Search Results

Search found 1913 results on 77 pages for 'james marthenal'.

Page 20/77 | < Previous Page | 16 17 18 19 20 21 22 23 24 25 26 27  | Next Page >

• Power cycles on/off 3 times before booting properly from cold start, no other issues (New System)

  - by James

  Relevant Specs: Sapphire 5850, core i7 920, Seasonic x750 power supply, ECS X58B-A2 mobo. From a cold boot, meaning all power totally disconnected at the wall, the system will power on for less than a second and then power off completely. After two seconds of being powered off this will repeat and on the third "attempt" the computer will boot. To be very specific here is what happens: The power is turned on at the wall and on the psu, the orange stdby LED on the mobo is illuminated but the system is 'off'. I hit the power button on the case or on the mobo itself I hear the relay (?) in the psu closing The case light comes on and the mobo power light comes on. The fans start rotating. Immediately after this the I hear some relay click - the power lights extinguish, the fans stop, the stdby light remains on. Less than 2 seconds pass and the cycle repeats without any intervention from me. On the third attempt it boots normally and the machine runs perfectly. If I do a soft reboot or a full shutdown the computer starts normally the next time. It's only if I pull the power cord or flick the switch off on the PSU that I get the cycling again. Basically any time the stdby light on the mobo goes out. I have removed the graphics card and I get the same problem. I have removed the PSU, hotwired it to the ON position and verified voltages on all lines. The relay does not cycle when I do this. If I connect only the 24 pin ATX connector to the mobo and not the 8 pin ATX12V / CPU connector then I will not get the cycling, the fans run, the power light stays on, but obviously the system can't boot. Disconnecting all fans has no effect on the problem. My feeling it that it's something to do with the motherboard like a capacitor that's taking a long time to charge because it's leaking or something along those lines. But I can't imagine what could be 'wrong' with it and only manifest itself as a problem under these very specific circumstances. Any ideas? Thanks.

  Read the article

• Ubuntu 8.04 server is not retaining a static IP address

  - by James Pierce

  I recently setup a linux box running Ubuntu 8.04 (to match another server with 8.04). I need to insure that this box has a static IP address and I changed /etc/network/interfaces to set up the static IP address and when I run sudo /etc/init.d/networking restart it works fine for a while, but always reverts back to 10.0.1.24 after being idle for a while. I also tried stopping/removing the dhcp client, but that didn't help. sudo /etc/init.d/dhcp stop sudo apt-get remove dhcp3-client Here is my /etc/init.d/networking: # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 10.0.1.4 netmask 255.255.255.0 broadcast 10.0.1.255 gateway 10.0.1.1 Any thoughts? Thanks.

  Read the article

• ActiveSync gives a 401.2 error

  - by Justin James

  Hello - I've been struggling for a while with a problem with ActiveSync, it is giving 401.2 errors when trying to access the mailboxes. Oddly enough, clients can get to the calendars just fine. I've tried from an Android device as well as the Exchange remote connectivity troubleshooter, same error both times. Here is the configuration: Connectivity through ISA 2006 Exchange 2007 on Windows 2008 Basic authentication is on ISA is passing through all authentication directly to the Exchange server The user IS allowed to get to ActiveSync in their Exchange mailbox settings I have tried the following, without success: * Making SSL not required * Enabling Windows Integrated and Digest authentication Here is an example of the errors in the IIS log: OPTIONS /Microsoft-Server-ActiveSync/default.eas - 443 - 192.168.32.18 TestActiveSyncConnectivity 401 2 5 0 Here is what I am seeing in my trace log: ModuleName IIS Web Core Notification 2 HttpStatus 401 HttpReason Unauthorized HttpSubStatus 2 ErrorCode 2147942405 ConfigExceptionInfo Notification AUTHENTICATE_REQUEST ErrorCode Access is denied. (0x80070005) I'm 100% stumped. Any clues? Thanks! J.Ja

  Read the article

• Helicon ISAPI Rewrite is processing Rewrite Rules for httpd.conf but not .htaccess

  - by James Lawruk

  We have Helicon ISAPI Rewrite 3 installed on our Windows 2003 Web server. The RewriteRules work fine in the global file located in the httpd.conf file. The server serves several Web sites and we were hoping to create RewriteRules to apply to specific Web sites. In the IIS Properties for each Web site there exists a separate tab for ISAPI_Rewrite pointing to the .htaccess file for that Web site. No rules applied to the .htaccess files work. Any ideas why the .htaaccess files have no effect.

  Read the article

• Windows7 and Virtual PC guest copy/paste intermittent delay

  - by James

  I've been using Virtual PC for some time now and have not had any issues with copy and paste until I upgraded my host to Windows7 64-bit. After the upgrade sometimes when I copy and paste some text there is like a 15-20 second delay before it completes, this is very frustrating when I'm trying to get my work done. The problem seems to be intermittent in nature, it seems to occur when I have not done a copy paste for a while. After the delay occurs copy and paste seem to work at normal speed until I don't copy and paste for a good length of time. My question is, is there any solutions or patches that can fix this copy/paste issue for virtual PC running in a 64-bit windows7 host?

  Read the article

• Windows 7 Backup not backing up custom library?

  - by James McMahon

  I have created a custom Library under Windows 7 64bit professional to handle my source code. When I tried Windows Backup and Restore for the first time I get the following error Backup encountered a problem while backing up file C:\Windows\System32\config\systemprofile\Source. Error:(The system cannot find the file specified. (0x80070002)) I've found a thread on the error on the Microsoft answers site. But it appears to be 404 (there is a version in Google's Cache) and the thread starter never gets an answer to his issue that works. The official Microsoft answer on this is This problem is due to one or more profiles under HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\WindowsNT\CurrentVersion\ProfileList with missing ProfileImagePath. To check whether you have missing profiles: Open regedit, navigate to the above registry key. (HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\ProfileList). Expand the list Click on each of the profiles listed. The first 3 profiles should have ProfileImagePath value of %SystemRoot%\System32\Config\SystemProfile, %SystemRoot%\ServiceProfiles\LocalService, and %SystemRoot%\ServiceProfiles\NetworkService respectively. Starting from the 4th profile, the ProfileImagePath should contain path to the user profiles on your machine, such as C:\users\Christine If one or more of the profile has no profile image, then you have missing profiles. To work around this, delete the profile in question (Caution: The registry contains critical settings that are necessary for your system to function properly. Take extra caution while making changes) First, export the ProfileList key for safekeeping. (Right click on the key, choose “Export”, and save it to the desktop.) Right click on the profile in question, choose delete. Try backup again. This does not work for me. Anyone have any idea what is going on here?

  Read the article

• iproute2 not functioning ("RTNETLINK answers: Operation not supported")

  - by James Watt

  The command and error message: gtwy ~ # ip rule add from 64.251.23.186 table t1 RTNETLINK answers: Operation not supported Older article of the same problem, but it did not help me: http://forums.gentoo.org/viewtopic-t-696982-start-0-postdays-0-postorder-asc-highlight-.html I have looked on google at great lengths to try to find a solution. It seems that my kernel configuration is missing something? Any help or ideas would be appreciated. My system/kernel is: 2.6.36-gentoo-r5 #3 SMP Thu Jan 13 10:49:06 EST 2011 x86_64 Intel(R) Xeon(R) CPU X3220 @ 2.40GHz GenuineIntel GNU/Linux. I am posting this on SuperUser since this system is used as a workstation and this problem is unrelated to specific tasks that are handled exclusively by servers. iproute2 is installed: gtwy etc # emerge --search iproute2 Searching... [ Results for search key : iproute2 ] [ Applications found : 1 ] * sys-apps/iproute2 Latest version available: 2.6.35-r2 Latest version installed: 2.6.35-r2 Size of files: 378 kB Homepage: http://www.linuxfoundation.org/collaborate/workgroups/networking/iproute2 Description: kernel routing and traffic control utilities License: GPL-2 A small snippet of my kernel .config (view entire .config): gtwy linux # cat .config | grep NETLINK CONFIG_NETFILTER_NETLINK=y CONFIG_NETFILTER_NETLINK_QUEUE=y CONFIG_NETFILTER_NETLINK_LOG=y CONFIG_NF_CT_NETLINK=y CONFIG_SCSI_NETLINK=y gtwy linux # cat .config | grep IP_ADVANCED_ROUTER CONFIG_IP_ADVANCED_ROUTER=y gtwy linux # cat .config | grep INGRESS CONFIG_NET_SCH_INGRESS=y gtwy linux # cat .config | grep NET_SCHED CONFIG_NET_SCHED=y emerge --info Portage 2.1.9.25 (default/linux/amd64/10.0, gcc-4.1.2, glibc-2.10.1-r1, 2.6.36-gentoo-r5 x86_64) ================================================================= System uname: Linux-2.6.36-gentoo-r5-x86_64-Intel-R-_Xeon-R-_CPU_X3220_@_2.40GHz-with-gentoo-1.12.13 Timestamp of tree: Thu, 13 Jan 2011 01:15:01 +0000 app-shells/bash: 4.0_p37 dev-java/java-config: 1.3.7-r1, 2.1.10 dev-lang/python: 2.4.6, 2.5.4-r4, 2.6.5-r2, 3.1.2-r3 sys-apps/baselayout: 1.12.13 sys-apps/sandbox: 1.6-r2 sys-devel/autoconf: 2.13, 2.65 sys-devel/automake: 1.9.6-r2::<unknown repository>, 1.10.2, 1.11.1 sys-devel/binutils: 2.20.1-r1 sys-devel/gcc: 4.1.2, 4.3.4, 4.4.3-r2 sys-devel/gcc-config: 1.4.1 sys-devel/libtool: 2.2.6b sys-devel/make: 3.81 virtual/os-headers: 2.6.30-r1 (sys-kernel/linux-headers) ACCEPT_KEYWORDS="amd64" ACCEPT_LICENSE="*" CBUILD="x86_64-pc-linux-gnu" CFLAGS="-march=nocona -O2 -pipe" CHOST="x86_64-pc-linux-gnu" CONFIG_PROTECT="/etc /var/bind" CONFIG_PROTECT_MASK="/etc/ca-certificates.conf /etc/env.d /etc/env.d/java/ /etc/fonts/fonts.conf /etc/gconf /etc/php/apache2-php5/ext-active/ /etc/php/cgi-php5/ext-active/ /etc/php/cli-php5/ext-active/ /etc/revdep-rebuild /etc/sandbox.d /etc/terminfo" CXXFLAGS="-march=nocona -O2 -pipe" DISTDIR="/usr/portage/distfiles" FEATURES="assume-digests binpkg-logs distlocks fixlafiles fixpackages news parallel-fetch protect-owned sandbox sfperms strict unknown-features-warn unmerge-logs unmerge-orphans userfetch" GENTOO_MIRRORS="http://gentoo.chem.wisc.edu/gentoo" LC_ALL="en_US.UTF-8" LDFLAGS="-Wl,-O1 -Wl,--as-needed" LINGUAS="en" MAKEOPTS="-j5" PKGDIR="/usr/portage/packages" PORTAGE_CONFIGROOT="/" PORTAGE_RSYNC_OPTS="--recursive --links --safe-links --perms --times --compress --force --whole-file --delete --stats --timeout=180 --exclude=/distfiles --exclude=/local --exclude=/packages" PORTAGE_TMPDIR="/var/tmp" PORTDIR="/usr/portage" PORTDIR_OVERLAY="/usr/local/portage" SYNC="rsync://rsync.namerica.gentoo.org/gentoo-portage" USE="acl amd64 apache2 berkdb bzip2 cli cracklib crypt ctype cups curl cxx dri fortran gdbm gpm iconv jpeg jpeg2k libwww mmx modules mudflap multilib mysql ncurses nls nptl nptlonly openmp pam pcre perl php png pppd python readline session sockets sse sse2 ssl symlink sysfs tcpd threads unicode vhosts xml xorg xsl zlib" ALSA_CARDS="ali5451 als4000 atiixp atiixp-modem bt87x ca0106 cmipci emu10k1x ens1370 ens1371 es1938 es1968 fm801 hda-intel intel8x0 intel8x0m maestro3 trident usb-audio via82xx via82xx-modem ymfpci" ALSA_PCM_PLUGINS="adpcm alaw asym copy dmix dshare dsnoop empty extplug file hooks iec958 ioplug ladspa lfloat linear meter mmap_emul mulaw multi null plug rate route share shm softvol" APACHE2_MODULES="actions alias auth_basic authn_alias authn_anon authn_dbm authn_default authn_file authz_dbm authz_default authz_groupfile authz_host authz_owner authz_user autoindex cache cgi cgid dav dav_fs dav_lock deflate dir disk_cache env expires ext_filter file_cache filter headers include info log_config logio mem_cache mime mime_magic negotiation rewrite setenvif speling status unique_id userdir usertrack vhost_alias" COLLECTD_PLUGINS="df interface irq load memory rrdtool swap syslog" ELIBC="glibc" GPSD_PROTOCOLS="ashtech aivdm earthmate evermore fv18 garmin garmintxt gpsclock itrax mtk3301 nmea ntrip navcom oceanserver oldstyle oncore rtcm104v2 rtcm104v3 sirf superstar2 timing tsip tripmate tnt ubx" INPUT_DEVICES="keyboard mouse evdev" KERNEL="linux" LCD_DEVICES="bayrad cfontz cfontz633 glk hd44780 lb216 lcdm001 mtxorb ncurses text" LINGUAS="en" PHP_TARGETS="php5-3" RUBY_TARGETS="ruby18" USERLAND="GNU" VIDEO_CARDS="fbdev glint intel mach64 mga neomagic nouveau nv r128 radeon savage sis tdfx trident vesa via vmware dummy v4l" XTABLES_ADDONS="quota2 psd pknock lscan length2 ipv4options ipset ipp2p iface geoip fuzzy condition tee tarpit sysrq steal rawnat logmark ipmark dhcpmac delude chaos account" Unset: CPPFLAGS, CTARGET, EMERGE_DEFAULT_OPTS, FFLAGS, INSTALL_MASK, LANG, PORTAGE_BUNZIP2_COMMAND, PORTAGE_COMPRESS, PORTAGE_COMPRESS_FLAGS, PORTAGE_RSYNC_EXTRA_OPTS

  Read the article

• Illustrator CS4 Gradient Following a Path

  - by James B

  I'm trying to draw a power cable in illustrator, I want the cable to have one side dark and the other light with a gradient in the middle, because the cable has curved corners it won't work the usual way. I have tried making an art brush with a gradient in it which definitely didn't give me the effect I was looking for. Do you know anyway I can solve this problem?

  Read the article

• Junos custom-attack signature pattern syntax

  - by James Hawkwind

  I am stuck at a point with the configuration of a custom-attack signature in Junos. According to the Junos Custom Attack Definition documentation page, I can set up a custom attack based upon a signature in the packet. In the documentation you can specify a "pattern" to match, but it fails to describe what the pattern syntax should be. Particularly, I want to match the HEX values of 8C 00 13 00 in the first four bytes of the TCP data payload. Does anyone know how to accomplish this correctly?

  Read the article

• PHP on Server 2003: Enabling PHP_APC.DLL creates Error

  - by james.527.

  When trying to enable PHP_APC.DLL, PHP crashes returning invalid access to memory location. Any ideas? I am running 5.2.12 in ISAPI mode. Here is what I have enabled extension wise: ;extension=php_bz2.dll ;extension=php_curl.dll ;extension=php_dba.dll ;extension=php_dbase.dll ;extension=php_exif.dll ;extension=php_fdf.dll extension=php_gd2.dll ;extension=php_gettext.dll ;extension=php_gmp.dll ;extension=php_ifx.dll ;extension=php_imap.dll ;extension=php_interbase.dll extension=php_ldap.dll ;extension=php_mbstring.dll extension=php_mcrypt.dll ;extension=php_mhash.dll ;extension=php_mime_magic.dll ;extension=php_ming.dll ;extension=php_msql.dll ;extension=php_mssql.dll extension=php_mysql.dll extension=php_mysqli.dll ;extension=php_oci8.dll ;extension=php_openssl.dll extension=php_pdo.dll ;extension=php_pdo_firebird.dll ;extension=php_pdo_mssql.dll extension=php_pdo_mysql.dll ;extension=php_pdo_oci.dll ;extension=php_pdo_oci8.dll ;extension=php_pdo_odbc.dll ;extension=php_pdo_pgsql.dll extension=php_pdo_sqlite.dll ;extension=php_pgsql.dll ;extension=php_pspell.dll ;extension=php_shmop.dll ;extension=php_snmp.dll ;extension=php_soap.dll ;extension=php_sockets.dll extension=php_sqlite.dll ;extension=php_sybase_ct.dll ;extension=php_tidy.dll ;extension=php_xmlrpc.dll ;extension=php_xsl.dll extension=php_zip.dll extension=php_win32service.dll ultimately i'm trying to create a PHP based uploader with a progress bar. From what I understand PHP_APC is the only way to do this. If anyone could help me stabilize PHP_APC or know of another UL with progress bar method, it would be appreciated.

  Read the article

• Windows or Linux for VPN-VPN Bridge

  - by James

  I have the following network layout: Network1 ----VPN1-----Network2----VPN2----Network3 I can administer everything in Network1 only and my goal is to get to a box on Network3. I've been told by the admins of Network2 that it's not possible for them to route traffic from Network1 to Network3. I've finally been authorised to host a box in Network2 and I'm hoping with this I can set something up to resolve the issue. My question is should I set this up as a Windows or a Linux box. My initial thought was to use iptables to reroute requests but with my lack of experience with Windows Server (used for something or other in Network2) I'm not sure if this will work. My head's full of questions like: - can I get an ip without logging in to a windows domain? - if I do get an ip, do Windows Servers manage routing through the VPN? - can I make a linux box authenticate with Windows Server to log on to the domain? - would it just be easier to set up a windows box? - is it possible to configure a windows box to do routing from Network1 to Network3? Has anyone done anything like this before? Had experience managing Windows Server? Authenticated (or not as the case may be) to a Windows domain? I'd really appreciate your advice. It might be worth mentioning that the overall objective is to establish a telnet connection from a box on Network1 to a box on Network3.

  Read the article

• Log Location Url Responses of 301 redirects from IIS

  - by James Lawruk

  Is there a way to log 301 redirects returned by IIS with the (1) request Url and the (2) location Url of the response? Something like this: Url, Location /about-us, /about /old-page, /new-page The IIS logs contain the Request Url and the status code (301), but not the location Url of the response. Ideally there would be an additional field in the IIS Log called Location that would be populated when IIS responded with a 301. In my case the source of the redirect could be ISAPI Rewrite Rules, ASP.NET applications, Cold Fusion applications, or IIS itself. Perhaps there is a way to log IIS response data? Thanks for your help.

  Read the article

• Why does my dd backup of MacBook OS X fail to boot upon restore?

  - by James

  I created a backup of a MacBook hard drive (WD2500BEVS-88US) by hooking it up as a secondary drive on my linux system (Ubuntu 10.10). I used the following command: sudo dd if=/dev/sdc of=/home/backup.img bs=2M This appears to have completed with no errors. I noticed that the file is only 68 GB in size even though the drive is 250 GB in capacity. I restored the image to a spare drive (WD2500BEVS) with the following command: sudo dd if=/home/backup.img of=/dev/sdb bs=2M When I boot the spare drive in the Mac, it appears to start up for a few seconds and then shuts down. (It does not appear to load into the OS at all). When I open up the drive that won't boot in GParted, it looks like this: When looking at the information for the middle partition with the little red exclamation mark, it shows this: The original hard drive that boots ok shows up like this: Further info on both drives: sudo fdisk -l Disk /dev/sdb: 250.1 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdb1 1 30402 244198580 ee GPT WARNING: GPT (GUID Partition Table) detected on '/dev/sdc'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sdc: 250.1 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdc1 1 30402 244198580 ee GPT So why is my backup or restore failing? Why is dd not creating a byte for byte duplicate?

  Read the article

• Certificate Authority issuing Basic EFS certificates without Autoenroll

  - by James Jones

  We have observed some puzzling behavior from the CAs we have set up in both the past and present. For some reason unknown to us, it seems that our CAs are randomly issuing "Basic EFS" certificates to our users. This is evident through the "Issued Certificates" log on the CA. I personally set up a CA yesterday, and the instant that I installed certificate services it started dishing out Basic EFS certs to our users. They seem to be issued at random times: 1:51am, 2:20am, then 7:54am, then 8:03am... etc I looked at the certificate template for Basic EFS and there isn't even an option for Autoenrollment, so I'm seriously in a state of "WTF?!"... Can anyone clue me in as to why my CA has a mind of its own? Do CAs tend to become self-aware and lash out at their owners? Please help...

  Read the article

• Using Ubuntu Karmic as an L2TP Client for VPN

  - by James Lawrie

  I'm trying to connect to a VPN service over L2TP using Karmic as a client and it's not working. The only details I have are the remote IP address, username & password, and a shared secret string; this is enough for Windows but doesn't appear to be enough for Ubuntu. I've tried using network-manager-vpnc and vpnc from the terminal to connect and I get "no supported authentication", and trying with OpenSwan it says "unable to identify either side of the connection". I'd really appreciate some help here if anyone else has implemented this successfully.

  Read the article

• Windows Backup fails with 0x80070002: "The system cannot find the file specified"

  - by James Johnston

  Windows 7 Backup is failing. When backing up even a single insignificant directory (e.g. I chose only the empty "Contacts" directory, leaving all other directories unchecked), I get this error within a few seconds and the backup fails. If I uncheck all files/directories, and just do the system image - then the system image is backed up OK without issue. Backup destination is an external USB hard drive. Steps to reproduce and subsequent failure: Set up backup to go to external hard drive. Don't back up system image. Back up "Contacts" directory only for my profile. Start backup. Immediately view the status of the backup, it stays on "Creating a shadow copy..." for a few seconds, and then the backup fails. Click Options button, and it says "Check your backup / The system cannot find the file specified." - with options to "Try to run backup again" or "Change backup settings". If I click "Show Details", then it says: Backup time: 4/12/2012 04:38 Backup location: My Book (D:) Error code: 0x80070002 An examination of the Event Log shows nothing useful beyond the following: Log Name: Application Source: Windows Backup Date: 4/12/2012 04:38:44 Event ID: 4104 Task Category: None Level: Error Keywords: Classic User: N/A Computer: JTJLaptop Description: The backup was not successful. The error is: The system cannot find the file specified. (0x80070002). Event Xml: <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event"> <System> <Provider Name="Windows Backup" /> <EventID Qualifiers="0">4104</EventID> <Level>2</Level> <Task>0</Task> <Keywords>0x80000000000000</Keywords> <TimeCreated SystemTime="2012-04-12T04:38:44.000000000Z" /> <EventRecordID>23979</EventRecordID> <Channel>Application</Channel> <Computer>JTJLaptop</Computer> <Security /> </System> <EventData> <Data>The system cannot find the file specified. (0x80070002)</Data> <Binary>02000780E30500003F0900005B090000420ED1665C2BEE174B64529CB14610EA71000000</Binary> </EventData> </Event> What I have tried: ChkDsk on both C: (main drive) and D: (backup drive) doesn't find any errors. Running SFC /SCANNOW to run system file checker Checked the list of profiles at HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\ProfileList and ensured that each profile directory exists. I'm stumped; WHAT file can't be found and why is my backup failing? This is on a Lenovo T420 laptop.

  Read the article

• /scripts/easyapache broke PHP and now outputs binary

  - by James Lawrie

  I ran /scripts/easyapache on one of my cpanel servers last night and since then PHP just gives 501 errors, which no logs I can find. I tried running it again and it's running as normal but all output has been replaced with strange characters, eg: ????+?+± °?? ?-?.?... =?? ????+?+± °?? ¦+?+?.?... =?? ????+?+± °?? ?=?/¦+?+?.?... +? ????+?+± °?? ?=?/??++.?... =?? ????+?+± °?? ??++.?... =?? ????+?+± °?? ???+?+.?... +? ????+?+± °?? ?=?/????¦???.?... =?? ????+?+± °?? +??±?+.?... =?? ????+?+± °?? +??¦+?.?... =?? Has anyone come across this before? Is it fixable?

  Read the article

• How to back up non-standard directories in my user profile with Windows Backup?

  - by James Johnston

  I'm using Windows Backup to back up my Win7 Pro laptop. I'd like to use it to back up my complete user profile, but I only see standard profile directories (e.g. C:\Users\JohnstonJ\Documents) in the list. Non-standard ones aren't there (e.g. C:\Users\JohnstonJ\MyCustomDirectory). What's the best way to handle this? The only thing I can think of is to browse under the "Computer" entry and navigate directly to C:\Users\JohnstonJ and check off the entire profile (to get what's in there, and any new directories that come up). But is that going to back up the profile twice? Cause other unforeseen problems given that I checked it off by navigating through the computer, rather than picking it under the "Data Files" category? (e.g. back up temporary file garbage, files in use problems, etc. that the "Data Files" category might be handling better). Looking for solutions that other people use that are known to work well and still uses the Windows Backup software - I don't really want to fuss with 3rd-party backup software. Example - as you can see, I have two directories in my profile that Windows Backup is not offering to back up: "Dropbox" and "New folder": (Link to images album because I don't have enough reputation to directly embed them: http://imgur.com/a/Xyv5u)

  Read the article

• SQL Server 2005 to 2008 upgrade - are MDF files binary compatible?

  - by james

  I have 50 databases on a MS SQL Server 2005 system and want to upgrade to MS SQL Server 2008. This is what I tried on some test machines: 1. copied the \DATA directory from the source (MSSQL 2005) to exactly the same path on the target (MSSQL 2008) server. 2. edited the startup parameters on the MSSQL 2008 service to point to the path of the MSSQL 2005 master database. 3. restarted MSSQL service It worked and I can access all databases, tables and data. My questions are: I go back to SQL Server 4.2 and it has never been this easy. I know it worked, but should have it worked? Am I missing something, or is there going to be a gotcha next week? These are simple databases, with just tables, views and indexes. No cross database links, no triggers etc

  Read the article

• Debug Apache mod_status showing 151 requests/sec - 2.7 GB/second

  - by James Hackett

  One of my web servers went crazy this morning and showed "151 requests/sec - 2.7 GB/second - 140.7 MB/request" the normal is like "11.1 requests/sec - 65.6 kB/second - 5.9 kB/request" I don't even think that kind of through put is possible on my server. It was also listing odd symbols for the urls and the amount of data transfered for connections was off the meter 246-0 -1286402072 0/0/0 ? 0.00 -1444841118 0 -5416403825852416.0 0.00 0.00 °Rk³ 247-0 18 0/0/0 ? -13112985.76 2094967848 0 -5428200825946112.0 0.00 0.00 248-2 23437 0/0/2 _ 0.00 0 0 0.0 0.00 -5340330065920.00 74.53.23.134 web2.mydomain.com OPTIONS / HTTP/1.0 249-2 23279 0/2981898840/0 W 16673317.60 11 0 0.0 2844.06 0.00 201.144.221.245 www.mydomain.com GET /cb8ff49a2395a7b1accbbce1e4cf164f/view/256 HTTP/1.1 250-0 0 40600/3009863336/0 ? 3816369.92 910209710 0 2913775.3 -5323551899648.00 -5324315849947.28 èøϲ Has anyone seen anything like this before and know what might be causing it? I posted the full mod_status output here http://pastie.org/916066

  Read the article

• What are the right reverse PTR, domain keys, and SPF settings for two domains running the same appli

  - by James A. Rosen

  I just read Jeff Atwood's recent post on DNS configuration for email and decided to give it a go on my application. I have a web-app that runs on one server under two different IPs and domain names, on both HTTP and HTTPS for each: <VirtualHost *:80> ServerName foo.org ServerAlias www.foo.org ... </VirtualHost> <VirtualHost 1.2.3.4:443> ServerName foo.org ServerAlias www.foo.org </VirtualHost> <VirtualHost *:80> ServerName bar.org ServerAlias www.bar.org ... </VirtualHost> <VirtualHost 2.3.4.5:443> ServerName bar.org ServerAlias www.bar.org </VirtualHost> I'm using GMail as my SMTP server. Do I need the reverse PTR and SenderID records? If so, do I put the same ones on all of my records (foo.org, www.foo.org, bar.org, www.bar.org, ASPMX.L.GOOGLE.COM, ASPMX2.GOOGLEMAIL.COM, ..)? I'm pretty sure I want the domain-keys records, but I'm not sure which domains to attach them to. The Google mail servers? foo.org and bar.org? Everything?

  Read the article

• Unzip individual files from multiple zip files and extract those individual files to home directory

  - by James P.

  I would like to unzip individual files. These files have a .txt extension. These files also live within multiple zipped files. Here is the command I'm trying to use. unzip -jn /path/to/zipped/files/zipArchiveFile2011\*.zip /path/to/specific/individual/files/myfiles2011*.txt -d /path/to/home/directory/for/extract/ From my understanding, the -j option excludes directories and will extract only the txt files The -n option will not overwrite a file if it has already been extracted. I've also learned that the forward slash in /path/to/zipped/files/zipArchiveFile2011\*.zip is necessary to escape the wildcard (*) character. Here is sample of error messages I'm coming accross: Archive: /path/to/zipped/files/zipArchiveFile20110808.zip caution: filename not matched: /path/to/specific/individual/files/myfiles20110807.txt caution: filename not matched: /path/to/specific/individual/files/myfiles20110808.txt Archive: /path/to/zipped/files/zipArchiveFile20110809.zip caution: filename not matched: /path/to/specific/individual/files/myfiles20110810.txt caution: filename not matched: /path/to/specific/individual/files/myfiles20110809.txt I feel that I'm missing something very simple. I've tried using single quotes (') and double quotes (") around directory paths. But no luck.

  Read the article

• saslauthd authentication error

  - by James

  My server has developed an expected problem where I am unable to connect from a mail client. I've looked at the server logs and the only thing that looks to identify a problem are events like the following: Nov 23 18:32:43 hig3 dovecot: imap-login: Login: user=, method=PLAIN, rip=xxxxxxxx, lip=xxxxxxx, TLS Nov 23 18:32:55 hig3 postfix/smtpd[11653]: connect from xxxxxxx.co.uk[xxxxxxx] Nov 23 18:32:55 hig3 postfix/smtpd[11653]: warning: SASL authentication failure: cannot connect to saslauthd server: No such file or directory Nov 23 18:32:55 hig3 postfix/smtpd[11653]: warning: xxxxxxx.co.uk[xxxxxxxx]: SASL LOGIN authentication failed: generic failure Nov 23 18:32:56 hig3 postfix/smtpd[11653]: lost connection after AUTH from xxxxxxx.co.uk[xxxxxxx] Nov 23 18:32:56 hig3 postfix/smtpd[11653]: disconnect from xxxxxxx.co.uk[xxxxxxx] The problem is unusual, because just half an hour previously at my office, I was not being prompted for a correct username and password in my mail client. I haven't made any changes to the server, so I can't understand what would have happened to make this error occur. Searches for the error messages yield various results, with 'fixes' that I'm uncertain of (obviously don't want to make it worse or fix something that isn't broken). When I run testsaslauthd -u xxxxx -p xxxxxx I also get the following result: connect() : No such file or directory But when I run testsaslauthd -u xxxxx -p xxxxxx -f /var/spool/postfix/var/run/saslauthd/mux -s smtp I get: 0: OK "Success." I found those commands on another forum and am not entirely sure what they mean, but I'm hoping they might give an indication of where the problem might lie. If it makes any difference, I'm running Ubuntu 10.04.1, Postfix 2.7.0 and Webmin/ Virtualmin.

  Read the article

• Create restricted user on Debian server

  - by James Willson

  I want to create a user account for each of the key programs installed on my debian server. For example, for the following programs: Tomcat Nginx Supervisor PostgreSQL This seems to be recommended based on my reading online. However, I want to restrict these user accounts as much as possible, so that they dont have a shell login, dont have access to the other programs and are as limited as possible but still functional. Would anyone mind telling me how this could be achieved? My reading so far suggests this: echo "/usr/sbin/nologin" >> /etc/shells useradd -s /usr/sbin/nologin tomcat But I think there may be a more complete way of doing it. EDIT: I'm using debian squeeze

  Read the article

• What is causing the unusual high load average and IOwait?

  - by James

  I noticed on Tuesday night of last week, the load average went up sharply and it seemed abnormal since the traffic is small. Usually, the numbers usually average around .40 or lower and my server stuff (mysql, php and apache) are optimized. I noticed that the IOWait is unusually high even though the processes is barely using any CPU. top - 01:44:39 up 1 day, 21:13, 1 user, load average: 1.41, 1.09, 0.86 Tasks: 60 total, 1 running, 59 sleeping, 0 stopped, 0 zombie Cpu0 : 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu1 : 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu2 : 0.0%us, 0.3%sy, 0.0%ni, 99.7%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu3 : 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu4 : 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu5 : 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu6 : 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu7 : 0.0%us, 0.0%sy, 0.0%ni, 91.5%id, 8.5%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 1048576k total, 331944k used, 716632k free, 0k buffers Swap: 0k total, 0k used, 0k free, 0k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 1 root 15 0 2468 1376 1140 S 0 0.1 0:00.92 init 1656 root 15 0 13652 5212 664 S 0 0.5 0:00.00 apache2 9323 root 18 0 13652 5212 664 S 0 0.5 0:00.00 apache2 10079 root 18 0 3972 1248 972 S 0 0.1 0:00.00 su 10080 root 15 0 4612 1956 1448 S 0 0.2 0:00.01 bash 11298 root 15 0 13652 5212 664 S 0 0.5 0:00.00 apache2 11778 chikorit 15 0 2344 1092 884 S 0 0.1 0:00.05 top 15384 root 18 0 17544 13m 1568 S 0 1.3 0:02.28 miniserv.pl 15585 root 15 0 8280 2736 2168 S 0 0.3 0:00.02 sshd 15608 chikorit 15 0 8280 1436 860 S 0 0.1 0:00.02 sshd Here is the VMStat procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 1 0 0 768644 0 0 0 0 14 23 0 10 1 0 99 0 IOStat - Nothing unusal Total DISK READ: 67.13 K/s | Total DISK WRITE: 0.00 B/s TID PRIO USER DISK READ DISK WRITE SWAPIN IO COMMAND 19496 be/4 chikorit 11.85 K/s 0.00 B/s 0.00 % 0.00 % apache2 -k start 19501 be/4 mysql 3.95 K/s 0.00 B/s 0.00 % 0.00 % mysqld 19568 be/4 chikorit 11.85 K/s 0.00 B/s 0.00 % 0.00 % apache2 -k start 19569 be/4 chikorit 11.85 K/s 0.00 B/s 0.00 % 0.00 % apache2 -k start 19570 be/4 chikorit 11.85 K/s 0.00 B/s 0.00 % 0.00 % apache2 -k start 19571 be/4 chikorit 7.90 K/s 0.00 B/s 0.00 % 0.00 % apache2 -k start 19573 be/4 chikorit 7.90 K/s 0.00 B/s 0.00 % 0.00 % apache2 -k start 1 be/4 root 0.00 B/s 0.00 B/s 0.00 % 0.00 % init 11778 be/4 chikorit 0.00 B/s 0.00 B/s 0.00 % 0.00 % top 19470 be/4 mysql 0.00 B/s 0.00 B/s 0.00 % 0.00 % mysqld Load Average Chart - http://i.stack.imgur.com/kYsD0.png I want to be sure if this is not a MySQL problem before making sure. Also, this is a Ubuntu 10.04 LTS Server on OpenVZ. Edit: This will probably give a good picture on the IO Wait top - 22:12:22 up 17:41, 1 user, load average: 1.10, 1.09, 0.93 Tasks: 33 total, 1 running, 32 sleeping, 0 stopped, 0 zombie Cpu(s): 0.6%us, 0.2%sy, 0.0%ni, 89.0%id, 10.1%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 1048576k total, 260708k used, 787868k free, 0k buffers Swap: 0k total, 0k used, 0k free, 0k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 1 root 15 0 2468 1376 1140 S 0 0.1 0:00.88 init 5849 root 15 0 12336 4028 668 S 0 0.4 0:00.00 apache2 8063 root 15 0 12336 4028 668 S 0 0.4 0:00.00 apache2 9732 root 16 0 8280 2728 2168 S 0 0.3 0:00.02 sshd 9746 chikorit 18 0 8412 1444 864 S 0 0.1 0:01.10 sshd 9747 chikorit 18 0 4576 1960 1488 S 0 0.2 0:00.24 bash 13706 chikorit 15 0 2344 1088 884 R 0 0.1 0:00.03 top 15745 chikorit 15 0 12968 5108 1280 S 0 0.5 0:00.00 apache2 15751 chikorit 15 0 72184 25m 18m S 0 2.5 0:00.37 php5-fpm 15790 chikorit 18 0 12472 4640 1192 S 0 0.4 0:00.00 apache2 15797 chikorit 15 0 72888 23m 16m S 0 2.3 0:00.06 php5-fpm 16038 root 15 0 67772 2848 592 D 0 0.3 0:00.00 php5-fpm 16309 syslog 18 0 24084 1316 992 S 0 0.1 0:00.07 rsyslogd 16316 root 15 0 5472 908 500 S 0 0.1 0:00.00 sshd 16326 root 15 0 2304 908 712 S 0 0.1 0:00.02 cron 17464 root 15 0 10252 7560 856 D 0 0.7 0:01.88 psad 17466 root 18 0 1684 276 208 S 0 0.0 0:00.31 psadwatchd 17559 root 18 0 11444 2020 732 S 0 0.2 0:00.47 sendmail-mta 17688 root 15 0 10252 5388 1136 S 0 0.5 0:03.81 python 17752 teamspea 19 0 44648 7308 4676 S 0 0.7 1:09.70 ts3server_linux 18098 root 15 0 12336 6380 3032 S 0 0.6 0:00.47 apache2 18099 chikorit 18 0 10368 2536 464 S 0 0.2 0:00.00 apache2 18120 ntp 15 0 4336 1316 984 S 0 0.1 0:00.87 ntpd 18379 root 15 0 12336 4028 668 S 0 0.4 0:00.00 apache2 18387 mysql 15 0 62796 36m 5864 S 0 3.6 1:43.26 mysqld 19584 root 15 0 12336 4028 668 S 0 0.4 0:00.02 apache2 22498 root 16 0 12336 4028 668 S 0 0.4 0:00.00 apache2 24260 root 15 0 67772 3612 1356 S 0 0.3 0:00.22 php5-fpm 27712 root 15 0 12336 4028 668 S 0 0.4 0:00.00 apache2 27730 root 15 0 12336 4028 668 S 0 0.4 0:00.00 apache2 30343 root 15 0 12336 4028 668 S 0 0.4 0:00.00 apache2 30366 root 15 0 12336 4028 668 S 0 0.4 0:00.00 apache2

  Read the article

< Previous Page | 16 17 18 19 20 21 22 23 24 25 26 27  | Next Page >