Search Results

Search found 8199 results on 328 pages for 'ejb module'.

Page 201/328 | < Previous Page | 197 198 199 200 201 202 203 204 205 206 207 208  | Next Page >

• Random flickering on 2.6.32 kernels after suspend

  - by whitequark

  I have XUbuntu 9.10 installed on a Toshiba NB200 netbook with Intel video card that's handled with i915 driver. With 2.6.31 stable, recommended kernel everything but WiFi works fine: Atheros ath9k WiFi shows too small signal power and loses packets in 'bursts' sometimes. With 2.6.32-* (I tested -9 to -11 from Ubuntu's kernel unstable ppa) everything works fine just prior to first suspend: echo mem >/sys/power/state. After it random unidentified fullscreen 'one-frame' flickering begins in Xorg, and after a couple of minutes everything eventually hangs while showing filled grey (not white; it is like default button colour) screen; no X keys are working: Ctrl+Alt+Fn don't, blind typing in console too. Magic SysRq still works and I was able to reboot. Also there is one out-of-tree kernel module called omnibook that is required to turn on WiFi and Bluetooth. Any advices?

  Read the article

• Ubuntu 9.10 x86_32 with PAE causes graphics issues, mainly slowness

  - by widgisoft

  I've tried the 64bit version and found I was constantly hitting a brick wall trying to get 32bit stuff to run; I'd previously used PAE on 9.04 without any issues so figured I'd give it a shot. However, on 9.10 it seems PAE or the process of enabling PAE breaks the nvidia drivers/module somewhat as performance is terrible; I can't even enable desktop effects and there's lots of artifacting on random controls. Disabling the pae image and rebooting fixes the issue however I'm then stuck with "only" 2.7Gb of ram and unable to use the full 8gb that's installed. Is there somthing special I need to do when using pae and nVidia drivers or should I be using 64bit and just figure out how to force run 32bit packages? :-p

  Read the article

• Rate-Limit affects All clients or single IP?

  - by Asad Moeen

  Well up-til now I've considered iptables rate-limit commands with the "recent" module to work for each IP Address. For example rate-limit rule of 20k/s will trigger only if a single IP exceeds 20k/s rate and not if 4 different IPs exceed 5k/s rate. Please correct me if I considered this wrong as I've only used these rules for TCP/ UDP. But today I tried similar rules for ICMP and applied 4/s Input/Output. But then on trying to ping-test from just-ping.com I could see packet loss on almost all IP Addresses. How could that happen because if it worked for each IP Address then it wouldn't be triggering the rule because I believe each IP from just-ping has a rate of probably 1/s. I still think the first one is true because if it wasn't then my GameServer would block everyone if the combined rate ( in case of more connected players ) increased the threshold. This hasn't happened up til now so the ICMP thing really confused me. Thank you.

  Read the article

• PowerShell fomat.ps1xml not reachable

  - by blsub6

  I'm trying to load Exchange Management Shell and it gives me a big 'ol red error that says: Import-Module : There were errors in loading the format data file: Microsoft.PowerShell, , %APPDATA%\Roaming\Microsoft\Exchange\RemotePowerShell\DOMAINNAME.format.ps1xml : File skipped because of the following validation exception: File %APPDATA%\Roaming\Microsoft\Exchange\RemotePowerShell\DOMAINNAME.format.ps1xml cannot be loaded. The file %APPDATA%\Roaming\Microsoft\ExchangeRemotePowerShell\DOMAINNAME\DOMAINNAME.format.ps1xml is not digitally signed. The script will not execute on the system. Please see "get-help about_signing" for more details... The %APPDATA% is stored on an external server on my network (that I can ping to without problems). I am missing a ton of PS cmdlets too, which I'm presuming are stored in '*.format.ps1xml' I tried finding the directory in which format.ps1xml is supposed to reside on the external server and it's not even created. Can someone tell me where to start?

  Read the article

• Load balance between two virtual directories on a single machine running IIS6

  - by Emil Lerch

  I'm trying to simulate a production environment using a single VM. The production environment will have 3 servers behind a load balancer with sticky sessions. Production will be using IIS6. For development, I have no need to distribute load, but I want to make sure the team does not write code that relies on a single-server module. I have been hoping to set up two virtual directories and find some isapi filter to perform some rudimentary software load balancing, but I've been unable to locate anything suitable. isapi_rewrite comes close but there's no ability for a random rewrite. I don't even need sticky sessions since the application does not (in theory) rely on them. Is there something easy/free to do this, or am I stuck with multiple VMs and a NLB setup (which seems like total overkill)?

  Read the article

• Free IP address management software

  - by TiFFolk

  We are choosing a system for managing our IP address space. So we are looking for a special free software like IPPlan. So what we have nowadays: Ipplan (Beta IPv6 support) SolarWinds IP address tracker (IPv6 support unknown ) IP module of The NOC Project (BTW, take a look of it, seems to be very promising project) (IPv6 support unknown ) phpIP (Does not support IPv6) IP management from RackTables (Does not support IPv6) Do you know about any other special software, like written above? But: No Wiki No DNS No DHCP No spreadsheet Software should provide: Clear view of available addresses Detail listing of all addresses by subnets/search pattern/owners/additional info It must support adding additional info like owner of IP, domain-name, contacts, etc Multi user support Easy interface Software has to be specially written for address management. Scalability Any OS: win, lin, sol, web

  Read the article

• Can't deploy rails 4 app on Bluehost with Passenger 4 and nginx

  - by user2205763

  I am at Bluehost (dedicated server) trying to run a rails 4 app. I asked to have my server re-imaged, specifying that I do not want rails, ruby, or passenger install automatically as I wanted to install the latest versions myself using a version manager (Bluehost by default offers rails 2.3, ruby 1.8, and passenger 3, which won't work with my app). I installed ruby 1.9.3p327, rails 4.0.0, and passenger 4.0.5. I can verify this by typing, "ruby -v", "rails -v", and "passenger -v" (also "gem -v"). I made sure to install these not as root, so that I don't get a 403 forbidden error when trying to deploy the app. I installed passenger by typing "gem install passenger", and then installed the nginx passenger module (into "/nginx") with "passenger-install-nginx-module". I am trying to run my rails app on a subdomain, http://development.thegraduate.hk (I am using the subdomain to show my client progress on the website). In bluehost I created that subdomain, and had it point to "public_html/thegraduate". I then created a symlink from "rails_apps/thegraduate/public" to "public_html/thegraduate" and verified that the symlink exists. The problem is: when I go to http://development.thegraduate.hk, I get a directory listing. There is nothing resembling a rails app. I have not added a .htaccess file to /rails_apps/thegraduate/public, as that was never specified in the installation of passenger. It was meant to be 'install and go'. When I type "passenger-memory-status", I get 3 things: - Apache processes (7) - Nginx processes (0) - Passenger processes (0) So it appears that nginx and passenger are not running, and I can't figure out how to get it to run (I'm not looking to have it run as a standalone server). Here is my nginx.conf file (/nginx/conf/nginx.conf): #user nobody; worker_processes 1; #error_log logs/error.log; #error_log logs/error.log notice; #error_log logs/error.log info; #pid logs/nginx.pid; events { worker_connections 1024; } http { passenger_root /home/thegrad4/.rbenv/versions/1.9.3-p327/lib/ruby/gems/1.9.1/gems/passenger-4.0.5; passenger_ruby /home/thegrad4/.rbenv/versions/1.9.3-p327/bin/ruby; include mime.types; default_type application/octet-stream; #log_format main '$remote_addr - $remote_user [$time_local] "$request" ' # '$status $body_bytes_sent "$http_referer" ' # '"$http_user_agent" "$http_x_forwarded_for"'; #access_log logs/access.log main; sendfile on; #tcp_nopush on; #keepalive_timeout 0; keepalive_timeout 65; #gzip on; server { listen 80; server_name development.thegraduate.hk; root ~/rails_apps/thegraduate/public; passenger_enabled on; #charset koi8-r; #access_log logs/host.access.log main; location / { root html; index index.html index.htm; } #error_page 404 /404.html; # redirect server error pages to the static page /50x.html # error_page 500 502 503 504 /50x.html; location = /50x.html { root html; } # proxy the PHP scripts to Apache listening on 127.0.0.1:80 # #location ~ \.php$ { # proxy_pass http://127.0.0.1; #} # pass the PHP scripts to FastCGI server listening on 127.0.0.1:9000 # #location ~ \.php$ { # root html; # fastcgi_pass 127.0.0.1:9000; # fastcgi_index index.php; # fastcgi_param SCRIPT_FILENAME /scripts$fastcgi_script_name; # include fastcgi_params; #} # deny access to .htaccess files, if Apache's document root # concurs with nginx's one # #location ~ /\.ht { # deny all; #} } # another virtual host using mix of IP-, name-, and port-based configuration # #server { # listen 8000; # listen somename:8080; # server_name somename alias another.alias; # location / { # root html; # index index.html index.htm; # } #} # HTTPS server # #server { # listen 443; # server_name localhost; # ssl on; # ssl_certificate cert.pem; # ssl_certificate_key cert.key; # ssl_session_timeout 5m; # ssl_protocols SSLv2 SSLv3 TLSv1; # ssl_ciphers HIGH:!aNULL:!MD5; # ssl_prefer_server_ciphers on; # location / { # root html; # index index.html index.htm; # } #} } I don't get any errors, just the directory listing. I've tried to be as detailed as possible. Any help on this issue would be greatly appreciated as I've been stumped for the past 3 days. Scouring the web has not helped as my issue seems to be specific to me. Thanks so much. If there are any potential details I forgot to specify, just ask. ** ADDITIONAL INFORMATION ** Going to development.thegraduate.hk/public/ will correctly display the index.html page in /rails_apps/thegraduate/public. However, changing root in the routes.rb file to "root = 'home#index'" does nothing.

  Read the article

• snmptt not translating traps, even with translate_log_trap_oid=1

  - by mbrownnyc

  I am having some trouble configuring snmptt to properly translate snmp traps. The following is a problem: /etc/snmp/snmptt.conf reflects: EVENT fgFmTrapIfChange .1.3.6.1.4.1.12356.101.6.0.1004 "Status Events" Critical FORMAT $* EXEC /usr/local/nagios/libexec/eventhandlers/submit_check_result $r "snmp_traps" 2 "$O: $+*" "$*" SDESC Trap is sent to the managing FortiManager if an interface IP is changed Variables: 1: fnSysSerial 2: ifName 3: fgManIfIp 4: fgManIfMask EDESC when a trap is received, /var/log/messages reflects: Sep 6 12:07:32 SNMPMANAGERHOST snmptrapd[15385]: 2012-09-06 12:07:32 <UNKNOWN> [UDP: [192.168.100.2]:162->[192.168.100.31]]: #012.1.3.6.1.2.1.1.3.0 = Timeticks: (707253943) 81 days, 20:35:39.43 #011.1.3.6.1.6.3.1.1.4.1.0 = OID: .1.3.6.1.4.1.12356.101.6.0.1004 #011.1.3.6.1.4.1.12356.100.1.1.1.0 = STRING: FGTNNNNNNNNN #011.1.3.6.1.2.1.31.1.1.1.1.10 = STRING: internal4 #011.1.3.6.1.4.1.12356.101.6.2.1.0 = IpAddress: 192.168.65.100 #011.1.3.6.1.4.1.12356.101.6.2.2.0 = IpAddress: 255.255.255.0 Sep 6 12:07:37 SNMPMANAGERHOST icinga: EXTERNAL COMMAND: PROCESS_SERVICE_CHECK_RESULT; 192.168.100.2; snmp_traps; 2; enterprises.12356.101.6.0.1004: enterprises.12356.100.1.1.1.0:FGTNNNNNNNNN ifName.10:internal4 enterprises.12356.101.6.2.1.0:192.168.65.100 enterprises.12356.101.6.2.2.0:255.255.255.0 Since the icinga entry reflects the EXEC, it's obvious there is no translations occurring by snmptt. I have verified that translate_log_trap_oid and net_snmp_perl_enable is enabled in snmptt.ini When using --debug=1 to start snmptt, I see the following in the --debugfile: ********** Net-SNMP version 5.05 Perl module enabled ********** The main NET-SNMP version is reported as NET-SNMP version: 5.5. What else can be done to verify that snmptt is configured properly to translate traps? I have run snmptt-net-snmp-test to verify whatever net-snmp-perl version I have installed properly supports translations. The output indicates it does. /root/snmptt_1.3/snmptt-net-snmp-test --best_guess=2 SNMPTT Net-SNMP Test v1.0 (c) 2003 Alex Burger http://snmptt.sourceforge.net MIBS:RFC1213-MIB best_guess: 2 Testing translateObj ******************** Testing: .1.3.6.1.2.1.1.1, long_names=disabled, include_module=disabled Test passed. Result: sysDescr Testing: .1.3.6.1.2.1.1.1, long_names=disabled, include_module=enabled Test passed. Result: RFC1213-MIB::sysDescr Testing: .1.3.6.1.2.1.1.1, long_names=enabled, include_module=disabled Test passed. Result: .iso.org.dod.internet.mgmt.mib-2.system.sysDescr Testing: .1.3.6.1.2.1.1.1, long_names=enabled, include_module=enabled Test passed. Result: RFC1213-MIB::.iso.org.dod.internet.mgmt.mib-2.system.sysDescr Testing: sysDescr, long_names=disabled, include_module=disabled Test passed. Result: .1.3.6.1.2.1.1.1 Testing: RFC1213-MIB::sysDescr, long_names=disabled, include_module=disabled Test passed. Result: .1.3.6.1.2.1.1.1 Testing: system.sysDescr, long_names=disabled, include_module=disabled Test passed. Result: .1.3.6.1.2.1.1.1 Testing: RFC1213-MIB::system.sysDescr, long_names=disabled, include_module=disabled Test passed. Result: .1.3.6.1.2.1.1.1 Testing: .iso.org.dod.internet.mgmt.mib-2.system.sysDescr, long_names=disabled, include_module=disabled Test passed. Result: .1.3.6.1.2.1.1.1 Testing getType *************** Testing: .1.3.6.1.2.1.4.1 Test passed. Result: INTEGER Testing: ipForwarding Test passed. Result: INTEGER Testing Description ******************* Test passed. Result: ------------------------------------------------- The indication of whether this entity is acting as an IP gateway in respect to the forwarding of datagrams received by, but not addressed to, this entity. IP gateways forward datagrams. IP hosts do not (except those source-routed via the host). Note that for some managed nodes, this object may take on only a subset of the values possible. Accordingly, it is appropriate for an agent to return a `badValue' response if a management station attempts to change this object to an inappropriate value. ------------------------------------------------- I have manually gone through the MIB with the definition that's not resolving, and verified that it is properly linking back to the proper resolved definition. It is: FORTINET-FORTIGATE-MIB.txt contains: fgFmTrapIfChange NOTIFICATION-TYPE OBJECTS { fnSysSerial, ifName, fgManIfIp, fgManIfMask } STATUS current DESCRIPTION "Trap is sent to the managing FortiManager if an interface IP is changed" ::= { fgFmTrapPrefix 1004 } fgFmTrapPrefix OBJECT IDENTIFIER ::= { fgMgmt 0 } fgMgmt OBJECT IDENTIFIER ::= { fnFortiGateMib 6 } fnFortiGateMib ::= { fortinet 101 } IMPORTS FnBoolState, FnIndex, fnAdminEntry, fnSysSerial, fortinet FROM FORTINET-CORE-MIB fortinet MODULE-IDENTITY ::= { enterprises 12356 } LOOKS GOOD!!!!! 1.3.6.1.4.1.12356.101.6.0.1004 I've exhausted all the documentation and even posted fruitlessly in the snmptt-users mailing list. I can not prove it is the MIB. Why would snmptt fail to translate traps? Thanks, Matt

  Read the article

• centos how to install systemtap

  - by Mingfei.hua

  I'm really new to sysmtemtap. just want to install and try systemtap on my lab server. My Linux release version is centos 6.3 and kernel version 2.6.32-279.5.2.el6.i686. I followed some doument, do yum install kernel-devel yum install kernel-debuginfo yum install systemtap all completed without error or warning. but when I try to test systemtap by stap -v -e 'probe vfs.read {printf("read performed\n"); exit()}' I got error Pass 1: parsed user script and 83 library script(s) using 25180virt/14088res/2684shr kb, in 120usr/10sys/161real ms. semantic error: missing i386 kernel/module debuginfo under '/lib/modules/2.6.32-279.5.2.el6.i686/build' while resolving probe point kernel.function("vfs_read")

  Read the article

• Can SATA be used to connect computers?

  - by André

  Can SATA be used to connect two computers together, just like a crossover Ethernet cable would do ? I know SATA has no "networking" features and even though a controller may have multiple ports, the drives don't "see" each other, and that in SATA one device acts as the host (the computer) and the other device is some kind of "client" (the storage drive). But still, did anyone attempt to make a kernel module that would make one computer appear as a "client" (so that the host's SATA controller detects it as a standard hard drive) and then set up like a pseudo-Ethernet link or a very high speed serial link (and then run pppd on it and do networking) ? Note : I know this is an unprofessional and totally stupid idea, I'm just asking out of curiosity.

  Read the article

• Logging Apache2 payload to evaluate SOAP message

  - by Phil

  I am trying to log webservice specific information with Apache (Apache acts as a load-balancer by use of mod_jk). For instance I want to know how long the responsetime of each webservice-call takes. To do this I definitely would need to know the name of the webservice-method in the log-file. As a matter of fact, the name of the webservice-method is wrapped in the SOAP-body, to which I have no access to with the default-configuration. Does anybody know an Apache module to extend the log-information? Or are there any other ideas to solve this challenge? Thx!

  Read the article

• Use AssignUserId as variable in Apache MPM ITK

  - by Robert Hanson

  I heard that the MPM-ITK module for Apache can change Apache server's behaviour to access some folder / file using the UID or GID from the default UID (www-data) into a given UID on the configuration. For example: <IfModule mpm_itk_module> AssignUserId user group </IfModule> Is it possible to make the username and group a variable? I want to make Apache access the /home folder as its owner. For example /home/me can only be accessed by the user me, while /home/you can only be accessed you.

  Read the article

• How to create iso dvd image for use with Mac OS X's "Disk Utility"?

  - by adolf garlic

  This seemed way easier on my pc. I would just pop a blank dvd in the drive, it asked what I wanted to do with it, to which I would respond, "burn dvd with nero" (paraphrasing), then I would pick "new" and just drag and drop the folders in there. Mac appears to have "Disk Utility" which just requires that I 'choose an image' but then doesn't bother to detail: how to do this what the options mean e.g. format "Mac OS Extended (Journaled)" is that ever going to be readable on a non Mac machine? I want to create an ISO standard DVD as per the 'default' you'd get on nero. All the stuff on the web points to doing things with 'Terminal' (the whole point of buying a Mac was to get away from command line jiggery pokery - I'm trying to burn some photos not land a friggin lunar module here!) Please, if you can just provide some simple instructions on what I need to achive this I'd be extremely grateful. Ta muchley in advance.

  Read the article

• Enabling ppolicy in openldap

  - by nitins

  For enabling ppolicy is in Openldap I am trying to import the policy given below. dn: ou=policies,dc=example,dc=in ou: policies objectClass: top objectClass: organizationalUnit # default, policies, example.in dn: cn=default,ou=policies,dc=example,dc=in objectClass: top objectClass: device objectClass: pwdPolicy cn: default pwdAttribute: userPassword pwdMaxAge: 7776002 pwdExpireWarning: 432000 pwdInHistory: 0 pwdCheckQuality: 1 pwdMinLength: 8 pwdMaxFailure: 5 pwdLockout: TRUE pwdLockoutDuration: 900 pwdGraceAuthNLimit: 0 pwdFailureCountInterval: 0 pwdMustChange: TRUE pwdAllowUserChange: TRUE pwdSafeModify: FALSE But I am getting the error given below. ldapadd -x -D "cn=Manager,dc=example,dc=in" -w xxxxxx -f /tmp/new-policy.ldif adding new entry "cn=default,ou=policies,dc=example,dc=in" ldapadd: Invalid syntax (21) additional info: pwdAttribute: value #0 invalid per syntax Any idea on why I am getting the error ? I have already added the ppolicy schema and module in slapd.conf

  Read the article

• LameUser trying - apache2 webserver authentication - IP range to access without pass prompt others with it

  - by Mikee

  I have (maybe silly) question regarding the apache2 webserver and security - I am trying to archieve this: Users connecting from 192.168.1.24 not to be prompted for password and allowed Others asked for username and password if correct then connect. I am trying to do this for the whole directory /var/www No matter whether I put the code into .htaccess file or in httpd.conf it doesn't work for me. Order deny,allow Deny from all AuthName "PassRequest" AuthType Basic AuthUserFile /var/.htpasswd Require valid-user Allow from 192.168.1.24 Satisfy Any If I try to connect to the page I am allowed from both the allowed IP or any other, If I remove the satisfy any line then I am prompted for password, if I remove the password too and try to connect from different IP I am NOT REFUSED ... is there some module that needs to be activated or why is the IP directive skipped ? It needs to be put in every folder or /var/www/.htaccess is enough ? can I just put it in httpd.conf instead or not ?? I spend last 4 hours trying to google up why it is acting like that, Any help will be highly appreciated :-))

  Read the article

• How to create public html (apache2) with LDAP authentication?

  - by borjamf

  Im running Apache2 on Ubuntu 12.04 Server because I want to create a home directory for each ldap user. I'm using LDAP for authentication and it's working ok. Also I've done some tests with LDAP module for Apache2 and it's working ok. The problem with this LDAP authentication is that any success login can access to ~user/public_html, even if the user is not the owner of that home. I dont know how to control that, for example, userldap2 access to userldap1/public_html. I want that only the userldap1 access to userldap1. Could anybody tell me how to control that with LDAP authentication? I hope that you'll understand me. My config (auth_ldap.conf) <Directory /home/disco2/*/public_html> AuthName "Authentication" AuthType basic AuthBasicProvider ldap AuthzLDAPAuthoritative off AuthLDAPURL ldap://prueba.borja/dc=prueba,dc=borja?uid? Require ldap-filter objectClass=posixAccount </Directory>

  Read the article

• How to automate kinit process to obtain TGT for Kerberos?

  - by tore-

  I'm currently writing a puppet module to automate the process of joining RHEL servers to an AD domain, with support for Kerberos. Currently I have problems with automatically obtain and cache Kerberos ticket-granting ticket via 'kinit'. If this were to be done manually, I would do this: kinit [email protected] This prompts for the AD user password, hence there is a problem with automate this. How can i automate this? I've found some posts mentioning using kadmin to create a database with the ad users password in it, but I've had no luck. Thanks for input

  Read the article

• HELP! need to make a VoIP program for WiMAX in NS-2 work..

  - by janiemack

  I've been trying to get this working for the past 2 days and i'm completely stuck. I'm trying to make a simple VoIP program work in the NIST module for WiMAX http ://community.4gdeveloper.com/attachments/download/14/090720150504_ns2-Release-2.6.tar.gz version 2.6 , using NS-2.31 (remove space btw 'p' and ':' ) http ://downloads.sourceforge.net/nsnam/ns-allinone-2.31.tar.gz?modtime=1173548159&big_mirror=0 (remove space btw 'p' and ':' ) The installation process goes fine. When i run this program, I'm getting an error saying " OFDMAPhy : error did not find match for permutation and bw combination" Some help would be really appreciated. thanks!

  Read the article

• Usermin (Webmin)- Users can't login

  - by Armadillo

  I've installed Webmin in my server. The users of my Unix server must be able to change their passwords. So, for that, they use Usermin. But users just can't login in Usermin module. I get always this message: Login failed. Please try again. What is the reason for this behavior? How can I give access to Usermin to my users? I'm able to login as any user when viewing "Current Login Sessions" - "Switch to Usermin user:", with the Admin user.

  Read the article

• OpenAFS on Fedora/CentOS

  - by Michael Pliskin

  I am trying to see if OpenAFS fits my needs as a distributed filesystem and is a bit stuck. There are docs but they're all quite hard to understand, so asking for some expert advice here. My questions: which version to install? I need windows client support so I need 1.5 - right? But it is not stable.. Or is it? And don't see any pre-built rpms for it, so compiling from sources? tried to compile and it worked but it created a non-"mp" kernel module while my kernel needs an mp one - how to workaround that? do I really need a new fresh partition to start with or I can re-use an existing one and just make it available via afp? any nice HOWTOs around?

  Read the article

• RTL8168B/8111B Lan card is not detected in Redhat..Error is make ***/lib/modules/2.6.18-53.e15/build

  - by Deepak Narwal

  0 Hello friends... In My computer Lan card model is Realtek RTL8168B/8111B PCI-E GIGABIT ETHERNET NIC (NDIS 6.20) My system is dual boot windows 7 and redhat 5.1.Redhat is not picking up this model of Lan card automaticlly. I tried it by downloading from realtak site for this particular model and find some .tar packages for my kernal and when i tried to install them ... check old drivers & unload it build the module and install make */lib/modules/2.6.18-53.e15/build: no such file or directory stop make[1]: *[modules] error 2 make : [modules] error 2 i downloaded tar files from sites and unpack according to their instrution i tried to run autorun.sh script as mentioned in readme file but after doing this it is showing above error... Now what to do i am not getting

  Read the article

• Problem upgrading kernel on debian 3.1

  - by exhuma

  Hi, I have a quite old box in a remote server farm. So I have no direct access. Only remote SSH (and via SSH to a serial console). I haven't updated this box in ages. Now, whenever I want to install a new package, a dependency to glibc appears. Unfortunately, the install of glibc depends on a 2.6 kernel and I am running a venerable 2.4 kernel (one more reason to upgrade). The problem is, that the install of a new kernel has an indirect (over locales) dependency to glibc. So, to install glibc, I need a new kernel. For a new kernel, I need to upgrade glibc. Essentially I am blocked. What's the best way to proceed considering I have no "hardware" access? Here's a quick transcript of the upgrade process: [green:~]% sudo aptitude install linux-image-686 Reading Package Lists... Done Building Dependency Tree Reading extended state information Initializing package states... Done Reading task descriptions... Done The following packages are unused and will be REMOVED: gcc-4.3-base The following NEW packages will be automatically installed: dash libc6-i686 libparse-recdescent-perl linux-image-2.6-686 linux-image-2.6.18-6-686 module-init-tools yaird The following packages have been kept back: adduser apache2 apache2-mpm-prefork apache2-utils apache2.2-common apt apt-utils aptitude autoconf autotools-dev awstats base-files base-passwd [...snip...] util-linux vacation vim vim-common wamerican wbritish wget whiptail whois wwwconfig-common zlib1g The following NEW packages will be installed: dash libc6-i686 libparse-recdescent-perl linux-image-2.6-686 linux-image-2.6.18-6-686 linux-image-686 module-init-tools yaird The following packages will be upgraded: hotplug libc6 2 packages upgraded, 8 newly installed, 1 to remove and 277 not upgraded. Need to get 0B/22.7MB of archives. After unpacking 52.1MB will be used. Do you want to continue? [Y/n/?] Writing extended state information... Done Preconfiguring packages ... (Reading database ... 34065 files and directories currently installed.) Preparing to replace libc6 2.3.6.ds1-13 (using .../libc6_2.7-18lenny2_i386.deb) ... Checking for services that may need to be restarted... Checking init scripts... WARNING: init script for postgresql not found. [ --- libc6 config screen appears here --- ] WARNING: POSIX threads library NPTL requires kernel version 2.6.8 or later. If you use a kernel 2.4, please upgrade it before installing glibc. The installation of a 2.6 kernel _could_ ask you to install a new libc first, this is NOT a bug, and should *NOT* be reported. In that case, please add etch sources to your /etc/apt/sources.list and run: apt-get install -t etch linux-image-2.6 Then reboot into this new kernel, and proceed with your upgrade dpkg: error processing /var/cache/apt/archives/libc6_2.7-18lenny2_i386.deb (--unpack): subprocess pre-installation script returned error exit status 1 Errors were encountered while processing: /var/cache/apt/archives/libc6_2.7-18lenny2_i386.deb E: Sub-process /usr/bin/dpkg returned an error code (1) Ack! Something bad happened while installing packages. Trying to recover: dpkg: dependency problems prevent configuration of locales: locales depends on glibc-2.7-1; however: Package glibc-2.7-1 is not installed. dpkg: error processing locales (--configure): dependency problems - leaving unconfigured Errors were encountered while processing: locales Reading Package Lists... Done Building Dependency Tree Reading extended state information Initializing package states... Done Reading task descriptions... Done Now, if I follow the instrunctions as promted I get the following. Note that I am using aptitude instead of apt-get to benefit from the better dependency tracking. I did try with apt-get first. But that let me to the same problem. [green:~]% sudo aptitude install -t etch linux-image-2.6.26-2-686 Reading Package Lists... Done Building Dependency Tree Reading extended state information Initializing package states... Done Reading task descriptions... Done E: Unable to correct problems, you have held broken packages. E: Unable to correct dependencies, some packages cannot be installed E: Unable to resolve some dependencies! Some packages had unmet dependencies. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following packages have unmet dependencies: linux-image-2.6.26-2-686: Depends: initramfs-tools (>= 0.55) but it is not installable or yaird (>= 0.0.13) but it is not installable or linux-initramfs-tool which is a virtual package. Any ideas?

  Read the article

• IIS7.5 Windows Authentication missing providers menu item (ntlm)

  - by Alex Bilbie

  I'm trying to enable NTLM authentication on a Windows Server 2008 R2 machine with IIS 7.5 for a specific file in my web root. I've been following these instructions http://docs.moodle.org/en/NTLM_authentication#IIS_Configuration In the IIS Manager I open the Authentication module, disable anonymous authentication and enable Windows Authentication however according to every post I can find on the matter I should have a 'providers' option appear but I don't. I've double checked in Server Manager that the 'Windows Authentication' security feature is enabled for IIS. Any help anyone can offer would be great, Thank you!

  Read the article

• meld on OS X 10.7 doesn't work?

  - by klm123

  I'm installing meld on Mac OS 10.7 using port. It has downloaded all dependencies and told that everything is ok: Staging meld into destroot Installing meld @1.5.3_0 Activating meld @1.5.3_0 Cleaning meld Updating database of binaries: 100.0% Scanning binaries for linking errors: 100.0% No broken files found. but when I run: [18:28:24]~$ meld Traceback (most recent call last): File "/opt/local/bin/meld", line 75, in <module> locale.setlocale(locale.LC_ALL,'') File "/opt/local/Library/Frameworks/Python.framework/Versions/2.7/lib/python2.7/locale.py", line 539, in setlocale return _setlocale(category, locale) locale.Error: unsupported locale setting what is the problem and how to deal with it?

  Read the article

• Problem with gmailfs

  - by user35529

  Hello(????????????) I've got a little with gmailfs. I'm trying to mount gmail accout as a local file system on my Debian Lenny using the following command. mount -t gmailfs none /mnt/gmail -o [email protected],password=mypassword,fsname=SixSixSix But it gives my garbage like this Ignored option :rw Traceback (most recent call last): File "/sbin/mount.gmailfs", line 166, in <module> main(mountpoint, namedOptions, useEncfs) File "/sbin/mount.gmailfs", line 92, in main gmailfs.main(mountpoint, namedOptions) File "/usr/lib/python2.5/site-packages/gmailfs.py", line 1175, in main server = Gmailfs(namedOptions,mountpoint,version="gmailfs 0.8.0",usage='',dash_s_do='setsingle') File "/usr/lib/python2.5/site-packages/gmailfs.py", line 611, in __init__ self.ga.login() File "/usr/lib/python2.5/site-packages/libgmail.py", line 316, in login raise GmailLoginFailure("Login failed. (Wrong username/password?)") libgmail.GmailLoginFailure: 'Login failed. (Wrong username/password?)' Username and Password are totally correct.

  Read the article

< Previous Page | 197 198 199 200 201 202 203 204 205 206 207 208  | Next Page >