Search Results

Search found 120 results on 5 pages for 'lars kerff'.

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

Page 2/5 | < Previous Page | 1 2 3 4 5  | Next Page >

  • SSH login to Cisco switch using Rancid times out

    - by Lars
    I have a 3560 switch that I have configured to accept SSH logins, and this works fine. However I cannot get Rancid to complete the login process to any of my switches using SSH. I get a timeout error after a minute or so. Telnet logins work fine with the same username and password. Here is my rancid setup in .cloginrc: add user * {myuser} add password * {strongAccessPassword} {strongEnablePassword} add method * ssh telnet Then, when I run bin/clogin 10.10.1.10 I get: # bin/clogin 10.10.1.10 10.10.1.10 spawn ssh -c 3des -x -l myuser 10.10.1.10 ############################################### Please authenticate. ############################################### Password: Error: TIMEOUT reached Again, when I do this using telnet as my preferred mothod in .cloginrc, it works without issue.

    Read the article

  • Skipping hardlinks when using TSM Backup

    - by Lars Haugseth
    We need to backup a filesystem with lots of hardlinks. Since there are several hardlinks for each "true" file, we would like to skip all the hardlinks when backing up the filesystem to avoid n exact copies of each file. The backup is done using Tivoli Storage Manager Backup, and we've been unable to get it to treat hardlinks as anything other than separate files to be backed up alongside each other. In case it's relevant for possible solutions, I'd like to note that it's possible to tell a hardlink from a proper file by the filename: foobarbaz-123.ext # file foobarbaz-123-1.ext # hardlink foobarbaz-123-2.ext # hardlink barbazfoo-456.ext # file barbazfoo-456-1.ext # hardlink barbazfoo-456-2.ext # hardlink barbazfoo-456-3.ext # hardlink That is, all hardlinks have two hyphens in the filename, where as proper files have just the one. The server is running Ubuntu Linux, and the files are situated on a gfs volume on our SAN.

    Read the article

  • Enable Server Status using Plesk 11

    - by Lars Ebert
    I am trying to get apaches server status to work with Plesk 11. But running sudo /usr/sbin/apache2ctl fullstatus results in: Forbidden You don't have permission to access /server-status on this server. __________________________________________________________________ Apache Server at localhost Port 80 'www-browser -dump http://localhost:80/server-status' failed. Maybe you need to install a package providing www-browser or you need to adjust the APACHE_LYNX variable in /etc/apache2/envvars How can I enable server status? So far I have tried to insert <Location /server-status> SetHandler server-status Order Deny,Allow Deny from all Allow from localhost </Location> into the httpd.conf, but I am not sure if it is active. I also tried adding it to /var/www/vhosts/somedomain/conf/vhost.conf but I do not know which domain I have to add this to, as fullstatus seems to query localhost directly. I guess I am a little confused by the use of vhost configuration in Plesk.

    Read the article

  • Slow ASP.NET site using IIS6

    - by lars
    Hi, I have two servers, one virtual and one physical, running the exact same site on both machines. Both machines are running on ~ 2% CPU load and very much RAM available for usage. Somehow the site, with cache turned off ofcourse, loads in ~ 500ms on the virtual machine (which is a dev-server by the way) but almost 3 full seconds on the physical machine. They're both running Server 2003, IIS6 aswell as asp.net version 2.0 Any ideas where I can start troubleshoot this? Best Regards LP

    Read the article

  • Not all events appear in Nagios history (archive)

    - by Lars
    in the "Host & Service history" of my check_mk interface I can see various events, but a lot of events are missing. On the default interface at "View Alert History For This Service" or in the logfiles /var/log/nagios/archives/*.log the same issue: I can see many events of the last days, but not all of them. In the /etc/nagios/nagios.cfg the options log_event_handlers, log_initial_status and log_passive_checks are set to 0, the other log_... options are set to 1. I don't think that any of these options causing the problem that not all events are logged. What could cause this problem?

    Read the article

  • Ubuntu - How to automount an external drive at a preconfigured mount point?

    - by Lars Haugseth
    Normally, when I attach an external USB drive to my Ubuntu system, the filesystem on it are automounted to /media/label. However, I'd like the filesystem to be mounted at a mount point of my choosing. I've added a line like this to my /etc/fstab: UUID=2BE905C238C1F724 /p ntfs-3g defaults 0 0 # Passport 320GB This allows me to manually mount the volume at /p by running sudo mount /p, however the filesystem is no longer automounted when the drive is attached to the PC. What do I need to do to get automount to this mount point to work, if at all possible?

    Read the article

  • Linux server: Dropped packets

    - by Lars
    I see dropped packets using ifconfig on my eth0 interface: eth0 Link encap:Ethernet HWaddr 00:15:17:0d:03:ca inet addr:10.0.1.2 Bcast:10.0.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:9000 Metric:1 RX packets:30268348 errors:0 dropped:70721 overruns:0 frame:0 TX packets:133076885 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:8699434077 (8.6 GB) TX bytes:194937313025 (194.9 GB) Interrupt:16 Memory:feae0000-feb00000 When i use ethtool -S i dont see anything wrong: NIC statistics: rx_packets: 30267138 tx_packets: 133074510 rx_bytes: 8699356158 tx_bytes: 194934147340 rx_broadcast: 35296 tx_broadcast: 5435 rx_multicast: 0 tx_multicast: 0 rx_errors: 0 tx_errors: 0 tx_dropped: 0 multicast: 0 collisions: 0 rx_length_errors: 0 rx_over_errors: 0 rx_crc_errors: 0 rx_frame_errors: 0 rx_no_buffer_count: 0 rx_missed_errors: 0 tx_aborted_errors: 0 tx_carrier_errors: 0 tx_fifo_errors: 0 tx_heartbeat_errors: 0 tx_window_errors: 0 tx_abort_late_coll: 0 tx_deferred_ok: 0 tx_single_coll_ok: 0 tx_multi_coll_ok: 0 tx_timeout_count: 0 tx_restart_queue: 0 rx_long_length_errors: 0 rx_short_length_errors: 0 rx_align_errors: 0 tx_tcp_seg_good: 5757001 tx_tcp_seg_failed: 0 rx_flow_control_xon: 8649 rx_flow_control_xoff: 62072 tx_flow_control_xon: 0 tx_flow_control_xoff: 0 rx_long_byte_count: 8699356158 rx_csum_offload_good: 30212111 rx_csum_offload_errors: 0 rx_header_split: 10857552 alloc_rx_buff_failed: 0 tx_smbus: 0 rx_smbus: 0 dropped_smbus: 0 rx_dma_failed: 0 tx_dma_failed: 0 I am running Ubuntu 12.04 with kernel 3.2.0-30-generic #48-Ubuntu SMP I have pinged every device on my internal network for about 24 hours, without packet loss. Also checked my router and my interface to the WAN, also no errors there. Does anyone have any clue?

    Read the article

  • How to calculate bandwidth limits per user on WiFi network

    - by Lars
    A typical 802.11g access point can provide around 25 Mbps of bandwidth. How is the bandwidth shared among the users? Furthermore, how many users can be served by a single access point using 802.11g in an environment with low interference, and average web activity from the users? The goal is to use bandwidth limitation to avoid starvation for some users in case some of the users start to download a file or stream HD video or some other bandwidth intensive activity. Can someone break down the math on this?

    Read the article

  • rdate for Windows 2008

    - by Lars D
    I need a command line tool that adjusts the time of a Windows 2008 server, using an internet clock. The purpose is to adjust the time in a script, when other apps from that script are not running. It is not an option to use the built-in NTP service because that makes some apps on this server fail - note, that this server is used in an industrial environment with no PCs on the network and no Windows update or similar applied. Any idea, anyone?

    Read the article

  • RAID 10 or RAID 5 for multiple VMs - what is the best choice?

    - by Lars Fastrup
    I have just ordered a new rig for my business. We do a lot of software development for Microsoft SharePoint and need the rig to run several virtual machines for development and test purposes. We will be using the free VMware ESXi for virtualization. For a start, we plan to build and start the following VMs - all with Windows Server 2008 R2 x64: Active Directory server MS SQL Server 2008 R2 Automated Build Server SharePoint 2010 Server for hosting our public Web site and our internal Intranet for a few people. The load on this server is going to be quite insignificant. 2xSharePoint 2007 development server 2xSharePoint 2010 development server Beyond that we will need to build several SharePoint farms for testing purposes. These VMs will only be started when needed. The specs of the new rig is: Dell R610 rack server 2xIntel XEON E5620 48GB RAM 6x146GB SAS drives Dell H700 RAID controller We believe the new server is going to make our VMs perform a lot better than our existing setup (2xIntel XEON, 16GB RAM, 2x500 GB SATA in RAID 1). But we are not sure about the RAID level for the new rig. Should we go for having the the 6x146GB SAS drives in a RAID 10 configuration or a RAID 5 configuration? RAID 10 seems to offer better write performance and lower risk of a RAID failure. But it comes at a cost of less drive space. Do we need RAID 10 or would RAID 5 also be a good choice for us?

    Read the article

  • Can't copy Ilias-folder via FQDN, but via ip-address?

    - by Lars
    I have an Ilias-Installation, which is available through two virtual hosts: the FQDN and the ip-address. The first server is ssl only, the second plain http. Both configuration files look the same except for the SSL-part: SSLEngine on SSLCertificateFile /etc/apache2/ssl/ilias.pem In the Ilias-Webinterface, I can copy a folder on the plain http. But if I try to copy the same folder on the ssl virtual host, I get the notice, that the copy was started (rough german translation here), but the folder does not show up. There are no errors in the error-logs of php or the webserver and as said, no differences beside the ssl-part. The guys at an ilias-forum did not have an idea, either. Any ideas in here?

    Read the article

  • Google Chrome and kerberos authentication against Apache

    - by Lars
    I've managed to get kerberos authentication to work now with Apache and Likewise Open but so far, Google Chrome doesn't seem to play fair. Unless I start it with chrome.exe --auth-server-whitelist="*company.com" it does only pop-up a login window but will not accept any credentials at all. As far as I know, the --auth-server-whitelist option should only be used when trying to get Single-Sign-On (SSO) to work, but if you are fine with a log-in window it should work directly out of the box, but so far it doesn't. This is the error I get in the apache logs. [Tue Dec 13 08:49:04 2011] [error] [client 192.168.1.15] failed to verify krb5 credentials: Unknown code krb5 7

    Read the article

  • Free, web based alternative to Visio?

    - by Lars
    I have used Visio to map out my network structure, and have used the export function to create an HTML page that is searchable by IP, hostname etc. This is a really nice tool and I use it often. However, I would like for users who do not use Internet Explorer to be able to use the search features. What are some alternatives to Visio here? I want to draw a network diagram where objects are searchable. Thanks!

    Read the article

  • Log onto a domain elsewhere

    - by Lars
    I am wondering if an user can log onto my domain outside the office, or are you only able to do this locally? (in the office) Can you be outside the town or even country login onto a company's domain? (windows server 2008)

    Read the article

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

< Previous Page | 1 2 3 4 5  | Next Page >