Search Results

Search found 6463 results on 259 pages for 'flash cs6'.

Page 206/259 | < Previous Page | 202 203 204 205 206 207 208 209 210 211 212 213  | Next Page >

  • update ocz vertex le capacity via firmware update

    - by Ben Voigt
    I have an OCZ Vertex LE 100GB drive. It's actually 128GiB of NAND flash, with a whopping 28%+ reserved for write combining. Most 128GiB drives are actually ~ 115GB usable (and marketed as 120GB or 128GB). There were rumors that the reserved fraction could be decreased on OCZ 100GB drives. Can anyone provide a link to firmware that does that, or an official statement that no such firmware exists? (NB: I recently installed the 1.24 firmware from the OCZ site, it didn't affect the capacity. Possibly because the rumors say the capacity change is destructive to existing content.) Of possible interest: flashing firmware was more of a pain than it should have been -- the tool didn't detect the disk until I booted an older Windows install off a secondary hard disk, I suspect the Intel SATA driver is the issue and tool only works with the msachi.sys driver.

    Read the article

  • Windows 8.1 installation: Which drive is the F drive?

    - by sammyg
    I am doing a clean install of Windows 8.1 on an old PC. It was purchased as download from Microsoft Store and written to and booted from a USB flash drive. It went through all of these steps: Copying Windows Files Getting files ready for installation Installing features Installing updates Then at "Getting finished" I am stuck at this stupid dialog box. Please unplug the following external drive and click OK to restart your computer and finish installing Windows. F: How do I tell what physical drive this is? Can I drop to command prompt during installation? And is it safe to unplug it while powered on? There is no external hard drive connected, none that I can see. There is no USB or FireWire drive connected externally. I think it sees one of the internal drives as external... in some weird way?!

    Read the article

  • Unable to browse some pdfs and docs.

    - by JamesEggers
    I have a web site that uses Microsoft Indexing Service to index and query a directory that holds various documents of type pdf, rtf, mht, and doc. The indexing and querying works well (for the most part); however, some files will load while others will not. This is a Windows Server 2003 box running the site using IIS 6. The indexed directory is a sub directory off of the site's root directory (i.e. http://my.domain.com/files/). The file paths are accurate in the URL; however, I can only access some of the files of each file type. The files that I cannot access give a 404 File Not Found. I am able to open all files via windows explorer;however, attempting to open them via a browser over http is hit and miss. Has anyone experienced this issue and know how to resolve it? Anyone have any idea why I could access some files but not others? Does anyone have any recommendations on what to look into to try this (i.e. does owner matter or something like that?)? EDIT: Here is the Request and Response Headers for a bad file: GET /files/file1.pdf HTTP/1.1 Accept: image/gif, image/jpeg, image/pjpeg, image/pjpeg, application/x-shockwave-flash, application/xaml+xml, application/vnd.ms-xpsdocument, application/x-ms-xbap, application/x-ms-application, application/x-silverlight, application/vnd.ms-excel, application/vnd.ms-powerpoint, application/msword, / Accept-Language: en-us User-Agent: Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 5.1; Trident/4.0; .NET CLR 1.1.4322; .NET CLR 2.0.50727; .NET CLR 3.0.04506.30; .NET CLR 3.0.04506.590; .NET CLR 3.0.04506.648; .NET CLR 3.5.21022; .NET CLR 3.0.4506.2152; .NET CLR 3.5.30729) Accept-Encoding: gzip, deflate Proxy-Connection: Keep-Alive Host: my.domain.com HTTP/1.1 404 Not Found Content-Length: 1635 Content-Type: text/html Server: Microsoft-IIS/6.0 X-Powered-By: ASP.NET Date: Mon, 01 Jun 2009 15:38:54 GMT [typical 404 page markup excluded] Here is the Request/Response headers for the good file: GET /files/file2.pdf HTTP/1.1 Accept: image/gif, image/jpeg, image/pjpeg, image/pjpeg, application/x-shockwave-flash, application/xaml+xml, application/vnd.ms-xpsdocument, application/x-ms-xbap, application/x-ms-application, application/x-silverlight, application/vnd.ms-excel, application/vnd.ms-powerpoint, application/msword, / Accept-Language: en-us User-Agent: Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 5.1; Trident/4.0; .NET CLR 1.1.4322; .NET CLR 2.0.50727; .NET CLR 3.0.04506.30; .NET CLR 3.0.04506.590; .NET CLR 3.0.04506.648; .NET CLR 3.5.21022; .NET CLR 3.0.4506.2152; .NET CLR 3.5.30729) Accept-Encoding: gzip, deflate Proxy-Connection: Keep-Alive Host: my.domain.com HTTP/1.1 200 OK Content-Length: 352464 Content-Type: application/pdf Last-Modified: Tue, 13 Jan 2009 15:27:35 GMT Accept-Ranges: bytes ETag: "74ccc5759375c91:2a47" Server: Microsoft-IIS/6.0 X-Powered-By: ASP.NET Date: Mon, 01 Jun 2009 15:50:33 GMT

    Read the article

  • No sounds played in google chrome tabs

    - by shtolik
    I have somehow muted all the tabs in my google chrome. Youtube and other flash players are playing video, but there is no sound. In Window 7 Volume mixer I can see Google chrome icon and it has muted icon there. But clicking that icon unmute sounds just for a second and then it's muted back on. Seems that chrome itself or some of it extensions are turning mute... Update: How do I mute certain tabs in Chrome? question seems related, but I don't have MuteTab extension installed in Chrome.

    Read the article

  • create replica of ext4 filesystem and re-use it

    - by Jatin
    Is there a way that I can use my Linux ext4 file system, as such and then use it on some other computer. I have a dual-boot of Windows 7 and Ubuntu 10.04 and my partition table looks like this: My question might not be clear, so explaining it with an example. Can I copy my Linux partition on a flash drive and then use it on a different PC, with or without any need to install Ubuntu on new PC, by simply booting from the copied ext4 partition. This way, I can easily port my Ubuntu packages and other applications, settings etc. from one PC to other. If it's a very stupid question, please don't mind.

    Read the article

  • How to get access to console to reset Cisco 3750?

    - by genehack
    I acquired two Cisco 3750 switches from another part of my organization. I was able to complete the standard password/config reset procedure on one without any issues -- boot it, put it into express config mode, telnet in, reset the passwords, etc. The second one doesn't ever boot to the point where it displays anything on the console. When power cycled, the 'SYST' light flashes green a few times, then comes on a solid green and stays lit. None of the other lights ever flash or light up. Holding down the 'MODE' button for up to 30 seconds produces no noticeable effects. Nothing ever comes out on the console. Since I was able to configure the first one without any problems, I know my connectinon is good -- console port configured right, good cable, etc. Is this just a hardware problem with the switch? Is there any way I can recover from this and get the switch back into a state where I can configure it?

    Read the article

  • Best Small Linux Distribution for rDesktop

    - by d2jxp
    What would be the best linux distribution to use just for the purpose of rDesktop? We're trying to decide if we should get rid of old computers or just use them as thin-clients to connect to virtual Windows 7 machines on our network. I would like something with as little bloat as possible and can be run from a USB flash drive. I have tried SliTaz, ThinStation, and Pixil from Century Software. SliTaz has been my favorite so far but I still want to know if there's something better that's also easily customizable.

    Read the article

  • mount dev, proc, sys in a chroot environment?

    - by Patrick
    I'm trying to create a Linux image with custom picked packages. I followed the guide here http://www.olpcnews.com/forum/index.php?topic=4766.0 However, when I tried to install some packages, it failed to configure due to missing the proc, sys, dev directories. So, I learned from other places that I need to "mount" the host proc, ... directories to my chroot environment. Though, I saw two syntax and am not sure which one to use. In host machine: mount --bind /proc <chroot dir>/proc and another syntax (in chroot envrionment): mount -t proc none /proc Which one should I use, and what are the difference? Edit: What I'm trying to do is to hand craft the packages I'm going to use on an XO laptop, because compiling packages takes really long time on the real XO hardware, if I can build all the packages I need and just flash the image to the XO, I can save time and space.

    Read the article

  • Ubuntu 9.10 LiveCD stalls after "Install Ubuntu" selected from boot menu on eMachines

    - by nicorellius
    I am trying to install Ubuntu 9.10 from the ISO on a CD (it needs to be this version) on an eMachine with a brand new Seagate hard disk. The CD boots OK, and I choose the language. Then I am presented with the boot menu: Try Ubuntu Install Ubuntu etc I have tried the top two choices several times (trying Ubuntu and installing it), but each and every time the installation stalls and the disc stops spinning right after I hit enter after choosing the option I want. I have tried different CD/DVD drives, changing the jumpers on both CD drives, different hard drives, and nothing works. Maybe there is a BIOS setting that is choking the installation? Any help would be appreciated. Edit - I just tried running the hard drive as the master on the primary IDE and the CD drive as the slave on the primary with the same results. Maybe flash the BIOS?

    Read the article

  • Extract MP3 URL from a SWF file

    - by Charles
    I have a SWF file that basically shows a streamer, and it plays a song (I'm guessing it's MP3) that it links to, somewhere. I know the audio isn't embedded in the file since the SWF's file size is ~370KB. With most flash FLV and MP3 players, Internet Download Manager catches the URL as soon as the video/audio starts to load, and I can easily download it using IDM. In this case, IDM doesn't seem to sense anything - so I thought maybe I could extract the MP3 location myself. I tried decompiling the SWF file, as I'd heard before that with some files, decompiling can help in breaking down a file and getting just the info you need - but I honestly don't know what to look for in this particular file. Suggestions?

    Read the article

  • Which free IMAP-supporting webmail would you recommend?

    - by Razor
    Considering a machine with IIS 7.5/PHP 5.2/asp.net and mysql/MSSQL available, which webmail would you pick? Don't think it's relevant but the mail server is installed on localhost, and is hmailserver. If it's one using asp.net it'd be a bonus, but PHP is ok as well and probably offers more choices. "Client side" look and feel definitely needed, flash/silverlight/ajax not a problem. I have also seen this question, but being asked almost 2years ago and being focused on php webmails, I thought that some better option could've been released in the meantime.

    Read the article

  • Joomla 1.5 Media Manager sets incorrect file permissions when uploading

    - by Scott Mayfield
    Howdy all, I have a Joomla 1.5 installation running on Windows Server 2008, installed via the Web Platform Installer. When uploading images with the media manager (native uploader, not the flash bulk uploader), the files arrive on the server correctly, but are given incorrect permissions. Specifically, the IIS_IUSRS group is not given access to the file. I might be incorrect about what group/user is SUPPOSED to get access to the files, but so far, I've found that unless I give IIS_IUSRS access to the uploaded files, they won't appear on the site or in the media manager (appear as broken images). Once I give IIS_IUSRS permission to the files, they work fine. So far, all the research I've done has led me to linux specific fixes that involve either changing the umask on the server, or directly modifying the Joomla codebase to add an appropriate chmod command to the upload process, but I really don't want to modify Joomla directly. I have to believe there's a setting here somewhere that will do the job, either on the Joomla or Windows side of the equation. Any thoughts? Scott

    Read the article

  • Is there a way to submit a batch of commands to a Cisco router and have them execute from the router?

    - by atroon
    I need to change the configuration of a remote (6 hours' drive) client's Cisco 871 (IOS 12.4.15T) from my location because of some new internet service at his location. To be more precise, I need to change the default route, ip address of the outside interface (Fa4) and disable the PPPoE setup there. Unfortunately, doing any of this will (obviously) break the connection to the router. I do not have an out-of-band management modem set up (I know, I know). Is there any way to enter the commands I need to have run and have them execute one after the other, from a file on flash:? I have never tried anything like that before. Essentially a DOS-style batch file is exactly what I need. Nothing like it seems to be out there except using kron to execute CLI commands, but that is specified here as only taking EXEC commands, not configuration ones. Is there hope, or do I travel?

    Read the article

  • Older raid controllers in raid 5 vs. Jbod and SW raid

    - by TEB
    Hi. Im in the fortunate position to have 6 Supermicro older VOD servers with the following config: Supermicro 3U case, 3xPSU Dual Xeon 3ghz P4 class cpu (5 years old.. havnt checked the exact type) 4GB Ram 3ware 9500-8 SATA controller 8 SATA SLOTS and alot of free drives. 2GB FLASH Bootdrive What im curious about is the RAID5 performance on these old beasts in HW mode vs. SW on Linux with the controller set in JBOD mode. Im thinking on using Centos 5.5 or Ubuntu or ZFS RaidZ on Opensolaris. Any tips? or reccomendations ? best regards TEB

    Read the article

  • How do I revert back to official Linksys firmware from dd-wrt on WRT56G2 v1?

    - by Chris Moore
    I've been having trouble with dd-wrt on my Linksys WRT56G2 v1 router and want to go back to the stock Linksys firmware for it. The router has only 2MB of flash memory, and so I'm running the 'micro' version of dd-wrt. My question is what is the best way to do that? I could use the http://router/Upgrade.asp dd-wrt "firmware upgrade" web interface to do it, in which case there's a dropdown menu choice for "After flashing, reset to": "don't reset" or "reset to default settings". Which should I pick? Some people say that I should use a program called tftp.exe instead. I can probably gain access to a Windows machine if this is necessary. Which of these is the way to proceed? I don't want to brick the router if at all possible! Note: I used the 'wrt54g' tag because I wasn't allowed to create a 'wrt54g2' tag due my low rep here.

    Read the article

  • Problem opening files with Gvim on Windows 7

    - by Oscar Duignan
    Just installed gvim on windows 7 for the first time, and I'm having a problem opening some files. When I open files vim seems to flash up a cmd window for a few second before closing it (too quickly to make out the contents,) and I end up with a C:/Program folder, and a /Files/vim/vimfiles/doc/ in the directory of the file I just opened. I can see it's trying to access C:/Program Files/vim/vimfiles/doc, which is where vim is installed, however it's choking on the space, and I'm not familiar enough with gvim to work out why. Any and all ideas are greatly appreciated.

    Read the article

  • How to scale rotated objects properly in Actionscript 3?

    - by Tom
    This is unfortunately a quite complex issue to explain, so please don't get discouraged by the wall of text - it's there for a reason. ;) I'm working on a transformation manager for flash, written with Actionscript 3. Users can place objects on the screen, for example a rectangle. This rectangle can then be selected and transformed: move, scale or rotate. Because flash by default rotates around the top left point of the object, and I want it to rotate around the center, I created a wrapper setup for each display object (eg. a rectangle). This is how the wrappers are setup: //the position wrapper makes sure that we do get the top left position when we access x and y var positionWrapper:Sprite = new Sprite(); positionWrapper.x = renderObject.x; positionWrapper.y = renderObject.y; //set the render objects location to center at the rotation wrappers top left renderObject.x = 0 - renderObject.width / 2; renderObject.y = 0 - renderObject.height / 2; //now create a rotation wrapper, at the center of the display object var rotationWrapper:Sprite = new Sprite(); rotationWrapper.x = renderObject.width / 2; rotationWrapper.y = renderObject.height / 2; //put the rotation wrapper inside the position wrapper and the render object inside the rotation wrapper positionWrapper.addChild(rotationWrapper); rotationWrapper.addChild(renderObject); Now, the x and y of the object can be accessed and set directly: mainWrapper.x or mainWrapper.y. The rotation can be set and accessed from the child of this main wrapper: mainWrapper.getChildAt(0).rotation. Finally, the width and height of the display object can be retreived and set by getting the child of the rotation wrapper and accessing the display object directly. An example on how I access them: //get wrappers and render object var positionWrapper:Sprite = currentSelection["render"]; var rotationWrapper:Sprite = positionWrapper.getChildAt(0) as Sprite; var renderObject:DisplayObject = rotationWrapper.getChildAt(0); This works perfectly for all initial transformations: moving, scaling and rotating. However, the problem arises when you first rotate an object (eg. 45 degrees) and then scale it. The scaled object is getting out of shape and doesn't scale as it should. This for example happens when you scale to the left. Scaling left is basically adding n width to the object and then reduce the x coord of the position wrapper by n too: renderObject.width -= diffX; positionWrapper.x += diffX; This works when the object is not rotated. However, when it is, the position wrapper won't be rotated as it is a parent of the rotation wrapper. This will make the position wrapper move left horizontally while the width of the object is increased diagonally. I hope this makes any sense, if not, please tell me and I'll try to elaborate more. Now, to the question: should I use a different kind of setup, system or structure? Should I maybe use matrixes, if so, how would you keep a static width/height after rotation? Or how do I fix my current wrapper system for scaling after rotation? Any help is appreciated.

    Read the article

  • 2.5" SSD in a 3.5" desktop drive bay normal?

    - by Cory Petosky
    I'm a little out of touch with modern desktop builds, but I recently built a new machine anyway. I want to pick up a SSD for my I/O intensive apps (EverQuest 2 and Flash CS4 mostly), but I'm having trouble finding any in the 3.5" form factor. Is this expected, or do I fail at product search? And, if it is expected, do 2.5" SSDs come with an adapter to fit them in my desktop machine, or will I need to purchase one separately? And, finally, if I do need to purchase an adapter, are they pretty standard or are some better than others. General advice is most welcomed, though specific product recommendations in addition would be helpful!

    Read the article

  • MS-DOS 7.1, Active-Boot

    - by user3005255
    I created a MS-DOS 7.1 (Win 98) active-boot USB-flash stick and it functions properly. Nevertheless I still have some unsolved issues: I want to change my keyboard-layout to german but I don´t know where to start since I only have the "basic-DOS" with IO.sys, MSDOS.sys + command.com. I already created Autoexec.bat + config.sys but don´t know which files I need and which I have to change in order to get a german keyboard. Also I can´t really shutdown my DOS properly, what is the right way to do it in MS-DOS 7.1? Thanks very much in advance for your help!

    Read the article

  • ARM Debian (squeeze) USB driver with mismatch 3.3.3 kernel but /lib/modules/2.6.36

    - by frank
    Hei guys, my sheevaplug embedded server works fine, but when I wanted to use USB, the device gets not attached to /dev/tty/USB0 lsusb shows correctly: Bus 001 Device 002: ID 067b:2303 Prolific Technology, Inc. PL2303 Serial Port an modprobe usbserial raises: FATAL: Could not load /lib/modules/3.3.3/modules.dep: No such file or directory in the /lib/modules/ Folder there is instead a 2.6.36-Folder uname -r gives 3.3.3 How can I overcome this mismatch? Can I create a symlink? I can't flash this embedded device since it is deployed somewhere, only ssh? Please advise!

    Read the article

  • How do I recover lost/inacessible data from my storage device?

    - by TomWij
    What steps can I take to try to recover lost or inaccessible data from any storage device? Answers: This applies to any main storage devices; eg. internal/external hard drive, USB stick, Flash memory. The most important thing is to STOP using it, any type of I/O can ruin your chances of a recovery. Click here in case you suspect corruption or bad sectors. Click here in case you suspect mechanical issues.

    Read the article

  • Why does a Windows 7 installation grow so seriously and how to shring it?

    - by Ivan
    I store all my data and the most of applications (those legally available in "portable" versions) on drive D: and only use drive C: for the Windows system and some heavily integrated applications like MS Office, Visual Studio, Adobe Reader, Flash Player etc. When I was using Windows XP, 50 GiB drive C: was more than enough. Now, as I've mitigated to Windows 7, it hardly is. Yesterday as I've checked, 7 GiBs were free on drive C:. Then I've installed fresh Windows updates (which were just some tens of MiBs to download) and checked again: now there are only 2 GiBs free. Where have 5 GiBs gone? PS: Don't be surprised my system installation takes actually that much: I've got Visual Studio and SQL Server with complete offline documentation library, but that doesn't explain where does free space disappear on simple Windows updates. PPS: I use an augmented CCleaner version to clean my PC every day, so there are for sure no temporary internet files of recycle bin trash files taking the place.

    Read the article

  • Old laptop turns off due to overheating

    - by Jake Thomas
    I have an old Laptop that powers off when the processor's temperature exceeds 84degs Celsius. The more annoying part is flash causes this the most of the times. If I watch a web feed for more than 15-20mins, it results into hard shutdown of the machine. I have an idea of a could-be solution to this problem, I want a program that would decrease the processor's clock speed to about 1.2GHz or whatever, leading it a lower temperature. Is there a program out there that does this? P.S. Someone please edit this and add the relevant tags, as I'm new and i have no idea of what tags to choose from.

    Read the article

  • Stress test a server for simultaneous connection

    - by weston smith
    I am trying to figure out a practical way to stress test a server for 300 to 600 simultaneous connections. Any advice? Thank you everyone for the help. To be more specific (sorry I wasn't before) this is a Flash Media Server on AWS that will be streaming live video. I've been having problems with the video freezing/buffering for everyone and I need to verify if its on the user end, upload end, or server end. I mainly need help with stress testing the server with 300-600 multiple request before going live.

    Read the article

  • Alternatives to the ClickToPlugin Safari extension for Chrome users

    - by Stewart Adam
    I have been using Safari with ClickToPlugin and was wondering if there was anything similar for Chrome. I am looking for both the click-through to plugin functionality as well as the HTML5 video replacements. I've done some looking around the Chrome extensions page and found some specific extensions to help with forcing the HTML5 on YouTube or to block Flash but none seem offer the generic functionality (click-through works for any given plugin) and flexibility that ClickToPlugin does (ClickToPlugin has HTML5 video replacements for a plethora of websites). I am looking to mimic the aforementioned features in Chrome, but they don't necessarily have to be provided by one single extension.

    Read the article

< Previous Page | 202 203 204 205 206 207 208 209 210 211 212 213  | Next Page >