Search Results

Search found 10489 results on 420 pages for 'usb keyboard'.

Page 2/420 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• PS/2 to USB adapter doesn't work with Model M keyboard

  - by mickburkejnr

  I bought a server about 3 months ago from a friend, and I have only had time to tinker with it in the last week. I noticed that this server doesn't have any PS/2 ports, which meant configuring it was near impossible. I don't have any USB keyboards in the house, I only have an IBM Model M keyboard (built 1994) and another IBM keyboard that was built circa 2001. Both of them have PS/2 connections. I bought an adapter off eBay, and when I used it with the Model M keyboard the three lights on the keyboard flashed for a split second, but then the keyboard is then unresponsive. I can bash away at the keys for ages and nothing will happen. The same applies to the later built IBM keyboard. What could I do to make the adapter work? I am getting the loan of a USB keyboard in two weeks time, but I'd like a more permanent solution without having to rely on getting the loan of a keyboard every time I have to perform maintenance on the server. And as I already have two keyboards which work fine and I like using, I don't really want to have to buy another keyboard just for use on the server.

  Read the article

• composite-video-to-usb adaptor

  - by sawa

  I bought a composite-video-to-usb adaptor. I want to stream video game in ubuntu. How can I do that? My environment: Monoprice USB Video and Audio Grabber Ubuntu 11.04 The relevant output of lsusb: Bus 001 Device 011: ID 0572:262a Conexant Systems (Rockwell), Inc. The relevant output of sudo lshw: *-usb:0 description: USB Controller product: 82801JI (ICH10 Family) USB UHCI Controller #4 vendor: Intel Corporation physical id: 1a bus info: pci@0000:00:1a.0 version: 00 width: 32 bits clock: 33MHz capabilities: uhci bus_master cap_list configuration: driver=uhci_hcd latency=0 resources: irq:16 ioport:f0e0(size=32) *-usb:1 description: USB Controller product: 82801JI (ICH10 Family) USB UHCI Controller #5 vendor: Intel Corporation physical id: 1a.1 bus info: pci@0000:00:1a.1 version: 00 width: 32 bits clock: 33MHz capabilities: uhci bus_master cap_list configuration: driver=uhci_hcd latency=0 resources: irq:21 ioport:f0c0(size=32) *-usb:2 description: USB Controller product: 82801JI (ICH10 Family) USB UHCI Controller #6 vendor: Intel Corporation physical id: 1a.2 bus info: pci@0000:00:1a.2 version: 00 width: 32 bits clock: 33MHz capabilities: uhci bus_master cap_list configuration: driver=uhci_hcd latency=0 resources: irq:18 ioport:f0a0(size=32) *-usb:3 description: USB Controller product: 82801JI (ICH10 Family) USB2 EHCI Controller #2 vendor: Intel Corporation physical id: 1a.7 bus info: pci@0000:00:1a.7 version: 00 width: 32 bits clock: 33MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci_hcd latency=0 resources: irq:18 memory:e0525c00-e0525fff *-multimedia description: Audio device product: 82801JI (ICH10 Family) HD Audio Controller vendor: Intel Corporation physical id: 1b bus info: pci@0000:00:1b.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=HDA Intel latency=0 resources: irq:43 memory:e0520000-e0523fff *-usb:4 description: USB Controller product: 82801JI (ICH10 Family) USB UHCI Controller #1 vendor: Intel Corporation physical id: 1d bus info: pci@0000:00:1d.0 version: 00 width: 32 bits clock: 33MHz capabilities: uhci bus_master cap_list configuration: driver=uhci_hcd latency=0 resources: irq:23 ioport:f080(size=32) *-usb:5 description: USB Controller product: 82801JI (ICH10 Family) USB UHCI Controller #2 vendor: Intel Corporation physical id: 1d.1 bus info: pci@0000:00:1d.1 version: 00 width: 32 bits clock: 33MHz capabilities: uhci bus_master cap_list configuration: driver=uhci_hcd latency=0 resources: irq:19 ioport:f060(size=32) *-usb:6 description: USB Controller product: 82801JI (ICH10 Family) USB UHCI Controller #3 vendor: Intel Corporation physical id: 1d.2 bus info: pci@0000:00:1d.2 version: 00 width: 32 bits clock: 33MHz capabilities: uhci bus_master cap_list configuration: driver=uhci_hcd latency=0 resources: irq:18 ioport:f040(size=32) *-usb:7 description: USB Controller product: 82801JI (ICH10 Family) USB2 EHCI Controller #1 vendor: Intel Corporation physical id: 1d.7 bus info: pci@0000:00:1d.7 version: 00 width: 32 bits clock: 33MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci_hcd latency=0 resources: irq:23 memory:e0525800-e0525bff The relevant output of dmesg: [18953.220035] usb 1-1: new high speed USB device using ehci_hcd and address 6 [19964.761076] Linux video capture interface: v2.00 [19964.767112] usbcore: registered new interface driver uvcvideo [19964.767115] USB Video Class driver (v1.0.0)

  Read the article

• ubuntu 13.04 recognizes usb mobile broadband modem as ethernet connection

  - by Bence Mihalka

  When I plug in my usb mobile broadband modem (ZTE MF-667), in the network manager instead of a mobile broadband connection, I get an ethernet connection, called: Ethernet Network (ZTE WCDMA Technologies MSM), which of course doesn't work. Here is my lsusb output and the relevant parts of dmesg output: lsusb: Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 003: ID 0cf3:3005 Atheros Communications, Inc. AR3011 Bluetooth Bus 001 Device 004: ID 04f2:b1b9 Chicony Electronics Co., Ltd Asus Integrated Webcam Bus 001 Device 005: ID 058f:6366 Alcor Micro Corp. Multi Flash Reader Bus 002 Device 004: ID 19d2:1405 ZTE WCDMA Technologies MSM dmesg: [ 195.328467] usb 2-1.1: new high-speed USB device number 3 using ehci-pci [ 195.423545] usb 2-1.1: New USB device found, idVendor=19d2, idProduct=1225 [ 195.423555] usb 2-1.1: New USB device strings: Mfr=3, Product=2, SerialNumber=4 [ 195.423561] usb 2-1.1: Product: ZTE WCDMA Technologies MSM [ 195.423567] usb 2-1.1: Manufacturer: ZTE,Incorporated [ 195.423572] usb 2-1.1: SerialNumber: P680A1ZTED000000 [ 195.426319] scsi7 : usb-storage 2-1.1:1.0 [ 196.425354] scsi 7:0:0:0: CD-ROM CWID USB SCSI CD-ROM 2.31 PQ: 0 ANSI: 2 [ 197.447919] usb 2-1.1: USB disconnect, device number 3 [ 197.457582] sr0: scsi3-mmc drive: 243x/186x xa/form2 cdda pop-up [ 197.457594] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 197.459058] sr 7:0:0:0: Attached scsi CD-ROM sr0 [ 197.459483] sr 7:0:0:0: Attached scsi generic sg2 type 5 [ 197.759186] usb 2-1.1: new high-speed USB device number 4 using ehci-pci [ 197.854543] usb 2-1.1: New USB device found, idVendor=19d2, idProduct=1405 [ 197.854556] usb 2-1.1: New USB device strings: Mfr=4, Product=3, SerialNumber=5 [ 197.854564] usb 2-1.1: Product: ZTE WCDMA Technologies MSM [ 197.854572] usb 2-1.1: Manufacturer: ZTE,Incorporated [ 197.854579] usb 2-1.1: SerialNumber: P680A1ZTED010000 [ 197.957739] scsi8 : usb-storage 2-1.1:1.2 [ 198.076554] cdc_ether 2-1.1:1.0 eth1: register 'cdc_ether' at usb-0000:00:1d.0-1.1, CDC Ethernet Device, 00:a0:c6:00:00:00 [ 198.076583] usbcore: registered new interface driver cdc_ether [ 198.955985] scsi 8:0:0:0: CD-ROM CWID USB SCSI CD-ROM 2.31 PQ: 0 ANSI: 2 [ 198.956797] scsi 8:0:0:1: Direct-Access ZTE MMC Storage 2.31 PQ: 0 ANSI: 2 I created the appropriate mobile broadband connection manually, but I cannot enable it in network manager, since the device is not recognized as mobile broadband. Any tips how to make it work?

  Read the article

• How to share two keyboard on the same laptop, french iso layout and usa ansi layout keyboard with usb?

  - by reyman64

  I recently buy a "noppoo choc mini" with this specific ANSI US-INTERNATIONAL pc84 layout. This specific keyboard have only 84 key , a 60% (compact tenkeyless) reduced layout My problem is simple, there is no keyboard layout into Ubuntu 12.04 which correspond to this usa normal ansi layout ... so it's the same problem with reduced version and only 84 key .. I search a template of normal ANSI US-INTERNATIONAL for xmodmap/xkb, and after i can try to manually map the other key. I search on google, and i don't find any other user which have same problem, so it's seem i have not the good keywoard to search this information.. Edit 1 : Here you can see there is probably a bug in ubuntu, because the layout for USA with dead key is not correct ! I have this : http://minus.com/lEdKMrsNAwkVA And other users have this for the same layout : http://i.stack.imgur.com/p52XG.png EDIT 2 It seems after a "sudo dpkg-reconfigure keyboard-configuration" : french standard keyboard pc105 + precision M65 keyboard from dell laptop Now i can see the good us layout in parameters, but i cannot have the iso layout for french usage... EDIT 3 Ok, after reboot i understand the probleme, i explain. I have one laptop with integrated french keyboard, and i want to use my usb keyboard which use a usa ANSI layout. It seem it's impossible in ubuntu and "dpkg-reconfigure keyboard-configuration" to share two different physical layout (ANSI and EU ISO) on the same computer ... EDIT4 Ok, it seems i can switch the physical layout (ISO <- ANSI) with this command in terminal : setxkbmap -layout us setxkbmap -layout us -variant alt-intl an setxkbmap -layout fr It's very complicated qnd it seem ubuntu 12.04 have big problem with keyboard manager ... because all works great with these two commands, without ANY change into the system parameters keyboard !!! Second bug ? The image of the layout for fr is buggy, the layout is not ISO, but i can press on the letter "< " at the left of right shift without any problem ! You can see the image here (french alternative with ANSI layout ? it's crazy ?) : http: //minus.com/lXsDJwoeyWAfF Can you help me on this point ? I'm lost with xkb, and manual mapping is very complicated ... Thanks a lot, SR

  Read the article

• Error in installing ZTE AC2738 on ubuntu 3.0.0-12-generic

  - by Netro

  I am getting this error ,struct usb_serial_driver has no member named shutdown. I am installing on 64bit ubuntu 3.0.0-12-generic ... Beginning Verify CD ... ... Verify CD Succeed! ... Beginning Copy Install Package Files ... ... will take a long time, waiting 5 seconds, please ... Copy Install Package Files Succeed! ... 'ztemtApp' previous version not found. and install now Beginning install ... ... Current linux release version is 'Ubuntu' ... Checking 'App' process ... Checking old installation ... Installing ... Current Path is : . : /tmp/ztemt_datacard/Linux 1. Checking Previous Version ... 2. Copying Data Bin ... ... will take a few seconds, please waiting ... /tmp/ztemt_datacard/Linux 3. Auto Load Usb Driver Module ... Rather than invoking init scripts through /etc/init.d, use the service(8) utility, e.g. service acpid restart Since the script you are attempting to invoke has been converted to an Upstart job, you may also use the stop(8) and then start(8) utilities, e.g. stop acpid ; start acpid. The restart(8) utility is also available. acpid stop/waiting acpid start/running, process 11802 4. Changing pppd Options ... 5. Changing File Permission ... 6. Deleting Qt lib When Local QT Vertion > V4.4.0 ... ... Package 'libqtgui4' exist ... QT_VERSION = 4 7. Deleting process id file: EVDOApp.pid ... 8. Making USB Serial Driver Module : ztemt.ko ... ... will take a few seconds, please waiting ... make -C /lib/modules/3.0.0-12-generic/build M=/usr/local/bin/ztemtApp/zteusbserial/below2.6.27 modules make[1]: Entering directory `/usr/src/linux-headers-3.0.0-12-generic' CC [M] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.o /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c: In function ‘destroy_serial’: /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:159:14: error: ‘struct usb_serial_driver’ has no member named ‘shutdown’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:165:18: error: ‘struct usb_serial_port’ has no member named ‘open_count’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c: In function ‘serial_open’: /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:241:36: error: ‘struct usb_serial_port’ has no member named ‘mutex’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:246:8: error: ‘struct usb_serial_port’ has no member named ‘open_count’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:251:6: error: ‘struct usb_serial_port’ has no member named ‘tty’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:253:10: error: ‘struct usb_serial_port’ has no member named ‘open_count’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:265:3: warning: passing argument 1 of ‘serial->type->open’ from incompatible pointer type [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:265:3: note: expected ‘struct tty_struct *’ but argument is of type ‘struct usb_serial_port *’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:265:3: warning: passing argument 2 of ‘serial->type->open’ from incompatible pointer type [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:265:3: note: expected ‘struct usb_serial_port *’ but argument is of type ‘struct file *’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:270:20: error: ‘struct usb_serial_port’ has no member named ‘mutex’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:276:6: error: ‘struct usb_serial_port’ has no member named ‘open_count’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:278:6: error: ‘struct usb_serial_port’ has no member named ‘tty’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:279:20: error: ‘struct usb_serial_port’ has no member named ‘mutex’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c: In function ‘serial_close’: /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:355:18: error: ‘struct usb_serial_port’ has no member named ‘mutex’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:357:10: error: ‘struct usb_serial_port’ has no member named ‘open_count’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:358:21: error: ‘struct usb_serial_port’ has no member named ‘mutex’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:371:8: error: ‘struct usb_serial_port’ has no member named ‘open_count’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:372:10: error: ‘struct usb_serial_port’ has no member named ‘open_count’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:375:3: error: too many arguments to function ‘port->serial->type->close’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:377:11: error: ‘struct usb_serial_port’ has no member named ‘tty’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:378:12: error: ‘struct usb_serial_port’ has no member named ‘tty’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:379:9: error: ‘struct usb_serial_port’ has no member named ‘tty’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:380:8: error: ‘struct usb_serial_port’ has no member named ‘tty’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:386:20: error: ‘struct usb_serial_port’ has no member named ‘mutex’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c: In function ‘serial_write’: /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:407:11: error: ‘struct usb_serial_port’ has no member named ‘open_count’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:413:2: warning: passing argument 1 of ‘port->serial->type->write’ from incompatible pointer type [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:413:2: note: expected ‘struct tty_struct *’ but argument is of type ‘struct usb_serial_port *’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:413:2: warning: passing argument 2 of ‘port->serial->type->write’ from incompatible pointer type [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:413:2: note: expected ‘struct usb_serial_port *’ but argument is of type ‘const unsigned char *’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:413:2: warning: passing argument 3 of ‘port->serial->type->write’ makes pointer from integer without a cast [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:413:2: note: expected ‘const unsigned char *’ but argument is of type ‘int’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:413:2: error: too few arguments to function ‘port->serial->type->write’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c: In function ‘serial_write_room’: /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:429:11: error: ‘struct usb_serial_port’ has no member named ‘open_count’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:435:2: warning: passing argument 1 of ‘port->serial->type->write_room’ from incompatible pointer type [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:435:2: note: expected ‘struct tty_struct *’ but argument is of type ‘struct usb_serial_port *’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c: In function ‘serial_chars_in_buffer’: /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:451:11: error: ‘struct usb_serial_port’ has no member named ‘open_count’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:457:2: warning: passing argument 1 of ‘port->serial->type->chars_in_buffer’ from incompatible pointer type [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:457:2: note: expected ‘struct tty_struct *’ but argument is of type ‘struct usb_serial_port *’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c: In function ‘serial_throttle’: /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:472:11: error: ‘struct usb_serial_port’ has no member named ‘open_count’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:479:3: warning: passing argument 1 of ‘port->serial->type->throttle’ from incompatible pointer type [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:479:3: note: expected ‘struct tty_struct *’ but argument is of type ‘struct usb_serial_port *’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c: In function ‘serial_unthrottle’: /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:491:11: error: ‘struct usb_serial_port’ has no member named ‘open_count’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:498:3: warning: passing argument 1 of ‘port->serial->type->unthrottle’ from incompatible pointer type [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:498:3: note: expected ‘struct tty_struct *’ but argument is of type ‘struct usb_serial_port *’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c: In function ‘serial_ioctl’: /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:511:11: error: ‘struct usb_serial_port’ has no member named ‘open_count’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:518:3: warning: passing argument 1 of ‘port->serial->type->ioctl’ from incompatible pointer type [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:518:3: note: expected ‘struct tty_struct *’ but argument is of type ‘struct usb_serial_port *’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:518:3: warning: passing argument 2 of ‘port->serial->type->ioctl’ makes integer from pointer without a cast [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:518:3: note: expected ‘unsigned int’ but argument is of type ‘struct file *’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:518:3: error: too many arguments to function ‘port->serial->type->ioctl’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c: In function ‘serial_set_termios’: /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:535:11: error: ‘struct usb_serial_port’ has no member named ‘open_count’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:542:3: warning: passing argument 1 of ‘port->serial->type->set_termios’ from incompatible pointer type [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:542:3: note: expected ‘struct tty_struct *’ but argument is of type ‘struct usb_serial_port *’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:542:3: warning: passing argument 2 of ‘port->serial->type->set_termios’ from incompatible pointer type [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:542:3: note: expected ‘struct usb_serial_port *’ but argument is of type ‘struct termios *’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:542:3: error: too few arguments to function ‘port->serial->type->set_termios’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c: In function ‘serial_break’: /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:554:11: error: ‘struct usb_serial_port’ has no member named ‘open_count’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:561:3: warning: passing argument 1 of ‘port->serial->type->break_ctl’ from incompatible pointer type [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:561:3: note: expected ‘struct tty_struct *’ but argument is of type ‘struct usb_serial_port *’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c: In function ‘serial_tiocmget’: /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:629:11: error: ‘struct usb_serial_port’ has no member named ‘open_count’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:635:3: warning: passing argument 1 of ‘port->serial->type->tiocmget’ from incompatible pointer type [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:635:3: note: expected ‘struct tty_struct *’ but argument is of type ‘struct usb_serial_port *’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:635:3: error: too many arguments to function ‘port->serial->type->tiocmget’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c: In function ‘serial_tiocmset’: /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:651:11: error: ‘struct usb_serial_port’ has no member named ‘open_count’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:657:3: warning: passing argument 1 of ‘port->serial->type->tiocmset’ from incompatible pointer type [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:657:3: note: expected ‘struct tty_struct *’ but argument is of type ‘struct usb_serial_port *’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:657:3: warning: passing argument 2 of ‘port->serial->type->tiocmset’ makes integer from pointer without a cast [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:657:3: note: expected ‘unsigned int’ but argument is of type ‘struct file *’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:657:3: error: too many arguments to function ‘port->serial->type->tiocmset’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c: In function ‘usb_serial_port_work’: /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:697:12: error: ‘struct usb_serial_port’ has no member named ‘tty’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c: In function ‘port_release’: /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:709:2: error: ‘struct device’ has no member named ‘bus_id’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c: In function ‘usb_serial_probe’: /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:858:2: error: implicit declaration of function ‘lock_kernel’ [-Werror=implicit-function-declaration] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:861:3: error: implicit declaration of function ‘unlock_kernel’ [-Werror=implicit-function-declaration] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1034:3: error: ‘struct usb_serial_port’ has no member named ‘mutex’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1182:23: error: ‘struct device’ has no member named ‘bus_id’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1182:51: error: ‘struct device’ has no member named ‘bus_id’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1183:3: error: ‘struct device’ has no member named ‘bus_id’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c: In function ‘usb_serial_disconnect’: /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1257:13: error: ‘struct usb_serial_port’ has no member named ‘tty’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1258:21: error: ‘struct usb_serial_port’ has no member named ‘tty’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c: At top level: /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1280:2: warning: initialization from incompatible pointer type [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1280:2: warning: (near initialization for ‘serial_ops.ioctl’) [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1281:2: warning: initialization from incompatible pointer type [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1281:2: warning: (near initialization for ‘serial_ops.set_termios’) [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1284:2: warning: initialization from incompatible pointer type [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1284:2: warning: (near initialization for ‘serial_ops.break_ctl’) [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1286:2: error: unknown field ‘read_proc’ specified in initializer /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1286:2: warning: initialization from incompatible pointer type [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1286:2: warning: (near initialization for ‘serial_ops.ioctl’) [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1287:2: warning: initialization from incompatible pointer type [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1287:2: warning: (near initialization for ‘serial_ops.tiocmget’) [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1288:2: warning: initialization from incompatible pointer type [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1288:2: warning: (near initialization for ‘serial_ops.tiocmset’) [enabled by default] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c: In function ‘usb_serial_init’: /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1352:2: error: implicit declaration of function ‘info’ [-Werror=implicit-function-declaration] /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c: In function ‘fixup_generic’: /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1406:2: error: ‘struct usb_serial_driver’ has no member named ‘shutdown’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1406:2: error: ‘struct usb_serial_driver’ has no member named ‘shutdown’ /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1406:1: error: ‘usb_serial_generic_shutdown’ undeclared (first use in this function) /usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.c:1406:1: note: each undeclared identifier is reported only once for each function it appears in cc1: some warnings being treated as errors make[2]: *** [/usr/local/bin/ztemtApp/zteusbserial/below2.6.27/usb-serial.o] Error 1 make[1]: *** [_module_/usr/local/bin/ztemtApp/zteusbserial/below2.6.27] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-3.0.0-12-generic' make: *** [modules] Error 2 Install finished! Any suggestion? Update: from installation document , In some special cases, the setup package can’t automatically compile the driver, so you need change the configurations yourself and manually compile the driver. Method: enter the directory: /usr/local/bin/ztemtApp/zteusbserial, and find the corresponding kernel version of current system. I can see 2.6.27 2.6.28 2.6.29 2.6.30 2.6.31 2.6.32 2.6.33 2.6.34 2.6.35 2.6.36 2.6.37 2.6.38 2.6.39 below2.6.2 in the directory. Which version shall I pick up for installation? Readme file says, we have to do this to insert ztemt.ko in kernel.

  Read the article

• External USB attached drive works in Windows XP but not in Windows 7. How to fix?

  - by irrational John

  Earlier this week I purchased this "N52300 EZQuest Pro" external hard drive enclosure from here. I can connect the enclosure using USB 2.0 and access the files in both NTFS partitions on the MBR partitioned drive when I use either Windows XP (SP3) or Mac OS X 10.6. So it works as expected in XP & Snow Leopard. However, the enclosure does not work in Windows 7 (Home Premium) either 64-bit or 32-bit or in Ubuntu 10.04 (kernel 2.6.32-23-generic). I'm thinking this must be a Windows 7 driver problem because the enclosure works in XP & Snow Leopard. I do know that no special drivers are required to use this enclosure. It is supported using the USB mass storage drivers included with XP and OS X. It should also work fine using the mass storage support in Windows 7, no? FWIW, I have also tried using 32-bit Windows 7 on both my desktop, a Gigabyte GA-965P-DS3 with a Pentium Dual-Core E6500 @ 2.93GHz, and on my early 2008 MacBook. I see the same failure in both cases that I see with 64-bit Windows 7. So it doesn't appear to be specific to one hardware platform. I'm hoping someone out there can help me either get the enclosure to work in Windows 7 or convince me that the enclosure hardware is bad and should be RMAed. At the moment though an RMA seems pointless since this appears to be a (Windows 7) device driver problem. I have tried to track down any updates to the mass storage drivers included with Windows 7 but have so far come up empty. Heck, I can't even figure out how to place a bug report with Microsoft since apparently the grace period for Windows 7 email support is only a few months. I came across a link to some USB troubleshooting steps in another question. I haven't had a chance to look over the suggestions on that site or try them yet. Maybe tomorrow if I have time ... ;-) I'll finish up with some more details about the problem. When I connect the enclosure using USB to Windows 7 at first it appears everything worked. Windows detects the drive and installs a driver for it. Looking in Device Manager there is an entry under the Hard Drives section with the title, Hitachi HDT721010SLA360 USB Device. When you open Windows Disk Management the first time after the enclosure has been attached the drive appears as "Not initialize" and I'm prompted to initialize it. This is bogus. After all, the drive worked fine in XP so I know it has already been initialized, partitioned, and formatted. So of course I never try to initialize it "again". (It's a 1 GB drive and I don't want to lose the data on it). Except for this first time, the drive never shows up in Disk Management again unless I uninstall the Hitachi HDT721010SLA360 USB Device entry under Hard Drives, unplug, and then replug the enclosure. If I do that then the process in the previous paragraph repeats. In Ubuntu the enclosure never shows up at all at the file system level. Below are an excerpt from kern.log and an excerpt from the result of lsusb -v after attaching the enclosure. It appears that Ubuntu at first recongnizes the enclosure and is attempting to attach it, but encounters errors which prevent it from doing so. Unfortunately, I don't know whether any of this info is useful or not. excerpt from kern.log [ 2684.240015] usb 1-2: new high speed USB device using ehci_hcd and address 22 [ 2684.393618] usb 1-2: configuration #1 chosen from 1 choice [ 2684.395399] scsi17 : SCSI emulation for USB Mass Storage devices [ 2684.395570] usb-storage: device found at 22 [ 2684.395572] usb-storage: waiting for device to settle before scanning [ 2689.390412] usb-storage: device scan complete [ 2689.390894] scsi 17:0:0:0: Direct-Access Hitachi HDT721010SLA360 ST6O PQ: 0 ANSI: 4 [ 2689.392237] sd 17:0:0:0: Attached scsi generic sg7 type 0 [ 2689.395269] sd 17:0:0:0: [sde] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) [ 2689.395632] sd 17:0:0:0: [sde] Write Protect is off [ 2689.395636] sd 17:0:0:0: [sde] Mode Sense: 11 00 00 00 [ 2689.395639] sd 17:0:0:0: [sde] Assuming drive cache: write through [ 2689.412003] sd 17:0:0:0: [sde] Assuming drive cache: write through [ 2689.412009] sde: sde1 sde2 [ 2689.455759] sd 17:0:0:0: [sde] Assuming drive cache: write through [ 2689.455765] sd 17:0:0:0: [sde] Attached SCSI disk [ 2692.620017] usb 1-2: reset high speed USB device using ehci_hcd and address 22 [ 2707.740014] usb 1-2: device descriptor read/64, error -110 [ 2722.970103] usb 1-2: device descriptor read/64, error -110 [ 2723.200027] usb 1-2: reset high speed USB device using ehci_hcd and address 22 [ 2738.320019] usb 1-2: device descriptor read/64, error -110 [ 2753.550024] usb 1-2: device descriptor read/64, error -110 [ 2753.780020] usb 1-2: reset high speed USB device using ehci_hcd and address 22 [ 2758.810147] usb 1-2: device descriptor read/8, error -110 [ 2763.940142] usb 1-2: device descriptor read/8, error -110 [ 2764.170014] usb 1-2: reset high speed USB device using ehci_hcd and address 22 [ 2769.200141] usb 1-2: device descriptor read/8, error -110 [ 2774.330137] usb 1-2: device descriptor read/8, error -110 [ 2774.440069] usb 1-2: USB disconnect, address 22 [ 2774.440503] sd 17:0:0:0: Device offlined - not ready after error recovery [ 2774.590023] usb 1-2: new high speed USB device using ehci_hcd and address 23 [ 2789.710020] usb 1-2: device descriptor read/64, error -110 [ 2804.940020] usb 1-2: device descriptor read/64, error -110 [ 2805.170026] usb 1-2: new high speed USB device using ehci_hcd and address 24 [ 2820.290019] usb 1-2: device descriptor read/64, error -110 [ 2835.520027] usb 1-2: device descriptor read/64, error -110 [ 2835.750018] usb 1-2: new high speed USB device using ehci_hcd and address 25 [ 2840.780085] usb 1-2: device descriptor read/8, error -110 [ 2845.910079] usb 1-2: device descriptor read/8, error -110 [ 2846.140023] usb 1-2: new high speed USB device using ehci_hcd and address 26 [ 2851.170112] usb 1-2: device descriptor read/8, error -110 [ 2856.300077] usb 1-2: device descriptor read/8, error -110 [ 2856.410027] hub 1-0:1.0: unable to enumerate USB device on port 2 [ 2856.730033] usb 3-2: new full speed USB device using uhci_hcd and address 11 [ 2871.850017] usb 3-2: device descriptor read/64, error -110 [ 2887.080014] usb 3-2: device descriptor read/64, error -110 [ 2887.310011] usb 3-2: new full speed USB device using uhci_hcd and address 12 [ 2902.430021] usb 3-2: device descriptor read/64, error -110 [ 2917.660013] usb 3-2: device descriptor read/64, error -110 [ 2917.890016] usb 3-2: new full speed USB device using uhci_hcd and address 13 [ 2922.911623] usb 3-2: device descriptor read/8, error -110 [ 2928.051753] usb 3-2: device descriptor read/8, error -110 [ 2928.280013] usb 3-2: new full speed USB device using uhci_hcd and address 14 [ 2933.301876] usb 3-2: device descriptor read/8, error -110 [ 2938.431993] usb 3-2: device descriptor read/8, error -110 [ 2938.540073] hub 3-0:1.0: unable to enumerate USB device on port 2 excerpt from lsusb -v Bus 001 Device 017: ID 0dc4:0000 Macpower Peripherals, Ltd Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x0dc4 Macpower Peripherals, Ltd idProduct 0x0000 bcdDevice 0.01 iManufacturer 1 EZ QUEST iProduct 2 USB Mass Storage iSerial 3 220417 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 32 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 5 Config0 bmAttributes 0xc0 Self Powered MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 8 Mass Storage bInterfaceSubClass 6 SCSI bInterfaceProtocol 80 Bulk (Zip) iInterface 4 Interface0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x01 EP 1 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0001 Self Powered Update: Results using Firewire to connect. Today I recieved a 1394b 9 pin to 1394a 6 pin cable which allowed me to connect the "EZQuest Pro" via Firewire. Everything works. When I use Firewire I can connect whether I'm using Windows 7 or Ubuntu 10.04. I even tried booting my Gigabyte desktop as an OS X 10.6.3 Hackintosh and it worked there as well. (Though if I recall correctly, it also worked when using USB 2.0 and booting OS X on the desktop. Certainly it works with USB 2.0 and my MacBook.) I believe the firmware on the device is at the latest level available, v1.07. I base this on the excerpt below from the OS X System Profiler which shows Firmware Revision: 0x107. Bottom line: It's nice that the enclosure is actually usable when I connect with Firewire. But I am still searching for an answer as to why it does not work correctly when using USB 2.0 in Windows 7 (and Ubuntu ... but really Windows 7 is my biggest concern). OXFORD IDE Device 1: Manufacturer: EZ QUEST Model: 0x0 GUID: 0x1D202E0220417 Maximum Speed: Up to 800 Mb/sec Connection Speed: Up to 400 Mb/sec Sub-units: OXFORD IDE Device 1 Unit: Unit Software Version: 0x10483 Unit Spec ID: 0x609E Firmware Revision: 0x107 Product Revision Level: ST6O Sub-units: OXFORD IDE Device 1 SBP-LUN: Capacity: 1 TB (1,000,204,886,016 bytes) Removable Media: Yes BSD Name: disk3 Partition Map Type: MBR (Master Boot Record) S.M.A.R.T. status: Not Supported

  Read the article

• MP3 player mpman TS300 not recognized

  - by Nick Lemaire

  I just received a mpman ts300 mp3 player for Christmas. But when I try to connect it to ubuntu (10.10) through usb it doesn't seem to be recognized. I searched for a linuxdriver but came up with nothing. I even tried installing mpman manager from the software center, but still the same problem... Has anybody got any ideas about how to fix this? Thank you edit: some additional information When I plug it in, it doesn't show up under /dev. And it is not listed in the result of 'lsusb' This is the output of 'dmesg' [19571.732541] usb 1-4: new high speed USB device using ehci_hcd and address 2 [19571.889154] scsi7 : usb-storage 1-4:1.0 [19572.883155] scsi 7:0:0:0: Direct-Access TS300 USB DISK 1.00 PQ: 0 ANSI: 0 [19572.885856] sd 7:0:0:0: Attached scsi generic sg2 type 0 [19572.887266] sd 7:0:0:0: [sdb] 7868416 512-byte logical blocks: (4.02 GB/3.75 GiB) [19573.012547] usb 1-4: reset high speed USB device using ehci_hcd and address 2 [19573.292550] usb 1-4: reset high speed USB device using ehci_hcd and address 2 [19573.572565] usb 1-4: reset high speed USB device using ehci_hcd and address 2 [19573.725019] sd 7:0:0:0: [sdb] Test WP failed, assume Write Enabled [19573.725024] sd 7:0:0:0: [sdb] Assuming drive cache: write through [19573.728521] sd 7:0:0:0: [sdb] Attached SCSI removable disk [19575.333015] sd 7:0:0:0: [sdb] 7868416 512-byte logical blocks: (4.02 GB/3.75 GiB) [19575.452547] usb 1-4: reset high speed USB device using ehci_hcd and address 2 [19580.603253] usb 1-4: device descriptor read/all, error -110 [19580.722560] usb 1-4: reset high speed USB device using ehci_hcd and address 2 [19595.842579] usb 1-4: device descriptor read/64, error -110 [19611.072656] usb 1-4: device descriptor read/64, error -110 [19611.302540] usb 1-4: reset high speed USB device using ehci_hcd and address 2 [19616.332568] usb 1-4: device descriptor read/8, error -110 [19621.462692] usb 1-4: device descriptor read/8, error -110 [19621.692551] usb 1-4: reset high speed USB device using ehci_hcd and address 2 [19626.722567] usb 1-4: device descriptor read/8, error -110 [19631.852802] usb 1-4: device descriptor read/8, error -110 [19631.962587] usb 1-4: USB disconnect, address 2 [19631.962587] sd 7:0:0:0: Device offlined - not ready after error recovery [19631.962840] sd 7:0:0:0: [sdb] Assuming drive cache: write through [19631.965104] sd 7:0:0:0: [sdb] READ CAPACITY failed [19631.965109] sd 7:0:0:0: [sdb] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [19631.965112] sd 7:0:0:0: [sdb] Sense not available. [19631.965125] sd 7:0:0:0: [sdb] Assuming drive cache: write through [19631.965130] sdb: detected capacity change from 4028628992 to 0 [19632.130042] usb 1-4: new high speed USB device using ehci_hcd and address 3 [19647.242550] usb 1-4: device descriptor read/64, error -110 [19662.472560] usb 1-4: device descriptor read/64, error -110 [19662.702566] usb 1-4: new high speed USB device using ehci_hcd and address 4 [19677.822587] usb 1-4: device descriptor read/64, error -110 [19693.052575] usb 1-4: device descriptor read/64, error -110 [19693.282582] usb 1-4: new high speed USB device using ehci_hcd and address 5 [19698.312600] usb 1-4: device descriptor read/8, error -110 [19703.442594] usb 1-4: device descriptor read/8, error -110 [19703.672548] usb 1-4: new high speed USB device using ehci_hcd and address 6 [19708.702581] usb 1-4: device descriptor read/8, error -110 [19713.840077] usb 1-4: device descriptor read/8, error -110 [19713.942555] hub 1-0:1.0: unable to enumerate USB device on port 4 [19714.262545] usb 4-2: new full speed USB device using uhci_hcd and address 2 [19729.382549] usb 4-2: device descriptor read/64, error -110 [19744.612534] usb 4-2: device descriptor read/64, error -110 [19744.842543] usb 4-2: new full speed USB device using uhci_hcd and address 3 [19759.962714] usb 4-2: device descriptor read/64, error -110 [19775.200047] usb 4-2: device descriptor read/64, error -110 [19775.422630] usb 4-2: new full speed USB device using uhci_hcd and address 4 [19780.444498] usb 4-2: device descriptor read/8, error -110 [19785.574491] usb 4-2: device descriptor read/8, error -110 [19785.802547] usb 4-2: new full speed USB device using uhci_hcd and address 5 [19790.824490] usb 4-2: device descriptor read/8, error -110 [19795.961473] usb 4-2: device descriptor read/8, error -110 [19796.062556] hub 4-0:1.0: unable to enumerate USB device on port 2

  Read the article

• Separate keyboard shortcuts for switching between keyboard layouts

  - by Vitaliy

  I have a few language keyboard layouts installed in my Ubuntu 12.04. I am using ctrl-shift keyboard shortcut for switching between language layouts. Such switching method takes a lot of my time. Is there any posibility to set up a different keyboard shortcut for each language keyboard layout? For example: ctrl-shift-1 (english layout), ctrl-shift-2 (polish layout), ctrl-shift-3 (italian layout) etc.

  Read the article

• Determining speed (class) of USB on PC

  - by Thomas Matthews

  Is there a method for determining the speed of a USB port on a Windows XP PC, without using a USB protocol analyzer? I'm looking for something simple, such as looking at the Device Manager. I would like to hook up some USB equipment to a USB 2.0 port, rather than the slower USB 1.0 or 1.1.

  Read the article

• Problem with Numlock light and remapping keyboard

  - by ansidev

  I upgraded to Ubuntu 13.10. And there are two problem: Numlock is on. But after I press Ctrl+Space (hotkey for IBus, (default in 13.10 is Super+Space)), Numlock is off and I must press Numlock button twice to enable Numlock. About remapping keyboard, because my keyboard have some broken key, so I am using xmodmap to remap my keyboard (config file for xmodmap is $HOME/.xmodmap). But when I switch keyboard layout (I mentioned above), everything changed to default, and I must run xmodmap .xmodmap to remap keyboard again. When using Ubuntu 13.04, everything is good. How to solve my problems? UPDATE: 1. I am using two keyboard layout: English (US) and Unikey (from ibus-unikey package). 2. If I change key board layout using menu on Unity panel, no first problem.

  Read the article

• USB connection issue

  - by user1664417

  Currently Im facing an issue when Im trying to connect any usb flash drive to my pc. ok, below is what happens to me: 1) I can connect usb keyboard and mouse without any issue. 2) however when i connect usb flash drive, there are 2 situations that are occuring randomly a) there is no usb drive mount in my computer, when device manager is checked, it shows error code 10, but is shown in disk management. b) my computer will have usb drive mounted, but when I click on it, it is empty. on right click the properties, the disk space show 0. (there are files within the usb) what i have done is: 1) run CCleaner to repair the registry, restart and try, but still not working. 2) uninstall the drive in device manager, restart and try, but still not working. 3) tried the port that connects mouse and keyboard, but does not work. anyone who experienced these problems before please guide me. any suggestions or solutions would be greatly appreciated. Thanks, Tony

  Read the article

• How to Boot a VMware Virtual Machine from a USB Drive

  - by Usman

  Do you have an OS installed on your USB thumb drive? Booting from it in a VM is now possible, you’ll just have to use a simple trick to get it to work. Last week we showed you how to put Ubuntu on a USB drive in a separate partition, and we also discussed working with VMware Player (our favourite VM Client). But have you ever tried booting from a USB drive in VMWare? It doesn’t allow doing so, but we will force it to boot from a USB, with a bit of old geekery. If you remember, we have showed you how to boot from a USB drive even if your old PC doesn’t allow booting from one. That’s right, using Plop Boot Manager. All we need to do is to load the Plop ISO in VMware, attach and enable the USB drive in VMware, and finally select the USB option in Plop Boot Manager to boot from the USB. So, visit the Plop boot manager download site. HTG Explains: When Do You Need to Update Your Drivers? How to Make the Kindle Fire Silk Browser *Actually* Fast! Amazon’s New Kindle Fire Tablet: the How-To Geek Review

  Read the article

• Use Mobile Broadband USB as Wireless Adapter USB - HUAWEI E173

  - by Alex

  I have an Mobile Broadband USB (HUAWEI E173), which can also work as a WiFi Adapter USB. The problem is that Ubuntu 12.04 only recognizes it as an Mobile Broadband USB, not as an Wireless Adapter USB, is there a way to "trick" Ubuntu to recognize my USB as a Wireless Adapter? Thanks in advance. Notes: I used the lsusb command and got this: `Bus 002 Device 009: ID 12d1:1c23 Huawei Technologies Co., Ltd.` I have 64-bit Ubuntu Installed, so it may just be a driver problem.

  Read the article

• Stack-based keyboard delay using Logitech MX3100 keyboard

  - by Mark S. Rasmussen

  I've been using a Logitech Cordless Desktop MX3100 keyboard for quite a while. I've never really had any problems, except for the occasional typo. I noticed however that I tended make the typo "Laod" instead of "Load", quite a bit more often than any other typos. As it started to get on my nerves, I decided to do some testing. What I found out was than when I write lowercase "load", I'd never make the typo. All uppercase, or just uppercase L, I'd make the typo quite often. My actual (very scientific) testing is probably best described by showing the output: moatmoatmoat MoatMoatMoat loatloatloat LaotLaotLaot loafloafloaf LaofLaofLaof hoathoathoat HoatHoatHoat hoadhoadhoad HoadHoadHoad lortlortlort LrotLrotLrot What i found out was that whenever shift was depressed, typing an uppercase "L" would induce a significant lag if the next character was an "o", compared to the lag of the any other key: High "o" lag: LoLoLoLoLoLo No "a" lag: LaLaLaLaLaLa No lag for neither "o" nor "a": lolololololo lalalalalala By realizing this I regained a slight bit of sanity as I knew I wasn't coming down with a case of Parkinsons. I was actually typing correctly, the lag just interpreted it wrongly. Now, what really bugs me is that I can't fathom how this is occurring. What I'm actually typing, in physical order, is this: L - o - a - d, and yet, the "a" is output before the "o", even though "o" was pressed before "a". So while the keyboard is processing the "Lo" combo, the "a" gets prioritized and is inserted before the "o" is done processing, resulting in Laod instead of Load. And this only happens when typing "Lo", not when typing lowercase "lo". This problem could stem from the keyboard hardware, the receiver hardware or the keyboard software driver. No matter the fault location however, I can't imagine how this could be implemented as anything but a FIFO queue. A general delay, sure, I could live with that, albeit I'd be irritated. But a lag affecting different keys differently, and even resulting in unpredictable outcome - that just doesn't make any sense. I've solved the problem by just switching to a wired keyboard. I just can't shake it off me though; what kind of bug/error/scenario would result in a case like this? Edit: It's been suggested that I stop drinking Red Bull and stick to water instead. While that may actually help solve the issue, I'm really not looking for a solution as such. I'm more interested in an explanation of how this could happen, as I can't imagine any viable technical solution that could result in this behavior.

  Read the article

• Desktop keyboard behaves like laptop keyboard when numlock is on

  - by lstone

  I have fully updated ubuntu 12.04 installed on my desktop. The problem is when I turn on NumLock, the keyboard behaves like a laptop keyboard making the keys "mjkluio789" correspond to "0-9". I've had a laptop where such behavior was expected due to absence of a separate numpad. I'm using an iBall USB keyboard and it has a numpad section unlike laptop keyboards(http://iball.co.in/Product.aspx?c=2).

  Read the article

• USB-creator: Error erasing device: Unknown or unsupported erase type

  - by Mike Williamson

  I created a live usb using usb-creator-gtk. I installed Ubuntu with it and all was good with the world. Now I am trying to use the same memory stick and create a live USB for 14.04 and I get the following error when trying to erase the disk. org.freedesktop.DBus.Python.gi._glib.GError: Traceback (most recent call last): File "/usr/lib/python3/dist-packages/dbus/service.py", line 707, in _message_cb retval = candidate_method(self, *args, **keywords) File "/usr/share/usb-creator/usb-creator-helper", line 239, in Format block.call_format_sync('dos', GLib.Variant('a{sv}', {'erase': GLib.Variant('s', '')}), None) gi._glib.GError: GDBus.Error:org.freedesktop.UDisks2.Error.Failed: Error erasing device: Unknown or unsupported erase type `' How can I fix this so I can create a new live USB?

  Read the article

• How would the optimal Emacs-keyboard look like?

  - by Thorsten

  Emacs is a historic piece of software. It promises outstanding productivity for keyboard wizards that really want to explore it's power. The effective use of the keyboard is key to Emacs productivity, but the keyboard hardware has changed a lot since the old days, so many modern Emacs users are struggling with weird 'Emacs chords' on their Windows/IBM keyboards. If one would design a keyboard that is entirely focused on the needs of Emacs users - how would it look like? I assume the following: the standard keybindings of Emacs are accepted, redefinitions are rare exceptions we are only talking about QWERTY keyboards (including regional variations like QWERTZ) we are only considering users applying the (10 fingers) touch typing system. the question is not only about remapping the keys of existing keyboards (perfectly possible on Linux with .xmodmap and on Windows with keytweak, for example) - think about the perfect keyboard-hardware you would like to see on your desk while hacking in Emacs all day long. Please tag your answer with your locale, i.e. [en] or [de], so that everybody knows what regional layout you are using. I will answer my own question below, to show you the results of some investigation and experimentation, but I really would like to read about different approaches and their pro's and con's. The emacswiki has a somehow related page with a lot of links (http://www.emacswiki.org/emacs/RepeatedStrainInjury), but here it's about optimal keyboard design for maximal productivity, assuming avoidance of RSI as a byproduct.

  Read the article

• how to set keyboard for phonetic Hindi typing oneiric for Wx keyboard on QWERTY keyboard

  - by Registered User

  I am trying to type documents in Hindi language. My OS: Ubuntu 11.10 Gnome environment (http://packages.ubuntu.com/search?keywords=gnome-session-fallback) I do not use unity interface.The method is shown here http://www.youtube.com/watch?v=LL7icGNhIfI I am able to type in Hindi in Libreoffice and gedit as well with method shown above.But this is a very difficult way of typing because I have to remember all the English Keys corresponding to the Hindi words as mapped here http://docs.redhat.com/docs/en-US/Red_Hat_Enterprise_Linux/5/html-single/International_Language_Support_Guide/images/hindi.png What I want to be able to do is type phonetically and not use above kind of keyboard. I have US English keyboard in my laptop. See the snapshot here https://picasaweb.google.com/107404068162388981296/UnknownAsianLanguage#5704771437325752466 I have selected the phonetic input method in Ibus window but this still is not working as expected. I expect to be able to type phonetically (given with above phonetic selection) what is happening is I have to type like using a QWERTY keyboard for Hindi language which is deviation from expected behavior. How can I rectify or achieve correct behavior?

  Read the article

• Connect ps/2->usb keyboard to linux?

  - by Daniel

  I have a lovely ancient ergonomic keyboard (no name SK - 6000) connected via a DIN-ps/2 adapter to a ps/2-usb adapter to my docking station. After Grub it stops working. It takes either suspending and waking up or replugging it while Linux is running to get it to work. No extra kernel modules get loaded for this. When it works and I restart without power off, it will work immediately. Even when it does not work, it is visible (lsusb device number varies but output is identical whether working or not): $ lsusb -v -s 001:006 Bus 001 Device 006: ID 0a81:0205 Chesen Electronics Corp. PS/2 Keyboard+Mouse Adapter Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 8 idVendor 0x0a81 Chesen Electronics Corp. idProduct 0x0205 PS/2 Keyboard+Mouse Adapter bcdDevice 0.10 iManufacturer 1 CHESEN iProduct 2 PS2 to USB Converter iSerial 0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 59 bNumInterfaces 2 bConfigurationValue 1 iConfiguration 2 PS2 to USB Converter bmAttributes 0xa0 (Bus Powered) Remote Wakeup MaxPower 100mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 3 Human Interface Device bInterfaceSubClass 1 Boot Interface Subclass bInterfaceProtocol 1 Keyboard iInterface 0 HID Device Descriptor: bLength 9 bDescriptorType 33 bcdHID 1.10 bCountryCode 0 Not supported bNumDescriptors 1 bDescriptorType 34 Report wDescriptorLength 64 Report Descriptors: ** UNAVAILABLE ** Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0008 1x 8 bytes bInterval 10 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 1 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 3 Human Interface Device bInterfaceSubClass 1 Boot Interface Subclass bInterfaceProtocol 2 Mouse iInterface 0 HID Device Descriptor: bLength 9 bDescriptorType 33 bcdHID 1.10 bCountryCode 0 Not supported bNumDescriptors 1 bDescriptorType 34 Report wDescriptorLength 148 Report Descriptors: ** UNAVAILABLE ** Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0008 1x 8 bytes bInterval 10 Device Status: 0x0000 (Bus Powered) $ ll -R /sys/bus/hid/drivers/ /sys/bus/hid/drivers/: total 0 drwxr-xr-x 2 root root 0 Jul 8 2012 generic-usb/ /sys/bus/hid/drivers/generic-usb: total 0 lrwxrwxrwx 1 root root 0 Jul 7 23:33 0003:046D:C03D.0003 -> ../../../../devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2.2/1-1.2.2:1.0/0003:046D:C03D.0003/ lrwxrwxrwx 1 root root 0 Jul 7 23:33 0003:0A81:0205.0001 -> ../../../../devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2.1/1-1.2.1:1.0/0003:0A81:0205.0001/ lrwxrwxrwx 1 root root 0 Jul 7 23:33 0003:0A81:0205.0002 -> ../../../../devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2.1/1-1.2.1:1.1/0003:0A81:0205.0002/ --w------- 1 root root 4096 Jul 7 23:32 bind lrwxrwxrwx 1 root root 0 Jul 7 23:33 module -> ../../../../module/usbhid/ --w------- 1 root root 4096 Jul 7 23:32 new_id --w------- 1 root root 4096 Jul 8 2012 uevent --w------- 1 root root 4096 Jul 7 23:32 unbind When replugging, dmesg shows this (which except for the 1st line and different input numbers already came at boot time): [ 1583.295385] usb 1-1.2.1: new low-speed USB device number 6 using ehci_hcd [ 1583.446514] input: CHESEN PS2 to USB Converter as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2.1/1-1.2.1:1.0/input/input17 [ 1583.446817] generic-usb 0003:0A81:0205.0001: input,hidraw0: USB HID v1.10 Keyboard [CHESEN PS2 to USB Converter] on usb-0000:00:1a.0-1.2.1/input0 [ 1583.454764] input: CHESEN PS2 to USB Converter as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2.1/1-1.2.1:1.1/input/input18 [ 1583.455534] generic-usb 0003:0A81:0205.0002: input,hidraw1: USB HID v1.10 Mouse [CHESEN PS2 to USB Converter] on usb-0000:00:1a.0-1.2.1/input1 [ 1583.455578] usbcore: registered new interface driver usbhid [ 1583.455584] usbhid: USB HID core driver So I tried $ sudo udevadm test /sys/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2.1/1-1.2.1:1.0/0003:0A81:0205.0001/hidraw/hidraw0 run_command: calling: test adm_test: version 175 This program is for debugging only, it does not run any program, specified by a RUN key. It may show incorrect results, because some values may be different, or not available at a simulation run. parse_file: reading '/lib/udev/rules.d/40-crda.rules' as rules file parse_file: reading '/lib/udev/rules.d/40-fuse.rules' as rules file ... parse_file: reading '/lib/udev/rules.d/40-usb-media-players.rules' as rules file parse_file: reading '/lib/udev/rules.d/40-usb_modeswitch.rules' as rules file ... parse_file: reading '/lib/udev/rules.d/42-qemu-usb.rules' as rules file ... parse_file: reading '/lib/udev/rules.d/69-cd-sensors.rules' as rules file add_rule: IMPORT found builtin 'usb_id', replacing /lib/udev/rules.d/69-cd-sensors.rules:76 ... parse_file: reading '/lib/udev/rules.d/77-mm-usb-device-blacklist.rules' as rules file ... parse_file: reading '/lib/udev/rules.d/85-usbmuxd.rules' as rules file ... parse_file: reading '/lib/udev/rules.d/95-upower-hid.rules' as rules file parse_file: reading '/lib/udev/rules.d/95-upower-wup.rules' as rules file parse_file: reading '/lib/udev/rules.d/97-bluetooth-hid2hci.rules' as rules file udev_rules_new: rules use 271500 bytes tokens (22625 * 12 bytes), 44331 bytes buffer udev_rules_new: temporary index used 76320 bytes (3816 * 20 bytes) udev_device_new_from_syspath: device 0x7f78a5e4d2d0 has devpath '/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2.1/1-1.2.1:1.0/0003:0A81:0205.0001/hidraw/hidraw0' udev_device_new_from_syspath: device 0x7f78a5e5f820 has devpath '/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2.1/1-1.2.1:1.0/0003:0A81:0205.0001/hidraw/hidraw0' udev_device_read_db: device 0x7f78a5e5f820 filled with db file data udev_device_new_from_syspath: device 0x7f78a5e60270 has devpath '/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2.1/1-1.2.1:1.0/0003:0A81:0205.0001' udev_device_new_from_syspath: device 0x7f78a5e609c0 has devpath '/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2.1/1-1.2.1:1.0' udev_device_new_from_syspath: device 0x7f78a5e61160 has devpath '/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2.1' udev_device_new_from_syspath: device 0x7f78a5e61960 has devpath '/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2' udev_device_new_from_syspath: device 0x7f78a5e62150 has devpath '/devices/pci0000:00/0000:00:1a.0/usb1/1-1' udev_device_new_from_syspath: device 0x7f78a5e62940 has devpath '/devices/pci0000:00/0000:00:1a.0/usb1' udev_device_new_from_syspath: device 0x7f78a5e630f0 has devpath '/devices/pci0000:00/0000:00:1a.0' udev_device_new_from_syspath: device 0x7f78a5e638a0 has devpath '/devices/pci0000:00' udev_event_execute_rules: no node name set, will use kernel supplied name 'hidraw0' udev_node_add: creating device node '/dev/hidraw0', devnum=251:0, mode=0600, uid=0, gid=0 udev_node_mknod: preserve file '/dev/hidraw0', because it has correct dev_t udev_node_mknod: preserve permissions /dev/hidraw0, 020600, uid=0, gid=0 node_symlink: preserve already existing symlink '/dev/char/251:0' to '../hidraw0' udev_device_update_db: created empty file '/run/udev/data/c251:0' for '/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2.1/1-1.2.1:1.0/0003:0A81:0205.0001/hidraw/hidraw0' ACTION=add DEVNAME=/dev/hidraw0 DEVPATH=/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2.1/1-1.2.1:1.0/0003:0A81:0205.0001/hidraw/hidraw0 MAJOR=251 MINOR=0 SUBSYSTEM=hidraw UDEV_LOG=6 USEC_INITIALIZED=969079051 The later lines sound like it's already there. And none of these awakes the keyboard: $ sudo udevadm trigger --verbose --sysname-match=usb* /sys/devices/pci0000:00/0000:00:1a.0/usb1 /sys/devices/pci0000:00/0000:00:1a.0/usbmon/usbmon1 /sys/devices/pci0000:00/0000:00:1d.0/usb2 /sys/devices/pci0000:00/0000:00:1d.0/usbmon/usbmon2 /sys/devices/virtual/usbmon/usbmon0 $ sudo udevadm trigger --verbose --sysname-match=hidraw0 /sys/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2.1/1-1.2.1:1.0/0003:0A81:0205.0001/hidraw/hidraw0 $ sudo udevadm trigger I also tried this to no avail: # echo -n 0003:0A81:0205.0001 > /sys/bus/hid/drivers/generic-usb/bind ksh: echo: write to 1 failed [No such device] # echo -n 0003:0A81:0205.0001 > /sys/bus/hid/drivers/generic-usb/unbind # echo -n 0003:0A81:0205.0001 > /sys/bus/hid/drivers/generic-usb/bind # echo usb1 >/sys/bus/usb/drivers/usb/unbind # echo usb1 >/sys/bus/usb/drivers/usb/bind What else should I try to get the same result as replugging or suspending, by just issuing a command?

  Read the article

• mount old ATA disk to USB adapter

  - by 213441265152351

  I am trying to recover data from an old Linux that was installed in a computer on an ATA hard drive. I found a ScanLogic USB-IDE, an ATA adapter to USB 1.0 similar to the one in the picture: and after switching it on, I plugged it into a laptop with Ubuntu 12.04. I am used to the drives being automatically mounted, but this one doesn't show up in /media. After doing a dmesg, all I got is this: [215298.671924] usb 2-1.1: new full-speed USB device number 5 using ehci_hcd [215298.767330] scsi19 : usb-storage 2-1.1:1.0 [215299.841701] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd [215300.017258] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd [215300.197050] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd [215300.372730] usb 2-1.1: reset full-speed USB device number 5 using ehci_hcd I tried plugging in the adapter to the three different USB ports in my laptop (one of them USB 3.0), but got no luck with any of them. Any ideas?

  Read the article

• Wireless Keyboard Intermittent Failure to Type and Added Characters

  - by Kashif

  My keyboard has been acting up from time to time. It's wireless so this may be a wireless issue. What happens is I will be typing and then all of a sudden it seems to stop responding. If I type out this sentence it may show up like so If I ttennnnnnnnn it may ssssssp so While typing that sentence I may have to mash on a key repeatedly to get it to type. The resulting strings of letters seem to be coming as if the keyboard buffer cannot keep up. It's so weird. If I take the USB tranceiver and yank it out then plug it back in, Voila! Problem solved. I did the battery check so that's not a problem. Any suggestions? My keyboard is the Logitech MX3200

  Read the article

• USB drives not recognized all of a sudden (module usb_storage not loading)

  - by Siddharth

  I am very close to the solution, just need to know how to get usb-storage to load I have tried most of the advice on askubuntu and other sites, usb_storage enable to fdisk -l. But I am unable to find steps to get it working again. sudo lsusb results Bus.... skipped 4 lines Bus 004 Device 002: ID 413c:3012 Dell Computer Corp. Optical Wheel Mouse Bus 005 Device 002: ID 413c:2105 Dell Computer Corp. Model L100 Keyboard Bus 001 Device 005: ID 8564:1000 sudo dmseg | tail reports [ 69.567948] usb 1-4: USB disconnect, device number 4 [ 74.084041] usb 1-6: new high-speed USB device number 5 using ehci_hcd [ 74.240484] Initializing USB Mass Storage driver... [ 74.256033] scsi5 : usb-storage 1-6:1.0 [ 74.256145] usbcore: registered new interface driver usb-storage [ 74.256147] USB Mass Storage support registered. [ 74.257290] usbcore: deregistering interface driver usb-storage fdisk -l reports Device Boot Start End Blocks Id System /dev/sda1 * 2048 972656639 486327296 83 Linux /dev/sda2 972658686 976771071 2056193 5 Extended /dev/sda5 972658688 976771071 2056192 82 Linux swap / Solaris I think I need steps to install and get usb_storage module working. Edit : I tried sudo modprobe -v usb-storage reports sudo modprobe -v usb-storage insmod /lib/modules/3.2.0-48-generic-pae/kernel/drivers/usb/storage/usb-storage.ko Edit : jsiddharth@siddharth-desktop:~$ sudo udevadm monitor --udev monitor will print the received events for: UDEV - the event which udev sends out after rule processing UDEV [4757.144372] add /module/usb_storage (module) UDEV [4757.146558] remove /module/usb_storage (module) UDEV [4757.148707] add /devices/pci0000:00/0000:00:1d.7/usb1/1-6 (usb) UDEV [4757.149699] add /bus/usb/drivers/usb-storage (drivers) UDEV [4757.151214] remove /bus/usb/drivers/usb-storage (drivers) UDEV [4757.156873] add /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0 (usb) UDEV [4757.160903] add /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/host9 (scsi) UDEV [4757.164672] add /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/host9/scsi_host/host9 (scsi_host) UDEV [4757.165163] remove /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/host9/scsi_host/host9 (scsi_host) UDEV [4757.165440] remove /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/host9 (scsi) Narrowing down more : Seems like I need usb_storage to load as a module jsiddharth@siddharth-desktop:~$ lsmod | grep usb usbserial 37201 0 usbhid 41937 0 hid 77428 1 usbhid Still no usb driver mounted. Nor does a device show up in /dev. Any step by step process to debug and fix this will be really helpful.

  Read the article

• How can I automatically change the system keyboard layout when plugging in an external keyboard?

  - by Andrew Bolster

  I have a US-Style laptop, which is fine, but I also have a UK-style Ergonomic USB keyboard. As such I usually have the US key layout set, but when I settle in at my desk and use the UK USB keyboard I find myself making stupid mistakes on symbols (normally a pretty good touch typist on either ergo or standard kbd). Can anyone think of a clean way of setting the keyboard layout based on the inferred layout/USBID of any plugged in Keyboard? Even having a custom setting such as adding a specific USB ID to a runtime script that checks if its plugged in or not. Can this be done without the user having to logout/in? I remember doing something similar with xorg.conf, but that required logout.

  Read the article

• Can't add more than eight keyboard layouts

  - by Woofi Alakhi

  I read this article where is a workaround to add maximum eight keyboard layouts. But my questions are: I would like to try this, but I see they've written there something with "gnome" in the script. In my Ubuntu, 13.04, I have Unity. What do I do? I would have to do this for four x four keyboard layouts (to have 13 keyboard layouts). This script, however, is designed for two x four keyboard layouts. How do I get the four x four? I would really appreciate your tips and hints on this. And I would kindly ask you to keep it simple, if possible, because I'm really no expert in both Ubuntu and computers in general.

  Read the article

• usb keyboard works except in terminal window (SOLVED)

  - by matrixunloaded

  I just installed 12.10 (clean install and updates). USB keyboard and mouse work fine EXCEPT the keyboard does not work in a terminal window (USB mouse is working in terminal). keyboard is Logitech MK320 and associated mouse. I'm typing in a mozilla window on the keyboard at this very moment and when I switch to the terminal window, nothing can be typed. Any ideas? I use terminal mode alot. Thanks matrixunloaded I didn't realize passwords do not show even an asterisk in terminal mode! I'd just installed 12.10 and was pasting a long sudo command and then typing my password (which looked like nothing appearing)

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >