Search Results

Search found 338 results on 14 pages for 'netgear'.

Page 2/14 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• Netgear FVX538v2 slow whene connected to Canoga Perkins N525 ETSU

  - by Doomloard

  First of all thank you in advance for helping me. my issue is the old network admin found a problem whene he connected the firewall and the ETSU together the through put went down to less than 1 mega bit a second. his fix was to add a dlink router between the firewall and the etsu which speed it up to 5 mega bits a second. now my boss wants a more clean and proper solution if possible. i have check all the settings in the netgear it dose not seem to be a setting issue. if anyone can help that would be great.

  Read the article

• 2 x Netgear GS724T (Dual GBIC) trunking issue

  - by Arthor

  I have the following: Netgear GS724T (Firmware Version V1.0.3_35, Protocol Version - 2.001.002) 4 x Indineon ISFP GBR/FC Settings STP Function - Enabled Fast Link - Enabled Trunking port 23,24, (21,22 - RJ45 cables, but not connected.) I have connected both switches via 2 fiber cables and want to use trunking. The problem I am having. Sometimes I get a an issue when none of the switches cannot talk with each other, nor the devices, sometime they can. The problem is irregular and no patten can be determined The statistics shows that when the switches does not work, they have RX errors If I remove one to the GBIC connections, then everything works as normal.] Question Does anyone have a solution for this please? Thanks

  Read the article

• Netgear router-speed problem after XBox use

  - by John Dudley

  When my son is at my place at the weekend, he plays XBox Live over the internet, using my wireless network (Netgear 'g' type router). This usually thrashes & crashes the router to the extent I have to hard-boot it to get it working again. However, after this weekend, on my two laptops, I'm left with the problem that the router is working, but I'm only getting 0.38Mbps out of it, at all times of the day. I've tried hard-booting the router, but no difference. Could this be a knock-on effect of the Xbox use? I can't believe the router could be damaged, but working slower? Is that possible? Tiscali haven't come back to me yet on any 'network' issues. Thanks in advance

  Read the article

• Netgear WNR1000 WiFi speed

  - by Kamil Klimek

  I have Netgear WNR1000 150N, Macbook Pro 13" with Broadcom BCM43xx 1.0, Network connection 60mbps When I connect through the cable I easily get around 60mbps. When I go through the WiFi it's capable to get only 32mbps at tops. Any ideas why is that? Is that my router limitation or maybe my WiFi card? If it is routers fault what router would you suggest. Best router would be with usb port for external hard drive. Forgot to add screenshot with connection details: Szybkosc transmisji == Transmission speed

  Read the article

• Set Up Port-Forwarding on Netgear N300 Router

  - by Smitty

  I have a Netgear N300 router that has DynDNS.org as a preset DDNS option. After setting it up it (unsurprisingly) sent traffic directly to my router. I'm essentially using this to connect remotely to my home (virtual) machine/s. From what I've read, it seems like I need to set up port forwarding. I tried forwarding "all" inbound traffic to a specific IP but that just didn't work. What am I doing wrong? Also, I just noticed I get this error after applying the settings: "The specified port(s) are being used by other configurations. Please check your configurations of Remote Management, Port forwarding, Port Triggering, UPnP Port Mapping table, RIP, and Internet connection type"

  Read the article

• Netgear WNDR3700 2.4GHz and 5GHz Wi-Fi are segregated

  - by Tim Sullivan

  I have a Netgear WNDR3700 with both the 2.4GHz (B/G/N) and 5GHz (A/N) broadcasting. I'd assumed that devices connecting on either channel would work together without issues, but there are some devices (such as my iPhone 4 or HP wireless printer) that will only connect at 2.4GHz, and some that connect at 5GHz. However, it seems that they're segregated on the network, so a computer at 5GHz can't print to the printer, but the iPhone can. This is causing issues not just with printing, but with AppleTV and so on. Is there a way to have the router let these devices all talk to each other?

  Read the article

• Netgear router keeps disconnecting iPhone

  - by DisgruntledGoat

  My old router (Voyager 2091) packed up so I just got a new router - a Netgear N150 model DGN1000. My laptop connects OK wirelessly, but my iPhone 4S is constantly getting "disconnected" - it has perfect wifi signal and is seemingly connected to the router, but no pages load (it says "server cannot be found"). If I disconnect manually ("forget this network") then reconnect, it works fine again for a random amount of time (usually 10-30 minutes) then I get the same problem again. I've done some searching and this appears to be a known problem - there are dozens of forum posts out there lamenting similar connection problems. The only advice I have seen is to set a specific channel under Wireless Settings on the router CP, although every forum post recommends a different channel! 1, 3, 5, 6, 11... I have tried them all for hours at a time and get the exact same problem. The firmware is up to date. Is there an actual solution for this, or do I need to get a different router just to be able to use my iPhone?

  Read the article

• Configure vlan on Netgear switch via SNMP

  - by Russell Gallop

  I am trying to configure vlans on a netgear GS752TSX from the Linux command line with netsnmp. I have created vlan 99 on the web interface now want to control the pvid settings, egress and tagging. I have identified these as the MIBs I need to change: dot1qPvid.<port> dot1qVlanStaticEgressPorts.99 dot1qVlanStaticUntaggedPorts.99 Pvid works as I expect: $ snmpset -r 1 -t 20 -v 2c -c private <switch> dot1qPvid.17 u 99 Q-BRIDGE-MIB::dot1qPvid.17 = Gauge32: 99 $ snmpget -r 1 -t 20 -v 2c -c private <switch> dot1qPvid.17 Q-BRIDGE-MIB::dot1qPvid.17 = Gauge32: 99 and so do the egress ports: $ snmpset -r 1 -t 20 -v 2c -c private <switch> dot1qVlanStaticEgressPorts.99 x 'ff ff ff ff ff ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00' Q-BRIDGE-MIB::dot1qVlanStaticEgressPorts.99 = Hex-STRING: FF FF FF FF FF FF 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 $ snmpget -r 1 -t 20 -v 2c -c private <switch> dot1qVlanStaticEgressPorts.99 Q-BRIDGE-MIB::dot1qVlanStaticEgressPorts.99 = Hex-STRING: FF FF FF FF FF FF 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 But untagging the ports doesn't seem to remember my setting: $ snmpset -r 1 -t 20 -v 2c -c private <switch> dot1qVlanStaticUntaggedPorts.99 x 'ff ff ff ff ff ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00' Q-BRIDGE-MIB::dot1qVlanStaticUntaggedPorts.99 = Hex-STRING: FF FF FF FF FF FF 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 $ snmpget -r 1 -t 20 -v 2c -c private <switch> dot1qVlanStaticUntaggedPorts.99 Q-BRIDGE-MIB::dot1qVlanStaticUntaggedPorts.99 = Hex-STRING: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 I have tried netsnmp 5.4.1 and 5.7.2. Is there something I'm doing wrong?

  Read the article

• Reserving an IP with Netgear router from Time Warner

  - by Sergio Oliveira Jr.

  I tried everything but keep getting the following error: "Duplicated MAC address". Nothing is duplicated. I disconnected the PC that I would like to assign the IP. Basically this is important as I will configure some port forwarding and my notebook must always get the same IP from DHCP. This is called DHCP reservation but apparently is not working on this router. Has anyone being luck to have this working? The model is CG814WG and you have to click on LAN IP under web administration, -Sergio

  Read the article

• Question about Remote WAN IP on NetGear FVS336G VPN setup

  - by camilian

  I wanted to be able to have a VPN connection to my home network so I purchased the FVS336G because the reviews said it was easy set up. I am sure it is for someone that knows what needs to be entered it is easy, but I am a little confused. Using the VPN wizard I choose VPN Client as the tunnel connection, enter key, etc... but then I get to the "What is the remote WAN's IP or Internet Name" and "What is the local WAN's IP address or Internet Name" I am lost. I am probably being really dumb, but I am not sure what I need to put in here. Is the remote WAN ip the ip from the outside world to my cable modem? Is the local ip the ip to my FVS336G? Any help would be appreciated.

  Read the article

• Netgear CG3000D new Modem/Router - Random High Ping

  - by justin.chmura

  Cox just recently came out and looked at my internet and decided that the modem I had was causing high latency issue. The speed was fine but the ping would spike to around 100 and over when gaming or putting a load more than browsing on the line. After they replaced it, it seems like I get better latency, but when it spikes, I get upwards of over 300 ping with like 500 jitter. I figured I would hit the serverfault universe before sending another email to Cox. I opted not to do the Cox setup as it was an extra $20 which I thought would have just setup the wireless (which I can handle). Is it a setting or something that I missed that needs to be setup? The firmware for the CG3000D is awful and not fun to use. I did change some hidden settings on the RgServices.asp page (I'll attach a screenshot). I've also heard that the Router/Modem combos are awful and that I should go back and just ask for a modem stand-alone. Any input is helpful. All screenshots: http://imgur.com/a/JX6qu#0

  Read the article

• Windows 7 cannot connect wirelessly to Netgear Router WPN824 V2

  - by edo152

  I have a new HP Laptop running Win 7 Home Premium with an Atheros Wireless card. I have a Negear WPN824 V2 Rangemax Router. The router works with a wired connection. Wirelessly it can see the network but it cannot connect. I have searched the web and the WPN824 seems to work for some people, but I cannot get it to connect. I have tried disabling Bonjour Service and a few other things but it continues not to connect. Am I probably correct to assume that the WPN824 is somehow incompatible with Wiondows 7? or am I missing some simple change I should make?

  Read the article

• How do I get the Netgear N150 USB wifi adapter working on 12.04?

  - by Jon

  Just installed latest version of ubuntu. I'm using a Netgear N150 Wireless USB Micro Adapter WNA1000M which keeps asking for network password over and over. I read elsewhere that I needed to install the latest driver for my chipset (RTL8188CUS) which I have and still no joy. If I run the steps listed in this thread while connected through ethernet, the wireless will connect just fine. If I disconnect the ethernet, the wifi will even continue to work, but after a restart or two I will lose connection. If I repeat the steps listed in the aforementioned thread, it will not re-connect wifi unless I run those steps while connected to ethernet.......so strange...

  Read the article

• why would resetting the Netgear N300 router fix my Win 7 laptop's slow wifi?

  - by rjnagle

  In the past day the wifi download speeds of my Win 7 HP 64 bit laptop have slowed considerably. I am trying to troubleshoot the problem and to figure out whether it's hardware related (i.e., is the Intel(R) Centrino(R) Wireless-N 2230 the problem?) or router related. I have a Netgear N300 router connected to my modem. I'm using Speedtest to measure my speed. First, during my problem state, my ipad can download and upload at normal speeds. It's only my Win 7 laptop which is having problems. Because my ipad downloads at normal speeds, that would tell me that the problem is specific to the laptop (either HW or SW). But when I restarted my Netgear router, the laptop wifi problems disappeared. That just doesn't make sense. If we know that one device can connect properly to the router, why would a laptop have problems? What are some possible reasons why this might happen? Also, during my problem state, I noticed that on my laptop upload speeds were faster than my download speeds. Anybody have a guess about what might cause upload speeds on one device to be faster than another? Is there any actions i could take (or options to enable) so this problem won't occur. (I initially thought my problem might be software related or memory related -- Norton AV or browser plugins. But even after I disabled everything and made sure memory footprint was minimal, the slowdown was still occurring -- and it solved itself altogether when the router was reset).

  Read the article

• Port-forwarding on livebox to router

  - by Yusuf

  Hello, At home, I have two routers, one Livebox and a Netgear. The reason why I need the Livebox is that the phone line cannot be connected to the Netgear router. So I have the Livebox connected to the phone line, the Netgear connected to the Livebox, and all PCs connected to the Netgear. My issue is that for every application or port that I want to give external access, I have to create entry in both the Livebox and the Netgear routers; so I would like to know if there's a way to automatically forward all requests to the Netgear router, from which I will then forward to the required IP:port. Thanks in advance.

  Read the article

• Netgear routers don't allow you to disable wireless admin??

  - by MousePad

  I just bought a new router, the NetGear WGR614. Nowhere in the settings can you disable the ability to administrate the router from a wireless connection, which opens it up to brute force attacks from outside the building. Furthermore, it doesn't require a direct connection to the router to admin either, you can admin it while you're connected to the Internet. This means it opens itself to the possibility of an attack from within the network. This is unbelievable to me. What am I missing? Can this be possible?

  Read the article

• Cannot connect to secure wireless with Netgear wna3100 USB

  - by Vince Radice

  I have installed Ubuntu 11.10. I used a wired connection to download and install all of the updates. When I tried to use a Netgear WNA3100 wireless USB network adapter, it failed. Much searching and trying things I was finally able to get it working by disabling security on my router. I have verified this by disabling security and I was able to connect. When I enabled security (WPA2 PSK), the connection failed. What is necessary to enable security (WPA2 PSK) and still use the Netgear USB interface? Here is the output from the commands most requested lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 003: ID 0846:9020 NetGear, Inc. WNA3100(v1) Wireless-N 300 [Broadcom BCM43231] lshw -C network *-network description: Ethernet interface product: RTL-8139/8139C/8139C+ vendor: Realtek Semiconductor Co., Ltd. physical id: 3 bus info: pci@0000:02:03.0 logical name: eth0 version: 10 serial: 00:40:ca:44:e6:3e size: 10Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=8139too driverversion=0.9.28 duplex=half latency=32 link=no maxlatency=64 mingnt=32 multicast=yes port=MII speed=10Mbit/s resources: irq:19 ioport:c800(size=256) memory:ee011000-ee0110ff memory:40000000-4000ffff *-network description: Wireless interface physical id: 1 logical name: wlan0 serial: e0:91:f5:56:e1:0d capabilities: ethernet physical wireless configuration: broadcast=yes driver=ndiswrapper+bcmn43xx32 driverversion=1.56+,08/26/2009, 5.10.79.30 ip=192.168.1.104 link=yes multicast=yes wireless=IEEE 802.11g iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11g ESSID:"vincecarolradice" Mode:Managed Frequency:2.422 GHz Access Point: A0:21:B7:9F:E5:EE Bit Rate=121.5 Mb/s Tx-Power:32 dBm RTS thr:2347 B Fragment thr:2346 B Encryption key:off Power Management:off Link Quality:76/100 Signal level:-47 dBm Noise level:-96 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 ndiswrapper -l bcmn43xx32 : driver installed device (0846:9020) present lsmod | grep ndis ndiswrapper 193669 0 dmesg | grep -e ndis -e wlan [ 907.466392] ndiswrapper version 1.56 loaded (smp=yes, preempt=no) [ 907.838507] ndiswrapper (import:233): unknown symbol: ntoskrnl.exe:'IoUnregisterPlugPlayNotification' [ 907.838955] ndiswrapper: driver bcmwlhigh5 (Netgear,11/05/2009, 5.60.180.11) loaded [ 908.137940] wlan0: ethernet device e0:91:f5:56:e1:0d using NDIS driver: bcmwlhigh5, version: 0x53cb40b, NDIS version: 0x501, vendor: 'NDIS Network Adapter', 0846:9020.F.conf [ 908.141879] wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSK [ 908.143048] usbcore: registered new interface driver ndiswrapper [ 908.178826] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 994.015088] usbcore: deregistering interface driver ndiswrapper [ 994.028892] ndiswrapper: device wlan0 removed [ 994.080558] ndiswrapper version 1.56 loaded (smp=yes, preempt=no) [ 994.374929] ndiswrapper: driver bcmn43xx32 (,08/26/2009, 5.10.79.30) loaded [ 994.404366] ndiswrapper (mp_init:219): couldn't initialize device: C0000001 [ 994.404384] ndiswrapper (pnp_start_device:435): Windows driver couldn't initialize the device (C0000001) [ 994.404666] ndiswrapper (mp_halt:262): device e05b6480 is not initialized - not halting [ 994.404671] ndiswrapper: device eth%d removed [ 994.404709] ndiswrapper: probe of 1-5:1.0 failed with error -22 [ 994.406318] usbcore: registered new interface driver ndiswrapper [ 2302.058692] wlan0: ethernet device e0:91:f5:56:e1:0d using NDIS driver: bcmn43xx32, version: 0x50a4f1e, NDIS version: 0x501, vendor: 'NDIS Network Adapter', 0846:9020.F.conf [ 2302.060882] wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSK [ 2302.113838] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 2354.611318] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 2355.268902] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 2365.400023] wlan0: no IPv6 routers present [ 2779.226096] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 2779.422343] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 2797.574474] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 2802.607937] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 2803.261315] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 2813.952028] wlan0: no IPv6 routers present [ 3135.738431] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 3139.180963] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3139.816561] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3163.229872] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3163.444542] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3163.758297] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3163.860684] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3205.118732] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3205.139553] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3205.300542] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3353.341402] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 3363.266399] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3363.505475] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3363.506619] ndiswrapper (set_iw_auth_mode:601): setting auth mode to 5 failed (00010003) [ 3363.717203] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3363.779206] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3405.206152] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3405.248624] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3405.577664] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3438.852457] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 3438.908573] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3568.282995] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3568.325237] ndiswrapper (set_iw_auth_mode:601): setting auth mode to 5 failed (00010003) [ 3568.460716] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3568.461763] ndiswrapper (set_iw_auth_mode:601): setting auth mode to 5 failed (00010003) [ 3568.809776] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3568.880641] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3610.122848] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3610.148328] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3610.324502] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3636.088798] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 3636.712186] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 3647.600040] wlan0: no IPv6 routers present I am using the system now with the router security turned off. When I submit this, I will turn security back on.

  Read the article

• Netgear GS724Tv3 and link aggregation Mac OS X Server 10.6.8

  - by Manca Weeks

  I need to link aggregate 2 sets of ports on the Netgear GS724T with my Apple server tower (latest generation). I have 2 built in ports and 2 ports on a PCIe ethernet card. It is not obvious to me how to properly configure the Netgear end. I have access to the Netgear box through its web interface, just don't know how to properly set the settings. I tried going to Netgear for help, but they said my software support has expired. I bought this unit on their recommendation - they say it is compatible with 802.3ad protocol. I cannot locate any references to this protocol in the manual and I noticed some people in formus say that this device is actually not compatible with 802.3ad and that Netgear is misleading potential customers by saying it is. Any help will be appreciated. Thanks, M My own answer - posted as edit because of restrictions on my user: OK folks, turns out one must use a Windows machine on this one or nothing makes sense. I was unable to get much farther than viewing the default inactive LAGs because in Firefox and Safari on Mac things don't make much sense - i.e. the Apply buttons (supposedly JavaScript) don't work. You can view the configurations, but none of the modifications you make stick. Then, in Switching - LAGs, choose the ports to include and make sure you switch the LAG type from Static to LACP and all is well. Haven't tested the performance of the config yet, but both sides appear to be happy with the configuration. Apple server says link active and so does the Netgear. Will report if any other discoveries. Thanks for all who read and to user84104 for responding. M

  Read the article

• Can I use 2 different models of Netgear Powerline Network Adapters together?

  - by user36388

  I have a set of XETB1001 and a set of XAVB101, I want to use the set of XAVB101 because they are 200mbps and 1 XETB1001, is that possible, or do I need to keep them paired? Links to Products from Newegg.com XETB1001 - newegg.com/Product/Product.aspx?Item=N82E16833122318 XAVB101 - newegg.com/product/product.aspx?Item=N82E16833122233

  Read the article

• Server IP must be a LAN IP (Port Forwarding Netgear Router)? [closed]

  - by rphello101

  I'm trying to set up a server (Apache) on my computer (fairly new to it). As I understand it, for it to be accessible to other computers, I need to forward port 80. When I try to forward the port though, I get the error: Server IP must be a LAN IP. I noticed in ipconfig that my default gateway is different than my wireless router. My computer is not hardwired, not on WiFi. Furthermore, I do not, at this point, have a static IP. I read that it should still work with a dynamic IP until it changes. Any ideas on what I can do? I'm using Windows 7 in case it matters.

  Read the article

• recent unreliable wireless connection with Netgear KWGR614 router

  - by gabkdlly

  Recently, my internet connection over wireless ( via a Netgear KWGR614 router ) has become unreliable, on both a Dell laptop running Ubuntu 10.04 as well as my Desktop running Ubuntu 10.10 . The problem does not seem to occur on a laptop running Windows Vista, nor on a Desktop running Windows 7 ( this machine is connected with an ethernet cable ). The problem does not seem to occur on my Openmoko Freerunner ( running Android 1.5 ), though I hardly ever use this device to connect over WLAN, so the problem may have just slipped by. On my main Ubuntu Desktop, I have tried the following wireless devices: a Longshine PCI card ( an old device with an RTL8180L chip ) a D-Link DWL-510 PCI card ( this device threw warnings in dmesg ) a USB device from MSI ( US54EX ). Usually my wireless network shows up in the network manager with a normal signal strength, even when the connection speed is slow or the connection gets reset ( asking me to click connect to re-authenticate my wireless connection ). I know that this router is susceptible to denial of service attacks, as I have previously been able to disrupt its operation by putting an nmap scan into a while loop. Is it possible that someone is jamming my signal ?

  Read the article

• Wireless connection disconnects and reconnects with a Netgear WNA1000

  - by William Berkenkamp

  Ever since I made the permanent switch from Vista to Ubuntu i've had wireless connectivity problems. From watching the network manager when it disconnects it seems like it turns off the receiver for some reason. Could it be bad drivers? I used their install software and the site doesn't really offer driver downloads. The adapter is a Netgear WNA1000 if memory serves, and I don't know much about the router except that it's a Motorola Surfboard. And I figure this might help a bit *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 01 serial: 00:1b:b9:a7:39:a4 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=N/A latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:40 ioport:d800(size=256) memory:feaff000-feafffff memory:feac0000-feadffff *-network description: Wireless interface physical id: 1 bus info: usb@2:1.1 logical name: wlan0 serial: 00:26:f2:8b:fb:38 capabilities: ethernet physical wireless configuration: broadcast=yes driver=carl9170 driverversion=3.2.0-24-generic-pae firmware=1.9.4 ip=10.0.0.36 link=yes multicast=yes wireless=IEEE 802.11bgn I have tried installing WICD and it didn't fix the problem. Any help would be greatly appreciated. This problem is greatly limiting what I can do with my computer.

  Read the article

• Very slow wireless connection (unrelated to power management) using Netgear N150 WNA1100 in 12.04

  - by vgaldikas

  I am using a Netgear N150 WNA1100 USB Adapter. The network driver is: ath9k_htc. When I use Ubuntu 12.04 my wireless connection is much slower than when I use the WNA1100 with my Windows 7 installation on the same machine. I have been researching this and the most common reason for this seems to be related to power management. However for me this is off by default. I had entered a bunch of different commands and, at one stage, I got it to work at full power. But then I rebooted the machine and it went back to slow again. After entering the different commands I was afraid that I may have messed something up, so I performed a fresh install of Ubuntu. I still have the same problem. My wireless connection is still much slower when using Ubuntu than when using Windows 7. I am not sure what other info could help... EDIT: Ok, I have made live usb from the iso file I used to install Ubuntu on this pc, and ran it on my laptop. Still the same problem. However la[top works grand on cable. I suppose this means that my wireless adapter or network driver can be eliminated as root of the problem.. So maybe to do with router itself? I use ZyXEL P-660HW-D1

  Read the article

• Windows Wireless Drivers - Install

  - by Justin Y.

  I have nearly ended my journey of making a dual-boot windows xp and ubuntu computer. Along with version 12.04, came the problem with my NetGear WNDA3100v2 wireless adapter. It wasn't compatible. My last step in my adventure is to install the software called Windows Wireless Drivers. I have internet access on my laptop and a flash drive. It would be preferable to receive a link to this program, because I see no link on the website, and I can't download it from the Ubuntu Software Center. Thanks.

  Read the article

• Netgear WNA1100 stopped working

  - by NOLFXceptMe

  I'm facing a rather strange issue with the USB wireless adapter WNA1100. I was able to connect to wireless using this yesterday. However, today am not. lsmod shows ath9k_htc, ath9k_common, ath9k_hw, ath and ndiswrapper. I'm not sure if this is relevant to the above problem, but between yesterday and today, the only change was an upgrade to Ubuntu 2.6.38 kernel, which caused the NVIDIA driver to break (I have a 7300GT), so I had to ignore that kernel, reboot into 2.6.35, and rebuild NVIDIA module from NVIDIA-Installer-270.run. Help?

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >