Search Results

Search found 12028 results on 482 pages for 'drive letters'.

Page 197/482 | < Previous Page | 193 194 195 196 197 198 199 200 201 202 203 204  | Next Page >

  • Disk Image Tools for Windows Server 2008

    - by Jon Rauschenberger
    I have a Windows Server 2008 X64 machine that I need to swap the boot drive on. I'd like to use a disk image/restore utility to make an image of the boot partition and restore that to the new drive. Does anyone know of a free or reasonably priced tool that can do this? I know that Acronis True Image will do it, but you need to have their server product to restore images of a server OS and it's prohibitively expensive ($850). Thanks, jon

    Read the article

  • missing files after reassemble of RAID-5

    - by Kris_R
    I had to open my file-server's housing on Sunday to replace a faulty fan. What I didn't see was that one of the sata-cables was not properly connected. The 1st thing I did after a reboot was a check of the RAID status and it showed immediately that one drive is missing. Till this moment the device was not used (however it was mounted, so I'm not 100% sure that system did nothing). I stopped md0 and re-plugged the cable: mdadm --stop /dev/md0 poweroff After another reboot I checked the removed drive: mdadm --examine /dev/sdd1 ... Checksum : 3276bc1d - correct Events : 315782 Layout : left-symmetric Chunk Size : 32K Number Major Minor RaidDevice State this 0 8 49 0 active sync /dev/sdd1 0 0 8 49 0 active sync /dev/sdd1 1 1 8 65 1 active sync /dev/sde1 2 2 8 33 2 active sync /dev/sdc1 3 3 8 17 3 active sync /dev/sdb1 I was a bit surprised that it was shown as active (even if earlier mdadm said, that this device was removed from array) and its checksum was OK. I recreated RAID with: mdadm --assemble /dev/md0 --scan The command mdadm --detail /dev/md0 showed that all drives were running and system was in "clean" state. I mounted the device md0 and then came hic-cup. I wanted to work on one of the last files that I had been using before all the situation and it was not there. In another place I missed actually all files from the directory where I was working. As far as I can see most of the files that are older than a few days are intact but some newer ones are missing. Now the big question: what would be your advice? Is there a way to get these data? I thought about removing the drive that was earlier labeled by mdadm and rebuild array with another empty HDD. I've found that after re-assemble the "broken" drive has another label (changed from sdd to sdb). Can this have influence on rebuilt process? If yes, how to reassemble the array properly? I'm sure the SATA-cables are connected still in the same order to the controller. p.s. Please no advises like "restore from backup". I'm doing back-ups on Sunday's night and this happened in the late afternoon, so backup is not really options for me. p.s.s. I asked this question on Unix&Linux but no answer came up during last two days. I'm getting quite anxious. Sorry for duplicating if any of you reading the other forum.

    Read the article

  • pci-express ssd running an OS

    - by tom
    Hi, Simple question really, is it possible to install an OS such as windows or ubuntu on a PCI-Express SSD (solid state drive)? And if so is it as straight forward as selecting that drive on install? Thanks Tom

    Read the article

  • Windows Server 2008 and eSata External Connection

    - by Tyler
    Can anyone recommend a good eSATA PCIe card for Windows Server 2008 (x64)? I bought a J-Micron JMB363 and it's recognized by the OS and I can install one of their reference drivers, but it's not picking up the drive I have attached to it. Basically, I want to be able to transfer exported Hyper-V machines quickly to an external drive, and it seems that using one of these eSATA cards is the way to go.

    Read the article

  • Windows Backup (2008 R2) recovery and timezone

    - by GrZeCh
    Hello, does difference between timezones on Windows Server 2008 where backup was made and reovery console makes difference? Recovery console (wbadmin from command line too) is not finding any backup on local hard drive connected to server. Thanks EDIT: I'm working on Windows Server 2008 R2 EDIT2: This is not related to timezone. When I connected backup hard drive from Windows 2008 R2 Release Candidate recovery console runned from RTM system version DVD found stored backups from it without problems.

    Read the article

  • How to restore a VirtualBox image given the .vdi file

    - by Ramon Tayag
    Background I have VirtualBox on Linux and recently the drive with the system files failed on me. I'm able to use the Live CD to view the files of the storage drive, and through this, I can copy my data files to another computer while I work on this one. How do I load the .vdi in another computer (or in this case, the fresh install of Ubuntu)? I see many samples online of how to export it, but it assumes the host is currently working. Thanks!

    Read the article

  • Disc2vhd and partitions question

    - by dotnetdev
    Hi, I am using Disc2Vhd to make a vhd of my drive. Does the tool support partitions? My partitions of C:\ are listed as both drives and volumes. In short, is there any issue when I select both partitions that make one physical drive? Thanks

    Read the article

  • chkdsk, SeaTools, and "does not have enough space to replace bad clusters"

    - by Zian Choy
    When I tried to do a Windows Vista Complete PC Backup, I received an error message that blathered about bad sectors. Then, when I ran chkdsk /r on the destination drive, this is what I got: C:\Windows\system32>chkdsk /R E: The type of the file system is NTFS. Volume label is Desktop Backup. CHKDSK is verifying files (stage 1 of 5)... 822016 file records processed. File verification completed. 1 large file records processed. 0 bad file records processed. 0 EA records processed. 0 reparse records processed. CHKDSK is verifying indexes (stage 2 of 5)... 848938 index entries processed. Index verification completed. 0 unindexed files processed. CHKDSK is verifying security descriptors (stage 3 of 5)... 822016 security descriptors processed. Security descriptor verification completed. 13461 data files processed. CHKDSK is verifying file data (stage 4 of 5)... The disk does not have enough space to replace bad clusters detected in file 239649 of name . The disk does not have enough space to replace bad clusters detected in file 239650 of name . The disk does not have enough space to replace bad clusters detected in file 239651 of name . An unspecified error occurred.f 822000 files processed) Yet, when I ran the SeaTools short & long generic tests on the Seagate disk, I didn't receive any errors. I know that I could reformat the disk and try running chkdsk /r again but I'd prefer to avoid waiting 4 hours in the hope that the problem was magically fixed. On the other hand, if I RmA the drive to Seagate, I have no SeaTools error number to use and they may claim that the drive is just fine. What should I try to do next? Side frustration: There is plenty of free hard drive space. The E: partition has 182 GB free.

    Read the article

  • Macrium Reflect Recovery Linux Recovery Disc hangs up on booting

    - by user8583
    I created an image of my system with macrium reflect freeware program and stored the image on an usb external hard drive. However the macrium reflect linux recovery disc on startup hangs up of the first three lines of instructions and therefore I cannot access the image on the usb external hard drive if I wish to recover my system. I have a Lenovo laptop with the Windows-7 Home Premium operating system. What can be done to ensure that the recovery disc will work?

    Read the article

  • How to restore using DriveImage XML image if unable to make a BartPE CD

    - by CChriss
    I have a Windows Vista laptop that won't boot at all. On the D: drive I have DriveImage XML images of C: drive, but I don't have a BartPE boot CD and I don't have a Vista install CD. How can I image the C: using the images on D: if I can't make a BartPE CD because I can't boot to Windows? Is there a BartPE (with DriveImage XML plugin) iso I can download from somewhere, or what can I do? Thanks.

    Read the article

  • Make backup image (.tib/.vhd) as my main operating system?

    - by Joann
    My old hard drive is dying so I want to move my Windows 7 operating system to another hard drive. They say cloning using Acronis would do the trick, but for some reason it refuses to work. I also tried EASEUS Todo Backup, but it doesn't work either. Can you recommend some suggestions on how to transfer my operating system? I heard about converting .tib to .vhd and then booting from it, but does that achieve the same effect as cloning?

    Read the article

  • How to save QuickTime movie trailer files?

    - by Jian Lin
    Is it true that a few months ago, QuickTime allows users to save the movie trailers without using the Pro version? Right now, it seems like we need to pay $29.99 to save the movie trailer clip onto the hard drive... Several months ago, I also tried using Ubuntu and there was a plugin to view the movie trailer and was able to save it too... Are there other ways to save it to the hard drive?

    Read the article

  • What's the best way to move c:\users to d:\users under vista/W7

    - by Scott
    I just installed Windows 7 RC1 and want to move c:\users to d:\users. What's the best way to do this? Due to the fact that Windows 7 creates a reserved partition that is mounted as C: in the recovery console, I had to use the following commands robocopy /mir /xj D:\Users E:\Users mklink D:\Users D:\Users /j Both D's in the mklink command are correct. When the system reboots, the drive that was D in the recovery console becomes the C drive.

    Read the article

  • 0x0000007b vista harddrive swap

    - by unknown (google)
    I swap my hard drive to a new computer with vista 32 I get 0x0000007b stop error on bootup I tried using the cd to do the repair but it fails. I think it is because I have the wrong hard drive driver install for vista or it is missing. How can I fix this from the command line

    Read the article

  • Cannot make BartPE CD - how restore DriveImageXML image?

    - by CChriss
    I have a Windows Vista laptop that won't boot at all. On the D: drive I have DriveImage XML images of C: drive, but I don't have a BartPE boot CD and I don't have a Vista install CD. How can I image the C: using the images on D: if I can't make a BartPE CD because I can't boot to Windows? Is there a BartPE (with DriveImage XML plugin) iso I can download from somewhere, or what can I do? Thanks.

    Read the article

  • OSX Samba Server

    - by Chris Maness
    Hello I have a MacPro that I'm using as a local file server. I mapped a directory on the secondary hard drive of the MacPro as a drive on our local Windows box. It worked fine for about a week and then suddenly stopped working. The windows computer gives the error that it's an invalid username and password however I have checked and double checked to ensure that the user and pass are correct to no avail. Anyone have any ideas on what's going on here?

    Read the article

  • Why do I have multiple drives in my backup system image?

    - by bebop
    I have a drive which has 2 partitions. One is where the OS is installed, the other is a data (but not libraries) drive. When I try and create a backup using the built in tool, it wants to include both partitions in the system image. Why does it do this? If I move the os to a separate drive will I be able to back up just this data? Edit: To be more clear. I have 4 disks in the machine. 1 disc has 2 partitions. These are c: and e:, the other disks are d: f: and h:. The OS is installed on c: and libraries are stored on h:. The libraries are already backed up using crashplan, but I want to create a system image so I can easily restore the machine, if it either dies or if I get a SSD drive. When I choose backup (either through the wizard or if I open it through control panel) and check (or click) create a system image it automatically adds both c: and e: to the list of drives that will be backed up, and I cannot change this, the checkboxes to unselect are greyed out. I would like to know why it automatically adds e: to the list (but not h:, where the libraries are) and if I can change some setting so whatever files it has on e: that it thinks need to be backed up as part of the system image are moved to c:. How can I determine what they are? Is it because c: and e: are partitions of the same disk? If I move c: tro a different disk will that mean I only have to back up c:? Thanks Edit 2: I have viewed all files including hidden and system ones on both drives and it seems that I have a suspicous hidden e:\boot\ folder. I think that I might have installed the OS as a VHD at first then installed a seperate version straight on the disk, having dual boot for a while, then used EasyBCD to remove the VHD boot and file. Might this be what is causing my issue? How might I go about removing this? is it safe to just delete the boot folder?

    Read the article

  • "Error loading operating system": Win7/Vista

    - by LookitsPuck
    Have this computer for about 2 years now. Originally had Vista installed, now have Windows 7 installed. Both on separate hard drives. Also have another drive used strictly for media. About a week ago, the Vista hard drive started going on its way out. Was getting problems on startup. After a few BIOS settings, I was able to get into Windows 7 and everything was fine. However, I started remembering the startup issues, so I deleted the bootup for Vista under msconfig. Didn't restart the computer at that time, though. For a few days, everything was ok. Last night I play a little poker, then hit the hay. I wake up to a good ole "Error loading operating system" on the screen. Just wonderful. Looks like the computer restarted overnight (auto updates, anyone?). So, after a big of finagling and half hearted tries, I can't get past the "Error loading operating system" screen. FWIW, in the BIOS it can see my hard drives fine. So I move on. I get my Windows 7 installation disk to try and do a repair. Go in the BIOS, change boot priority to DVD drive, and we're on our merry way. After loading from the disc, I first try jumping into the "Repair your computer" section. That opens up the System Recovery Options. However, this is where the problem comes into play. I don't see any operating systems here. Nada. What's odd though is if I click on the Load Drivers button, I can see my Windows 7 partition (C:), and can go through the files and folders without issue. What do I do at this point? I can't repair it. It seems like I can traverse the hard drive without issue when in an open dialog in the System Recovery Options, but I'm getting the good ole "Error loading computer" on bootup. Suggestions? Thanks all!!

    Read the article

  • Can't write to raid on Fedora

    - by 99miles
    I just did a fresh install of Fedora 11 and added Raid 1 following this tutorial: http://www.optimiz3.com/installing-fedora-11-and-setting-up-a-raid-0-1-5-6-or-10-array/ Now I see the filesystem when I open 'Computer' in the GUI, and I open it and see 'lost+found', but i can't write to the drive. The option is simply greyed out. And when I view Properties on the drive and go to Permissions, it says 'The permissions of {driveid} could not be determined.' Any ideas?

    Read the article

  • HDD RAID0 question

    - by Jim
    If you have 2 raptor 10k rpm drives in Raid0, can you add another sata (7200prm) drive outside of the RAID or would it have to be inside the RAID? What would be the consequences of adding a 7200 RPM drive to the raptor 10k rpm RAID0 besides the I/O speed going to 7200rpm.

    Read the article

  • How restore DriveImage XML image if cannot make BartPE CD

    - by CChriss
    I have a Windows Vista laptop that won't boot at all. On the D: drive I have DriveImage XML images of C: drive, but I don't have a BartPE boot CD and I don't have a Vista install CD. How can I image the C: using the images on D: if I can't make a BartPE CD because I can't boot to Windows? Is there a BartPE (with DriveImage XML plugin) iso I can download from somewhere, or what can I do? Thanks.

    Read the article

  • How to copy files from HDD to HDD with integrity checking

    - by RafaelM
    I am moving data from an almost dead HDD to an external USB drive using linux , because for some reason Windows cannot see the data. I want to copy a large amount of data over from the HDD to the USB drive with integrity checking. I thought about copying everything over and then checking with md5summer but this would take a reaally long time because its a lot of data and this is not a very powerful PC. What tool can use to do this on Linux?

    Read the article

< Previous Page | 193 194 195 196 197 198 199 200 201 202 203 204  | Next Page >