Search Results

Search found 25447 results on 1018 pages for 'chester is back'.

Page 202/1018 | < Previous Page | 198 199 200 201 202 203 204 205 206 207 208 209  | Next Page >

• Windows 8 keeps signing out

  - by bill weaver

  Ran into a strange problem with Windows 8 Pro. Last night i installed Windows 8 Pro as an upgrade on a Sony Vaio laptop that had Windows 7 Pro on it. The install seemed to go okay. Then once installed, live tiles seem to work, native/Metro apps will start okay, but pretty soon after going into an app or settings, the screen flashes a few times and we're back to the lock screen. Signing in appears to do a full login. I've tried this with a local account and with a live.com account. This is someone else's laptop, so we decided to let it breathe, in case the install was still settling in. Well, they say today it's doing the same thing. Open the music app, and within a minute it's back to signon/lock screen. However, they can go to the actual Desktop and run Zune to play music, and it seems happy. In the past, i've installed retail Windows 8 Pro clean on a homebrew system, as an upgrade on a Dell laptop with a zillion apps and drivers, neither with any problems. Also, i've had the consumer preview and release candidate installed as well, no problems. Any ideas on what's going on here?

  Read the article

• iSCSI performance questions

  - by RyanLambert

  Hi everyone, apologies for the long-winded post in advance... Attempting to troubleshoot some iSCSI sluggishness on a brand new vSphere deployment (still in test). Layout is as such: 3 VSphere hosts, each with 2x 10GB NICs plugged into a pair of Nexus 5020s with a 10gig back-to-back between them. NICs are port-channeled in an active/active redundant fashion (using vPC-mac pinning for those of you familiar with N1KV) Both NICs carry service console, vmotion, iSCSI, and guest traffic. iSCSI is on a single subnet/single VLAN that is not routed through our IP network (strictly layer2) Had this been a 1gig deployment, we probably would have split the iSCSI traffic off onto separate NICs, but the price/port gets rather ridiculous when you start throwing 4+ NICs to a server in a 10gigabit infrastructure, and I'm not really convinced it's necessary. Open to dialogue/tech facts re: this, though. At this point even a single VM guest will boot slowly to iSCSI storage (EMC CX4 on the same Nexus 5020 10gig switches), and restores of VMs from iSCSI take about twice as long as we'd expect them to. Our server folks mentioned that if we split the iSCSI off onto its own NIC, performance seems significantly better. From a network perspective, I've run through the variables I can think of (port configuration errors, MTU problems, congestion etc.) and I'm coming up dry. There really is no other traffic on these hosts other than the very specific test being performed at the time. Important thing to note is that guest traffic works just fine... it seems storage is the only thing affected by whatever gremlin exists. Concluding that we're not 'overutilizing' the network infrastructure since we're doing hardly anything, I'm just looking for some helpful tips/ideas we can use to resolve this... preferably without hurling extra 10gig NICs that are going to sit around 10% utilization while we've got 70+% left on our others.

  Read the article

• E-mail duplication problem

  - by Gavin Osborn

  I have taken out a hosting agreement with a well respected hosting provider for a couple of internet facing servers. We have deployed several applications to these servers which send various e-mails back to us for reporting purposes. Context: Each server runs Windows Server 2003 R2 with the IIS 6.0 SMTP service installed. Each application is configured to use the local instance of IIS to send e-mails. The external IP address of each server is mapped to a particular domain eg: server1.mydomain.com server2.mydomain.com These e-mails are sent from a company domain name and not the domain name of the hosted servers (eg: [email protected]) Symptoms: A small number (<1%) of e-mails sent from these applications appear to be duplicated. These are exact duplicate in terms of both content and message headers. The Fix: I contacted my hosting provider and they told me this was a common problem & instructed me to: Change the HELO response of your mail server service to a FQDN (server1.mydomain.com && server2.mydomain.com) Create a DNS A record that resolves the FQDN of your mail server to the primary IP address of your sending mail server. Create a PTR record that resolves your primary IP address back to your mail server's FQDN In the sending domain's (mycompanydomain.com) DNS zone file, add the appropriate SPF record for your hosted servers. eg: v=spf1 a mx include:mydomain -all The Problem Continues: I made all of the changes as prescribed above, I was a little hesitant because these steps seemed to suggest they were more for stopping your messages getting blocked than they were for stopping them from being duplicated - but I am certainly no expert in these matters. It has been 5 days since I applied this fix and the problem still persists. I am certain that these problems are not a bug in the software because they are 4 different applications installed on 2 different servers, all of whom are exhibiting this strange behaviour. This behaviour has also not been seen in our UAT environment. Were my hosts correct to suggest this fix? If not, does anyone know what could be the cause of this problem? Many Thanks

  Read the article

• Issues using gmail with google apps and external domain

  - by Jonathan Kelly

  I have recently tried to use gmail through google apps as my main email client, but I'm experiencing a few different problems. I am managing the domain (conjunktiondesign.co.uk) through 123reg.co.uk but it is hosted through fasthosts.co.uk. I transfered the domain to 123reg as fasthosts did not allow me to change the MX records myself. I followed the setup instructions step by step on google apps and changed the MX records as they told me to. My email was now working perfectly but my website was down and I was getting the following error: The dnsserver returned: No DNS records I have a friend that is using the same system as me (ie. Externally hosted domain and google apps mail) and I changed my 123reg details to the same that he had (as his was working perfectly - both email and website). I changed my name servers to point to fasthosts, rather than 123reg and I added an A record called '@' pointing to fasthosts IP address. I also created another A record called 'www' pointing to fasthosts IP address. After I did this, my website worked almost immediately but I have only realised that since changing it my email is now down. I have not received anything since Saturday. I am a web designer and would consider myself fairly tech savvy, but I have no idea about A records, CNAME's and all the things I have been messing about with! What I ultimately need is someone to help me get my email and website working at the same time, rather than one being down when the other is OK. I seem only able to get one or the other working. I have now changed the name servers back to 123reg in an attempt to get my email back as it is more important than my website at this stage. Any help is much appreciated. Thanks.

  Read the article

• Western Digital My Book not recognized by WD software

  - by Kari

  A few years ago I bought a WD My Book Pro 2. It worked fine for a while, then one of the drives failed and I sent it back to be replaced under warranty. I never got around to setting up the new one when I got it back. I finally ran out of room on my internal drive, so I tried to use the external - no go. Both drives spin up, but aren't recognized by either Disk Utility (Mac) or the WD Drive Manager. I tried on a PC as well with fresh software. Then I pulled the drives out of the enclosure (warranty is already expired) and plugged them straight into the PC. Both recognized and working 100% in RAID0. BIOS recognizes either disk as functional; Windows only sees them when both are connected due to the RAID which I can't change without the WD software. The drives that were returned to me are the "Green" drives which I've read are NOT recommended for RAID. Is it possible that this is interfering with them reading externally? Any other ideas? My main computer is a laptop so using them internally isn't an option :(

  Read the article

• Why *do* windows print queues occasionally choke on a print job

  - by Ian

  Y'know they way windows print queues will occasionally stop working with a print job at the head of the queue which just won't print and which you can't delete? Anyone know whats going on when this happens? I've been seeing this since the NT4 days and it still happens on 2008. I'm talking about standard IP connected laser printers - nothing fancy. I support a lot of servers and loads of workstations and see this happen a few times a year. The user will call saying they can't print. When you examine the print queue, which in my case will generally be a server based queue shared out to the workstations, you find a print job which you cannot cancel. You also can't pause it, reinitialize it, nothing. Stopping the spooler is the usual trick and works sometimes. However I occasionally see cases which even this doesn't cure and which a reboot is the only solution. Pause the queue, reboot, when it comes back up the job can then be deleted. Once gone the printer happily goes back to its normal state. No action is ever necessary on the printer. I regard having to reboot as last resort and don't like it. What on earth can be going on when stopping the process (spooler) and restarting it doesn't clear a problem? Its not linked to any manufacturer either. I've seen this on HPs, lexmark, canon, ricoh, on lasers, on plotters.... can't say I ever saw this on dot matrix. Anyone got any ideas as to what may be going on. Ian

  Read the article

• Why does my PC successfully boot only when unplugged for more than a few minutes?

  - by philg

  I have an HP Pavilion Elite desktop computer, model HPE-490t. I like it because it didn’t cost too much, boots itself from an SSD, came with 16 GB of RAM, and has 6 CPU cores for editing video and camera RAW images. It has one behavioral quirk that I cannot explain, however. The recent power interruptions here in the Northeast got the machine into a state where it could not be restarted. It would power up for a second or two, shut down, and then power up again, never being able to get to the point of showing anything on the monitor. I unplugged it for about 10 seconds and plugged it back in. Same behavior (fails to boot). I unplugged it and walked away for an hour, then plugged it back in and it worked perfectly! I think something similar happened after installing a second hard disk drive into this machine. So the question is why does the computer behave differently depending on how long it has been unplugged? Where is energy stored that affects the machine’s ability to boot? Capacitors in the power supply? Battery on the motherboard (there is one for the clock, but that wouldn’t be exhausted by being unplugged for an hour, I don’t think)?

  Read the article

• Best Practices for adding Exchange Archive to current 3 server setup

  - by ADquestion

  I'm looking to add an Archive Database (which I know is just a Mailbox Database) to our current Exchange 2010 environment. I have done this in the past at a previous job, but we had a simpler setup than at this current job. I've been trying to find some best practices to make sure it's setup in an ideal way, but so far not finding the details I would prefer. Hoping someone on here can give me a few pointers. Currently we have a 3 server setup, Server1, Server2 and Server3. Three databases of course, DB1, DB2 and DB3. We have a DAG setup between them. Server1 has DB1 and DB3 on it, DB1 is not active, DB3 is active. Server2 has DB1 and DB2 on it, both are active. Server3 has DB2 and DB3 on it, both are not active. All three servers are virtual (VMware). Each one is setup identical to the other as follows: C:\ 60GB - OS E:\ 600GB - DB (currently only 90GB used, pointing to Datastore just for Server2) F:\ 200GB - Log (2GB used, pointing to same Datastore as above) G:\ 200GB - Restore (0 used, pointing to same Datastore as above) The drives are all set to Thin Provisioning, and it looks as though I have 600GB of available space. They have not been on Exchange that long and only have about 70GB worth of PSTs to import back in that will be going to the Archive Database, plus anything older than 2 years from their current inbox that will be moved into there. I was considering placing the Archive DB on the E:\ drive of Server3 (only) like the current DB, but wasn't sure if that was acceptable. I don't plan on setting the Archive DB up with the DAG, just plan on having it as a single repository for older emails and manually back it up every now and then. If anyone has any suggestions on this I would appreciate it the input. I've done it on a slightly smaller scale before and it worked well, but like to think it through before pulling the trigger, especially at a new job. :) Thanks again!

  Read the article

• How to re-add a RAID-10 failed drive on Ubuntu?

  - by thiesdiggity

  I have a problem that I can't seem to solve. We have a Ubuntu server setup with RAID-10 and two of the drives dropped out of the array. When I try to re-add them using the following command: mdadm --manage --re-add /dev/md2 /dev/sdc1 I get the following error message: mdadm: Cannot open /dev/sdc1: Device or resource busy When I do a "cat /proc/mdstat" I get the following: Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [r$ md2 : active raid10 sdb1[0] sdd1[3] 1953519872 blocks 64K chunks 2 near-copies [4/2] [U__U] md1 : active raid1 sda2[0] sdc2[1] 468853696 blocks [2/2] [UU] md0 : active raid1 sda1[0] sdc1[1] 19530688 blocks [2/2] [UU] unused devices: <none> When I run "/sbin/mdadm --detail /dev/md2" I get the following: /dev/md2: Version : 00.90 Creation Time : Mon Sep 5 23:41:13 2011 Raid Level : raid10 Array Size : 1953519872 (1863.02 GiB 2000.40 GB) Used Dev Size : 976759936 (931.51 GiB 1000.20 GB) Raid Devices : 4 Total Devices : 2 Preferred Minor : 2 Persistence : Superblock is persistent Update Time : Thu Oct 25 09:25:08 2012 State : active, degraded Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 Layout : near=2, far=1 Chunk Size : 64K UUID : c6d87d27:aeefcb2e:d4453e2e:0b7266cb Events : 0.6688691 Number Major Minor RaidDevice State 0 8 17 0 active sync /dev/sdb1 1 0 0 1 removed 2 0 0 2 removed 3 8 49 3 active sync /dev/sdd1 Output of df -h is: Filesystem Size Used Avail Use% Mounted on /dev/md1 441G 2.0G 416G 1% / none 32G 236K 32G 1% /dev tmpfs 32G 0 32G 0% /dev/shm none 32G 112K 32G 1% /var/run none 32G 0 32G 0% /var/lock none 32G 0 32G 0% /lib/init/rw tmpfs 64G 215M 63G 1% /mnt/vmware none 441G 2.0G 416G 1% /var/lib/ureadahead/debugfs /dev/mapper/RAID10VG-RAID10LV 1.8T 139G 1.6T 8% /mnt/RAID10 When I do a "fdisk -l" I can see all the drives needed for the RAID-10. The RAID-10 is part of the /dev/mapper, could that be the reason why the device is coming back as busy? Anyone have any suggestions on what I can try to get the drives back into the array? Any help would be greatly appreciated. Thanks!

  Read the article

• Apache reports a 200 status for non-existent WordPress URLs

  - by Jonah Bishop

  The WordPress .htaccess generally has the following rewrite rules: # BEGIN WordPress <IfModule mod_rewrite.c> RewriteEngine On RewriteBase / RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule . /index.php [L] </IfModule> When I access a non-existent URL at my website, this rewrite rule gets hit, redirects to index.php, and serves up my custom 404.php template file. The status code that gets sent back to the client is the correct 404, as shown in this HTTP Live Headers output example: http://www.borngeek.com/nothere/ GET /nothere/ HTTP/1.1 Host: www.borngeek.com {...} HTTP/1.1 404 Not Found However, Apache reports the entire exchange with a 200 status code in my server log, as shown here in a log snippet (trimmed for simplicity): {...} "GET /nothere/ HTTP/1.1" 200 2155 "-" {...} This makes some sense to me, seeing as the original request was redirected to page that exists (index.php). Is there a way to force Apache to report the exchange as a 404? My problem is that bogus requests coming from Bad Guys show up as "successful requests" in the various server statistics software I use (AWStats, Analog, etc). I'd love to have them show up on the Apache side as 404s so that they get filtered out from the stat reports that get generated. I tried adding the following line to my .htaccess, but it had no effect (I'm guessing for the same reason as the previous redirect rules): ErrorDocument 404 /index.php?error=404 Does anyone have a clever way to fix this annoyance? Additional Info: OS is Debian 6.0.4, and Apache version looks to be 2.2.22-3 (hosted on DreamHost) The 404 being sent back to the client is being set by WordPress (i.e. I'm not manually calling header() anywhere)

  Read the article

• How can I backup entire installations of a program, instead of just manually backing up individual f

  - by NoCatharsis

  It seems pretty straightforward to backup individual files, such as pictures, saved games, or settings files - just copy them straight over to your 2nd HDD or to an online service like DropBox. However, is there any way to backup entire installations of a program? For instance, my Firefox directory has a lot of personal customizations and add-ons. I don't want to go through each item and decide to back it up or let it go. So my next option is to copy out the entire directory for backup. But, if I copy the entire directory back onto the HD after a format, it is not an integrated installation and this seems like it could be troublesome. I would assume Windows cannot detect the directory for uninstallation, or would not let you choose Firefox as your default browser, right? I'm no pro, but this sounds like a bad idea. So my question is whether there is a good way to preserve all necessary files, while also preserving the full installation process of an application. This is not specific to Firefox - I would like to know how to do this for any application. Thank you.

  Read the article

• How do I keep a bridge enabled on a bonded interface?

  - by jlawer

  I'm working on setting up a pair of CentOS 6.3 servers that will run a couple of KVM vms and have come across a problem setting up a bridge on a bond. I am using Mode 4 (802.3ad) bonding on a pair of stacked Dell Powerconnect 5524 switches connecting to R320 servers. There are 2 links (1 to each switch) that form a Link Aggregation Group (802.3ad / LACP bonding). On top of the bond I have VLAN Tagging. I've verified this is a problem on multiple other bonding modes so it isn't just a mode 4 issue. I am testing what happens when 1 link is dropped (ie switch dies, cable breaks, etc). If I don't have a bridge (for KVM), everything works fine, failover happens as expected. If I have the bridge enabled, it works fine until failover (unplugging a cable). When failover happens /var/log/messages shows the slave link going down, followed within a second by: kernel: br1: port 1(bond0.8) entering disabled state The thing is /proc/net/bonding/bond0 shows the link is up as expected (simply with only 1 slave instead of 2). If I plug the cable back in it recovers and brings the bridge back to an enabled state. I actually have tested this while a ping is occuring and if the timing is right a packet will actually leave the system after the link is lost, but before the disabled message occurs. This disabled state I assumed was STP, but I have disabled STP on the bridge configuration and this issue still occurs. brctl showstp br1 still shows the link as disabled when it is running without a slave. I also switched between the nics in the server (I have 2x Broadcom & 4x intel). It doesn't matter which configuration I have. Does anyone know of a way to force the bridge to stay enabled or why its detecting the bond as disabled, when it isn't?

  Read the article

• Unable to Connect to just Google Servers

  - by Akshat Mittal

  I am in an extremely strange problem. I am unable to connect to just Google Servers. I am not able to access any site related to Google, Google.com | YouTube | Google+ | Webmaster Tools | jQuery CDN, nothing is working. I am able to open any other website (as I am posting this question on SuperUser), even the Google DNS (8.8.8.8 and 8.8.4.4) are offline. Please Help!! Update 1: Google DNS are back online, YouTube is back online. But website on domain google.com is not working (ex: play.google.com, maps.google.com, google.com/search, etc). Update 2: I am able to access Google.com (only) with (one of) its IP addresss(s) listed below: 74.125.227.41 74.125.227.46 74.125.227.32 74.125.227.33 74.125.227.34 74.125.227.35 74.125.227.36 74.125.227.37 74.125.227.38 74.125.227.39 74.125.227.40 Update 3: I consulted my friends nearby and they said that they are also experiencing the same problem. Seams like this is a major problem in this area (or India !!) The Problem is Now Solved!! I am able to open Google.com

  Read the article

• Cisco 7206 error trying to copy running-config (Bad file number)

  - by jasondewitt

  I have a cisco 7206 that terminates a bunch of pppoa sessions for dsl users. Today I noticed that if I tried to "show run" nothing happened. I mean that it doesn't show anything and just sends me right back to the command prompt. I decided I should probably try and back up the config and that is where I'm stuck. Any time I try to copy the running-config to tftp or to pcmcia card that I know is not full I get the following error: %Error opening system:/running-config (Bad file number) I get this error when I try to do anything with the running config. I've been googling around, but I haven't found any thing else that talks about this error. I've seen people say to erase the nvram and then try to "copy run start", but I don't want to erase the nvram until I can pull off a copy of the running-config. I would try to reboot it, but the startup-config that is on the nvram looks to be woefully out of date (good job me!). Any ideas what might be wrong? or how I can get the running config off the router?

  Read the article

• 500 Error when logining into subdomain using codeigniter

  - by itsdanprice

  I have a website that has been setup and working fine for ages. It's built using Code Igniter. It's run using .htaccess files to restrict access and hide urls. All fine. Until a couple of days ago when we try to access http://admin.dealersupport.co.uk we get a 500 error (this is the back end of the site, held in a seperate subdomain.) Nothing else has changed on the server. I have tried restoring from a back up from when I know it was working. The problem persists. The only thing I can think of is that we recently upgraded to Plesk 11.0.9 and since then we have been seeing some Apache instabilities. The only thing that is thrown up by the error logs is this: Wed Nov 21 08:40:17 2012] [error] [client 94.31.24.129] Options FollowSymLinks or SymLinksIfOwnerMatch is off which implies that RewriteRule directive is forbidden: /var/www/vhosts /dealersupport.co.uk/admin/index.pl, referer: http://admin.dealersupport.co.uk/login I have now added this to my .htaccess files Options +FollowSymLinks +SymLinksIfOwnerMatch RewriteEngine On And that seems to have eliminated that error from the error logs, but we are still getting a 500 error when we have logged into the backend. Can anyone help?

  Read the article

• Webcam becomes "Unknown Device" after Windows Messenger 2011 is installed

  - by Boris

  I have Sony VAIO VGN-NS290J laptop. I installed Windows 7 Ultimate 64-bit. I was able to find drivers for all hardware without any problems. Recently, I installed Microsoft Windows Live Essentials 2011, i.e. Windows Live Messenger 2011. Ever since that application is running on my computer, my webcam is not recognized by the OS any more. It is listed as the "Unknown Device" and placed in the Universal Serial Bus controllers group in the Device Manager. There don't seem to be any drivers for this webcam. It's a standard Sony Motion Eye web camera and Sony does not offer any drivers for it. There is one application to download that utilizes the camera, but there are no drivers (and the system is showing the same behavior regardless of the presence of the application). It happens from time to time that the webcam becomes recognized by the OS again, after a couple of restarts; but not always. Then it becomes unknown again. I am absolutely positive that this issue is caused by the Windows Live Messenger 2011, because same symptoms caused the same effects before. I wish to be able to continue to use this software, but also to use my webcam. I was wondering if anyone had a similar issue and if there is a way to fix it. Thanks for all the help, I appreciate it. Update: I have discovered a pattern - if the camera goes astray, restarting the machine does not bring it back; but switching the computer off and turning it back on does. Every time! This is getting super complicated :)

  Read the article

• Windows 7 - media sharing extremely flakey (XBox 360)

  - by Nathan Ridley

  I have constant headaches with Windows Media Library sharing, which I'm using to share my video library (a whole lot of AVI files on my computer's hard drive) with the XBox 360. I have the whole setup working, so setup and basic configuration is not an issue. The issue is that Windows Media Library frequently fails to notice additions and modifications to the "watched" folders. Not only that, but often after I've added something new to the library, it fails to transmit this new library information to the 360, as is demonstrated by the fact that, using that 360, I navigate to my video library and the new folders don't show up in the list. Often the only way to get the 360 to see the changes is to exit out of "Videos" on the 360, then remove all videos from Windows Media Library, go back into videos on the 360 to confirm that nothing is shared, then re-add a few videos (but not too many) in Windows Media Library, then go back into the videos in the 360. The whole thing is a real pain in the bum and I really wish I could just add all my videos to Windows Media Library and have it keep watch without me having to kick it, and have the 360 pick up changes without me having to constantly rebuild the library. Any ideas?

  Read the article

• VPS to replace MobileMe or Google Apps.

  - by Alex

  All, Yes, this has been touched on in other questions, but I can't find something similar enough. I currently have Google Apps hosting personal email, calendars, contacts, etc. I do like the other google services, but they're outside of Apps. One of the little google irritations that I have to maintain a separate account for Picassa, etc. So, I'm thinking about moving myself away from Google, but purely for personal, privacy type issues. Do I really like the ads, the email snooping, etc? I've had, and liked MobileMe, back when it was iTools, and then .Mac, but it doesn't offer that much really. How easily can I replicate it all on a VPS? I don't want to host it myself at home, I'd lose all the wonderful datacenter goodness. THis isn't about personal geekery in my own basement, just about taking a little control back from Google. So, email is fine running an IMAP server, a nice front-end, etc. What about Calendars and Contacts? And, how easily can it be setup to sync to the desktop and iPhone? Thanks.

  Read the article

• How to send from my Z88 to my PC

  - by Bevan

  I've got a Cambridge Z88 that I want to get working with my PC. Around 6 years ago - in 2004 - I made heavy use of my Z88 to do a whole bunch of writing on the train while commuting to and from work. The Z88 is solid state, lightweight and has a full size silent keyboard, so it works very well as a writing instrument. I still have the serial cable I soldered up back then and used successfully in 2004. It has these connections: Z88 9 pin ----- ------- 2 TxD ------> RxD 2 3 RxD <------ TxD 3 7 GND <-----> GND 5 4 RTS ------> CTS 8 5 CTS <-+ RTS 7 8 DCD <-+---- DTR 4 9 DTR ----+-> DCD 1 +-> DSR 6 Unfortunately, I haven't been able to find my notes from 2004 that describe how I got it to work back then. I've spent several hours trying to Google a result, but to no avail. I'm pretty sure the cable is fine - after all, it's what I used successfully six years ago, and I've checked it out with a multimeter - so I'm focusing on the PC end of things, which is where I'd like some assistance. Q1: In my recent attempts, I've been using both Hyperterminal (as built into Windows XP) and the command line (copy com2: con:), but with no success. What's a good (better!) serial communications application to use? Is there one that allows me to see as deep as the signalling that's occurring on the wire? Q2: If you have a Z88 that works correctly with your PC, what software do you use on the PC end, and what's the pinout of your cable? I'm pretty sure that the Z88 itself is working properly: When using the built in Import/Export tool to send a file, I see different behaviour when my serial cable is connected compared to disconnected. When disconnected, the transmission appears to work, with a progress meter counting up and then finishing; when connected, nothing happens 'cept a timeout if I wait long enough.

  Read the article

• MySQL getting stuck, eating up disk i/o

  - by bonez05

  Hi all, Using mySQL 5.0.51 on Solaris . At intermittent times it looks like MySQL is getting 'stuck' . The disk usage on the server spikes to 98% busy from reads. I used dtrace (specifically DTrace toolkit - iosnoop) to track down what processes was using all the reads. Mysql was calling tablename.TDM hundreds of times per second. There was no more than average load on the webserver that could account for this. There were no cronjobs running, and no other utilities like mysqldump or anything. It is a master / slave replication setup. As a jury-rigged fix, I altered the mysql table from 'tablename' to 'tablename2' and then back to 'tablename' This fixed the problem temporarily, and "unsticks" mysql. The disk usage goes back down and dtrace is no longer showing hundreds of reads to 'tablename.TDM' / second. A couple ideas I had are: 1. MySQL version bug 2. Infinite loop somewhere in my application (which i'm not sure how likely this is) 3. ?? Has anybody seen this before or have any insight? Thanks

  Read the article

• What is the quickest and safest way to test new software and revert all changes, if needed?

  - by calbar

  I'm looking for Windows software that will allow me to quickly create a "checkpoint", do whatever I might need to do to my computer - install programs/drivers/updates, create/delete personal files, reboot the system multiple times, open questionable attachments - and then revert the entire system back to when the checkpoint was created. Essentially I want Windows Restore Points that save my personal files and partitions, too. It sounds like disk imaging might be the ticket, but creating them is much too slow and the restore process too involved... I'm hoping to sacrifice full disaster recovery for speed. Creating a checkpoint should be as close to one-click as possible, and rolling back should be a matter of selecting a restore point and rebooting. Ding! I'm familiar with Sandboxie, True Image Home "Try and Decide", Returnil, and a number of other "virtual system" apps that actively "catch" changes and allow you to commit or reject them. I'm not interested in these for a number of reasons - I prefer the "cut and dry" restore point approach. Finally, I'll note that I've just recently become aware of Comodo Time Machine. It sounds absolutely perfect, however, a quick skim through the user forums show more than a few horror stories of corrupted, unbootable systems. Any positive personal experience with the software to suppress my superstitions, or suggestions for more established alternatives would be greatly appreciated - Comodo Time Machine seems relatively new. Thanks for your help!

  Read the article

• Keyboard doesn't function after Fedora 17 update

  - by mickburkejnr

  I updated my Fedora 16 installation to Fedora 17 on Saturday, and the update worked without reporting any errors. I carried on working on the machine in question and then switched the computer off. Last night I went back on the computer, I switched it on and got to the log in screen. At this point I tried to type in my password but the keyboard wouldn't work. I unplugged it (it's a PS/2 keyboard) and plugged it back in. The lights flashed for a split second but the keyboard still wouldn't work. I then plugged the keybaord in to a USB to PS/2 adapter, and the keyboard still wouldn't work. I restarted the computer and tried to access the BIOS and I was able to do so. So the keyboard doesn't seem to be faulty, it just doesn't work when Fedora boots in to the GUI interface. I did try to boot in to the "recovery mode" of Fedora, and the keyboard works here with no problem. As I still have access to Fedora via a terminal interface, is there anything I can do to fix the keyboard problem via the terminal without having to reinstall Fedora?

  Read the article

• VLAN Tagging Traffic on Cisco Switch

  - by David W

  I have a situation where I'm setting up multiple VLANS on a pfSense firewall on the same physical interface for a client. So in pfSense, I now have VLAN 100 (employees) and VLAN 200 (students - student computer lab). Downstream from pfSense, I have a Cisco SG200 switch, and coming off of the SG200 is the student lab (running on a Catalyst 2950. Yes, that's old, but it works, and this is a poor nonprofit we're talking about). What I'd like to do is tag everything on the network as VLAN 100, except for the student computer lab. Earlier today when I was on-site with the client, I went into to the old Catalyst 2950, and assigned all of its ports to access VLAN 200 (switchport mode access vlan 200) without setting up a trunk on the Catalyst or on the SG200. Looking back on it, I now understand why internet in the lab broke. I reverted the lab back to the default VLAN1 (we're still running on a different firewall - we haven't deployed pfSense -, and the traffic is still separated physically). So my question is, what do I need to do in order to properly deploy this scenario? I believe the correct answer is: Ensure VLANs 100 and 200 are setup in pfSense, and that DHCP is operating correctly (on separate subnets) Setup a trunkport VLAN that allows both 100 & 200 traffic, and plug that port directly into pfSense. Setup a VLAN 200 trunkport on the SG200 (It's not running iOS, but if it were, the command would be switchport trunk native vlan 200), which will then plug into the Catalyst 2950. Setup a VLAN 200 trunkport on the Catalyst 2950 (that is plugged into the SG200 VLAN200 port with the same command - switchport trunk native vlan 200) Setup the rest of the ports on the old Catalyst 2950 in the lab to be access ports on VLAN200. Is there anything that I'm missing, or do I need to tweak any of these steps, in order to properly segment the network traffic?

  Read the article

• ActiveDirectory user files aren't being shared? [on hold]

  - by Ryan

  I'm taking a class in college and my current project is to setup Active Directory. So I have two VMs, one is Windows Server 2008 R2 and the other is Windows 7. I setup the domain team15.net (this is the FQDN for the forest) on the W2008 server machine. And then I connected the Windows 7 machine to the team15.net domain, and now I can login to the administrator account on the W2008 machine by using TEAM15\Administrator for the username. However, any files that I add in Windows 7 while logged into TEAM15\Administrator are NOT shown in the Windows 2008 machine. Is this normal? It seems like any files I add to this user in the domain only exists for the machine that I'm currently using. Is it possible to change this so all files for all users are synced to all computers in the domain? If not then what are alternatives? I noticed that back in high school we also used domains but there was a shared drive E:\ that you had to store your files because if you put them on in the desktop instead then they would suddenly disappear once you logged out and back in. How can I setup a shared drive? and which computer would provide the storage for this drive?

  Read the article

• Microsoft Mouse and Keyboard Center Needed for Keyboard but Doesn't Support Mouse

  - by eljay

  I recently built a new computer (running Win7 Pro 64-bit) that includes the Microsoft Sidewinder X4 Keyboard. To make use of all the extra features of this keyboard I need the Mouse and Keyboard Center. I just ran Windows Update for the first time on this system and the Mouse and Keyboard Center was included in the update. I'm left-handed and before the update I had the mouse set up for lefty use. Now after the update, it's been set to righty use and the original mouse control panel applet no longer allows the assignment of buttons. For that there's a link to the Mouse and Keyboard Center which does not support my oldish mice. (I have an IntelliMouse Optical and a Creative Mouse Lite Pro.) So I need the new utility for my keyboard, but I have to be right-handed to use my mouse? Really! I tried changing HKCU\Control Panel\Mouse\SwapMouseButtons to 1, but a reboot set it back to 0. Is there some way I can change my mouse back to left-handed? Thanx -eljay

  Read the article

< Previous Page | 198 199 200 201 202 203 204 205 206 207 208 209  | Next Page >