Search Results

Search found 18781 results on 752 pages for 'ip port'.

Page 201/752 | < Previous Page | 197 198 199 200 201 202 203 204 205 206 207 208  | Next Page >

• Dedicated Server emails ending up in Junk

  - by Pasta

  I have a dedicated server that works fine. Recently I added a new domain with a new dedicated IP address. The emails from the webserver gets sent out from the primary IP address which is different from the IP address of the domain. This causes the emails to end up in the Junk email folders. Is there anything I can do changing the SMTP server to the new IP address or configuring send mail? I need this for my php server on centos.

  Read the article

• No Telnet login prompt when used over SSH tunnel

  - by SCO

  Hi there ! I have a device, let's call it d1, runnning a lightweight Linux. This device is NATed by my internet box/router, hence not reachable from the Internet. That device runs a telnet daemon on it, and only has root as user (no pwd). Its ip address is 192.168.0.126 on the private network. From the private network (let's say 192.168.0.x), I can do: telnet 192.168.0.126 Where 192.168.0.126 is the IP address in the private network. This works correctly. However, to allow administration, I'd need to access that device from outside of that private network. Hence, I created an SSH tunnel like this on d1 : ssh -R 4455:localhost:23 ussh@s1 s1 is a server somewhere in the private network (but this is for testing purposes only, it will endup somewhere in the Internet), running a standard Linux distro and on which I created a user called 'ussh'. s1 IP address is 192.168.0.48. When I 'telnet' with the following, let's say from c1, 192.168.0.19 : telnet -l root s1 4455 I get : Trying 192.168.0.48... Connected to 192.168.0.48. Escape character is '^]'. Connection closed by foreign host . The connection is closed after roughly 30 seconds, and I didn't log. I tried without the -l switch, without any success. I tried to 'telnet' with IP addresses instead of names to avoid reverse DNS issues (although I added to d1 /etc/hosts a line refering to s1 IP/name, just in case), no success. I tried on another port than 4455, no success. I gathered Wireshark logs from s1. I can see : s1 sends SSH data to c1, c1 ACK s1 performs an AAAA DNS request for c1, gets only the Authoritave nameservers. s1 performs an A DNS request, then gets c1's IP address s1 sends a SYN packet to c1, c1 replies with a RST/ACK s1 sends a SYN to c1, C1 RST/ACK (?) After 0.8 seconds, c1 sends a SYN to s1, s1 SYN/ACK and then c1 ACK s1 sends SSH content to d1, d1 sends an ACK back to s1 s1 retries AAAA and A DNS requests After 5 seconds, s1 retries a SYN to c1, once again it is RST/ACKed by c1. This is repeated 3 more times. The last five packets : d1 sends SSH content to s1, s1 sends ACK and FIN/ACK to c1, c1 replies with FIN/ACK, s1 sends ACK to c1. The connection seems to be closed by the telnet daemon after 22 seconds. AFAIK, there is no way to decode the SSH stream, so I'm really stuck here ... Any ideas ? Thank you !

  Read the article

• Can USB Hubs affect peripheral performance?

  - by Daniel Rasmussen

  Like many laptops, mine has 2 USB 2.0 ports. I'm looking to purchase a USB hub for my peripheral devices. I'm also planning on purchasing a laptop cooler with two USB powered fans, which connects to a USB port but can extend the plug, so it doesn't use one up. (Sorry for the poor description; see the link for a picture.) My questions are these: Can one plug 'too many' peripherals into a USB port? Can I plug my fans into a port, then the hub into the fans, then my keyboard and mouse, mic, and webcam into the extender..? Is it possible to draw too much power from a port? Secondly, will a USB hub affect the performance of any of my devices? I'm mostly worried about my mouse and keyboard. I like wired mice because I've noticed some lag in my Bluetooth mouse.

  Read the article

• ddclient to update namecheap subdomain?

  - by LF4

  I have a subdomain that I want to update with ddclient. I configured the ddclient to get the IP from dyndns but it's not updating the subdomain on namecheap. They said to use yourdomain.com as the login instead of my actual domain. Has anyone been able to get namecheap DNS updated with ddclient? I'm running CentOS 6.2 with ddclient 3.7.3. When I run ddclient I get the following. CONNECT: checkip.dyndns.org CONNECTED: using HTTP SENDING: GET / HTTP/1.0 SENDING: Host: checkip.dyndns.org SENDING: User-Agent: ddclient/3.7.3 SENDING: Connection: close SENDING: RECEIVE: HTTP/1.1 200 OK RECEIVE: Content-Type: text/html RECEIVE: Server: DynDNS-CheckIP/1.0 RECEIVE: Connection: close RECEIVE: Cache-Control: no-cache RECEIVE: Pragma: no-cache RECEIVE: Content-Length: 106 RECEIVE: RECEIVE: <html><head><title>Current IP Check</title></head><body>Current IP Address: IPADD</body></html> Use of uninitialized value in string ne at /usr/sbin/ddclient line 1998. WARNING: skipping update of lf4bot from <nothing> to IPADD WARNING: last updated <never> but last attempt on Fri Jun 15 22:46:21 2012 failed. WARNING: Wait at least 5 minutes between update attempts. ddclient.conf File daemon=300 # check every 300 seconds syslog=yes # log update msgs to syslog mail=root # mail all msgs to root mail-failure=root # mail failed update msgs to root pid=/var/run/ddclient.pid # record PID in file. ssl=yes # use ssl-support. Works with use=web, web=checkip.dyndns.org/, web-skip='IP Address' # found after IP Address protocol=namecheap \ server=dynamicdns.park-your-domain.com \ login=yourdomain.com \ password=PASSWORD \ lf4bot

  Read the article

• Possible DNS Injection and/or SSL hijack?

  - by Anthony

  So if I go to my site without indicating the protocol, I'm taken to: http://example.org/test.php But if I go directly to: https://example.org/test.php I get a 404 back. If I go to just: https://example.org I get a totally different site (a page about martial arts). I went to the site via https not very long ago (maybe a week?) and it was fine. This is a shared server, as I understand it, and I do not have shell access, so I'm limited to the site's CPanel to do any further investigations. But when I go to: example.org:2083 I'm taken to https://example.org:2083, which, if someone has taken over the SSL port, could mean they have taken over the 2083 part as well (at least in my paranoid mind). I'm made more nervous by the fact that the cpanel login page at the above address looks very new (better, really) compared to the last time I went to it over the weekend. It's possible that wires got crossed somewhere after a system update, but I don't want to put in my name username and password in case it's a phishing attempt. Is there any way to know for sure without shell access to know for sure if someone has taken over? If I look up the IP address for the host name, the IP address matches what I have on a phpinfo page I can get to over http. If I go to the IP address directly on port 2083, I get the same login mentioned above (new and and suspiciously nice). But the SSL cert shows as good when I go this route. So if that's the case (I know the IP is right, the cert checks out, and there isn't any DNS involved), is that enough to feel safe at that point of entry? Finally, if I can safely log in via the IP, does anyone have any advice on where to check first on CPanel for why the SSL port is forwarding to a site on karate? Thanks.

  Read the article

• Microsoft VirtualPC Networking Issue

  - by Joda Maki

  I am using Microsoft VPC running the supplied microsoft images to test IE6/7. The ip addresses that get assigned to these images are via dhcp and get valid ip addresses in my subnet. They can access the external internet just fine. However, they cannot ping my host machine, nor can my host machine ping them (using internal ip addresses). Thus, they can't access my webserver to test with. How is this possible and how do I fix it?

  Read the article

• How does Windows Remote Desktop Connection Work?

  - by Devoted

  How does Windows Remote Desktop connection work? An IP address is used to connect to the computer but....how can that IP be accessed from anywhere? If, for example, the IP address is 192.168.1.55, there MUST be another 192.168.1.55 somewhere else in the world. How does Remote Desktop know which one to connect to? Thanks so much

  Read the article

• Command-line connect to wired network for Ubuntu

  - by Tim

  I like to know how to use command-line to connect to a wired network in general for Ubuntu 8.10? In my case, I connect a cable to my laptop but it doesn't work with my WICD. So I like to try command-line method. Here is the ifconfig of my network adapters: $ ifconfig eth0 Link encap:Ethernet HWaddr 00:c0:9f:8d:23:74 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:19 Base address:0x1800 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4457 errors:0 dropped:0 overruns:0 frame:0 TX packets:4457 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:493002 (493.0 KB) TX bytes:493002 (493.0 KB) wlan0 Link encap:Ethernet HWaddr 00:0e:9b:ab:56:19 UP BROADCAST NOTRAILERS PROMISC ALLMULTI MTU:576 Metric:1 RX packets:1508929 errors:0 dropped:0 overruns:0 frame:0 TX packets:768144 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:806027375 (806.0 MB) TX bytes:78834873 (78.8 MB) wlan0:avahi Link encap:Ethernet HWaddr 00:0e:9b:ab:56:19 inet addr:169.254.5.92 Bcast:169.254.255.255 Mask:255.255.0.0 UP BROADCAST NOTRAILERS PROMISC ALLMULTI MTU:576 Metric:1 wmaster0 Link encap:UNSPEC HWaddr 00-0E-9B-AB-56-19-00-00-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Thanks and regards! UPDATE: Tried what oyvindio suggested. Here is the failing message: $ sudo dhclient3 eth0 There is already a pid file /var/run/dhclient.pid with pid 18279 killed old client process, removed PID file Internet Systems Consortium DHCP Client V3.1.1 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ mon0: unknown hardware address type 803 wmaster0: unknown hardware address type 801 mon0: unknown hardware address type 803 wmaster0: unknown hardware address type 801 Listening on LPF/eth0/00:c0:9f:8d:23:74 Sending on LPF/eth0/00:c0:9f:8d:23:74 Sending on Socket/fallback DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 5 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 10 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 12 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 15 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 11 DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8 No DHCPOFFERS received. No working leases in persistent database - sleeping.

  Read the article

• Using the Remote Desktops MMC snap-in how do you connect to nonstandard ports?

  - by NitroxDM

  I have some severs I manage VIA Remote Desktop. They do not listen on port 3389. I can connect with out issue doing IP:PORT. I now manage so many I'm trying to use the Remote Desktop snap-in for the management console. But it will not let you enter a colon in the host name. Is there another way to specify the port? Here is link to the snap-in.

  Read the article

• PSAD Firewall/ UDP flood?

  - by Asad Moeen

  Well I'm actually trying to block a UDP Flood on the Application port because the string "getstatus" is causing my application to make large output due to a small input to the attacker's IP. I installed PSAD firewall to do the job. psad -S shows 3000,000 logged packets at the application port and top ports in Scan but does not block the IP of the attacker however other IP Addresses with small number of connections are dropped. I'm thinking that since output is also being made to the attacker, this is why its not getting blocked because iptables rate-limiting is also exactly doing the same thing and not blocking the IP where outgoing connection is also made. Any guesses why it won't work?

  Read the article

• Large concurrent user performance issues for Apache + mod_jk + GlassFish v3.1 clusters

  - by user10035

  I am running a java ee 6 ear application on a GlassFish v3.1 ( 2 clusters with 2 instances each) load balanced by an Apache v2.2 with mod_jk - all on the same server (Windows Server 2003 R2, Intel Xeon CPU x5670 @2.93Ghz, 6GB RAM, 2 cpus). The web application is accessed by around ~100 users. When they all try to access it at the same time every morning ~8am, the response is very slow while trying to access the main jsf home page. Apart from that I have seen the CPU usage spike upto 99% by the httpd process during the day frequently and I start seeing errors in the mod_jk.log file. [Wed Jun 08 08:25:43 2011] [9380:8216] [info] ajp_process_callback::jk_ajp_common.c (1885): Writing to client aborted or client network problems [Wed Jun 08 08:25:43 2011] [9380:8216] [info] ajp_service::jk_ajp_common.c (2543): (myAppLocalInstance4) sending request to tomcat failed (unrecoverable), because of client write error (attempt=1) Any suggestions on how I can go about improving this? Apache configuration is mostly the default as shown below ServerRoot "C:/Program Files/Apache Software Foundation/Apache2.2" Listen 80 LoadModule actions_module modules/mod_actions.so LoadModule alias_module modules/mod_alias.so LoadModule asis_module modules/mod_asis.so LoadModule auth_basic_module modules/mod_auth_basic.so LoadModule authn_default_module modules/mod_authn_default.so LoadModule authn_file_module modules/mod_authn_file.so LoadModule authz_default_module modules/mod_authz_default.so LoadModule authz_groupfile_module modules/mod_authz_groupfile.so LoadModule authz_host_module modules/mod_authz_host.so LoadModule authz_user_module modules/mod_authz_user.so LoadModule autoindex_module modules/mod_autoindex.so LoadModule cgi_module modules/mod_cgi.so LoadModule dir_module modules/mod_dir.so LoadModule env_module modules/mod_env.so LoadModule include_module modules/mod_include.so LoadModule isapi_module modules/mod_isapi.so LoadModule log_config_module modules/mod_log_config.so LoadModule mime_module modules/mod_mime.so LoadModule negotiation_module modules/mod_negotiation.so LoadModule setenvif_module modules/mod_setenvif.so <IfModule !mpm_netware_module> <IfModule !mpm_winnt_module> User daemon Group daemon </IfModule> </IfModule> DocumentRoot "C:/Program Files/Apache Software Foundation/Apache2.2/htdocs" <Directory /> Options FollowSymLinks AllowOverride None Order deny,allow Deny from all </Directory> <Directory "C:/Program Files/Apache Software Foundation/Apache2.2/htdocs"> Options Indexes FollowSymLinks AllowOverride None Order allow,deny Allow from all </Directory> <IfModule dir_module> DirectoryIndex index.html </IfModule> <FilesMatch "^\.ht"> Order allow,deny Deny from all Satisfy All </FilesMatch> ErrorLog "logs/error.log" LogLevel warn <IfModule log_config_module> LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %b" common <IfModule logio_module> LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\" %I %O" combinedio </IfModule> CustomLog "logs/access.log" common </IfModule> <IfModule alias_module> ScriptAlias /cgi-bin/ "C:/Program Files/Apache Software Foundation/Apache2.2/cgi-bin/" </IfModule> <Directory "C:/Program Files/Apache Software Foundation/Apache2.2/cgi-bin"> AllowOverride None Options None Order allow,deny Allow from all </Directory> DefaultType text/plain <IfModule mime_module> TypesConfig conf/mime.types AddType application/x-compress .Z AddType application/x-gzip .gz .tgz </IfModule> Include conf/extra/httpd-mpm.conf <IfModule ssl_module> SSLRandomSeed startup builtin SSLRandomSeed connect builtin </IfModule> LoadModule jk_module modules/mod_jk.so JkWorkersFile conf/workers.properties JkLogFile logs/mod_jk.log JkLogLevel info JkLogStampFormat "[%a %b %d %H:%M:%S %Y] " JkOptions +ForwardKeySize +ForwardURICompat -ForwardDirectories JkRequestLogFormat "%w %V %T" JkMount /myApp/* loadbalancerLocal JkMount /myAppRemote/* loadbalancerRemote JkMount /myApp loadbalancerLocal JkMount /myAppRemote loadbalancerRemote The workers.properties config file is: worker.list=loadbalancerLocal,loadbalancerRemote worker.myAppLocalInstance1.type=ajp13 worker.myAppLocalInstance1.host=localhost worker.myAppLocalInstance1.port=8109 worker.myAppLocalInstance1.lbfactor=1 worker.myAppLocalInstance1.socket_keepalive=1 worker.myAppLocalInstance1.socket_timeout=1000 worker.myAppLocalInstance2.type=ajp13 worker.myAppLocalInstance2.host=localhost worker.myAppLocalInstance2.port=8209 worker.myAppLocalInstance2.lbfactor=1 worker.myAppLocalInstance2.socket_keepalive=1 worker.myAppLocalInstance2.socket_timeout=1000 worker.myAppLocalInstance3.type=ajp13 worker.myAppLocalInstance3.host=localhost worker.myAppLocalInstance3.port=8309 worker.myAppLocalInstance3.lbfactor=1 worker.myAppLocalInstance3.socket_keepalive=1 worker.myAppLocalInstance3.socket_timeout=1000 worker.myAppLocalInstance4.type=ajp13 worker.myAppLocalInstance4.host=localhost worker.myAppLocalInstance4.port=8409 worker.myAppLocalInstance4.lbfactor=1 worker.myAppLocalInstance4.socket_keepalive=1 worker.myAppLocalInstance4.socket_timeout=1000 worker.myAppRemoteInstance1.type=ajp13 worker.myAppRemoteInstance1.host=localhost worker.myAppRemoteInstance1.port=8509 worker.myAppRemoteInstance1.lbfactor=1 worker.myAppRemoteInstance1.socket_keepalive=1 worker.myAppRemoteInstance1.socket_timeout=1000 worker.myAppRemoteInstance2.type=ajp13 worker.myAppRemoteInstance2.host=localhost worker.myAppRemoteInstance2.port=8609 worker.myAppRemoteInstance2.lbfactor=1 worker.myAppRemoteInstance2.socket_keepalive=1 worker.myAppRemoteInstance2.socket_timeout=1000 worker.myAppRemoteInstance3.type=ajp13 worker.myAppRemoteInstance3.host=localhost worker.myAppRemoteInstance3.port=8709 worker.myAppRemoteInstance3.lbfactor=1 worker.myAppRemoteInstance3.socket_keepalive=1 worker.myAppRemoteInstance3.socket_timeout=1000 worker.myAppRemoteInstance4.type=ajp13 worker.myAppRemoteInstance4.host=localhost worker.myAppRemoteInstance4.port=8809 worker.myAppRemoteInstance4.lbfactor=1 worker.myAppRemoteInstance4.socket_keepalive=1 worker.myAppRemoteInstance4.socket_timeout=1000 worker.loadbalancerLocal.type=lb worker.loadbalancerLocal.sticky_session=True worker.loadbalancerLocal.balance_workers=myAppLocalInstance1,myAppLocalInstance2,myAppLocalInstance3,myAppLocalInstance4 worker.loadbalancerRemote.type=lb worker.loadbalancerRemote.balance_workers=myAppRemoteInstance1,myAppRemoteInstance2,myAppRemoteInstance3,myAppRemoteInstance4 worker.loadbalancerRemote.sticky_session=True

  Read the article

• How to configure networking on an appliance such that it can plug and play on any corporate network?

  - by Joshua Lim

  I had a chance to configure a Moxa NPort device server appliance on my client's network, it was very easy to do so, done in just 2 minutes. Here's what I did:- The Moxa device server had a preset IP address of 192.168.127.254 and subnet mask 255.255.255.0 - http://www.moxa.com/doc/manual/nport/5400/NPort_5400_Series_Users_Manual_v4.pdf Moxa provides a Windows software which I used to "scan" for the device server. It worked like magic! The software returns a list of device servers found. Each device server is identified by MAC address, and by selecting the device server using the software, I can reset the default IP address and subnet mask of that device server! In comparison, during an earlier project, I spent 2 hours trying to get KVM to work for a Windows 7 embedded appliance I'm trying to install in my client's network - http://superuser.com/questions/380305/how-to-configure-windows-7-professional-appliance-pc-on-my-clients-network-usin Prior to that, I have already tried pre-configuring the IP address and subnet mask to the one which my client provided, yet the appliance still can't connect to the client's network! I've also tried cross cable, didn't work either. After KVM worked, I discovered that the network settings were "lost" after I plug the machine into the client's network. Now my question is what can I do to setup my Windows 7 embedded appliance so that it can connect to any network like that the Moxa device server? I tried experimenting this on my network using a Windows machine configured to an IP address of 192.168.127.254 and subnet mask 255.255.255.0, but it doesn't connect to my network that uses 192.168.0.*. :( EDIT: I would like to point out that the Moxa Windows configuration software seems to be able to connect to any Moxa device connected to the network even if it is on a different subnet, as long as the network adapter shows "connected". This is important because the Moxa device has no VGSM port or interface to configure the IP address.

  Read the article

• Can't bring NAT to work

  - by user31738

  Hello, I bought a D-link DIR-300 wireless router and i can't bring NAT to work, i have an ssh and http service i need to forward to the internet. My connection is as follows: I have an ADSL connection, i'm using a ADSL ethernet modem connected and working, it doesnt let me put it on bridge mode. I have my router connected to my adsl modem through ethernet, it gets its ip through DHCP (and i'ts always the same) I have a desktop computer running linux with apache and openssh configured and working, it has fixed ip. I configured the NAT in the modem forwarding port 22 from the router ip to the internet. In the router i setup NAT forwarding port 22 from the desktop computer fixed ip to out there. This setup already worked with a fonera i had before, can anyone help me with this or tell me what kind of tests do i need to do? How can i test if the router is forwarding ports correctly before the modem?

  Read the article

• Multiple WAN interfaces on SonicWall TZ 100?

  - by Chad Decker

  I'm using a SonicWall TZ 100 with a basic configuration of X0 for the LAN and X1 for the WAN. The WAN uses DHCP to obtain its routable IP address. I want to obtain a second routable IP from my ISP. I'm in luck because my cable company will provide me with an additional dynamic IP for $5/mo. How do I bind this IP to my SonicWall? My additional dynamic IP will not be consecutive to the original one. It won't even be on the same class C. I think what I want to do is to use one of the empty ports/interfaces (X2, X3, or X4), tell that interface to use DHCP, and then add that interface to the WAN "zone". I can't figure out how to do this though. Here's what I've tried so far: (1) I've looked in Network Interfaces. I see X0 and X1 but the other unused interfaces don't show up. I don't see an "Add" button to add the new interfaces. (2) I've looked in Network Zones. I see that X0, X2, X3, X4 are in the LAN zone. I tried to drag X3 into the WAN zone but I can't. Nor does clicking the "Configure" button allow me to move an unused interface from LAN to WAN. (3) I've read the post entitled Splitting up multiple WAN's on Sonicwall. This doesn't seem applicable to me. Any thoughts?

  Read the article

• Set postfix to send email but not to receive them

  - by CodeShining

  I'm using Google Apps to handle personal email addresses for my domain name, and I set up the DNS as Google suggests. All works fine. Now since I need a SMTP to send emails from my e-commerce I installed Postfix on the server. It works fine when I send emails to any email address but it doesn't send to the same domain name, so let's say my domain is example.com, I set postfix using example.com, if I try to reset a password using [email protected] postfix doesn't send and instead reports on the mail.log Sep 20 01:09:52 ip-10-54-26-162 postfix/pickup[6809]: B09A3415D8: uid=33 from=<www-data> Sep 20 01:09:52 ip-10-54-26-162 postfix/cleanup[6854]: B09A3415D8: message-id=<20120920010952.B09A3415D8@ip-10-54-26-162.eu-west-1.compute.internal> Sep 20 01:09:52 ip-10-54-26-162 postfix/qmgr[30978]: B09A3415D8: from=<[email protected]>, size=4234, nrcpt=1 (queue active) Sep 20 01:09:52 ip-10-54-26-162 postfix/local[6856]: B09A3415D8: to=<[email protected]>, relay=local, delay=0.01, delays=0.01/0/0/0, dsn=5.1.1, status=bounced (unknown user: "myaccount") Of course it cannot find a local user "myaccount" since that account is on Google Apps... How can I tell Postfix to send the email and do not search for a local user?

  Read the article

• Transparent proxying leaves sockets with SYN_RCVD in MacOS X 10.6 Snow Leopard (and maybe FreeBSD)

  - by apenwarr

  I'm trying to create a transparent proxy on my MacOS machine in order to port the sshuttle ssh-based transproxy VPN from Linux. I think I almost have it working, but sadly, almost is not 100%. Short version is this. In one window, start something that listens on port 12300: $ while :; do nc -l 12300; done Now enable proxying: # sysctl -w net.inet.ip.forwarding=1 # sysctl -w net.inet.ip.fw.enable=1 # ipfw add 1000 fwd 127.0.0.1,12300 log tcp from any to any And now test it out: $ telnet localhost 9999 # any port number will do # this works; type stuff and you'll see it in the nc window $ telnet google.com 80 # any host/port will do # this *doesn't* work! After the latter experiment, I see lines like this in netstat: $ netstat -tn | grep ^tcp4 tcp4 0 0 66.249.91.104.80 192.168.1.130.61072 SYN_RCVD tcp4 0 0 192.168.1.130.61072 66.249.91.104.80 SYN_SENT The second socket belongs to my telnet program; the first is more suspicious. SYN_RCVD implies that my SYN packet was correctly captured by the firewall and taken in by the kernel, but apparently the SYNACK was never sent back to telnet, because it's still in SYN_SENT. On the other hand, if I kill the nc server, I get this: $ telnet google.com 80 Trying 66.249.81.104... telnet: connect to address 66.249.81.104: Connection refused telnet: Unable to connect to remote host ...which is as expected: my proxy server isn't running, so ipfw redirects my connection to port 12300, which has nobody listening on it, ie. connection refused. My uname says this: $ uname -a Darwin mean.local 10.2.0 Darwin Kernel Version 10.2.0: Tue Nov 3 10:37:10 PST 2009; root:xnu-1486.2.11~1/RELEASE_I386 i386 Does anybody see any different results? (I'm especially interested in Snow Leopard vs Leopard results, as there seem to be some internet rumours that transproxy is broken in Snow Leopard version) Any advice for how to fix?

  Read the article

• Nginx > Varnish > Gunicorn Error Too many Redirections

  - by kollo

  I have the following config: Nginx Varnish Gunicorn Django I want to cache 2 versions of same site (mobile & web) with Varnish. Gunicorn : WEB: gunicorn_django --bind 127.0.0.1:8181 MOBILE: gunicorn_django --bind 127.0.0.1:8182 Nginx: WEB: server { listen 80; server_name www.mysite.com; location / { proxy_pass http://127.0.0.1:8282; # pass to Varnish proxy_set_header X-Real-IP $remote_addr; proxy_set_header Host $host; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; } } MOBILE: server { listen 80; server_name m.mysite.com; location / { proxy_pass http://127.0.0.1:8282; # pass to Varnish proxy_set_header X-Real-IP $remote_addr; proxy_set_header Host $host; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; } } Varnish: default.vcl backend mobile_mysite { .host = "127.0.0.1"; .port = "8182"; } backend mysite { .host = "127.0.0.1"; .port = "8181"; } sub vcl_recv { if (req.http.host ~ "(?i)^(m.)?mysite.com$") { set req.http.host = "m.mysite.com"; set req.backend = mobile_mysite; }elsif (req.http.host ~ "(?i)^(www.)?mysite.com$") { set req.http.host = "mysite.com"; set req.backend = mysite; } if (req.url ~ ".*/static") { /* do not cache static content */ return (pass); } } The problem: On Nginx if I setup Mobile version with Varnish (port 8282) and let WEB version with Gunicorn( port 8181), MOBILE is cached by varnish, both WEB & MOBILE works but WEB is not cached. If I set the proxy_pass of WEB version to Varnish (port 8282) and restart Nginx I got an error when accessing web version (www.mysite.com) "Too many redirections" . I Think my problem come from the Varnish config file, as the site works well if I setup Nginx proxy_pass to Gunicorn ports (MOBILE & WEB).

  Read the article

• Networking 2 Virtual PC with one VPC as DHCP server

  - by vivek

  My host OS is Win XP Professional. The host has a real network connection via DSL and I created a second network connection using Microsoft Loopback Adapter. Internet connection sharing is enabled. The Microsoft Loopback adapter has a IP address of 192.168.0.1. I have 1 Virtual PC which has Windows Server 2003. I have setup the network connection on this VPC to use Microsoft Loopback Adapter. I setup this VPC to be the Domain Controller , DNS Server and DHCP Server. I set this to a static IP address 192.168.0.2 (on the same subnet as the MS Loopback adapter) I have a second Virtual PC which also has Windows Server 2003. The network connection on this VPC is set to "Local Only". I want this VPC to get its IP address from the 1st VPC on which I setup as a DHCP server. What i want is the 2 VPC should be in a network with one of the VPC acting as the domain controller, DNS Server and DHCP server. The second VPC shoud get its IP address from the 1st VPC. It should be a part of the domain of the 1st VPC. When i tried to make the second VPC get the IP address from the first VPC I am not succeeding. Can somebody post some suggestions on how to go about this ?

  Read the article

• FreeBSD jail with IPFW with loopback - unable to connect loopback interface

  - by khinester

  I am trying to configure a one IP jail with loopback interface, but I am unsure how to configure the IPFW rules to allow traffic to pass between the jail and the network card on the server. I have followed http://blog.burghardt.pl/2009/01/multiple-freebsd-jails-sharing-one-ip-address/ and https://forums.freebsd.org/viewtopic.php?&t=30063 but without success, here is what i have in my ipfw.rules # vim /usr/local/etc/ipfw.rules ext_if="igb0" jail_if="lo666" IP_PUB="192.168.0.2" IP_JAIL_WWW="10.6.6.6" NET_JAIL="10.6.6.0/24" IPF="ipfw -q add" ipfw -q -f flush #loopback $IPF 10 allow all from any to any via lo0 $IPF 20 deny all from any to 127.0.0.0/8 $IPF 30 deny all from 127.0.0.0/8 to any $IPF 40 deny tcp from any to any frag # statefull $IPF 50 check-state $IPF 60 allow tcp from any to any established $IPF 70 allow all from any to any out keep-state $IPF 80 allow icmp from any to any # open port ftp (20,21), ssh (22), mail (25) # ssh (22), , dns (53) etc $IPF 120 allow tcp from any to any 21 out $IPF 130 allow tcp from any to any 22 in $IPF 140 allow tcp from any to any 22 out $IPF 150 allow tcp from any to any 25 in $IPF 160 allow tcp from any to any 25 out $IPF 170 allow udp from any to any 53 in $IPF 175 allow tcp from any to any 53 in $IPF 180 allow udp from any to any 53 out $IPF 185 allow tcp from any to any 53 out # HTTP $IPF 300 skipto 63000 tcp from any to me http,https setup keep-state $IPF 300 skipto 63000 tcp from any to me http,https setup keep-state # deny and log everything $IPF 500 deny log all from any to any # NAT $IPF 63000 divert natd ip from any to any via $jail_if out $IPF 63000 divert natd ip from any to any via $jail_if in but when i create a jail as: # ezjail-admin create -f continental -c zfs node 10.6.6.7 /usr/jails/node/. /usr/jails/node/./etc /usr/jails/node/./etc/resolv.conf /usr/jails/node/./etc/ezjail.flavour.continental /usr/jails/node/./etc/rc.d /usr/jails/node/./etc/rc.conf 4 blocks find: /usr/jails/node/pkg/: No such file or directory Warning: IP 10.6.6.7 not configured on a local interface. Warning: Some services already seem to be listening on all IP, (including 10.6.6.7) This may cause some confusion, here they are: root syslogd 1203 6 udp6 *:514 *:* root syslogd 1203 7 udp4 *:514 *:* i get these warning and then when i go into the jail environment, i am unable to install any ports. any advice much appreciated.

  Read the article

• Not all of your nameservers are in different subnets. Single point of failure

  - by user2118559

  Using VPS hosting and dynadot (domain registrar) DNS. Checked domain name with http://www.intodns.com and get some warnings Different subnets WARNING: Not all of your nameservers are in different subnets and Different autonomous systems WARNING: Single point of failure As understand to avoid the warning must have second Ip4 address and both the addresses must point to different servers? If both Ip addresses point to the same server, it does not help? I mean each server has own Ip address. If one server down, then visitors can access website (files) on another server? Is this the reason why need more than one Ip? Tried to point website to 2 ip addresses and after some time get warning from uptimerobot Connection Timeout

  Read the article

• Bypassing SQUID on freebsd with PF

  - by epema

  I have PF+SQUID31 on FREEBSD-9.0, and I want to have some hosts(aka goodguys) to bypass the proxy, so that torrents are not logged. Also, I am not sure about transparent. It means that I dont have to configure proxy settings on the client side right? I have tried doing a redirect no rdr on $int_if inet proto {tcp,udp} from 192.168.1.233/32 to any However, no luck :( Here is a quick look of my conf files: SQUID /usr/local/etc/squid/squid.conf http_port 192.168.1.1:8080 transparent RC /etc/rc.conf: gateway_enable="YES" pf_enable="YES" pf_rules="/usr/local/etc/pf.conf" pflog_enable="YES" squid_enable="YES" I have squid31 installed from ports with SQUID_PF "Enable transparent proxying with PF" on PF /usr/loca/etc/pf.conf: int_if="re0" ext_if="bge0" localnet="{ 192.168.1.0/24 }" table <goodguys> const { "192.168.1.219", "192.168.1.233" } set block-policy drop set skip on lo0 scrub in all fragment reassemble scrub out all random-id max-mss 1440 block in on $ext_if pass out on $ext_if keep state block in on $int_if pass in on $int_if inet proto tcp from $int_if:network to $int_if port 8080 keep state pass in on $int_if inet proto udp from $int_if:network to $int_if port 21 keep state pass in on $int_if inet proto udp from $int_if:network to $int_if port 22 keep state pass in on $int_if inet proto udp from $int_if:network to $int_if port 53 keep state pass in on $int_if inet proto tcp from $int_if:network to any port { smtp, pop3 } keep state pass in on $int_if inet proto icmp from $int_if:network to $int_if keep state pass out on $int_if keep state What lines should I add in conf files? I am assuming that the problem is on the firewall(pf).

  Read the article

• Ubuntu Pound Reverse Proxy Load Balancing Based off active server load?

  - by Andrew

  I have Pound installed on a loadbalancer. It seems to work okay, except that it randomly assigns the backend server to forward the request to. I've put 1 backend machine under so much load that it went into using swap, and I can't even ssh into it to test this scenareo. I would like the loadbalancer to realize that the machine is overloaded, and send it to a different backend machine. However it doesn't. I've read the man page and it seems like the directive "DynScale 1" is what would monitor this, but it still redirects to the overloaded server. I've also put in "HAport 22" to the backend figuring since I can't ssh in, neither could the loadbalancer and it would consider the backend server dead until it gets rid of the load and responds, but that didn't help either. If anyone could help with this, I'd appreciate it. My current config is below. ###################################################################### ## global options: User "www-data" Group "www-data" #RootJail "/chroot/pound" ## Logging: (goes to syslog by default) ## 0 no logging ## 1 normal ## 2 extended ## 3 Apache-style (common log format) LogLevel 3 ## check backend every X secs: Alive 5 DynScale 1 Client 1200 TimeOut 1500 # poundctl control socket Control "/var/run/pound/poundctl.socket" ###################################################################### ## listen, redirect and ... to: ## redirect all requests on port 80 to SSL ListenHTTP Address 192.168.1.XX Port 80 Service Redirect "https://xxx.com/" End End ListenHTTPS Address 192.168.1.XX Port 443 Cert "/files/www.xxx.com.pem" Service BackEnd Address 192.168.1.1 Port 80 HAport 22 End BackEnd Address 192.168.1.2 Port 80 HAport 22 End End End

  Read the article

• Routing RFC1918 addresses through dd-wrt via a switch

  - by espenfjo

  I am a bit stuck with an experiment of mine. I have a network looking somewhat like this. | Internet | | ---- |Switch| ---- | | Server w/pub IP | DD-WRT router 192.168.1.1 | | RFC1918 clients 192.168.1.0/24 What I want is for the RFC1918 clients to speak directly with each others. On the server with the public IP I have this route: 192.168.1.0/24 dev eth0 scope link and can see that packets are infact reaching the dd-wrt router for 192.168.1.1, even though if I get no answer. Trying to reach one of the RFC1918 clients from the public IP server will get no result, as the dd-wrt router is not announcing that network on to its external interface (arp who-has 192.168.1.107 tell xxx.xxx.xxx.xxx, but no answer). The router being an WLAN dd-wrt router has of course a load of routes, VLANs and interfaces: xxx.xxx.xxx.1 dev vlan2 scope link 192.168.1.0/24 dev br0 proto kernel scope link src 192.168.1.1 192.168.1.0/24 dev eth1 proto kernel scope link src 192.168.1.244 84.215.64.0/18 dev vlan2 proto kernel scope link src xxx.xxx.xxx.xxx 169.254.0.0/16 dev br0 proto kernel scope link src 169.254.255.1 127.0.0.0/8 dev lo scope link 0.0.0.0 via xxx.xxx.xxx.1 dev vlan2 xxx.xxx.xxx.xxx being the public IP, and xxx.xxx.xxx.1 being the default route for the public IP. I am not sure where to continue with this. I would recon that I both need routing on the dd-wrt router, as well as some iptables magic? Why do something this complex? Why not ;) Also, do not mind that "Internet" can get RFC1918 traffic, it wont go outside of the walls. EDIT 1: Following the tip from stew I do indeed get the correct ARP flowing. And adding an iptables rule for allowing traffic from that specific public IPd machine I get traffic between the systems! Oddly enough though, the speed I get from Server w/pub IP - RFC1918 clients are the same as if the traffic were routed out onto the Internet and back. Edit 2: Ok, disconnecting the external Internet connection will still give the same, crappy transfer speed. So it has to be something else. Edit 3: Ok, I guess there are other reasons for this crappy speed. Case closed. :)

  Read the article

• How to send connection type (SSH|Telnet) info in Radius Access Requests on Cisco router?

  - by Gianni Costanzi

  I've configured the following on a cisco router: aaa authentication login default group radius local ! radius-server host x.x.x.x auth-port 1012 acct-port 1013 radius-server host y.y.y.y auth-port 1012 acct-port 1013 radius-server retransmit 1 radius-server timeout 3 radius-server key 7 xxxxxxxxx I'd like to be able to specify some radius options in order to add information about the type of connection for which a user is being authenticated, i.e. I'd like the radius server to receive in the Cisco Router's Radius Access Request information about the connection being SSH or Telnet.. I'd like to find something that automatically adds this info in the access request, without specific configurations on VTY lines dedicated to SSH and to Telnet. Any idea about that?

  Read the article

• Cluster Core Resource state of Exchange 2010 DAG

  - by Christoph

  I have two Exchange 2010 servers in a DAG and a witness server to implement mailbox resiliency. The two Exchange servers are in two subnets and the Windows failover cluster therefore has two IP address resources. I now that Exchange uses "core functionality" of Windows Server failover clustering, but it does not use all features. My setup also seems to work, but if I run the validation in the Windows Failover Cluster Manager, it complains about one of the IP address resources being offline. However, I cannot bring this resource online, because the server complains that "the specified cluster node is not the owner of the resource, or the node is not a possible owner of the resource". If I "Simulate failure of this resource", it becomes offline and the other IP becomes online. I have the vague idea that Exchange might use the state of the IP resource to identify the Primary Active Manager, but I am not sure. As it is obviously important that failover really works, I would like to be sure. Therefore, my question is: Is it normal that only one IP address resource in a Exchange 2010 DAG failover cluster is active at a time? If not, how do I bring both resources online at the same time given the error described above?

  Read the article

< Previous Page | 197 198 199 200 201 202 203 204 205 206 207 208  | Next Page >