Search Results

Search found 467 results on 19 pages for 'outbound'.

Page 2/19 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• Typical outbound port list for guest access?

  - by Steve

  I manage a weekly rental house that includes wireless Internet access. I've allowed all outbound ports on my router but my ISP has disabled my Internet access twice now because guests have downloaded (or served up) copyrighted content. So I'd like to institute some port filtering to discourage p2p sharing (see disclaimer below). But I don't want to inconvenience the 99.9% of folks who keep things above-board. My question is, what outbound ports are typically open for rental/hotel wireless Internet access, or where can I find such a list? TCP 80,443,25,110 at a minimum. Though my own email service uses 995 and 465 for SSL, some may use IMAP, I personally use SSH and FTP, so I'll open those. Roughly I figure I need to open access to privileged ports, and close 1024 & above. Is there a whitelist I should institute for commonly used high ports? And does it make sense to block UDP 1024 ? Disclaimer: I realize anyone replying to this message could circumvent the port filtering and share content to their heart's content. I do not need comprehensive p2p blocking, which requires more than a port whitelist. Anyone staying at the house shoulders the responsibility for their Internet use, per the rental contract. Also anyone savvy enough to circumvent the port filters would hopefully be savvy enough to use some sort of peer blocking, thereby preventing the ISP from taking down the service.

  Read the article

• Redirection of outbound UDP port NTP.

  - by pboin

  For my residential service, I changed ISPs to Zoom/Armstrong. Just after that, my NTP daemons stopped working. I dug deep and diagnosed the problem: Unprivileged ports are getting out. When i run 'ntpdate' for example, I go out on a high, unprivleged port, and get a response on UDP 123. That's fine. The 'ntpd' daemon though, expects to go out on 123 and get its reply there as well. This must be a common problem, because it's directly addressed in the NTP troubleshooting guide. Just to see what would happen, I wrote a detailed email to the general support address at Armstrong. They replied almost immediately with a complete technical answer! They have everything <1024 blocked, except for a few ports to support outbound VPN. So, the question: Can I use IPtables to essentially re-write my outbound UDP 123 up to 2123 or something like that? If I do, does there need to be a corresponding 2123-123 rule to translate the reply? This seems like NAT, but with ports, not addresses. True, I could run ntpdate from cron, but that loses all of the adjustment smarts of NTP.

  Read the article

• Redirection of outbound UDP port.

  - by pboin

  For my residential service, I changed ISPs to Zoom/Armstrong. Just after that, my NTP daemons stopped working. I dug deep and diagnosed the problem: Unprivileged ports are getting out. When i run 'ntpdate' for example, I go out on a high, unprivleged port, and get a response on UDP 123. That's fine. The 'ntpd' daemon though, expects to go out on 123 and get its reply there as well. This must be a common problem, because it's directly addressed in the NTP troubleshooting guide. Just to see what would happen, I wrote a detailed email to the general support address at Armstrong. They replied almost immediately with a complete technical answer! They have everything <1024 blocked, except for a few ports to support outbound VPN. So, the question: Can I use IPtables to essentially re-write my outbound UDP 123 up to 2123 or something like that? If I do, does there need to be a corresponding 2123-123 rule to translate the reply? This seems like NAT, but with ports, not addresses. I tried, but can't seem to get iptables to do what I want. I'm not sure if it's my lack of skill, or if I'm trying the wrong solution. True, I could run ntpdate from cron, but that loses all of the adjustment smarts of NTP.

  Read the article

• Outbound ports to allow through firewall - core requirements

  - by dunxd

  This question was asked before, but in a rather general way. I'm asking more specifically based on my current requirements. We have a number of remote offices made up of a bunch of PCs and an ASA 5505 which is used as firewall and VPN termination point. In the offices we share the internet connection with one or more other organisations over whom we have very little control, asides from the config on the ASAs. For a bunch of reasons I'd like to lock down these ASA 5505s to only allow outbound traffic to ports used by applications we know we need. I'm putting a standard config to roll out to all the ASAs, and if we need to open up ports for the other orgs we can do it on request. But I want to leave open the most commonly required ports so we can get up and running without waiting on other folks technical staff to get back. I plan to allow the following TCP ports to support email and web access, which I know everyone will need: POP3 (110 and 995) HTTP (80 and 443) IMAP4 (143 and 993) SMTP (25 and and 465) The question really is, what other ports do I need to leave open to allow for "normal" working? I've seen UDP port 53 for DNS as one. Are there any others that would be worth opening up? Just to note - I'll also be setting up monitoring systems to keep an eye on the ports we do allow. Any of the above could be misused of course. We'll also back all this up with signed agreements. But I'm aiming for a technical solutions where I don't have to start out with the full requirements of everyone we share connections with. See also: outbound ports that are always open

  Read the article

• Outbound ports to allow through firewall

  - by dunxd

  This question was asked before, but in a rather general way. I'm asking more specifically based on my current requirements. We have a number of remote offices made up of a bunch of PCs and an ASA 5505 which is used as firewall and VPN termination point. In the offices we share the internet connection with one or more other organisations over whom we have very little control, asides from the config on the ASAs. For a bunch of reasons I'd like to lock down these ASA 5505s to only allow outbound traffic to ports used by applications we know we need. I'm putting a standard config to roll out to all the ASAs, and if we need to open up ports for the other orgs we can do it on request. But I want to leave open the most commonly required ports so we can get up and running without waiting on other folks technical staff to get back. I plan to allow the following TCP ports to support commonly required resources: POP3 (110 and 995) HTTP (80 and 443) IMAP4 (143 and 993) SMTP (25 and and 465) The question really is, what other ports do I need to leave open to allow for "normal" working. I've seen UDP port 53 for DNS as one. Are there any others that would be worth opening up? Just to note - I'll also be setting up monitoring systems to keep an eye on the ports we do allow. Any of the above could be misused of course. We'll also back all this up with signed agreements. But I'm aiming for a technical solutions where I don't have to start out with the full requirements of everyone we share connections with. See also: outbound ports that are always open

  Read the article

• WatchGuard 'Internal Policy' intermittently blocking outbound web traffic

  - by vfilby

  I have a lot of legitimate outbound traffic intermittently being denied by WatchGuard's "Internal Policy." Today I tried to go to Splunk's homepage and my traffic was denied by my watchguard XTM 22 with Pro upgrade. What is the "Internal Policy" and what can I do to control it? Example of Traffic being blocked Type Date Action Source IP Port Interface Destination IP Port Policy Traffic 2011-09-21T18:24:43 Deny 10.0.0.90 49627 3-Primary LAN 64.127.105.40 80 Firebox Internal Policy http/tcp Top three firewall policies:

  Read the article

• about inbound and outbound bandwidth

  - by bogdan

  how do i check my available inbound and outbound bandwidth? What is influencing them? Thank you for your support!!

  Read the article

• forward outbound traffic rule

  - by Claudiu

  I am trying to forward the outbound traffic to another server. Current rule is: /sbin/iptables -A OUTPUT -p tcp -s localhost -o 91.xxx.xxx.xxx --dport 65000:65010 -j ACCEPT but when I do a iptables -L, the rule its showed like this: ACCEPT tcp -- localhost.localdomain anywhere tcp dpts:65000:65010 So I guess my rule is bad written since the "destination" column shows "anywhere" Can you help me with this?

  Read the article

• iptables rule for forwarding outbound traffic

  - by Claudiu

  I am trying to forward the outbound traffic to another server. Current rule is: /sbin/iptables -A OUTPUT -p tcp -s localhost -o 91.xxx.xxx.xxx --dport 65000:65010 -j ACCEPT but when I do a iptables -L, the rule its showed like this: ACCEPT tcp -- localhost.localdomain anywhere tcp dpts:65000:65010 So I guess my rule is bad written since the "destination" column shows "anywhere" Can you help me with this?

  Read the article

• HP LoadRunner - measurements to watch outbound active TCP ports

  - by user57555

  I am trying to find out if there are any relevant measurements that LoadRunner can track, when running a load test - where it can allow me to monitor the number of active outbound ports from a given windows 2003 box. i am seeing that there are various measurements specific to CLR and IIS - such as current connections, but i am looking for something that can show the active outbound ports, at any given time, during the load test. thank you.

  Read the article

• Postfix Stagger/Rate Limit Outbound Mail

  - by GruffTech

  We have a server that sends our weekly newsletter to subscribers, To prevent people like Hotmail or Yahoo from blocking us due to sending too many simultaneous emails to them, Is there a way we can stagger email, or rate-limit outbound emails from postfix? Keep in mind, I dont want the mailserver to stop queueing mail or accepting new messages, Simply defer delivery if there are more then 3-4 messages per destination domain/ipaddress, or something similar. Note: I dont want a Sender Throttle, as described in a similar question, here. I'm looking more for a recipient throttle but haven't had any luck finding out how to do so with PolicyD or Anvil services, and was wondering if anyone else has accomplished such a task.

  Read the article

• MS Exchange -- running code against outbound email

  - by user32680

  I would like to know if using MS Exchange there is a way to run code against outbound emails. The code would need to trigger on emails sent to a specific domain, connect to a database, check for an email related to the email sent, and Carbon-copy that email to the related email. What I'm trying to do: When [email protected] gets an email, his auditor [email protected] gets CC'd. Jack is in a MSSQL DB table related to his auditor's email. Are there any samples of things like this being done?

  Read the article

• Shaping outbound Traffic to Control Download Speeds with Linux

  - by Kyle Brandt

  I have a situation where a server makes lots of requests from big webservers all at the same time. Currently, I have not control over the amount of requests or the rate of the requests from the application that does this. The responses from these webservers is more than the internet line can handle. (Basically, we are launching a DoS on ourselves). I am going to get push to get this fixed at the application level, but for the time being, is there anyway I can use traffic shaping on the Linux server to control this? I know I can only shape outbound traffic, but maybe there is a way I can slow the TCP responses so the other side will detect congestion and this will help my situation? If there is anything like this with tc, what might the configuration look like? The idea is that the traffic control might help me control which packets get dropped before they reach my router.

  Read the article

• Get source and destination of outbound traffic in pfSense

  - by maxsilver

  I'm looking at the traffic graph in pfSense (Version 1.2.2), which we're using as a router / NAT / ect on our network. Recently, I'm seeing a sudden, constant spike of 15 - 30kbps traffic outbound, that is unusual for our network (normally its below 2kbps, we're mostly all inbound traffic) Is there any way to determine what the source of this traffic is, or where it's going? (Just an internal IP address for source, and external IP address for destination would be all I need) I've already tried switching the traffic graph to 'LAN' and watching the host list on the right side, but it seems ... flakey. The numbers it shows seem to fade in and out at random, and the values never add up to anywhere near the graph values. I'm not allowed to post the image, but a photo is available at - http://imgur.com/QYjKI.png

  Read the article

• asterisk outbound caller id

  - by MCS

  I'm trying to set the caller id number for an outbound call. My asterisk .call file looks like this: Channel: SIP/flowroute/1234567890 Context: test Extension: 1234567890 Priority: 1 Here's my extensions.conf: [test] exten => _1NXXXXXXXXX,1,Set(CALLERID(num)=8005552222) exten => _1NXXXXXXXXX,n,Dial(SIP/${EXTEN}@flowroute) exten => _1NXXXXXXXXX,n,Playback(hello-world) When I receive the call, the caller id number is 1-206-445-6979, even though the CDR log has both src and clid set to 8005552222. I'm using flowroute as my carrier. Is there something wrong on their side?

  Read the article

• Redirect outbound traffic on port 53 to port 5300 with iptables

  - by Zagorax

  I'm running a local dns server on port 5300 to develop a software. I need my machine to use that dns but I wasn't able to tell /etc/resolv.conf to check on a different port. I searched a bit on google and I didn't find a solution. I set 127.0.0.1 as nameserver on /etc/resolv.conf. Could you please tell me how can I redirect outbound traffic on port 53 to another port? I tried the following but it didn't work: iptable -t nat -A PREROUTING -p tcp --dport 53 -j DNAT --to 127.0.0.1:5300 iptable -t nat -A PREROUTING -p udp --dport 53 -j DNAT --to 127.0.0.1:5300

  Read the article

• Creating static NAT blocks outbound traffic Cisco ASA

  - by natediggs

  Hi Everyone, I have two web servers sitting behind a Cisco ASA 5505, which I don't have much experience with. I'm trying to create two static NATs. One static NAT that goes to xx.xx.xx.150 and another that goes to xx.xx.xx.151. I've created the static NAT for the .150 web server and it works FINE. Incoming and outgoing traffic work great. This is the staging web server. I now need to duplicate the setup for the production web server. So, I connect the webserver to the firewall, change the public IP address on one of the NICs reboot the server and I have outbound internet access. Then I run the command: static (inside,outside) xx.xx.xx.150 192.168.1.x which is successful. I then run the command: access-list acl-outside permit tcp any host xx.xx.xx.150 eq 80 Which is successful. I then try to browse the internet and I get nothing. I try to telnet in through port 80 and I get nothing (though I'm guessing because the response to the telnet request is being blocked). I've tried this with the production web server and then I tried it with another web server that is for internal testing and have the exact same problem. Both work fine until I run the static NAT rule and then no outbound internet access. I have a feeling that it's something simple that I'm missing, but my limited experience with this device is killing me. Below I've pasted the current configuration. I'm currently trying to get this to work on the .153 server which is the internal testing server. Once I can verify that works, I'll try it with production. : Saved : ASA Version 8.2(4) ! hostname QG domain-name XX.com enable password passwd names ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.1.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address XX.XX.XX.148 255.255.255.0 ! interface Vlan3 shutdown no forward interface Vlan1 nameif dmz security-level 50 ip address dhcp ! boot system disk0:/asa824.bin ftp mode passive clock timezone EST -5 clock summer-time EDT recurring dns server-group DefaultDNS domain-name fw.XXgroup.com same-security-traffic permit inter-interface access-list acl-outside extended permit tcp any host XX.XX.XX.150 eq www access-list acl-outside extended permit tcp any host XX.XX.XX.150 eq https access-list acl-outside extended permit tcp any host XX.XX.XX.151 eq www access-list acl-outside extended permit tcp any host XX.XX.XX.151 eq https access-list acl-outside extended permit tcp any host XX.XX.XX.153 eq www access-list inside_access_in extended permit ip 192.168.1.0 255.255.255.0 any access-list inside_nat0_outbound extended permit ip any 192.168.1.32 255.255.255.240 pager lines 24 logging enable logging asdm informational mtu inside 1500 mtu outside 1500 mtu dmz 1500 ip local pool VPNIPs 192.168.1.35-192.168.1.44 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-635.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) XX.XX.XX150 192.168.1.100 netmask 255.255.255.255 static (inside,outside) XX.XX.XX153 192.168.1.102 netmask 255.255.255.255 access-group acl-outside in interface outside route outside 0.0.0.0 0.0.0.0 XX.XX.XX129 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy aaa authorization command LOCAL http server enable http 192.168.1.0 255.255.255.0 inside http 0.0.0.0 0.0.0.0 outside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map outside_dyn_map 20 set pfs group1 crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication crack encryption 3des hash sha group 2 lifetime 86400 no crypto isakmp nat-traversal client-update enable telnet timeout 5 ssh timeout 5 console timeout 0 dhcpd auto_config outside ! dhcpd address 192.168.1.2-192.168.1.33 inside dhcpd dns 208.77.88.4 interface inside dhcpd enable inside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept webvpn enable outside svc image disk0:/sslclient-win-1.1.0.154.pkg 1 svc image disk0:/anyconnect-win-2.5.2019-k9.pkg 2 svc enable group-policy ATSAdmin internal group-policy ATSAdmin attributes dns-server value 208.77.88.4 208.85.174.9 vpn-tunnel-protocol IPSec svc webvpn webvpn url-list none svc keep-installer installed svc rekey method ssl svc ask enable username qgadmin password /oHfeGQ/R.bd3KPR encrypted privilege 15 username benl password 0HNIGQNI0uruJvhW encrypted privilege 0 username benl attributes vpn-group-policy ATSAdmin username kuzma password rH7MM7laoynyvf9U encrypted privilege 0 username kuzma attributes vpn-group-policy ATSAdmin username nate password BXHOURyT37e4O5mt encrypted privilege 0 username nate attributes vpn-group-policy ATSAdmin tunnel-group ATSAdmin type remote-access tunnel-group ATSAdmin general-attributes address-pool VPNIPs default-group-policy ATSAdmin tunnel-group SSLVPN type remote-access tunnel-group SSLVPN general-attributes address-pool VPNIPs default-group-policy ATSAdmin ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect esmtp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp inspect ip-options ! service-policy global_policy global privilege cmd level 3 mode exec command perfmon privilege cmd level 3 mode exec command ping privilege cmd level 3 mode exec command who privilege cmd level 3 mode exec command logging privilege cmd level 3 mode exec command failover privilege show level 5 mode exec command running-config privilege show level 3 mode exec command reload privilege show level 3 mode exec command mode privilege show level 3 mode exec command firewall privilege show level 3 mode exec command interface privilege show level 3 mode exec command clock privilege show level 3 mode exec command dns-hosts privilege show level 3 mode exec command access-list privilege show level 3 mode exec command logging privilege show level 3 mode exec command ip privilege show level 3 mode exec command failover privilege show level 3 mode exec command asdm privilege show level 3 mode exec command arp privilege show level 3 mode exec command route privilege show level 3 mode exec command ospf privilege show level 3 mode exec command aaa-server privilege show level 3 mode exec command aaa privilege show level 3 mode exec command crypto privilege show level 3 mode exec command vpn-sessiondb privilege show level 3 mode exec command ssh privilege show level 3 mode exec command dhcpd privilege show level 3 mode exec command vpn privilege show level 3 mode exec command blocks privilege show level 3 mode exec command uauth privilege show level 3 mode configure command interface privilege show level 3 mode configure command clock privilege show level 3 mode configure command access-list privilege show level 3 mode configure command logging privilege show level 3 mode configure command ip privilege show level 3 mode configure command failover privilege show level 5 mode configure command asdm privilege show level 3 mode configure command arp privilege show level 3 mode configure command route privilege show level 3 mode configure command aaa-server privilege show level 3 mode configure command aaa privilege show level 3 mode configure command crypto privilege show level 3 mode configure command ssh privilege show level 3 mode configure command dhcpd privilege show level 5 mode configure command privilege privilege clear level 3 mode exec command dns-hosts privilege clear level 3 mode exec command logging privilege clear level 3 mode exec command arp privilege clear level 3 mode exec command aaa-server privilege clear level 3 mode exec command crypto privilege cmd level 3 mode configure command failover privilege clear level 3 mode configure command logging privilege clear level 3 mode configure command arp privilege clear level 3 mode configure command crypto privilege clear level 3 mode configure command aaa-server prompt hostname context call-home profile CiscoTAC-1 no active destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address email [email protected] destination transport-method http subscribe-to-alert-group diagnostic subscribe-to-alert-group environment subscribe-to-alert-group inventory periodic monthly subscribe-to-alert-group configuration periodic monthly subscribe-to-alert-group telemetry periodic daily Cryptochecksum:0ed0580e151af288d865f4f3603d792a : end asdm image disk0:/asdm-635.bin no asdm history enable

  Read the article

• Salesforce/PHP - outbound messages (SOAP) - memory limit issue

  - by Phill Pafford

  I'm using Salesforce to send outbound messages (via SOAP) to another server. The server can process about 8 messages at a time, but will not send back the ACK file if the SOAP request contains more than 8 messages. SF can send up to 100 outbound messages in 1 SOAP request and I think this is causing a memory issue with PHP. If I process the outbound messages 1 by 1 they all go through fine, I can even do 8 at a time with no issues. But larger sets are not working. ERROR in SF: org.xml.sax.SAXParseException: Premature end of file Looking in the HTTP error logs I see that the incoming SOAP message looks to be getting cut of which throws a PHP warning stating: Premature end of data in tag ... PHP Fatal error: Call to a member function getAttribute() on a non-object This leads me to believe that PHP is having a memory issue and can not parse the incoming message due to it's size. I was thinking I could just set: ini_set('memory_limit', '64M'); But would this be the correct approach? Is there a way I could set this to increase with the incoming SOAP request dynamically? UPDATE: Adding some code $data = fopen('php://input','rb'); $headers = getallheaders(); $content_length = $headers['Content-Length']; $buffer_length = 1000; $fread_length = $content_length + $buffer_length; $content = fread($data,$fread_length); /** * Parse values from soap string into DOM XML */ $dom = new DOMDocument(); $dom->loadXML($content); ....

  Read the article

• How to work around blocked outbound hkp port for apt keys

  - by kief_morris

  I'm using Ubuntu 9.10, and need to add some apt repositories. Unfortunately, I get messages like this when running sudo apt-get update: W: GPG error: http://ppa.launchpad.net karmic Release: The following signatures couldn't be verified because the public key is not available: NO_PUBKEY 5A9BF3BB4E5E17B5 W: GPG error: http://ppa.launchpad.net karmic Release: The following signatures couldn't be verified because the public key is not available: NO_PUBKEY 1DABDBB4CEC06767 So, I need to install the keys for these repositories. Under 9.10 we now have the option to do this: sudo add-apt-repository ppa:nvidia-vdpau/ppa See this Ubuntu help article for details. This is great, except that I'm running this on a workstation behind a firewall which blocks outbound connections to pretty much all ports except those required by secretaries running Windows and IE. The port in question here is the hkp service, port 11371. There appear to be ways to manually download keys and install them on apt's keyring. There may even be a way to use add-apt-repository or wget or something to download a key from an alternative server making it available on port 80. However, I haven't yet found a concise set of steps for doing so. What I'm looking for is: How to find a public key for an apt-package (recommendations for resources which have these, and/or tips for searching. Searching for the key hash doesn't seem all that effective so far.) How to retrieve a key (can it be done automatically using gpg or add-apt-repository?) How to add a key to apt's keyring Thanks in advance.

  Read the article

• Outbound mail issue during Exchange 2003 migration

  - by user27574

  Dear all, I am having an outbound email issue during the Exch 03 migration. Basically, we are migrating Exch03 to new hardware, both servers are Server 03 based. Everything runs smooth while setting up and installing Exch 03 on the new box. Public folders are all replicated. My issues are shown below.... 1) After starting to move users' mailboxes to new Exch 03, they receive some undeliverable mail and bounced back mail from some vendors, then I move few users back to test around, they have no problem at all after moving back to old Exch 03. 2) Another issue is our company has Blackberry users, we don't have BES. Under each user's mailboxes, we have forward rule setup, so that both user inbox and BB can receive email. User who is moved to the new Exch 03 server, they can only send email to the BB user's inbox, mail cannot be forwarded to BB at all, smtp queue stacks up and keep trying until the time is expired. Since not all emails that the users send out from the new Exch have problem, I am not able to narrow down what is the issue here. Can anyone give me some ideas? Could this be MX record / Reversed DNS relate? Or firewall NAT rule setting? Thanks.

  Read the article

• No outbound internet connection after restarting CentOS 6.3

  - by wnstnsmth

  After restarting a headless CentOS 6.3 machine, it lost outbound internet connectivity, i.e. I can still connect to the server via SSH (ssh root@**.126.18.56), but stuff such as ping google.com gives google.com: unknown host, and yum list some_package gives a lot of network errors. This is what ifconfig gives: eth0 Link encap:Ethernet HWaddr 00:25:90:78:2D:5D inet addr:**.126.18.56 Bcast:**.126.18.255 Mask:255.255.255.0 inet6 addr: fe80::225:90ff:fe78:2d5d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:75594 errors:0 dropped:0 overruns:0 frame:0 TX packets:787 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:7074741 (6.7 MiB) TX bytes:144391 (141.0 KiB) Interrupt:20 Memory:f7a00000-f7a20000 eth1 Link encap:Ethernet HWaddr 00:25:90:78:2D:5C UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) Interrupt:16 Memory:f7900000-f7920000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:6 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:504 (504.0 b) TX bytes:504 (504.0 b) I have absolutely no clue how to debug this, and I find it very strange since I can still connect via ssh. EDIT: Weirdly, /etc/resolv.conf does not contain any entries, or none that I can make sense of: # Generated by NetworkManager search sui-inter.net # No nameservers found; try putting DNS servers into your # ifcfg files in /etc/sysconfig/network-scripts like so: # # DNS1=xxx.xxx.xxx.xxx # DNS2=xxx.xxx.xxx.xxx # DOMAIN=lab.foo.com bar.foo.com So is it possible that rebooting the server erased that file? It worked before at least! And how do I solve this? By the way, pinging an IP address works.

  Read the article

• Repeated installation of malicious software to do outbound DDOS attack [duplicate]

  - by user224294

  This question already has an answer here: How do I deal with a compromised server? 12 answers We have a Ubuntu Vitual Private Server hosted by a Canadian company. Out VPS was affected to do "outbound DDOS attack" as reported by server security team. There are 4 files in /boot looks like iptable, please note that the capital letter "I","L". VPS:/boot# ls -lha total 1.8M drwx------ 2 root root 4.0K Jun 3 09:25 . drwxr-xr-x 22 root root 4.0K Jun 3 09:25 .. -r----x--x 1 root root 1.1M Jun 3 09:25 .IptabLes -r----x--x 1 root root 706K Jun 3 09:23 .IptabLex -r----x--x 1 root root 33 Jun 3 09:25 IptabLes -r----x--x 1 root root 33 Jun 3 09:23 IptabLex We deleted them. But after a few hours, they appeared again and the attack resumed. We deleted them again. They resurfaced again. So on and so forth. So finally we have to disable our VPS. Please let us know how can we find the malicious script somewhere in the VPS, which can automatically install such attcking software? Thanks.

  Read the article

• Route outbound connections from local network through VPN

  - by Sharkos

  I have a server A running OpenVPN, an OpenVPN client B (a rooted Android phone as it happens) and a third party C (a laptop, tablet etc.) tethered to B. B can use the VPN to access the internet via A; C can use the tethered connection WITHOUT the VPN to access the internet via B. However, with the VPN on B active, I cannot load information from the internet on C. A appears to log similar traffic inbound and outbound when B or C attempt to load a webpage, say, but the VPN on device B reports no inbound traffic when the connection originated from C. Where should I look for packets being dropped, and what ip rules should I use to make sure they are passed back through the VPN and into the local network B <- C? (I'll obviously post whatever further information is needed.) Further info Without VPN: root@android:/ # ip route default via [B's External Gateway] dev rmnet0 [B's External Subnet] dev rmnet0 proto kernel scope link src [B's External IP] [B's External Gateway] dev rmnet0 scope link 192.168.43.0/24 dev wlan0 proto kernel scope link src 192.168.43.1 With VPN: root@android:/ # ip route 0.0.0.0/1 dev tun0 scope link default via [B's External Gateway] dev rmnet0 [B's External Subnet] dev rmnet0 proto kernel scope link src [B's External IP] [B's External Gateway] dev rmnet0 scope link [External address of A] dev tun0 scope link 128.0.0.0/1 dev tun0 scope link 172.16.0.0/24 dev tun0 scope link 172.16.0.8/30 dev tun0 proto kernel scope link src 172.16.0.10 192.168.43.0/24 dev wlan0 proto kernel scope link src 192.168.43.1 192.168.168.0/24 dev tun0 scope link

  Read the article

• How to Configure Source NAT (Private IP => Public IP Outbound)

  - by DavidScherer

  I'm running VMWare ESXi Free and have Zentyal SBS 3.2 running as a Gateway. I have 5 Public IPS (CIDR/29, let's call them 69.1.1.1 - 69.1.1.5) and currently Zentyal is bound to 69.1.1.1 as the Gateway, with the other 4 Public IPs set as Virtual Interfaces in Zentyal (wan2-wan5) I have machines sitting on the Private Network (10.34.251.x) that, when going Outbound (to Google for instance) should be seen by the Internet as an IP other than the Gateway (69.1.1.1), this is because our machines need to be able to communicate with 3rd party APIs that expect these requests to come from a specific IP. From what I could find, SNAT (Source NAT) in Zentyal is used to achieve this, but I'm not sure how to configure it and cannot find a specific piece of Documentation for it at Zentyal. I've tried setting this up a couple different ways, with no results and at this point I have no idea if I'm going about this completely wrong, or my lack of experience with networking and the associated terminology is preventing me from placing the correct values in the correct fields. I get the following form to set up "SNAT" rules in Zentyal: Perhaps someone can offer some guidance and definitions for the fields above? SNAT Address Is this the Public IP I want to masquerade? Outgoing Interface Should this by my External NIC (one connected to Public 'Net), or is it the "Private" interface? It sounds as though this should be the External interface as I want the traffic from the internal network sent Out over this Interface (using a different IP than normal, anyway) Source Is the the Source on the internal network (one of the private IPs?), a public IP I want to masquerade as, or something else entirely? Destination Is this a place on the Internet (eg, "Only do this for the Site Google.com"/IP) or am I allowing myself to become confused again? Service I'm assuming this allows me to restrict which services this rule will apply to, but is it for a service on the internal network or a service being accessed on the external network? If I can offer any further details or information to make what I'm trying to do more clear, I will happily do so. Honestly any kind of help here would be very appreciated. I'm not a NetOps or anything even close, I spend most of my day writing code and my entire "team" at this company consists of "me, myself, and I" so while I try to broaden my KB at every possible opportunity, I can only learn so much, so fast and I feel like with networking especially there's just so much, coupled with a learning curve for each solution that likes to (from my limited perspective) use slightly different terminology that what I'm used to (and I don't exactly have the necessary experience to cross reference this stuff with the stuff I already know in context).

  Read the article

• Outbound traffic being blocked for MIP/VIPped servers (Juniper SSG5)

  - by Mark S. Rasmussen

  As we've been having some problems with sporadic packet loss, I've been preparing a replacement router (also an SSG5) for our current Juniper SSG5. I've setup the new SSG5 identically to the old one. We have a /29 IP range with a single IP setup as a MIP map to a server and two others being used for VIP maps. Each VIP/MIP is accompanied by relevant policies. Long story short - we tried connected the new SSG5 and some things were not working as they should. No problem, I just reconnected the old one. However, some things are still broken, even when I reconnected the old one. I fear I may have inadvertently changed some settings while browsing through old settings in my attempt to reconfigure the new SSG5 unit. All inbound traffic seems to work as expected. However, the 192.168.2.202 server can't initiate any outbound connections. It works perfectly on the local network, but any pings or DNS lookups to external IP's fail. The MIP & VIP map to it works perfectly - I can access it through HTTP and RDP without issues. Any tips on what to debug, or where I've messed up my config? I've attached the full config here (with anonymized IPs): set clock timezone 1 set vrouter trust-vr sharable set vrouter "untrust-vr" exit set vrouter "trust-vr" unset auto-route-export exit set service "MyVOIP_UDP4569" protocol udp src-port 0-65535 dst-port 4569-4569 set service "MyVOIP_TCP22" protocol tcp src-port 0-65535 dst-port 22-22 set service "MyRDP" protocol tcp src-port 0-65535 dst-port 3389-3389 set service "MyRsync" protocol tcp src-port 0-65535 dst-port 873-873 set service "NZ_FTP" protocol tcp src-port 0-65535 dst-port 40000-41000 set service "NZ_FTP" + tcp src-port 0-65535 dst-port 21-21 set service "PPTP-VPN" protocol 47 src-port 2048-2048 dst-port 2048-2048 set service "PPTP-VPN" + tcp src-port 1024-65535 dst-port 1723-1723 set service "NZ_FMS_1935" protocol tcp src-port 0-65535 dst-port 1935-1935 set service "NZ_FMS_1935" + udp src-port 0-65535 dst-port 1935-1935 set service "NZ_FMS_8080" protocol tcp src-port 0-65535 dst-port 8080-8080 set service "CrashPlan Server" protocol tcp src-port 0-65535 dst-port 4280-4280 set service "CrashPlan Console" protocol tcp src-port 0-65535 dst-port 4282-4282 unset alg sip enable set auth-server "Local" id 0 set auth-server "Local" server-name "Local" set auth default auth server "Local" set auth radius accounting port 1646 set admin auth timeout 10 set admin auth server "Local" set admin format dos set vip multi-port set zone "Trust" vrouter "trust-vr" set zone "Untrust" vrouter "trust-vr" set zone "DMZ" vrouter "trust-vr" set zone "VLAN" vrouter "trust-vr" set zone "Untrust-Tun" vrouter "trust-vr" set zone "Trust" tcp-rst set zone "Untrust" block unset zone "Untrust" tcp-rst set zone "DMZ" tcp-rst set zone "VLAN" block unset zone "VLAN" tcp-rst set zone "Untrust" screen tear-drop set zone "Untrust" screen syn-flood set zone "Untrust" screen ping-death set zone "Untrust" screen ip-filter-src set zone "Untrust" screen land set zone "V1-Untrust" screen tear-drop set zone "V1-Untrust" screen syn-flood set zone "V1-Untrust" screen ping-death set zone "V1-Untrust" screen ip-filter-src set zone "V1-Untrust" screen land set interface ethernet0/0 phy full 100mb set interface ethernet0/3 phy full 100mb set interface ethernet0/4 phy full 100mb set interface ethernet0/5 phy full 100mb set interface ethernet0/6 phy full 100mb set interface "ethernet0/0" zone "Untrust" set interface "ethernet0/1" zone "Null" set interface "bgroup0" zone "Trust" set interface "bgroup1" zone "Trust" set interface "bgroup2" zone "Trust" set interface bgroup2 port ethernet0/2 set interface bgroup0 port ethernet0/3 set interface bgroup0 port ethernet0/4 set interface bgroup1 port ethernet0/5 set interface bgroup1 port ethernet0/6 unset interface vlan1 ip set interface ethernet0/0 ip 212.242.193.18/29 set interface ethernet0/0 route set interface bgroup0 ip 192.168.1.1/24 set interface bgroup0 nat set interface bgroup1 ip 192.168.2.1/24 set interface bgroup1 nat set interface bgroup2 ip 192.168.3.1/24 set interface bgroup2 nat set interface ethernet0/0 gateway 212.242.193.17 unset interface vlan1 bypass-others-ipsec unset interface vlan1 bypass-non-ip set interface ethernet0/0 ip manageable set interface bgroup0 ip manageable set interface bgroup1 ip manageable set interface bgroup2 ip manageable set interface bgroup0 manage mtrace unset interface bgroup1 manage ssh unset interface bgroup1 manage telnet unset interface bgroup1 manage snmp unset interface bgroup1 manage ssl unset interface bgroup1 manage web unset interface bgroup2 manage ssh unset interface bgroup2 manage telnet unset interface bgroup2 manage snmp unset interface bgroup2 manage ssl unset interface bgroup2 manage web set interface ethernet0/0 vip 212.242.193.19 2048 "PPTP-VPN" 192.168.1.131 set interface ethernet0/0 vip 212.242.193.19 + 4280 "CrashPlan Server" 192.168.1.131 set interface ethernet0/0 vip 212.242.193.19 + 4282 "CrashPlan Console" 192.168.1.131 set interface ethernet0/0 vip 212.242.193.22 22 "MyVOIP_TCP22" 192.168.2.127 set interface ethernet0/0 vip 212.242.193.22 + 4569 "MyVOIP_UDP4569" 192.168.2.127 set interface ethernet0/0 vip 212.242.193.22 + 3389 "MyRDP" 192.168.2.202 set interface ethernet0/0 vip 212.242.193.22 + 873 "MyRsync" 192.168.2.201 set interface ethernet0/0 vip 212.242.193.22 + 80 "HTTP" 192.168.2.202 set interface ethernet0/0 vip 212.242.193.22 + 2048 "PPTP-VPN" 192.168.2.201 set interface ethernet0/0 vip 212.242.193.22 + 8080 "NZ_FMS_8080" 192.168.2.216 set interface ethernet0/0 vip 212.242.193.22 + 1935 "NZ_FMS_1935" 192.168.2.216 set interface bgroup0 dhcp server service set interface bgroup1 dhcp server service set interface bgroup2 dhcp server service set interface bgroup0 dhcp server auto set interface bgroup1 dhcp server auto set interface bgroup2 dhcp server auto set interface bgroup0 dhcp server option domainname iplan set interface bgroup0 dhcp server option dns1 192.168.1.131 set interface bgroup1 dhcp server option domainname nzlan set interface bgroup1 dhcp server option dns1 192.168.2.202 set interface bgroup2 dhcp server option dns1 8.8.8.8 set interface bgroup2 dhcp server option wins1 8.8.4.4 set interface bgroup0 dhcp server ip 192.168.1.2 to 192.168.1.116 set interface bgroup1 dhcp server ip 192.168.2.2 to 192.168.2.116 set interface bgroup2 dhcp server ip 192.168.3.2 to 192.168.3.126 unset interface bgroup0 dhcp server config next-server-ip unset interface bgroup1 dhcp server config next-server-ip unset interface bgroup2 dhcp server config next-server-ip set interface "ethernet0/0" mip 212.242.193.21 host 192.168.2.202 netmask 255.255.255.255 vr "trust-vr" set interface "serial0/0" modem settings "USR" init "AT&F" set interface "serial0/0" modem settings "USR" active set interface "serial0/0" modem speed 115200 set interface "serial0/0" modem retry 3 set interface "serial0/0" modem interval 10 set interface "serial0/0" modem idle-time 10 set pak-poll p1queue pak-threshold 96 set pak-poll p2queue pak-threshold 32 set flow tcp-mss unset flow tcp-syn-check set dns host dns1 0.0.0.0 set dns host dns2 0.0.0.0 set dns host dns3 0.0.0.0 set address "Trust" "192.168.1.0/24" 192.168.1.0 255.255.255.0 set address "Trust" "192.168.2.0/24" 192.168.2.0 255.255.255.0 set address "Trust" "192.168.3.0/24" 192.168.3.0 255.255.255.0 set ike respond-bad-spi 1 unset ike ikeid-enumeration unset ike dos-protection unset ipsec access-session enable set ipsec access-session maximum 5000 set ipsec access-session upper-threshold 0 set ipsec access-session lower-threshold 0 set ipsec access-session dead-p2-sa-timeout 0 unset ipsec access-session log-error unset ipsec access-session info-exch-connected unset ipsec access-session use-error-log set l2tp default ppp-auth chap set url protocol websense exit set policy id 1 from "Trust" to "Untrust" "Any" "Any" "ANY" permit traffic set policy id 1 exit set policy id 2 from "Untrust" to "Trust" "Any" "VIP(212.242.193.19)" "PPTP-VPN" permit traffic set policy id 2 exit set policy id 3 from "Untrust" to "Trust" "Any" "VIP(212.242.193.22)" "HTTP" permit traffic priority 0 set policy id 3 set service "MyRDP" set service "MyRsync" set service "MyVOIP_TCP22" set service "MyVOIP_UDP4569" exit set policy id 6 from "Trust" to "Trust" "192.168.1.0/24" "192.168.2.0/24" "ANY" deny set policy id 6 exit set policy id 7 from "Trust" to "Trust" "192.168.2.0/24" "192.168.1.0/24" "ANY" deny set policy id 7 exit set policy id 8 from "Trust" to "Trust" "192.168.3.0/24" "192.168.1.0/24" "ANY" deny set policy id 8 exit set policy id 9 from "Trust" to "Trust" "192.168.3.0/24" "192.168.2.0/24" "ANY" deny set policy id 9 exit set policy id 10 from "Untrust" to "Trust" "Any" "MIP(212.242.193.21)" "NZ_FTP" permit set policy id 10 exit set policy id 11 from "Untrust" to "Trust" "Any" "VIP(212.242.193.22)" "PPTP-VPN" permit set policy id 11 exit set policy id 12 from "Untrust" to "Trust" "Any" "VIP(212.242.193.22)" "NZ_FMS_1935" permit set policy id 12 set service "NZ_FMS_8080" exit set policy id 13 from "Untrust" to "Trust" "Any" "VIP(212.242.193.19)" "CrashPlan Console" permit set policy id 13 set service "CrashPlan Server" exit set nsmgmt bulkcli reboot-timeout 60 set ssh version v2 set config lock timeout 5 set snmp port listen 161 set snmp port trap 162 set vrouter "untrust-vr" exit set vrouter "trust-vr" unset add-default-route exit set vrouter "untrust-vr" exit set vrouter "trust-vr" exit

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >