Search Results

Search found 64 results on 3 pages for 'ndiswrapper'.

Page 2/3 | < Previous Page | 1 2 3  | Next Page >

  • Can't control connection bit rate using iwconfig with Atheros TL-WN821N (AR7010)

    - by Paul H
    I'm trying to reduce the connection bit rate on my Atheros TP-Link TL-WN821N v3 usb wifi adapter due to frequent instability issues (reported connection speed goes down to 1Mb/s and I have to physically reconnect the adapter to regain a connection). I know this is a common problem with this device, and I have tried everything I can think of to fix it, including using drivers from linux-backports; compiling and installing a custom firmware (following instructions on https://wiki.debian.org/ath9k_htc#fw-free) and (as a last resort) using ndiswrapper. When using ndiswrapper, the wifi adapter is stable and operates in g mode at 54Mb/s (whilst when using the default ath9k_htc module, the adapter connects in n mode and the bit rate fluctuates constantly). Unfortunately, with this setup I have to run my processor using only one core, since using SMP with ndiswrapper causes a kernel oops on my system. So I want to lock my bit rate to 54Mb/s (or less, if need be) for connection stability, using the ath9k_htc module. I've tried 'sudo iwconfig wlan0 rate 54M'; the command runs with no error but when I check the bit rate with 'sudo iwlist wlan0 bitrate' the command returns: wlan0 unknown bit-rate information. Current Bit Rate:78 Mb/s Any ideas? Here's some info (hopefully relevant) on my setup: Xubuntu (12.04.3) 64bit (kernel 3.2.0-55.85-generic) using Network Manager. My Router is from Virgin Media, the VMDG480. lshw -C network : *-network description: Wireless interface physical id: 1 bus info: usb@1:4 logical name: wlan0 serial: 74:ea:3a:8f:16:b6 capabilities: ethernet physical wireless configuration: broadcast=yes driver=ath9k_htc driverversion=3.2.0-55 firmware=1.3 ip=192.168.0.9 link=yes multicast=yes wireless=IEEE 802.11bgn lsusb -v: Bus 001 Device 003: ID 0cf3:7015 Atheros Communications, Inc. TP-Link TL-WN821N v3 802.11n [Atheros AR7010+AR9287] Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 255 Vendor Specific Class bDeviceSubClass 255 Vendor Specific Subclass bDeviceProtocol 255 Vendor Specific Protocol bMaxPacketSize0 64 idVendor 0x0cf3 Atheros Communications, Inc. idProduct 0x7015 TP-Link TL-WN821N v3 802.11n [Atheros AR7010+AR9287] bcdDevice 2.02 iManufacturer 16 ATHEROS iProduct 32 UB95 iSerial 48 12345 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 60 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0x80 (Bus Powered) MaxPower 500mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 6 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 0 bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x01 EP 1 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x83 EP 3 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 1 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x04 EP 4 OUT bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 1 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x05 EP 5 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x06 EP 6 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 255 Vendor Specific Class bDeviceSubClass 255 Vendor Specific Subclass bDeviceProtocol 255 Vendor Specific Protocol bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0000 (Bus Powered) iwlist wlan0 scanning: wlan0 Scan completed : Cell 01 - Address: C4:3D:C7:3A:1F:5D Channel:1 Frequency:2.412 GHz (Channel 1) Quality=37/70 Signal level=-73 dBm Encryption key:on ESSID:"my essid" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 48 Mb/s Mode:Master Extra:tsf=00000070cca77186 Extra: Last beacon: 5588ms ago IE: Unknown: 0007756E69636F726E IE: Unknown: 010882848B962430486C IE: Unknown: 030101 IE: Unknown: 2A0100 IE: Unknown: 2F0100 IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: Unknown: 32040C121860 IE: Unknown: 2D1AFC181BFFFF000000000000000000000000000000000000000000 IE: Unknown: 3D1601080400000000000000000000000000000000000000 IE: Unknown: DD7E0050F204104A0001101044000102103B00010310470010F99C335D7BAC57FB00137DFA79600220102100074E657467656172102300074E6574676561721024000631323334353610420007303030303030311054000800060050F20400011011000743473331303144100800022008103C0001011049000600372A000120 IE: Unknown: DD090010180203F02C0000 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: Unknown: DD180050F2020101800003A4000027A4000042435E0062322F00 iwconfig: lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"my essid" Mode:Managed Frequency:2.412 GHz Access Point: C4:3D:C7:3A:1F:5D Bit Rate=78 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=36/70 Signal level=-74 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0,

    Read the article

  • Wireless card unseen by lspci

    - by al-Amjad Tawfiq Isstaif
    I installed both Ubuntu 8.04 and 10.04. I tried to install the wireless card. although I succeeded in installing the driver using ndiswrapper, it tells me that the hardware is not present. When I use lspci, it doesn't list it. I have this laptop model and I think it should have the same entry about the wireless card here: http://ubuntuforums.org/showthread.php?t=1810193 Could the problem be other than hardware malfunction?

    Read the article

  • 12.04 login terminal screen only

    - by Reinere
    So I just went through driver update. The os froze so I had to hard reboot the pc. Now I just get the login promt in terminal. so i try to run startx. codeError: API mismatch: the NVIDIA kernel module has version 304.43 but this NVIDIA driver Component has version 295.49| i just got this error... I have to type sudo su then modprobe ndiswrapper to get my wifi to work, so step by step instructions after that would be greatly helpful

    Read the article

  • How to get GUI back after freeze interrupted an Nvidia driver update?

    - by Reinere
    I just went through a driver update. The OS froze, so I had to hard reboot the PC. Now I just get the login prompt in terminal. So, I tried to run startx. codeError: API mismatch: the NVIDIA kernel module has version 304.43 but this NVIDIA driver Component has version 295.49` I just got this error. I have to type sudo su then modprobe ndiswrapper to get my Wi-Fi to work, so step by step instructions after that would be greatly helpful.

    Read the article

  • How do I install Inventel UR056g usb wifi?

    - by kuberprok
    I am am using a Inventel UR054g (R01) usb wireless adaptor on my desktop. I had quite trouble setting it up but after installing ndiswrapper and prism2 drivers I got it up and running. However, I need to run in the command line the following to get it started; sudo dhcpcd wlan0 I want this top start automatically when I restart the PC. Further, I aslo want this connection to be available to other users. Any help would be appreciated.

    Read the article

  • Configuring WPA WiFi in Ubuntu 10.10

    - by sma
    I am trying to configure my wireless network on my laptop running Ubuntu 10.10 and am having a bit of difficulty. I am a complete Linux newb, but want to learn it, hence the reason I'm trying to set this up. Here's the vitals: It is a Gateway 600 YG2 laptop. It was previously running Windows XP, but I installed Ubuntu 10.10 in place of it (not a dual boot, I removed XP altogether). I have an old wireless card that I'm trying to resurrect. I haven't really used the card in a couple years, but it seems to still work, I just can't connect to my home's wireless network. The card is a Linksys WPC11 v2.5. When I plug it in, Ubuntu recognizes the network, but won't connect to it. My home network uses WPA encryption and the only connection type that Ubuntu's network manager is giving me is WEP and then it asks for a key -- I have no idea what that key should be. So, basically, I'm asking, is there a way I can instead connect through WPA? I've tried creating a new connection in network manager, but that won't work, it keeps falling back to the WEP connection and asking me for a key. I have tried to install the XP driver using ndiswrapper but I don't know if that's working or not. Is there a way to tell if: A) the card is working as it should B) the correct drivers are installed (again, I installed the XP one using ndiswrapper NET8180.INF, but I'm not sure what to do next) Any help would be appreciated. Thank you.

    Read the article

  • Configuring WPA WiFi in Ubuntu 10.10

    - by sma
    Hello, I am trying to configure my wireless network on my laptop running Ubuntu 10.10 and am having a bit of difficulty. I am a complete Linux newb, but want to learn it, hence the reason I'm trying to set this up. Here's the vitals: It is a Gateway 600 YG2 laptop. It was previously running Windows XP, but I installed Ubuntu 10.10 in place of it (not a dual boot, I removed XP altogether). I have an old wireless card that I'm trying to resurrect. I haven't really used the card in a couple years, but it seems to still work, I just can't connect to my home's wireless network. The card is a Linksys WPC11 v2.5. When I plug it in, Ubuntu recognizes the network, but won't connect to it. My home network uses WPA encryption and the only connection type that Ubuntu's network manager is giving me is WEP and then it asks for a key -- I have no idea what that key should be. So, basically, I'm asking, is there a way I can instead connect through WPA? I've tried creating a new connection in network manager, but that won't work, it keeps falling back to the WEP connection and asking me for a key. I have tried to install the XP driver using ndiswrapper but I don't know if that's working or not. Is there a way to tell if: A) the card is working as it should B) the correct drivers are installed (again, I installed the XP one using ndiswrapper NET8180.INF, but I'm not sure what to do next) Any help would be appreciated. Thank you.

    Read the article

  • Configuring WPA WiFi in Ubuntu 10.10

    - by sma
    Hello, I am trying to configure my wireless network on my laptop running Ubuntu 10.10 and am having a bit of difficulty. I am a complete Linux newb, but want to learn it, hence the reason I'm trying to set this up. Here's the vitals: It is a Gateway 600 YG2 laptop. It was previously running Windows XP, but I installed Ubuntu 10.10 in place of it (not a dual boot, I removed XP altogether). I have an old wireless card that I'm trying to resurrect. I haven't really used the card in a couple years, but it seems to still work, I just can't connect to my home's wireless network. The card is a Linksys WPC11 v2.5. When I plug it in, Ubuntu recognizes the network, but won't connect to it. My home network uses WPA encryption and the only connection type that Ubuntu's network manager is giving me is WEP and then it asks for a key -- I have no idea what that key should be. So, basically, I'm asking, is there a way I can instead connect through WPA? I've tried creating a new connection in network manager, but that won't work, it keeps falling back to the WEP connection and asking me for a key. I have tried to install the XP driver using ndiswrapper but I don't know if that's working or not. Is there a way to tell if: A) the card is working as it should B) the correct drivers are installed (again, I installed the XP one using ndiswrapper NET8180.INF, but I'm not sure what to do next) Any help would be appreciated. Thank you.

    Read the article

  • Ubuntu and Belkin N150 f6d4050 Wireless USB adapter v2

    - by Andrew
    I'm new to Ubuntu, and I'm trying to get my Belkin USB adapter to work. There are plenty of discussions out there already about this, but none really helped me out. Here's what I've done - Installed ndiswrapper Installed ndisgtk Installed the driver (rt2870.inf) via ndisgtk ndisgtk reported that the driver was installed and the hardware was present. The green light on the adapter is solid green, which I assume means that Ubuntu is aware of it's presence. However, when I click the little wireless symbol at the navigation bar, there's no option to choose my adapter (assuming that it's supposed to show up there...) My adapter version is F6D4050 - Where do I go from here? I'm a Ubuntu newb, so speak slowly. :P lsusb - andrew@ubuntu:~$ lsusb Bus 002 Device 003: ID 046d:c517 Logitech, Inc. LX710 Cordless Desktop Laser Bus 002 Device 002: ID 04f9:0229 Brother Industries, Ltd Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 004: ID 050d:935b Belkin Components Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub lsmod - andrew@ubuntu:~$ lsmod Module Size Used by binfmt_misc 7960 1 fbcon 39270 71 tileblit 2487 1 fbcon font 8053 1 fbcon bitblit 5811 1 fbcon softcursor 1565 1 bitblit vga16fb 12757 0 vgastate 9857 1 vga16fb snd_cmipci 37557 2 snd_intel8x0 31155 2 snd_ac97_codec 125394 1 snd_intel8x0 ac97_bus 1450 1 snd_ac97_codec snd_mpu401 6875 0 snd_pcm_oss 41394 0 snd_mixer_oss 16299 1 snd_pcm_oss snd_pcm 87882 4 snd_cmipci,snd_intel8x0,snd_ac97_codec,snd_pcm_oss snd_opl3_lib 10846 1 snd_cmipci snd_hwdep 6924 1 snd_opl3_lib snd_mpu401_uart 6857 2 snd_cmipci,snd_mpu401 snd_seq_dummy 1782 0 snd_seq_oss 31219 0 snd_seq_midi 5829 0 snd_rawmidi 23420 2 snd_mpu401_uart,snd_seq_midi snd_seq_midi_event 7267 2 snd_seq_oss,snd_seq_midi snd_seq 57481 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event nouveau 515227 2 ttm 60847 1 nouveau snd_timer 23649 3 snd_pcm,snd_opl3_lib,snd_seq snd_seq_device 6888 6 snd_opl3_lib,snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq ns558 3704 0 ppdev 6375 0 drm_kms_helper 30742 1 nouveau joydev 11072 0 ndiswrapper 244768 0 gameport 10966 3 snd_cmipci,ns558 usblp 12407 0 asus_atk0110 10033 0 parport_pc 29958 1 serio_raw 4918 0 drm 199204 4 nouveau,ttm,drm_kms_helper i2c_algo_bit 6024 1 nouveau edac_core 45423 0 edac_mce_amd 9278 0 k8temp 3912 0 snd 71106 23 snd_cmipci,snd_intel8x0,snd_ac97_codec,snd_mpu401,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_opl3_lib,snd_hwdep,snd_mpu401_u art,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 8052 1 snd snd_page_alloc 8500 2 snd_intel8x0,snd_pcm i2c_nforce2 6099 0 lp 9336 0 parport 37160 3 ppdev,parport_pc,lp hid_logitech 8820 0 ff_memless 5109 1 hid_logitech ohci1394 30260 0 usbhid 41084 1 hid_logitech hid 83440 2 hid_logitech,usbhid usb_storage 49833 0 skge 41049 0 ieee1394 94771 1 ohci1394 sata_sil 8895 0 forcedeth 55592 0 sata_nv 23778 1 pata_amd 11962 1 floppy 63156 0

    Read the article

  • Need Drivers for D-link DWA 525 PCI Wireless adapter

    - by Hari
    I'm using Ubuntu 12.10 32-Bit Edition. I have racently purchased D-link DWA 525 PCI Wireless Adapter. But i can't find the drivers for the adapter. I have been searching in internet for a while. Tried many options, including ndiswrapper. When i run lspci command, it detects and shows as below. 04:00.0 Network controller: Ralink corp. RT5360 Wireless 802.11n 1T/1R My kernel version is 3.5.0-18-generic. Please help me out.

    Read the article

  • Macbook Pro 8,1 - wireless interface not showing up

    - by Florian Margaine
    I've installed Ubuntu 11.10 on my Macbook Pro 8,1. Everything went fine and everything installs fine except for the wireless interface. I've installed the b43 module according to these instructions: https://help.ubuntu.com/community/MacBookPro8-1/Natty#Wireless I've tried compiling the module, ndiswrapper and also the last solution mentioned using this PPA: ppa:zwaldowski/ppa. With the three solutions, the module loads finely. It works smoothly. lspci shows the wireless card without problem. But there is no wireless interface. iwconfig or ifconfig both show eth0 and lo as interfaces, but no eth1 or wlan0 interface is showing up. I have no idea why, and I'm completely stuck there.

    Read the article

  • I have a problem with a AE1200 Cisco/Linksys Wireless-N USB adapter having stopped working after I ran the update manager in Ubuntu 12.04

    - by user69670
    Here is the problem, I use a Cisco/Linksys AE1200 wireless network adapter to connect my desktop to a public wifi internet connection. I use ndiswrapper to use the windows driver and it had been working fine for me untill I ran the update manager overnight a few days ago. When I woke up it was asking for the normal computer restart to implement the changes but after rebooting the computer, the wireless adapter did not work, the status light on the adapter did not light up even though ubuntu recognizes it is there and according to ndiswrapper the drivers are loaded and the hardware is present. the grep command is being a bitch for some unknown reason today so this will be long sorry Output from "lspci": 00:00.0 Host bridge: Advanced Micro Devices [AMD] nee ATI Radeon Xpress 200 Host Bridge (rev 01) 00:01.0 PCI bridge: Advanced Micro Devices [AMD] nee ATI RS480 PCI Bridge 00:12.0 SATA controller: Advanced Micro Devices [AMD] nee ATI SB600 Non-Raid-5 SATA 00:13.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI0) 00:13.1 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI1) 00:13.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI2) 00:13.3 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI3) 00:13.4 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB (OHCI4) 00:13.5 USB controller: Advanced Micro Devices [AMD] nee ATI SB600 USB Controller (EHCI) 00:14.0 SMBus: Advanced Micro Devices [AMD] nee ATI SBx00 SMBus Controller (rev 13) 00:14.1 IDE interface: Advanced Micro Devices [AMD] nee ATI SB600 IDE 00:14.3 ISA bridge: Advanced Micro Devices [AMD] nee ATI SB600 PCI to LPC Bridge 00:14.4 PCI bridge: Advanced Micro Devices [AMD] nee ATI SBx00 PCI to PCI Bridge 01:05.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI RC410 [Radeon Xpress 200] 02:02.0 Communication controller: Conexant Systems, Inc. HSF 56k Data/Fax Modem 02:03.0 Multimedia audio controller: Creative Labs CA0106 Soundblaster 02:05.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Output from "lsusb": Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 009: ID 13b1:0039 Linksys AE1200 802.11bgn Wireless Adapter [Broadcom BCM43235] Bus 003 Device 002: ID 045e:0053 Microsoft Corp. Optical Mouse Bus 004 Device 002: ID 1043:8006 iCreate Technologies Corp. Flash Disk 32-256 MB Output from "ifconfig": eth0 Link encap:Ethernet HWaddr 00:19:21:b6:af:7c UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:20 Base address:0xb400 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:13232 errors:0 dropped:0 overruns:0 frame:0 TX packets:13232 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1084624 (1.0 MB) TX bytes:1084624 (1.0 MB) Output from "iwconfig": lo no wireless extensions. eth0 no wireless extensions. Output from "lsmod": Module Size Used by nls_iso8859_1 12617 1 nls_cp437 12751 1 vfat 17308 1 fat 55605 1 vfat uas 17828 0 usb_storage 39646 1 nls_utf8 12493 1 udf 84366 1 crc_itu_t 12627 1 udf snd_ca0106 39279 2 snd_ac97_codec 106082 1 snd_ca0106 ac97_bus 12642 1 snd_ac97_codec snd_pcm 80845 2 snd_ca0106,snd_ac97_codec rfcomm 38139 0 snd_seq_midi 13132 0 snd_rawmidi 25424 2 snd_ca0106,snd_seq_midi bnep 17830 2 parport_pc 32114 0 bluetooth 158438 10 rfcomm,bnep ppdev 12849 0 snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event snd_timer 28931 2 snd_pcm,snd_seq snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq snd 62064 11 snd_ca0106, snd_ac97_codec,snd_pcm,snd_rawj9fe snd_ca0106,snd_ac97_codec,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 14635 1 snd snd_page_alloc 14108 2 snd_ca0106,snd_pcm sp5100_tco 13495 0 i2c_piix4 13093 0 radeon 733693 3 ttm 65344 1 radeon drm_kms_helper 45466 1 radeon drm 197692 5 radeon,ttm,drm_kms_helper i2c_algo_bit 13199 1 radeon mac_hid 13077 0 shpchp 32325 0 ati_agp 13242 0 lp 17455 0 parport 40930 3 parport_pc,ppdev,lp usbhid 41906 0 hid 77367 1 usbhid 8139too 23283 0 8139cp 26759 0 pata_atiixp 12999 1 Output from "sudo lshw -C network": *-network description: Ethernet interface product: RTL-8139/8139C/8139C+ vendor: Realtek Semiconductor Co., Ltd. physical id: 5 bus info: pci@0000:02:05.0 logical name: eth0 version: 10 serial: 00:19:21:b6:af:7c size: 10Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 10 0bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=8139too driverversion=0.9.28 duplex=half latency=64 link=no maxlatency=64 mingnt=32 multicast=yes port=MII speed=10Mbit/s resources: irq:20 ioport:b400(size=256) memory:ff5fdc00-ff5fdcff Output from "iwlist scan": lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. Output from "lsb_release -d": Ubuntu 12.04 LTS Output from "uname -mr": 3.2.0-24-generic-pae i686 Output from "sudo /etc/init.d/networking restart": * Running /etc/init.d/networking restart is deprecated because it may not enable again some interfaces * Reconfiguring network interfaces... [ OK ]

    Read the article

  • How did Ubuntu know my WPA Key?

    - by nebukadnezzar
    I've recently moved my /home to another computer (keeping all configuration files), with a fresh installation of Ubuntu 10.10. After Installation I've installed wicd and ndiswrapper, to get my Internet Connection up and running. However, after changing /etc/network/interfaces from auto lo iface lo inet loopback To auto wlan0 iface wlan0 inet dhcp and running sudo /etc/init.d/networking restart to get wlan0 set up, wicd just suddenly connected... to my modem. Without supplying any information about the modem whatsoever. Of course wicd creates a local directory at ~/.wicd/, but that directory is empty, and the temporary global configuration at /var/lib/wicd/configurations/ didn't exist due to fresh installation of ubuntu. So what's the deal? Where did wicd get the ESSID and the WPA Key? There hasn't been any activity in this question, but it's still open (and even worth some rep)!

    Read the article

  • Cannot connect to a Wifi network chipset AR9287

    - by Fritz
    After updating my newly installed ubuntu 10.10. I can't connect to the wifi network anymore although it is showing it. Tried to install manufacturer driver INF file via ndiswrapper only makes things worst - lost my wifi. Downloaded and installed the compat-wireless driver for the Atheros AR9287. After installing, i got my wifi connection again but after rebooting I can't reconnect again. The Wifi access point is showing 2/5 to 3/5 signal strength. Laptop: Acer Aspire 4741G Wifi Adapter: Atheros AR9287 OS: Ubuntu 10.10 64bit

    Read the article

  • Netgear WNA1100 stopped working

    - by NOLFXceptMe
    I'm facing a rather strange issue with the USB wireless adapter WNA1100. I was able to connect to wireless using this yesterday. However, today am not. lsmod shows ath9k_htc, ath9k_common, ath9k_hw, ath and ndiswrapper. I'm not sure if this is relevant to the above problem, but between yesterday and today, the only change was an upgrade to Ubuntu 2.6.38 kernel, which caused the NVIDIA driver to break (I have a 7300GT), so I had to ignore that kernel, reboot into 2.6.35, and rebuild NVIDIA module from NVIDIA-Installer-270.run. Help?

    Read the article

  • Ubuntu 12.04 LTS Realtek RTL8192E Problems

    - by Logan
    My wifi is not working. I have tried ndiswrapper with the XP driver but that still did not work. Please explain to me in layman's terms. I can run commands so if you tell me exactly what to put, i will put it. Basically, ubuntu is not showing a wireless networks option and when I ran some command yesterday it said the driver was UNCLAIMED. Please help. This is a wintec card with realtek rtl8192E chip on it. It is a desktop computer. On a 20gb partition, other 60gb is for windows(yeah its an old desktop). Use windows installer to install ubuntu(this is one of the dell desktops that wont boot ubuntu from disk). So any help is appreciated and I would like to get this done THIS weekend.

    Read the article

  • If Ubuntu freezes when running off a USB drive, will it freeze after full installation?

    - by fearoffours
    I'm planning to install Ubuntu on an aging Compaq Presario V5000. I've established that the Unity desktop is not suited to this laptop, and am now using the standard (Gnome?) desktop. I'm grappling with ndiswrapper and my wireless chipset. But I'm still running it off a USB drive before I take the plunge and install properly to my internal HD. Part of my reticence in completing the installation is I'm experience freezes after about 10-20 minutes usage. Is this likely to be in any way related to running it off the USB drive?

    Read the article

  • Cisco Linksys AE2500 wireless adapter not working

    - by makuto
    I have a Cisco AE2500 I've used with my laptop to get internet. I had to install the drivers by following this forum: http://ubuntuforums.org/showthread.php?t=1805830 But now the blue light on the adapter doesn't turn on at all, but ndiswrapper reports it is connected. I have no connection to the internet on my laptop, and the adapter doesn't show it's blue light on any of the USB ports of my computer or on the 4 port hub I have. Is there some way I can reset something so that the blue light will show again? I'm using Ubuntu 11.10 on a Dell Latitude D505 laptop. EDIT: I deleted and reinstalled the same exact driver and everything worked again.

    Read the article

  • Ubuntu 12.04 and Realtek Wireless Card Incompatible

    - by Tim
    Quick background: I installed Linux Ubuntu 12.04 on a Dell Inspiron 3520 after uninstalling Windows 8. A friend suggested to do this as opposed to buying a laptop with Linux pre-installed. Everything except the wireless card works. When I load up the laptop, I see a wireless animation as if it's trying to locate the wireless connection (for a while, then it goes blank), but no connections appear under the wireless option (under "Edit Connections" then "Wireless"). What I've tried: - Doing ndiswrapper. Failed. - Installing a few kernels for realtek. Failed.

    Read the article

  • How do I get a Realtek Wireless USB Airlink101 AWLL5088 working?

    - by Tobias_Mann
    I am running Ubuntu 11.10, 32bit. I ordered them a Realtek Airlink101 AWLL5088 based upon the relative ease for linux installation. I am having trouble installing the drivers. I copied the drivers to /usr/src/ and ran sudo ./install.sh from that director listed above. I have tried ndiswrapper, and allowing the default drivers, but with no luck. It seems to continue to try and use the default free drivers, even though I have blacklisted them using the guide described here. There was no error, I was asked which card I was using. I looked at the packaging and at the support page, and guessed number 2, allowed to finish, and rebooted. It continued detect the wireless network after the reboot, but would never complete the connection. I would appreciate any feedback. I am kind of stuck trying to figure this out.

    Read the article

  • Configure Wireless Network Card

    - by Skizz
    I recently upgraded the wireless network card in my Ubuntu PC from an 802.11g to an 802.11n. Now, it can't see my router. It doesn't appear in the list of networks that is displayed when you click on the NetworkManager icon in Gnome. Other networks are listed and I have connected to them (no password required!). I'm using the Windows driver through ndiswrapper and it can see the card. I tested the card in a Windows PC and everything worked. The router's log doesn't show any messages coming from the wireless card. What have I done wrong? If you need any more information, just leave a comment and I'll get add it to the question.

    Read the article

  • How to Install a Wireless Card in Linux Using Windows Drivers

    - by Justin Garrison
    Linux has come a long way with hardware support, but if you have a wireless card that still does not have native Linux drivers you might be able to get the card working with a Windows driver and ndiswrapper. Using a Windows driver inside of Linux may also give you faster transfer rates or better encryption support depending on your wireless card. If your wireless card is working, it is not recommended to install the Windows driver just for fun because it could cause a conflict with the native Linux driver Latest Features How-To Geek ETC How To Make Hundreds of Complex Photo Edits in Seconds With Photoshop Actions How to Enable User-Specific Wireless Networks in Windows 7 How to Use Google Chrome as Your Default PDF Reader (the Easy Way) How To Remove People and Objects From Photographs In Photoshop Ask How-To Geek: How Can I Monitor My Bandwidth Usage? Internet Explorer 9 RC Now Available: Here’s the Most Interesting New Stuff Smart Taskbar Is a Thumb Friendly Android Task Launcher Comix is an Awesome Comics Archive Viewer for Linux Get the MakeUseOf eBook Guide to Speeding Up Windows for Free Need Tech Support? Call the Star Wars Help Desk! [Video Classic] Reclaim Vertical UI Space by Adding a Toolbar to the Left or Right Side of Firefox Androidify Turns You into an Android-style Avatar

    Read the article

  • Broadcom 4312 wireless not working on an HP dv6-1245 DX

    - by vitalie
    I have installed Ubuntu 10.04 on my HP dv6-1245 dx notebook and I do not have any wifi (it worked perfectly in windows vista and 7). I have followed a lot of instructions found on net but still not able to get Internet. Here is the outcome of lspci: $ sudo lspci 00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07) 00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) 00:02.1 Display controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) 00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) 00:1a.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) 00:1a.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03) 00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 (rev 03) 00:1c.3 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 4 (rev 03) 00:1c.4 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 (rev 03) 00:1c.5 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 (rev 03) 00:1d.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) 00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.3 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) 00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation ICH9M/M-E SATA AHCI Controller (rev 03) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03) 00:1f.6 Signal processing controller: Intel Corporation 82801I (ICH9 Family) Thermal Subsystem (rev 03) 02:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01) 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 02) I have used ndiswrapper and have installed it, as well as the windows drivers for Broadcom, no change.

    Read the article

  • How to get Broadcom BCM 43XX Wireless card working

    - by Fer1805
    NOTE - Although this question is for a specific version of Ubuntu and a specific Broadcom model, the answer to it is for most Broadcom models and versions of Ubuntu 11.04, 11.10, 12.04 and 12.10. If you have come here from another question, feel free to read the answer instead. The answer covers many problems with several solutions. I'm having serious problems installing the Broadcom drivers for Ubuntu 11.04. It worked perfectly on my previous version, but now, it is impossible. I'm a user with no advance knowledge in Linux, so I would need clear explanations on make, compile, etc. I was following the instructions on the following blog, with no luck. How can I get Broadcom BCM4311 Wireless working? Can someone help me? Edit: For the command: "lspci | grep Network", I get the following message: 06:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01) For the command: iwconfig, i get the following: lo no wireless extensions. eth0 no wireless extensions. When i follow the following steps (from the above link), there are a NO error message at all: open the 'Synaptic Package Manager' and search for bcm uninstall the bcm-kernel-source package make sure that the firmware-b43-installer and the b43-fwcutter packages are installed type into terminal: cat /etc/modprobe.d/* | egrep '8180|acx|at76|ath|b43|bcm|CX|eth|ipw|irmware|isl|lbtf|orinoco|ndiswrapper|NPE|p54|prism|rtl|rt2|rt3|rt6|rt7|witch|wl' (you may want to copy this) and see if the term blacklist bcm43xx is there if it is, type cd /etc/modprobe.d/ and then sudo gedit blacklist.conf put a # in front of the line: blacklist bcm43xx then save the file (I was getting error messages in the terminal about not being able to save, but it actually did save properly). reboot 'End of procedure' Before (not ubuntu 11.04), if i wanted to connect wireles, i just went to the icon at the upper side of the screen, click, showed ALL the wireless network available, and done. Now, the only options i see are: Wired Network Auto Eth0 Disconnect VPN Enable networking Connection information Edit connection. hope above info is enough for your help.

    Read the article

  • How do I install windows wireless driver for TP-Link TL-WN7200ND

    - by Jim
    I'm using the TP-Link TL-WN7200ND USB wireless adapter. I have downloaded the Windows drivers and updated Ubuntu to 10.10 by manually connecting the computer to the router. I also installed ndiswrapper-gtk. I get a Windows Wireless Drivers in my Administration menu, and I was able to get it to read the Windows 7 .inf file. The .inf for XP does not work. It adds it and the driver appears in the list with "Hardware: present". I set up the wireless connection information (ESSID and WPA2-Personal key). Problem: I don't see the network manager icon in the top right of the screen. I managed to manually start it manually using sudo services network-manager restart but it shows no connections in the menu, saying that there's nothing to manage. In my /etc/network/interfaces file I have an entry for the loopback and the standard two-liner for eth0 with dhcp. From memory, something like: iface eth0 auto eth0 dhcp I had read somewhere that 10.10 would have standard support for my wireless adapter (TL-WN7200ND) but that seems not to be the case. However, I don't ever remember having the network-manager icon in the top-right and it does not auto-start at the moment. This was originally an Ubuntu 9.10 install that I've upgraded over time. I also used to use pppoeconf to connect to the net, which might affect the /etc/network/interfaces file?

    Read the article

< Previous Page | 1 2 3  | Next Page >