Search Results

Search found 30 results on 2 pages for 'k3'.

Page 2/2 | < Previous Page | 1 2 

  • Problem with setup VPN in Ubuntu Server 12.04

    - by Yozone W.
    I have a problem with setup VPN server on my Ubuntu VPS, here is my server environments: Ubuntu Server 12.04 x86_64 xl2tpd 1.3.1+dfsg-1 pppd 2.4.5-5ubuntu1 openswan 1:2.6.38-1~precise1 After install software and configuration: ipsec verify Checking your system to see if IPsec got installed and started correctly: Version check and ipsec on-path [OK] Linux Openswan U2.6.38/K3.2.0-24-virtual (netkey) Checking for IPsec support in kernel [OK] SAref kernel support [N/A] NETKEY: Testing XFRM related proc values [OK] [OK] [OK] Checking that pluto is running [OK] Pluto listening for IKE on udp 500 [OK] Pluto listening for NAT-T on udp 4500 [OK] Checking for 'ip' command [OK] Checking /bin/sh is not /bin/dash [WARNING] Checking for 'iptables' command [OK] Opportunistic Encryption Support [DISABLED] /var/log/auth.log message: Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [RFC 3947] method set to=115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike] meth=114, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-08] meth=113, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-07] meth=112, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-06] meth=111, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-05] meth=110, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-04] meth=109, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-03] meth=108, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02] meth=107, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02_n] meth=106, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: ignoring Vendor ID payload [FRAGMENTATION 80000000] Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [Dead Peer Detection] Oct 16 06:50:54 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: responding to Main Mode from unknown peer [My IP Address] Oct 16 06:50:54 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: transition from state STATE_MAIN_R0 to state STATE_MAIN_R1 Oct 16 06:50:54 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: STATE_MAIN_R1: sent MR1, expecting MI2 Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: NAT-Traversal: Result using draft-ietf-ipsec-nat-t-ike (MacOS X): peer is NATed Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: transition from state STATE_MAIN_R1 to state STATE_MAIN_R2 Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: STATE_MAIN_R2: sent MR2, expecting MI3 Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: ignoring informational payload, type IPSEC_INITIAL_CONTACT msgid=00000000 Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: Main mode peer ID is ID_IPV4_ADDR: '192.168.12.52' Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: switched from "L2TP-PSK-NAT" to "L2TP-PSK-NAT" Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: deleting connection "L2TP-PSK-NAT" instance with peer [My IP Address] {isakmp=#0/ipsec=#0} Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: transition from state STATE_MAIN_R2 to state STATE_MAIN_R3 Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: new NAT mapping for #5, was [My IP Address]:2251, now [My IP Address]:2847 Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: STATE_MAIN_R3: sent MR3, ISAKMP SA established {auth=OAKLEY_PRESHARED_KEY cipher=aes_256 prf=oakley_sha group=modp1024} Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: Dead Peer Detection (RFC 3706): enabled Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: the peer proposed: [My Server IP Address]/32:17/1701 -> 192.168.12.52/32:17/0 Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: NAT-Traversal: received 2 NAT-OA. using first, ignoring others Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: responding to Quick Mode proposal {msgid:8579b1fb} Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: us: [My Server IP Address]<[My Server IP Address]>:17/1701 Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: them: [My IP Address][192.168.12.52]:17/65280===192.168.12.52/32 Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: transition from state STATE_QUICK_R0 to state STATE_QUICK_R1 Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: STATE_QUICK_R1: sent QR1, inbound IPsec SA installed, expecting QI2 Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: Dead Peer Detection (RFC 3706): enabled Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: transition from state STATE_QUICK_R1 to state STATE_QUICK_R2 Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: STATE_QUICK_R2: IPsec SA established transport mode {ESP=>0x08bda158 <0x4920a374 xfrm=AES_256-HMAC_SHA1 NATOA=192.168.12.52 NATD=[My IP Address]:2847 DPD=enabled} Oct 16 06:51:16 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: received Delete SA(0x08bda158) payload: deleting IPSEC State #6 Oct 16 06:51:16 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: ERROR: netlink XFRM_MSG_DELPOLICY response for flow eroute_connection delete included errno 2: No such file or directory Oct 16 06:51:16 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: received and ignored informational message Oct 16 06:51:16 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: received Delete SA payload: deleting ISAKMP State #5 Oct 16 06:51:16 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address]: deleting connection "L2TP-PSK-NAT" instance with peer [My IP Address] {isakmp=#0/ipsec=#0} Oct 16 06:51:16 vpn pluto[3963]: packet from [My IP Address]:2847: received and ignored informational message xl2tpd -D message: xl2tpd[4289]: Enabling IPsec SAref processing for L2TP transport mode SAs xl2tpd[4289]: IPsec SAref does not work with L2TP kernel mode yet, enabling forceuserspace=yes xl2tpd[4289]: setsockopt recvref[30]: Protocol not available xl2tpd[4289]: This binary does not support kernel L2TP. xl2tpd[4289]: xl2tpd version xl2tpd-1.3.1 started on vpn.netools.me PID:4289 xl2tpd[4289]: Written by Mark Spencer, Copyright (C) 1998, Adtran, Inc. xl2tpd[4289]: Forked by Scott Balmos and David Stipp, (C) 2001 xl2tpd[4289]: Inherited by Jeff McAdams, (C) 2002 xl2tpd[4289]: Forked again by Xelerance (www.xelerance.com) (C) 2006 xl2tpd[4289]: Listening on IP address [My Server IP Address], port 1701 Then it just stopped here, and have no any response. I can't connect VPN on my mac client, the /var/log/system.log message: Oct 16 15:17:36 azone-iMac.local configd[17]: SCNC: start, triggered by SystemUIServer, type L2TP, status 0 Oct 16 15:17:36 azone-iMac.local pppd[3799]: pppd 2.4.2 (Apple version 596.13) started by azone, uid 501 Oct 16 15:17:38 azone-iMac.local pppd[3799]: L2TP connecting to server 'vpn.netools.me' ([My Server IP Address])... Oct 16 15:17:38 azone-iMac.local pppd[3799]: IPSec connection started Oct 16 15:17:38 azone-iMac.local racoon[359]: Connecting. Oct 16 15:17:38 azone-iMac.local racoon[359]: IPSec Phase1 started (Initiated by me). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKE Packet: transmit success. (Initiator, Main-Mode message 1). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKE Packet: receive success. (Initiator, Main-Mode message 2). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKE Packet: transmit success. (Initiator, Main-Mode message 3). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKE Packet: receive success. (Initiator, Main-Mode message 4). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKE Packet: transmit success. (Initiator, Main-Mode message 5). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKEv1 Phase1 AUTH: success. (Initiator, Main-Mode Message 6). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKE Packet: receive success. (Initiator, Main-Mode message 6). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKEv1 Phase1 Initiator: success. (Initiator, Main-Mode). Oct 16 15:17:38 azone-iMac.local racoon[359]: IPSec Phase1 established (Initiated by me). Oct 16 15:17:39 azone-iMac.local racoon[359]: IPSec Phase2 started (Initiated by me). Oct 16 15:17:39 azone-iMac.local racoon[359]: IKE Packet: transmit success. (Initiator, Quick-Mode message 1). Oct 16 15:17:39 azone-iMac.local racoon[359]: IKE Packet: receive success. (Initiator, Quick-Mode message 2). Oct 16 15:17:39 azone-iMac.local racoon[359]: IKE Packet: transmit success. (Initiator, Quick-Mode message 3). Oct 16 15:17:39 azone-iMac.local racoon[359]: IKEv1 Phase2 Initiator: success. (Initiator, Quick-Mode). Oct 16 15:17:39 azone-iMac.local racoon[359]: IPSec Phase2 established (Initiated by me). Oct 16 15:17:39 azone-iMac.local pppd[3799]: IPSec connection established Oct 16 15:17:59 azone-iMac.local pppd[3799]: L2TP cannot connect to the server Oct 16 15:17:59 azone-iMac.local racoon[359]: IPSec disconnecting from server [My Server IP Address] Oct 16 15:17:59 azone-iMac.local racoon[359]: IKE Packet: transmit success. (Information message). Oct 16 15:17:59 azone-iMac.local racoon[359]: IKEv1 Information-Notice: transmit success. (Delete IPSEC-SA). Oct 16 15:17:59 azone-iMac.local racoon[359]: IKE Packet: transmit success. (Information message). Oct 16 15:17:59 azone-iMac.local racoon[359]: IKEv1 Information-Notice: transmit success. (Delete ISAKMP-SA). Anyone help? Thanks a million!

    Read the article

  • Problem with setup VPN on Ubuntu Server 12.04

    - by Yozone W.
    I have a problem with setup VPN server on my Ubuntu VPS, here is my server environments: Ubuntu Server 12.04 x86_64 xl2tpd 1.3.1+dfsg-1 pppd 2.4.5-5ubuntu1 openswan 1:2.6.38-1~precise1 After install software and configuration: ipsec verify Checking your system to see if IPsec got installed and started correctly: Version check and ipsec on-path [OK] Linux Openswan U2.6.38/K3.2.0-24-virtual (netkey) Checking for IPsec support in kernel [OK] SAref kernel support [N/A] NETKEY: Testing XFRM related proc values [OK] [OK] [OK] Checking that pluto is running [OK] Pluto listening for IKE on udp 500 [OK] Pluto listening for NAT-T on udp 4500 [OK] Checking for 'ip' command [OK] Checking /bin/sh is not /bin/dash [WARNING] Checking for 'iptables' command [OK] Opportunistic Encryption Support [DISABLED] /var/log/auth.log message: Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [RFC 3947] method set to=115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike] meth=114, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-08] meth=113, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-07] meth=112, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-06] meth=111, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-05] meth=110, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-04] meth=109, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-03] meth=108, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02] meth=107, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02_n] meth=106, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: ignoring Vendor ID payload [FRAGMENTATION 80000000] Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [Dead Peer Detection] Oct 16 06:50:54 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: responding to Main Mode from unknown peer [My IP Address] Oct 16 06:50:54 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: transition from state STATE_MAIN_R0 to state STATE_MAIN_R1 Oct 16 06:50:54 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: STATE_MAIN_R1: sent MR1, expecting MI2 Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: NAT-Traversal: Result using draft-ietf-ipsec-nat-t-ike (MacOS X): peer is NATed Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: transition from state STATE_MAIN_R1 to state STATE_MAIN_R2 Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: STATE_MAIN_R2: sent MR2, expecting MI3 Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: ignoring informational payload, type IPSEC_INITIAL_CONTACT msgid=00000000 Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: Main mode peer ID is ID_IPV4_ADDR: '192.168.12.52' Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: switched from "L2TP-PSK-NAT" to "L2TP-PSK-NAT" Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: deleting connection "L2TP-PSK-NAT" instance with peer [My IP Address] {isakmp=#0/ipsec=#0} Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: transition from state STATE_MAIN_R2 to state STATE_MAIN_R3 Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: new NAT mapping for #5, was [My IP Address]:2251, now [My IP Address]:2847 Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: STATE_MAIN_R3: sent MR3, ISAKMP SA established {auth=OAKLEY_PRESHARED_KEY cipher=aes_256 prf=oakley_sha group=modp1024} Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: Dead Peer Detection (RFC 3706): enabled Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: the peer proposed: [My Server IP Address]/32:17/1701 -> 192.168.12.52/32:17/0 Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: NAT-Traversal: received 2 NAT-OA. using first, ignoring others Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: responding to Quick Mode proposal {msgid:8579b1fb} Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: us: [My Server IP Address]<[My Server IP Address]>:17/1701 Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: them: [My IP Address][192.168.12.52]:17/65280===192.168.12.52/32 Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: transition from state STATE_QUICK_R0 to state STATE_QUICK_R1 Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: STATE_QUICK_R1: sent QR1, inbound IPsec SA installed, expecting QI2 Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: Dead Peer Detection (RFC 3706): enabled Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: transition from state STATE_QUICK_R1 to state STATE_QUICK_R2 Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: STATE_QUICK_R2: IPsec SA established transport mode {ESP=>0x08bda158 <0x4920a374 xfrm=AES_256-HMAC_SHA1 NATOA=192.168.12.52 NATD=[My IP Address]:2847 DPD=enabled} Oct 16 06:51:16 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: received Delete SA(0x08bda158) payload: deleting IPSEC State #6 Oct 16 06:51:16 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: ERROR: netlink XFRM_MSG_DELPOLICY response for flow eroute_connection delete included errno 2: No such file or directory Oct 16 06:51:16 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: received and ignored informational message Oct 16 06:51:16 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: received Delete SA payload: deleting ISAKMP State #5 Oct 16 06:51:16 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address]: deleting connection "L2TP-PSK-NAT" instance with peer [My IP Address] {isakmp=#0/ipsec=#0} Oct 16 06:51:16 vpn pluto[3963]: packet from [My IP Address]:2847: received and ignored informational message xl2tpd -D message: xl2tpd[4289]: Enabling IPsec SAref processing for L2TP transport mode SAs xl2tpd[4289]: IPsec SAref does not work with L2TP kernel mode yet, enabling forceuserspace=yes xl2tpd[4289]: setsockopt recvref[30]: Protocol not available xl2tpd[4289]: This binary does not support kernel L2TP. xl2tpd[4289]: xl2tpd version xl2tpd-1.3.1 started on vpn.netools.me PID:4289 xl2tpd[4289]: Written by Mark Spencer, Copyright (C) 1998, Adtran, Inc. xl2tpd[4289]: Forked by Scott Balmos and David Stipp, (C) 2001 xl2tpd[4289]: Inherited by Jeff McAdams, (C) 2002 xl2tpd[4289]: Forked again by Xelerance (www.xelerance.com) (C) 2006 xl2tpd[4289]: Listening on IP address [My Server IP Address], port 1701 Then it just stopped here, and have no any response. I can't connect VPN on my mac client, the /var/log/system.log message: Oct 16 15:17:36 azone-iMac.local configd[17]: SCNC: start, triggered by SystemUIServer, type L2TP, status 0 Oct 16 15:17:36 azone-iMac.local pppd[3799]: pppd 2.4.2 (Apple version 596.13) started by azone, uid 501 Oct 16 15:17:38 azone-iMac.local pppd[3799]: L2TP connecting to server 'vpn.netools.me' ([My Server IP Address])... Oct 16 15:17:38 azone-iMac.local pppd[3799]: IPSec connection started Oct 16 15:17:38 azone-iMac.local racoon[359]: Connecting. Oct 16 15:17:38 azone-iMac.local racoon[359]: IPSec Phase1 started (Initiated by me). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKE Packet: transmit success. (Initiator, Main-Mode message 1). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKE Packet: receive success. (Initiator, Main-Mode message 2). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKE Packet: transmit success. (Initiator, Main-Mode message 3). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKE Packet: receive success. (Initiator, Main-Mode message 4). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKE Packet: transmit success. (Initiator, Main-Mode message 5). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKEv1 Phase1 AUTH: success. (Initiator, Main-Mode Message 6). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKE Packet: receive success. (Initiator, Main-Mode message 6). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKEv1 Phase1 Initiator: success. (Initiator, Main-Mode). Oct 16 15:17:38 azone-iMac.local racoon[359]: IPSec Phase1 established (Initiated by me). Oct 16 15:17:39 azone-iMac.local racoon[359]: IPSec Phase2 started (Initiated by me). Oct 16 15:17:39 azone-iMac.local racoon[359]: IKE Packet: transmit success. (Initiator, Quick-Mode message 1). Oct 16 15:17:39 azone-iMac.local racoon[359]: IKE Packet: receive success. (Initiator, Quick-Mode message 2). Oct 16 15:17:39 azone-iMac.local racoon[359]: IKE Packet: transmit success. (Initiator, Quick-Mode message 3). Oct 16 15:17:39 azone-iMac.local racoon[359]: IKEv1 Phase2 Initiator: success. (Initiator, Quick-Mode). Oct 16 15:17:39 azone-iMac.local racoon[359]: IPSec Phase2 established (Initiated by me). Oct 16 15:17:39 azone-iMac.local pppd[3799]: IPSec connection established Oct 16 15:17:59 azone-iMac.local pppd[3799]: L2TP cannot connect to the server Oct 16 15:17:59 azone-iMac.local racoon[359]: IPSec disconnecting from server [My Server IP Address] Oct 16 15:17:59 azone-iMac.local racoon[359]: IKE Packet: transmit success. (Information message). Oct 16 15:17:59 azone-iMac.local racoon[359]: IKEv1 Information-Notice: transmit success. (Delete IPSEC-SA). Oct 16 15:17:59 azone-iMac.local racoon[359]: IKE Packet: transmit success. (Information message). Oct 16 15:17:59 azone-iMac.local racoon[359]: IKEv1 Information-Notice: transmit success. (Delete ISAKMP-SA). Anyone help? Thanks a million!

    Read the article

  • l2tp / ipsec debian Openswan U2.6.38 does not connect

    - by locojay
    i am trying to get ipsec/l2tp running on a debian server with an iphone as a client but always get: Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [RFC 3947] method set to=115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike] meth=114, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-08] meth=113, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-07] meth=112, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-06] meth=111, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-05] meth=110, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-04] meth=109, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-03] meth=108, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02] meth=107, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02_n] meth=106, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: ignoring Vendor ID payload [FRAGMENTATION 80000000] Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [Dead Peer Detection] Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: responding to Main Mode from unknown peer <clientip> Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: transition from state STATE_MAIN_R0 to state STATE_MAIN_R1 Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: STATE_MAIN_R1: sent MR1, expecting MI2 Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: NAT-Traversal: Result using draft-ietf-ipsec-nat-t-ike (MacOS X): both are NATed Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: transition from state STATE_MAIN_R1 to state STATE_MAIN_R2 Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: STATE_MAIN_R2: sent MR2, expecting MI3 Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: ignoring informational payload, type IPSEC_INITIAL_CONTACT msgid=00000000 Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: Main mode peer ID is ID_IPV4_ADDR: '10.2.210.176' Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: switched from "L2TP-PSK-noNAT" to "L2TP-PSK-noNAT" Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: deleting connection "L2TP-PSK-noNAT" instance with peer <clientip> {isakmp=#0/ipsec=#0} Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: transition from state STATE_MAIN_R2 to state STATE_MAIN_R3 Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: new NAT mapping for #20, was <clientip>:43598, now <clientip>:49826 Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: STATE_MAIN_R3: sent MR3, ISAKMP SA established {auth=OAKLEY_PRESHARED_KEY cipher=aes_256 prf=oakley_sha group=modp1024} Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: Dead Peer Detection (RFC 3706): enabled Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: the peer proposed: <public ip>/32:17/1701 -> 10.2.210.176/32:17/0 Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: NAT-Traversal: received 2 NAT-OA. using first, ignoring others Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #21: responding to Quick Mode proposal {msgid:311d3282} Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #21: us: 171.138.2.13<171.138.2.13>:17/1701 Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #21: them: <clientip>[10.2.210.176]:17/61719 Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #21: transition from state STATE_QUICK_R0 to state STATE_QUICK_R1 Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #21: STATE_QUICK_R1: sent QR1, inbound IPsec SA installed, expecting QI2 Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #21: Dead Peer Detection (RFC 3706): enabled Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #21: transition from state STATE_QUICK_R1 to state STATE_QUICK_R2 Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #21: STATE_QUICK_R2: IPsec SA established transport mode {ESP=>0x05e23c9a <0x216077a9 xfrm=AES_256-HMAC_SHA1 NATOA=10.2.210.176 NATD=<clientip>:49826 DPD=enabled} Dec 2 21:00:26 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: received Delete SA(0x05e23c9a) payload: deleting IPSEC State #21 Dec 2 21:00:26 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: received and ignored informational message Dec 2 21:00:27 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: received Delete SA payload: deleting ISAKMP State #20 Dec 2 21:00:27 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip>: deleting connection "L2TP-PSK-noNAT" instance with peer <clientip> {isakmp=#0/ipsec=#0} Dec 2 21:00:27 vpn pluto[22711]: packet from <clientip>:49826: received and ignored informational message Dec 2 21:00:27 vpn pluto[22711]: ERROR: asynchronous network error report on eth0 (sport=4500) for message to <clientip> port 49826, complainant <clientip>: Connection refused [errno 111, origin ICMP type 3 code 3 (not authenticated)] my setup looks like this verizon fios actiontec -- DMZ-- ddwrt router -- debian xen instance actiontec : 192.168.1.1 ddwrt: 171.138.2.1 debian xen server: 171.138.2.13 forwarded udp 500, 4500, 1701 on ddwrt to debian xen instance. vpn passthrough is enabled /etc/ipsec.conf config setup dumpdir=/var/run/pluto/ nat_traversal=yes virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12,%v4:25.0.0.0/8,%v6:fd00::/8,%v6:fe80::/10,%v4:!171.138.2.0/24,%v4:!192.168.1.0/24 protostack=netkey # Add connections here conn L2TP-PSK-NAT rightsubnet=vhost:%priv also=L2TP-PSK-noNAT conn L2TP-PSK-noNAT authby=secret pfs=no auto=add keyingtries=3 # we cannot rekey for %any, let client rekey rekey=no # Apple iOS doesn't send delete notify so we need dead peer detection # to detect vanishing clients dpddelay=30 dpdtimeout=120 dpdaction=clear # Set ikelifetime and keylife to same defaults windows has ikelifetime=8h keylife=1h # l2tp-over-ipsec is transport mode type=transport # left=171.138.2.13 # # For updated Windows 2000/XP clients, # to support old clients as well, use leftprotoport=17/%any leftprotoport=17/1701 # # The remote user. # right=%any # Using the magic port of "%any" means "any one single port". This is # a work around required for Apple OSX clients that use a randomly # high port. rightprotoport=17/%any #force all to be nat'ed. because of ios conn passthrough-for-non-l2tp type=passthrough left=171.138.2.13 leftnexthop=171.138.2.1 right=0.0.0.0 rightsubnet=0.0.0.0/0 auto=route /etc/xl2tp/xl2tp.conf [global] ipsec saref = no listen-addr = 171.138.2.13 ;port = 1701 ;debug network = yes ;debug tunnel = yes ;debug network = yes ;debug packet = yes [lns default] ip range = 171.138.2.231-171.138.2.239 local ip = 171.138.2.13 assign ip = yes require chap = no refuse pap = no require authentication = no ;name = OpenswanVPN ppp debug = yes pppoptfile = /etc/ppp/options.xlt2tpd lenght bit = yes /etc/ppp/options.xl2tpd ;require-mschap-v2 pcp-accept-local ipcp-accept-local ipcp-accept-remote ;ms-dns 171.138.2.1 ms-dns 192.168.1.1 ms-dns 8.8.8.8 name l2tpd noccp auth crtscts idle 1800 mtu 1410 mru 1410 lock proxyarp connect-delay 5000 debug dump logfd 2 logfile /var/log/xl2tpd.log ipsec verify Checking your system to see if IPsec got installed and started correctly: Version check and ipsec on-path [OK] Linux Openswan U2.6.38/K3.0.0-1-amd64 (netkey) Checking for IPsec support in kernel [OK] SAref kernel support [N/A] NETKEY: Testing XFRM related proc values [OK] [OK] [OK] Checking that pluto is running [OK] Pluto listening for IKE on udp 500 [OK] Pluto listening for NAT-T on udp 4500 [OK] Two or more interfaces found, checking IP forwarding [FAILED] Checking NAT and MASQUERADEing [OK] Checking for 'ip' command [OK] Checking /bin/sh is not /bin/dash [WARNING] Checking for 'iptables' command [OK] Opportunistic Encryption Support [DISABLED] The failed can be ignored i guess since cat /proc/sys/net/ipv4/ip_forward returns 1 any help would be much appreciated as i don't have any idea why this is not working

    Read the article

  • OpenSwan IPsec connection drops after 30 seconds

    - by drcore
    I'm trying to connection from my Linux Mint 16 box to a CloudStack server. Building up the connection works (pings work across the tunnel). However 30 seconds later the IPsec tunnel gets terminated out of the blue. What could cause this consistent behaviour and how to fix it? The tunnel is setup using OpenSwan (U2.6.38/K(no kernel code presently loaded)) with the L2TP IPsec VPN manager from Werner Jaeger 1.0.9. The client is behind a NAT'ed router and the server is on public IP (CloudStack 4.2) Running ipsec verify complains about IPsec support in kernel. Not sure if this is a problem as the connection is being build up: Checking your system to see if IPsec got installed and started correctly: Version check and ipsec on-path [OK] Linux Openswan U2.6.38/K(no kernel code presently loaded) Checking for IPsec support in kernel [FAILED] SAref kernel support [N/A] Checking that pluto is running [FAILED] whack: Pluto is not running (no "/var/run/pluto/pluto.ctl") Checking for 'ip' command [OK] Checking /bin/sh is not /bin/dash [WARNING] Checking for 'iptables' command [OK] Opportunistic Encryption Support [DISABLED] Tunnel config: version 2.0 # conforms to second version of ipsec.conf specification config setup # plutodebug="parsing emitting control private" plutodebug=none strictcrlpolicy=no nat_traversal=yes interfaces=%defaultroute oe=off # which IPsec stack to use. netkey,klips,mast,auto or none protostack=netkey conn %default keyingtries=3 pfs=no rekey=yes type=transport left=%defaultroute leftprotoport=17/1701 rightprotoport=17/1701 conn Tunnel1 authby=secret right=37.48.75.97 rightid="" auto=add Log file of VPN connection build up: aug. 23 17:12:54.708 ipsec_setup: Starting Openswan IPsec U2.6.38/K3.11.0-12-generic... aug. 23 17:12:55.155 ipsec_setup: multiple ip addresses, using 192.168.178.32 on eth0 aug. 23 17:12:55.165 ipsec__plutorun: Starting Pluto subsystem... aug. 23 17:12:55.174 ipsec__plutorun: adjusting ipsec.d to /etc/ipsec.d aug. 23 17:12:55.177 recvref[30]: Protocol not available aug. 23 17:12:55.177 xl2tpd[14339]: This binary does not support kernel L2TP. aug. 23 17:12:55.178 Starting xl2tpd: xl2tpd. aug. 23 17:12:55.178 xl2tpd[14345]: xl2tpd version xl2tpd-1.3.1 started on desktopmint PID:14345 aug. 23 17:12:55.178 xl2tpd[14345]: Written by Mark Spencer, Copyright (C) 1998, Adtran, Inc. aug. 23 17:12:55.179 xl2tpd[14345]: Forked by Scott Balmos and David Stipp, (C) 2001 aug. 23 17:12:55.179 xl2tpd[14345]: Inherited by Jeff McAdams, (C) 2002 aug. 23 17:12:55.179 xl2tpd[14345]: Forked again by Xelerance (www.xelerance.com) (C) 2006 aug. 23 17:12:55.180 xl2tpd[14345]: Listening on IP address 0.0.0.0, port 1701 aug. 23 17:12:55.214 ipsec__plutorun: 002 added connection description "Tunnel1" aug. 23 17:13:15.532 104 "Tunnel1" #1: STATE_MAIN_I1: initiate aug. 23 17:13:15.532 003 "Tunnel1" #1: ignoring unknown Vendor ID payload [4f45755c645c6a795c5c6170] aug. 23 17:13:15.532 003 "Tunnel1" #1: received Vendor ID payload [Dead Peer Detection] aug. 23 17:13:15.533 003 "Tunnel1" #1: received Vendor ID payload [RFC 3947] method set to=115 aug. 23 17:13:15.533 106 "Tunnel1" #1: STATE_MAIN_I2: sent MI2, expecting MR2 aug. 23 17:13:15.534 003 "Tunnel1" #1: NAT-Traversal: Result using draft-ietf-ipsec-nat-t-ike (MacOS X): i am NATed aug. 23 17:13:15.534 108 "Tunnel1" #1: STATE_MAIN_I3: sent MI3, expecting MR3 aug. 23 17:13:15.534 010 "Tunnel1" #1: STATE_MAIN_I3: retransmission; will wait 20s for response aug. 23 17:13:15.545 003 "Tunnel1" #1: received Vendor ID payload [CAN-IKEv2] aug. 23 17:13:15.547 004 "Tunnel1" #1: STATE_MAIN_I4: ISAKMP SA established {auth=OAKLEY_PRESHARED_KEY cipher=aes_128 prf=oakley_sha group=modp2048} aug. 23 17:13:15.547 117 "Tunnel1" #2: STATE_QUICK_I1: initiate aug. 23 17:13:15.547 010 "Tunnel1" #2: STATE_QUICK_I1: retransmission; will wait 20s for response aug. 23 17:13:15.548 004 "Tunnel1" #2: STATE_QUICK_I2: sent QI2, IPsec SA established transport mode {ESP=>0x0ecef28b <0x3e1fbe3b xfrm=AES_128-HMAC_SHA1 NATOA=none NATD=none DPD=none} aug. 23 17:13:16.549 xl2tpd[14345]: Connecting to host <VPN gateway>, port 1701 aug. 23 17:13:18.576 xl2tpd[14345]: Connection established to <VPN gateway>, 1701. Local: 21163, Remote: 12074 (ref=0/0). aug. 23 17:13:18.576 xl2tpd[14345]: Calling on tunnel 21163 aug. 23 17:13:18.577 xl2tpd[14345]: check_control: Received out of order control packet on tunnel 12074 (got 0, expected 1) aug. 23 17:13:18.577 xl2tpd[14345]: handle_packet: bad control packet! aug. 23 17:13:18.577 xl2tpd[14345]: check_control: Received out of order control packet on tunnel 12074 (got 0, expected 1) aug. 23 17:13:18.577 xl2tpd[14345]: handle_packet: bad control packet! aug. 23 17:13:18.599 xl2tpd[14345]: Call established with <VPN gateway>, Local: 39035, Remote: 57266, Serial: 1 (ref=0/0) aug. 23 17:13:18.605 xl2tpd[14345]: start_pppd: I'm running: aug. 23 17:13:18.605 xl2tpd[14345]: "/usr/sbin/pppd" aug. 23 17:13:18.606 xl2tpd[14345]: "passive" aug. 23 17:13:18.606 xl2tpd[14345]: "nodetach" aug. 23 17:13:18.606 xl2tpd[14345]: ":" aug. 23 17:13:18.606 xl2tpd[14345]: "file" aug. 23 17:13:18.606 xl2tpd[14345]: "/etc/ppp/Tunnel1.options.xl2tpd" aug. 23 17:13:18.606 xl2tpd[14345]: "ipparam" aug. 23 17:13:18.607 xl2tpd[14345]: "<VPN gateway>" aug. 23 17:13:18.607 xl2tpd[14345]: "/dev/pts/4" aug. 23 17:13:18.607 pppd[14438]: Plugin passprompt.so loaded. aug. 23 17:13:18.607 pppd[14438]: pppd 2.4.5 started by root, uid 0 aug. 23 17:13:18.608 pppd[14438]: Using interface ppp0 aug. 23 17:13:18.608 pppd[14438]: Connect: ppp0 <--> /dev/pts/4 aug. 23 17:13:21.650 pppd[14438]: CHAP authentication succeeded: Access granted aug. 23 17:13:21.651 pppd[14438]: CHAP authentication succeeded aug. 23 17:13:21.692 pppd[14438]: local IP address 10.1.2.2 aug. 23 17:13:21.693 pppd[14438]: remote IP address 10.1.2.1 aug. 23 17:13:21.693 pppd[14438]: primary DNS address 10.1.2.1 aug. 23 17:13:21.694 pppd[14438]: secondary DNS address 10.1.2.1 aug. 23 17:13:46.528 Stopping xl2tpd: xl2tpd. aug. 23 17:13:46.528 xl2tpd[14345]: death_handler: Fatal signal 15 received aug. 23 17:13:46.529 pppd[14438]: Modem hangup aug. 23 17:13:46.529 pppd[14438]: Connect time 0.5 minutes. aug. 23 17:13:46.529 pppd[14438]: Sent 1866 bytes, received 1241 bytes. aug. 23 17:13:46.529 pppd[14438]: Connection terminated. aug. 23 17:13:46.562 ipsec_setup: Stopping Openswan IPsec... aug. 23 17:13:46.576 pppd[14438]: Exit.

    Read the article

  • Setup VPN issue on Ubuntu Server 12.04

    - by Yozone W.
    I have a problem with setup VPN server on my Ubuntu VPS, here is my server environments: Ubuntu Server 12.04 x86_64 xl2tpd 1.3.1+dfsg-1 pppd 2.4.5-5ubuntu1 openswan 1:2.6.38-1~precise1 After install software and configuration: ipsec verify Checking your system to see if IPsec got installed and started correctly: Version check and ipsec on-path [OK] Linux Openswan U2.6.38/K3.2.0-24-virtual (netkey) Checking for IPsec support in kernel [OK] SAref kernel support [N/A] NETKEY: Testing XFRM related proc values [OK] [OK] [OK] Checking that pluto is running [OK] Pluto listening for IKE on udp 500 [OK] Pluto listening for NAT-T on udp 4500 [OK] Checking for 'ip' command [OK] Checking /bin/sh is not /bin/dash [WARNING] Checking for 'iptables' command [OK] Opportunistic Encryption Support [DISABLED] /var/log/auth.log message: Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [RFC 3947] method set to=115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike] meth=114, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-08] meth=113, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-07] meth=112, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-06] meth=111, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-05] meth=110, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-04] meth=109, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-03] meth=108, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02] meth=107, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02_n] meth=106, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: ignoring Vendor ID payload [FRAGMENTATION 80000000] Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [Dead Peer Detection] Oct 16 06:50:54 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: responding to Main Mode from unknown peer [My IP Address] Oct 16 06:50:54 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: transition from state STATE_MAIN_R0 to state STATE_MAIN_R1 Oct 16 06:50:54 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: STATE_MAIN_R1: sent MR1, expecting MI2 Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: NAT-Traversal: Result using draft-ietf-ipsec-nat-t-ike (MacOS X): peer is NATed Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: transition from state STATE_MAIN_R1 to state STATE_MAIN_R2 Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: STATE_MAIN_R2: sent MR2, expecting MI3 Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: ignoring informational payload, type IPSEC_INITIAL_CONTACT msgid=00000000 Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: Main mode peer ID is ID_IPV4_ADDR: '192.168.12.52' Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: switched from "L2TP-PSK-NAT" to "L2TP-PSK-NAT" Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: deleting connection "L2TP-PSK-NAT" instance with peer [My IP Address] {isakmp=#0/ipsec=#0} Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: transition from state STATE_MAIN_R2 to state STATE_MAIN_R3 Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: new NAT mapping for #5, was [My IP Address]:2251, now [My IP Address]:2847 Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: STATE_MAIN_R3: sent MR3, ISAKMP SA established {auth=OAKLEY_PRESHARED_KEY cipher=aes_256 prf=oakley_sha group=modp1024} Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: Dead Peer Detection (RFC 3706): enabled Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: the peer proposed: [My Server IP Address]/32:17/1701 -> 192.168.12.52/32:17/0 Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: NAT-Traversal: received 2 NAT-OA. using first, ignoring others Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: responding to Quick Mode proposal {msgid:8579b1fb} Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: us: [My Server IP Address]<[My Server IP Address]>:17/1701 Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: them: [My IP Address][192.168.12.52]:17/65280===192.168.12.52/32 Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: transition from state STATE_QUICK_R0 to state STATE_QUICK_R1 Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: STATE_QUICK_R1: sent QR1, inbound IPsec SA installed, expecting QI2 Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: Dead Peer Detection (RFC 3706): enabled Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: transition from state STATE_QUICK_R1 to state STATE_QUICK_R2 Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: STATE_QUICK_R2: IPsec SA established transport mode {ESP=>0x08bda158 <0x4920a374 xfrm=AES_256-HMAC_SHA1 NATOA=192.168.12.52 NATD=[My IP Address]:2847 DPD=enabled} Oct 16 06:51:16 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: received Delete SA(0x08bda158) payload: deleting IPSEC State #6 Oct 16 06:51:16 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: ERROR: netlink XFRM_MSG_DELPOLICY response for flow eroute_connection delete included errno 2: No such file or directory Oct 16 06:51:16 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: received and ignored informational message Oct 16 06:51:16 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: received Delete SA payload: deleting ISAKMP State #5 Oct 16 06:51:16 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address]: deleting connection "L2TP-PSK-NAT" instance with peer [My IP Address] {isakmp=#0/ipsec=#0} Oct 16 06:51:16 vpn pluto[3963]: packet from [My IP Address]:2847: received and ignored informational message xl2tpd -D message: xl2tpd[4289]: Enabling IPsec SAref processing for L2TP transport mode SAs xl2tpd[4289]: IPsec SAref does not work with L2TP kernel mode yet, enabling forceuserspace=yes xl2tpd[4289]: setsockopt recvref[30]: Protocol not available xl2tpd[4289]: This binary does not support kernel L2TP. xl2tpd[4289]: xl2tpd version xl2tpd-1.3.1 started on vpn.netools.me PID:4289 xl2tpd[4289]: Written by Mark Spencer, Copyright (C) 1998, Adtran, Inc. xl2tpd[4289]: Forked by Scott Balmos and David Stipp, (C) 2001 xl2tpd[4289]: Inherited by Jeff McAdams, (C) 2002 xl2tpd[4289]: Forked again by Xelerance (www.xelerance.com) (C) 2006 xl2tpd[4289]: Listening on IP address [My Server IP Address], port 1701 Then it just stopped here, and have no any response. I can't connect VPN on my mac client, the /var/log/system.log message: Oct 16 15:17:36 azone-iMac.local configd[17]: SCNC: start, triggered by SystemUIServer, type L2TP, status 0 Oct 16 15:17:36 azone-iMac.local pppd[3799]: pppd 2.4.2 (Apple version 596.13) started by azone, uid 501 Oct 16 15:17:38 azone-iMac.local pppd[3799]: L2TP connecting to server 'vpn.netools.me' ([My Server IP Address])... Oct 16 15:17:38 azone-iMac.local pppd[3799]: IPSec connection started Oct 16 15:17:38 azone-iMac.local racoon[359]: Connecting. Oct 16 15:17:38 azone-iMac.local racoon[359]: IPSec Phase1 started (Initiated by me). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKE Packet: transmit success. (Initiator, Main-Mode message 1). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKE Packet: receive success. (Initiator, Main-Mode message 2). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKE Packet: transmit success. (Initiator, Main-Mode message 3). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKE Packet: receive success. (Initiator, Main-Mode message 4). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKE Packet: transmit success. (Initiator, Main-Mode message 5). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKEv1 Phase1 AUTH: success. (Initiator, Main-Mode Message 6). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKE Packet: receive success. (Initiator, Main-Mode message 6). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKEv1 Phase1 Initiator: success. (Initiator, Main-Mode). Oct 16 15:17:38 azone-iMac.local racoon[359]: IPSec Phase1 established (Initiated by me). Oct 16 15:17:39 azone-iMac.local racoon[359]: IPSec Phase2 started (Initiated by me). Oct 16 15:17:39 azone-iMac.local racoon[359]: IKE Packet: transmit success. (Initiator, Quick-Mode message 1). Oct 16 15:17:39 azone-iMac.local racoon[359]: IKE Packet: receive success. (Initiator, Quick-Mode message 2). Oct 16 15:17:39 azone-iMac.local racoon[359]: IKE Packet: transmit success. (Initiator, Quick-Mode message 3). Oct 16 15:17:39 azone-iMac.local racoon[359]: IKEv1 Phase2 Initiator: success. (Initiator, Quick-Mode). Oct 16 15:17:39 azone-iMac.local racoon[359]: IPSec Phase2 established (Initiated by me). Oct 16 15:17:39 azone-iMac.local pppd[3799]: IPSec connection established Oct 16 15:17:59 azone-iMac.local pppd[3799]: L2TP cannot connect to the server Oct 16 15:17:59 azone-iMac.local racoon[359]: IPSec disconnecting from server [My Server IP Address] Oct 16 15:17:59 azone-iMac.local racoon[359]: IKE Packet: transmit success. (Information message). Oct 16 15:17:59 azone-iMac.local racoon[359]: IKEv1 Information-Notice: transmit success. (Delete IPSEC-SA). Oct 16 15:17:59 azone-iMac.local racoon[359]: IKE Packet: transmit success. (Information message). Oct 16 15:17:59 azone-iMac.local racoon[359]: IKEv1 Information-Notice: transmit success. (Delete ISAKMP-SA). Anyone help? Thanks a million!

    Read the article

< Previous Page | 1 2