Search Results

Search found 78 results on 4 pages for '5505'.

Page 2/4 | < Previous Page | 1 2 3 4  | Next Page >

  • Simple Cisco ASA 5505 config issue

    - by Ben Sebborn
    I have a Cisco ASA setup with two interfaces: inside: 192.168.2.254 / 255.255.255.0 SecLevel:100 outside: 192.168.3.250 / 255.255.255.0 SecLevel: 0 I have a static route setup to allow PCs on the inside network to access the internet via a gateway on the outside interface (3.254): outside 0.0.0.0 0.0.0.0 192.168.3.254 This all works fine. I now need to be able to access a PC on the outside interface (3.253) from a PC on the inside interface on port 35300. I understand I should be able to do this with no problems, as I'm going from a higher security level to a lower one. However I can't get any connection. Do I need to set up a seperate static route? Perhaps the route above is overriding what I need to be able to do (is it routing ALL traffic through the gateway?) Any advice on how to do this would be apprecaited. I am configuring this via ASDM but the config can be seen as below: Result of the command: "show running-config" : Saved : ASA Version 8.2(5) ! hostname ciscoasa domain-name xxx.internal names name 192.168.2.201 dev.xxx.internal description Internal Dev server name 192.168.2.200 Newserver ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 shutdown ! interface Ethernet0/4 shutdown ! interface Ethernet0/5 shutdown ! interface Ethernet0/6 shutdown ! interface Ethernet0/7 shutdown ! interface Vlan1 nameif inside security-level 100 ip address 192.168.2.254 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address 192.168.3.250 255.255.255.0 ! ! time-range Workingtime periodic weekdays 9:00 to 18:00 ! ftp mode passive clock timezone GMT/BST 0 clock summer-time GMT/BDT recurring last Sun Mar 1:00 last Sun Oct 2:00 dns domain-lookup inside dns server-group DefaultDNS name-server Newserver domain-name xxx.internal same-security-traffic permit inter-interface object-group service Mysql tcp port-object eq 3306 object-group protocol TCPUDP protocol-object udp protocol-object tcp access-list inside_access_in extended permit ip any any access-list outside_access_in remark ENABLES OUTSDIE ACCESS TO DEV SERVER! access-list outside_access_in extended permit tcp any interface outside eq www time-range Workingtime inactive access-list outside_access_in extended permit tcp host www-1.xxx.com interface outside eq ssh access-list inside_access_in_1 extended permit tcp any any eq www access-list inside_access_in_1 extended permit tcp any any eq https access-list inside_access_in_1 remark Connect to SSH services access-list inside_access_in_1 extended permit tcp any any eq ssh access-list inside_access_in_1 remark Connect to mysql server access-list inside_access_in_1 extended permit tcp any host mysql.xxx.com object-group Mysql access-list inside_access_in_1 extended permit tcp any host mysql.xxx.com eq 3312 access-list inside_access_in_1 extended permit object-group TCPUDP host Newserver any eq domain access-list inside_access_in_1 extended permit icmp any any access-list inside_access_in_1 remark Draytek Admin access-list inside_access_in_1 extended permit tcp any 192.168.3.0 255.255.255.0 eq 4433 access-list inside_access_in_1 remark Phone System access-list inside_access_in_1 extended permit tcp any 192.168.3.0 255.255.255.0 eq 35300 log disable pager lines 24 logging enable logging asdm warnings logging from-address [email protected] logging recipient-address [email protected] level errors mtu inside 1500 mtu outside 1500 ip verify reverse-path interface inside ip verify reverse-path interface outside ipv6 access-list inside_access_ipv6_in permit tcp any any eq www ipv6 access-list inside_access_ipv6_in permit tcp any any eq https ipv6 access-list inside_access_ipv6_in permit tcp any any eq ssh ipv6 access-list inside_access_ipv6_in permit icmp6 any any icmp unreachable rate-limit 1 burst-size 1 icmp permit any outside no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface www dev.xxx.internal www netmask 255.255.255.255 static (inside,outside) tcp interface ssh dev.xxx.internal ssh netmask 255.255.255.255 access-group inside_access_in in interface inside control-plane access-group inside_access_in_1 in interface inside access-group inside_access_ipv6_in in interface inside access-group outside_access_in in interface outside route outside 0.0.0.0 0.0.0.0 192.168.3.254 10 route outside 192.168.3.252 255.255.255.255 192.168.3.252 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy aaa authentication telnet console LOCAL aaa authentication enable console LOCAL

    Read the article

  • ASA 5505 stops local internet when connected to VPN

    - by g18c
    Hi I have a Cisco ASA router running firmware 8.2(5) which hosts an internal LAN on 192.168.30.0/24. I have used the VPN Wizard to setup L2TP access and I can connect in fine from a Windows box and can ping hosts behind the VPN router. However, when connected to the VPN I can no longer ping out to my internet or browse web pages. I would like to be able to access the VPN, and also browse the internet at the same time - I understand this is called split tunneling (have ticked the setting in the wizard but to no effect) and if so how do I do this? Alternatively, if split tunneling is a pain to setup, then making the connected VPN client have internet access from the ASA WAN IP would be OK. Thanks, Chris names ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.30.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address 208.74.158.58 255.255.255.252 ! ftp mode passive access-list inside_nat0_outbound extended permit ip any 10.10.10.0 255.255.255.128 access-list inside_nat0_outbound extended permit ip 192.168.30.0 255.255.255.0 192.168.30.192 255.255.255.192 access-list DefaultRAGroup_splitTunnelAcl standard permit 192.168.30.0 255.255.255.0 access-list DefaultRAGroup_splitTunnelAcl_1 standard permit 192.168.30.0 255.255.255.0 pager lines 24 logging asdm informational mtu inside 1500 mtu outside 1500 ip local pool LANVPNPOOL 192.168.30.220-192.168.30.249 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 192.168.30.0 255.255.255.0 route outside 0.0.0.0 0.0.0.0 208.74.158.57 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy http server enable http 192.168.30.0 255.255.255.0 inside snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac crypto ipsec transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac crypto ipsec transform-set TRANS_ESP_3DES_SHA mode transport crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5 TRANS_ESP_3DES_SHA crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 telnet timeout 5 ssh timeout 5 console timeout 0 dhcpd auto_config outside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept webvpn group-policy DefaultRAGroup internal group-policy DefaultRAGroup attributes dns-server value 192.168.30.3 vpn-tunnel-protocol l2tp-ipsec split-tunnel-policy tunnelspecified split-tunnel-network-list value DefaultRAGroup_splitTunnelAcl_1 username user password Cj7W5X7wERleAewO8ENYtg== nt-encrypted privilege 0 tunnel-group DefaultRAGroup general-attributes address-pool LANVPNPOOL default-group-policy DefaultRAGroup tunnel-group DefaultRAGroup ipsec-attributes pre-shared-key ***** tunnel-group DefaultRAGroup ppp-attributes no authentication chap authentication ms-chap-v2 ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect esmtp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp inspect ip-options ! service-policy global_policy global prompt hostname context : end

    Read the article

  • Cisco ASA 5505 (8.05): asymmetrical group-policy filter on an L2L IPSec tunnel

    - by gravyface
    I'm trying to find a way to setup a bi-directional L2L IPSec tunnel, but with differing group-policy filter ACLs for both sides. I have the following filter ACL setup, applied, and working on my tunnel-group: access-list ACME_FILTER extended permit tcp host 10.0.0.254 host 192.168.0.20 eq 22 access-list ACME_FILTER extended permit icmp host 10.0.0.254 host 192.168.0.20 According to the docs, VPN filters are bi-directional, you always specify the remote host first (10.0.0.254), followed by the local host and (optionally) port number, as per the documentation. However, I do not want the remote host to be able to access my local host's TCP port 22 (SSH) because there's no requirement to do so -- there's only a requirement for my host to access the remote host's SFTP server, not vice-versa. But since these filter ACLs are bidirectional, line 1 is also permitting the remote host to access my host's SSH Server. The documentation I'm reading doesn't seem to clear to me if this is possible; help/clarification much appreciated.

    Read the article

  • Cisco ASA 5505 inside interface multiple ip addresses

    - by Oneiroi
    I have an issue this morning where I want to be able to assign multiple ip addresses to the inside interface to facilitate an ip range migration for an office. Namely from a 192.168.1.x range to the new range, with the minimum of interruption for those working in the office. (New DHCP leases will use the new range, whilst those still on the 192.168.1.x range can continue to work until their lease is renewed). However I can not for the life of me figure out how to achieve this, trying to create multiple interfaces for the job leads to complaints about the license only allowing 2 active interfaces. Any suggestions? thanks in advance.

    Read the article

  • Cisco ASA 5505 network route for static IP hosts

    - by TheCapn
    I've configured my internal VLAN using the most basic settings where ports 1-7 are assigned from a pool of addresses in the range 192.168.15.5 - 192.168.15.36. These hosts are given access to the internet and it works great. What I'm trying to set up now is allowing users who are connected to the device and specify their IP (say I connect and request 192.168.15.45) are given internet access and can still work alongside DHCP hosts. Those with a DHCP assigned address are blocked from the internet. Mostly the issue resides in that I am very new to working with the device. I feel that the solution is easy but I'm not looking in the right spots and don't have the correct terminology down to google it. Do I need to define access control lists? Group policies? a new VLAN? The rules that are set up seem to be specific to the entire /24 subnet but when I request a static IP outside of the DHCP range I get blocked from other hosts and the internet.

    Read the article

  • Text on Cisco ASA console is garbled/missing letters

    - by Some Linux Nerd
    I've actually looked up a number of solutions for this problem and none of them work. There's this Cisco ASA 5505 that I'd like to use, that outputs mildly garbled text with missing characters. I did some googling and found that the most likely problem is a bad baud rate, so I tried all the baud rates, 7N1, 8N2... basically every possibility minicom had. Then I figured (since I can type ok, just not read) that if I factory reset it that it would fix whatever is set wrong with the terminal. That didn't work either. This usb-db9 adapter and console cable work fine on the catalyst switch in our office. My serial settings are 9600 8N1 with no flow control. Anyone know how to fix this? I have an example of the text on pastebin: http://pastebin.com/MAJF0mVU - it's just lots of "Dfaut cnfiuraionfil cotais 1enty." instead of "Default configuration blah blah"

    Read the article

  • VPN is working, except for DNS lookups. Firewall (Cisco ASA 5505) issue?

    - by macke
    I've got the following set up: LAN -> DHCP / DNS / VPN server (OSX 10.6) -> Cisco ASA 5505 -> WAN Connecting to the LAN via VPN works fine. I get all the details properly and I can ping any host on the internal network using their IP. However, I can't do any host lookups whatsoever. I've looked through the logs on and found this nugget in the firewall log: 3 Sep 08 2010 10:46:40 305006 10.0.0.197 65371 portmap translation creation failed for udp src inside:myhostname.local/53 dst inside:10.0.0.197/65371 Port 53 is dns services, no? Because of that log entry, I'm thinking that the issue is with the firewall, not the server. Any ideas? Please keep in mind that I have very little knowledge and experience with this kind of firewall and the little experience I do have is with the ASDM GUI console, not the CLI console.

    Read the article

  • ASA 5505 VPN setup. VPN works but still unable to reach devices in the inside network.

    - by chickenloop
    I've setup a Remote Access VPN on my Cisco ASA 5505. I'm able to connect to my ASA via my phone or the Cisco client, but I'm unable to reach devices in my inside LAN when connected via VPN. The setup is the following: Inside Network : 10.0.0.0/24 VPN_POOL: 172.16.0.0/24 Outside Network: 192.168.1.0/24 ASA is not the perimeter router, there is another device on the 192.168.1.0/24 network which is connected to my cable provider. Obviously UDP port 500 and 4500 are forwarded to the ASA's outside interface. Everything works perfectly, besides the VPN stuff. Config: interface Vlan1 nameif inside security-level 100 ip address 10.0.0.254 255.255.255.0 interface Vlan2 description Outside Interface nameif outside security-level 0 address 192.168.1.254 255.255.255.0 object network VPNPOOL subnet 172.16.0.0 255.255.255.0 object network INSIDE_LAN subnet 10.0.0.0 255.255.255.0 Then the exempt NAT rule. nat (inside,outside) source static INSIDE_LAN INSIDE_LAN destination static VPNPOOL VPNPOOL I don't think that the problem is with the VPN config, as I can successfully establish the VPN connection, but just in case I post it here: group-policy ZSOCA_ASA internal group-policy ZSOCA_ASA attributes vpn-tunnel-protocol ikev1 split-tunnel-policy tunnelspecified split-tunnel-network-list value Split-Tunnel default-domain value default.domain.invalid tunnel-group ZSOCA_ASA type remote-access tunnel-group ZSOCA_ASA general-attributes address-pool VPNPOOL default-group-policy ZSOCA_ASA tunnel-group ZSOCA_ASA ipsec-attributes ikev1 pre-shared-key ***** Any ideas are welcome. Regards.

    Read the article

  • Is this a common/bug on this PPPoE setting for Cisco ASA 5505?

    - by DCAlliances
    We have to change the way the firewall setup due to we've changed the internet provider. The way we setup we have ADSL modem and we have to do a full bridge mode and the firewall configuration has to change from Static IP to Use PPPoE option on Outside interface with PPPoE username and password, CHAP authentication, WAN IP and WAN subnet mask. [See the attachment] It's been working ok with the use of PPPoE option however the issue is that if we un-plug the power cable of the firewall. This "Outside" interface turned to blank - NO WAN IP, PPPoE username and password. So basically, we have to retype this information again. Is this common or a bug? Any ideas? Thanks

    Read the article

  • Is span monitoring on Cisco ASA 5520 possible?

    - by Brent
    From what I have read, you can use the switchport monitor command on ASA 5505's to setup a Span port due to the back of the ASA actually being a switch. On my 5520, I do not see the switchport command listed when issuing a ? via the CLI. How do people monitor traffic on non-5505's? My goal is to connect our IDS/IPS device that is running is promiscuous mode to a Ethernet port on the 5520 to monitor WAN traffic. I do not want to have to pass the WAN traffic through a switch as it would require me to get two (for redundancy) STP/switchport capable switches. Guide to setting up switchport access on a 5505: http://www.wr-mem.com/?p=66

    Read the article

  • problems with ASA 8.4 Nat Rules for a Web Server

    - by Marko
    Having problems with the NAT RULES and Access Rules changes on my ASA5505. Want to straight replace a 5505 with a newer 5505 and unfortunately this means dealing with old version 7.2 and the newer 8.4 configurations. my old NAT RULE: static (inside,outside) WebOutside WebInside netmask 255.255.255.255 and an Access Rule of: access-list outside_access_in extended permit tcp any host WebOutside eq www these dont work in 8.4 I understand there are some changed but I can find little information that makes any sense on how to configure these. Any pointers welcomed.

    Read the article

  • Firewalling a Cisco ASA Split tunnel

    - by dunxd
    I have a Cisco ASA 5510 at head office, and Cisco ASA 5505 in remote offices. The remote offices are connected over a split tunnelled VPN - the ASA 5505s use "Easy VPN" Client type VPN in Network Extension Mode (NEM). I'd like to set firewall rules for the non-tunnelled traffic only. Traffic over the VPN to head office should not have any firewall rules applied. I might want to apply different firewall rules to different remote offices. All the documentation I have been able to find assumes the Client VPN is a software endpoint, and all the configuration is done at the 5510. When using a Cisco 5505 as the VPN client, is it possible to configure any firewalling at the Client end, or does it all have to come from the 5510? Are there any other issues to look out for when split-tunnelling a VPN by this method?

    Read the article

  • sell skimmed dump+pin([email protected])wu transfer,bank transfer,paypal+mailpass

    - by bestseller
    http://megareserve.blogspot.com///////// [email protected]////gmail:[email protected] Sell, Cvv, Bank Logins, Tracks, PayPal, Transfers, WU, Credit Cards, Card, Hacks, Citi, Boa, Visa, MasterCard, Amex, American Express, Make Money Fast, Stolen, Cc, C++, Adder, Western, Union, Banks, Of, America, Wellsfargo, Liberty, Reserve, Gram, Mg, LR, AlertPay ..PAYMENT METHOD LIBERTYRESERVE AND WESTERNUNION ONLY........ Ccv EU is $ 6 per ccv (Visa + Master) Ccv EU is $ 7 per ccv (Amex + Discover) Ccv Au is $ 6 per ccv Ccv Italy is 15 $ per cc sweden 12$ spain 10$ france 12$ Ccv US is $ 1.5 per ccv (Visa) Ccv US is $ 2 per ccv (master) Ccv US is $ 3 per ccv (Amex + Discover) Ccv UK is $ 5 per ccv (Visa + Master) Ccv UK is $ 6 per ccv (Amex + swith) Ccv Ca is $ 6 per ccv (Visa+ Master) Ccv Ca is $ 9 per ccv (Visa Business + Visa Gold) Ccv Germany is 14$ Per Ccv Ccv DOB with US is 15 $ per ccv Ccv DOB with UK is 19 $ per ccv Ccv DOB + BIN with UK 25$ per ccv Ccv US full info is 40 $ per ccv Ccv UK full info is 60 $ per ccv 1 Uk check bins= 12.5$/1cvv 1 Sock live = 1$/1sock live 5day yahoo:[email protected] gmail:[email protected] Balance In Chase:.........70K To 155K ========300$ Balance In Wachovia:.........24K To 80K==========180$ Balance In Boa..........75K To 450K==========400$ Balance In Credit Union:.........Any Amount:=========420$ Balance In Hallifax..........ANY AMOUNT=========420$ Balance In Compass..........ANY AMOUNT=========400$ Balance In Wellsfargo..........ANY AMOUNT=========400$ Balance In Barclays..........80K To 100K=========550$ Balance In Abbey:.........82K ==========650$ Balance in Hsbc:.........50K========650$ and more 1 Paypal with pass email = 50$/paypal 1 Paypal don't have pass email = 20$/Paypal 1 Banklogin us or uk (personel)= 550$ yahoo :[email protected] gmail :[email protected] Track 1/2 Visa Classic, MasterCard Standart US - 13$ UK - 17$ EU - 24$ AU - 26$ Track 1/2 Visa Gold | Platinum | Business | Signature, MasterCard Gold | Platinum US - 17$ UK - 20$ EU - 28$ AU - 30$ Bank transfer Balance 71.000$ CITIBANK SOUTH DAKOTA, N.A. Balance 65.000$ Wachovia: 76.000$ Abbey: 65.000£ Hsbc : 87.000$ Hallifax : 97.000£ Barclays: 110.000£ AHLI UNITED BANK --- 80.000£ LLOYDSTSB ---------- 100.000£ BANK OF SCOTLAND --- 123.000£ BOA ----------210.000$ UBS ---------- 152.000$ RBC BANK ------ 245.000$ BANK OF CANADA -------- 78.000$ BDC ---------- 281.000$ BANK LAURENTIENNE ----- 241.000$ please no test yahoo: [email protected] gmail: [email protected] website ; http://megareserve.blogspot.com Prices For Bin and Its List: 5434, 5419, 4670,374288,545140,454634,3791 with d.o.b,4049,4462,4921.4929.46274547,5506,5569,5404,5031,4921, 5505,5506,4921,4550 ,4552,4988,5186,4462,4543,4567 ,4539,5301,4929,5521 , 4291,5051,4975,5413 5255 4563,4547 4505,4563 5413 5255,5521,5506,4921,4929,54609 7,5609,54609,4543, 4975,5432,5187 ,4973,4627,4049,4779,426565,55 05, 5549, 5404, 5434, 5419, 4670,456730,541361, 451105,4670,5505, 5549, 5404, UK Nomall NO BINS(Serial) with DOB is :10$ UK with BINS(Serial) with DOB is :15$ UK Nomall no BINS(Serial) no DOB is: 6$ UK with BINS(Serial) is :12$ Please do not request : cc for TEST and FREE. DON'T CONTACT ME IF YOU NOT READY NEED TO BUY .

    Read the article

  • Skype performance in IPSEC VPN

    - by dunxd
    I've been challenged to "improve Skype performance" for calls within my organisation. Having read the Skype IT Administrators Guide I am wondering whether we might have a performance issue where the Skype Clients in a call are all on our WAN. The call is initiated by a Skype Client at our head office, and terminated on a Skype Client in a remote office connected via IPSEC VPN. Where this happens, I assume the trafficfrom Client A (encrypted by Skype) goes to our ASA 5510, where it is furtehr encrypted, sent to the remote ASA 5505 decrypted, then passed to Client B which decrypts the Skype encryption. Would the call quality benefit if the traffic didn't go over the VPN, but instead only relied on Skype's encryption? I imagine I could achieve this by setting up a SOCKS5 proxy in our HQ DMZ for Skype traffic. Then the traffic goes from Client A to Proxy, over the Skype relay network, then arrives at Cisco ASA 5505 as any other internet traffic, and then to Client B. Is there likely to be any performance benefit in doing this? If so, is there a way to do it that doesn't require a proxy? Has anyone else tackled this?

    Read the article

  • Public-to-Public IPSec tunnel: NAT confusion

    - by WuckaChucka
    I know this is possible -- and apparently fairly common with larger companies that don't/can't route private addresses for overlap reasons -- but I can't wrap my head around how to get this to work. I'm playing around with pfSense, Vyatta and a Cisco 5505 right now, hardware-wise. So here's my setup: WEST: Vyatta outside: 10.0.0.254/24 inside: 172.16.0.1/24 machine a: 172.16.0.200/24 EAST: Cisco 5505 outside: 10.0.0.210/24 inside: 192.168.10.1 machine b (webserver): 192.168.10.2 So what we're trying to do is this: route traffic across the tunnel from machine A to machine B without using private addresses. i.e. 172.16.0.200 makes a TCP request to 10.0.0.210:80, and as far as EAST is concerned, it sees a src IP of 10.0.0.254. On WEST, I have your typical many-to-one Source NAT to translate 172.16.0.0/24 to 10.0.0.254 and that's confirmed to be working. Also on WEST, I have the following IPSec config: Local IP: 10.0.0.254 Peer IP: 10.0.0.210 local subnet: 10.0.0.254/32 remote subnet: 10.0.0.210/32 I have the reversed configuration on EAST. What happens when I make a request from machine A to 10.0.0.210:80 is that the SNAT translates the private address of machine A to 10.0.0.254 and it's routed out (and discarded at the other end) without establishing the tunnel. What I'm assuming is happening is that the inside interface on WEST receives a packet from 172.16.0.200 and since this doesn't match the local subnet defined in the tunnel configuration, it's not processed by the IPSec engine and the tunnel is not established. How do you make this work? Seems like a chicken and egg thing with the NAT and IPSec and I just can't wrap my head around how this can be done: can I say, "if a packet is received on the inside interface with a destination of 10.0.0.210, translate it to 10.0.0.254 before the IPSec engine inspects it"?

    Read the article

  • Simplest DNS solution for remote offices

    - by dunxd
    I look after a bunch of remote offices that connect via VPN - a Cisco ASA 5505 in each office acts as Firewall and VPN end point. Beyond that we keep things as simple as possible in the offices to minimise the support burden. We don't have any kind of server except in offices large enough to justify having someone dedicated to IT. Basically there is the ASA, some computers, a network printer and a switch. One of the problems I am seeing in a lot of offices is that DNS requests looking up hosts inside our network often fail - I'm assuming timeouts due to the offices internet connection (they are all in developing world countries) having some sub-optimal qualities (e.g. high latency caused by VSAT segments, or packet loss. The obvious solution to this is to have some sort of local DNS service that can serve local requests - so I think it would need to do zone transfers from our Microsoft Windows 2008 R2 DNS servers at HQ. However, simply installing Windows Servers in each office is both expensive, and creates a support burden. This got me thinking about pfsense/m0n0wall on embedded devices - those can act as a DNS server, and could be configured at HQ and sent out as just something that needs to be plugged into the network and can then be forgotten about by the staff locally. Maybe there are some alternatives to the ASA 5505 that include some DNS functionality. Has anyone here dealt with the problem, either using some kind of embedded device, or found some other solution? Any gotchas or reasons to avoid what I have suggested?

    Read the article

  • Web Content Filtering

    - by Byron Wilcox
    I have recently bought a Cisco ASA 5505 for my small business, I was initially led to believe this device could do some limited website filtering that we would need. (one list of unrestricted, and a second for email only) Since it has come to my attention that it may not be able to do this what equipment or software will I need to make this happen?

    Read the article

  • Cisco ASA log error "regular translation creation failed for icmp ..."

    - by Martijn Heemels
    Every few seconds our new Cisco ASA 5505 firewall is logging errors that I can't figure out with my limited Cisco experience. Severity Date Time Syslog ID Source IP Destination IP Description 3 Mar 25 2010 17:21:14 305006 8.8.8.8 regular translation creation failed for icmp src inside:10.10.0.200 dst outside:8.8.8.8 (type 3, code 3) 3 Mar 25 2010 17:18:37 305006 8.8.4.4 regular translation creation failed for icmp src inside:10.10.0.200 dst outside:8.8.4.4 (type 3, code 3) The logged inside IP is our internal DNS resolver, and the outside IP's are Google's public DNS servers. ICMP Type 3 Code 3 means "Port Unreachable" Our "outside" interface has a fixed IP and our "inside" interface is in the 10.10.0.0/16 subnet. The 'Inspect DNS' Service Policy is enabled, with the preset DNS inspection map. Furthermore there's an ACL that allows all inbound ICMP on the "outside" interface. I've spent hours trying to figure this one out, so any and all advice is welcome!

    Read the article

  • Managed hosting firewall vs managing own firewall

    - by ddawber
    I posted on stackoverflow as to the overall benefits of managed hosting vs non-managed hosting. The more I think about it, it seems to boil down to one question: should I use a managed host because they take care of the firewall, or would I be okay managing my own, software firewall? The sites on the box do get quite a lot of traffic but as for throughput and what-not, it's not something I know much about. Ideally, i'd take my sites over to a Linode stack and manage incoming connections using iptables or an alternative. Here are some example hardware solutions a managed host would provide: Cisco Pix 501, Pix 506, Pix 515 and ASA 5505 and ASA 5510 Firewalls, configurable in a control panel the likes of an enterprise firewall such as FortiGate 110C Aside from this, I do not need managed hosting, so I appreciate your suggestions.

    Read the article

  • Can't figure out error in Cisco ASA log "regular translation creation failed for icmp ..."

    - by Martijn Heemels
    Every few seconds our new Cisco ASA 5505 firewall is logging errors that I can't figure out with my limited Cisco experience. Severity Date Time Syslog ID Source IP Destination IP Description 3 Mar 25 2010 17:21:14 305006 8.8.8.8 regular translation creation failed for icmp src inside:10.10.0.200 dst outside:8.8.8.8 (type 3, code 3) 3 Mar 25 2010 17:18:37 305006 8.8.4.4 regular translation creation failed for icmp src inside:10.10.0.200 dst outside:8.8.4.4 (type 3, code 3) The logged inside IP is our internal DNS resolver, and the outside IP's are Google's public DNS servers. ICMP Type 3 Code 3 means "Port Unreachable" Our "outside" interface has a fixed IP and our "inside" interface is in the 10.10.0.0/16 subnet. The 'Inspect DNS' Service Policy is enabled, with the preset DNS inspection map. Furthermore there's an ACL that allows all inbound ICMP on the "outside" interface. I've spent hours trying to figure this one out, so any and all advice is welcome!

    Read the article

  • Cisco ASA Hairpinning with Dynamic IP

    - by Joseph Sturtevant
    I currently have my Cisco ASA 5505 firewall configured to forward port 80 from the outside interface to a host on my dmz interface. I also need to allow clients on my inside interface to access the host in the dmz by entering the public ip / dns record in their browsers. I was able to do that by following the instructions here, resulting in the following configuration: static (dmz,outside) tcp interface www 192.168.1.5 www netmask 255.255.255.255 static (dmz,inside) tcp 74.125.45.100 www 192.168.1.5 www netmask 255.255.255.255 (Where 74.125.45.100 is my public IP and 192.168.1.5 is the IP of the dmz host) This works great except for the fact that my network has a dynamic public IP and this configuration will therefore break as soon as my public IP changes. Is there a way to do what I want with a dynamic ip? Note: Adding an internal DNS record won't solve my problem since I have multiple dmz hosts mapped to different ports on the public IP.

    Read the article

  • UDP flooding multiple servers

    - by Chris Gurney
    What do you suggest? Being UDP flooded as I write to multiple servers in different data centers in 5 different countries . Up to 250,000 packets a second. I believe Cisco routers 5505 would not handle that - (some of our datacenter hosters can offer them. Some have no firewalls to offer.) Our clients naturally have constant disconnects to the server they are on. Hacker started this about three weeks ago. Sometimes for a few hours - up to a few days. If we can't stop it hitting the server with firewalls then how do we stop the hacker - now there is the challenge! Update : Found some of the data centers offer up to 10 firewall rules but would their routers be able to handle the possible volume I am talking about? Thanks Chris

    Read the article

  • Monitoring ASA packet loss via SNMP

    - by dunxd
    I want to monitor packet loss on my ASA 5505 VPN endpoints using SNMP. This is so I can graph the rates in Cacti and/or get alerts in Nagios. However, I am not sure what SNMP values I should use to measure packet loss. In the ASA I can run sh interface Internet stats to show traffic statistics for the interface connected to the Internet. This shows 1 minute and 5 minute drop rates. Are these measures an indicator of packet loss? Are there SNMP values I can access that correspond to those values? Should I be looking at different values? Is the ASA even able to measure packet loss?

    Read the article

  • Cisco training basic, entry, ASA/PIX. Help to understand network

    - by Inbr3d
    I need to learn how to configure Cisco ASA/PIX boxes within my network. I have the task to impliment a new ASA 5505 into a new site we purchased. I have over 9 devices linking my sites together and with no support from the previous IT company im finding it hard to get to terms with what they can do and what they are currently doing. I know there are hundreds of guides how to configure them but into an existing environment? can anyone recommend courses within the UK that can help me? Im not much of a book reader, i would need to be able to manage my network after. also, should i seek external contracts to support these devices? as they are critical for our work. thanks

    Read the article

< Previous Page | 1 2 3 4  | Next Page >