Search Results

Search found 15896 results on 636 pages for 'gnome settings daemon'.

Page 202/636 | < Previous Page | 198 199 200 201 202 203 204 205 206 207 208 209  | Next Page >

• Wireless keeps disabling or stays disconnected (Realtek RTL8191SEvB)

  - by jindrichm

  I have Realtek RTL8191SEvB wireless card on Ubuntu 10.10: $ lspci -v | grep Network 03:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8191SEvB Wireless LAN Controller (rev 10) When I load its driver, according to the Network Manager it sometimes blinks with a list of available networks but it keeps disabling itself or it stays disconnected. So, I can't connect to any wi-fi network (which results in frustration). The driver is loaded: $ lsmod Module Size Used by r8192se_pci 509932 0 Looks normal: $ sudo lshw -C network *-network description: Wireless interface product: RTL8191SEvB Wireless LAN Controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 10 serial: 1c:65:9d:60:c7:7a width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rtl819xSE driverversion=0019.1207.2010 firmware=63 latency=0 link=no multicast=yes wireless=802.11bgn resources: irq:17 ioport:2000(size=256) memory:f0500000-f0503fff Configured: $ sudo iwconfig wlan0 wlan0 802.11bgn Nickname:"rtl8191SEVA2" Mode:Managed Frequency=2.412 GHz Access Point: Not-Associated Bit Rate:130 Mb/s Retry:on RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=10/100 Signal level=0 dBm Noise level=-100 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 Is not blocked: $ rfkill list all 0: tpacpi_bluetooth_sw: Bluetooth Soft blocked: no Hard blocked: yes However something's happening with it: $ dmesg [ 6485.948668] InitializeAdapter8190(): ==++==> Turn off RF for RfOffReason(1073741824) ---------- [ 6486.062666] rtl8192_SetWirelessMode(), wireless_mode:10, bEnableHT = 1 [ 6486.062671] InitializeAdapter8192SE(): Set MRC settings on as default!! [ 6486.062675] HW_VAR_MRC: Turn on 1T1R MRC! [ 6486.064091] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 6486.248761] rtl8192_SetWirelessMode(), wireless_mode:10, bEnableHT = 1 [ 6486.248771] InitializeAdapter8192SE(): Set MRC settings on as default!! [ 6486.248776] HW_VAR_MRC: Turn on 1T1R MRC! [ 6486.580083] GPIOChangeRF - HW Radio OFF [ 6486.610085] ============>sync_scan_hurryup out [ 6486.623814] ================>r8192_wx_set_scan(): hwradio off [ 6486.830484] =========>r8192_wx_set_essid():hw radio off,or Rf state is eRfOff, return So, does anyone know where the problem might be?

  Read the article

• AppleTV - itunes store is temporarily unavailable - please check back later

  - by Ken

  When attempting to rent a movie on ATV, my wife received the error message above.  Alternately “server unavailable”.  When your wife is sick, the amount of IT support she needs goes up exponentially.  One piece of the puzzle was that she had changed her Apple ID password.  On her PC I ran iTunes and under account, there was only 1 device listed (not the ATV).  Even when signed out/back-in on the ATV under Settings>iTunes it still gave same error message.  What I suspect is it thinks she is trying to authorize the device to another Apple ID.  Some new 90 day rule limits when a device can be associated with another Apple ID.  Your iTunes store/account will show devices, and how long before they can be associated with a different Apple ID from the Account Information page in iTunes on your computer.  Apple must have no freaking idea why someone would want to know which ID is associated to the ATV (i.e. the vice versa), because it can’t be done. Solution: Try ATV settings>reset I swapped out ATV 1 for ATV 2 (used for music streaming downstairs).  I know it’s a cop-out solution, but remember I had a sick wife breathing down my neck.

  Read the article

• Nvidia GeForce Gt-520M-cn on intel dh61ww Ubuntu 12.04

  - by j goseeped

  hi people i hope you can help a little bit , i appreciate your time look: i have a this desktop i7 2600, 8gb ram ddr3, board intel dh61ww, Geforce Nvidia GT520-cn 2Gb ddr3, i just install ubuntu 64bits 12.04 kernel 3.2.0-23-generic , i want to setup two monitors samsung led 22" and get start mi video card 1) i download and installed nvidia driver 295.59 and also try with 302.17 to apt-update and upgrade, apt-get install build-essential linux-headers-$(uname -r), apt-get remove --purge nvidia*, apt-get remove --purge xserver-xorg-video-nouveau, vim /etc/modprobe.d/blacklist.conf blacklist vga16fb blacklist nouveau blacklist rivafb blacklist nvidiafb blacklist rivatv sh NVIDIA.run, sudo service lightdm start, reboot, nvidia-xorgconf 2)after reboot i get 800x600 and nvidia-settings say this. You do not appear to be using the NVIDIA X driver. Please edit your X configuration file (just run nvidia-xconfig as root), and restart the X server. 3) i change a little bit xorg.conf to set up a resolution to work property 4) i dont have any image in the monito and i dont have any option on Nvidia X server settings lspci | grep VGA 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 01:00.0 VGA compatible controller: NVIDIA Corporation GF119 [GeForce GT 520] (rev a1) egrep -i 'glx|nvidia' /var/log/Xorg.0.log [ 12.005] (II) LoadModule: "glx" [ 12.005] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so [ 12.575] (II) Module glx: vendor="NVIDIA Corporation" [ 12.585] (II) NVIDIA GLX Module 302.17 Tue Jun 12 16:22:45 PDT 2012 [ 12.585] (II) Loading extension GLX [ 13.037] (EE) Failed to initialize GLX extension (Compatible NVIDIA X driver not found) [ 13.044] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=3 (/dev/input/event10) [ 13.044] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=7 (/dev/input/event9) glxinfo | grep direct Xlib: extension "GLX" missing on display ":0.0". Error: couldn't find RGB GLX visual or fbconfig sorry my english is no very well. and thanks guys

  Read the article

• Weird bug in Visual Studio 11 Beta when running on Windows 8

  - by raccoon_tim

  With the Windows 8 Consumer Preview version out in the open and the Visual Studio 11 Beta also available, I’ve been putting some more effort into trying them both out. The first impression of the new Visual Studio 11 build was: Why doesn’t it work at all on Windows 8?! The issues I encountered were odd to say the least. Visual Studio did install correctly, which was a good sign, but when I started it, I was greeted with a multitude of popups each telling me that some package could not be loaded. So I clicked away for quite some time to finally be greeted by the new default visual style of Visual Studio. The next thing I wanted to do was start a new project so I pressed “New Project” and got the “Microsoft.VisualStudio.Dialogs.DialogInitializationException” exception. After some pondering and even submitting a bug report I found another already reported bug “http://connect.microsoft.com/VisualStudio/feedback/details/727578/vs-do-not-work-with-finnish-number-format-on-w8-64-bit”. It turns out that the dialog initialization failure has something to do with the packages no being loaded and following the presented workaround helped. The trick is to change the negative number sign to “-“ (U+002D) from the additional settings of your regional settings. This issue appears to have a wider reach than just Visual Studio as I heard at TechDays Finland 2012 that the same fix has to be made when using Hyper-V.

  Read the article

• Nvidia driver installation results in resolution change to 800x600 with Xubuntu 10.04 (can't change)

  - by Jim Michael

  I have a 2.8 P4 and a Nvidia FX 5500 AGP graphics card. I've installed Xubuntu 10.04. It is WAY too laggy with the default o/s driver. Installing the Nvidia 173 driver, modaliases and nvidia-settings packages via synaptic package manager results in the following error message: An error occurred, please run Package Manager from the right click menu or apt-get in a terminal to see what is wrong. Error: Opening the cache (E::read, still have 11898251 to read but none left, E: The package lists or status file could not be parsed or opened.) This usually means that your installed packages have unmet dependencies. When restarting the PC the resolution drops to 800x600 (from the monitors native 1440x900). Nvidia settings cannot be changed either from the Xfce menu or Nvidia Xserver. Nvidia Xsever gives the following error message: You do not appear to be using the Nvidia X driver. Please edit your x configuration file (just run 'nvidiaxconfig' as root ) and restart X server. Also, I can't find anything in any directory called xorg.

  Read the article

• XNA 4: RenderTarget2D textures getting transparent on fullscreen

  - by Shashwat

  I'm generating a Texture2D object using RenderTarget2D as in the following code public static Texture2D GetTextTexture(string text, Vector2 position, SpriteFont font, Color foreColor, Color backColor, Texture2D background=null) { int width = (int)font.MeasureString(text).X; int height = (int)font.MeasureString(text).Y; GraphicsDevice device = Settings.game.GraphicsDevice; SpriteBatch spriteBatch = Settings.game.spriteBatch; RenderTarget2D renderTarget = new RenderTarget2D(device, width, height, false, SurfaceFormat.Color, DepthFormat.Depth24Stencil8, device.PresentationParameters.MultiSampleCount, RenderTargetUsage.DiscardContents); device.SetRenderTarget(renderTarget); device.Clear(backColor); spriteBatch.Begin(SpriteSortMode.Immediate, BlendState.Opaque); if (background != null) spriteBatch.Draw(background, new Rectangle(0, 0, 70, 70), Color.White); spriteBatch.End(); spriteBatch.Begin(); spriteBatch.DrawString(font, text, position, foreColor, 0, new Vector2(0), 0.8f, SpriteEffects.None, 0); spriteBatch.End(); device.SetRenderTarget(null); ResetGraphicsDeviceSettings(); return (Texture2D)renderTarget; } It's working all fine. But when I ToggleFullScreen() (and vice-versa), the previous textures are getting transparent. However, the new textures after that are being generated correctly. What can be the reason for this?

  Read the article

• Why does my mic boost automatically go to 100 on every boot?

  - by Ben

  When my computer turns on, it automatically sets the "mic boost" sound setting to 100. This causes a loud static sound in my speakers. I can manually go to alsamixer and turn the mic boost down manually, but I would prefer it if I didn't have to do this every time I turn the computer on. I've tried running sudo alsactl store after fixing the settings, and this does save them, but I have to run sudo alsactl restore to restore the settings. This means that I have to manually fix the sound every time I start the computer anyway, so it isn't really a fix. I tried putting sudo alsactl restore in my startup programs, but that didn't seem to fix anything. I'm running Ubuntu 12.04, but I started having this problem before upgrading from 11.10. I'm using a Sony Vaio laptop. I'm not really sure what made it start; it seemed like I just started having the problem randomly one day. Any help would be appreciated! Edit: here is the output from running amixer: http://paste.ubuntu.com/1060080/

  Read the article

• Unable to make sound play in headset

  - by user50849

  Top right, I click the sound icon, select sound settings, and connect my USB-headset. I can them see the headset being detected as it pops up in the menu. I click it, and expect the currently played audio to get sent to the headset instead. My problem is that it does not. The audio keeps playing through the built-in speakers. More info: The icon for my built-in card in the sound settings is a circuit with a note symbol on top. The symbol for the headset is just black background with a "No" symbol on it. Might mean it doesn't work somehow. I installed pavucontrol, and notice that no second sound card shows up in there. When connecting, the syslog says Jun 20 09:38:46 yuna kernel: [40144.553431] usb 2-1.2: new full-speed USB device number 11 using ehci_hcd Jun 20 09:38:46 yuna kernel: [40144.650609] input: C-Media USB Headphone Set as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.3/input/input20 Jun 20 09:38:46 yuna kernel: [40144.650895] generic-usb 0003:0D8C:000C.000B: input,hidraw0: USB HID v1.00 Device [C-Media USB Headphone Set ] on usb-0000:00:1d.0-1.2/input3 Jun 20 09:38:46 yuna mtp-probe: checking bus 2, device 11: "/sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2" Jun 20 09:38:46 yuna mtp-probe: bus: 2, device: 11 was not an MTP device

  Read the article

• How do I get HDMI output working on a Dell XPS 15 L502x?

  - by Jones

  Recently I've bought my dream's notebook, a Dell XPS 15 but since then this dream became a kind of endless nightmare. I'm almost getting crazy to make my graphic card driver work properly, but it seems to be just impossible. Yes, I have a 2GB NVIDIA GeForce GT 540m (Optimus) in it! It simply doesn't work. Every time I generate the xorg.conf Ubuntu hangs on while starting up, which forces me to remove this file to be able to start the notebook with the standard graphic settings. Another problem is that the Dell XPS 15 does NOT have a VGA output, but a HDMI. So, to be able to use a second monitor I have to configure it by the NVIDIA X Server Settings, which just works if the driver is properly initialized with the xorg.conf. I've also tried to make it work with the Bumblebee, but unfortunately it didn't help me much with the HDMI output. Do you guys have any idea to solve this deadlock? Is there any way for me to use my second monitor?

  Read the article

• How do I get a different type of scrollbars in 12.04? [closed]

  - by Joseph Garvin

  Possible Duplicate: How do I disable overlay scrollbars? By default 12.04 uses overlay scroll bars that do not suit my taste, and every method I've found so far of disabling them makes them broken in a different way. When I was using 11.10 this wasn't a problem because I could still change the GTK theme. In 12.04, the Appearance settings only contain a few stock themes, and other than the special purpose contrast ones they all have the overlay scroll bars. If I aptitude search gtk3 | grep theme I get no results so there appears to be no packaged alternative either. Most suggestions I've seen for disabling the overlay scroll bars involve uninstalling packages or editing files as root. I want to disable them just for the current user, not for everyone on the whole box; as should be the case for any theme/display setting. There is a gsettings command that temporarily disables the overlay scrollbars just for the current user, but this has two problems of its own: The setting doesn't stick after log off. Because who would want to save settings? The scroll bars put in place have no contrast. They have a black scroller on a black background and are completely unusable. In short what I'd like to know is how to disable overlay scroll bars such that: My preference is user specific. My preference is actually saved. The scroller can actually be seen against the background without having to use a special high contrast theme that makes my whole desktop look like a negative photo from Tron.

  Read the article

• Having extreme issues getting Compiz working on Ubuntu 11.10 (32-bit)

  - by Josh Hornell

  I have been working very hard the past few days to try to get Compiz configured and working correctly but I have been running into a lot of issues. I first installed the CompizConfig Settings Manager and tried different features such as the desktop cube and couldn't get any of them to work. Then I read that I may not have the right graphics card drivers installed (Nvidia GT540m). So I went into the Additional Drivers tool and it shows that 'no proprietary drivers are in use on this system', which struck me as a bit odd as when I very first installed Ubuntu it showed that my Nvidia drivers were installed an active until I downloaded and installed the updates to Ubuntu and since then it's shown empty. I then tried to install my graphics card drivers manually via this article How do I install the latest Nvidia drivers via the Additional Drivers tool?. I rebooted and had no issue although I tried to go back into the CompizConfig Settings Manager and couldn't get anything to work as well as my Additional Drivers tool still showed no drivers installed. I feel like I've tried about everything I can think of and any help would be much appreciated!

  Read the article

• How to ask developers to think about high resolution screens

  - by WhiteWind

  I just got a ASUS N56VZ laptop, and it`s all good, but the screen resolution 1920x1080px. I am not asking, how to scale ui elements. If someone is interested I have found some tricks: increase font size in system settings increase unity dock size in MyUnity or system settings in modern Ubuntu versions. tweak userChrome.js of FireFox to make buttons|panels|icons larger add DefaultZoomLevel extension to FireFox to make it zoom pages initially. But all of it is miserable, because there are some big bugs: window decoration elements are way too small to pick them with mouse. I can't scale window easily and I can't position my cursor fast on the close|maximize buttons. Tuning lines like in sound volume dialog are hardly clickable at all. Unity top panel (status panel & tray) hardly can contain the bigger font, so it looks ugly, but icons are still the same. Sometimes I can`t read text, as it is cropped (and I cant scale some dialogs as it has fixed size) Chromium is not usable at all (ok, it's not Ubuntu problem, but the problem still exists) JAVA applications are not scalable (same as above) In FF I am able to get descent results in most cases, but multiplication of system font increase and browser font increase makes system controls (combobox, lists, drop down lists) extremely big, so I cant even control the zoom level on the page. IMHO, we should post a bug report (but what kind of bug?) and vote for it! The problem is even deeper, but at least we should ask developers to think about it. So my question is: how can I post a report (the right words and right place) and how can we (who already has that problem, or who want it to be solved before hardware upgrade) vote for faster solution. Any ideas?

  Read the article

• M-Audio Delta 1010LT on 12.04

  - by user74039

  I have 12.04 64bit installed, my soundcard is a Delta 1010LT, it seems to be partially detected, I've been following steps here: https://help.ubuntu.com/community/SoundTroubleshooting/ lspci -v | grep -A7 -i "audio" shows this: 04:07.0 Multimedia audio controller: VIA Technologies Inc. ICE1712 [Envy24] PCI Multi-Channel I/O Controller (rev 02) Subsystem: VIA Technologies Inc. M-Audio Delta 1010LT Flags: bus master, medium devsel, latency 64, IRQ 22 I/O ports at ec00 [size=32] I/O ports at e880 [size=16] I/O ports at e800 [size=16] I/O ports at e480 [size=64] Capabilities: <access denied> Kernel driver in use: snd_ice1712 aplay shows this: **** List of PLAYBACK Hardware Devices **** card 0: M1010LT [M Audio Delta 1010LT], device 0: ICE1712 multi [ICE1712 multi] Subdevices: 1/1 Subdevice #0: subdevice #0 In the sound settings on the desktop all I see is the ICE1712 S/PDIF, which I don't use, I want to use the individual outputs on the card, I'm not so bothered about inputs, I just want the playback for now. If I open alsamixer in the console, I see all of the output and input channels, i've raised the volume on them but I don't get anything in the sound settings on the desktop and when I play any sound, I hear nothing. Can someone help?

  Read the article

• How to force ADF to speak your language (or any common language)

  - by Blueberry Coder

  When I started working for Oracle, one of the first tasks I was given was to contribute some content to a great ADF course Frank and Chris are building. Among other things, they asked me to work on a module about Internationalization. While doing research work, I unearthed a little gem I had overlooked all those years. JDeveloper, as you may know, speaks your language - as long as your language is English, that is. Oracle ADF, on the other hand, is a citizen of the world. It is available in more than 25 different languages. But while this is a wonderful feature for end users, it is rather cumbersome for developers. Why is that? Have you ever tried to search the OTN forums for a solution with a non-English error message as your query? I have, once. But how can you force ADF to use English for its logging operations? Playing with your system settings will not help, unfortunately. By default, ADF will output its error messages in the selected locale for the operating system account the application server runs on. The only way to change this behavior is to pass initialization parameters to the JVM used by the application server. It is even possible to specify the language and country/region separately. In the example below, we choose English and the United States respectively. -Duser.language=en -Duser.country=US In the case of WebLogic Server, it is possible to add such parameters in setDomainEnv.sh (or .cmd) to apply the settings to all the managed servers present on a node. In the coming weeks, I will write a few posts about other internationalization issues. Is there anything you would like me to cover? Let me know in the comments.

  Read the article

• Client-server application design issue

  - by user2547823

  I have a collection of clients on server's side. And there are some objects that need to work with that collection - adding and removing clients, sending message to them, updating connection settings and so on. They should perform these actions simultaneously, so mutex or another synchronization primitive is required. I want to share one instance of collection between these objects, but all of them require access to private fields of collection. I hope that code sample makes it more clear[C++]: class Collection { std::vector< Client* > clients; Mutex mLock; ... } class ClientNotifier { void sendMessage() { mLock.lock(); // loop over clients and send message to each of them } } class ConnectionSettingsUpdater { void changeSettings( const std::string& name ) { mLock.lock(); // if client with this name is inside collection, change its settings } } As you can see, all these classes require direct access to Collection's private fields. Can you give me an advice about how to implement such behaviour correctly, i.e. keeping Collection's interface simple without it knowing about its users?

  Read the article

• Disable touchpad tap to click on Oneiric ocelot

  - by AWE

  You've heard this a million times but the "tap to click" is a pain in the behind and I want to disable it. There is no touchpad in gpointing-device-settings and neither in mouse and touchpad in system settings. I've tried some commands in terminal but it's all crap. Dconf-editor doesn't react. How about solving this once and for all? xinput list: ? Virtual core pointer id=2 [master pointer (3)] ? ? Virtual core XTEST pointer id=4 [slave pointer (2)] ? ? PS/2 Generic Mouse id=13 [slave pointer (2)] ? Virtual core keyboard id=3 [master keyboard (2)] ? Virtual core XTEST keyboard id=5 [slave keyboard (3)] ? Power Button id=6 [slave keyboard (3)] ? Video Bus id=7 [slave keyboard (3)] ? Video Bus id=8 [slave keyboard (3)] ? Power Button id=9 [slave keyboard (3)] ? Sleep Button id=10 [slave keyboard (3)] ? Laptop_Integrated_Webcam_HD id=11 [slave keyboard (3)] ? AT Translated Set 2 keyboard id=12 [slave keyboard (3)] ? Dell WMI hotkeys id=14 [slave keyboard (3)]

  Read the article

• Crackling sound from microphone recently, in 13.04

  - by Patrig Droumaguet

  I use 13.04 since the release and I use Skype which was working well. But recently I've had remarks saying my voice was "crackling", even if the voice from my interlocutor was perfect. Making a test with Audacity and Cheese, I've seen that every recorded sound (with the front microphone of my laptop or a jack microphone) was crackling. It's not really like saturating, the sound has a lot of annoying pops. I've tried to check the settings, they were still on PulseAudio. I've even tried the extreme solution : re-installing Ubuntu (because initially it was working)… with the same problem. If I boot on Windows (dual-boot) I have no problem (so it's not physical). If anyone could help :) My laptop is a HP dv6-6165sf. The sound card is a "IDT 92HD81B1X5" (with BeatsAudio). Thanks a lot ! New tests - july 6th Hi again, I've tried editing /etc/pulse/default.pa with these three settings : load-module module-udev-detect use_ucm=0 tsched=0 load-module module-udev-detect tsched=0 load-module module-udev-detect use_ucm=0 The three of them don't change anything, except the last one (which was by default) which makes Audacity record without any crackling sound. But in Skype, Cheese and Kazam, the sound is crackling… I've installed again Ubuntu 13.04 (from scratch, deleting everything from /home), and I've updated it. The microphone is still cracking. Thanks for your help !

  Read the article

• My sound is not working, so I'm going to reinstall FYI [closed]

  - by fer

  I've had trouble getting the sound to work in Ubuntu 12.04 I'm running an Acer Aspire 5739g laptop. This is using a clean install. This wasn't a problem when ubuntu first installed. Rather, it was when I ran the updates that it stopped working. I already tried the suggestions on the ubuntu sites and other similar queries, and they haven't fixed it. Something in the updates is making my sound not work. Edit: It turns out that this might be a bug (the sound issue, first paragraph). After reinstall, it happened again (it's not caused by updates at all, or any software, because I fixed it now w/o reinstall). It seems like I replicated it as follows: I changed auto-hide in the behavior tab of Appearance settings by turning it on, and setting the sensitivity to below the recommended setting. Then instead of restarting, I just logged out and back in. The sound stopped working again. I set the behavior settings to default, restarted, and now it's back to normal. Not sure if it's due to only logging out (and not restarting) or b/c I set my sensitivity to a low setting. Not sure if this helps anyone, but thought I'd mention it.

  Read the article

• Not recognized as operating system on startup

  - by mastabruce

  I am new to Ubuntu and just decided to install it in (on my new lenovo thinkpad) in addition to my windows 7 operating system. Now, whenever I reboot the computer, it only runs window 7. I went (in windows) to Control Pannel ? System ? Advanced Settings ? Startup and Ubuntu is not even listed as a choice for operating system. I tried installing ubuntu again, but now it wants to partition the already partitioned windows folder. I can't figure out how to get Ubuntu, which seems to be installed, to run. I saw on another question here that I could be able to edit my mrb settings using EasyBCD but I can not figure out how to choose ubuntu as an operating system. My disk is already partitioned (seen from the attempted second install) so I'm pretty sure it is on the disk. Basically, how can I get ubuntu to run when I can't choose it as an operating system? Thank you for your help.

  Read the article

• Compiz problems in Ubuntu 12.10

  - by Antonio Raffaele Iannaccone

  I have installed ubuntu 12.10 x64 on my notebook and I wanted to make a little customization in the UI, so i downloaded Compiz Settings Manager and opened it up. Once I opened it up, I found out that in the compiz are not all those settings and animations (that I could apply like on the photos, videos etc.) so I reinstalled it few times. Once I get bored with the reinstalling I checked one field in there and Ubuntu (OS) started to get "lagged" (Dash get hid, OS started to do not respond very well). So please, can anyone help me? How can I customize my ubuntu without get lagged and with all the animations that have to be available in the compiz? Thanks to all! thank you! It seems that it helped to fix the Dash-hide problem, but I still do not have all the animations and features that have to be in the Compiz (program). Can you help me with this too please? Thanks a lot!

  Read the article

• WiFi problems on several Ubuntu installations

  - by Rickyfresh

  Okay this is the first time I have ever had to ask a question as usually the Ubuntu community have answered everything already but on this occasion there are many people asking for the answer but not one good solution has become available so far so someone please help or I will have to install Windows on my sons and my girlfriends PCs and that would be a disaster as I am trying to help convince people to move from Windows. I installed 12.04 on three computers on the same day. Dell Inspiron (Works Perfect) Toshiba Satellite Home built Desktop The Dell works perfect but the other two either keep losing connection to the wireless Internet and even when they are connected they stop connecting to web sites, for some reason it searches Google fine but will not connect to web sites when a link is clicked. So far people have recommended in other forums: Removing network manager and installing wicd (didn't solve it) Changing the MTU in the wireless settings (didn't solve it) All sorts of messing about with Firefox settings (this doesn't solve it and even if it did this would leave most average PC users scratching their heads and wishing they had stuck to windows) The problem exists on two very different machines and different wireless cards so I doubt its a driver or hardware issue, also many other Ubuntu users are having the same problem with a vast array of different machines and wireless cards. Can someone please give a good solution to this as its going to turn a lot of people away from Ubuntu if they cannot get this sorted. I would give some PC specs but the two machines are vastly different and the other people complaining of this problem also have very different systems all showing the same problem.

  Read the article

• Strings are UTF-16&hellip;. There is an error in XML document (1, 1).

  - by Shawn Cicoria

  I had a situation today where an xml document had a directive indicating it was utf-8.  So, the code in question was reading in the “string” of that xml then attempting to de-serialize it using an Xsd generated type. What you end up with is an exception indicating that there’s an error in the Xml document at (1,1) or something to that effect. The fix is, run it through a memory stream – which reads the string, but at utf8 bytes – if you have things that fall outside of 8 bit chars, you’ll get an exception.   //Need to read it to bytes, to undo the fact that strings are UTF-16 all the time. //We want it to handle it as UTF8. byte[] bytes = Encoding.UTF8.GetBytes(_myXmlString); TargetType myInstance = null; using (MemoryStream memStream = new MemoryStream(bytes)) { XmlSerializer tokenSerializer = new XmlSerializer(typeof(TargetType)); myInstance = (TargetType)tokenSerializer.Deserialize(memStream); }   Writing is similar – also, adding the default namespace prevents the additional xmlns additions that aren’t necessary:   XmlWriterSettings settings = new XmlWriterSettings() { Encoding = Encoding.UTF8, Indent = true, NewLineOnAttributes = true, }; XmlSerializerNamespaces xmlnsEmpty = new XmlSerializerNamespaces(); xmlnsEmpty.Add("", "http://www.wow.thisworks.com/2010/05"); MemoryStream memStr = new MemoryStream(); using (XmlWriter writer = XmlTextWriter.Create(memStr, settings)) { XmlSerializer tokenSerializer = new XmlSerializer(typeof(TargetType)); tokenSerializer.Serialize(writer, theInstance, xmlnsEmpty); }

  Read the article

• Rails on server syntax error?

  - by Danny McClelland

  Hi Everyone, I am trying to get my rails application running on my web server, but when I run the rake db:migrate I get the following error: r oot@oak [/home/macandco/rails_apps/survey_manager]# rake db:migrate (in /home/macandco/rails_apps/survey_manager) == Baseapp: migrating ======================================================== -- create_table(:settings, {:force=>true}) -> 0.0072s -- create_table(:users) -> 0.0072s -- add_index(:users, :login, {:unique=>true}) -> 0.0097s -- create_table(:profiles) -> 0.0084s -- create_table(:open_id_authentication_associations, {:force=>true}) -> 0.0067s -- create_table(:open_id_authentication_nonces, {:force=>true}) -> 0.0064s -- create_table(:roles) -> 0.0052s -- create_table(:roles_users, {:id=>false}) -> 0.0060s rake aborted! An error has occurred, all later migrations canceled: 555 5.5.2 Syntax error. g9sm2526951gvc.8 Has anyone come across this before? Thanks, Danny Main Migration file c lass Baseapp < ActiveRecord::Migration def self.up # Create Settings Table create_table :settings, :force => true do |t| t.string :label t.string :identifier t.text :description t.string :field_type, :default => 'string' t.text :value t.timestamps end # Create Users Table create_table :users do |t| t.string :login, :limit => 40 t.string :identity_url t.string :name, :limit => 100, :default => '', :null => true t.string :email, :limit => 100 t.string :mobile t.string :signaturenotes t.string :crypted_password, :limit => 40 t.string :salt, :limit => 40 t.string :remember_token, :limit => 40 t.string :activation_code, :limit => 40 t.string :state, :null => :false, :default => 'passive' t.datetime :remember_token_expires_at t.string :password_reset_code, :default => nil t.datetime :activated_at t.datetime :deleted_at t.timestamps end add_index :users, :login, :unique => true # Create Profile Table create_table :profiles do |t| t.references :user t.string :real_name t.string :location t.string :website t.string :mobile t.timestamps end # Create OpenID Tables create_table :open_id_authentication_associations, :force => true do |t| t.integer :issued, :lifetime t.string :handle, :assoc_type t.binary :server_url, :secret end create_table :open_id_authentication_nonces, :force => true do |t| t.integer :timestamp, :null => false t.string :server_url, :null => true t.string :salt, :null => false end create_table :roles do |t| t.column :name, :string end # generate the join table create_table :roles_users, :id => false do |t| t.column :role_id, :integer t.column :user_id, :integer end # Create admin role and user admin_role = Role.create(:name => 'admin') user = User.create do |u| u.login = 'admin' u.password = u.password_confirmation = 'advices' u.email = '[email protected]' end user.register! user.activate! user.roles << admin_role end def self.down # Drop all BaseApp drop_table :settings drop_table :users drop_table :profiles drop_table :open_id_authentication_associations drop_table :open_id_authentication_nonces drop_table :roles drop_table :roles_users end end

  Read the article

• .NET 4.0 Dynamic object used statically?

  - by Kevin Won

  I've gotten quite sick of XML configuration files in .NET and want to replace them with a format that is more sane. Therefore, I'm writing a config file parser for C# applications that will take a custom config file format, parse it, and create a Python source string that I can then execute in C# and use as a static object (yes that's right--I want a static (not the static type dyanamic) object in the end). Here's an example of what my config file looks like: // my custom config file format GlobalName: ExampleApp Properties { ExternalServiceTimeout: "120" } Python { // this allows for straight python code to be added to handle custom config def MyCustomPython: return "cool" } Using ANTLR I've created a Lexer/Parser that will convert this format to a Python script. So assume I have that all right and can take the .config above and run my Lexer/Parser on it to get a Python script out the back (this has the added benefit of giving me a validation tool for my config). By running the resultant script in C# // simplified example of getting the dynamic python object in C# // (not how I really do it) ScriptRuntime py = Python.CreateRuntime(); dynamic conf = py.UseFile("conftest.py"); dynamic t = conf.GetConfTest("test"); I can get a dynamic object that has my configuration settings. I can now get my config file settings in C# by invoking a dynamic method on that object: //C# calling a method on the dynamic python object var timeout = t.GetProperty("ExternalServiceTimeout"); //the config also allows for straight Python scripting (via the Python block) var special = t.MyCustonPython(); of course, I have no type safety here and no intellisense support. I have a dynamic representation of my config file, but I want a static one. I know what my Python object's type is--it is actually newing up in instance of a C# class. But since it's happening in python, it's type is not the C# type, but dynamic instead. What I want to do is then cast the object back to the C# type that I know the object is: // doesn't work--can't cast a dynamic to a static type (nulls out) IConfigSettings staticTypeConfig = t as IConfigSettings Is there any way to figure out how to cast the object to the static type? I'm rather doubtful that there is... so doubtful that I took another approach of which I'm not entirely sure about. I'm wondering if someone has a better way... So here's my current tactic: since I know the type of the python object, I am creating a C# wrapper class: public class ConfigSettings : IConfigSettings that takes in a dynamic object in the ctor: public ConfigSettings(dynamic settings) { this.DynamicProxy = settings; } public dynamic DynamicProxy { get; private set; } Now I have a reference to the Python dynamic object of which I know the type. So I can then just put wrappers around the Python methods that I know are there: // wrapper access to the underlying dynamic object // this makes my dynamic object appear 'static' public string GetSetting(string key) { return this.DynamicProxy.GetProperty(key).ToString(); } Now the dynamic object is accessed through this static proxy and thus can obviously be passed around in the static C# world via interface, etc: // dependency inject the dynamic object around IBusinessLogic logic = new BusinessLogic(IConfigSettings config); This solution has the benefits of all the static typing stuff we know and love while at the same time giving me the option of 'bailing out' to dynamic too: // the DynamicProxy property give direct access to the dynamic object var result = config.DynamicProxy.MyCustomPython(); but, man, this seems rather convoluted way of getting to an object that is a static type in the first place! Since the whole dynamic/static interaction world is new to me, I'm really questioning if my solution is optimal or if I'm missing something (i.e. some way of casting that dynamic object to a known static type) about how to bridge the chasm between these two universes.

  Read the article

• ListView: convertView / holder getting confused

  - by Steve H

  I'm working with a ListView, trying to get the convertView / referenceHolder optimisation to work properly but it's giving me trouble. (This is the system where you store the R.id.xxx pointers in as a tag for each View to avoid having to call findViewById). I have a ListView populated with simple rows of an ImageView and some text, but the ImageView can be formatted either for portrait-sized images (tall and narrow) or landscape-sized images (short and wide). It's adjusting this formatting for each row which isn't working as I had hoped. The basic system is that to begin with, it inflates the layout for each row and sets the ImageView's settings based on the data, and includes an int denoting the orientation in the tag containing the R.id.xxx values. Then when it starts reusing convertViews, it checks this saved orientation against the orientation of the new row. The theory then is that if the orientation is the same, then the ImageView should already be set up correctly. If it isn't, then it sets the parameters for the ImageView as appropriate and updates the tag. However, I found that it was somehow getting confused; sometimes the tag would get out of sync with the orientation of the ImageView. For example, the tag would still say portrait, but the actual ImageView would still be in landscape layout. I couldn't find a pattern to how or when this happened; it wasn't consistent by orientation, position in the list or speed of scrolling. I can solve the problem by simply removing the check about convertView's orientation and simply always set the ImageView's parameters, but that seems to defeat the purpose of this optimisation. Can anyone see what I've done wrong in the code below? static LinearLayout.LayoutParams layoutParams; (...) public View getView(int position, View convertView, ViewGroup parent){ ReferenceHolder holder; if (convertView == null){ convertView = inflater.inflate(R.layout.pick_image_row, null); holder = new ReferenceHolder(); holder.getIdsAndSetTag(convertView, position); if (data[position][ORIENTATION] == LANDSCAPE) { // Layout defaults to portrait settings, so ImageView size needs adjusting. // layoutParams is modified here, with specific values for width, height, margins etc holder.image.setLayoutParams(layoutParams); } holder.orientation = data[position][ORIENTATION]; } else { holder = (ReferenceHolder) convertView.getTag(); if (holder.orientation != data[position][ORIENTATION]){ //This is the key if statement for my question switch (image[position][ORIENTATION]) { case PORTRAIT: // layoutParams is reset to the Portrait settings holder.orientation = data[position][ORIENTATION]; break; case LANDSCAPE: // layoutParams is reset to the Landscape settings holder.orientation = data[position][ORIENTATION]; break; } holder.image.setLayoutParams(layoutParams); } } // and the row's image and text is set here, using holder.image.xxx // and holder.text.xxx return convertView; } static class ReferenceHolder { ImageView image; TextView text; int orientation; void getIdsAndSetTag(View v, int position){ image = (ImageView) v.findViewById(R.id.pickImageImage); text = (TextView) v.findViewById(R.id.pickImageText); orientation = data[position][ORIENTATION]; v.setTag(this); } } Thanks!

  Read the article

< Previous Page | 198 199 200 201 202 203 204 205 206 207 208 209  | Next Page >