Search Results

Search found 17129 results on 686 pages for 'wifi configuration'.

Page 2/686 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

  • Slow wifi on Ubuntu 12.04 wifi driver ath9k

    - by lunar
    For the last couple of days my wifi connection is extremely slow. I am pretty sure that it is caused by the driver. Can this be improved? lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"MyWiFi" Mode:Managed Frequency:2.437 GHz Access Point: 00:18:68:FE:7B:C7 Bit Rate=58.5 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=48/70 Signal level=-62 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:6960 Missed beacon:0 eth0 no wireless extensions. sudo lshw -class network *-network description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 01 serial: 74:f0:6d:34:c2:4e width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-31-generic-pae firmware=N/A ip=192.168.1.2 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:d7400000-d740ffff *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:06:00.0 logical name: eth0 version: c0 serial: 48:4b:38:78:f6:ae capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI firmware=N/A latency=0 link=no multicast=yes port=twisted pair resources: irq:51 memory:d3800000-d383ffff ioport:8000(size=128) lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 003: ID 04f2:b1bb Chicony Electronics Co., Ltd Bus 001 Device 004: ID 0b05:1788 ASUSTek Computer, Inc. lspci 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 18) 00:01.0 PCI bridge: Intel Corporation Core Processor PCI Express x16 Root Port (rev 18) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 18) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06) 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 06) 00:1c.3 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 4 (rev 06) 00:1c.4 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 5 (rev 06) 00:1c.5 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 6 (rev 06) 00:1d.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a6) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 06) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA AHCI Controller (rev 06) 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 06) 01:00.0 VGA compatible controller: NVIDIA Corporation GF108 [GeForce GT 425M] (rev a1) 03:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) 04:00.0 USB controller: Fresco Logic Device 1400 (rev 01) 06:00.0 Ethernet controller: Atheros Communications Inc. AR8131 Gigabit Ethernet (rev c0) ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 05) ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 05) ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 05) ff:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 05) ff:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 05) ff:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 05) rfkill list all 0: hci0: Bluetooth Soft blocked: yes Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no

    Read the article

  • Slow wifi from Windows Server 2003 virtualized in XenServer

    - by John Clayton
    I'm a brand spanking new user of OS X, coming from a lifetime of Windows use. I've been setting up my new Macbook Pro and have run into a very unusual problem. Over wifi, I am unable to copy files to or from my Windows Home Server. The problem seems to exist only over wifi, and only to WHS. Here are the details of my setup: 2010 Macbook Pro (Core i7), OS X 10.6.3 Windows Home Server PP3 (virtualized in XenServer 5.5) Windows 7 Ultimate x64 desktop Windows 7 Ultimate x64 in Boot Camp D-Link DIR-655 wireless N router Here is what I've done to narrow down the problem: Files copy fine from WHS to OS X when using gigabit ethernet Files copy fine from desktop to OS X when using gigabit ethernet Files fail to copy from WHS to OS X when using wifi (error -51) Files copy fine from desktop to OS X when using wifi Files copy fine from WHS to Boot Camp when using wifi Files copy fine from desktop to Boot Camp when using wifi From what I can tell, it seems to be some sort of issue between OS X and WHS, but I can't for the life of me see what would be different between shares on WHS and my desktop. They are both connected using smb://ADDRESS (I've tried both by IP and name). I can browse the shares on the WHS, but copying to OS X fails. I originally found the issue while installing VS2010 off an ISO from WHS, mounted to a Windows 7 VM using VMware Fusion. During the installation the VM was unusable - even the clock got behind the host be about 8 minutes. Once I plugged in the ethernet and disabled the wifi things picked up and finished quickly. The Fusion 3.1 RC is the only I think of that I installed that may have messed with the wifi driver. I've also tried resetting the wifi router, and have changed it from being G & N to N-only. Under Boot Camp I get similar speeds as my wife's N laptop. Any ideas? Thanks! Update: The issue has been further narrowed down to Windows Server 2003, which Windows Home Server is based on, running in XenServer with the XenServer tools installed.

    Read the article

  • Dell R610 memory configuration for all 12 slots

    - by Neal
    I purchased 12 sticks of RAM on eBay to go into a Dell R610 server. The RAM is ECC REG PC3-12800 DDR3-1600 yet when I occupy all 12 slots with this ram I get the following error on boot: MEMORY Initialization Warning: Memory Size May be Reduced MEMBIST failure – The following DIMM has been disabled by Bios: DIMM B2 MEMBIST failure – The following DIMM has been disabled by Bios: DIMM B5 I am using all of the latest versions, BIOS, etc. I am using 2 x x5660 processors. What is causing this issue and is it correctable? If this RAM is incorrect what is correct to maximize the RAM on this server? Thank you.

    Read the article

  • Directly editing IIS 7 applicationHost.config configuration file

    - by lunadesign
    I know that IIS 7+ now uses XML config files instead of the metabase. I also know that if I edit a web.config file for a given site, IIS automagically detects the changes and implements any corresponding config changes. However, does this also apply to the server-level applicationHost.config settings file? (Its usually located in C:\windows\system32\inetsrv\config.) Specifically, is it safe to carefully edit this file instead of using IIS Manager or the appcmd command line utility? I couldn't find anything in the documentation that said it was okay or not okay to do this. I'm curious because I have to change the bindings for numerous sites from one IP to another. It would be much faster to simply do a global search and replace for the IP address in the config file instead of manually editing a few dozen sites in the GUI.

    Read the article

  • Designing configuration for subobjects

    - by Stefano Borini
    I have the following situation: I have a class (let's call it Main) encapsulating a complex process. This class in turn orchestrates a sequence of subalgorithms (AlgoA, AlgoB), each one represented by an individual class. To configure Main, I have a configuration stored into a configuration object MainConfig. This object contains all the config information for AlgoA and AlgoB with their specific parameters. AlgoA has no interest to the information relative to the configuration of AlgoB, so technically I could have (and in practice I have) a contained MainConfig.AlgoAConfig and MainConfig.AlgoBConfig instances, and initialize as AlgoA(MainConfig.AlgoAConfig) and AlgoB(MainConfig.AlgoBConfig). The problem is that there is some common configuration data. One example is the printLevel. I currently have MainConfig.printLevel. I need to propagate this information to both AlgoA and AlgoB, because they have to know how much to print. MainConfig also needs to know how much to print. So the solutions available are I pass the MainConfig to AlgoA and AlgoB. This way, AlgoA has technically access to the whole configuration (even that of AlgoB) and is less self-contained I copy the MainConfig.printLevel into AlgoAConfig and AlgoBConfig, so I basically have three printLevel information repeated. I create a third configuration class PrintingConfig. I have an instance variable MainConfig.printingConfig, and then pass to AlgoA both MainConfig.AlgoAConfig and MainConfig.printingConfig. Have you ever found this situation? How did you solve it ? Which one is stylistically clearer to a new reader of the code ?

    Read the article

  • Configuration of the network manager via DBus: how to set the ad hoc mode

    - by Andrea
    I have an hard nut to crack: a nice bottle of italian Chianti wine to the solver! :) To automatically configure Wifi, I first have to kill the network manager and than activate the wifi via the commandline: I do this all automatically in my application and works great. However... it is not the right way to do this. As the user has no network gui anymore to configure some other network access. A much better and transparent way would be to configure wifi directly via network manager over the DBus interface. I was able to configure it, but I wasn't able to set it to ad hoc mode... Searching the web for a while: a lot about configuration in general but nothing related to ad hoc mode. I think the only way to do figure that out is to look into the source code of the network manager...maybe someone already did it and he can answer.

    Read the article

  • SSIS Configuration error: Cannot retrieve configuration table schema

    - by Glenn M
    I'm trying to add a simple configuration to a SSIS package, of type SQL Server, so stored in a table. At the end of the wizard, when it goes to try and write a new row to the nominated table to store the configuration it fails with the error: TITLE: Microsoft Visual Studio Could not complete wizard actions. Cannot retrieve configuration table schema. (Microsoft.DataTransformationServices.Wizards) I can't seem to resolve this. The configuration connection has full permissions on the table, and it sees it and can read from it as it reports there is no current data for the filter I provide. It just wont write to it. A Google search of the error message above in quotes returns literally no hits! Any suggestions? Glenn

    Read the article

  • SharePoint: Can't Connect to a Configuration Database When Using Configuration Wizard

    - by Denis
    Hello everyone. I wonder if you could help me with the following problem: We have a SharePoint farm consisted of two servers with an NLB (a load balancer), a database server and an index server (4 servers in total). The issues initially appeared when we were trying to change Search settings via Shared services provider and an error was appearing with the message I can’t even remember now. To fix that problem, we decided to restart Search services on the Index server via Central Administration… and the process had stuck with a status “stopping” for several days. We’ve found a few solutions on the forums, but nothing had helped. Then we’ve tried to exclude the Index server from the farm, but yet again, Search services would not stop. However, after a week we’ve noticed that the services finally stopped. That was a prologue. So, after the Search services have finally stopped, we decided to return the Index server back to the farm via the SharePoint Configuration wizard. When we click on a button “Search database instances” (don’t know the exact name in English, we have a Russian version), a correct database name and user are automatically appear in the relevant fields. Then we supply a password for the user and click “next” two times and the configuration begins. Unfortunately, at the second stage we receive the error “Could not connect to a configuration database” with the exception in the log file: “Exception: System.Reflection.TargetInvocationException: Exception has been thrown by the target of an invocation.” Now we can’t figure out why the configuration wizard can’t connect to the configuration database. Any suggestions will be really appreciated.

    Read the article

  • Use case for sharing wifi over bluetooth?

    - by Andrew Koester
    What is the use case for applications like PDAnet or Android Wifi Tether supporting sharing wifi over Bluetooth? A friend and I were discussing this, and neither of us could figure out why you would need to redistribute wifi over a Bluetooth connection. In most cases, said receiving device would already have wifi. Any clues would be appreciated.

    Read the article

  • How to see who is using my wifi

    - by Bakhtiyor
    Dear all. Such a question. I have WiFi router at home and would like to know if there is any way to know who is connected to my WiFi network and using it. My WiFi network is password protected but still there could be chances that neighbors crack it and could use my WiFi for free. For this reason I would like to know is there is any tool to inspect the log of WiFi router in order to know which computers are connecting to it. Thanks a lot beforehand.

    Read the article

  • I installed the Nautilus Actions Configuration utility but I don't have the action configuration menu option

    - by userman
    I am tyring to set up my trash to securely delete items and I am following the instructions on this page. http://techthrob.com/2010/07/07/adding-a-secure-delete-option-to-nautilus-file-manager-in-linux/ I installed the Nautilus Actions Configuration utility and according to the previously listed page a new action configuration menu option should have shown up in the Nautilus preferences menu. It didn't. Any help would be appreciated. Thanks!

    Read the article

  • Could not apply the stored configuration for the monitor

    - by dellphi
    I'm using Nvidia 7300 gt and monitor-Acer V173w, on 64 bit Ubuntu 10.04. Compiz and Emerald went well, but at the time of entry into the GUI, I always receive the message : "Could not apply the stored configuration for the monitor, could not find a suitable configuration of screens" Why do I always receive it, and what is wrong with the monitor configuration or pci-e is used? root@dellph1-desktop:/# xrandr Screen 0: minimum 320 x 240, current 1440 x 900, maximum 1440 x 900 default connected 1440x900+0+0 0mm x 0mm 1440x900 50.0* 1024x768 51.0 58.0 59.0 1360x768 52.0 53.0 1152x864 54.0 55.0 56.0 57.0 960x600 60.0 960x540 61.0 896x672 62.0 840x525 63.0 64.0 65.0 66.0 832x624 67.0 800x600 68.0 69.0 70.0 71.0 72.0 73.0 800x512 74.0 720x450 75.0 680x384 76.0 77.0 640x512 78.0 79.0 640x480 80.0 81.0 82.0 83.0 576x432 84.0 85.0 86.0 87.0 512x384 88.0 89.0 90.0 416x312 91.0 400x300 92.0 93.0 94.0 95.0 320x240 96.0 97.0 98.0 root@dellph1-desktop:/# === xorg.conf # nvidia-settings: X configuration file generated by nvidia-settings # nvidia-settings: version 260.19.29 ([email protected]) Wed Dec 8 12:27:27 PST 2010 Section "ServerLayout" Identifier "Layout0" Screen 0 "Screen0" 0 0 InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" Option "Xinerama" "0" EndSection Section "Files" EndSection Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psaux" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" # generated from default Identifier "Keyboard0" Driver "kbd" EndSection Section "Monitor" # HorizSync source: xconfig, VertRefresh source: xconfig Identifier "Monitor0" VendorName "Unknown" ModelName "Acer V173W" HorizSync 30.0 - 83.0 VertRefresh 55.0 - 75.0 Option "DPMS" EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce 7300 GT" EndSection Section "Screen" # Removed Option "metamodes" " 1440x900_60 +0+0; 1280x1024 +0+0" # Removed Option "metamodes" "1440x900 +0+0" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 Option "TwinView" "0" Option "TwinViewXineramaInfoOrder" "CRT-0" Option "metamodes" "1440x900_75 +0+0; 1440x900 +0+0" SubSection "Display" Depth 24 EndSubSection EndSection

    Read the article

  • Calling Save on a Configuration obj with a custom sectiongroup of type NameValueSectionHandler

    - by Allen
    I've got aConfiguration object that I can easily read and write settings from and call Save(ConfigurationSaveMode.Minimal, true) on and that typically works just fine. However, I now have a config file that has a custom sectionGroup defined of type System.Configuration.NameValueSectionHandler (I didn't write that part and I can't change it). Now when I call the Save method, it throws a TypeLoadException Message: Type System.Configuration.NameValueSectionHandler does not inherit from System.Configuration.ConfigurationSectionGroup. Callstack: at System.Configuration.TypeUtil.VerifyAssignableType (Type baseType, Type type, Boolean throwOnError) at System.Configuration.TypeUtil.GetConstructorWithReflectionPermission (Type type, Type baseType, Boolean throwOnError) at System.Configuration.MgmtConfigurationRecord.CreateSectionGroupFactory (FactoryRecord factoryRecord) at System.Configuration.MgmtConfigurationRecord.EnsureSectionGroupFactory (FactoryRecord factoryRecord) at System.Configuration.MgmtConfigurationRecord.GetSectionGroup (String configKey) at System.Configuration.ConfigurationSectionGroupCollection.Get (String name) at System.Configuration.ConfigurationSectionGroupCollection. <GetEnumerator>d__0.MoveNext() at System.Configuration.Configuration.ForceGroupsRecursive (ConfigurationSectionGroup group) at System.Configuration.Configuration.SaveAsImpl (String filename, ConfigurationSaveMode saveMode, Boolean forceSaveAll) at System.Configuration.Configuration.Save (ConfigurationSaveMode saveMode, Boolean forceSaveAll) at MyCompany.MyProduct.blah.blah.Save () in C:\\projects\\blah\\blah\\blah.cs:line blah For reference, the configuration goes like so <configuration> <configSections> ... normal sections here that work just fine, followed by ... <sectionGroup name="threadSettings" type="System.Configuration.NameValueSectionHandler"> <section name="T1" type="System.Configuration.DictionarySectionHandler"/> <section name="T2" type="System.Configuration.DictionarySectionHandler"/> <section name="T3" type="System.Configuration.DictionarySectionHandler"/> </sectionGroup> </configSections> <applicationSettings /> <threadSettings> <T1> <add key="key-here" value="value-here"/> </T1> ... T2 and T3 here as well, thats not interesting ... </threadSettings> </configuration> If I remove the actual sections and the definition for the custom section groups, I am able to read / write settings just fine and even call Save just fine. Obviously the custom section groups could be setup a little nicer but I can't fix that so I'm wondering: Is it possible to get the Configuration object to save if it has custom sectionGroups of the NameValueSectionHandler type

    Read the article

  • Can't connect to public WiFi with MacBookPro at coffee shops and libraries

    - by Nathan Bowers
    The Problem: I can't connect to public, unencrypted WiFi at my local public library or Peets Coffee. My Setup: Late 2006 MacBookPro running 10.5.8. I have Parallels installed. It's supposed to work like this: 1) Connect to their unencrypted WiFi network 2) Open a browser which redirects you to their "enter password/agree to terms" page. 3) Browse normally. I can connect to the WiFi network, but when I try to authenticate I always get stuck in a redirect loop. It's been like this for a while. Even before I upgraded to 10.5.8. I never have trouble with encrypted networks or regular open WiFi. What I've tried: Disabling Parallels connections in Network Prefs. Superstition: somehow Parallels installed something in the network stack that's messing me up. Pinging the IP address of the WiFi node I'm connected to. I can ping it, it's there, but I still get stuck in this authentication redirect loop. Tried different browsers, tried different cookie and security settings. Even tried IE under Parallels. No dice. Tried flushing DNS cache. Asked library and coffee employees for help. It didn't go well. My Question: Anybody else have this problem? What should I be looking for?

    Read the article

  • WiFi N Gigabit Router

    - by SLaks
    I'm looking for a WiFi N Gigabit router. I'll be using an iPod Touch 2G and a 2009 17" MacBook Pro over WiFi, and I need at least 4 gigabit ethernet ports plus a WAN port. What do people recommend? In particular, are there any compatibility issues between different WiFi N drafts that would limit the speed of the MacBook, and is it worth getting dual-band?

    Read the article

  • Oracle Enterprise Manager 12c Configuration Best Practices (Part 3 of 3)

    - by Bethany Lapaglia
    <span id="XinhaEditingPostion"></span>&amp;lt;span id=&amp;quot;XinhaEditingPostion&amp;quot;&amp;gt;&amp;lt;/span&amp;gt;&amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;lt;span id=&amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;quot;XinhaEditingPostion&amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;quot;&amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;gt;&amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;lt;/span&amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;amp;gt; This is part 3 of a three-part blog series that summarizes the most commonly implemented configuration changes to improve performance and operation of a large Enterprise Manager 12c environment. A “large” environment is categorized by the number of agents, targets and users. See the Oracle Enterprise Manager Cloud Control Advanced Installation and Configuration Guide chapter on Sizing for more details on sizing your environment properly. Part 1 of this series covered recommended configuration changes for the OMS and Repository Part 2 covered recommended changes for the Weblogic server Part 3 covers general configuration recommendations and a few known issues The entire series can be found in the My Oracle Support note titled Oracle Enterprise Manager 12c Configuration Best Practices [1553342.1]. Configuration Recommendations Configure E-Mail Notifications for EM related Alerts In some environments, the notifications for events for different target types may be sent to different support teams (i.e. notifications on host targets may be sent to a platform support team). However, the EM application administrators should be well informed of any alerts or problems seen on the EM infrastructure components. Recommendation: Create a new Incident rule for monitoring all EM components and setup the notifications to be sent to the EM administrator(s). The notification methods available can create or update an incident, send an email or forward to an event connector. To setup the incident rule set follow the steps below. Note that each individual rule in the rule set can have different actions configured. 1.  To create an incident rule for monitoring the EM components, click on Setup / Incidents / Incident Rules. On the All Enterprise Rules page, click on the out-of-box rule called “Incident management Ruleset for all targets” and then click on the Actions drop down list and select “Create Like Rule Set…” 2. For the rule set name, enter a name such as MTM Ruleset. Under the Targets tab, select “All targets of types” and select “OMS and Repository” from the drop down list. This target type contains all of the key EM components (OMS servers, repository, domains, etc.) 3. Click on the Rules tab. To edit a rule, click on the rule name and click on Edit as seen below 4. Modify the following rules: a. Incident creation Rule for metric alerts i. Leave the Type set as is but change the Severity to add Warning by clicking on the drop down list and selecting “Warning”. Click Next. ii.  Add or modify the actions as required (i.e. add email notifications). Click Continue and then click Next. iii. Leave the Name and description the same and click Next. iv. Click Continue on the Review page. b. Incident creation Rule for target unreachable. i.   Leave the Type set as is but change the Target type to add OMS and Repository by clicking on the drop down list selecting “OMS and Repository”. Click Next. ii.  Add or modify the actions as required (i.e. add email notifications) Click Continue and then click Next. iii. Leave the Name and description the same and click Next. iv. Click Continue on the Review page. 5.  Modify the actions for any other rule as required and be sure to click the “Save” push button to save the rule set or all changes will be lost. Configure Out-of-Band Notifications for EM Agent Out-of-Band notifications act as a backup when there’s a complete EM outage or a repository database issue. This is configured on the agent of the OMS server and can be used to send emails or execute another script that would create a trouble ticket. It will send notifications about the following issues: • Repository Database down • All OMS are down • Repository side collection job that is broken or has an invalid schedule • Notification job that is broken or has an invalid schedule Recommendation: To setup Out-of-Band Notifications, refer to the MOS note “How To Setup Out Of Bound Email Notification In 12c” (Doc ID 1472854.1) Modify the Performance Test for the EM Console Service The EM Console Service has an out-of-box defined performance test that will be run to determine the status of this service. The test issues a request via an HTTP method to a specific URL. By default, the HTTP method used for this test is a GET but for performance reasons, should be changed to HEAD. The URL used for this request is set to point to a specific OMS server by default. If a multi-OMS system has been implemented and the OMS servers are behind a load balancer, then the URL in this section must be modified to point to the load balancer name instead of a specific server name. If this is not done and a portion of the infrastructure is down then the EM Console Service will show down as this test will fail. Recommendation: Modify the HTTP Method for the EM Console Service test and the URL if required following the detailed steps below. 1.  To create an incident rule for monitoring the EM components, click on Targets / Services. From the list of services, click on the EM Console Service. 2. On the EM Console Service page, click on the Test Performance tab. 3.  At the bottom of the page, click on the Web Transaction test called EM Console Service Test 4.  Click on the Service Tests and Beacons breadcrumb near the top of the page. 5.  Under the Service Tests section, make sure the EM Console Service Test is selected and click on the Edit push button. 6.  Under the Transaction section, make sure the Access Logout page transaction is selected and click on the Edit push button 7) Under the Request section, change the HTTP Method from the default of GET to the recommended value of HEAD. The URL in this section must be modified to point to the load balancer name instead of a specific server name if multi-OMSes have been implemented. Check for Known Issues Job Purge Repository Job is Shown as Down This issue is caused after upgrading EM from 12c to 12cR2. On the Repository page under Setup ? Manage Cloud Control ? Repository, the job called “Job Purge” is shown as down and the Next Scheduled Run is blank. Also, repvfy reports that this is a missing DBMS_SCHEDULER job. Recommendation: In EM 12cR2, the apply_purge_policies have been moved from the MGMT_JOB_ENGINE package to the EM_JOB_PURGE package. To remove this error, execute the commands below: $ repvfy verify core -test 2 -fix To confirm that the issue resolved, execute $ repvfy verify core -test 2 It can also be verified by refreshing the Job Service page in EM and check the status of the job, it should now be Up. Configure the Listener Targets in EM with the Listener Password (where required) EM will report this error every time it is encountered in the listener log file. In a RAC environment, typically the grid home and rdbms homes are owned by different OS users. The listener always runs from the grid home. Only the listener process owner can query or change the listener properties. The listener uses a password to allow other OS users (ex. the agent user) to query the listener process for parameters. EM has a default listener target metric that will query these properties. If the agent is not permitted to do this, the TNS incident (TNS-1190) will be logged in the listener’s log file. This means that the listener targets in EM also need to have this password set. Not doing so will cause many TNS incidents (TNS-1190). Below is a sample of this error from the listener log file: Recommendation: Set a listener password and include it in the configuration of the listener targets in EM For steps on setting the listener passwords, see MOS notes: 260986.1 , 427422.1

    Read the article

  • Using ADSL Modem/WiFi Router to share existing network wirelessly

    - by joshhunt
    At my uni we have a wired Ethernet connection in our dorms. However, I want to share this connection with my macbook using wifi (so I don't have to be constantly tethered). I am looking at using my DSL G064T ADSL modem/WiFi router as a wifi repeater for the uni network. Is this possible? How would I go about doing this? I understand that it would be possible using a normal Wifi router (seeing as it has an ethernet 'in' port where it would get the external connection from.), so is it just not possible using the router I have? If i need to buy another one, which one would you recommend?

    Read the article

  • Leaving my wifi open for the world

    - by Thomaschaaf
    For my home I want to be a nice neighbor actually I have let my wifi open for the past maybe 6 or 7 years. I know that WEP, etc can be cracked within a couple of minutes but my neighbors son who works in IT told his mom and she told me that I am doing bad things and you know the story.. Do you think it's okay to leave your wifi open to the public? I live in a suburb with a tiny street and about 8 houses in reach of my wifi. I have a 16k DSL line so if some one joins me for a couple hours I would probably not notice. I would love your thoughts on whether I should encrypt my wifi or not.

    Read the article

  • Windows 7 wifi reports "no network access" and "no internet access" but connects in fedora

    - by rick2047
    I am running windows 7 home basic (64bit) on a Acer 5742G laptop with Atheos wifi adapter in it. Yesterday, I hiberneted my computer as I always do and up untill then the wifi was working fine. When I booted my computer up again today I started having a strange problem: It detects my wifi but after connecting to it, it keeps on oscillating between states of no network access and no internet access. I can't connect to anything (the internet or my router). I tried to reset my internet protocol stack using this fixit file. I also tried to uninstall and reinstall my network driver. Neither helped. I am using the same laptop's fedora installation right now and the wifi is working perfectly fine. Please help. Edit To add additional details, I have Microsoft Security essentials as my antivirus software and I haven't messed with the firewall or the router configurations.

    Read the article

  • Win XP cannot connect (or see) my wifi network, but can see others

    - by Jorre
    since yesterday I have a strange wifi problem with my pc. I have a wireless linksys router setup that worked fine for many months, now since yesterday my pc won't connect to the wifi signal anymore. The strange thing is, my macbook pro still connects fine. SSID is broadcasting, but my windows XP doens't see it, I have all signal modes set to "auto". Windows XP sees all my neighbours wifi networks, so the wifi card isn't broken or anything. Any idea what can be wrong here?

    Read the article

  • New security configuration flag in UCM PS3

    - by kyle.hatlestad
    While the recent Patch Set 3 (PS3) release was mostly focused on bug fixes and such, a new configuration flag was added for security. In 10gR3 and prior versions, UCM had a component called Collaboration Manager which allowed for project folders to be created and groups of users assigned as members to collaborate on documents. With this component came access control lists (ACL) for content and folders. Users could assign specific security rights on each and every document and folder within a project. And it was possible to enable these ACL's without having the Collaboration Manager component enabled. But it took some special instructions (see technote# 603148.1) and added some extraneous pieces still related to Collaboration Manager. When 11g came out, Collaboration Manager was no longer available. But the configuration settings to turn on ACLs were still there. Well, in PS3 they've been cleaned up a bit and a new configuration flag has been added to simply turn on the ACL fields and none of the other collaboration bits. To enable ACLs: UseEntitySecurity=true Along with this configuration flag to turn ACLs on, you also need to define which Security Groups will honor the ACL fields. If an ACL is applied to a content item with a Security Group outside this list, it will be ignored. SpecialAuthGroups=HumanResources,Legal,Marketing Save the settings and restart the instance. Upon restart, two new metadata fields will be created: xClbraUserList, xClbraAliasList. If you are using OracleTextSearch as the search indexer, be sure to run a Fast Rebuild on the collection. On the Check In, Search, and Update pages, values are added by simply typing in the value and getting a type-ahead list of possible values. Select the value, click Add and then set the level of access (Read, Write, Delete, or Admin). If all of the fields are blank, then it simply falls back to just Security Group and Account access. As for how they are stored in the metadata fields, each entry starts with it's identifier: ampersand (&) symbol for users, "at" (@) symbol for groups, and colon (:) for roles. Following that is the entity name. And at the end is the level of access in paranthesis. e.g. (RWDA). And each entry is separated by a comma. So if you were populating values through batch loader or an external source, the values would be defined this way. Detailed information on Access Control Lists can be found in the Oracle Fusion Middleware System Administrator's Guide for Oracle Content Server.

    Read the article

  • Extending configuration for .Net 3.5 Applications

    - by Maximiliano Rios
    Due to a requirement in my current project, I have to build a configuration manager to handle configurations that merge local config info with database one. Custom configuration doesn't fit my needs, problem is that I don't know what's the type before loading certain information, for example: Loading database information I will able to know what's myhandler's type. Not previously. So I thought to write my own handler but I can't let set blank as type for sections, in fact .net requires to know what's the type to match myhandler nodes. I'm thinking on building a different parser to read XML nodes but I would prefer to match this structure. I've not found any information to do that yet, is there any way? Can I extend or hook up something into the framework to be capable of loading on-the-fly types and validate nodes? Thanks in advance.

    Read the article

  • New Reference Configuration: Accelerate Deployment of Virtual Infrastructure

    - by monica.kumar
    Today, Oracle announced the availability of Oracle VM blade cluster reference configuration based on Sun servers, storage and Oracle VM software. Assembling and integrating software and hardware systems from different vendors can be a huge barrier to deploying virtualized infrastructures as it is often a complicated, time-consuming, risky and expensive process. Using this tested configuration can help reduce the time to configure and deploy a virtual infrastructure by up to 98% as compared to putting together multi-vendor configurations. Once ready, the infrastructure can be used to easily deploy enterprise applications in a matter of minutes to hours as opposed to days/weeks, by using Oracle VM Templates. Find out more: Press Release Business whitepaper Technical whitepaper

    Read the article

  • Skype does not save user configuration

    - by varsketiz
    On Ubuntu 10.10, I have recently started to experience this problem: For some reason Skype won't save any settings except "Sign in on startup". When Skype starts and tries to sign in it is unsuccessful (it shows incorrect password, in red) every time (I have provided the correct password). I always have to click to show contacts in groups, it does not remember it. Every time I have to go to options and update some notification settings. I know all these things should be "remembered" by Skype - this problem started only recently. I don't recall fiddling with any permissions that could have likely caused that. Do you know what the problem might be? I uninstalled (marking for complete configuration removal) and re-installed Skype, but it still remembers my username (why??). Can I find Skype configuration files on the filesystem somewhere and change permissions for them - or even better - edit the files to set what I want?

    Read the article

  • Skype does not save configuration

    - by varsketiz
    Hello, on ubuntu 10.10, I have recently started to experience this problem: for some reason skype wont save any settings except "sign in on startup" when skype starts and tries to sign in it is unsuccessful (it shows incorrect password, in red) every time. no matter if I have provided good password the last time. I always have to click to show contacts in groups, it does not remember it. Every time I have to go to options and update some notification settings. I know all these things should be "remembered" by skype - this problem started only recently. I don't recall fiddling with any permissions that could have likely caused that. Do you know what the problem might be? I tried uninstall (marking complete configuration removal) and install fresh, but it still remembers my username (why??) Can I find skype configuration files on the filesystem somewhere and change permissions for them - or even better - edit the files to set what I want..?

    Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >