Search Results

Search found 14350 results on 574 pages for 'sbs 2008'.

Page 204/574 | < Previous Page | 200 201 202 203 204 205 206 207 208 209 210 211  | Next Page >

  • File server share access intermittent/slow/machine unstable: win2k8r2

    - by Jack B.
    I have a file server running Win2k8R2 on an older HP DL380G4. It has nothing set up on it other than file sharing. All drivers/firmware/updates installed. The file server is used as a dump for a bunch of test machines - so essentially a lot of small files are being written to it. It was working fine until it started showing the following symptoms: Shares became either very slow/intermittent or could not access them at all. Logging in the the server, you could use it like normal but windows would start freezing and eventually you had to hard reboot it because nothing was responsive. After rebooting, it would work fine for 20min-2hours and then degrade into this broken state again. Some info after investigation: HP Raid Config utility shows the Raid array as functioning properly (RAID5 btw). Event log shows a bunch of DoS attacks from the test machines, saying it has disconnected the connection a. AFAIK (not part of my job) the test machines haven't changed the way they log information to this server or the amount of them hasn't increased. b. Nothing is infected, this server was scanned fully, and the test machines are re-imaged almost daily. Nothing in performance monitor shows as anything being pegged at maximum (CPU/HD/Network/RAM) I installed MS Network Monitor and it is showing a lot of traffic The server was using one gigabit Ethernet connection, I connected the second one as well with the same results. Forgot to add - one of the commonly written to dirs on the share has over 16k subdirs in it, with a crapton of small files within those dirs. Some of the OS instability was slow access to the drive which has this directory - perfmon doesn't show much activity on the HD though so I'm not sure if this crowded dir is the cause. Here is one important fact: I ran into this issue 2-3 months ago, couldn't figure it out, but I had a spare identical machine so I swapped them out (thought it was related to the machine), and now I have the same issue. Also, the computer will be stable if I turn off file sharing. So is the server just getting DoS'd by the test machines? I've never dealt with such an issue. Is instability in the server's OS common when getting DoS'd? Is there anything I can do to confirm this before telling the owners of the test machines to optimize their traffic? (I'm not sure what they'll be able to do). Is there something within Win2k8R2 that can balance the traffic across the two NICs? Any help would be appreciated. Update: Another thought - the drive with the share is RAID5 across 6 SCSI320 300GB HDs. They are near full capacity about 100GB from 1TB left. Could the amount of tiny files could be causing some weirdness with the parity in this array? I think I've read something about this in the past but I'm no expert on RAID.

    Read the article

  • SPF blocking some emails. How to complete disable it?

    - by Rafael Colucci
    We have configured a SMTP server on IIS. We have not configured any SPF rule. Some emails are going straight to the badmail folder. Most of them have this error message: Address does not pass the Sender Policy Framework Is there any way to disable that? I know this is insecure and spammers could use it to send spam, but I really need it to be disabled for now until I have configured and tested the SPF correctly.

    Read the article

  • How to export User cert with private key in PKCS12 format

    - by andreas-h
    I'm running Win2008R2, and have installed an Enterprise CA. I can create user certs, but no matter what I do, I cannot export the private key. I'm using the un-touched User certificate template, and the "allow export of private key" option is selected. Still, whenever I go to the "export" dialogue of the certificate (both as user and as administrator), I don't get asked if I want to export the private key, and the option to select PKCS12 format is grayed out. Any help is greatly appreciated!

    Read the article

  • Windows Share permissions

    - by Armando
    I have a SQL/File server that I am replicating a File Share and SQL instance, using ArcServer RHA, to a Replica server. Everything seems to work as far as the replication of the SLQ instance and Share is concerned. When I fail over to the Replica server the DNS Host A record is modified to point to the Replica Server IP Address so if I do an NSLOOKUP on ServerA it then points to the IP Address of ServerB. Ans since the SQL instance is named the same I can still map my ODBC connections to ServerA and I can still make a SQL connection. When I try to do a \ServerA\Share I get an error that says I do not have permissions to the Share. I think this is because it uses keberose authentication and the Share is tied to the actual sever host name. I have tried puting in a CNAME and pointing it to ServerA and Disabling Strict Name Checking on ServerB as well as adding the CNAME to the OptionalNames in the registry but I am still getting the error when I have the ServerA powered off. Is there a way to reset the Authentication of the Share to use the DNS Cname?

    Read the article

  • Windows Server doesn't connect to a network share

    - by Dmitriy N. Laykom
    Windows Server doesn't connect to a network share. Network share is working. Blockquote Pinging 109.123.146.223 with 32 bytes of data: Reply from 109.123.146.223: bytes=32 time<1ms TTL=63 Reply from 109.123.146.223: bytes=32 time<1ms TTL=63 Reply from 109.123.146.223: bytes=32 time<1ms TTL=63 Ping statistics for 109.123.146.223: Packets: Sent = 3, Received = 3, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms net view \shareaddress Blockquote System error 53 has occurred. The network path was not found. When I connected the network share I observed this error message: Blockquote \ "Mapped disk letter" refers to a location that is unavailable. It could be on a hard drive on this computer, or on a network. Check to make sure that the disk is properly inserted, or that you are connected to the Internet or your network, and then try again. If it still cannot be located, the information might have been moved to a different location The network share was mounted via Group Policy. Perchance anyone knows how I can avoid this error? When the OS has been restored from the disk problem has been solved

    Read the article

  • Possible attack on my SQL server?

    - by erizias
    Checking my SQL Server log I see several entries like this: Date: 08-11-2011 11:40:42 Source: Logon Message: Login failed for user 'sa'. Reason: Password did not match for the login provided. [CLIENT: 56.60.156.50] Date: 08-11-2011 11:40:42 Source: Logon Message: Error: 18456. Severity: 14. State: 8. Date: 08-11-2011 11:40:41 Source: Logon Message: Login failed for user 'sa'. Reason: Password did not match for the login provided. [CLIENT: 56.60.156.50] Date: 08-11-2011 11:40:41 Source: Logon Message: Error: 18456. Severity: 14. State: 8. And so on.. Is this a possible attack on my SQL Server from the chineese???! I looked up the IP adress, at ip-lookup.net which stated it was chineese. And what to do? - Block the IP adress in the firewall? - Delete the user sa? And how do I protect my web server the best?! :) Thanks in advance!

    Read the article

  • Active Directory management with low user rights

    - by DemonWareXT
    Our problem: The client, a normal user, has to be able to reset multiple passwords at once. Around 30 in one go. This would call for powershell or something along these lines, but for AD and Powershell one needs to be domain administrator. My solution would be to make a service that runs on the AD server and take connections from a program. The service would then do the AD changes. So far so good, I would just like to hear some other thoughts on this problem. Because I sure can't be the only one with it

    Read the article

  • Windows AD: Is loopback processing absolutely necessary in order to apply a user policy to users logging into computers in the OU?

    - by Brett
    I've had our AD setup running on server 2008r2 and now 2012, and I swear, a user policy applied to an OU containing only computers actually does apply to users logging into those computers, without loopback processing enabled. Everything I read seems to say that is not how it should work, but it does. Is this normal behavior? Just tested again - created a policy with a drive map (which is a user policy), applied it to an OU containing my terminal server, forced a gpupdate, logged out/in, and sure enough, the drive is mapped. I did NOT turn on loopback processing.

    Read the article

  • Bad IIS 7.5 performance on webserver

    - by Robert P.
    I have a webpage (ASP.NET 4.0 / MVC 4). On my development machine (i5-2500 3.3 8GB Win7 VS2010 SP1 Fujitsu Esprimo P700) the page performs with 160 requests/sec on devenv webserver on my machine. The page performs with 250 requests/sec on my local IIS 7.5. (uncompiled web) The page performs with 20 requests per second on a 16core 32gb ram production server (Fujitsu RX-300 w2k8 rc2 IIS 7.5). (compiled web) Why? I think it's the IIS configuration but i can't figure out whats the problem. The page runs with 1 worker process on both machines. Web garden is not an option (it helps but the app isnt compatible with)

    Read the article

  • SQL Connection String to access localhost\SQLEXPRESS

    - by user34683
    I've installed SQL Express on my PC hoping to do some practice creating tables and then modifying them. I coded a webpage in Visual Studio to, basically, SELECT * from a table in the SQLEXPRESS, but I can never get the connection string to work. Please help My connection string "Data Source=localhost\SQLEXPRESS;Initial Catalog=test;User Id=xaa9-PC\xaa9;Password=abcd;" Error Message: Query is select * from tblCustomers where username='johndoe' error is Login failed for user 'xaa9-PC\xaa9'.

    Read the article

  • What could cause a flurry of Microsoft-Windows-Servicing events?

    - by MattUebel
    I have a windows 2k8 machine that generated almost 40,000 WinEventLog:System events in the period of about 20 minutes. The breakdown of these events by eventcode was approximately: 4373 46% 4371 46% 4383 7% 4372 1% Microsoft-Windows-Servicing seemed to go crazy for a short time.... looking at updates, changing the state of updates etc. What could have caused this? UPDATE: Many of the events seem to come in pairs of: Windows Servicing started a process of changing package KBfoobar state from Installed(Installed) to Installed(Installed) and Windows Servicing successfully set package KBfoobar state to Installed(Intstalled)

    Read the article

  • Can't Remote into Windows Server

    - by Brian
    Hello, I have a Dell server wired into the router. I was able to connect to it with my laptop (laptop is wireless) before my router died. My verizon router went kaput, and I got everything else back up and running on the wireless network other than the remoting in feature, even though I can access the server through windows explorer just fine. Any ideas why? What do I need to check? UPDATE: Interesting scenario, Network Discovery is off; I turn it on and save, but for some reason, even after that, network discovery is turning itself off... no idea why that is happening? Thanks.

    Read the article

  • How to change the default domain controller when querying AD in a different site ?

    - by Linefeed
    We have 2 different locations, and at both site we have multiple domain controllers (Win2008). In our application we use Serverless Binding to execute our LDAP queries http://msdn.microsoft.com/en-us/library/ms677945(v=vs.85).aspx. If we look at de DnsHostName of the LDAP://RootDse on site B we always get the default domain controller of site A. Therefor all LDAP queries go much slower. Is there a way to change the default domain controller per site ?

    Read the article

  • Can't Connect SQL server - process being used by another process. Conflict with IIS?

    - by shinya
    I'm having problem connecting to MS SQL Server (2012 Express) after accessing a database through IIS (web site). I can access the data through web site no problem, but I can't access the data from any other programs (i.e SSMS) until I reboot the SQL server. It seems that the connection stays open even if I close a browser. Here is error message I'm getting Unable to open the physical file "C:---------". Operating system error 32: "32(The process cannot access the file because it is being used by another process.)". Unable to open the physical file "C:-------". Operating system error 32: "32(The process cannot access the file because it is being used by another process.)". Cannot open user default database. Login failed. Login failed for user 'Myserver\myname'. (.Net SqlClient Data Provider) Server Name: MYPC\SQLEXPRESS Error Number: 5120 Severity: 16 State: 101 Line Number: 65536 I follow the help link and it told me to move TCP before named pipes in the protocol order list. I tried it but it didn't help at all. What is the proper settings on SQL server or IIS in order to release process after closing a browser. How do I avoid getting this error? Thank you for your help

    Read the article

  • Connecting guest OS to host os internet connection hyper-v

    - by autrevo
    Hyper-V internal switch and VM OS interfacing with Guest OS and IP Cofiguration When configuring hyper-v internal switch, Apart from physical lan adapter (say adapter 1), I see another LAN adapter (say adapter 2) added in host os. And we already have one virtual lan adapter in guest os, (say adapter 3) . adapter 1 is connected to internet with defaulty gateway say, 192.168.0.254 and uses class C IP. By con configuring adapter 2 and 3, I need to acheive two purpose - Access internet in guest os. seemlessly share files & folders between guest and host OS. Please, suggest, What is the best way to configure IP of these three adapters ?

    Read the article

  • Looking for a way to diff many server's filesystem

    - by Itai Ganot
    There's a motivation in my office to make sure that all file systems on all servers in the production environment (It's a Windows environment) are identical until the last file and i'm looking for a program/tool which can help me achieve this goal. What i actually look for is a tool that will allow me to diff server's file systems by connecting them remotely (as they are spreaded around the world). Anyone knows a tool which allows it?

    Read the article

  • What ports do I allow over my internal firewall interface?

    - by blsub6
    I have a Cisco ASA that I have VPN tunnels to connect my internal Windows network. I ran into some trouble logging into my domain so I unblocked all the ports on that internal interface. On a previous question posted here, the general consensus was that I should be blocking ports on my inside interface but my question is: what ports should I unblock? I've tried unblocking ports 88, 139, 135, 389, and 445 and Windows logins still give me problems. Is there some MS documentation somewhere that tells me what I need to unblock to allow Windows logins and other things?

    Read the article

  • Improving Windows Authentication performance on IIS

    - by flalar
    We're struggling with performance issues with a ASP.NET MVC site that is using Windows Authentication. Response time is very slow on the first request to the site when the user is being authenticated. Further, every time the Authorization header is sent from the browser the response time increases with many seconds. The same issue occurs for both executed files and static content like CSS and JS. Access to the application is restricted to users within a certain role and we are now planning to allow access to static files for all authenticated users to see if that helps. The authentication method in use is NTLM. How should we go forward in pinpointing why authentication decreases performance drastically?

    Read the article

  • Cannot access folder locally, but can remotely

    - by Cylindric
    I'm having a peculiar problem on one of my servers at the moment, which seems to be related to authentication in some way, but I have no idea how to find the root of the problem. I have a folder on the server D:\Somefolder\Logs. If I am connected to the server via an RDP terminal, so essentially "local", I cannot access that folder - I get an access denied. If I am connecting from my machine to it using the share \server\d$\Somefolder\Logs, I can access it. I'm logging in to both machines as the same user. Permissions on the folder seem quite simple, CREATOR OWNER, SYSTEM and Administrators. I am a Domain Admin, and they are in the local "Administrators" group. It is also affecting things like access to SQL Server, so I don't think it's a simple folder-permissions thing. For example, I cannot connect SQL Management Studio to all the local SQL instances using a domain account, but I can if I connect remotely to it.

    Read the article

  • Accessing C$ over LAN on Win2008R2 - cannot by hostname but can by IP and FQDN

    - by Idgoo
    Having an issue with one of our Win2k8 R2 file servers. Trying to access C$ or the Admin share is giving us an error (see error details that the bottom), however we are able to connect using the server's IP and FQDN. can access \\172.16.x.x\c$ with domain cred can access \\server.domain.local\c$ with domain creds cannot access \\servername\c$ with same domain creds Server pings fine with Hostname, IP, FQDN, the Primary DNS suffix is also correct. DNS, PTR and Wins records are all correct for the Server I have checked that I am not trying to connect with cached credentials in the Windows vault, the server is also appending primary and connection specific DNS suffixes to the hostname. Any ideas what might be causing this issue? Error Details: c$ is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions

    Read the article

  • HP p410i array controller - what happens if i add memory?

    - by James
    I have a p410i array controller that only has 256ram. We want to create a raid 5 so we have procured a 512 write back cache module. If we install the write back cache, will this erase the existing raid information. The server currently has 2 disks in raid 1. 6 are spare waiting for an upgrade to create a raid 5. the concern is if we replace/upgrade the memory for the controller, we will wipe the existing production raid 1 array. Thanks in advance.

    Read the article

  • Why can't service account such as Local Service, Network Service, or Local System be managed on a domain level?

    - by smwikipedia
    Hi security experts, I read from here that: On a local computer, an administrator can configure the application to run as Local Service, Network Service, or Local System. These service accounts are simple to configure and use but are typically shared among multiple applications and services and cannot be managed on a domain level. I just don't understand why these accounts cannot be managed on a domain level, since they all have well-known SIDs? Thanks for your time.

    Read the article

  • What happens when a snapshot is deleted

    - by Ralph Shillington
    I have a tree of snapshots taken about once an hour as I progressed through a rather tricky server setup. Now that I'm done, I would like to get rid of the snapshots, but I gather that these are actually differencing drives. If that's the case, does it not mean that deleting a snapshot will in fact revert me back to a previous point in time. Or does it mean that deleting a snapshot merges the changed bits into the parent VHD.

    Read the article

< Previous Page | 200 201 202 203 204 205 206 207 208 209 210 211  | Next Page >