Search Results

Search found 55 results on 3 pages for 'bonding'.

Page 2/3 | < Previous Page | 1 2 3  | Next Page >

• lacp, cicso 3550, 3560, help with configuration

  - by Flamewires

  Hey all this is a repost from a question I asked on the cisco forums but never got a useful reply. Hey I'm trying to convert the FreeBSD servers at work to dual-gig lagg links from regular gigabit links. Our production servers are on a 3560. I have a small test environment on a 3550. I have achieved fail-over, but am having troubles achieving the speed increase. All servers are running gig intel (em) cards. The configs for the servers are: BSDServer: #!/bin/sh #bring up both interfaces ifconfig em0 up media 1000baseTX mediaopt full-duplex ifconfig em1 up media 1000baseTX mediaopt full-duplex #create the lagg interface ifconfig lagg0 create #set lagg0's protocol to lacp, add both cards to the interface, #and assign it em1's ip/netmask ifconfig lagg0 laggproto lacp laggport em0 laggport em1 ***.***.***.*** netmask 255.255.255.0 The switches are configured as follows: #clear out old junk no int Po1 default int range GigabitEthernet 0/15 - 16 # config ports interface range GigabitEthernet 0/15 - 16 description lagg-test switchport duplex full speed 1000 switchport access vlan 192 spanning-tree portfast channel-group 1 mode active channel-protocol lacp **** switchport trunk encapsulation dot1q **** no shutdown exit interface Port-channel 1 description lagginterface switchport access vlan 192 exit port-channel load-balance src-mac end obviously change 1000's to 100's and GigabitEthernet to FastEthernet for the 3550's config, as that switch has 100Mbit speed ports. With this config on the 3550, I get failover and 92Mbits/sec speed on both links, simultaneously, connecting to 2 hosts.(tested with iperf) Success. However this is only with the "switchport trunk encapsulation dot1q" line. First, I do not understand why I need this, I thought it was only for connecting switches. Is there some other setting which this turns on that is actually responsible for the speed increase? Second, This config does not work on the 3560. I get failover, but not the speed increase. Speeds drop from gig/sec to 500Mbit/sec when I make 2 simultaneous connections to the server with or without the encapsulation line. I should mention that both switches are using source-mac load balancing. In my test I am using Iperf. I have the server(lagg box) setup as the server(iperf -s), and the client computers are client(iperf -c server-ip-address), so the source mac(and IP) are different for both connections. Any ideas/corrections/questions would be helpful, as the gig switches are what I actually need the lagg links on. Ask if you need more information.

  Read the article

• Monitor Bonded Interface for Disconnection

  - by bradlis7

  I am trying to monitor for network failures on a machine, and one portion of that is to monitor interfaces that are intended to be active also be "RUNNING". An Ethernet port, such as eth0, will say "RUNNING" if it is physically connected to another device. The problem lies in the bonded interfaces, such as bond0. If all of the ethernet devices are disconnected, it still says that it is running, and it is still pingable. Is this by design, or is my system setup incorrectly? Does the miimon option have something to do with this?

  Read the article

• Load balancing with Cisco router

  - by you8301083

  I have a Cisco router with two bonded T1's which are setup as a VPN to the main office. We need more bandwidth but can't get other connections (or it's too costly), so I would like to have a dsl connection installed. This DSL connection will run over a VPN to the same main office, but it won't be bonded with the T1's - so it won't act as a single connection. Since the three circuits won't act as a single connection (basically would be two connections 2 T1's + 1 DSL) we would have to split the network in half - but I don't want to do that. Instead, would it be possible to send all HTTP/HTTPS over the DSL connection but send all mission critical data (such as voice/active directory) over the T1's? I basically want to send specific ports over DSL and everything else over the T1's without separating half of the users traffic over the DSL and the rest over the T1's.

  Read the article

• Creating ip alias on bonded interface ie. bond0:1

  - by bobothechimp

  System: HP Proliant DL360 G5 running CentOS 5.4 Bonded interface is working fine for a long time. I just went to add an alias the way I always have on a regular interface, and on first check it works (pinging on the local box) but it is not accessable from outside (iptables is turned off). In addition with this setup the normal network response started to decline, hanging for around a minute before I could get a prompt on login. Here are my config files: [root network-scripts]# cat ifcfg-eth0 DEVICE=eth0 BOOTPROTO=none ONBOOT=yes MASTER=bond0 SLAVE=yes USERCTL=no [root network-scripts]# cat ifcfg-eth1 DEVICE=eth1 BOOTPROTO=none ONBOOT=yes MASTER=bond0 SLAVE=yes USERCTL=no [root network-scripts]# cat ifcfg-bond0 DEVICE=bond0 BONDING_OPTS="mode=1 miimon=100" BOOTPROTO=none ONBOOT=yes NETWORK=10.2.1.0 NETMASK=255.255.255.0 IPADDR=10.2.1.11 USERCTL=no [root network-scripts]# cat ifcfg-bond0:1 DEVICE=bond0:1 BOOTPROTO=static ONBOOT=yes NETWORK=10.2.1.0 NETMASK=255.255.255.0 IPADDR=10.2.1.12 USERCTL=no any thoughts?

  Read the article

• My Graduate Experience at Oracle by Mayuri Khinvasara

  - by david.talamelli

  My experience at Oracle. I still vividly remember the day, when my name was announced in the campus hiring list of Oracle at my college. I was proud of myself but at the same time, I was getting goose bumps!!! A new world had arrived before me and the anxiousness of whether I could survive it or not had gripped me. Nervous about moving into an unknown city, I came to visit Hyderabad with my father. One look at the Oracle Campus and I felt some kind of magnetism pulling me towards it. And then, I joined Oracle in June 2009, with a lot of apprehensions in my mind. The HR Rep made us really comfortable in the first week itself. I met so many new people, managers, HR folks and most importantly 20 other Campus Hires like me. Then we had our team bonding sessions, team parties etc. I didn’t realize when the transition from campus to corporate happened. And I had started loving it. The confidence the HR Reps gave us and the bonding our managers imbibed in us, made us all ready for the new life ahead. Then started the rigorous training sessions, the excitement about our new work, new cubicles, new desktops, our first business cards, our first conference call and so on. I made new friends which were now my extended family, the freedom and courage of living alone. I was enjoying all that. As I was getting totally immersed into my regular work schedule I started getting to know the innumerable Oracle products, their functionalities, implementations and realizing the brand that Oracle is. Work pressure started increasing and so did the challenges to understand and deliver. I Didn’t realize how days and soon months passed by. Then came a golden chance to visit the Oracle Headquarters in US for 45 days training in November 2009. Once again, the excitement was enormous about the counter team-mates in HQ, the trainings ahead, the US work culture and my stay there. I felt so privileged for the company I was working. Boarding an international flight for the first time and visiting famous US cities which I had just seen in movies, was now a reality. It was a totally amazing experience. Work pressure kept me really busy, with learning new things every day, the immense satisfaction of delivering something, the nightmares of debugging a mistake, only to realize how silly it was.  I was enjoying the process. Soon a year passed by. I had transformed into this corporate software professional, I couldn’t believe I could be. Today, I complete 1 year and 8 months at Oracle and continue to look forward to the enriching experience I will have here. Truly one of the Top Companies in the World. Mayuri Khinvasara

  Read the article

• bond0:0 + define virtual IP

  - by yael

  hi all in my linux server I have the follwoing: Linux Version - RedHat-Linux- 5.3.0.0 (this linux server only only one LAN) more /etc/sysconfig/network-scripts/ifcfg-bond0:0 DEVICE=bond0:0 ONBOOT=yes BOOTPROTO=static IPADDR=10.10.10.12 NETMASK=255.255.255.0 ifconfig -a bond0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) bond0:0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 inet addr:10.10.10.12 Bcast:1.1.1.255 Mask:255.255.255.0 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 eth0 Link encap:Ethernet HWaddr 00:0E:0C:C7:F8:92 inet addr:1.1.1.1 Bcast:1.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::20e:cff:fec7:f892/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:8600 errors:0 dropped:0 overruns:0 frame:0 TX packets:4764 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:717979 (701.1 KiB) TX bytes:598620 (584.5 KiB) Memory:b8820000-b8840000 my problems: why I get HWaddr 00:00:00:00:00:00 and not the real MAC address I cant ping to other server with 10.10.10.11 from my server is it posible to define bond0:0 when I have only one LAN (eth0) other info: more /etc/modprobe.conf alias eth0 e1000e alias eth1 e1000e alias eth2 e1000e alias eth3 e1000e alias scsi_hostadapter mptbase alias scsi_hostadapter1 mptsas alias scsi_hostadapter2 ata_piix alias bond0 bonding alias bond1 bonding

  Read the article

• bond0:0 + define virtual IP

  - by yael

  hi all in my linux server I have the follwoing: Linux Version - RedHat-Linux- 5.3.0.0 (this linux server only only one LAN) more /etc/sysconfig/network-scripts/ifcfg-bond0:0 DEVICE=bond0:0 ONBOOT=yes BOOTPROTO=static IPADDR=10.10.10.12 NETMASK=255.255.255.0 ifconfig -a bond0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) bond0:0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 inet addr:10.10.10.12 Bcast:1.1.1.255 Mask:255.255.255.0 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 eth0 Link encap:Ethernet HWaddr 00:0E:0C:C7:F8:92 inet addr:1.1.1.1 Bcast:1.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::20e:cff:fec7:f892/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:8600 errors:0 dropped:0 overruns:0 frame:0 TX packets:4764 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:717979 (701.1 KiB) TX bytes:598620 (584.5 KiB) Memory:b8820000-b8840000 my problems: why I get HWaddr 00:00:00:00:00:00 and not the real MAC address I cant ping to other server with 10.10.10.11 from my server is it posible to define bond0:0 when I have only one LAN (eth0) other info: more /etc/modprobe.conf alias eth0 e1000e alias eth1 e1000e alias eth2 e1000e alias eth3 e1000e alias scsi_hostadapter mptbase alias scsi_hostadapter1 mptsas alias scsi_hostadapter2 ata_piix alias bond0 bonding alias bond1 bonding

  Read the article

• bond0:0 + define virtual IP

  - by yael

  in my Linux server I have the following: Linux Version - RedHat-Linux- 5.3.0.0 (this Linux server only only one LAN) more /etc/sysconfig/network-scripts/ifcfg-bond0:0 DEVICE=bond0:0 ONBOOT=yes BOOTPROTO=static IPADDR=10.10.10.12 NETMASK=255.255.255.0 ifconfig -a bond0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) bond0:0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 inet addr:10.10.10.12 Bcast:1.1.1.255 Mask:255.255.255.0 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 eth0 Link encap:Ethernet HWaddr 00:0E:0C:C7:F8:92 inet addr:1.1.1.1 Bcast:1.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::20e:cff:fec7:f892/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:8600 errors:0 dropped:0 overruns:0 frame:0 TX packets:4764 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:717979 (701.1 KiB) TX bytes:598620 (584.5 KiB) Memory:b8820000-b8840000 my problems: why I get HWaddr 00:00:00:00:00:00 and not the real MAC address I cant ping to other server with 10.10.10.11 from my server is it possible to define bond0:0 when I have only one LAN (eth0) other info: more /etc/modprobe.conf alias eth0 e1000e alias eth1 e1000e alias eth2 e1000e alias eth3 e1000e alias scsi_hostadapter mptbase alias scsi_hostadapter1 mptsas alias scsi_hostadapter2 ata_piix alias bond0 bonding alias bond1 bonding

  Read the article

• Load-balancing between a Procurve switch and a server

  - by vlad

  Hello I've been searching around the web for this problem i've been having. It's similar in a way to this question: How exactly & specifically does layer 3 LACP destination address hashing work? My setup is as follows: I have a central switch, a Procurve 2510G-24, image version Y.11.16. It's the center of a star topology, there are four switches connected to it via a single gigabit link. Those switches service the users. On the central switch, I have a server with two gigabit interfaces that I want to bond together in order to achieve higher throughput, and two other servers that have single gigabit connections to the switch. The topology looks as follows: sw1 sw2 sw3 sw4 | | | | --------------------- | sw0 | --------------------- || | | srv1 srv2 srv3 The servers were running FreeBSD 8.1. On srv1 I set up a lagg interface using the lacp protocol, and on the switch I set up a trunk for the two ports using lacp as well. The switch showed that the server was a lacp partner, I could ping the server from another computer, and the server could ping other computers. If I unplugged one of the cables, the connection would keep working, so everything looked fine. Until I tested throughput. There was only one link used between srv1 and sw0. All testing was conducted with iperf, and load distribution was checked with systat -ifstat. I was looking to test the load balancing for both receive and send operations, as I want this server to be a file server. There were therefore two scenarios: iperf -s on srv1 and iperf -c on the other servers iperf -s on the other servers and iperf -c on srv1 connected to all the other servers. Every time only one link was used. If one cable was unplugged, the connections would keep going. However, once the cable was plugged back in, the load was not distributed. Each and every server is able to fill the gigabit link. In one-to-one test scenarios, iperf was reporting around 940Mbps. The CPU usage was around 20%, which means that the servers could withstand a doubling of the throughput. srv1 is a dell poweredge sc1425 with onboard intel 82541GI nics (em driver on freebsd). After troubleshooting a previous problem with vlan tagging on top of a lagg interface, it turned out that the em could not support this. So I figured that maybe something else is wrong with the em drivers and / or lagg stack, so I started up backtrack 4r2 on this same server. So srv1 now uses linux kernel 2.6.35.8. I set up a bonding interface bond0. The kernel module was loaded with option mode=4 in order to get lacp. The switch was happy with the link, I could ping to and from the server. I could even put vlans on top of the bonding interface. However, only half the problem was solved: if I used srv1 as a client to the other servers, iperf was reporting around 940Mbps for each connection, and bwm-ng showed, of course, a nice distribution of the load between the two nics; if I run the iperf server on srv1 and tried to connect with the other servers, there was no load balancing. I thought that maybe I was out of luck and the hashes for the two mac addresses of the clients were the same, so I brought in two new servers and tested with the four of them at the same time, and still nothing changed. I tried disabling and reenabling one of the links, and all that happened was the traffic switched from one link to the other and back to the first again. I also tried setting the trunk to "plain trunk mode" on the switch, and experimented with other bonding modes (roundrobin, xor, alb, tlb) but I never saw any traffic distribution. One interesting thing, though: one of the four switches is a Cisco 2950, image version 12.1(22)EA7. It has 48 10/100 ports and 2 gigabit uplinks. I have a server (call it srv4) with a 4 channel trunk connected to it (4x100), FreeBSD 8.0 release. The switch is connected to sw0 via gigabit. If I set up an iperf server on one of the servers connected to sw0 and a client on srv4, ALL 4 links are used, and iperf reports around 330Mbps. systat -ifstat shows all four interfaces are used. The cisco port-channel uses src-mac to balance the load. The HP should use both the source and destination according to the manual, so it should work as well. Could this mean there is some bug in the HP firmware? Am I doing something wrong?

  Read the article

• Setup link aggregation and jumbo frames on VMware ESXi 4

  - by Sysadminicus

  I'm setting up an ESXi 4 server to connect to an NFS datastore. I'd like to bond two of the NICs together and use jumbo frames for the NFS connection on a private (non-management) network. I setup a new switch with the 2 NICs and am able to connect to the NFS share over it, but could use some guidance on getting jumbo frames and link aggregation/bonding/teaming working.

  Read the article

• Determine hostname of connected ethernet switch

  - by Beastcraft

  I've a bonding on two interfaces. I'd like to monitor wether they are connected to different switches (the switches have hostnames). ethX should be connected to switchX and ethY to switchY. Currently I'm checking this with following command: tcpdump -vv -s0 -i ethX ether host 01:00:0c:cc:cc:cc After a minute it prints out the hostname (and much more information) from the switch. Are there any other solutions to monitor this? Greeting

  Read the article

• KVM-Guests can't get past bridge - no internet connection

  - by tmn29a

  I'm running a backported KVM on a Debian Squeeze. ATM the KVM-Guest can't connect to the internet through the bridge I have set up. The guests can reach each other, the host but nothing outside. I can neither ping, nslookup or do anything to a remote address. The guest are configured to have a static IP. When I didn;t have the bridge but a virtual bridge (the KVM-default) the guest could connect fine. After setting up the bridge things broke, so I think the problem lies there. # The loopback network interface auto lo br0 iface lo inet loopback # Bonding Interface auto bond0 iface bond0 inet static address 10.XXX.XXX.84 netmask 255.255.255.192 network 10.XXX.XXX.64 gateway 10.XXX.XXX.65 slaves eth0 eth1 bond_mode active-backup bond_miimon 100 bond_downdelay 200 bond_updelay 200 iface br0 inet static bridge_ports eth0 eth1 address 172.xxx.xxx.65 broadcast 172.xxx.xxx.127 netmask 255.255.255.192 gateway 172.xxx.xxx.65 bridge_stp on bridge_maxwait 0 Thanks in advance for your help !

  Read the article

• What You Said: Your Favorite Co-Op Games

  - by Jason Fitzpatrick

  While competitive gaming is fun, reader response to this week’s Ask the Readers question shows that good old beat-the-bad-guys-together cooperative gaming is as popular as ever. Read on to see what your fellow readers are playing. By far the most popular nomination for favorite co-op game was an outright classic: 1987′s smash hit Contra. Originally released as an arcade game, it was ported to the Nintendo Entertainment System in 1988. Contra was groundbreaking for the time as it featured simultaneous play for the two players–you and a friend could play side by side without waiting to take your turn. Clearly that kind of side-by-side play resonated with readers. RJ writes: When my fiance and I played and beat Contra on the NES. I knew she was the one and we got married and its been great. That’s no small feat; Contra was voted “Toughest Game to Beat” by IGN.com readers. Even readers who had moved on to newer games still recall Contra fondly; Jami writes: The Gears of War trilogy on 360 is my favorite co-op currently, although I do have fond memories of bonding with my brother playing some co-op Contra on the NES. HTG Explains: What is the Windows Page File and Should You Disable It? How To Get a Better Wireless Signal and Reduce Wireless Network Interference How To Troubleshoot Internet Connection Problems

  Read the article

• 11gR2???---gipc????

  - by Allen Gao

  Normal 0 7.8 ? 0 2 false false false EN-US ZH-CN X-NONE DefSemiHidden="true" DefQFormat="false" DefPriority="99" LatentStyleCount="267" UnhideWhenUsed="false" QFormat="true" Name="Normal"/ UnhideWhenUsed="false" QFormat="true" Name="heading 1"/ UnhideWhenUsed="false" QFormat="true" Name="Title"/ UnhideWhenUsed="false" QFormat="true" Name="Subtitle"/ UnhideWhenUsed="false" QFormat="true" Name="Strong"/ UnhideWhenUsed="false" QFormat="true" Name="Emphasis"/ UnhideWhenUsed="false" Name="Table Grid"/ UnhideWhenUsed="false" QFormat="true" Name="No Spacing"/ UnhideWhenUsed="false" Name="Light Shading"/ UnhideWhenUsed="false" Name="Light List"/ UnhideWhenUsed="false" Name="Light Grid"/ UnhideWhenUsed="false" Name="Medium Shading 1"/ UnhideWhenUsed="false" Name="Medium Shading 2"/ UnhideWhenUsed="false" Name="Medium List 1"/ UnhideWhenUsed="false" Name="Medium List 2"/ UnhideWhenUsed="false" Name="Medium Grid 1"/ UnhideWhenUsed="false" Name="Medium Grid 2"/ UnhideWhenUsed="false" Name="Medium Grid 3"/ UnhideWhenUsed="false" Name="Dark List"/ UnhideWhenUsed="false" Name="Colorful Shading"/ UnhideWhenUsed="false" Name="Colorful List"/ UnhideWhenUsed="false" Name="Colorful Grid"/ UnhideWhenUsed="false" Name="Light Shading Accent 1"/ UnhideWhenUsed="false" Name="Light List Accent 1"/ UnhideWhenUsed="false" Name="Light Grid Accent 1"/ UnhideWhenUsed="false" Name="Medium Shading 1 Accent 1"/ UnhideWhenUsed="false" Name="Medium Shading 2 Accent 1"/ UnhideWhenUsed="false" Name="Medium List 1 Accent 1"/ UnhideWhenUsed="false" QFormat="true" Name="List Paragraph"/ UnhideWhenUsed="false" QFormat="true" Name="Quote"/ UnhideWhenUsed="false" QFormat="true" Name="Intense Quote"/ UnhideWhenUsed="false" Name="Medium List 2 Accent 1"/ UnhideWhenUsed="false" Name="Medium Grid 1 Accent 1"/ UnhideWhenUsed="false" Name="Medium Grid 2 Accent 1"/ UnhideWhenUsed="false" Name="Medium Grid 3 Accent 1"/ UnhideWhenUsed="false" Name="Dark List Accent 1"/ UnhideWhenUsed="false" Name="Colorful Shading Accent 1"/ UnhideWhenUsed="false" Name="Colorful List Accent 1"/ UnhideWhenUsed="false" Name="Colorful Grid Accent 1"/ UnhideWhenUsed="false" Name="Light Shading Accent 2"/ UnhideWhenUsed="false" Name="Light List Accent 2"/ UnhideWhenUsed="false" Name="Light Grid Accent 2"/ UnhideWhenUsed="false" Name="Medium Shading 1 Accent 2"/ UnhideWhenUsed="false" Name="Medium Shading 2 Accent 2"/ UnhideWhenUsed="false" Name="Medium List 1 Accent 2"/ UnhideWhenUsed="false" Name="Medium List 2 Accent 2"/ UnhideWhenUsed="false" Name="Medium Grid 1 Accent 2"/ UnhideWhenUsed="false" Name="Medium Grid 2 Accent 2"/ UnhideWhenUsed="false" Name="Medium Grid 3 Accent 2"/ UnhideWhenUsed="false" Name="Dark List Accent 2"/ UnhideWhenUsed="false" Name="Colorful Shading Accent 2"/ UnhideWhenUsed="false" Name="Colorful List Accent 2"/ UnhideWhenUsed="false" Name="Colorful Grid Accent 2"/ UnhideWhenUsed="false" Name="Light Shading Accent 3"/ UnhideWhenUsed="false" Name="Light List Accent 3"/ UnhideWhenUsed="false" Name="Light Grid Accent 3"/ UnhideWhenUsed="false" Name="Medium Shading 1 Accent 3"/ UnhideWhenUsed="false" Name="Medium Shading 2 Accent 3"/ UnhideWhenUsed="false" Name="Medium List 1 Accent 3"/ UnhideWhenUsed="false" Name="Medium List 2 Accent 3"/ UnhideWhenUsed="false" Name="Medium Grid 1 Accent 3"/ UnhideWhenUsed="false" Name="Medium Grid 2 Accent 3"/ UnhideWhenUsed="false" Name="Medium Grid 3 Accent 3"/ UnhideWhenUsed="false" Name="Dark List Accent 3"/ UnhideWhenUsed="false" Name="Colorful Shading Accent 3"/ UnhideWhenUsed="false" Name="Colorful List Accent 3"/ UnhideWhenUsed="false" Name="Colorful Grid Accent 3"/ UnhideWhenUsed="false" Name="Light Shading Accent 4"/ UnhideWhenUsed="false" Name="Light List Accent 4"/ UnhideWhenUsed="false" Name="Light Grid Accent 4"/ UnhideWhenUsed="false" Name="Medium Shading 1 Accent 4"/ UnhideWhenUsed="false" Name="Medium Shading 2 Accent 4"/ UnhideWhenUsed="false" Name="Medium List 1 Accent 4"/ UnhideWhenUsed="false" Name="Medium List 2 Accent 4"/ UnhideWhenUsed="false" Name="Medium Grid 1 Accent 4"/ UnhideWhenUsed="false" Name="Medium Grid 2 Accent 4"/ UnhideWhenUsed="false" Name="Medium Grid 3 Accent 4"/ UnhideWhenUsed="false" Name="Dark List Accent 4"/ UnhideWhenUsed="false" Name="Colorful Shading Accent 4"/ UnhideWhenUsed="false" Name="Colorful List Accent 4"/ UnhideWhenUsed="false" Name="Colorful Grid Accent 4"/ UnhideWhenUsed="false" Name="Light Shading Accent 5"/ UnhideWhenUsed="false" Name="Light List Accent 5"/ UnhideWhenUsed="false" Name="Light Grid Accent 5"/ UnhideWhenUsed="false" Name="Medium Shading 1 Accent 5"/ UnhideWhenUsed="false" Name="Medium Shading 2 Accent 5"/ UnhideWhenUsed="false" Name="Medium List 1 Accent 5"/ UnhideWhenUsed="false" Name="Medium List 2 Accent 5"/ UnhideWhenUsed="false" Name="Medium Grid 1 Accent 5"/ UnhideWhenUsed="false" Name="Medium Grid 2 Accent 5"/ UnhideWhenUsed="false" Name="Medium Grid 3 Accent 5"/ UnhideWhenUsed="false" Name="Dark List Accent 5"/ UnhideWhenUsed="false" Name="Colorful Shading Accent 5"/ UnhideWhenUsed="false" Name="Colorful List Accent 5"/ UnhideWhenUsed="false" Name="Colorful Grid Accent 5"/ UnhideWhenUsed="false" Name="Light Shading Accent 6"/ UnhideWhenUsed="false" Name="Light List Accent 6"/ UnhideWhenUsed="false" Name="Light Grid Accent 6"/ UnhideWhenUsed="false" Name="Medium Shading 1 Accent 6"/ UnhideWhenUsed="false" Name="Medium Shading 2 Accent 6"/ UnhideWhenUsed="false" Name="Medium List 1 Accent 6"/ UnhideWhenUsed="false" Name="Medium List 2 Accent 6"/ UnhideWhenUsed="false" Name="Medium Grid 1 Accent 6"/ UnhideWhenUsed="false" Name="Medium Grid 2 Accent 6"/ UnhideWhenUsed="false" Name="Medium Grid 3 Accent 6"/ UnhideWhenUsed="false" Name="Dark List Accent 6"/ UnhideWhenUsed="false" Name="Colorful Shading Accent 6"/ UnhideWhenUsed="false" Name="Colorful List Accent 6"/ UnhideWhenUsed="false" Name="Colorful Grid Accent 6"/ UnhideWhenUsed="false" QFormat="true" Name="Subtle Emphasis"/ UnhideWhenUsed="false" QFormat="true" Name="Intense Emphasis"/ UnhideWhenUsed="false" QFormat="true" Name="Subtle Reference"/ UnhideWhenUsed="false" QFormat="true" Name="Intense Reference"/ UnhideWhenUsed="false" QFormat="true" Name="Book Title"/ classid="clsid:38481807-CA0E-42D2-BF39-B33AF135CC4D" id=ieooui st1\:*{behavior:url(#ieooui) } /* Style Definitions */ table.MsoNormalTable {mso-style-name:????; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Calibri","sans-serif"; mso-bidi-font-family:"Times New Roman";} ??????,????11gR2 ??????gipcd(????ora.gipcd)????,????gipc???,????????????? ????,??oracle????,??????????,??????????,???????????cache fusion ?????????????,?????????????oracle????????????,??????,???????(?????????Note 220970.1:RAC: Frequently Asked Questions,?????????)???????,???????????/????,?????????????? ??,?10gR2 ?11gR1????,?????????????,??:Linux bonding, AIX EtherChannel, HP-UX APA ???????????????????????????????(??,????????????????,???????)???????10g ?11.1 ??????,??????????????????(???????),????????????????subnet??????,????,?????oracle???????????,??????????????,???????????,??????????????,??????????????????????,??:????,?????? ?????????,?11gR2??(????,?11.2.0.2??),oracle??????????????,?????gipc(Grid IPC)???,??????????gipcd.bin?????????,??????? 1. ??????,????????????,?????????,?????????gpnp profile??????????????????? 2. ???????????,??????????,???????????????? 3. ?????????????,?????????/???????????,????????,???????? ??,oracle????????????????????????/??????,??,?????????? ??,???????????????,?????gipc ?HAIP????????????,??????????????,???????????????????:?????????,??:ocssd.bin????,crsd.bin??????;???:oracle RAC ??,??:ASM ??????,?????????????,?????????????????????gipc,???????????,?????????????????????,????????????????,?????,????????????,??,?????????????????gipc???,oracle ??????????????,??????????????,????????????????,HAIP ????,????oracle RAC??????/?????????,????????????????,????,????????HAIP?????,????????????ASM??,?????(???NM??)??????????,?????????????????HAIP,????????,????,???????? “Redundant Interconnect with Highly Available IP (HAIP) ??”? ???,???????????????????????? 1.??????gipcd.log 2013-07-17 12:28:28.071: [ default][3041003216]gipcd START pid=22337 Oracle Grid IPC Daemon 2013-07-17 12:28:28.072: [ GIPCD][3041003216] gipcdMain: gipcd Started <<<<<< gipcd????????? …… 2013-07-17 12:28:29.046: [ GPNP][3041003216]clsgpnp_getCachedProfileEx: [at clsgpnp.c:613] Result: (26) CLSGPNP_NO_PROFILE. Can't get offline GPnP service profile: local gpnpd is up and running. Use getProfile instead. 2013-07-17 12:28:29.046: [ GPNP][3041003216]clsgpnp_getCachedProfileEx: [at clsgpnp.c:623] Result: (26) CLSGPNP_NO_PROFILE. Failed to get offline GPnP service profile. 2013-07-17 12:28:29.066: [ GPNP][3041003216]clsgpnpm_newWiredMsg: [at clsgpnpm.c:741] Msg-reply has soap fault 10 (Operation returned Retry (error CLSGPNP_CALL_AGAIN)) [uri "http://www.grid-pnp.org/2005/12/gpnp-errors#"] <<<< gipcd ????gpnp profile?????????log??GI??????,?????????,?????gpnpd???????? …… 2013-07-17 12:28:39.342: [ CLSINET][3023027088] # 0 Interface 'eth1',ip='192.168.254.30',mac='00-0c-29-a8-14-65',mask='255.255.255.0',net='192.168.254.0',use='cluster_interconnect' 2013-07-17 12:28:39.342: [ CLSINET][3023027088] # 1 Interface 'eth2',ip='192.168.254.31',mac='00-0c-29-a8-14-6f',mask='255.255.255.0',net='192.168.254.0',use='cluster_interconnect' <<<<< gipcd ????????????????,???????2??????????? …… 2013-07-17 12:28:39.344: [GIPCHTHR][3025128336] gipchaWorkerUpdateInterface: created local bootstrap interface for node 'single1', haName 'gipcd_ha_name', inf 'mcast://230.0.1.0:42424/192.168.254.30' 2013-07-17 12:28:39.344: [GIPCHTHR][3025128336] gipchaWorkerUpdateInterface: created local interface for node 'single1', haName 'gipcd_ha_name', inf '192.168.254.30:46782' 2013-07-17 12:28:39.345: [GIPCHTHR][3025128336] gipchaWorkerUpdateInterface: created local bootstrap interface for node 'single1', haName 'gipcd_ha_name', inf 'mcast://230.0.1.0:42424/192.168.254.31' 2013-07-17 12:28:39.345: [GIPCHTHR][3025128336] gipchaWorkerUpdateInterface: created local interface for node 'single1', haName 'gipcd_ha_name', inf '192.168.254.31:39332' <<<<<<< gipcd ????????(????????????????)?endpoint ????? …… 2013-07-17 12:28:56.767: [GIPCHGEN][3023027088] gipchaNodeCreate: adding new node 0x9c107d8 { host 'single2', haName 'gipcd_ha_name', srcLuid 465fb26d-8b46eb95, dstLuid 00000000-00000000 numInf 0, contigSeq 0, lastAck 0, lastValidAck 0, sendSeq [0 : 0], createTime 797327224, flags 0x0 } <<<<< ???????? …… 2013-07-17 12:28:58.415: [GIPCHTHR][3025128336] gipchaWorkerUpdateInterface: created remote interface for node 'single2', haName 'gipcd_ha_name', inf 'udp://192.168.254.33:16663' 2013-07-17 12:28:58.415: [GIPCHGEN][3025128336] gipchaWorkerAttachInterface: Interface attached inf 0x9c0bb60 { host 'single2', haName 'gipcd_ha_name', local 0xb4c4e590, ip '192.168.254.33:16663', subnet '192.168.254.0', mask '255.255.255.0', numRef 0, numFail 0, flags 0x6 } 2013-07-17 12:28:58.415: [GIPCHTHR][3025128336] gipchaWorkerUpdateInterface: created remote interface for node 'single2', haName 'gipcd_ha_name', inf 'udp://192.168.254.32:17578' 2013-07-17 12:28:58.415: [GIPCHGEN][3025128336] gipchaWorkerAttachInterface: Interface attached inf 0x9c0a900 { host 'single2', haName 'gipcd_ha_name', local 0xb4cb8eb8, ip '192.168.254.32:17578', subnet '192.168.254.0', mask '255.255.255.0', numRef 0, numFail 0, flags 0x6 } <<<<<< gipcd ??????????????? …… 2013-07-17 12:29:36.120: [GIPCDMON][3027229584] gipcdMonitorSaveInfMetrics: inf[ 0] eth1 - rank 99, avgms 6.326531 [ 257 / 250 / 245 ] 2013-07-17 12:29:36.120: [GIPCDMON][3027229584] gipcdMonitorSaveInfMetrics: inf[ 1] eth2 - rank 99, avgms 5.182186 [ 259 / 250 / 247 ] <<<<<gipcd ??????????? ……  2. ?????????down???gipcd.log? 2013-07-17 13:23:20.346: [ CLSINET][3027229584] Returning NETDATA: 2 interfaces 2013-07-17 13:23:20.346: [ CLSINET][3027229584] # 0 Interface 'eth1',ip='192.168.254.30',mac='00-0c-29-a8-14-65',mask='255.255.255.0',net='192.168.254.0',use='cluster_interconnect' 2013-07-17 13:23:20.346: [ CLSINET][3027229584] # 1 Interface 'eth2',ip='192.168.254.31',mac='00-0c-29-a8-14-6f',mask='255.255.255.0',net='192.168.254.0',use='cluster_interconnect' 2013-07-17 13:23:20.359: [GIPCDMON][3027229584] gipcdMonitorSaveInfMetrics: inf[ 0] eth1 - rank 99, avgms 1.560694 [ 171 / 173 / 173 ] 2013-07-17 13:23:20.359: [GIPCDMON][3027229584] gipcdMonitorSaveInfMetrics: inf[ 1] eth2 - rank 99, avgms 1.802326 [ 172 / 172 / 172 ] <<<<<<<< gipcd ?????????? …… +++????“ifconfig eth1 down”????????????? …… 2013-07-17 13:23:44.397: [ CLSINET][3027229584] # 0 Interface 'eth2',ip='192.168.254.31',mac='00-0c-29-a8-14-6f',mask='255.255.255.0',net='192.168.254.0',use='cluster_interconnect' 2013-07-17 13:23:44.397: [GIPCDMON][3027229584] gipcdMonitorUpdate: interface went down - [ ip 192.168.254.30, subnet 192.168.254.0, mask 255.255.255.0 ] 2013-07-17 13:23:44.397: [GIPCDMON][3027229584] gipcdMonitorUpdate: msg sent to client thread (([update(ip: 192.168.254.30, mask: 255.255.255.0, subnet 192.168.254.0), state(gipcdadapterstateDown)])) <<<<<<<< gipcd ????eth1 down?,???????(??:ocssd.bin)????? …… 2013-07-17 13:23:44.426: [GIPCHGEN][3025128336] gipchaInterfaceDisable: disabling interface 0xb4c4e590 { host '', haName 'gipcd_ha_name', local (nil), ip '192.168.254.30', subnet '192.168.254.0', mask '255.255.255.0', numRef 0, numFail 1, flags 0x1cd } 2013-07-17 13:23:44.428: [GIPCHGEN][3025128336] gipchaInterfaceDisable: disabling interface 0x9c0bb60 { host 'single2', haName 'gipcd_ha_name', local 0xb4c4e590, ip '192.168.254.33:16663', subnet '192.168.254.0', mask '255.255.255.0', numRef 0, numFail 0, flags 0x86 } 2013-07-17 13:23:44.428: [GIPCHALO][3025128336] gipchaLowerCleanInterfaces: performing cleanup of disabled interface 0x9c0bb60 { host 'single2', haName 'gipcd_ha_name', local 0xb4c4e590, ip '192.168.254.33:16663', subnet '192.168.254.0', mask '255.255.255.0', numRef 0, numFail 0, flags 0xa6 } <<<<<<<<gipcd ????????eth1 ???,????????????????????? …… 2013-07-17 13:24:08.747: [GIPCDMON][3027229584] gipcdMonitorSaveInfMetrics: inf[ 0] eth2 - rank 99, avgms 1.955307 [ 204 / 181 / 179 ] <<<<<<<gipcd ???????????? ??:??????,??????????????????,????????????????,???????????eth1??HAIP,?failover?eth2 ?,????,????ASM??????? 3. ???eht1???? ++ ????”ifconfig eth1 up”????eth1 2013-07-17 13:36:31.260: [GIPCDMON][3027229584] gipcdMonitorUpdate: New Interface found - [ ip 192.168.254.30, subnet 192.168.254.0, mask 255.255.255.0 ] 2013-07-17 13:36:31.260: [GIPCDMON][3027229584] gipcdMonitorUpdate: msg sent to client thread (([update(ip: 192.168.254.30, mask: 255.255.255.0, subnet 192.168.254.0), state(gipcdadapterstateUp)])) <<<<< gpicd ?????????? …… 2013-07-17 13:36:31.471: [GIPCHTHR][3025128336] gipchaWorkerUpdateInterface: created local bootstrap interface for node 'single1', haName 'gipcd_ha_name', inf 'mcast://230.0.1.0:42424/192.168.254.30' 2013-07-17 13:36:31.471: [GIPCHTHR][3025128336] gipchaWorkerUpdateInterface: created local interface for node 'single1', haName 'gipcd_ha_name', inf '192.168.254.30:55548' <<<<<< ?????endpoint???? …… 2013-07-17 13:37:11.493: [ CLSINET][3027229584] Returning NETDATA: 2 interfaces 2013-07-17 13:37:11.493: [ CLSINET][3027229584] # 0 Interface 'eth1',ip='192.168.254.30',mac='00-0c-29-a8-14-65',mask='255.255.255.0',net='192.168.254.0',use='cluster_interconnect' 2013-07-17 13:37:11.493: [ CLSINET][3027229584] # 1 Interface 'eth2',ip='192.168.254.31',mac='00-0c-29-a8-14-6f',mask='255.255.255.0',net='192.168.254.0',use='cluster_interconnect' 2013-07-17 13:37:11.510: [GIPCDMON][3027229584] gipcdMonitorSaveInfMetrics: inf[ 0] eth2 - rank 99, avgms 6.141304 [ 307 / 184 / 184 ] <<<<<<<< <<<<<<<< gipcd??????? ??:??????,??????????????????,????????????????,????????failover?eth2??HAIP,?????eth1 ?,????,????ASM??????? ??,????????,gipcd ???????????,??,????????,?????????(????)????,gipcd???????????,??????HAIP???,???????????????(??:Linux bonding,etherchannel?),???????????,????????? ??????????????11gR2 ??????gipcd????,????????????,?????????? ??????????,???????????,??“??:11gR2???---gipc????"?

  Read the article

• Fun with Sun Ray, 3D, Oracle VM x86 and SRIOV

  - by wim.coekaerts

  One of the things I like about my job is that I get to play around with stuff and make use of the technologies we work on in my teams. Sort of my own little playground. It allows me to study the products in great detail and put them to use in ways that individual product teams don't always intend them to be used for :) but that makes it fun. I have a lot of this set up at home because... work is sort of hobby and I just like to tinker with it. Anyway, a few weeks ago I was looking at my sun ray rig at home and how well 3D works. Google Earth and some basic opengl tests like glxspheres combined with virtualgl. It resulted in some very cool demos recorded with my little camera (sorry for the crappy quality of the video :-) : OVDC (soft client) on my mac Sun Ray 2FS Never mind the hickups during zoom, that's because I was using the scrollwheel on my mouse and I can't scroll uninterrupted :) Anyway, this is quite cool ! The setup for this was the following : Sun Ray on LAN, Sun Ray Server 5 latest installed on OL5.5 inside a VM running on Oracle VM 2.2 (hardware virt, with a virtual network (vif)) and the virtualgl rendering happened on another box (wopr5) that runs linux on a little atom D520 with an ION2 gpu. So network goes from Sun Ray to Sun Ray Server to wopr5 and back. Given that this is full screen 3D it puts a good amount of load on the network and it's pretty cool that SRS was just a VM :) So, separately, I had written a little blog entry about using sriov and oracle vm a while back. link to sriov blog entry Last night when I came home I wanted to do some more playing around with SRIOV and live migrate. To do this, I wanted to set up a VM with 2 network interfaces, one virtual network (vif) and then one that's one of the SRIOV virtual functions from my network card. Inside the guest they show as eth0 and eth1, and then bond them using a standard linux bonding device (bond0 here) with active active links. The goal here is that on live migrate, we would detach the VF (eth1 in guest in this case), the bond would then just hum along on eth0 (vif) we can live migrate the VM and then on the other server after the migrate completes we re-attach a VF to the VM there and eth1 pops up again and the bond uses both eth0/eth1 to do its work. So, to set this up, I figured, why not use my sun ray server VM because the 3D work generates a nice network load and is very latency/timing sensitive. In the end, I ran glxspheres on my sunray server (vm) displaying on my sun ray 2 fs and while that was running, I did my live migrate test of this vm (unplug pci VF, migrate, reconnect vf) and guess what, it just kept running :) veryyyyyy cool. now, it was supposed to, but it's always nice to see it actually work, for real. Here's a diagram of it. No gimics - just real technology at work ! enjoy :)

  Read the article

• Virtualized data centre&ndash;Part four: The design

  - by marc dekeyser

  Welcome back to the fourth post in this series! Today we will have a look at what Microsoft recommends as a “private cloud design” and what I will make of it. Whilst my own solution is based of the reference architecture, it is quite different indeed! An important thing to know is that, whilst I am using the private cloud as a reference, I am skipping most of the steps in designing a private cloud. If that is why you are here, please read the links at the end of the article and skim through my own content. A private cloud is much more process driven than just building a virtual infrastructure… The architecture of it all… So imagine for a minute that you have unlimited funds to build this lab of yours… You’d want redundancy on all levels and separation of each network where possible! Unfortunately we don’t have that luxury and, as you saw me hinting at in the previous article, our own design will be more limited but still quite capable! Networking From the networking perspective I will not have a fully redundant network, after all, this is but a lab environment! Thanks to Server 2012 I will be able to use bonding on my NIC’s and use LACP to improve the performance on that part. Storage As I mentioned in the previous article a Synology DS1218+ will be used for iSCSI provisioning. This device has 2 NICs on-board which can be bonded in to one 2 Gbps interface giving me a decent throughput and making the disks the most limiting factor in the storage design. Domain controllers and extra infrastructure Server 2012 completely supports running domain controllers virtualized and has no need to actually have a reachable DC when booting… That being said I need a remote access machine to power on the hosts (I have no need for them running 24/7) and a possible System Center VMM 2012 box (although server 2012 is not supported until SP1 :( ). Undecided on if I am to install those boxes separately or as a virtual machine… Which amounts to… Something like this pretty picture!                   Sources Microsoft Private Cloud Solutions Repository (en-US) http://social.technet.microsoft.com/wiki/contents/articles/12131.microsoft-private-cloud-solutions-repository-en-us.aspx Reference  Architecture: http://social.technet.microsoft.com/wiki/contents/articles/3819.reference-architecture-for-private-cloud.aspx Private Cloud Reference Model: http://social.technet.microsoft.com/wiki/contents/articles/4399.private-cloud-reference-model.aspx

  Read the article

• Setting MTU on Exalogic

  - by csoto

  For many reasons, a system administrator may want to change the MTU settings of a server. But in a system like Exalogic which contains lots of interconnected nodes and other various components, it's important to understand how this applies to the different networks. For example, when bringing up bonding of InfiniBand an error like the following may be thrown: Bringing up interface bond1: SIOCSIFMTU: Invalid argument Both scripts ifcfg-ib0 and ifcfg-ib1 (from the /etc/sysconfig/network-scripts/ direectory) have MTU set to 65500, which is a valid MTU value only if all IPoIB slaves operate in connected mode and are configured with the same value, so the line below must be added to both network scripts and then restart the network: CONNECTED_MODE=yes By the way, an error of the form “SIOCSIFMTU: Invalid argument” indicates that the requested MTU was rejected by the kernel. Typically this would be due to it exceeding the maximum value supported by the interface hardware. In that case you must either reduce the MTU to a value that is supported or obtain more capable hardware. This problem has been seen when trying to modify the MTU using the ifconfig command, like the output of the example below: [root@elxxcnxx ~]# ifconfig ib1 mtu 65520 SIOCSIFMTU: Invalid argument It's important to insist that in most cases the nodes must be rebooted after the MTU size has been changed. Although in some circumstances it may work without a reboot, it is not how it is typically documented. Now, in order to achieve a reduced memory consumption and improve performance for network traffic received on IPoIB related interfaces, it is recommend to reduce the MTU value in interface configuration files for IPoIB related bonds from 65520 to 64000. The change needs to be made to interface configuration files under the /etc/sysconfig/network-scripts directory and applies to the interface configuration files for bonds over IPoIB related slave devices, for example /etc/sysconfig/network-scripts/ifcfg-bond1. However, keep in mind that the numeric portion of the interface filenames that corresponding to IPoIB interfaces is expected to vary across compute nodes and vServers and so cannot be relied upon to identify which interface files are for bonds are over IPoIB rather than EoIB related slave interfaces. To fix these MTU values to the recommended settings, there are very useful instructions and a script on the MOS Note 1624434.1, and it's applicable physical and virtual configurations of Exalogic. Regarding the recommended MTU value for EoIB related interfaces, its maximum appropriate value is 1500. If for some reason a vServer has been created with a higher value (set on the /etc/sysconfig/network-scripts/ifcfg-bond0 file), then it must be fixed. An error like the following could be thrown under this circumstance: [root@vServer ~]# service network restart ... Bringing up interface bond0:  SIOCSIFMTU: Invalid argument Also an error like the one below can be seen on the /var/log/messages file of the vServer: kernel: T5074835532 [mlx4_vnic] eth1:vnic_change_mtu:360: failed: new_mtu 64000 2026 The MOS Note 1611657.1 is very useful for this purpose.

  Read the article

• Openfiler iSCSI performance

  - by Justin

  Hoping someone can point me in the right direction with some iSCSI performance issues I'm having. I'm running Openfiler 2.99 on an older ProLiant DL360 G5. Dual Xeon processor, 6GB ECC RAM, Intel Gigabit Server NIC, SAS controller with and 3 10K SAS drives in a RAID 5. When I run a simple write test from the box directly the performance is very good: [root@localhost ~]# dd if=/dev/zero of=tmpfile bs=1M count=1000 1000+0 records in 1000+0 records out 1048576000 bytes (1.0 GB) copied, 4.64468 s, 226 MB/s So I created a LUN, attached it to another box I have running ESXi 5.1 (Core i7 2600k, 16GB RAM, Intel Gigabit Server NIC) and created a new datastore. Once I created the datastore I was able to create and start a VM running CentOS with 2GB of RAM and 16GB of disk space. The OS installed fine and I'm able to use it but when I ran the same test inside the VM I get dramatically different results: [root@localhost ~]# dd if=/dev/zero of=tmpfile bs=1M count=1000 1000+0 records in 1000+0 records out 1048576000 bytes (1.0 GB) copied, 26.8786 s, 39.0 MB/s [root@localhost ~]# Both servers have brand new Intel Server NIC's and I have Jumbo Frames enabled on the switch, the openfiler box as well as the VMKernel adapter on the ESXi box. I can confirm this is set up properly by using the vmkping command from the ESXi host: ~ # vmkping 10.0.0.1 -s 9000 PING 10.0.0.1 (10.0.0.1): 9000 data bytes 9008 bytes from 10.0.0.1: icmp_seq=0 ttl=64 time=0.533 ms 9008 bytes from 10.0.0.1: icmp_seq=1 ttl=64 time=0.736 ms 9008 bytes from 10.0.0.1: icmp_seq=2 ttl=64 time=0.570 ms The only thing I haven't tried as far as networking goes is bonding two interfaces together. I'm open to trying that down the road but for now I am trying to keep things simple. I know this is a pretty modest setup and I'm not expecting top notch performance but I would like to see 90-100MB/s. Any ideas?

  Read the article

• Improving abysmal 802.11n wireless network

  - by concept

  I am in desperate need of help to improve the abysmal performance of my 802.11n wireless network. At best I get 30Mbs (this is an internet download) from a technology that boasts 300Mbs, even worse is the LAN where to date best i have ever gotten is 1Mbs. It is literally quicker to copy the file to a USB and walk it to the other computer. Infrastructure is this AP 802.11n only broadcasting at both 2.4GHz and 5GHz Mac with 802.11a/b/g/n card is connected to the AP via 5GHz Linux with 802.11a/b/g/n card is connected to AP via 2.4GHz I have conducted the following tests (results at end of post) Internet based speed test wired and wireless LAN file copy wired and wireless I have read: http://nutsaboutnets.com/troubleshooting-wi-fi-problems/ http://www.smallnetbuilder.com/wireless/wireless-basics/30664-5-ways-to-fix-slow-80211n-- speed http colon //www.wi-fiplanet dot com/tutorials/7-tips-to-increase-wi-fi-performance.html Slow file transfer on network between two 802.11n laptops (connected directly together via access point) Wireless Network Performance Issues Slower than expected 802.11n wireless network speeds I have made the following optimizations AP broadcasts only 802.11n on both 2.4GHz and 5GHz frequencies 2.4GHz is on a channel with least interference (live in an apartment with lots of APs), this did make a 10Mb/sec improvement Our AP is the only one transmitting on the 5GHz freq. Security: WPA Personal WPA2 AES encryption Bandwidth: 20MHz / 40MHz (i assume this to be channel bonding) I have tried the following with 0 improvement Dropped the Fragment Threshold to 512 Dropped the Request To Send (RTS) Threshold to 512 and 1 Even thought of buying a frequency spectrum analyzer, until i saw the cost of them!!! Speed test results Linux Wired: DOWNLOAD 128.40Mb/s UPLOAD 10.62Mb/s www dot speedtest dot net/my-result/2948381853 Mac Wired: DOWNLOAD 118.02Mb/s UPLOAD 10.56Mb/s www dot speedtest dot net/my-result/2948384406 Linux Wireless: DOWNLOAD 23.99Mb/s UPLOAD 10.31Mb/s www.speedtest dot net/my-result/2948394990 Mac Wireless: DOWNLOAD 22.55Mb/s UPLOAD 10.36Mb/s www.speedtest dot net/my-result/2948396489 LAN NFS 53,345,087 bytes (51Mb) file Linux Mac NFS Wired: 65.6959 Mb/sec Linux Mac NFS Wireless: .9443 Mb/sec All help is appreciated, even testing methods will be accepted.

  Read the article

• VPN Trunk Between Cisco ASA 5520 and DrayTek Vigor 2930

  - by David Heggie

  I'm a bit of a VPN newbie, so please go easy on me ... I'm trying to use the VPN trunking capabilities of the DrayTek Vigor 2930 firewall to bond two IPSec VPN connections to a Cisco ASA 5520 device and I'm getting myself tied in knots and hope someone here with more knowledge / experience can help. I have a remote site with two ADSL connections and the DrayTek box. The main office site has the Cisco ASA device. I am able to setup a single IPSec connection between the two sites on either of the ADSL connections' public IP addresses, but as soon as I try to use the VPN bonding, nothing works. The VPN tunnels are both still up, but the traffic is getting lost somewhere. I suspect it's due to the ASA not knowing how to route the traffic back over the VPN - one minute, traffic from my remote office's network is coming from public ip address #1, the next it's coming from public address #2 and it doesn't know what to do. Well, that's my newbie impression of what's going wrong, but I don't really know: If this is really what's happening If what I'm trying to do (bond two VPN connections from a single remote network to improve the bandwidth / resiliency) is possible with the kit I've got Could anyone help?

  Read the article

• How important is dual-gigabit lan for a super user's home NAS?

  - by Andrew

  Long story short: I'm building my own home server based on Ubuntu with 4 drives in RAID 10. Its primary purpose will be NAS and backup. Would I be making a terrible mistake by building a NAS Server with a single Gigabit NIC? Long story long: I know the absolute max I can get out of a single Gigabit port is 125MB/s, and I want this NAS to be able to handle up to 6 computers accessing files simultaneously, with up to two of them streaming video. With Ubuntu NIC-bonding and the performance of RAID 10, I can theoretically double my throughput and achieve 250MB/s (ok, not really, but it would be faster). The drives have an average read throughput of 83.87MB/s according to Tom's Hardware. The unit itself will be based on the Chenbro ES34069-BK-180 case. With my current hardware choices, it'll have this motherboard with a Core i3 CPU and 8GB of RAM. Overkill, I know, but this server will be doing other things as well (like transcoding video). Unfortunately, the only Mini-ITX boards I can find with dual-gigabit and 6 SATA ports are Intel Atom-based, and I need more processing power than an Atom has to offer. I would love to find a board with 6 SATA ports and two Gigabit LAN ports that supports a Core i3 CPU. So far, my search has come up empty. Thus, my dilemma. Should I hold out for such a board, go with an Atom-based solution, or stick with my current single-gigabit configuration? I know there are consumer NAS units with just one gigabit interface (probably most of them), but I think I will demand a lot more from my server than the average home user. Any advice is appreciated. Thanks.

  Read the article

• bluez 5.19 PS4 controller

  - by Athanase

  I currently have a problem when pairing my computer with a PS4 remote. On my Ubuntu 14.04 I removed everything related with bluez and bluetooth, and I built and installed bluez 5.19. Here are some useful command outputs: jean@system ~ hcitool hcitool - HCI Tool ver 5.19 jean@system ~ hcitool dev Devices: hci0 00:15:83:4C:0C:BB jean@system ~ bluetoothctl [bluetooth]# version Version 5.19 jean@system ~ bluetoothctl [NEW] Controller 00:15:83:4C:0C:BB BlueZ [default] jean@system ~ lsusb Bus 003 Device 012: ID 0a12:0001 Cambridge Silicon Radio, Ltd Bluetooth Dongle (HCI mode) So here is what happens. When I try to hard pair the controller with the computer, by holding the share and ps button for a while, everything works as expected and the pairing is done properly. After a hard pairing if I try the pairing by pressing the ps button only, nothings happen. In order to go it, I first power up the bluetooth dongle: jean@system ~ sudo hciconfig hciX up and then I run the bluetooh deamon bluetoothd: jean@system /usr/libexec/bluetooth ~ ./bluetoothd -d -n bluetoothd[11270]: Bluetooth daemon 5.19 bluetoothd[11270]: src/main.c:parse_config() parsing main.conf bluetoothd[11270]: src/main.c:parse_config() discovto=0 bluetoothd[11270]: src/main.c:parse_config() pairto=0 bluetoothd[11270]: src/main.c:parse_config() auto_to=60 bluetoothd[11270]: src/main.c:parse_config() name=%h-%d bluetoothd[11270]: src/main.c:parse_config() class=0x000100 bluetoothd[11270]: src/main.c:parse_config() Key file does not have key 'DeviceID' bluetoothd[11270]: src/gatt.c:gatt_init() Starting GATT server bluetoothd[11270]: src/adapter.c:adapter_init() sending read version command bluetoothd[11270]: Starting SDP server bluetoothd[11270]: src/sdpd-service.c:register_device_id() Adding device id record for 0002:1d6b:0246:0513 ... bluetoothd[11270]: src/adapter.c:adapter_service_insert() /org/bluez/hci0 bluetoothd[11270]: src/adapter.c:add_uuid() sending add uuid command for index 0 bluetoothd[11270]: profiles/audio/a2dp.c:a2dp_sink_server_probe() path /org/bluez/hci0 bluetoothd[11270]: profiles/audio/a2dp.c:a2dp_source_server_probe() path /org/bluez/hci0 bluetoothd[11270]: src/adapter.c:btd_adapter_unblock_address() hci0 00:00:00:00:00:00 bluetoothd[11270]: src/adapter.c:get_ltk_info() A4:15:66:C1:0D:2A bluetoothd[11270]: src/device.c:device_create_from_storage() address A4:15:66:C1:0D:2A bluetoothd[11270]: src/device.c:device_new() address A4:15:66:C1:0D:2A bluetoothd[11270]: src/device.c:device_new() Creating device /org/bluez/hci0/dev_A4_15_66_C1_0D_2A bluetoothd[11270]: src/device.c:device_set_bonded() bluetoothd[11270]: src/adapter.c:get_ltk_info() A4:15:66:88:5E:9A bluetoothd[11270]: src/device.c:device_create_from_storage() address A4:15:66:88:5E:9A bluetoothd[11270]: src/device.c:device_new() address A4:15:66:88:5E:9A bluetoothd[11270]: src/device.c:device_new() Creating device /org/bluez/hci0/dev_A4_15_66_88_5E_9A bluetoothd[11270]: src/device.c:device_set_bonded() bluetoothd[11270]: src/adapter.c:load_link_keys() hci0 keys 2 debug_keys 0 bluetoothd[11270]: src/adapter.c:load_ltks() hci0 keys 0 bluetoothd[11270]: src/adapter.c:load_connections() sending get connections command for index 0 bluetoothd[11270]: src/adapter.c:adapter_service_insert() /org/bluez/hci0 bluetoothd[11270]: src/adapter.c:add_uuid() sending add uuid command for index 0 bluetoothd[11270]: src/adapter.c:set_did() hci0 source 2 vendor 1d6b product 246 version 513 bluetoothd[11270]: src/adapter.c:adapter_register() Adapter /org/bluez/hci0 registered bluetoothd[11270]: src/adapter.c:set_dev_class() sending set device class command for index 0 bluetoothd[11270]: src/adapter.c:set_name() sending set local name command for index 0 bluetoothd[11270]: src/adapter.c:set_mode() sending set mode command for index 0 bluetoothd[11270]: src/adapter.c:set_mode() sending set mode command for index 0 bluetoothd[11270]: src/adapter.c:adapter_start() adapter /org/bluez/hci0 has been enabled bluetoothd[11270]: src/adapter.c:trigger_passive_scanning() bluetoothd[11270]: plugins/hostname.c:property_changed() static hostname: system bluetoothd[11270]: plugins/hostname.c:property_changed() pretty hostname: bluetoothd[11270]: plugins/hostname.c:update_name() name: system bluetoothd[11270]: src/adapter.c:adapter_set_name() name: system bluetoothd[11270]: plugins/hostname.c:property_changed() chassis: desktop bluetoothd[11270]: plugins/hostname.c:update_class() major: 0x01 minor: 0x01 bluetoothd[11270]: src/adapter.c:load_link_keys_complete() link keys loaded for hci0 bluetoothd[11270]: src/adapter.c:load_ltks_complete() LTKs loaded for hci0 bluetoothd[11270]: src/adapter.c:get_connections_complete() Connection count: 0 And then I press the ps button of the PS4 controller bluetoothd[11270]: src/adapter.c:connected_callback() hci0 device A4:15:66:C1:0D:2A connected eir_len 5 bluetoothd[11270]: profiles/input/server.c:connect_event_cb() Incoming connection from A4:15:66:C1:0D:2A on PSM 17 bluetoothd[11270]: profiles/input/device.c:input_device_set_channel() idev (nil) psm 17 bluetoothd[11270]: Refusing input device connect: No such file or directory (2) bluetoothd[11270]: profiles/input/server.c:confirm_event_cb() bluetoothd[11270]: Refusing connection from A4:15:66:C1:0D:2A: unknown device bluetoothd[11270]: src/adapter.c:dev_disconnected() Device A4:15:66:C1:0D:2A disconnected, reason 3 bluetoothd[11270]: src/adapter.c:adapter_remove_connection() bluetoothd[11270]: plugins/policy.c:disconnect_cb() reason 3 bluetoothd[11270]: src/adapter.c:bonding_attempt_complete() hci0 bdaddr A4:15:66:C1:0D:2A type 0 status 0xe bluetoothd[11270]: src/device.c:device_bonding_complete() bonding (nil) status 0x0e bluetoothd[11270]: src/device.c:device_bonding_failed() status 14 bluetoothd[11270]: src/adapter.c:resume_discovery() So I don't know what is happening here and a bit of help would be appreciated.

  Read the article

• Cobbler 2.2.2 problems

  - by Peter

  I have setup a dedicated LAN for Cobbler tests. My setup is: Cobbler server: openSUSE 12.3, cobbler 2.2.2 (from openSUSE repos) Imported distros: Centos 6.5, Red Hat 6.5, Red Hat 7.0, openSUSE 13.1 Target Machine: VMs in a Windows 7 Virtualbox Systems provisioning works OK, but I have some problems. The first one is that cobbler does not honor the "pxe_just_once: 1" setting. When the setup of the target OS is finished, after the reboot the target systems continues to PXE boot! The second problem is that the target server is not correctly configured! See my setup: cobbler system report --name=test Name : test TFTP Boot Files : {} Comment : Fetchable Files : {} Gateway : 192.168.0.1 Hostname : testcob1.example.com Image : IPv6 Autoconfiguration : False IPv6 Default Device : Kernel Options : {} Kernel Options (Post Install) : {} Kickstart : <<inherit>> Kickstart Metadata : {} LDAP Enabled : False LDAP Management Type : authconfig Management Classes : [] Management Parameters : <<inherit>> Monit Enabled : False Name Servers : ['192.168.0.1', '8.8.8.8'] Name Servers Search Path : [] Netboot Enabled : False Owners : ['admin'] Power Management Address : Power ID : Power Password : Power Management Type : ipmitool Power Username : Profile : RHEL-6.5-x86_64 Proxy : <<inherit>> Red Hat Management Key : <<inherit>> Red Hat Management Server : <<inherit>> Repos Enabled : False Server Override : <<inherit>> Status : testing Template Files : {} Virt Auto Boot : <<inherit>> Virt CPUs : <<inherit>> Virt Disk Driver Type : <<inherit>> Virt File Size(GB) : <<inherit>> Virt Path : <<inherit>> Virt RAM (MB) : <<inherit>> Virt Type : <<inherit>> Interface ===== : eth0 Bonding Opts : Bridge Opts : DHCP Tag : DNS Name : Master Interface : Interface Type : IP Address : 192.168.0.200 IPv6 Address : IPv6 Default Gateway : IPv6 MTU : IPv6 Secondaries : [] IPv6 Static Routes : [] MAC Address : Management Interface : True MTU : Subnet Mask : 255.255.255.0 Static : True Static Routes : [] Virt Bridge : So, although I have setup the hostname and the network interface of the target system, after the setup, the hostname is set to localhost.localdomain and eth0 is configured as a DHCP not static! How can I find the problem and fix it? Note that I have synced and restarted cobbler a couple of times, but the problems persists.

  Read the article

• Can't ping Ip over bridge

  - by tmn29a

  I'm unable to ping another host over a bridge I created, I can't see the error -.- It's a remote machine running debian stable with some backports for which I want to set up DHCP on the new Subnet 172.30.xxx.xxx to be used for KVM-Guests. ifconfig : bond0 Link encap:Ethernet HWaddr e4:11:5b:d4:94:30 inet addr:10.54.2.84 Bcast:10.54.2.127 Mask:255.255.255.192 inet6 addr: fe80::e611:5bff:fed4:9430/64 Scope:Link UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:34277 errors:0 dropped:0 overruns:0 frame:0 TX packets:18379 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2638709 (2.5 MiB) TX bytes:2887894 (2.7 MiB) br0 Link encap:Ethernet HWaddr f2:fc:4d:7f:15:f0 inet addr:172.30.254.66 Bcast:172.30.254.127 Mask:255.255.255.192 inet6 addr: fe80::f0fc:4dff:fe7f:15f0/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:252 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:10800 (10.5 KiB) Pings : ping -I br0 172.30.xxx.65 PING 172.30.xxx.65 (172.30.xxx.65) from 172.30.xxx.66 br0: 56(84) bytes of data. --- 172.30.xxx.65 ping statistics --- 3 packets transmitted, 0 received, 100% packet loss, time 2017ms ping -I bond0 172.30.254.65 PING 172.30.xxx.65 (172.30.xxx.65) from 10.54.2.84 bond0: 56(84) bytes of data. 64 bytes from 172.30.x.65: icmp_req=1 ttl=64 time=0.599 ms 64 bytes from 172.30.x.65: icmp_req=2 ttl=64 time=0.575 ms 64 bytes from 172.30.x.65: icmp_req=3 ttl=64 time=0.565 ms --- 172.30.x.65 ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 1999ms rtt min/avg/max/mdev = 0.565/0.579/0.599/0.031 ms Route : Destination Gateway Genmask Flags Metric Ref Use Iface 172.30.x.64 * 255.255.255.192 U 0 0 0 br0 10.54.x.64 * 255.255.255.192 U 0 0 0 bond0 default 10.54.x.65 0.0.0.0 UG 0 0 0 bond0 default 172.30.x.65 0.0.0.0 UG 0 0 0 br0 The Interface : cat /etc/network/interfaces auto lo br0 iface lo inet loopback # Bonding Interface auto bond0 iface bond0 inet static address 10.54.x.84 netmask 255.255.255.192 network 10.54.x.64 gateway 10.54.x.65 slaves eth0 eth1 bond_mode active-backup bond_miimon 100 bond_downdelay 200 bond_updelay 200 iface br0 inet static bridge_ports bond0 address 172.30.x.66 broadcast 172.30.x.127 netmask 255.255.x.192 gateway 172.30.x.65 bridge_maxwait 0 If you need more info please ask. Thanks for your help !

  Read the article

• Not so long ago in a city not so far away by Carlos Martin

  - by Maria Sandu

  Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 This is the story of how the EMEA Presales Center turned an Oracle intern into a trusted technology advisor for both Oracle’s Sales and customers. It was the summer of 2011 when I was finishing my Computer Engineering studies as well as my internship at Oracle when I was offered what could possibly be THE dream job for any young European Computer Engineer. Apart from that, it also seemed like the role was particularly tailored to me as I could leverage almost everything I learned at University and during the internship. And all of it in one of the best cities to live in, not only from my home country but arguably from Europe: Malaga! A day at EPC As part of the EPC Technology pillar, and later on completely focused on WebCenter, there was no way to describe a normal day on the job as each day had something unique. Some days I was researching documentation in order to elaborate accurate answers for a customer’s question within a Request for Information or Proposal (RFI/RFP), other days I was doing heavy programming in order to bring a Proof of Concept (PoC) for a customer to life and last not but least, some days I presented to the customer via webconference the demo I built for them the past weeks. So as you can see, the role has research, development and presentation, could you ask for more? Well, don’t worry because there IS more! Internationality As the organization’s name suggests, EMEA Presales Center, it is the Center of Presales within Europe, Middle East and Africa so I got the chance to work with great professionals from all this regions, expanding my network and learning things from one country to apply them to others. In addition to that, the teams based in the Malaga office are comprised of many young professionals hailing mainly from Western and Central European countries (although there are a couple of exceptions!) with very different backgrounds and personalities which guaranteed many laughs and stories during lunch or coffee breaks (or even while working on projects!). Furthermore, having EPC offices in Bucharest and Bangalore and thanks to today’s tele-presence technologies, I was working every day with people from India or Romania as if they were sitting right next to me and the bonding with them got stronger day by day. Career development Apart from the research and self-study I’ve earlier mentioned, one of the EPC’s Key Performance Indicators (KPI) is that 15% of your time is spent on training so you get lots and lots of trainings in order to develop both your technical product knowledge and your presentation, negotiation and other soft skills. Sometimes the training is via webcast, sometimes the trainer comes to the office and sometimes, the best times, you get to travel abroad in order to attend a training, which also helps you to further develop your network by meeting face to face with many people you only know from some email or instant messaging interaction. And as the months go by, your skills improving at a very fast pace, your relevance increasing with each new project you successfully deliver, it’s only a matter of time (and a bit of self-promoting!) that you get the attention of the manager of a more senior team and are offered the opportunity to take a new step in your professional career. For me it took 2 years to move to my current position, Technology Sales Consultant at the Oracle Direct organization. During those 2 years I had built a good relationship with the Oracle Direct Spanish sales and sales managers, who are also based in the Malaga office. I supported their former Sales Consultant in a couple of presentations and demos and were very happy with my overall performance and attitude so even before the position got eventually vacant, I got a heads-up from then in advance that their current Sales Consultant was going to move to a different position. To me it felt like a natural step, same as when I joined EPC, I had at least a 50% of the “homework” already done but wanted to experience that extra 50% to add new product and soft skills to my arsenal. The rest is history, I’ve been in the role for more than half a year as I’m writing this, achieved already some important wins, gained a lot of trust and confidence in front of customers and broadened my view of Oracle’s Fusion Middleware portfolio. I look back at the 2 years I spent in EPC and think: “boy, I’d recommend that experience to absolutely anyone with the slightest interest in IT, there are so many different things you can do as there are different kind of roles you can end up taking thanks to the experience gained at EPC” /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin-top:0in; mso-para-margin-right:0in; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0in; line-height:115%; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;}

  Read the article

< Previous Page | 1 2 3  | Next Page >