Search Results

Search found 11124 results on 445 pages for 'optical drive'.

Page 20/445 | < Previous Page | 16 17 18 19 20 21 22 23 24 25 26 27  | Next Page >

  • zfs pool error, how to determine which drive failed in the past

    - by Kendrick
    I had been copying data from my pool so that I could rebuild it with a different version so that I could go away from solaris 11 and to one that is portable between freebsd/openindia etc. it was copying at 20mb a sec the other day which is about all my desktop drive can handle writing from the network. suddently lastnight it went down to 1.4mb i ran zpool status today and got this. pool: store state: ONLINE status: One or more devices has experienced an unrecoverable error. An attempt was made to correct the error. Applications are unaffected. action: Determine if the device needs to be replaced, and clear the errors using 'zpool clear' or replace the device with 'zpool replace'. see: http://www.sun.com/msg/ZFS-8000-9P scan: none requested config: NAME STATE READ WRITE CKSUM store ONLINE 0 0 0 raidz1-0 ONLINE 0 0 0 c8t3d0p0 ONLINE 0 0 2 c8t4d0p0 ONLINE 0 0 10 c8t2d0p0 ONLINE 0 0 0 it is currently a 3 x1tb drive array. what tools would best be used to determine what the error was and which drive is failing. per the admin doc The second section of the configuration output displays error statistics. These errors are divided into three categories: READ – I/O errors occurred while issuing a read request. WRITE – I/O errors occurred while issuing a write request. CKSUM – Checksum errors. The device returned corrupted data as the result of a read request. it was saying low counts could be any thing from a power flux to a disk event but gave no suggestions as to what tools to check and determine with.

    Read the article

  • Resetting "HDD Warning???" with Zalman ZM-VE400 external case

    - by 0xC0000022L
    Whenever I turn on (or plug in) the Zalman ZM-VE400 I have, it shows HDD Warning???. Sometimes briefly, sometimes until the Menu button is pressed. The case contains a SSD drive and as far as I understand the warning relates to the S.M.A.R.T. status of which this drive doesn't support all parts. How can I reset the warning so I don't receive it every time when turning on the drive? Firmware reports: V400_01_040_N Here's what I have tried so far: Unplug and plug back in Open the case and remove the SSD, then put it back in Press the button on the back side (cover removed) while plugged in Press the button on the back side (cover removed) while not plugged in USB Connect = Refresh = Enter USB Connect = Safe Removal = Enter Advanced = Umount VHDD = Enter

    Read the article

  • How do I execute a file from a FAT USB drive?

    - by Derek Redfern
    I'm trying to install a portable app onto my USB drive such that it is compatible with both Ubuntu and Windows (specifically, a program called eToys). Support is already built into the app for both operating systems - there's etoys.sh for Ubuntu and etoys.exe for Windows. I decided to install onto a FAT drive since that can be read from both systems. This works fine for Windows, but for some reason I cannot execute etoys.sh on Ubuntu. The problem is not with the file - when the whole folder is copied to the local hard drive, the app works great in Ubuntu. But when I try to execute it from the USB, it opens the file in a text editor. I then tried running it from a terminal, but I got the message "Permission denied." I've had the same problem with other executables as well. Is there an easy way to execute things from a USB stick? Thanks! -- Derek

    Read the article

  • Mount an external drive at boot time only if it is plugged in.

    - by Jeremy
    I've got an entry for an external harddrive in my fstab: UUID="680C0FE30C0FAAE0" /jgdata ntfs noatime,rw But sometimes this drive isn't plugged in at boot time. This leaves me half way through a boot, with a prompt to "Continue Waiting, press S or press M" but no keypress has any affect at this stage (including ctrl-alt-delete, not even caps-lock). Short of writing a script to check the output of fdisk -l, how can I mount this drive at boot time only if it is present? It would be handy to have an fdisk entry for this drive, so I can just type mount /jgdata instead of needing a device name.

    Read the article

  • Booting but not rebooting from external USB hard drive, what could be the problem?

    - by user8276
    I have a Dell Inspiron 6400 laptop with a dead internal hard drive controller. It boots perfectly from CD or USB. I therefore removed the internal hard drive and installed Ubuntu 10.10 Maverick onto an external USB hard drive. It boots and runs perfectly when doing a "cold start" of the PC. However, when I choose restart/reboot in the Ubuntu menu (e.g. after an update), I get this error message from the BIOS: "No bootable devices, strike f1 to retry boot, f2 for setup utility, press f5 to run onboard diagnostics". I can make the system boot again by pressing f2 or f5 and exiting the utility without having done anything. Or, I can simply power off the system and do a new "cold start". Does anyone know the likely reason for this problem and how to fix it. It is not a big issue but an annoyance that I would like to fix if possible.

    Read the article

  • Ubuntu 10.10 booting but not rebooting from external USB hard drive, what could be the problem?

    - by user8276
    I have a Dell Inspiron 6400 laptop with a dead internal hard drive controller. It boots perfectly from CD or USB. I therefore removed the internal hard drive and installed Ubuntu 10.10 Maverick onto an external USB hard drive. It boots and runs perfectly when doing a "cold start" of the PC. However, when I choose restart/reboot in the Ubuntu menu (e.g. after an update), I get this error message from the BIOS: "No bootable devices, strike f1 to retry boot, f2 for setup utility, press f5 to run onboard diagnostics". I can make the system boot again by pressing f2 or f5 and exiting the utility without having done anything. Or, I can simply power off the system and do a new "cold start". Does anyone know the likely reason for this problem and how to fix it. It is not a big issue but an annoyance that I would like to fix if possible.

    Read the article

  • Using a degrading corrupted hard disk with a brand new one. Is this ok?

    - by EApubs
    My old 500 GB hard drive started to give bad sectors. Its slowly going down. So, I bought a new 1TB Seagate drive. I first attached the 500GB drive as the first primary drive and installed Windows. I want Windows boot loader to be placed in the old drive so it won't conflict with the Linux system. But the actual Windows system (Including the C drive) is placed on my new hard drive. After this, I attached the new drive as the primary and installed Linux. Now if I want to re install windows, I can do it without any issues by simply setting the old drive as the primary. So the Linux system will be untouched. But is it a good idea to set things like this? Will the old degrading drive have an impact on the new one? The old drive is slower than the new one. Won't I be able to get the maximum speed out of the new drive even when its used to install everything (including the OS)? PS : When I ran the Windows Experience Index, I was using the old drive as the primary. Did it got the hard drive ratings from the old drive? What if I run it now with the new drive as the primary?

    Read the article

  • Prevent a partition on a USB drive auto-mounting in Linux

    - by nomount
    On Linux (Gnome desktop) how do you prevent one of the partitions on an external USB drive auto-mounting when it attached to the machine? I don't just want to prevent the Nautilus window from popping up -- I want that partition not to mount. Fiddling with /etc/fstab is not acceptable, as this is a removable drive that is attached to different machines. I seem to remember that you create a hidden file in the root of the file system, but I can't remember what it's called. Something like: touch /media/usbdisk/.no-mount How do you actually make this work?

    Read the article

  • Windows Installer using usb drive for temp purposes

    - by Douglas Anderson
    When installing apps that are built around Windows Installer, it would appear that it often uses my external usb hard disk (when it's connected) as the temp location while it expands and installs the application (creates a folder off the root with a guid name). Is there anyway to change this so it always defaults to a specific drive? This appears to be the case on Windows Vista and 7, not sure about previous releases. EDIT: Current environment variables look like this: TEMP=C:\Users\<me>\AppData\Local\Temp TMP=C:\Users\<me>\AppData\Local\Temp EDIT: I have a funny suspicion that it's using the drive with the largest available free space.

    Read the article

  • External Hard-Drive Randomly Ejects; Stays On

    - by Kaleb F.
    My 250GB I/O Magic USB external hard-drive randomly disconnects / ejects from the computer after between 2-30 minutes of use. When this happens, the blinking activity light on the front of the hdd turns off; however, the disks can still be heard spinning. Unplugging & replugging in the USB does not reconnect the device and the activity light remains unlit. The only way to continue using it is to flip off then on the power switch of the hdd. The hard-drive was formatted with MBR partition table and 2 NTFS volumes. I recently tried switching to GUID with two Mac OS Extended (Journaled), but the problem remains. This error occurs with my new Macbook Pro with Snow Leopard as well as with my DELL E520 with Windows 7 Ultimate.

    Read the article

  • Windows 7 external 2.5 hard drive read write permissions format

    - by user76918
    Working with Windows 7 professional. While trying to format western digital 250GB sata laptop drive; receiving error not initialized. Went to elevated command line to diskpart to clean all; received error message write protected. Went to Disk Management & Virtual disk drive shows as disk 2 not initialized. No format options available greyed out. Went back to command line tried to see attributes disk is read only. How do I take owner ship to change the permissions & format.

    Read the article

  • How to stop S.M.A.R.T check running for external hard drive

    - by gotqn
    I am using Windows 7 and I have enabled my "S.M.A.R.T" check, too. I have bought an external 1 TB USB hard drive. When it is connected with my computer, it delays my machine initial start with about 4-5 minutes. I was very confused at the begging, then disable the "S.M.A.R.T" check and see that the computer runs normally after restart. So, here is what I want to know: Why the check is turn for the external disk? Is there a way to use the "S.M.A.R.T" check only for my main hard drive? Why it takes 4 to 5 minutes more, as my both hard drives - internal/external are 1 TB?

    Read the article

  • MS SQL Server and "No Hard Drive Space Left"

    - by bobber205
    Got a server running a document delivery system on it. The machine is running extremely poorly (Windows XP). I've checked the regular things, like doing a memtest (turned out fine) and trying to degraf the HDD (not needed). The only thing weird about this machine is that its running MSSQL server. And Symantec Anitvirus. (ugh) Sometimes the machine reports "No hard drive space left". I immediately look at the one hard drive at the machine and it still has 20 gigs left. Each and every time. Could MSSQL server cause this? Could this be tied to the machine's terrible performance? Thanks!

    Read the article

  • Skipping scheduled self-tests and predicting drive EOL

    - by Steve Madsen
    For a few weeks now, smartd has been reporting that it is skipping some of its scheduled self-tests on the weekends: Apr 24 18:29:32 calvin smartd[4758]: Device: /dev/sda, skip scheduled Offline Immediate Test; 40% remaining of current Self-Test. Apr 24 18:29:33 calvin smartd[4758]: Device: /dev/sdb, skip scheduled Offline Immediate Test; 50% remaining of current Self-Test. The drives in this RAID-1 array are set to run an offline test four times a day, a short self-test at 2am every day, and a long self-test on Saturdays at 2am. For some reason, it looks like the long self-test is taking longer, causing the other scheduled tests to be skipped. First question: is this a sign of likely drive failure? Then today, smartd reported that a self-test failed. Here is the output of smartctl -a /dev/sdb: smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.8 family Device Model: ST3250823AS Serial Number: 3ND1GNBC Firmware Version: 3.03 User Capacity: 250,059,350,016 bytes Device is: In smartctl database [for details use: -P show] ATA Version is: 7 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Sun Apr 25 13:15:34 2010 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 84) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 047 039 006 Pre-fail Always - 168450357 3 Spin_Up_Time 0x0003 098 098 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 33 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 9 7 Seek_Error_Rate 0x000f 087 060 030 Pre-fail Always - 654745480 9 Power_On_Hours 0x0032 055 055 000 Old_age Always - 40141 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 51 194 Temperature_Celsius 0x0022 037 062 000 Old_age Always - 37 (0 17 0 0) 195 Hardware_ECC_Recovered 0x001a 047 039 000 Old_age Always - 168450357 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0 202 TA_Increase_Count 0x0032 100 253 000 Old_age Always - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 40131 - # 2 Extended offline Completed: read failure 30% 40129 379795511 # 3 Short offline Completed without error 00% 40084 - # 4 Short offline Completed without error 00% 40060 - # 5 Short offline Completed without error 00% 40036 - # 6 Short offline Completed without error 00% 40013 - # 7 Short offline Completed without error 00% 39990 - # 8 Extended offline Completed without error 00% 39977 - # 9 Short offline Completed without error 00% 39919 - #10 Short offline Completed without error 00% 39895 - #11 Short offline Completed without error 00% 39872 - #12 Short offline Completed without error 00% 39848 - #13 Short offline Completed without error 00% 39824 - #14 Short offline Completed without error 00% 39801 - #15 Extended offline Completed without error 00% 39789 - #16 Short offline Completed without error 00% 39754 - #17 Short offline Completed without error 00% 39732 - #18 Short offline Completed without error 00% 39707 - #19 Short offline Completed without error 00% 39683 - #20 Short offline Completed without error 00% 39660 - #21 Short offline Completed without error 00% 39636 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. Given that this drive is about 4.5 years old, I am probably tempting fate by keeping it in service. SMART doesn't seem to get much respect as a reliable way to predict drive failure. What else can I use to get an early indication of drive failure?

    Read the article

  • Sharing Windows 7 Hard drive with Windows XP Hard drive

    - by Ginzo Milani
    I wish to share my hard drives between my two computers but I seem to be running along some sort of error... my windows XP Computer is picking up my "XGaming" hard drive but when clicked it says access is denied, despite there is no password set up(I followed this: http://www.howtogeek.com/howto/windows-7/share-files-and-printers-between-windows-7-and-xp/) I also tried to share my C and J drives on my windows XP computer but my windows 7 computer doesn't seem to even detect them!

    Read the article

  • Hard drive failure during a move

    - by user52141
    So, odd situation here... I shipped a computer via UPS. The computer was well protected, wrapped in multiple layers of padding and tightly packed to minimize any chance of damage. The package arrived in great condition, no damage to the box at all - it looks like it was handled with utmost care. (And given it was shipped 2nd day express and cost $200 to ship, it had better have been) However, upon unpacking it and turning it on... suddenly the computer is telling us there is no boot device. I've checked everything I can think of and everything points to complete and utter hard drive failure. So - what on earth could cause hard drive failure during shipping?

    Read the article

  • Creating Persistent Drive Labels With UDEV Using /dev/disk/by-path

    - by Matt
    I have a new BackBlaze Pod (BackBlaze Pod 2.0). It has 45 3TB drives and they when I first set it up they were labeled /dev/sda through /dev/sdz and /dev/sdaa through /dev/sdas. I used mdadm to setup three really big 15 drive RAID6 arrays. However, since first setup a few weeks ago I had a couple of the hard drives fail on me. I've replaced them but now the arrays are complaining because they can't find the missing drives. When I list the the disks... ls -l /dev/sd* I see that /dev/sda /dev/sdf /dev/sdk /dev/sdp no longer appear and now there are 4 new ones... /dev/sdau /dev/sdav /dev/sdaw /dev/sdax I also just found that I can do this... ls -l /dev/disk/by-path/ total 0 lrwxrwxrwx 1 root root 10 Sep 19 18:08 pci-0000:02:04.0-scsi-0:0:0:0 -> ../../sdau lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:02:04.0-scsi-0:1:0:0 -> ../../sdb lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:02:04.0-scsi-0:2:0:0 -> ../../sdc lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:02:04.0-scsi-0:3:0:0 -> ../../sdd lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:02:04.0-scsi-0:4:0:0 -> ../../sde lrwxrwxrwx 1 root root 10 Sep 19 18:08 pci-0000:02:04.0-scsi-2:0:0:0 -> ../../sdae lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:02:04.0-scsi-2:1:0:0 -> ../../sdg lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:02:04.0-scsi-2:2:0:0 -> ../../sdh lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:02:04.0-scsi-2:3:0:0 -> ../../sdi lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:02:04.0-scsi-2:4:0:0 -> ../../sdj lrwxrwxrwx 1 root root 10 Sep 19 18:08 pci-0000:02:04.0-scsi-3:0:0:0 -> ../../sdav lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:02:04.0-scsi-3:1:0:0 -> ../../sdl lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:02:04.0-scsi-3:2:0:0 -> ../../sdm lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:02:04.0-scsi-3:3:0:0 -> ../../sdn lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:02:04.0-scsi-3:4:0:0 -> ../../sdo lrwxrwxrwx 1 root root 10 Sep 19 18:08 pci-0000:04:04.0-scsi-0:0:0:0 -> ../../sdax lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:04:04.0-scsi-0:1:0:0 -> ../../sdq lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:04:04.0-scsi-0:2:0:0 -> ../../sdr lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:04:04.0-scsi-0:3:0:0 -> ../../sds lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:04:04.0-scsi-0:4:0:0 -> ../../sdt lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:04:04.0-scsi-2:0:0:0 -> ../../sdu lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:04:04.0-scsi-2:1:0:0 -> ../../sdv lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:04:04.0-scsi-2:2:0:0 -> ../../sdw lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:04:04.0-scsi-2:3:0:0 -> ../../sdx lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:04:04.0-scsi-2:4:0:0 -> ../../sdy lrwxrwxrwx 1 root root 9 Sep 19 18:08 pci-0000:04:04.0-scsi-3:0:0:0 -> ../../sdz I didn't list them all....you can see the problem above. They're sorted by scsi id here but sda is missing...replaced by sdau...etc... So obviously the arrays are complaining. Is it possible to get Linux to reread the drive labels in the correct order or am I screwed? My initial design with 15 drive arrays is not ideal. With 3TB drives the rebuild times were taking 3 or 4 days....maybe more. I'm scrapping the whole design and I think I am going to go with 6 x 7 RAID5 disk arrays and 3 hot spares to make the arrays a bit easier to manage and shorten the rebuild times. But I'd like to clean up the drive labels so they aren't out of order. I haven't figured out how to do this yet. Does anyone know how to get this straightened out? Thanks, Matt

    Read the article

  • Gigabyte GA-970A-UD3 mobo won't boot from USB flash drive

    - by user38586
    I am trying to boot BAMT a Debian flavor via USB on a brand new Gigabyte GA-970A-UD3 motherboard. I tried various flash drive and various OS. I never had this problem with ASUS and MSI. The problem is from Gigabyte hardware. I found that my BIOS is very strict about MBR compatibility. Now I can boot in DOS mode. The flash drive need to be formated as a Win98 Startup disk using HP USB disk storage format tool. Unetbootin menu is booting from USB but won't install BAMT. If I use Windows or Linux diskimager the working MBR is deleted. I tried converting BAMT .img to .iso and it is not booting with Unetbootin. Is it possible to boot BAMT(Debian Linux) from a Win98 DOS command prompt? Maybe there is a way to burn the image and keep the working MBR? If the working MBR is deleted, the flash drive is not recognized at all by the BIOS. This is the info I found that got me booting for the first time in DOS: GB's BIOS will only boot USBs formatted to FAT-32, conforming to normal MBR bootloader. I've seen this before, and surmised that the 'stick-maker' was formatting in ReiserFile, or one of the EXT 'flavors', but no one ever followed up to confirm or deny... Also, if it's putting the bootloader into its own partition - won't work! In the BIOS, on the "Integrated Peripherals" page, the "USB Storage Function" item must be enabled (which should be the default) to allow USB booting... I've put a little work into a 'GB USB booting tutorial', and frankly, I'd just go ahead and finish it up for you, but I really don't want to reboot the several times it will take me to 'firm up' procedural details, and take the BIOS/boot pictures for the post - just noticed VAIL finally went 'public beta', so will be downloading for likely twenty-six hours or so There's likely enough there to test a 'raw DOS boot', just to see if your hardware (especially the USB stick itself) will do it... Some post later: Fixed. Here is a brief summary. Since my ubuntu live usb sticks (2gb kingston and 8gb sandisk sd/usb reader - fat32, created in ubuntu 10.04) would not boot this board even though they would boot my ga-ep45-ud3p, I decided to try bilbat's suggestion with the HP usb boot program. I created the win98 boot disk on the kingston 2gb stick without reformatting. It booted right up. Next, I used windows version of unetbootin to write the ubuntu live cd to the kingston disk. This fired right up and completed the install. Everything seems to be in good order now. Unfortunately I can boot in DOS mode but can't boot BAMT.

    Read the article

  • Windows 7 won't show SATA Hard Drive in My Computer

    - by Darth
    I have clean install of Windows 7 x64 with two SATA hard drives. When I open My Computer, I can see only the drive where Windows are installed (and all partitions), but I don't see the other one. When I go to disk manager, I can see that both drives are detected and the one that I don't see in My Computer is also marked as Primary, but when I right click, the Open and Browse are gray. I also checked drives with gparted on live Ubuntu and they both seem to work correctly, the second drive wasn't marked hidden or anything else. Before installing Windows 7, I had Windows XP, where both drives worked properly.

    Read the article

  • Google Drive have a folder/file in both private and public

    - by Sander
    I've my documents in Google Drive/Docs neatly organised in structured folder system. For not cluttering email inboxes purposes I now would like to share the content of 1 single private folder by putting it in the public directory. If possible I'd like to do this without duplicating the content. Is it possible to organise files in Google Drive to that they have 2 tags/folders attached to them - 1 private and 1 public? Is there another way to quickly share/link a folder to my public folder without actually moving it away from my private to my public folder?

    Read the article

  • Cannot copy files from external hard drive to desktop hard drive in Window 7

    - by Mohammad Reza Selim
    I'm trying to copy some old files from one of my external hard-drives to the hard drive of my desktop PC. Some files can not be copied but giving the error like 'Cannot read from source file or disk'. Those files are videos files (.DAT, .VOB, .MPG) and I watched them all the way through with no issues so the files aren't corrupted. I'm running Windows 7, with admin permissions. Could any one let me know the reason and a solution?

    Read the article

  • How to make local drive available in apache localhost

    - by Ronald Allan
    How can I make my "Drive D:" "Drive E" available in localhost. I'm running apache on my backtrack machine. My default is /var/www/. Every directory I created inside the /var/www/ is available and all working fine. Let's say I created /var/www/PENTEST/ the contents of that PENTEST directory can be accessed through: localhost/PENTEST/ How can I make this work: localhost/media/DATA/ The /media/DATA/ is my DRIVE D: I edited this: ServerAdmin webmaster@localhost DocumentRoot /media/DATA/ <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /media/DATA/> Options Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> Still not working. I'm getting 404. # # I figured it out. Thank for the post of "RiggsFolly" which can be found here: http://forum.wampserver.com/read.php?2,89163. I just have to change this: ServerAdmin webmaster@localhost DocumentRoot /media/DATA/ <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /media/DATA/> Options Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> Into this: ServerAdmin webmaster@localhost DocumentRoot D:/media/DATA/ <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory D:/media/DATA/> Options Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory>

    Read the article

  • Windows system drive letter changed after repair install

    - by taffer
    yesterday I did a repair install, because Windows froze on welcome screen after resizing its partition on a dual boot system. corresponding question Everything worked fine so far, but now I am facing another challenge: The Windows drive letter changed from G: to C:, so that most programs, including drivers, firewall and virus scanner do not work anymore. I tried to reinstall the virus scanner, but the uninstaller said, that drive G: is not available. What to do now, to get all programs running again? Is it possible, to rename C: to G: or will that mess up my system?

    Read the article

  • Can't initialize drive in Windows 7

    - by Abe
    I have a 2.5" laptop harddrive that I plugged into my laptop through a SATA to USB cable. It's powered by an adapter to a normal wall-plug. I want to use it as an external harddrive. It wouldn't initialize (Device is not ready), so as suggested in some instructions I found I uninstalled the drivers, unplugged it and plugged it back in. That worked, and I initialized the drive and formatted it. However I unplugged it after that and a few days later the same strategy does not work and I can't figure out how to use the drive. I can't initialize it and it doesn't show up in my computer.

    Read the article

  • Looking for a laptop with a removable hard drive

    - by anno
    At the moment, I possess a Dell Inspiron 6400. Just removing two screws, I've made the drive removable (look here) and I can pull it off in one second. The new Inspiron and Studio laptops don't support this anymore (the drive is no more on the side but on the back of the laptop). So I’m looking for a new laptop having this kind of feature, or one that can be modded easily. I also need a : Screen = 15" (if possible resolution 1366 x 768 resolution) Core i5-520M Midrange GPU (like an ATI Mobility Radeon HD 5650) Decent battery life minimum fan noise Thanks.

    Read the article

< Previous Page | 16 17 18 19 20 21 22 23 24 25 26 27  | Next Page >