Search Results

Search found 19958 results on 799 pages for 'bit fiddling'.

Page 205/799 | < Previous Page | 201 202 203 204 205 206 207 208 209 210 211 212  | Next Page >

  • Video memory buswidth vs video memory Bandwidth

    - by Mixxiphoid
    My current video card (9600GT) is dying and I'm searching for a new video card. Between acquiring my current one and now, I got a lot more knowledge about hardware and I want to use that to pick my new card. So I decided to not just buy some popular card blindly, but to search for a card able to handle my hardware requirements. I searched the specs at the NVidia site for the GT640 and was confused by the memory section and some questions raised. My current card's memory bus width is 256bit and has 1GB of memory. I checked Google about the importance of bus width. And all the links basically said the same 'The higher the number the more potential simultaneously traffic can be transferred'. This was already clear to me, yet there are currently a lot of new cards which are considered better than my current one with a lower bus width. To go in more detail about my question I copied the memory info from the NVidia site: GT 640 GT640 GDDR5 Memory Specs: Memory Clock 1.8 Gbps 5.0 Gbps Standard Memory Config 2048 MB 1024 MB Memory Interface DDR3 GDDR5 Memory Interface Width 128-bit 64-bit Memory Bandwidth (GB/sec) 28.5 40.0 What puzzled me is that the Memory Bandwidth seems to me the most important part, yet the lower bus width has the higher 'performance'. Is this due to the fact the memory interface is GDDR5 and is therefore able to have a higher memory clock speed (5Gbps)? If I am to buy a new video card, should I check the bus width? Memory clock? Bandwith? Amount of memory? My current card ahs 1GB memory, so I was searching for a 2GB memory card, but now I'm not so sure any more whether that is really 'better'. My main question: To me it seems that memory performance is made up by the combination of bus width and frequency. Is this true? If yes, why are there so many sites telling me I need to get a card with a high bus width? If no, then what IS important when it goes about memory performance on a video card. NOTE: The memory bandwidth is (almost) never displayed on vendor sites. How can I determine which card is better without knowing the bandwith?

    Read the article

  • Migrate IMAP account between providers - client access only

    - by Pekka
    I have an IMAP E-Mail account with my old provider. I have a new, empty IMAP account with the new provider. Is there a tool or Thunderbird to migrate the E-Mail data from one account to another? I'm a bit wary about just doing a drag & drop in Thunderbird because it's quite a lot of data, and I have a deep distrust against how Thunderbird deals with IMAP data.

    Read the article

  • How do I delete the next line in vim?

    - by Jason Baker
    In emacs, whenever I want to delete a few lines of text, I just use C-k until all the text is gone. However, in vim it seems a bit more complex. I know I can do d$ to delete until the end of the line and dd to delete the entire line I'm on, but how do I delete all of the next line?

    Read the article

  • Hardware purchase recommendation

    - by Maxim Veksler
    I'm building a custom PC configuration for Development / Gaming. I know hardware but I'm not an expert. It would be great if I could post my hardware list and get some review & recommendation for the hardware selections I've made. Do you know of any website / forum that does that? Thank you, Maxim. p.s. To whom it may concern, the work in progress hardware list is here http://bit.ly/9zBU2y

    Read the article

  • utorrent does not work with proxy server

    - by developer
    I have utorrent 3.2.2(build 28500) 32-bit. I am trying to download torrent using a proxy server but nothing is working. It shows that you have a wrong network configuration. But the same server settings is working for Google chrome and Internet Download Manager. How to do it ? Also one questions: Any way to convert torrent to direct download other than zbigz.com, torrific.com and torcache.com ( i tried them, not working)?

    Read the article

  • Remote Desktop 7 XP -> Windows 7

    - by Michael
    I am running Windows 7 at my office and Windows XP at home. I have seen the new Remote Desktop and want to use (I have three monitors at office and three at home) In the specs I saw where in order to use the multimon features you must connect to a Windows 7 client (I am running Windows 7 Professional 64-bit in my office) When I connect to it (from XP running RDP 7) I can't get all my monitors to come up, just one Is there something I am doing wrong? Both are running the same version of RDP Thanks for any help

    Read the article

  • Host timeout during file upload/download over SFTP/SSH

    - by kritop
    I tried different clients because i thought its client related, but all of them sooner or later disconnect or stop uploading/downloading files, and getting a timeout disconnect. After a reconnect it works again for a bit of time. Really strange cannot figure out the reason. I'm on a mac and the server is a debian VPS! If u need further informations ask please! I appreciate any tips, because i'm kinda stuck!

    Read the article

  • When to use a RAM-Disk?

    - by Ice
    Hi, I know that RAM-Disk are fast, faster than any Disk but they lose their contents on a shutdown of the operating system. The capacity is limited to the RAM. Is there a usefull implementation on a new 64-Bit windows 2008 server? Peace Ice

    Read the article

  • Apache subdomain problem

    - by Rudiger
    Sorry if this is answered somewhere else but can't figure it out. Cant get my server to respond on the subdomain, only the main domain. Relevant info below, if you need more let me know. Listen 10.0.1.191:80 ServerName server.local:80 (i know a bit stupid but logical for me and it works) ServerName www.server.local ServerAlias server.local DocumentRoot /var/www/html/ ServerName qtp.server.local DocumentRoot /var/www/qtp/ Cheers

    Read the article

  • Does the DisplayPort on the Dell UltraSharp U2311H Monitor work with a MacBook Pro?

    - by GeneQ
    I'm thinking of getting the Dell UltraSharp U2311H monitor which apparently comes with a DisplayPort. (I used the word "apparently" because I find DisplayPort support a little bit too good to be true, coming from Dell. But great news nonetheless if it's really true) I plan to connect it to a Mac Book Pro (2010) via a mini DisplayPort to DisplayPort cable. Has anyone tried this setup? Does it work? Thanks.

    Read the article

  • What is the best bang for buck desktop CPU

    - by dev5
    What is the best bang for buck desktop cpu available at the moment. AMD or Intel are both OK. Although slight bias to AMD since i prefer their motherboards. It's for an all round machine, i do a bit of everything, from gaming to web development.

    Read the article

  • Legacy VB6 application under Win7 SQL error

    - by Shial
    We have a rather unfortunate legacy application at work, written originally in VB6 it predates anybody in our IT department by at least 5 years. We have a contracted developer for ongoing maintenance and where he can he rewrites sections over into .NET code (Not sure about his techniques here, this is a side job for his regular work as an IBM engineer) the application works fine (such as it is) under windows XP. We have only a couple of Windows 7 machines mainly for testing and this application seems to run into a wall. Things like the background not loading and SQL errors. This is even running under administrator. Running an SQL trace from the ODBC control panel shows several interesting things. It makes a connection to the database successfully initially where it runs a query to determine if it is running the correct version. This query works fine. 558-1af0 ENTER SQLExecDirectW HSTMT 0x020D7548 WCHAR * 0x04C8F0F0 [ 115] "SELECT count(*) c FROM tblSoftwareVersion WHERE fldSoftwareVersion = '123456' AND fldSoftwareName = 'Application.VB'" SDWORD 115 BMS 558-1af0 EXIT SQLExecDirectW with return code 1 (SQL_SUCCESS_WITH_INFO) HSTMT 0x020D7548 WCHAR * 0x04C8F0F0 [ 115] "SELECT count(*) c FROM tblSoftwareVersion WHERE fldSoftwareVersion = '123456' AND fldSoftwareName = 'Application.VB'" SDWORD 115 It then seems to drop its connection and can't find the ODBC connection despite the fact its connecting to the same DB. From the trace it looks like it configures the connection then it starts firing off SQLFreeStmt to unbind and close out then when in the application and it tries to do its thing there is no connection. 558-1af0 ENTER SQLFreeStmt HSTMT 0x020D7548 UWORD 2 <SQL_UNBIND> BMS 558-1af0 EXIT SQLFreeStmt with return code 0 (SQL_SUCCESS) HSTMT 0x020D7548 UWORD 2 <SQL_UNBIND> Then this happens when I try to do something that pulls data 558-1af0 ENTER SQLDriverConnectW HDBC 0x020DDA00 HWND 0x00000000 WCHAR * 0x73EF8634 [ -3] "******\ 0" SWORD -3 WCHAR * 0x73EF8634 SWORD -3 SWORD * 0x00000000 UWORD 0 <SQL_DRIVER_NOPROMPT> BMS 558-1af0 EXIT SQLDriverConnectW with return code -1 (SQL_ERROR) HDBC 0x020DDA00 HWND 0x00000000 WCHAR * 0x73EF8634 [ -3] "******\ 0" SWORD -3 WCHAR * 0x73EF8634 SWORD -3 SWORD * 0x00000000 UWORD 0 <SQL_DRIVER_NOPROMPT> DIAG [IM002] [Microsoft][ODBC Driver Manager] Data source name not found and no default driver specified (0) Nearly all of my searching on this issue comes up with programming issues where the connection string has a problem. The only thing that is different in this particular scenario though is Windows 7, I know the connection string is fine since it works on the XP machines. The VB components are supposed to be still functional under Win7. My computer is running 32 bit win7 and my VP is running Win7 64 bit and both have the same problem so that can be ruled out. I have already tried reinstalling the SQL Native Client and the VB runtime as well as the application in question. Hopefully I can find a solution and not have to resort to using the XP VM.

    Read the article

  • External USB HD issues with a twist (works on Windows7 but not XP)

    - by Eruditass
    I have this older external USB HD, 160 GB. I was using it to copy my Steam games to another computer. On the source computer, Windows 7 64-bit, everything worked fine. Drive reported no errors, had no hiccups, etc. Plugging it into the Windows XP 32-bit computer, it worked fine for looking through the files, moving files around on it (no real reading/writing, just modifying the filesystem table). However, when copying files from it to my internal HD, after a couple seconds to tens of minutes (seemingly random times), the USB device becomes unrecognized and it reports a delayed write error. Events in system log go like this, chronologically: (number times displayed)xSource (Event ID): "message" 2xdisk (51): An error was detected on device \Device\Harddisk1\D during a paging operation. 1xftdisk (57): The system failed to flush data to the transaction log. Corruption may occur. 1xApplication popup (26): Windows - Delayed Write Failed : Windows was unable to save all the data for the file E:\$Mft. The data has been lost. This error may be caused by a failure of your computer hardware or network connection. Please try to save this file elsewhere. 1xntfs (50): {Delayed Write Failed} Windows was unable to save all the data for the file . The data has been lost. This error may be caused by a failure of your computer hardware or network connection. Please try to save this file elsewhere. These repeat for a while, then there is 10+ disk messages or ftdisk messages. Other notes: This occurs on random files at random times. This problem cannot be replicated on the Windows 7 source machine when copying from the HD to a different location on its local disk chkdsk /f was run and found no errors. chkdsk /f/r has the delayed write issue. drive was set to quick removal. Setting to performance in device manager yielded same result I am not writing anything to the USB external drive, so I am not sure why there is even a delayed write error (writing file access times?) local Windows XP was chkdsk'd without problems Windows XP machine has no problems with other USB HD's Various USB ports were attempted Rebooting did not help Occurs with SyncToy as well as windows explorer SMART status is good on both local drive and the external one Lack of gaming is making me cranky

    Read the article

  • Windows 7 XP Mode, Resizing triggering lock

    - by greggorob64
    I'm a developer using Windows 7 XP Mode to get some old 16-bit apps to run. A hugely annoying hurtle I'm encountering is this: When I resize my XP windows at all (usually by mistake), it automatically logs me off (or Locks), requiring me to log in. This causes my build batch file to stop, which is potentially hours of work lost. Any help would be appreciated, thanks.

    Read the article

  • How to stop switchable graphics from switching to high-power GPU when charging the laptop?

    - by Saifallah
    I've an Acer laptop with Windows 7 64 bit and an ATI Radeon HD 6550M Graphics card. Whenever I connect the power to charge the battery it automatically switches to the high-power GPU (ATI) instead of the low-power (Intel) GPU. There's an option in the bios to stop such thing but it makes the GPU runs always on high-power and I can't switch to the low-power GPU. How can I prevent the switchable graphics from automatically using the high-power GPU when charging?

    Read the article

  • Debian - error while loading shared libraries

    - by Jirí Valoušek
    i have an problem with script DocToText from Silvercoders.com on my 64bit Debian Squeeze. It works properly on another 32bit machine, but on this i have still problem with some .so module. # file /bin/bash /bin/bash: ELF 64-bit LSB executable, x86-64, version 1 (SYSV), dynamically linked (uses shared libs), for GNU/Linux 2.6.18, stripped if i run doctotext.sh it`s return an error: ./doctotext: error while loading shared libraries: libgsf-1.so.114: cannot open shared object file: No such file or directory please, can you help?

    Read the article

  • How do I profile the startup process in OS X 10.5?

    - by Alex Mcp
    When I bought my MBP 2.2 GHZ in 2007, it got from dead to an active dock in about 18 seconds, and now it takes about 1:30 to get a fully responsive home screen. I want to find a way to profile the various things it does when it starts up so I can begin tuning it a bit. Any good software or other recommendations for this process?

    Read the article

  • Gmail rejects emails. Openspf.net fails the tests

    - by pablomedok
    I've got a problem with Gmail. It started after one of our trojan infected PCs sent spam for one day from our IP address. We've fixed the problem, but we got into 3 black lists. We've fixed that, too. But still every time we send an email to Gmail the message is rejected: So I've checked Google Bulk Sender's guide once again and found an error in our SPF record and fixed it. Google says everything should become fine after some time, but this doesn't happen. 3 weeks already passed but we still can't send emails to Gmail. Our MX setup is a bit complex, but not too much: We have a domain name delo-company.com, it has it's own mail @delo-company.com (this one is fine, but the problems are with sub-domain name corp.delo-company.com). Delo-company.com domain has several DNS records for the subdomain: corp A 82.209.198.147 corp MX 20 corp.delo-company.com corp.delo-company.com TXT "v=spf1 ip4:82.209.198.147 ~all" (I set ~all for testing purposes only, it was -all before that) These records are for our corporate Exchange 2003 server at 82.209.198.147. Its LAN name is s2.corp.delo-company.com so its HELO/EHLO greetings are also s2.corp.delo-company.com. To pass EHLO check we've also created some records in delo-company.com's DNS: s2.corp A 82.209.198.147 s2.corp.delo-company.com TXT "v=spf1 ip4:82.209.198.147 ~all" As I understand SPF verifications should be passed in this way: Out server s2 connects to MX of the recepient (Rcp.MX): EHLO s2.corp.delo-company.com Rcp.MX says Ok, and makes SPF check of HELO/EHLO. It does NSlookup for s2.corp.delo-company.com and gets the above DNS-records. TXT records says that s2.corp.delo-company.com should be only from IP 82.209.198.147. So it should be passed. Then our s2 server says RCPT FROM: Rcp.MX` server checks it, too. The values are the same so they should also be positive. Maybe there is also a rDNS check, but I'm not sure what is checked HELO or RCPT FROM. Our PTR record for 82.209.198.147 is: 147.198.209.82.in-addr.arpa. 86400 IN PTR s2.corp.delo-company.com. To me everything looks fine, but anyway all emails are rejected by Gmail. So, I've checked MXtoolbox.com - it says everything is fine, I passed http://www.kitterman.com/spf/validate.html Python check, I did 25port.com email test. It's fine, too: Return-Path: <[email protected]> Received: from s2.corp.delo-company.com (82.209.198.147) by verifier.port25.com id ha45na11u9cs for <[email protected]>; Fri, 2 Mar 2012 13:03:21 -0500 (envelope-from <[email protected]>) Authentication-Results: verifier.port25.com; spf=pass [email protected] Authentication-Results: verifier.port25.com; domainkeys=neutral (message not signed) [email protected] Authentication-Results: verifier.port25.com; dkim=neutral (message not signed) Authentication-Results: verifier.port25.com; sender-id=pass [email protected] Content-class: urn:content-classes:message MIME-Version: 1.0 Content-Type: multipart/alternative; boundary="----_=_NextPart_001_01CCF89E.BE02A069" Subject: test Date: Fri, 2 Mar 2012 21:03:15 +0300 X-MimeOLE: Produced By Microsoft Exchange V6.5 Message-ID: <[email protected]> X-MS-Has-Attach: X-MS-TNEF-Correlator: Thread-Topic: test Thread-Index: Acz4jS34oznvbyFQR4S5rXsNQFvTdg== From: =?koi8-r?B?89XQ0tXOwMsg8MHXxcw=?= <[email protected]> To: <[email protected]> I also checked with [email protected], but it FAILs all the time, no matter which SPF records I make: <s2.corp.delo-company.com #5.7.1 smtp;550 5.7.1 <[email protected]>: Recipient address rejected: SPF Tests: Mail-From Result="softfail": Mail From="[email protected]" HELO name="s2.corp.delo-company.com" HELO Result="softfail" Remote IP="82.209.198.147"> I've filled Gmail form twice, but nothing happens. We do not send spam, only emails for our clients. 2 or 3 times we did mass emails (like New Year Greetings and sales promos) from corp.delo-company.com addresses, but they where all complying to Gmail Bulk Sender's Guide (I mean SPF, Open Relays, Precedence: Bulk and Unsubscribe tags). So, this should be not a problem. Please, help me. What am I doing wrong? UPD: I also tried Unlocktheinbox.com test and the server also fails this test. Here is the result: http://bit.ly/wYr39h . Here is one more http://bit.ly/ypWLjr I also tried to send email from that server manually via telnet and everything is fine. Here is what I type: 220 mx.google.com ESMTP g15si4811326anb.170 HELO s2.corp.delo-company.com 250 mx.google.com at your service MAIL FROM: <[email protected]> 250 2.1.0 OK g15si4811326anb.170 RCPT TO: <[email protected]> 250 2.1.5 OK g15si4811326anb.170 DATA 354 Go ahead g15si4811326anb.170 From: [email protected] To: Pavel <[email protected]> Subject: Test 28 This is telnet test . 250 2.0.0 OK 1330795021 g15si4811326anb.170 QUIT 221 2.0.0 closing connection g15si4811326anb.170 And this is what I get: Delivered-To: [email protected] Received: by 10.227.132.73 with SMTP id a9csp96864wbt; Sat, 3 Mar 2012 09:17:02 -0800 (PST) Received: by 10.101.128.12 with SMTP id f12mr4837125ann.49.1330795021572; Sat, 03 Mar 2012 09:17:01 -0800 (PST) Return-Path: <[email protected]> Received: from s2.corp.delo-company.com (s2.corp.delo-company.com. [82.209.198.147]) by mx.google.com with SMTP id g15si4811326anb.170.2012.03.03.09.15.59; Sat, 03 Mar 2012 09:17:00 -0800 (PST) Received-SPF: pass (google.com: domain of [email protected] designates 82.209.198.147 as permitted sender) client-ip=82.209.198.147; Authentication-Results: mx.google.com; spf=pass (google.com: domain of [email protected] designates 82.209.198.147 as permitted sender) [email protected] Date: Sat, 03 Mar 2012 09:17:00 -0800 (PST) Message-Id: <[email protected]> From: [email protected] To: Pavel <[email protected]> Subject: Test 28 This is telnet test

    Read the article

  • Apple: Airport extreme, 3 questions

    - by Patrick
    1) Can I use airport extreme + external hard disk as a server ? I mean, can I run operating systems such as ubuntu on it ? 2) Is it a bit noisy ? Can I place it in my sleeping room ? 3) Can airport extreme expand networks ? On the Apple website they say only Time Capsule can do it: www.apple.com/wifi/ thanks

    Read the article

  • How can I change the handwriting input language in Windows 7?

    - by askvictor
    I'm in a school where all students have tablet PCs, where they use the handwriting (text recognition) function quite a bit. Recently one of the language teachers has asked if they can enter French accents using this method - it seems that one definitely can using windows 7 ultimate, but we're using Pro. I understand that if one changes the entire input language, then this should work, but it doesn't seem to. Any ideas?

    Read the article

< Previous Page | 201 202 203 204 205 206 207 208 209 210 211 212  | Next Page >