfully via http://handytutorial.com/install-canon-printer-driver-for-ubuntu-13-04-12-10-12-04 which entailed adding a repository via the terminal and then updating it. I then opened Synaptic and searched for my printer model and Synaptic then installed everything. This time round I added the repositories but the update failed with the following error: Failed to fetch http://ppa.launchpad.net/michael-gru...amd64/Packages 404 Not Found Failed to fetch http://ppa.launchpad.net/michael-gru...-i386/Packages 404 Not Found Some index files failed to download. They have been ignored, or old ones used instead. An internet search failed to find another way of installing this printer so I'm stuck. My laptop also runs 64 bit 13:10 and the printer works, as I installed it months ago. Is there any way I can take something off that to use on this new machine? Thank you all in advance P.S. I have just found and downloaded the official Canon driver from the Canon website and extracted it, but I don't know how to install it.

  Read the article

• How to install compat-drivers or compat-wireless

  - by Sasho

  Could someone please explain me in detail how to install some of this drivers. I am running Ubuntu 12.04.2 and have the infamous (as I see everywhere in the net) problem with Atheros AR9462 wifi card. I tried everything to fix it and compat drivers are the only solution that I haven't tried. I tried to install some random package from kernel.org site and it couldn't make the driver (it threw some error). Then I updated the kernel to 3.10-rc7 and downloaded the last release of compat drivers and again the same problem occured. I reinstalled Ubuntu 12.04.2 and now I am using the 3.5 kernel because I don't know if rc7 is stable version. So my question is which compat wireless or compat drivers to download for this kernel and what is the process of installing. I tried with some command from the repository and it returned that it's not found. PS I am new to Ubuntu and Linux in general so explaining at length the install process and which driver I should install would be appreciated.

  Read the article

• Compiz not drawing window controls in ubuntu 11.10

  - by Siva Prasad Varma

  I have recently installed driver for my ATI graphic card in my Dell Studio laptop. I have also read this somewhere on the web that Ubuntu enables compiz window manager by default if your hardware can run it. Is it true ? In my case before Installing graphic card driver the window manager was Metacity, but now I have compiz as my Window manager. I found this out uisng Displex Indicator applet also confirmed by wmctrl -m. From the time I have installed graphic card drivers, the window manager(Compiz) is not drawing window control buttons for some of the windows. For example if I open a terminal I have to close it using key board shortcuts or use the File - Quit option in app-menu. Also I am not able to move the window because of this. From then when-ever I find a window without window control buttons I am restarting the window manager using Displex Indicator applet. But this is very annoying and also consumes a lot of time(when I am doing my work). Can any one suggest any solution for this. What are up's and down's of using Compiz Vs Metacity.

  Read the article

• Firefox 12's hardware acceleration on Ubuntu 12.04 LTS

  - by user64943

  After I have installed Ubuntu 12.04 LTS (32 bits), Firefox 12 works fine but without hardware acceleration. Needless to say I have the latest nVidia's proprietary drivers installed and my Firefox Preferences, on "Advanced" tab, "Browsing" section, have the option "Use hardware acceleration when available" checked. I have tried the following things before asking this question: Creating a boolean key "webgl.force-enabled" and set it to true on Firefox's page about:config; Starting a new profile like commented on thread Mozilla Firefox 12 is very slow on Ubuntu 12.04 LTS; I have updated my nVidia driver to version 295.53. And none of this have worked. As you can see below in my Firefox's page about:support report, "Graphics" section shows no "GPU Accelerated Windows": Adapter Description NVIDIA Corporation -- GeForce GTX 460/PCIe/SSE2 Vendor ID NVIDIA Corporation Device ID GeForce GTX 460/PCIe/SSE2 Driver Version 4.2.0 NVIDIA 295.53 WebGL Renderer NVIDIA Corporation -- GeForce GTX 460/PCIe/SSE2 -- 4.2.0 NVIDIA 295.53 GPU Accelerated Windows 0 AzureBackend skia I use the following site to test hardware acceleration: http://ie.microsoft.com/testdrive/Performance/FishBowl/ On Windows 7 I get 60 fps even with 1,750 fishes on browser's Full Screen Mode (1680x1050x32bit-color). On Ubuntu 12.04 LTS, same nVidia drivers (as shown in report), won't go faster than 15 fps with only 1,000 fishes. Can anybody help me? Best Regards,

  Read the article

• Why can't I run Compiz?

  - by jasoncruz98

  I installed Ubuntu 11.10 on my laptop. The main reason I switched to Ubuntu is because I wanted to use Compiz. The first thing I did was to go to Additional Drivers and install ATI/AMD Proprietary FGRLX Graphics Driver. There was also another one available, ATI/AMD Proprietary FGRLX Graphics Driver (post-release updates), but I didn't install that one, because it basically meant the same thing to me as the one I already installed. Next, I went to the ubuntuguide.org Oneiric Wiki http://ubuntuguide.org/wiki/Ubuntu:Oneiric#Compiz_Fusion So I followed the instructions there and ran this command in terminal: sudo apt-get install compiz compizconfig-settings-manager compiz-fusion-plugins-main compiz-fusion-plugins-extra emerald librsvg2-common But then, the terminal window said that the package "emerald" could not be found. So, I ran this command instead: sudo apt-get install compiz compizconfig-settings-manager compiz-fusion-plugins-main compiz-fusion-plugins-extra After that, I installed Fusion Icon by running this command: sudo apt-get install fusion-icon I restarted my computer, searched for Compiz Config Settings Manager, and clicked on it. Then, I activated Wobbly Windows. I logged off and logged back on again, but there was no wobbly windows effect. So I tried clicking on Fusion Icon, but it never started. Can someone please tell me what I did wrong here? Because I see everyone seems to be able to run Compiz except me. I really need to start Compiz, or else I think I'm going to uninstall Ubuntu.

  Read the article

• Network really slow with TL-WN951N wireless card

  - by Sam

  I literally just installed ubuntu and it seems to be working great except the network is deadly slow. I'm running a TL-WN951N wireless card which can download at about 600-700 KB/s in windows but in Ubuntu the max speed it seems to get is around 5KB/s. I guess I should note that my WAP is only wireless-G but like I said, I can get much better speeds in Windows. I'm testing the speeds by downloading files from here: http://mirror.internode.on.net/pub/test/ Anyone have any idea? I saw some people recommend downloading drivers and compiling them myself but I'm really really new to all of this so would appreciate someone babying me through it so I don't brick my computer! Here are the results of lspci -v: 04:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02) Subsystem: Giga-byte Technology GA-EP45-DS5 Motherboard Flags: bus master, fast devsel, latency 0, IRQ 44 I/O ports at c000 [size=256] Memory at e9110000 (64-bit, prefetchable) [size=4K] Memory at e9100000 (64-bit, prefetchable) [size=64K] [virtual] Expansion ROM at e9120000 [disabled] [size=64K] Capabilities: <access denied> Kernel driver in use: r8169 Kernel modules: r8169 05:02.0 Network controller: Atheros Communications Inc. AR5008 Wireless Network Adapter (rev 01) Subsystem: Atheros Communications Inc. Device 3071 Flags: bus master, 66MHz, medium devsel, latency 168, IRQ 18 Memory at e9200000 (32-bit, non-prefetchable) [size=64K] Capabilities: <access denied> Kernel driver in use: ath9k Kernel modules: ath9k

  Read the article

• Spring Roo Database Reverse Engineer with Oracle

  - by kerry

  So you are trying to reverse engineer an Oracle database with roo? Unfortunately, due to licensing restrictions with the Oracle JDBC Drivers, this is a little difficult. There are a few blog posts and forum threads that address the problem but I figured I would post what worked for me here. First, you need to download the appropriate Oracle Drivers from Oracle. The required login, stringent password requirements, nosy registration form, and general system instability made this a pretty painful step for me. I’d also like to say that companies that have password requirements that don’t allow symbols (or any other non-standard requirement) have a special place in my heart. Having to recover my password every time I go to your site virtually guarantees I will only go there when I absolutely have to (not often). Anyways, once you have it downloaded you need to install is with maven: mvn install:install-file -Dfile=~/Downloads/ojdbc6.jar -DgroupId=com.oracle -DartifactId=ojdbc6 -Dversion=11.2.0.3 -Dpackaging=jar -DgeneratePom=true Here comes the fun part. You need to create an osgi wrapper for the driver to install it in roo. Otherwise, roo cannot see the driver. Create a new folder and put the contents of the oracle roo addon pom gist I created. Now build it with maven. You may want to change some of the artifact ids and dependencies for your particular situation. mvn package No open a roo shell and execute the following command: osgi install --url file:///Users/me/my-osgi-project/target/the-jar-it-built.jar Now run (in roo): jpa setup --provider HIBERNATE --database ORACLE dependency remove --groupId com.oracle --artifactId ojdbc14 --version 10.2.0.2 dependency add --groupId com.oracle --artifactId ojdbc6 --version 11.2.0.3 database properties set --key database.driverClassName --value oracle.jdbc.OracleDriver database properties set --key database.url --value jdbc:oracle:thin:@%YOUR_CONNECTION_INFO% database properties set --key database.username --value %YOUR_USERNAME% database properties set --key database.password --value %YOUR_PASSWORD% database reverse engineer --schema %YOUR_SCHEMA% --package ~.domain If you have any package loading exceptions when running the reverse engineer command you can uninstall the osgi bundle, set the package to optional in the osgi pom in the IncludedPackages tag (javax.some.package.*;resolution:=optional) rebuild, then reinstall in roo.

  Read the article

• .wine-pipelight folder not present

  - by DaimyoKirby

  Following the instructions on the pipelight installation page, I installed pipelight on Ubuntu 14.04. However, upon opening firefox the .wine-pipelight folder isn't present in my home folder, and I get the following errors: [PIPELIGHT:LIN:unknown] attached to process. [PIPELIGHT:LIN:unknown] checking environment variable PIPELIGHT_SILVERLIGHT5_1_CONFIG. [PIPELIGHT:LIN:unknown] searching for config file pipelight-silverlight5.1. [PIPELIGHT:LIN:unknown] trying to load config file from '/home/alden/.config/pipelight-silverlight5.1'. [PIPELIGHT:LIN:silverlight5.1] basicplugin.c:427:checkSilverlightGraphicDriver(): error in execlp command - probably silverlightGraphicDriverCheck not found or missing execute permission. [PIPELIGHT:LIN:silverlight5.1] basicplugin.c:441:checkSilverlightGraphicDriver(): GPU driver check - Your driver is not in the whitelist, hardware acceleration disabled. [PIPELIGHT:LIN:silverlight5.1] using wine prefix directory /home/alden/.wine-pipelight. [PIPELIGHT:LIN:silverlight5.1] checking plugin installation - this might take some time. [PIPELIGHT:LIN:silverlight5.1] basicplugin.c:374:checkPluginInstallation(): error in execvp command - probably dependencyInstaller/sandbox not found or missing execute permission. [PIPELIGHT:LIN:silverlight5.1] basicplugin.c:384:checkPluginInstallation(): Plugin installer did not run correctly (exitcode = 1). [PIPELIGHT:LIN:silverlight5.1] basicplugin.c:108:attach(): plugin not correctly installed - aborting. I've reinstalled quite a few times and ran through many of the common fixes offered on the pipelight Launchpad pages and here on AskUbunta and still it fails to run. Is there a reason why this folder isn't present, or why I'm getting these errors? Edit: Oddly enough, the .wine-pipelight folder is created wtih I open Nitro, although this still doesn't fix the issue.

  Read the article

• Gnome-Network-Manager Config File Migration

  - by Jorge

  I think I have an issue with gnome-network-manager, I used to have a lot of connections configured, Wireless, Wired and VPN. After upgrading to 12.04 (from 11.10) I lost every configuration. I realized that the configs that used to be saved in $HOME/.gconf/system/networking/connections now are being saved in /etc/NetworkManager/system-connections/. I don't know how to migrate my settings to the new config file format Can anybody help me? jorge@thinky:~$ sudo lshw -C network *-network description: Ethernet interface product: 82566MM Gigabit Network Connection vendor: Intel Corporation physical id: 19 bus info: pci@0000:00:19.0 logical name: eth0 version: 03 serial: 00:1f:e2:14:5a:9b capacity: 1Gbit/s width: 32 bits clock: 33MHz capabilities: pm msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e1000e driverversion=1.5.1-k firmware=0.3-0 latency=0 link=no multicast=yes port=twisted pair resources: irq:46 memory:fe000000-fe01ffff memory:fe025000-fe025fff ioport:1840(size=32) *-network description: Wireless interface product: PRO/Wireless 4965 AG or AGN [Kedron] Network Connection vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 61 serial: 00:21:5c:32:c2:e5 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwl4965 driverversion=3.2.0-23-generic-pae firmware=228.61.2.24 ip=192.168.2.103 latency=0 link=yes multicast=yes wireless=IEEE 802.11abgn resources: irq:47 memory:df3fe000-df3fffff jorge@thinky:~$ lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 12.04 LTS Release: 12.04 Codename: precise jorge@thinky:~$ uname -a Linux thinky 3.2.0-23-generic-pae #36-Ubuntu SMP Tue Apr 10 22:19:09 UTC 2012 i686 i686 i386 GNU/Linux jorge@thinky:~$ dpkg -l | grep -i firm ii linux-firmware 1.79 Firmware for Linux kernel drivers

  Read the article

• Ralink RT3060 wireless device configuration on ubuntu 12.04

  - by Stephan

  concerning How do I get a Ralink RT3060 wireless card working? I'm running Ubuntu 12.04 with a 'LWPX07 Edimax EW-7711In 150M 1T1R WL PCI Card' which has a rt3060 chip. Out of the box the card is recognized as rt2800sta. I tried solution one, that didn't work. Still the card connects to the wireless network, but it seems to slow to load any pages. Then I tried solution 2, but then the network-manager doesn't see any wireless device. $ iwconfig lo no wireless extensions. ra0 Ralink STA Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 invalid crypt:0 invalid misc:0 eth0 no wireless extensions. $ lsmod Module Size Used by rt3562sta 882296 0 $ lspci -v 05:02.0 Network controller: Ralink corp. RT3060 Wireless 802.11n 1T/1R Subsystem: Edimax Computer Co. Device 7711 Flags: bus master, slow devsel, latency 64, IRQ 23 Memory at ff9f0000 (32-bit, non-prefetchable) [size=64K] Capabilities: <access denied> Kernel driver in use: rt2860 Kernel modules: rt3562sta, rt2800pci Am I missing a configuration step? How do I tell the network card which driver to use? Thanks in advance Stephan I found the problem. As described in stevens blog http://steveswinsburg.wordpress.com/2011/03/12/how-to-install-a-d-link-dwa-525-wireless-network-card-in-ubuntu-10-04/ sudo su make && make install "You need to use ‘sudo su’ and not just ‘sudo’ so it creates the directories properly." That is the problem with the solution describe above.

  Read the article

• Qualcomm Gobi WWAN modem no longer appears in Network Manager

  - by Andy E

  Not sure what happened here. I installed Cinnamon on my Ubuntu 12.10 environment yesterday, rebooted when finished and everything was working fine. I even used my WWAN modem after my fixed line broadband went down. However, after starting my machine this morning and seeing that my fixed line is still having problems (intermittently), I clicked the network applet and my WWAN device wasn't listed. It's not in the main network manager window either. It is still present on the system, however: $ lsusb Bus 001 Device 003: ID 05ca:18b0 Ricoh Co., Ltd Sony Vaio Integrated Webcam Bus 001 Device 004: ID 05c6:9221 Qualcomm, Inc. Gobi Wireless Modem (QDL mode) Bus 002 Device 005: ID 04e8:6865 Samsung Electronics Co., Ltd Bus 002 Device 002: ID 0409:005a NEC Corp. HighSpeed Hub Bus 003 Device 002: ID 147e:1000 Upek Biometric Touchchip/Touchstrip Fingerprint Sensor Bus 008 Device 002: ID 044e:3017 Alps Electric Co., Ltd BCM2046 Bluetooth Device Debug output from modem-manager, refers to a device that is blacklisted: modem-manager[10186]: [1355478137.024491] [mm-manager.c:866] device_added(): (tty/ttyUSB0): port's parent device is blacklisted modem-manager[10186]: [1355478137.024607] [mm-manager.c:875] device_added(): (tty/ttyS0): port's parent platform driver is not whitelisted modem-manager[10186]: [1355478137.024700] [mm-manager.c:875] device_added(): (tty/ttyS1): port's parent platform driver is not whitelisted ... I couldn't see anything relevant in the debug output for network-manager, but I've created a paste for it just in case. In /lib/udev/rules.d/77-mm-qdl-device-blacklist.rules, I found the following line that matches the device IDs from the lsusb output: # Generic Gobi QDL device ATTRS{idVendor}=="05c6", ATTRS{idProduct}=="9221", ENV{ID_MM_DEVICE_IGNORE}="1" I tried commenting out the second line and restarting network-manager/modem-manager but it didn't help. I've no idea where to go from here, does anyone else have any ideas?

  Read the article

• Restore audio settings - cannot open mixer: No such file or directory

  - by Alfred M.

  The internal speaker of my laptop never functionned under Ubuntu. I tried to follow indication on the web and now the jack audio does not work either. The graphic interface for audio management now displays a 'dummy output' instead of the three possible outputs I used to have (one of them was working for the jack output). In a terminal alsamixer raises an error: cannot open mixer: No such file or directory I did try to remove and reinstall alsa-utils but it did not change anything. This happened after a failed atempt to install alsa-driver-linuxant_1.0.23.1_all.deb from here. My sound card seems to be not recognised anymore. After reboot I have no more the sound icon in menu bar the upper right corner. I think I have removed my sound card driver. Indeed, the command sudo lshw -class multimedia indicated audi device as unclaimed. Any idea how I could revert to a better situation (that is jack support and alsa working)? EDIT: The command lspci -nnk | grep -iEA3 audio gives lspci -nnk | grep -iEA3 audio 00:1b.0 Audio device [0403]: Intel Corporation 82801I (ICH9 Family) HD Audio Controller [8086:293e] (rev 03) Subsystem: ASUSTeK Computer Inc. Device [1043:1893] 00:1c.0 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 [8086:2940] (rev 03)

  Read the article

• Dot Matrix printers setup...

  - by Parhs

  Hello! I am using debian which is similar to ubuntu. They have 7 dot matrix printers some very old like this one http://www.omnidatasys.net/product/desc_printer_ti880.htm which works from 1979 daily and at text is faster than many inkjects. I believe that it has his own language... Sending text to serial port (port server) prints garbage. However i think is prints only capital english up to 95 asccii and greek and the rest up to 127 i think greek capital.(special chip ) Sending english capital letters prints garbage i think but i amnt sure... i will try again... The other printer are ESC/P compatible and i use generic epson driver provided from ghostscript... However i think that sending text via lp -dpr1 filename It prints the text as a grafic...Changing from printer font face(courier,times roman etc) or pitch has no effect... I am wondering if is there any work arround for this? In AIX they claim that lp command printed output as text as it prints and cobol programs send raw text to to lp printers . However in AIX they use some custom filters for the printers and has more options for dot matrix printers.. I would like to know if there is a solution for this.. To avoid graphics mode for text and change font face somehow.. The most Straight-through approach would be to use no driver ,just send ESC/P from cobol but this requires too much work... Thank you again!

  Read the article

• How to fix E: Internal Error, No file name for libc6

  - by Loren Ramly

  How to fix E: Internal Error, No file name for libc6, Like that will show If I do: $ sudo apt-get upgrade or $ sudo apt-get install package This is example : $ sudo apt-get upgrade Reading package lists... Done Building dependency tree Reading state information... Done The following packages have been kept back: ginn hplip hplip-data libdrm-dev libdrm-intel1 libdrm-nouveau1a libdrm-radeon1 libdrm2 libgrip0 libhpmud0 libkms1 libsane-hpaio libunity-2d-private0 libunity-core-5.0-5 linux-generic-pae linux-headers-generic-pae linux-image-generic-pae printer-driver-hpcups printer-driver-hpijs unity unity-2d-common unity-2d-panel unity-2d-shell unity-2d-spread unity-common unity-services The following packages will be upgraded: alsa-base firefox firefox-globalmenu firefox-gnome-support firefox-locale-en icedtea-6-jre-cacao icedtea-6-jre-jamvm icedtea-7-jre-jamvm libdbus-glib-1-2 libdbus-glib-1-dev libgnutls-dev libgnutls-openssl27 libgnutls26 libgnutlsxx27 libssl-dev libssl-doc libssl1.0.0 linux-sound-base openjdk-6-jre openjdk-6-jre-headless openjdk-6-jre-lib openjdk-7-jdk openjdk-7-jre openjdk-7-jre-headless openjdk-7-jre-lib openssl sudo 27 upgraded, 0 newly installed, 0 to remove and 26 not upgraded. 3 not fully installed or removed. Need to get 0 B/126 MB of archives. After this operation, 3,072 B of additional disk space will be used. Do you want to continue [Y/n]? y E: Internal Error, No file name for libc6 I have follow instruction from here E: Internal Error, No file name for libssl1.0.0 . Which do: sudo apt-get update sudo apt-get clean sudo apt-get install -fy sudo dpkg -i /var/cache/apt/archives/*.deb sudo dpkg --configure -a sudo apt-get install -fy sudo apt-get dist-upgrade But stuck with same error E: Internal Error, No file name for libc6 when do command sudo apt-get install -fy. And I've been looking on google, but have not been successful until now. Thanks.

  Read the article

• Hybrid Graphics on Windows 7/Ubuntu 12.04 Dual Boot

  - by Noob.

  Alright, so here's the situation: I am using an ASUS UL80VT with two graphics cards: Integrated intel graphics and NVIDIA G210M I was running an Ubuntu 12.04 - Windows 7 dual boot (on separate partitions).The machine worked perfectly (including the display drivers) without me needing to install anything special or change any settings. However, my hard drive was corrupted and I lost all my data yesterday, so after it was replaced, I installed Ubuntu 12.04 64x again after installing Windows 7. I booted up Ubuntu after installation, and noticed it was by default using Unity 2D... Gnome 3.4 wasn't working properly either, so I guessed that the NVIDIA G210M driver wasn't installed/working and the OS was instead using the integrated graphics. I checked the "Additional Drivers" thing, but there were no proprietary drivers listed there, so I went to the NVIDIA website, downloaded the driver directly and installed it. I restarted, but there was no change. After this, I read somewhere that I should change my SATA in the BIOS to "Compatible" rather than "Enhanced". This worked fine and fixed the problem (both Unity and Gnome were working perfectly) but then when I tried booting up Windows 7, I recieved the BSOD. So I changed it back to Enhanced, and once again, the NVIDIA 210M graphics isn't working on Ubuntu, but on Windows 7 it is. I do not want to keep changing from Enhanced to Compatible every time I reboot to Ubuntu and neither do I want to simply just use one OS. Note that NVIDIA 210M and integrated graphics work perfectly on Windows 7. Also, I don't care about switching between them, I just want to be able to use the NVIDIA one. What can I do so that both Windows 7 and Ubuntu work and NVIDIA G210M works on Ubuntu?

  Read the article

• two possible wifi devices competing, one is hard blocked - unable to connect wireless

  - by patrickmw

  blacklisted acer_wmi because that was showing up in the rfkill list then ideapad_wlan was listed $ rfkill list wifi 1: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 3: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes $ lshw -C network *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Atheros Communications physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: c0 serial: f0:de:f1:12:21:e9 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI duplex=full firmware=N/A ip=192.168.1.139 latency=0 link=yes multicast=yes port=twisted pair speed=1Gbit/s resources: irq:42 memory:f0400000-f043ffff ioport:2000(size=128) *-network description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: eth1 version: 01 serial: ac:81:12:38:ba:89 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:f0500000-f0503fff contents of /var/lib/NetworkManager/NetworkManager.state [main] NetworkingEnabled=true WirelessEnabled=true WWANEnabled=true I'm not sure how to disable the wifi devices independently. I'm also not sure which device is the correct one. I think its the brcmw device. Any suggestions?

  Read the article

• Xubuntu 14.04 with Compton, strange screen tearing, only when playing videos though (advice needed)

  - by LinuxDudester

  Hello beloved community, Yet again I am in need of your great expertise. I ran into a very strange issue and just can't wrap my mind around it. I'm running Xubuntu 14.04 exclusively, with Compton installed. The OS runs great and I have absolutely no screen tearing when I move my windows around, scroll in my web browser, work in Gimp or Photoshop (wine) or even when I play very graphic demanding games, like Metro Last Light, Euro Truck Driver 2 and so on. There's not a tiny bit of tearing to see, but as soon as I play videos, in xbmc, vlc or parole media player the tearing begins (strangely enough this does not apply to youtube videos). I followed all available workarounds on askubuntu and the ubuntu forum,like the 50-xserver-command.conf, startx /etc/X11/Xsession /usr/bin/xbmc-standalone -- -bs or libsdl1.2debian fix and many more, but to no avail. I also tried the Open Source Nouveau display drivers as well, but for some odd reason they don't work so great on my system or at least with my graphics card. Even with Compton installed and configured, I have an extreme amount of screen tearing, as soon as I switch to the proprietary Nvidia drives the screen tearing is gone completely, except for the video playback with xbmc, vlc or parole media player. System info for your reference: OS: Xubuntu 14.04 Linux-x86_64 - Processor: Intel Core i7-4770S CPU @ 3.10GHz - Ram: 16 GB - GeForce GT 750M 1024 MB - Nvidia Driver: 331.38 Has anyone experienced such an odd issue or do you have any advice on how I could fix this? I would appreciate any help! Have a nice day!

  Read the article

< Previous Page | 191 192 193 194 195 196 197 198 199 200 201 202  | Next Page >