Search Results

Search found 12829 results on 514 pages for 'hard'.

Page 2/514 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• Accessing second hard drive

  - by Jonathan

  Hi, So I recently installed Ubuntu 10.10 64-bit on my computer. I installed it on my 60gb SSD hard drive, and in the installation it never acknowledged the existence of my second hard drive. The hard drive that I keep all my files on, and which I want to make my home folder if I can, is a Western Digital Caviar Black 1TB SATA 6Gb/s 64MB cache (WD1002FAEX). I've read the following: https://help.ubuntu.com/community/Mount but honestly cannot work out how to access the hard drive from my Ubuntu installation. I did have Windows 7 64-bit prior to installing Ubuntu. I have backed up all the files on the hard drive, but if I could just access them straight off that would be super cool. Does anyone know how I can use the second hard drive? Thank you for your help EDIT: The following directories are currently in my /dev/ folder: ati/, block/, bsg/, bus/, char/, cpu/, isk/, input/, mapper/, net/, pktcdvd/, pts/, shm/, snd/, and usb/ EDIT: Result from sudo fdisk -l Disk /dev/sda: 60.0 GB, 60022480896 bytes 255 heads, 63 sectors/track, 7297 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000d2dfd Device Boot Start End Blocks Id System /dev/sda1 * 1 6994 56174592 83 Linux /dev/sda2 6994 7298 2438145 5 Extended /dev/sda5 6994 7298 2438144 82 Linux swap / Solaris

  Read the article

• Accessing second hard drive

  - by Jonathan

  So I recently installed Ubuntu 10.10 64-bit on my computer. I installed it on my 60gb SSD hard drive, and in the installation it never acknowledged the existence of my second hard drive. The hard drive that I keep all my files on, and which I want to make my home folder if I can, is a Western Digital Caviar Black 1TB SATA 6Gb/s 64MB cache (WD1002FAEX). I've read the following: https://help.ubuntu.com/community/Mount but honestly cannot work out how to access the hard drive from my Ubuntu installation. I did have Windows 7 64-bit prior to installing Ubuntu. I have backed up all the files on the hard drive, but if I could just access them straight off that would be super cool. Does anyone know how I can use the second hard drive? Thank you for your help EDIT: The following directories are currently in my /dev/ folder: ati/, block/, bsg/, bus/, char/, cpu/, isk/, input/, mapper/, net/, pktcdvd/, pts/, shm/, snd/, and usb/ EDIT: Result from sudo fdisk -l Disk /dev/sda: 60.0 GB, 60022480896 bytes 255 heads, 63 sectors/track, 7297 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000d2dfd Device Boot Start End Blocks Id System /dev/sda1 * 1 6994 56174592 83 Linux /dev/sda2 6994 7298 2438145 5 Extended /dev/sda5 6994 7298 2438144 82 Linux swap / Solaris @djeykib So very close to fixing it.. unfortunately on the last command you gave it says this: $ sudo apt-get install linux-lts-backport-natty Reading package lists... Done Building dependency tree Reading state information... Done E: Unable to locate package linux-lts-backport-natty Checking on http://www.ubuntuupdates.org/ppas reveals that it is only available for 10.04. Looks like I'll have to unplug and re-plug hardware if I want it working still :(

  Read the article

• How to make Windows 7 machine allocate a lot of hard disk cache?

  - by Jian Lin

  I am recording some game play capture (recording playing of PS3 or Wii) using a PC with Windows 7 and Hauppauge 1212 HD Recorder, and I have 4GB of RAM... is there a way to increase the size of Windows 7's hard disk cache size so that writing to the hard drive can be super fast? Since there is at least 1.5GB of RAM not being used, something like allocating 1GB just as hard disk cache, is it possible?

  Read the article

• WD external hard drive not detected

  - by Khang Nguyen

  I am a beginner in Ubuntu. And I have just installed Ubuntu 11.10 in my Dell laptop. When I plugged my WD external hard drive in, it read the first time, but since I have a unlock.exe file (password for the hard drive). So I installed Wine to read it. But it gives me an error. I restart the machine, and plugged the hard drive in again. And it is not recognized anymore. Can anybody help me, please? Thank you!

  Read the article

• Retro Ad – 10 MB Hard-Drive for $3398 [Image]

  - by Asian Angel

  This is definitely one hard-drive (and price) that you will not be feeling nostalgic over! View the Full-Size Version of the Ad (Image) The Hard Disk you’ve been waiting for. [via Fail Desk] Why Enabling “Do Not Track” Doesn’t Stop You From Being Tracked HTG Explains: What is the Windows Page File and Should You Disable It? How To Get a Better Wireless Signal and Reduce Wireless Network Interference

  Read the article

• System locking up with suspicious messages about hard disk

  - by Chris Conway

  My system has started behaving strangely, intermittently locking up. I see messages like the following in syslog: Nov 18 22:22:00 claypool kernel: [ 3428.078156] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0 Nov 18 22:22:00 claypool kernel: [ 3428.078163] ata3.00: irq_stat 0x40000000 Nov 18 22:22:00 claypool kernel: [ 3428.078167] sr 2:0:0:0: CDB: Test Unit Ready: 00 00 00 00 00 00 Nov 18 22:22:00 claypool kernel: [ 3428.078182] ata3.00: cmd a0/00:00:00:00:00/00:00:00:00:00/a0 tag 0 Nov 18 22:22:00 claypool kernel: [ 3428.078184] res 50/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x1 (device error) Nov 18 22:22:00 claypool kernel: [ 3428.078188] ata3.00: status: { DRDY } Nov 18 22:22:00 claypool kernel: [ 3428.080887] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0 Nov 18 22:22:00 claypool kernel: [ 3428.080890] ata3.00: irq_stat 0x40000000 Nov 18 22:22:00 claypool kernel: [ 3428.080893] sr 2:0:0:0: CDB: Test Unit Ready: 00 00 00 00 00 00 Nov 18 22:22:00 claypool kernel: [ 3428.080905] ata3.00: cmd a0/00:00:00:00:00/00:00:00:00:00/a0 tag 0 Nov 18 22:22:00 claypool kernel: [ 3428.080906] res 50/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x1 (device error) Nov 18 22:22:00 claypool kernel: [ 3428.080910] ata3.00: status: { DRDY } And then this: Nov 18 23:13:56 claypool kernel: [ 6544.000798] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen Nov 18 23:13:56 claypool kernel: [ 6544.000804] ata1.00: failed command: FLUSH CACHE EXT Nov 18 23:13:56 claypool kernel: [ 6544.000814] ata1.00: cmd ea/00:00:00:00:00/00:00:00:00:00/a0 tag 0 Nov 18 23:13:56 claypool kernel: [ 6544.000815] res 40/00:00:00:4f:c2/00:00:00:00:00/40 Emask 0x4 (timeout) Nov 18 23:13:56 claypool kernel: [ 6544.000819] ata1.00: status: { DRDY } Nov 18 23:13:56 claypool kernel: [ 6544.000825] ata1: hard resetting link Nov 18 23:14:01 claypool kernel: [ 6549.360324] ata1: link is slow to respond, please be patient (ready=0) Nov 18 23:14:06 claypool kernel: [ 6554.008091] ata1: COMRESET failed (errno=-16) Nov 18 23:14:06 claypool kernel: [ 6554.008103] ata1: hard resetting link Nov 18 23:14:11 claypool kernel: [ 6559.372246] ata1: link is slow to respond, please be patient (ready=0) Nov 18 23:14:16 claypool kernel: [ 6564.020228] ata1: COMRESET failed (errno=-16) Nov 18 23:14:16 claypool kernel: [ 6564.020235] ata1: hard resetting link Nov 18 23:14:21 claypool kernel: [ 6569.380109] ata1: link is slow to respond, please be patient (ready=0) Nov 18 23:14:31 claypool kernel: [ 6579.460243] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Nov 18 23:14:31 claypool kernel: [ 6579.486595] ata1.00: configured for UDMA/133 Nov 18 23:14:31 claypool kernel: [ 6579.486601] ata1.00: retrying FLUSH 0xea Emask 0x4 Nov 18 23:14:31 claypool kernel: [ 6579.486939] ata1.00: device reported invalid CHS sector 0 Nov 18 23:14:31 claypool kernel: [ 6579.486952] ata1: EH complete Nov 18 23:17:01 claypool CRON[3910]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Nov 18 23:17:01 claypool CRON[3908]: (CRON) error (grandchild #3910 failed with exit status 1) Nov 18 23:17:01 claypool postfix/sendmail[3925]: fatal: open /etc/postfix/main.cf: No such file or directory Nov 18 23:17:01 claypool CRON[3908]: (root) MAIL (mailed 1 byte of output; but got status 0x004b, #012) Nov 18 23:39:01 claypool CRON[4200]: (root) CMD ( [ -x /usr/lib/php5/maxlifetime ] && [ -d /var/lib/php5 ] && find /var/lib/php5/ -type f -cmin +$(/usr/lib/php5/maxlifetime) -print0 | xargs -n 200 -r -0 rm) There are no messages marked after 23:39. When I next tried to use the machine, it would not return from the screensaver (blank screen), nor switch to another terminal, and I had to hard reboot it. [UPDATE] The output of smartctl is here. I had trouble getting this, because / is being mounted read-only (?!), which prevents most applications from running. Also, it may not be related, but I have the following worrying messages in dmesg: [ 10.084596] k8temp 0000:00:18.3: Temperature readouts might be wrong - check erratum #141 [ 10.098477] i2c i2c-0: nForce2 SMBus adapter at 0x600 [ 10.098483] ACPI: resource nForce2_smbus [io 0x0700-0x073f] conflicts with ACPI region SM00 [??? 0x00000700-0x0000073f flags 0x30] [ 10.098486] ACPI: This conflict may cause random problems and system instability [ 10.098487] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver [ 10.098509] i2c i2c-1: nForce2 SMBus adapter at 0x700 [ 10.112570] Linux agpgart interface v0.103 [ 10.155329] atk: Resources not safely usable due to acpi_enforce_resources kernel parameter [ 10.161506] it87: Found IT8712F chip at 0x290, revision 8 [ 10.161517] it87: VID is disabled (pins used for GPIO) [ 10.161527] it87: in3 is VCC (+5V) [ 10.161528] it87: in7 is VCCH (+5V Stand-By) [ 10.161560] ACPI: resource it87 [io 0x0295-0x0296] conflicts with ACPI region ECRE [??? 0x00000290-0x000002af flags 0x45] [ 10.161562] ACPI: This conflict may cause random problems and system instability [ 10.161564] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver [UPDATE 2] I swapped in a new SATA cable, per Phil's suggestion. The current output of smartctl is here, if it helps. [UPDATE 3] I don't think the cable fixed it. The system hasn't locked up yet, but my media player crashed a few minutes ago and I have the following in the syslog: Nov 20 16:07:17 claypool kernel: [ 2294.400033] ata1: link is slow to respond, please be patient (ready=0) Nov 20 16:07:47 claypool kernel: [ 2324.084581] ata1: COMRESET failed (errno=-16) Nov 20 16:07:47 claypool kernel: [ 2324.084588] ata1: limiting SATA link speed to 1.5 Gbps Nov 20 16:07:47 claypool kernel: [ 2324.084592] ata1: hard resetting link I get the following response from smartctl: $ sudo smartctl -a /dev/sda [sudo] password for chris: sudo: Can't open /var/lib/sudo/chris/0: Read-only file system smartctl 5.40 2010-03-16 r3077 [i686-pc-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net Device: /0:0:0:0 Version: scsiModePageOffset: response length too short, resp_len=47 offset=50 bd_len=46 >> Terminate command early due to bad response to IEC mode page A mandatory SMART command failed: exiting. To continue, add one or more '-T permissive' options.

  Read the article

• how to i lock a Harddrive to a certain drive letter

  - by Memor-X

  i have an external hard drive that i have set to Drive F which on it contains some programs that i have shortcuts on the desktop how i have a second external hard drive which i store my music on which is auto assigned to Drive E, due to someone thinking that Australians love to have f** wings on power plugs for hard drives while power boards have each socket close together i can have both of these hard drives set at the same time my music hard drive i normally only plug up when i sync music to my ipod but on occasion when i unplug my music hard drive and plug my old one back in or at times when i turn on my computer with the music hard drive in, turn off my computer and turn it back on with my old hard drive it's drive letter gets switched to E i get annoyed having to always go into disk management and change the drive letter back to F when this happens so i am wondering if I can lock my hard drive to always be F, if anything else tries to be F it can fail for all i care If there is a batch file i can use that'll go though all the steps of Disk Management to change a drive's letter, that way i can set it up in the startup folder

  Read the article

• Does a Samsung G3 Station external hard drive stop working when power supply is too high?

  - by Cacovsky

  I have a Samsung G3 Station 2TB external hard drive (link to PDF specs here). It was working perfectly when I accidentally plugged it in my notebook's power source. The notebook's power source is 19V/3.42A. The hard drive's is 12V/2A and I know that, inside its case, there is regular 2TB SATA drive, along with some sort of adapter. Does this adapter has some kind of power protection? I opened the case and the hard drive board smells bad. Does my data is forever lost or can I replace its board?

  Read the article

• Unable to mount external hard drive - Damaged file system and MFT

  - by Khalifa Abbas Lame

  I get the following error when i try to mount my external hard drive. UNABLE TO MOUNT Error mounting /dev/sdc1 at /media/khalibloo/Khalibloo2: Command-line `mount -t "ntfs" -o "uhelper=udisks2,nodev,nosuid,uid=1000,gid=1000,dmask=0077,fmask=0177" "/dev/sdc1" "/media/khalibloo/Khalibloo2"' exited with non-zero exit status 13: ntfs_attr_pread_i: ntfs_pread failed: Input/output error Failed to read of MFT, mft=6 count=1 br=-1: Input/output error Failed to open inode FILE_Bitmap: Input/output error Failed to mount '/dev/sdc1': Input/output error NTFS is either inconsistent, or there is a hardware fault, or it's a SoftRAID/FakeRAID hardware. In the first case run chkdsk /f on Windows then reboot into Windows twice. The usage of the /f parameter is very important! If the device is a SoftRAID/FakeRAID then first activate it and mount a different device under the /dev/mapper/ directory, (e.g. /dev/mapper/nvidia_eahaabcc1). Please see the 'dmraid' documentation for more details. It doesn't mount on windows either: "I/O Device error" it's an ntfs hard drive with a single partition Of course, i tried chkdsk /f. it reported several file segments as unreadable, but didn't say whether it fixed them or not (apparently not). also tried with the /b flag. ntfsfix reported the volume as corrupt. TestDisk was able to fix a small error with the partition table by adding the "80" flag for the active (only) partition. TestDisk also confirmed that the boot sector was fine and it matched the backup. However, when attempting to repair the MFT, it couldn't read the MFT. It also couldn't list the files on the hard drive. It says file system may be damaged. Active@ also shows that MFT is missing or corrupt. So how do i fix the file system? or the MFT?

  Read the article

• Hard drive clicking noise on Acer AO722

  - by Blank

  I'm running Ubuntu 11.10 on an Acer Aspire One 722. Whenever I'm on battery power I get a clicking sound from my hard drive every 5 seconds or so (this does not happen when the laptop is plugged in). I'm dual booting with Windows 7 and I don't get the clicking sound in Windows. The clicking sound stops when I run the command:sudo hdparm -B 254 /dev/sda Also, according to:sudo smartctl -H /dev/sda my hard drive is healthy. Is this clicking sound something I can just ignore? Or is it a serious problem and will it eventually damage my computer? If so, how would I fix it? I have tried adding hdparm -B 254 /dev/sda to my /etc/rc.local file, but I still run into the clicking problem if my computer boots while plugged in and is then unplugged. Also, I'm finding this fix to be unreliable. Sometimes it works, sometimes it does not. Is this a good solution and is there a better way of doing this? Also, would running my laptop with a -B value of 254 have any negative effects? (I read somewhere about a lower level protecting the hard drive from bumps)

  Read the article

• Easiest way to replace preinstalled Windows 8 with new hard drive with Windows 7

  - by Andrew

  There are all kinds of questions and answers relevant moving Windows 8 to a new hard drive. I'm not seeing anything quite applicable to my situation. I have a new, unopened, unbooted notebook with pre-installed Windows 8. I will be replacing the hard drive before ever booting, unless that is not possible for some reason. I want to "downgrade" to Windows 7 Pro, and I want a clean installation. To do so legitimately, I apparently either need to: Upgrade Windows 8 to Windows 8 Pro using Windows 8 Pro Pack, then downgrade; or Just install a newly-licensed copy of Windows 7 Pro. (Let me know if I've missed an option.) Installation media is likely not a problem, though if I need something vendor-specific that I cannot otherwise download, that could present an issue (Asus notebook, if that matters). If I could, I would just buy the Pro Pack upgrade, swap the hard drive (without ever booting), then install Windows 7 Pro directly on the new hard drive, using the Pro Pack key for activation. Will this work? Are there any activation issues? Edited to clarify, as some comments and answers indicate confusion: Here is, ideally, what I want to do: Before ever powering on the notebook, remove the current hard drive. Replace this hard drive with a new, blank hard drive. Install a clean copy of Windows 7 Pro on this new, blank hard drive. Unless I have no choice to accomplish the end result (a clean install of Win7 Pro on the newly-installed, previously-blank hard drive), I am not wanting to: Install Windows 7 "over" the current Windows 8 install (after upgrading to Win8 Pro). That would involve using the currenly-installed hard drive. I want to use a new, different hard drive. Copy the Win8 install to the new hard drive, then install Windows 7 "over" that installation. Install Windows 7 "over" the current Windows 8 install (after upgrading to Win8 Pro), then copy the installation to the new hard drive. If I have to use one of those three options, I will, but only if there is no other choice. Please note that this question is not about licensing: I will purchase the necessary license(s) to accomplish this procedure legally (apparently either Win8 Pro Pack or Win7 Pro -- the former currently appears less expensive).

  Read the article

• PSU died, is hard drive fried? Are other components damaged?

  - by srand

  After discovering and replacing my dead PSU, I was able to boot back into Windows. Everything seems to be working fine, however, one hard drive is not. Windows 7 says that this SATA hard drive needs to be formatted before it can work. Can the data be recovered? Also, is there a way to check the integrity of the other components of my computer or assume they will work fine?

  Read the article

• Are laptop hard drives fairly generic, or do I need to be careful to get the right one for my comput

  - by ngm

  I have a Dell Inspiron 1525 laptop, and the hard drive is failing and I'd like to get a new one. What I'm wondering is, do I need to buy a hard drive specific to my computer model, or are laptop harddrives usually fairly generic? (If that's the case then I can shop around for the best value.)

  Read the article

• Access secondary hard disk from Virtual Machine

  - by Frank V

  I have a fairly specific question. I had Ubuntu on my Laptop (for years). For a variety of reasons, I've had to switch to Windows but the computer has two hard drives. The main drive was reformatted and I've installed windows. The second hard drive still has the Linux system disk format (not sure on type). Obviously, windows can't access it but can I access it from a Virtual machine (VirtualBox) or will I need to load up a Live-Session to access / move the contents? Edit: If this is possible, how would one proceed to mount the disk?

  Read the article

• How a Hard Drive Works in Slow Motion [Video]

  - by Asian Angel

  This short video lets you have a good luck at a hard drive in slow motion as the actuator arm moves across the disk and then water is added to the equation as well… How a Hard Drive works in Slow Motion – The Slow Mo Guys [via BoingBoing] HTG Explains: What Is Two-Factor Authentication and Should I Be Using It? HTG Explains: What Is Windows RT and What Does It Mean To Me? HTG Explains: How Windows 8′s Secure Boot Feature Works & What It Means for Linux

  Read the article

• Which hard disk drive is which?

  - by djeikyb

  I want to know which hard disk drive corresponds to which device path. It's trivial to match the hard disk stats (brand, size) with the dev path, but I want more. I want to know which drive is which inside my case. What's a good way to go about getting this info? I would prefer not to tear apart my server to remove all the drives, then add back one by one. I am willing to preform reboots. The drives are inconveniently scrunched together in the case. The label information is hidden. I can open the case. Most disks are SATA, so theoretically hot swappable. So, Unplugging and tracing cables might help in answering.

  Read the article

• Slow transfer to external USB3 hard drive

  - by JMP

  Trying to backup data from hard drive before reloading windows following some issue with its load. Having trouble with the file transfer to a USB3/2 external hard drive NTFS. Getting transfer speed of about 116.7kB/sec. In other words its taking about 5 hours to transfer 1.4GB. I've got about 80GB to go. So the transfer is going to take 11days. Seems a little on the slow side. Am I missing something? Is there a way to make this faster. No issue with the external drive transferring this amount in windows. But don't have that option at the moment.

  Read the article

• Save to Hard Drive instead of bootable USB

  - by WAM

  I followed the instructions on the Ubuntu website on how to put Ubuntu 12.04 on a USB and make it a bootable USB stick for windows. It worked fine and I can boot up and run Ubuntu, but every time I try to download software or change settings it tries to save it to the USB rather than the hard drive built into the computer. The USB doesn't have enough space so the download fails and in addition it doesn't retain setting changes so when I restart my computer all the settings return to default and anything I saved is gone. Is there any way to change things so that when I download software or change settings Ubuntu will save it to my hard drive instead of the USB?

  Read the article

• Install failing new hard drives

  - by John

  I'm trying to install Ubuntu server 12.04 on my new hard drives but it seems to fail. Once past the option menu where is asked the partition to install the OS on, goes into a hold and no progress is shown afterwards. The hard disk I'm trying to install it on is: Western Digital WD20EARX The installation process hangs around 'installing core packages/installing the base system' . The CD comes through the test with being valid/ok. any help would be appreciated. Thanks in advance.

  Read the article

• External hard-drive is "clicking" when idle [closed]

  - by mirumir

  I'm struggling with a very annoying issue: My new hard-drive (Samsung Spinpoint M8 1TB (HN-M101MBB) was build in an USB 3.0 external case (Lian Li EX-10QR) and formatted with ext4. When this hard-drive is connected to my Notebook via USB 2.0 it "klicks", the LED flashs too, every second, but only when it's idle! It stays silent, when something is copying or reading from it. But when this drive was formatted with ext3 or fat, it always remained silent. This also happens with a Western Digital WD10JPVT Scorpio Blue, but the "klicks" are even louder! System: 12.04 64-bit with Gnome-Shell. Any ideas how to approach this issue?

  Read the article

• Slow tranfer to external USB3 hard drive

  - by JMP

  Trying to backup data from hard drive before reloading windows following some issue with its load. Having trouble with the file transfer to a USB3/2 external hard drive NTFS. Getting transfer speed of about 116.7kB/sec. In other words its taking about 5 hours to tranfer 1.4GB. I've got about 80GB to go. So the transfer is going to take 11days. Seems a little on the slow side. Am I missing something? Is there a way to make this faster. No issue with the external drive tranferring this amount in windows. But don't have that option at the moment.

  Read the article

• Partition Hard Drive For Data

  - by user211779

  Greetings ~ I am a new Linux/Ubuntu user. For various reasons (mostly my own ignorance) I am on my third install of Ubuntu 12.04. I want to partition the hard drive to create a drive for data and personal files in case I ever have to install again. I have been struggling all afternoon to make a gparted live USB. Tuxboot looked like the answer but I get an error message when using it. So, I am asking for help. Ultimately, I want to partition the hard drive for data and personal files. What do you recommend?

  Read the article

• Maxtor 500GB external hard drive not being detected but power is going to it?

  - by ClarkeyBoy

  I have 2 * Maxtor Onetouch 4 Lite 500GB external hard drives (part no. 9NT2A4-500). They both used to work fine on my old laptop (an Acer) but I have not used them for about a year, since my laptop was stolen and I got this one (also an Acer [Aspire 7738G]). I have one plugged into the mains with one of the leads I believe was supplied with them. It appears to be receiving power as it is warm and the power light (on the unit itself) is on; also the mains adapter is fairly warm. I also have it plugged into my laptop with a USB lead which I have tested on my mp3 player (so I know it works). However my hard drive is not showing on my computer. I have tried checking for new hardware, installing the software that was supplied with it, checking drive letters in case it is registered as C: or something stupid, checking for problems etc... I can't find any cause for it to do this. It does appear to be starting up and, possibly, shutting down and restarting constantly (that's what it sounds like altho I can't be certain). I have had both hard drives stored in different places for the last year and they're both doing the same thing.. if it was only one then I'd guess it had got damaged or corrupted or something but since it is both I doubt this is it. The only things in common with both of them are the leads and the laptop, however I know the USB lead works and guess the mains lead works as there is power going to the unit. Has anyone come across this before or does anyone have any idea what the cause / solution to the problem is? Any help would be greatly appreciated. Regards, Richard

  Read the article

• Move virtual machine hard disk to a separate physical hard disk for better performance?

  - by joeeoj

  I have a dual-core machine with the host OS and many guest virtual OSs. Although I have 8GB of RAM, I notice a slowdown when I turn some virtual machine on (and it takes only 1GB RAM). I was told that I should move virtual machine hard disk file to a separate (another) physical hard drive in my PC to get better performance. This way the head of the hard disk would not have to jump from the virtual OS to the host OS as each hard drive would have its own head to deal with the OS: hard drive 1 head for host OS and hard drive 2 head for guest OS. Is this true? Should I get another hard disk only for virtual machine hard disk files?

  Read the article

• VirtualBox : increase hard disk size of the virtual machine

  - by wim

  I have run out of space on my WinXP virtual machine, which I only gave 10 GB space for when I created it. Is there an easy way to increase it to, say, 20 GB? I can't see any obvious option in VirtualBox settings. edit: the suggestion below gives this error wim@wim-ubuntu:/media/data/winxp_vm$ VBoxManage modifyhd wim.vdi --resize 20000 VBoxManage: error: Cannot register the hard disk '/media/data/winxp_vm/wim.vdi' {46284957-2c09-4e70-8a49-bfbe0f7f681d} because a hard disk '/home/wim/VirtualBox VMs/winxp_vm/wim.vdi' with UUID {46284957-2c09-4e70-8a49-bfbe0f7f681d} already exists VBoxManage: error: Details: code NS_ERROR_INVALID_ARG (0x80070057), component VirtualBox, interface IVirtualBox, callee nsISupports Context: "OpenMedium(Bstr(pszFilenameOrUuid).raw(), enmDevType, AccessMode_ReadWrite, fForceNewUuidOnOpen, pMedium.asOutParam())" at line 210 of file VBoxManageDisk.cpp edit2: removing the .vdi from VirtualBox before calling VBoxManage command, then adding it back in, was successful. But now I can't boot the virtual machine, I get this worrying screen: By the way, it says FATAL: Could not read from the boot medium! System halted. edit3: The vdi must be reattached to the VM after VBoxManage command. Further, the partition will need to be resized from WITHIN windows, because you will have this empty space: I was able to resize the partition easily using a bit of freeware called EASEUS Partition Master 9.1.0 Home Edition.

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >