Search Results

Search found 342 results on 14 pages for 'mhz'.

Page 2/14 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• IBM Thinkpad 240 - Best way to boot from floppy to USB - Best Linux for 300 MHz 128 MB RAM 800x600 s

  - by zillion

  Mostly I still have that old 'ultraportable' laptop that is mostly like a pre-netbook era laptop and a friend and programmer needs a computer because the one he was using just broke and he has to wait until the new one arrive in 4-6 weeks ... This laptop has no LAN connection and CD-ROM so be prepared for a real challenge! All hardware is well supported on Windows XP (included drivers on the Windows XP CD) and on Linux out-of-the-box (but the screen need a special configuration.) Mostly any Linux that will work well with Skype (USB or regular headset), any MSN client and a text writer for code will do. What I have tested so far: Slitaz 2 don't boot because the floppy of GRUB4DOS don't see the USB drive (fully working and tested on my regular laptop), Damn Small Linux was working but was needing a special screen configuration that I don't remember (in the boot options of the floppy) and now I'm thinking about Puppy Linux that is seen to work totally out of the box with it but I will need an old Puppy version (1 or 2 I think) and the Wakepup floppy ... If you got some ideas to help or to try I'm open!

  Read the article

• Is this a normal operating temperature range for a New Third-Generation MacBook Air (2.13 MHz, 120 G

  - by doug

  Even with just my text editor open (no web browser) and maybe the terminal, the baseline temperature is usually above 40 C. When i open 4-5 browser tabs in Safari (even if none of Sites have Flash) the temp can quickly go over 50 C. (In addition, i am observing these temps even though i have turned the fan up to 3000 rpms). (i have install smcFanControl on my MBA so i can see the temp in the menu bar.) So this means my MBA is running much warmer than my MBP; and in practice, it means that i have to be very careful how i use my MBA. Of course if i load a Site with Flash, it just freaks out, and often quickly goes above 65 C (I've installed a flash blocker to avoid this). Is anyone else observing this behavior? I have checked the Apple boards and sure enough, there are a lot of complaints, but nothing from Apple.

  Read the article

• Ubuntu 12.04 connected to wireless network but internet not working

  - by A.J.

  I can connect to my house's wireless network just fine, but when I'm connected I can't browse the web. Firefox starts connecting to a site and then just poops out. This doesn't happen on my roommates' computers (running Windows) or on our 3DSes, so I know it's just my laptop. I already tried sudo dhclient -r sudo dhclient sudo ifconfig eth0 down sudo ifconfig eth0 up Results of a few commands I was asked to run in comments: ping -c 2 4.2.2.2 PING 4.2.2.2 (4.2.2.2) 56(84) bytes of data. ^C --- 4.2.2.2 ping statistics --- 2 packets transmitted, 0 received, 100% packet loss, time 1007ms ping -c 2 google.com PING google.com (173.194.33.38) 56(84) bytes of data. --- google.com ping statistics --- 2 packets transmitted, 0 received, 100% packet loss, time 1006ms nm-tool NetworkManager Tool State: connected (global) - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: atl1c State: unavailable Default: no HW Address: 88:AE:1D:6B:4E:E7 Capabilities: Carrier Detect: yes Speed: 100 Mb/s Wired Properties Carrier: off - Device: wlan0 [JUSTICE] ----------------------------------------------------- Type: 802.11 WiFi Driver: ath9k State: connected Default: yes HW Address: 1C:65:9D:65:C6:31 Capabilities: Speed: 1 Mb/s Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points (* = current AP) HOME-9B18: Infra, 00:26:F3:53:9B:18, Freq 2412 MHz, Rate 54 Mb/s, Strength 34 WPA WPA2 cougdad48 Network: Infra, 60:33:4B:E4:C4:5D, Freq 2437 MHz, Rate 54 Mb/s, Strength 22 WPA2 cougdad48 Guest Network: Infra, 66:33:4B:E4:C4:5D, Freq 2437 MHz, Rate 54 Mb/s, Strength 20 WPA2 belkin.ade: Infra, 94:44:52:FF:8A:DE, Freq 2457 MHz, Rate 54 Mb/s, Strength 20 WPA WPA2 *JUSTICE: Infra, 00:24:01:7B:9F:7E, Freq 2462 MHz, Rate 54 Mb/s, Strength 88 WEP CenturyLink: Infra, B2:B2:DC:8E:E2:58, Freq 2462 MHz, Rate 54 Mb/s, Strength 17 WPA WPA2 IPv4 Settings: Address: 192.168.0.11 Prefix: 24 (255.255.255.0) Gateway: 192.168.0.1 DNS: 192.168.0.1 (JUSTICE is my home's network.) ping -c 2 198.168.0.1 PING 198.168.0.1 (198.168.0.1) 56(84) bytes of data. --- 198.168.0.1 ping statistics --- 2 packets transmitted, 0 received, 100% packet loss, time 1007ms

  Read the article

• Cannot connect to Open WiFi hotspot created by Android

  - by Bibhas

  I'm trying to share my 3G data connection via WiFi hotspot. I have an open Hotspot running on my phone(Xperia Neo V - MT11i - Android 2.3.4). But I cannot connect to it from my Ubuntu system. Here is the syslog while I try to connect to it - NetworkManager[1077]: <info> Activation (wlan0) starting connection 'TheNeo' NetworkManager[1077]: <info> (wlan0): device state change: disconnected -> prepare (reason 'none') [30 40 0] NetworkManager[1077]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) scheduled... NetworkManager[1077]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) started... NetworkManager[1077]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) scheduled... NetworkManager[1077]: <info> Activation (wlan0) Stage 1 of 5 (Device Prepare) complete. NetworkManager[1077]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) starting... NetworkManager[1077]: <info> (wlan0): device state change: prepare -> config (reason 'none') [40 50 0] NetworkManager[1077]: <info> Activation (wlan0/wireless): connection 'TheNeo' requires no security. No secrets needed. NetworkManager[1077]: <info> Config: added 'ssid' value 'TheNeo' NetworkManager[1077]: <info> Config: added 'scan_ssid' value '1' NetworkManager[1077]: <info> Config: added 'key_mgmt' value 'NONE' NetworkManager[1077]: <info> Activation (wlan0) Stage 2 of 5 (Device Configure) complete. NetworkManager[1077]: <info> Config: set interface ap_scan to 1 NetworkManager[1077]: <info> (wlan0): supplicant interface state: inactive -> scanning wpa_supplicant[29352]: Trying to authenticate with 5c:b5:24:2f:d1:2f (SSID='TheNeo' freq=2462 MHz) NetworkManager[1077]: <info> (wlan0): supplicant interface state: scanning -> authenticating kernel: [17498.113553] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 1/3) kernel: [17498.310138] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 2/3) kernel: [17498.510069] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 3/3) kernel: [17498.710083] wlan0: direct probe to 5c:b5:24:2f:d1:2f timed out wpa_supplicant[29352]: Trying to authenticate with 5c:b5:24:2f:d1:2f (SSID='TheNeo' freq=2462 MHz) kernel: [17504.779927] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 1/3) kernel: [17504.976420] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 2/3) kernel: [17505.176379] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 3/3) kernel: [17505.376314] wlan0: direct probe to 5c:b5:24:2f:d1:2f timed out wpa_supplicant[29352]: Trying to authenticate with 5c:b5:24:2f:d1:2f (SSID='TheNeo' freq=2462 MHz) kernel: [17511.478385] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 1/3) kernel: [17511.674738] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 2/3) kernel: [17511.874655] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 3/3) kernel: [17512.074659] wlan0: direct probe to 5c:b5:24:2f:d1:2f timed out wpa_supplicant[29352]: Trying to authenticate with 5c:b5:24:2f:d1:2f (SSID='TheNeo' freq=2462 MHz) kernel: [17518.152643] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 1/3) kernel: [17518.349064] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 2/3) kernel: [17518.549051] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 3/3) kernel: [17518.748999] wlan0: direct probe to 5c:b5:24:2f:d1:2f timed out wpa_supplicant[29352]: Trying to authenticate with 5c:b5:24:2f:d1:2f (SSID='TheNeo' freq=2462 MHz) kernel: [17524.858896] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 1/3) kernel: [17525.055404] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 2/3) kernel: [17525.255387] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 3/3) kernel: [17525.455254] wlan0: direct probe to 5c:b5:24:2f:d1:2f timed out wpa_supplicant[29352]: Trying to authenticate with 5c:b5:24:2f:d1:2f (SSID='TheNeo' freq=2462 MHz) kernel: [17531.589176] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 1/3) kernel: [17531.785747] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 2/3) kernel: [17531.985724] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 3/3) kernel: [17532.185610] wlan0: direct probe to 5c:b5:24:2f:d1:2f timed out wpa_supplicant[29352]: Trying to authenticate with 5c:b5:24:2f:d1:2f (SSID='TheNeo' freq=2462 MHz) kernel: [17538.329257] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 1/3) kernel: [17538.528003] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 2/3) kernel: [17538.728024] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 3/3) kernel: [17538.927922] wlan0: direct probe to 5c:b5:24:2f:d1:2f timed out wpa_supplicant[29352]: Trying to authenticate with 5c:b5:24:2f:d1:2f (SSID='TheNeo' freq=2462 MHz) kernel: [17545.022036] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 1/3) kernel: [17545.218339] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 2/3) kernel: [17545.418319] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 3/3) kernel: [17545.618206] wlan0: direct probe to 5c:b5:24:2f:d1:2f timed out wpa_supplicant[29352]: Trying to authenticate with 5c:b5:24:2f:d1:2f (SSID='TheNeo' freq=2462 MHz) kernel: [17551.724177] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 1/3) kernel: [17551.920685] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 2/3) kernel: [17552.120597] wlan0: direct probe to 5c:b5:24:2f:d1:2f (try 3/3) kernel: [17552.320526] wlan0: direct probe to 5c:b5:24:2f:d1:2f timed out NetworkManager[1077]: <warn> Activation (wlan0/wireless): association took too long, failing activation. NetworkManager[1077]: <info> (wlan0): device state change: config -> failed (reason 'supplicant-timeout') [50 120 11] NetworkManager[1077]: <warn> Activation (wlan0) failed for access point (TheNeo) NetworkManager[1077]: <warn> Activation (wlan0) failed. NetworkManager[1077]: <info> (wlan0): device state change: failed -> disconnected (reason 'none') [120 30 0] NetworkManager[1077]: <info> (wlan0): deactivating device (reason 'none') [0] NetworkManager[1077]: <info> (wlan0): supplicant interface state: authenticating -> disconnected NetworkManager[1077]: <warn> Couldn't disconnect supplicant interface: This interface is not connected. Why is direct probe to 5c:b5:24:2f:d1:2f timed out? Any idea?

  Read the article

• dmidecode showing more ram slots than available?

  - by Jestep

  I have some failing RAM in a server and I ran dmidecode to figure out what tyoe of RAM I needed to replace it with. The server has 6 RAM slots, 4 of which are in use. When I run dmidecode this is what I get. dmidecode 2.10 SMBIOS 2.4 present. Handle 0x001F, DMI type 17, 27 bytes Memory Device Array Handle: 0x001E Error Information Handle: No Error Total Width: 72 bits Data Width: 64 bits Size: 2048 MB Form Factor: DIMM Set: 1 Locator: JXXX Bank Locator: DIMM 00 Type: DDR2 Type Detail: Synchronous Speed: 667 MHz Manufacturer: Not Specified Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified Handle 0x0020, DMI type 17, 27 bytes Memory Device Array Handle: 0x001E Error Information Handle: No Error Total Width: 72 bits Data Width: 64 bits Size: 2048 MB Form Factor: DIMM Set: 1 Locator: JXXX Bank Locator: DIMM 01 Type: DDR2 Type Detail: Synchronous Speed: 667 MHz Manufacturer: Not Specified Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified Handle 0x0021, DMI type 17, 27 bytes Memory Device Array Handle: 0x001E Error Information Handle: No Error Total Width: Unknown Data Width: Unknown Size: No Module Installed Form Factor: DIMM Set: 1 Locator: JXXX Bank Locator: DIMM 02 Type: DDR2 Type Detail: Synchronous Speed: 667 MHz Manufacturer: Not Specified Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified Handle 0x0022, DMI type 17, 27 bytes Memory Device Array Handle: 0x001E Error Information Handle: No Error Total Width: Unknown Data Width: Unknown Size: No Module Installed Form Factor: DIMM Set: 1 Locator: JXXX Bank Locator: DIMM 03 Type: DDR2 Type Detail: Synchronous Speed: 667 MHz Manufacturer: Not Specified Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified Handle 0x0023, DMI type 17, 27 bytes Memory Device Array Handle: 0x001E Error Information Handle: No Error Total Width: 72 bits Data Width: 64 bits Size: 2048 MB Form Factor: DIMM Set: 1 Locator: JXXX Bank Locator: DIMM 10 Type: DDR2 Type Detail: Synchronous Speed: 667 MHz Manufacturer: Not Specified Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified Handle 0x0024, DMI type 17, 27 bytes Memory Device Array Handle: 0x001E Error Information Handle: No Error Total Width: 72 bits Data Width: 64 bits Size: 2048 MB Form Factor: DIMM Set: 1 Locator: JXXX Bank Locator: DIMM 11 Type: DDR2 Type Detail: Synchronous Speed: 667 MHz Manufacturer: Not Specified Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified Handle 0x0025, DMI type 17, 27 bytes Memory Device Array Handle: 0x001E Error Information Handle: No Error Total Width: Unknown Data Width: Unknown Size: No Module Installed Form Factor: DIMM Set: 1 Locator: JXXX Bank Locator: DIMM 12 Type: DDR2 Type Detail: Synchronous Speed: 667 MHz Manufacturer: Not Specified Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified Handle 0x0026, DMI type 17, 27 bytes Memory Device Array Handle: 0x001E Error Information Handle: No Error Total Width: Unknown Data Width: Unknown Size: No Module Installed Form Factor: DIMM Set: 1 Locator: JXXX Bank Locator: DIMM 13 Type: DDR2 Type Detail: Synchronous Speed: 667 MHz Manufacturer: Not Specified Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified Does anyone know why it would show 8 slots, with 4 empty instead of 6 slots with 2 empty? Also, but my records and by other tools, the server has 16Gb and not 8Gb in it currently. grep MemTotal /proc/meminfo MemTotal: 16435808 kB The board is a Tyan S5372-LC, running CentOS 5.4 x64. Also, my error log is showing errors in bank 6. Is there any way to determine which slot bank 6 is in via: dmidecode?

  Read the article

• Xorg.conf (nvidia) Second Monitor getting settings of first

  - by HennyH

  I've been spending the weekend (and some time before that) trying to set up my Korean QHD270 and Benq G2222HDL monitors with Ubuntu 13.10. With the nouveau drivers install both monitor function perfectly fine. After installing the nvidia drivers the Benq works but the QHD270 does not. Now, after days of struggling I managed to get the QHD270 to work following a mixture of blogs, particularly; this one and learnitwithme. Now, unfortunatly my G2222HDL does not work. I fixed the QHD270 by supplying a custom EDID, my xorg.conf looks like so (excluding keyboard and mouse): Section "ServerLayout" Identifier "Layout0" Screen "Default Screen" 0 0 InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" EndSection Section "Monitor" Identifier "Configured Monitor" EndSection Section "Device" Identifier "Configured Video Device" Driver "nvidia" Option "CustomEDID" "DFP:/etc/X11/edid-shimian.bin" EndSection Section "Screen" Identifier "Default Screen" Device "Configured Video Device" Monitor "Configured Monitor" EndSection Now, I tried defining a new Device,Monitor and Screen then in ServerLayout adding Screen "Second Screen" RightOf "Default Screen", but after doing so neither monitor worked. Hoping to fix the issue using a GUI based tool I opened up NVIDIA X Server Settings, which shows my current layout as: It seems that something is being output to the monitor, as suggested by my print screen: Any help would be greatly appreciated. Output of xrandr: Screen 0: minimum 8 x 8, current 5120 x 1440, maximum 16384 x 16384 DVI-I-0 disconnected (normal left inverted right x axis y axis) DVI-I-1 connected primary 2560x1440+0+0 (normal left inverted right x axis y axis) 597mm x 336mm 2560x1440 60.0*+ HDMI-0 disconnected (normal left inverted right x axis y axis) DP-0 disconnected (normal left inverted right x axis y axis) DVI-D-0 connected 2560x1440+2560+0 (normal left inverted right x axis y axis) 597mm x 336mm 2560x1440 60.0*+ DP-1 disconnected (normal left inverted right x axis y axis) And an extract from my log file (perhaps this is relevant?) [ 7.862] (--) NVIDIA(0): Valid display device(s) on GeForce GTX 680 at PCI:2:0:0 [ 7.862] (--) NVIDIA(0): CRT-0 [ 7.862] (--) NVIDIA(0): ACB QHD270 (DFP-0) (boot, connected) [ 7.862] (--) NVIDIA(0): DFP-1 [ 7.862] (--) NVIDIA(0): DFP-2 [ 7.862] (--) NVIDIA(0): DFP-3 [ 7.862] (--) NVIDIA(0): DFP-4 [ 7.862] (--) NVIDIA(0): CRT-0: 400.0 MHz maximum pixel clock [ 7.862] (--) NVIDIA(0): ACB QHD270 (DFP-0): 330.0 MHz maximum pixel clock [ 7.862] (--) NVIDIA(0): ACB QHD270 (DFP-0): Internal Dual Link TMDS [ 7.862] (--) NVIDIA(0): DFP-1: 165.0 MHz maximum pixel clock [ 7.862] (--) NVIDIA(0): DFP-1: Internal Single Link TMDS [ 7.862] (--) NVIDIA(0): DFP-2: 165.0 MHz maximum pixel clock [ 7.862] (--) NVIDIA(0): DFP-2: Internal Single Link TMDS [ 7.862] (--) NVIDIA(0): DFP-3: 330.0 MHz maximum pixel clock [ 7.862] (--) NVIDIA(0): DFP-3: Internal Single Link TMDS [ 7.862] (--) NVIDIA(0): DFP-4: 960.0 MHz maximum pixel clock [ 7.862] (--) NVIDIA(0): DFP-4: Internal DisplayPort

  Read the article

• What are the quality metrics for RAM?

  - by Hi-Tech KitKat Android

  I have searched RAM and i found there are given some specification for the same capacity RAM, What are the difference and performance comparison between these? Like RAM1 General Brand Transcend Memory Type 2 GB (8 x 128 MB) DDR2 DIMM Memory Standard DDR2-800/PC-6400 Compatible Device PC Pins 240-pin Burst Length 4, 8 Buffered/Unbuffered Unbuffered Memory Memory Clock 400 MHz Technology DDR2 SDRAM Memory CAS Latency 4, 5, 6 RAM 2 General Brand Transcend Memory Type 2 GB (8 x 128 MB) DDR2 DIMM Memory Standard DDR2-667/PC2-5300 Compatible Device PC Pins 240-pin Burst Length 4, 8 Buffered/Unbuffered Unbuffered Memory Memory Clock 333 MHz Technology DDR2 SDRAM Memory CAS Latency 3, 4, 5 RAM3 General Brand Kingston Memory Type 2 GB (64 x 256 MB) 800 MHz DDR2 DIMM Compatible Device PC Pins 240-pin Error Check Non-ECC Buffered/Unbuffered Unbuffered Memory Memory Clock 200 MHz Technology DDR2 SDRAM Memory CAS Latency 6 What are the affect of the following Memory Type(given as 8 x 128 MB) Memory Clock (given in MHz) CAS Latency (given as 4,5,6) my Requirement is 2 GB DDR2 Type Desktop Please help

  Read the article

• Does adding 1066Mhz DDR3 SODIMM to a 1600Mhz FSB laptop make sense?

  - by Alain Pannetier

  My previous laptop had 4x4GB 1066 Mhz DDR3. My new laptop instead has only 2x4GB 1600 Mhz DDR3. Using dmidecode I gather my FSB is set to 2300Mhz. Max Speed: 3800 MHz Current Speed: 2300 MHz 2 questions: Can somebody confirm I can safely add two "old" 1066Mhz modules to my new laptop before I treat myself to faster DDR3 modules? I understand this should not slow down the faster 2 1600 Mhz DDR3 modules. Correct? If this is of any relevance, I'm running Linux Mint Maya.

  Read the article

• Can anyone explain these differences between two similar i7 processors? [closed]

  - by Brian Frost

  I have two systems I've just built. They both have i7 processors and Asus P8Z77 motherboards. When I run a simple processor loop benchmark that I wrote in Delphi some time back I get one machine showing nealry twice as fast as the other. I then used CPU-Z to dump me the details of the hardware and I see that the fast machine shows: Processor 1 ID = 0 Number of cores 4 (max 8) Number of threads 8 (max 16) Name Intel Core i7 2700K Codename Sandy Bridge Specification Intel(R) Core(TM) i7-2700K CPU @ 3.50GHz Package (platform ID) Socket 1155 LGA (0x1) CPUID 6.A.7 Extended CPUID 6.2A Core Stepping D2 Technology 32 nm TDP Limit 95 Watts Core Speed 3610.7 MHz Multiplier x FSB 36.0 x 100.3 MHz Stock frequency 3500 MHz the slow machine shows: Processor 1 ID = 0 Number of cores 4 (max 8) Number of threads 8 (max 16) Name Intel Core i7 2600K Codename Sandy Bridge Specification Intel(R) Core(TM) i7-2600K CPU @ 3.40GHz Package (platform ID) Socket 1155 LGA (0x1) CPUID 6.A.7 Extended CPUID 6.2A Core Stepping D2 Technology 32 nm TDP Limit 95 Watts Core Speed 1648.2 MHz Multiplier x FSB 16.0 x 103.0 MHz Stock frequency 3400 MHz i.e the slow machine has a 2600k to the fast machine 2700k. The very different "Multiplier x FSB" must be significant but I dont understand how two processors with a very 'similar' number can be so different. To get the machines the same must I copy the processors or is there some clever setting that I can change? Thanks for any help. Brian.

  Read the article

• Best Processor for MediaSmart Server?

  - by Kent Boogaart

  I'm trying to figure out what the best possible processor is that I can stick in my HP MediaSmart server. I'm clueless when it comes to correlating CPUs to motherboards. I suspect it's the socket type I care about, but I worry that there's more to it. CPU-Z gives me (excerpt): Processors Information ------------------------------------------------------------------------- Processor 1 ID = 0 Number of cores 1 (max 1) Number of threads 1 (max 1) Name AMD Sempron LE-1150 Codename Sparta Specification AMD Sempron(tm) Processor LE-1150 Package Socket AM2 (940) CPUID F.F.1 Extended CPUID F.7F Brand ID 1 Core Stepping DH-G1 Technology 65 nm Core Speed 1000.0 MHz Multiplier x FSB 5.0 x 200.0 MHz HT Link speed 800.0 MHz Stock frequency 2000 MHz Instructions sets MMX (+), 3DNow! (+), SSE, SSE2, SSE3, x86-64 L1 Data cache 64 KBytes, 2-way set associative, 64-byte line size L1 Instruction cache 64 KBytes, 2-way set associative, 64-byte line size L2 cache 256 KBytes, 16-way set associative, 64-byte line size FID/VID Control yes Max FID 10.0x Max VID 1.350 V P-State FID 0x2 - VID 0x12 (5.0x - 1.100 V) P-State FID 0xA - VID 0x0C (9.0x - 1.250 V) P-State FID 0xC - VID 0x0A (10.0x - 1.300 V) K8 Thermal sensor yes K8 Revision ID 6.0 Attached device PCI device at bus 0, device 24, function 0 Attached device PCI device at bus 0, device 24, function 1 Attached device PCI device at bus 0, device 24, function 2 Attached device PCI device at bus 0, device 24, function 3 Chipset ------------------------------------------------------------------------- Northbridge SiS 761GX rev. 02 Southbridge SiS 966 rev. 59 Graphic Interface AGP AGP Revision 3.0 AGP Transfer Rate 8x AGP SBA supported, enabled Memory Type DDR2 Memory Size 2048 MBytes Channels Single Memory Frequency 200.0 MHz (CPU/5) CAS# latency (CL) 5.0 RAS# to CAS# delay (tRCD) 5 RAS# Precharge (tRP) 5 Cycle Time (tRAS) 15 Bank Cycle Time (tRC) 21 Command Rate (CR) 1T DMI ------------------------------------------------------------------------- DMI BIOS vendor Phoenix Technologies, LTD version R03 date 05/08/2008 DMI System Information manufacturer HP product MediaSmart Server version unknown serial CN68330DGH UUID A482007B-B0CC7593-DD11736A-407B7067 DMI Baseboard vendor Wistron model SJD4 revision A.0 serial unknown DMI System Enclosure manufacturer HP chassis type Desktop chassis serial unknown DMI Processor manufacturer AMD model AMD Sempron(tm) Processor LE-1150 clock speed 2000.0 MHz FSB speed 200.0 MHz multiplier 10.0x DMI Memory Controller correction 64-bit ECC Max module size 4096 MBytes DMI Memory Module designation A0 size 2048 MBytes (double bank) DMI Memory Module designation A1 DMI Memory Module designation A2 DMI Memory Module designation A3 DMI Port Connector designation PS/2 Mouse (internal) port type Mouse Port connector PS/2 connector PS/2 DMI Port Connector designation USB0 (external) port type USB DMI Physical Memory Array location Motherboard usage System Memory correction None max capacity 16384 MBytes max# of devices 4 DMI Memory Device designation A0 format DIMM type unknown total width 64 bits data width 64 bits size 2048 MBytes DMI Memory Device designation A1 format DIMM type unknown total width 64 bits data width 64 bits DMI Memory Device designation A2 format DIMM type unknown total width 64 bits data width 64 bits DMI Memory Device designation A3 format DIMM type unknown total width 64 bits data width 64 bits How do I figure out what options I have for an upgrade?

  Read the article

• Could not connect to wireless unitl reboot (nl80211)

  - by user107410

  I'm using Samsung NP900X3C. I have problem with occasionally connecting to WIFI, with Ubuntu 12.10. Sometimes my computer could not connect to WIFI "blab", neither after reboot computer. Only solution is to restart WIFI hotspot. It's public WIFI, used by many users, that don't have that problem. My /var/log/syslog: Nov 12 10:09:39 k15 wpa_supplicant[1308]: wlan0: SME: Trying to authenticate with 64:70:02:89:7c:d7 (SSID='blab' freq=2427 MHz) Nov 12 10:09:39 k15 kernel: [ 8.908610] wlan0: authenticate with 64:70:02:89:7c:d7 Nov 12 10:09:39 k15 NetworkManager[1004]: <info> (wlan0): supplicant interface state: scanning -> authenticating Nov 12 10:09:39 k15 kernel: [ 8.915032] wlan0: send auth to 64:70:02:89:7c:d7 (try 1/3) Nov 12 10:09:39 k15 wpa_supplicant[1308]: wlan0: Trying to associate with 64:70:02:89:7c:d7 (SSID='blab' freq=2427 MHz) Nov 12 10:09:39 k15 kernel: [ 8.916753] wlan0: authenticated Nov 12 10:09:39 k15 kernel: [ 8.916839] wlan0: waiting for beacon from 64:70:02:89:7c:d7 Nov 12 10:09:39 k15 NetworkManager[1004]: <info> (wlan0): supplicant interface state: authenticating -> associating Nov 12 10:09:39 k15 NetworkManager[1004]: <info> (wlan0): supplicant interface state: associating -> disconnected Nov 12 10:09:39 k15 NetworkManager[1004]: <info> (wlan0): supplicant interface state: disconnected -> scanning Nov 12 10:09:42 k15 wpa_supplicant[1308]: wlan0: SME: Trying to authenticate with 64:70:02:89:7c:d7 (SSID='blab' freq=2427 MHz) Nov 12 10:09:42 k15 kernel: [ 12.386212] wlan0: authenticate with 64:70:02:89:7c:d7 Nov 12 10:09:42 k15 wpa_supplicant[1308]: wlan0: Trying to associate with 64:70:02:89:7c:d7 (SSID='blab' freq=2427 MHz) Nov 12 10:09:42 k15 kernel: [ 12.389114] wlan0: send auth to 64:70:02:89:7c:d7 (try 1/3) Nov 12 10:09:42 k15 kernel: [ 12.391021] wlan0: authenticated Nov 12 10:09:42 k15 NetworkManager[1004]: <info> (wlan0): supplicant interface state: scanning -> authenticating Nov 12 10:09:42 k15 kernel: [ 12.391332] wlan0: waiting for beacon from 64:70:02:89:7c:d7 Nov 12 10:09:42 k15 NetworkManager[1004]: <info> (wlan0): supplicant interface state: authenticating -> associating Nov 12 10:09:43 k15 NetworkManager[1004]: <info> (wlan0): supplicant interface state: associating -> disconnected Nov 12 10:09:43 k15 NetworkManager[1004]: <info> (wlan0): supplicant interface state: disconnected -> scanning Nov 12 10:09:46 k15 wpa_supplicant[1308]: wlan0: SME: Trying to authenticate with 64:70:02:89:7c:d7 (SSID='blab' freq=2427 MHz) and after restart WiFi, I could connect: Nov 12 10:11:51 k15 NetworkManager[1004]: <info> (wlan0): supplicant interface state: inactive -> scanning Nov 12 10:11:55 k15 wpa_supplicant[1308]: wlan0: SME: Trying to authenticate with 64:70:02:89:7c:d7 (SSID='blab' freq=2427 MHz) Nov 12 10:11:55 k15 kernel: [ 144.445154] wlan0: authenticate with 64:70:02:89:7c:d7 Nov 12 10:11:55 k15 kernel: [ 144.453994] wlan0: send auth to 64:70:02:89:7c:d7 (try 1/3) Nov 12 10:11:55 k15 wpa_supplicant[1308]: wlan0: Trying to associate with 64:70:02:89:7c:d7 (SSID='blab' freq=2427 MHz) Nov 12 10:11:55 k15 NetworkManager[1004]: <info> (wlan0): supplicant interface state: scanning -> authenticating Nov 12 10:11:55 k15 kernel: [ 144.455860] wlan0: authenticated Nov 12 10:11:55 k15 kernel: [ 144.458681] wlan0: associate with 64:70:02:89:7c:d7 (try 1/3) Nov 12 10:11:55 k15 NetworkManager[1004]: <info> (wlan0): supplicant interface state: authenticating -> associating Nov 12 10:11:55 k15 kernel: [ 144.462799] wlan0: RX AssocResp from 64:70:02:89:7c:d7 (capab=0x431 status=0 aid=9) Nov 12 10:11:55 k15 kernel: [ 144.486368] wlan0: associated Nov 12 10:11:55 k15 wpa_supplicant[1308]: wlan0: Associated with 64:70:02:89:7c:d7 Nov 12 10:11:55 k15 kernel: [ 144.487435] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready Nov 12 10:11:55 k15 NetworkManager[1004]: <info> (wlan0): supplicant interface state: associating -> associated Nov 12 10:11:55 k15 NetworkManager[1004]: <info> (wlan0): supplicant interface state: associated -> 4-way handshake This problem is appearing regulary. My WiFi device control is nl80211. Nov 12 10:09:32 k15 NetworkManager[1004]: <info> (wlan0): using nl80211 for WiFi device control Nov 12 10:09:32 k15 NetworkManager[1004]: <warn> (wlan0): driver supports Access Point (AP) mode Nov 12 10:09:32 k15 NetworkManager[1004]: <info> (wlan0): new 802.11 WiFi device (driver: 'iwlwifi' ifindex: 3) Nov 12 10:09:32 k15 NetworkManager[1004]: <info> (wlan0): exported as /org/freedesktop/NetworkManager/Devices/0 Nov 12 10:09:32 k15 NetworkManager[1004]: <info> (wlan0): now managed Nov 12 10:09:32 k15 NetworkManager[1004]: <info> (wlan0): device state change: unmanaged -> unavailable (reason 'managed') [10 20 2] Nov 12 10:09:32 k15 NetworkManager[1004]: <info> (wlan0): bringing up device.

  Read the article

• Wireless Connected But No Internet Connection (Ubuntu 12.04)

  - by Zxy

  I am using same network for 2 days and everything was normal. However, today even though it shows me as connected to the network, I do not have internet connection. If I use ethernet cable instead of wireless, I am still able to connect to the internet. Also my friends are able to connect to the wireless network and they can get internet connection. I did not update or install anything since yesterday. Therefore I do not have any idea why it is happening. Here is some information about my connection: I will be appreciate to any kind of help. root@ghostrider:/etc/resolvconf# ping 127.0.0.1 PING 127.0.0.1 (127.0.0.1) 56(84) bytes of data. 64 bytes from 127.0.0.1: icmp_req=1 ttl=64 time=0.042 ms 64 bytes from 127.0.0.1: icmp_req=2 ttl=64 time=0.023 ms 64 bytes from 127.0.0.1: icmp_req=3 ttl=64 time=0.036 ms 64 bytes from 127.0.0.1: icmp_req=4 ttl=64 time=0.040 ms ^C --- 127.0.0.1 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 2998ms rtt min/avg/max/mdev = 0.023/0.035/0.042/0.008 ms root@ghostrider:/etc/resolvconf# ping 192.168.1.3 PING 192.168.1.3 (192.168.1.3) 56(84) bytes of data. ^C --- 192.168.1.3 ping statistics --- 19 packets transmitted, 0 received, 100% packet loss, time 18143ms root@ghostrider:/etc/resolvconf# ping 8.8.8.8 PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data. ^C --- 8.8.8.8 ping statistics --- 11 packets transmitted, 0 received, 100% packet loss, time 10079ms root@ghostrider:/etc/resolvconf# cat /etc/lsb-release; uname -a DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION="Ubuntu 12.04 LTS" Linux ghostrider 3.2.0-24-generic-pae #39-Ubuntu SMP Mon May 21 18:54:21 UTC 2012 i686 i686 i386 GNU/Linux root@ghostrider:/etc/resolvconf# lspci -nnk | grep -iA2 net 03:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR8131 Gigabit Ethernet [1969:1063] (rev c0) Subsystem: Lenovo Device [17aa:3956] Kernel driver in use: atl1c -- 04:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller [14e4:4727] (rev 01) Subsystem: Broadcom Corporation Device [14e4:0510] Kernel driver in use: wl root@ghostrider:/etc/resolvconf# lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 007: ID 0489:e00d Foxconn / Hon Hai Bus 001 Device 004: ID 1c7a:0801 LighTuning Technology Inc. Fingerprint Reader Bus 001 Device 005: ID 064e:f219 Suyin Corp. Bus 002 Device 010: ID 0424:2412 Standard Microsystems Corp. Bus 002 Device 004: ID 046d:c52b Logitech, Inc. Unifying Receiver Bus 002 Device 011: ID 0403:6010 Future Technology Devices International, Ltd FT2232C Dual USB-UART/FIFO IC root@ghostrider:/etc/resolvconf# iwconfig lo no wireless extensions. eth1 IEEE 802.11 ESSID:"PoliTekno" Mode:Managed Frequency:2.462 GHz Access Point: 00:16:E3:40:C3:E4 Bit Rate=54 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=5/5 Signal level=-52 dBm Noise level=-97 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 eth0 no wireless extensions. root@ghostrider:/etc/resolvconf# rfkill list all 0: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: no 1: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 2: ideapad_bluetooth: Bluetooth Soft blocked: no Hard blocked: no 5: hci0: Bluetooth Soft blocked: no Hard blocked: no root@ghostrider:/etc/resolvconf# lsmod Module Size Used by nls_iso8859_1 12617 0 nls_cp437 12751 0 vfat 17308 0 fat 55605 1 vfat usb_storage 39646 0 uas 17828 0 snd_hda_codec_realtek 174055 1 rfcomm 38139 12 parport_pc 32114 0 ppdev 12849 0 bnep 17830 2 joydev 17393 0 ftdi_sio 35859 1 usbserial 37173 3 ftdi_sio snd_hda_intel 32765 3 snd_hda_codec 109562 2 snd_hda_codec_realtek,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec acer_wmi 23612 0 hid_logitech_dj 18177 0 snd_pcm 80845 2 snd_hda_intel,snd_hda_codec uvcvideo 67203 0 btusb 17912 2 snd_seq_midi 13132 0 videodev 86588 1 uvcvideo bluetooth 158438 23 rfcomm,bnep,btusb psmouse 72919 0 usbhid 41906 1 hid_logitech_dj snd_rawmidi 25424 1 snd_seq_midi intel_ips 17753 0 serio_raw 13027 0 root@ghostrider:/etc/resolvconf# ping 127.0.0.1 PING 127.0.0.1 (127.0.0.1) 56(84) bytes of data. 64 bytes from 127.0.0.1: icmp_req=1 ttl=64 time=0.042 ms 64 bytes from 127.0.0.1: icmp_req=2 ttl=64 time=0.023 ms 64 bytes from 127.0.0.1: icmp_req=3 ttl=64 time=0.036 ms 64 bytes from 127.0.0.1: icmp_req=4 ttl=64 time=0.040 ms ^C --- 127.0.0.1 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 2998ms rtt min/avg/max/mdev = 0.023/0.035/0.042/0.008 ms root@ghostrider:/etc/resolvconf# ping 192.168.1.3 PING 192.168.1.3 (192.168.1.3) 56(84) bytes of data. ^C --- 192.168.1.3 ping statistics --- 19 packets transmitted, 0 received, 100% packet loss, time 18143ms root@ghostrider:/etc/resolvconf# ping 8.8.8.8 PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data. ^C --- 8.8.8.8 ping statistics --- 11 packets transmitted, 0 received, 100% packet loss, time 10079ms root@ghostrider:/etc/resolvconf# cat /etc/lsb-release; uname -a DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION="Ubuntu 12.04 LTS" Linux ghostrider 3.2.0-24-generic-pae #39-Ubuntu SMP Mon May 21 18:54:21 UTC 2012 i686 i686 i386 GNU/Linux root@ghostrider:/etc/resolvconf# lspci -nnk | grep -iA2 net 03:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR8131 Gigabit Ethernet [1969:1063] (rev c0) Subsystem: Lenovo Device [17aa:3956] Kernel driver in use: atl1c -- 04:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller [14e4:4727] (rev 01) Subsystem: Broadcom Corporation Device [14e4:0510] Kernel driver in use: wl root@ghostrider:/etc/resolvconf# lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 007: ID 0489:e00d Foxconn / Hon Hai Bus 001 Device 004: ID 1c7a:0801 LighTuning Technology Inc. Fingerprint Reader Bus 001 Device 005: ID 064e:f219 Suyin Corp. Bus 002 Device 010: ID 0424:2412 Standard Microsystems Corp. Bus 002 Device 004: ID 046d:c52b Logitech, Inc. Unifying Receiver Bus 002 Device 011: ID 0403:6010 Future Technology Devices International, Ltd FT2232C Dual USB-UART/FIFO IC root@ghostrider:/etc/resolvconf# iwconfig lo no wireless extensions. eth1 IEEE 802.11 ESSID:"PoliTekno" Mode:Managed Frequency:2.462 GHz Access Point: 00:16:E3:40:C3:E4 Bit Rate=54 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=5/5 Signal level=-52 dBm Noise level=-97 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 eth0 no wireless extensions. root@ghostrider:/etc/resolvconf# rfkill list all 0: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: no 1: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 2: ideapad_bluetooth: Bluetooth Soft blocked: no Hard blocked: no 5: hci0: Bluetooth Soft blocked: no Hard blocked: no root@ghostrider:/etc/resolvconf# lsmod Module Size Used by nls_iso8859_1 12617 0 nls_cp437 12751 0 vfat 17308 0 fat 55605 1 vfat usb_storage 39646 0 uas 17828 0 snd_hda_codec_realtek 174055 1 rfcomm 38139 12 parport_pc 32114 0 ppdev 12849 0 bnep 17830 2 joydev 17393 0 ftdi_sio 35859 1 usbserial 37173 3 ftdi_sio snd_hda_intel 32765 3 snd_hda_codec 109562 2 snd_hda_codec_realtek,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec acer_wmi 23612 0 hid_logitech_dj 18177 0 snd_pcm 80845 2 snd_hda_intel,snd_hda_codec uvcvideo 67203 0 btusb 17912 2 snd_seq_midi 13132 0 videodev 86588 1 uvcvideo bluetooth 158438 23 rfcomm,bnep,btusb psmouse 72919 0 usbhid 41906 1 hid_logitech_dj snd_rawmidi 25424 1 snd_seq_midi intel_ips 17753 0 serio_raw 13027 0 hid 77367 2 hid_logitech_dj,usbhid ideapad_laptop 17890 0 sparse_keymap 13658 2 acer_wmi,ideapad_laptop lib80211_crypt_tkip 17275 0 snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event wl 2646601 0 wmi 18744 1 acer_wmi i915 414672 3 drm_kms_helper 45466 1 i915 snd_timer 28931 2 snd_pcm,snd_seq mac_hid 13077 0 snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq lib80211 14040 2 lib80211_crypt_tkip,wl drm 197692 4 i915,drm_kms_helper i2c_algo_bit 13199 1 i915 snd 62064 15 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_se q,snd_timer,snd_seq_device video 19068 1 i915 mei 36570 0 soundcore 14635 1 snd snd_page_alloc 14108 2 snd_hda_intel,snd_pcm lp 17455 0 parport 40930 3 parport_pc,ppdev,lp atl1c 36718 0 root@ghostrider:/etc/resolvconf# nm-tool NetworkManager Tool State: connected (global) - Device: eth1 [PoliTekno] ---------------------------------------------------- Type: 802.11 WiFi Driver: wl State: connected Default: yes HW Address: AC:81:12:7F:6B:B2 Capabilities: Speed: 54 Mb/s Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points (* = current AP) CnDStudios: Infra, 00:12:BF:3F:0A:8A, Freq 2412 MHz, Rate 54 Mb/s, Strength 85 WPA AIR_TIES: Infra, 00:1C:A8:6E:84:32, Freq 2462 MHz, Rate 54 Mb/s, Strength 72 WPA2 VKSS: Infra, 00:E0:4D:01:0D:47, Freq 2452 MHz, Rate 54 Mb/s, Strength 62 WPA2 PROGEDA: Infra, 00:1A:2A:60:BF:61, Freq 2462 MHz, Rate 54 Mb/s, Strength 47 WPA MobilAtolye: Infra, 72:2B:C1:65:75:3C, Freq 2422 MHz, Rate 54 Mb/s, Strength 35 WPA WPA2 AIRTIES_WAR-141: Infra, 00:1C:A8:AB:AA:48, Freq 2422 MHz, Rate 54 Mb/s, Strength 35 WPA WPA2 tilda_biri_yeni: Infra, 54:E6:FC:B0:3C:E9, Freq 2437 MHz, Rate 0 Mb/s, Strength 34 WEP *PoliTekno: Infra, 00:16:E3:40:C3:E4, Freq 2462 MHz, Rate 54 Mb/s, Strength 100 WPA2 AIRTIES_RJY: Infra, 00:1A:2A:BD:85:16, Freq 2462 MHz, Rate 54 Mb/s, Strength 55 WEP IPv4 Settings: Address: 0.0.0.0 Prefix: 24 (255.255.255.0) Gateway: 192.168.1.1 DNS: 192.168.1.1 - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: atl1c State: unavailable Default: no HW Address: F0:DE:F1:6C:90:65 Capabilities: Carrier Detect: yes Speed: 100 Mb/s Wired Properties Carrier: off root@ghostrider:/etc/resolvconf# sudo iwlist scan lo Interface doesn't support scanning. eth1 Scan completed : Cell 01 - Address: 00:16:E3:40:C3:E4 ESSID:"PoliTekno" Mode:Managed Frequency:2.462 GHz (Channel 11) Quality:5/5 Signal level:-48 dBm Noise level:-98 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 9 Mb/s 12 Mb/s; 48 Mb/s Cell 02 - Address: 00:E0:4D:01:0D:47 ESSID:"VKSS" Mode:Managed Frequency:2.452 GHz (Channel 9) Quality:4/5 Signal level:-64 dBm Noise level:-98 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s 48 Mb/s; 54 Mb/s Cell 03 - Address: 00:1C:A8:AB:AA:48 ESSID:"AIRTIES_WAR-141" Mode:Managed Frequency:2.422 GHz (Channel 3) Quality:2/5 Signal level:-77 dBm Noise level:-95 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: Unknown: DDB20050F204104A0001101049001E007FC5100018DE7CF0D8B70223A62711C18926AC290E30303030303139631044000102103B0001031047001076B31BC241E953CB99C3872554425A28102100194169725469657320576972656C657373204E6574776F726B73102300074169723534343010240008312E322E302E31321042000F4154303939313131383030323832351054000800060050F20400011011000741697235343430100800020084103C000103 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 9 Mb/s 12 Mb/s; 48 Mb/s Cell 04 - Address: 72:2B:C1:65:75:3C ESSID:"MobilAtolye" Mode:Managed Frequency:2.422 GHz (Channel 3) Quality:2/5 Signal level:-78 dBm Noise level:-92 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : TKIP CCMP Authentication Suites (1) : PSK IE: Unknown: DDA20050F204104A0001101044000102103B00010310470010BC329E001DD811B28601722BC165753C1021001D48756177656920546563686E6F6C6F6769657320436F2E2C204C74642E1023001C48756177656920576972656C6573732041636365737320506F696E74102400065254323836301042000831323334353637381054000800060050F204000110110009487561776569415053100800020084103C000100 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : TKIP CCMP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 9 Mb/s 18 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 12 Mb/s 24 Mb/s; 48 Mb/s Cell 05 - Address: 00:12:BF:3F:0A:8A ESSID:"CnDStudios" Mode:Managed Frequency:2.412 GHz (Channel 1) Quality:5/5 Signal level:-47 dBm Noise level:-95 dBm IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : TKIP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 22 Mb/s 6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s 36 Mb/s; 48 Mb/s; 54 Mb/s Cell 06 - Address: 00:1C:A8:6E:84:32 ESSID:"AIR_TIES" Mode:Managed Frequency:2.462 GHz (Channel 11) Quality:5/5 Signal level:-56 dBm Noise level:-98 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 22 Mb/s 6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s 36 Mb/s; 48 Mb/s; 54 Mb/s Cell 07 - Address: 54:E6:FC:B0:3C:E9 ESSID:"tilda_biri_yeni" Mode:Managed Frequency:2.437 GHz (Channel 6) Quality:1/5 Signal level:-85 dBm Noise level:-99 dBm Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 12 Mb/s; 24 Mb/s; 36 Mb/s; 9 Mb/s; 18 Mb/s 48 Mb/s; 54 Mb/s Cell 08 - Address: 18:28:61:16:57:C3 ESSID:"obilet" Mode:Managed Frequency:2.437 GHz (Channel 6) Quality:1/5 Signal level:-88 dBm Noise level:-99 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 9 Mb/s 12 Mb/s; 48 Mb/s Cell 09 - Address: 00:1A:2A:60:BF:61 ESSID:"PROGEDA" Mode:Managed Frequency:2.462 GHz (Channel 11) Quality:2/5 Signal level:-75 dBm Noise level:-98 dBm IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : TKIP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 22 Mb/s 6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s 36 Mb/s; 48 Mb/s; 54 Mb/s eth0 Interface doesn't support scanning.

  Read the article

• Is it illegal to use content in such a way?

  - by MHZ

  I have a couple of questions about the legality of the content of some websites. I am currently working on two websites and I would like to make sure I am not breaking any laws, by using some content like I am... Do I need to get a license to use images from the Internet (such as google.images.com) in my site, assuming they aren't a company logo belonging to another company? If not, am I allowed to use it after I modify it with a image editing software? If content such as phone numbers, e-mail addresses, website addresses, and text from websites can be found for free online, and I gather this information for a search engine based site that I am working on and offering this information on a paid basis (similar to google, but more specialized), is something that is legal? Note: I am not 'copying' or redirecting business from anywhere, to my site. The exact opposite, the site I am working on actually helps advertise businesses and make it easier for customers to find them.

  Read the article

• Processor with higher FSB than motherboard can support.

  - by Wesley

  Hi all, Please redirect me if there is a similar question, but I have an ECS P4VXASD2+ (V5.0) motherboard, which supports a 533 MHz FSB. I want to put in a Pentium 4 3.2 GHz processor (Socket 478) with an FSB of 800 MHz. Would this be possible? Would the FSB of the processor just be limited to 533 MHz? Thanks in advance.

  Read the article

• Can I upgrade the CPU in my Lenovo 3000 N100 laptop?

  - by Pavel

  I've got an Intel Core Duo T2300 in my laptop (Lenovo 3000 N100, 0768-49G). Here is what I could find out about it: $ sudo dmidecode # dmidecode 2.11 SMBIOS 2.4 present. 42 structures occupying 1436 bytes. Table at 0x000DC010. Handle 0x0000, DMI type 0, 24 bytes BIOS Information Vendor: LENOVO Version: 61ET37WW Release Date: 06/04/07 Address: 0xE6B70 [...] Handle 0x0002, DMI type 2, 8 bytes Base Board Information Manufacturer: LENOVO Product Name: CAPELL VALLEY(NAPA) CRB [...] Handle 0x0004, DMI type 4, 35 bytes Processor Information Socket Designation: U2E1 Type: Central Processor Family: Other Manufacturer: Intel ID: E8 06 00 00 FF FB E9 BF Version: Genuine Intel(R) CPU T2300 @ 1.66GHz Voltage: 3.3 V External Clock: 166 MHz Max Speed: 2048 MHz Current Speed: 1600 MHz Status: Populated, Enabled Upgrade: ZIF Socket L1 Cache Handle: 0x0005 L2 Cache Handle: 0x0006 L3 Cache Handle: Not Provided Serial Number: Not Specified Asset Tag: Not Specified Part Number: Not Specified $ cat /proc/cpuinfo processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 14 model name : Genuine Intel(R) CPU T2300 @ 1.66GHz stepping : 8 microcode : 0x39 cpu MHz : 1000.000 cache size : 2048 KB I believe the chipset is "Mobile Intel 945GM Express", but I don't know how to verify it on a Linux system. I'm not sure about the socket, but Intel claims "Sockets Supported: PBGA479, PPGA478". Now, I'd like to upgrade to the fastest compatible CPU available, but I'm a bit lost in all the details. Can you guys help me out with a couple of questions, please? What CPUs can I choose from? (I think it's only the Core2Duo line, but it should be enough for an upgrade) Can I use a 64-bit CPU? Can I use a CPU with a higher FSB than 667 MHz? Do I have to worry about additional cooling, or is it enough to check for similar voltage/TDP values? Thank you!

  Read the article

• Processor with higher FSB than motherboard can support.

  - by Wesley

  Hi all, Please redirect me if there is a similar question, but I have an ECS P4VXASD2+ (V5.0) motherboard, which supports a 533 MHz FSB. I want to put in a Pentium 4 3.2 GHz processor (Socket 478) with an FSB of 800 MHz. Would this be possible? Would the FSB of the processor just be limited to 533 MHz? Thanks in advance.

  Read the article

• PC can't detect second RAM installed

  - by kulwinder

  I have PC with 512 MB RAM installed (motherboard manufacture MICRO STAR, chipset P4M800), pc was running very slow so I decided to upgrade the ram. I installed CPU-Z and check the ram installed on the machine, also had a look at the stick installed. 512 MB PC 3200 400 MHz DDR but my mother supports 200 MHz and it was working ok. So I bought 2GB which I checked on manual that it support upto 2 GB Ram. So I installed 2GB PC 3200 400 MHz same as the old one, I plugged in both eventhough motherboard only support upto 2 GB but system spec only shows 512 (deducts 64 MB shared vga memory) I checked on CPU-Z, it detects both, slot 1 512 MB, slot 2 2048 MB, comparing screen for both slots, both the same, volt 2.5, frequency 166 MHz and 200MHz, only difference on those is 2gb ram shows under timings table 133MHz 166 MHz and 200MHz but 512 MB shows only 166MHz and 200MHz. I checked on Google and can't seems to figure out whats wrong with it. If I only plug in 2GB. Pc doesn't boot up like ram not working.With only 512 MB plugged in seems ok. Please help.

  Read the article

• What is the difference between these Pentium Extreme Edition CPUs?

  - by Giffyguy

  The CPU in question is the Pentium Extreme Edition 955. Intel's website shows four "versions", but for the most part they all look identical. They even share the same set of ordering codes. But one of them has a substantially lower TDP, which is seemingly unexplainable - since everything else is the same. Two of them say "LGA775, Tray" and I have no idea what "Tray" means either. Also, two of them have a different SPEC code. What I need to know is: What does "LGA775, Tray" mean? Why does the one CPU have a lower TDP? And what does that mean for me? Does that mean lower maximum power consumption? Does it mean the CPU may be more stable/endurant, because of a lower heat output? Why do two of them have a different SPEC code, and what does this mean? Finally, what does PLGA775 (as opposed to LGA775) mean, and do I need to be worried about that? Information from Intel's wbsite: Intel® Pentium® Processor Extreme Edition 955 (4M Cache, 3.46 GHz, 1066 MHz FSB) with SPEC Code 1 Boxed Intel® Pentium® Processor Extreme Edition 955 4M Cache, 3.46 GHz, 1066 MHz FSB LGA775 PLGA775 B1 95 Watts BX80553955 SL94N 2 Intel® Pentium® Processor Extreme Edition 955 4M Cache, 3.46 GHz, 1066 MHz FSB LGA775, Tray PLGA775 B1 130 Watts HH80553PH0994M SL94N 3 Boxed Intel® Pentium® Processor Extreme Edition 955 4M Cache, 3.46 GHz, 1066 MHz FSB LGA775 PLGA775 B1 130 Watts BX80553955 SL8WM 4 Intel® Pentium® Processor Extreme Edition 955 4M Cache, 3.46 GHz, 1066 MHz FSB LGA775, Tray PLGA775 B1 130 Watts HH80553PH0994M SL8WM

  Read the article

• How to calculate the setting for BCLK with Core i7?

  - by Chris_45

  If default maximum memory speed is 1333MHz, and the motherboard supports up to 2200 MHz by overclocking and it is an 2x memory multiplier as for Core i7 CPUs how do you calculate what setting BCLK should be for 1600 MHz and 2133 MHz?

  Read the article

• gateway solo 9550 windows xp

  - by papa j

  can i install a celeron 04 2.8 ghz cpu i currently have intel 01 1133 mhz

  Read the article

• How to reduce virtual memory by optimising my PHP code?

  - by iCeR

  My current code (see below) uses 147MB of virtual memory! My provider has allocated 100MB by default and the process is killed once run, causing an internal error. The code is utilising curl multi and must be able to loop with more than 150 iterations whilst still minimizing the virtual memory. The code below is only set at 150 iterations and still causes the internal server error. At 90 iterations the issue does not occur. How can I adjust my code to lower the resource use / virtual memory? Thanks! <?php function udate($format, $utimestamp = null) { if ($utimestamp === null) $utimestamp = microtime(true); $timestamp = floor($utimestamp); $milliseconds = round(($utimestamp - $timestamp) * 1000); return date(preg_replace('`(?<!\\\\)u`', $milliseconds, $format), $timestamp); } $url = 'https://www.testdomain.com/'; $curl_arr = array(); $master = curl_multi_init(); for($i=0; $i<150; $i++) { $curl_arr[$i] = curl_init(); curl_setopt($curl_arr[$i], CURLOPT_URL, $url); curl_setopt($curl_arr[$i], CURLOPT_RETURNTRANSFER, 1); curl_setopt($curl_arr[$i], CURLOPT_SSL_VERIFYHOST, FALSE); curl_setopt($curl_arr[$i], CURLOPT_SSL_VERIFYPEER, FALSE); curl_multi_add_handle($master, $curl_arr[$i]); } do { curl_multi_exec($master,$running); } while($running > 0); for($i=0; $i<150; $i++) { $results = curl_multi_getcontent ($curl_arr[$i]); $results = explode("<br>", $results); echo $results[0]; echo "<br>"; echo $results[1]; echo "<br>"; echo udate('H:i:s:u'); echo "<br><br>"; usleep(100000); } ?> Processor Information Total processors: 8 Processor #1 Vendor GenuineIntel Name Intel(R) Xeon(R) CPU E5405 @ 2.00GHz Speed 1995.120 MHz Cache 6144 KB Processor #2 Vendor GenuineIntel Name Intel(R) Xeon(R) CPU E5405 @ 2.00GHz Speed 1995.120 MHz Cache 6144 KB Processor #3 Vendor GenuineIntel Name Intel(R) Xeon(R) CPU E5405 @ 2.00GHz Speed 1995.120 MHz Cache 6144 KB Processor #4 Vendor GenuineIntel Name Intel(R) Xeon(R) CPU E5405 @ 2.00GHz Speed 1995.120 MHz Cache 6144 KB Processor #5 Vendor GenuineIntel Name Intel(R) Xeon(R) CPU E5405 @ 2.00GHz Speed 1995.120 MHz Cache 6144 KB Processor #6 Vendor GenuineIntel Name Intel(R) Xeon(R) CPU E5405 @ 2.00GHz Speed 1995.120 MHz Cache 6144 KB Processor #7 Vendor GenuineIntel Name Intel(R) Xeon(R) CPU E5405 @ 2.00GHz Speed 1995.120 MHz Cache 6144 KB Processor #8 Vendor GenuineIntel Name Intel(R) Xeon(R) CPU E5405 @ 2.00GHz Speed 1995.120 MHz Cache 6144 KB Memory Information Memory for crash kernel (0x0 to 0x0) notwithin permissible range Memory: 8302344k/9175040k available (2176k kernel code, 80272k reserved, 901k data, 228k init, 7466304k highmem) System Information Linux server3.server.com 2.6.18-194.17.1.el5PAE #1 SMP Wed Sep 29 13:31:51 EDT 2010 i686 i686 i386 GNU/Linux Physical Disks SCSI device sda: 1952448512 512-byte hdwr sectors (999654 MB) sda: Write Protect is off sda: Mode Sense: 03 00 00 08 SCSI device sda: drive cache: write back SCSI device sda: 1952448512 512-byte hdwr sectors (999654 MB) sda: Write Protect is off sda: Mode Sense: 03 00 00 08 SCSI device sda: drive cache: write back sd 0:1:0:0: Attached scsi disk sda sd 4:0:0:0: Attached scsi removable disk sdb sd 0:1:0:0: Attached scsi generic sg4 type 0 sd 4:0:0:0: Attached scsi generic sg7 type 0 Current Memory Usage total used free shared buffers cached Mem: 8306672 7847384 459288 0 487912 6444548 -/+ buffers/cache: 914924 7391748 Swap: 4095992 496 4095496 Total: 12402664 7847880 4554784 Current Disk Usage Filesystem Size Used Avail Use% Mounted on /dev/mapper/VolGroup00-LogVol00 898G 307G 546G 36% / /dev/sda1 99M 19M 76M 20% /boot none 4.0G 0 4.0G 0% /dev/shm /var/tmpMnt 4.0G 1.8G 2.0G 48% /tmp

  Read the article

• Is there any difference between processor and core?

  - by Salvador

  The following two command seems to give me different information about the same hardware srs@ubuntu:~$ cat /proc/cpuinfo | grep -e processor -e cores processor : 0 cpu cores : 4 processor : 1 cpu cores : 4 processor : 2 cpu cores : 4 processor : 3 cpu cores : 4 srs@ubuntu:~$ sudo dmidecode -t processor # dmidecode 2.9 SMBIOS 2.6 present. Handle 0x0004, DMI type 4, 42 bytes Processor Information Socket Designation: LGA1155 Type: Central Processor Family: <OUT OF SPEC> Manufacturer: Intel ID: A7 06 02 00 FF FB EB BF Version: Intel(R) Core(TM) i5-2500K CPU @ 3.30GHz Voltage: 1.0 V External Clock: 100 MHz Max Speed: 3800 MHz Current Speed: 3300 MHz Status: Populated, Enabled Upgrade: Other L1 Cache Handle: 0x0005 L2 Cache Handle: 0x0006 L3 Cache Handle: 0x0007 Serial Number: To Be Filled By O.E.M. Asset Tag: To Be Filled By O.E.M. Part Number: To Be Filled By O.E.M. Core Count: 4 Core Enabled: 1 Characteristics: 64-bit capable Until today I thought I had a single processor with 4 independent cores. I also thought that within each core can be used different threads.

  Read the article

• Ubuntu 12.04 doesn't recgonize m CPU correctly

  - by Nightshaxx

  My computer is running ubuntu 12.04 (64bit), and I have a AMD Athlon(tm) X4 760K Quad Core Processor which is about 3.8ghz (and an Radeon HD 7770 GPU). Yet, when I type in cat /proc/cpuinfo - I get: processor : 0 vendor_id : AuthenticAMD cpu family : 21 model : 19 model name : AMD Athlon(tm) X4 760K Quad Core Processor stepping : 1 microcode : 0x6001119 cpu MHz : 1800.000 cache size : 2048 KB physical id : 0 siblings : 4 core id : 0 cpu cores : 2 apicid : 16 initial apicid : 0 fpu : yes fpu_exception : yes cpuid level : 13 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt pdpe1gb rdtscp lm constant_tsc rep_good nopl nonstop_tsc extd_apicid aperfmperf pni pclmulqdq monitor ssse3 fma cx16 sse4_1 sse4_2 popcnt aes xsave avx f16c lahf_lm cmp_legacy svm extapic cr8_legacy abm sse4a misalignsse 3dnowprefetch osvw ibs xop skinit wdt lwp fma4 tce nodeid_msr tbm topoext perfctr_core arat cpb hw_pstate npt lbrv svm_lock nrip_save tsc_scale vmcb_clean flushbyasid decodeassists pausefilter pfthreshold bmi1 bogomips : 7599.97 TLB size : 1536 4K pages clflush size : 64 cache_alignment : 64 address sizes : 48 bits physical, 48 bits virtual power management: ts ttp tm 100mhzsteps hwpstate cpb eff_freq_ro processor : 1 vendor_id : AuthenticAMD cpu family : 21 model : 19 model name : AMD Athlon(tm) X4 760K Quad Core Processor stepping : 1 microcode : 0x6001119 cpu MHz : 1800.000 cache size : 2048 KB physical id : 0 siblings : 4 core id : 1 cpu cores : 2 apicid : 17 initial apicid : 1 fpu : yes fpu_exception : yes cpuid level : 13 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt pdpe1gb rdtscp lm constant_tsc rep_good nopl nonstop_tsc extd_apicid aperfmperf pni pclmulqdq monitor ssse3 fma cx16 sse4_1 sse4_2 popcnt aes xsave avx f16c lahf_lm cmp_legacy svm extapic cr8_legacy abm sse4a misalignsse 3dnowprefetch osvw ibs xop skinit wdt lwp fma4 tce nodeid_msr tbm topoext perfctr_core arat cpb hw_pstate npt lbrv svm_lock nrip_save tsc_scale vmcb_clean flushbyasid decodeassists pausefilter pfthreshold bmi1 bogomips : 7599.97 TLB size : 1536 4K pages clflush size : 64 cache_alignment : 64 address sizes : 48 bits physical, 48 bits virtual power management: ts ttp tm 100mhzsteps hwpstate cpb eff_freq_ro processor : 2 vendor_id : AuthenticAMD cpu family : 21 model : 19 model name : AMD Athlon(tm) X4 760K Quad Core Processor stepping : 1 microcode : 0x6001119 cpu MHz : 1800.000 cache size : 2048 KB physical id : 0 siblings : 4 core id : 2 cpu cores : 2 apicid : 18 initial apicid : 2 fpu : yes fpu_exception : yes cpuid level : 13 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt pdpe1gb rdtscp lm constant_tsc rep_good nopl nonstop_tsc extd_apicid aperfmperf pni pclmulqdq monitor ssse3 fma cx16 sse4_1 sse4_2 popcnt aes xsave avx f16c lahf_lm cmp_legacy svm extapic cr8_legacy abm sse4a misalignsse 3dnowprefetch osvw ibs xop skinit wdt lwp fma4 tce nodeid_msr tbm topoext perfctr_core arat cpb hw_pstate npt lbrv svm_lock nrip_save tsc_scale vmcb_clean flushbyasid decodeassists pausefilter pfthreshold bmi1 bogomips : 7599.97 TLB size : 1536 4K pages clflush size : 64 cache_alignment : 64 address sizes : 48 bits physical, 48 bits virtual power management: ts ttp tm 100mhzsteps hwpstate cpb eff_freq_ro processor : 3 vendor_id : AuthenticAMD cpu family : 21 model : 19 model name : AMD Athlon(tm) X4 760K Quad Core Processor stepping : 1 microcode : 0x6001119 cpu MHz : 1800.000 cache size : 2048 KB physical id : 0 siblings : 4 core id : 3 cpu cores : 2 apicid : 19 initial apicid : 3 fpu : yes fpu_exception : yes cpuid level : 13 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt pdpe1gb rdtscp lm constant_tsc rep_good nopl nonstop_tsc extd_apicid aperfmperf pni pclmulqdq monitor ssse3 fma cx16 sse4_1 sse4_2 popcnt aes xsave avx f16c lahf_lm cmp_legacy svm extapic cr8_legacy abm sse4a misalignsse 3dnowprefetch osvw ibs xop skinit wdt lwp fma4 tce nodeid_msr tbm topoext perfctr_core arat cpb hw_pstate npt lbrv svm_lock nrip_save tsc_scale vmcb_clean flushbyasid decodeassists pausefilter pfthreshold bmi1 bogomips : 7599.97 TLB size : 1536 4K pages clflush size : 64 cache_alignment : 64 address sizes : 48 bits physical, 48 bits virtual power management: ts ttp tm 100mhzsteps hwpstate cpb eff_freq_ro The important part of all this being, cpu MHz : 1800.000 which indicates that I have only 1.8ghz of processing power, which is totally wrong. Is it something with drivers or Ubuntu?? Also, will windows recognize all of my processing power? Thanks! (NOTE: My cpu doesn't have intigrated graphics

  Read the article

• SqlCE DB occasionally freezes on one handheld, not another

  - by Michael

  I have two types of custom handhelds which are similar, but slightly different, each running the same WinForm application and a WinCE database: Type 1: WinCE 4.2, 400 mhz, 93244 kb Type 2: WinCE 5.0, 520 mhz, 84208 kb Type 1 will happily proceed through a large batch db operation (initiated) by the app, by Type 2 will consistently begin c-r-a-w-l-i-n-g (for several to many cycles) at around the 200 cycle mark. As several points it will begin running normally and then crawl again. The app does several db op's (inserts, updates and selects, no deletes). To simplify my situation, I've built a small test app which essentially does this: command_s.CommandText = "select dvr from vr where vid = 2211250"; command_u.CommandText = "update pvr set LocationID=81 where Status='OK' and vri = 27861"; while(going) { command_s.ExecuteScalar(); command_u.ExecuteNonQuery(); } and set it off running on the two units side by side. Sure enough, the slower (400 mhz) unit is outpacing the faster (520 mhz) unit (it's about 5000 cycles ahead right now) and I can see noticable pauses on the 520 mhz unit. What is causing this?

  Read the article

• GUI interfaces to ATI card behave weirdly out of the box and after updates.

  - by jdk

  My Lenovo W500 came with an ATI Mobility FireGL V5700 and both the Catalyst control center software and Vista display manager display four monitors. What's really annoying is the behaviour. My two active displays (laptop display + my external monitor) are always #s 3 and 4 respectively which doesn't make sense. This is out of the box. Additionally dragging & dropping is jumpy and displays #1 and 2 (always inactive because they don't exist to the software) are often preventing me from dragging #3 and 4 to the rightmost side. They also auto-snap to weird positions and certain sensible positions like position one directly over top of the other are not possible. The exact same annoyances are present when using the Windows Display manager too. In other words the interface is crap and I'm looking for a fix that's not wishing I had gone with nVidia instead. I've updated drivers, and Catalyst control centre. Have latest Windows and AMD/ATI updates. Any thoughts? Graphics Software Driver Packaging Version 8.563.2.1-090401a-079160C-Lenovo Provider ATI Technologies Inc. 2D Driver Version 7.01.01.849 2D Driver File Path /REGISTRY/MACHINE/SYSTEM/ControlSet001/Control/Class/{4D36E968-E325-11CE-BFC1-08002BE10318}/0001 Direct3D Version 7.14.10.0630 OpenGL Version 6.14.10.8306 Catalyst® Control Center Version 2009.0401.1328.22301 Graphics Hardware Primary Adapter Graphics Card Manufacturer Powered by ATI Graphics Chipset ATI Mobility FireGL V5700 Device ID 9591 Vendor 1002 Subsystem ID 2126 Subsystem Vendor ID 17AA Graphics Bus Capability PCI Express 2.0 Maximum Bus Setting PCI Express 2.0 x16 BIOS Version 010.088.000.021 BIOS Part Number BK-ATI VER010.088.000.021.034663 BIOS Date 2009/09/30 Memory Size 512 MB Memory Type DDR3 Core Clock in MHz 600 MHz Memory Clock in MHz 700 MHz

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >