Search Results

Search found 14780 results on 592 pages for 'low level'.

Page 206/592 | < Previous Page | 202 203 204 205 206 207 208 209 210 211 212 213  | Next Page >

  • Turn off backlight without X server commands

    - by Vi
    Fn + F6 - backlight turns off immediately, image stays (visible if shine something at the display) xset dpms force {off,suspend,standby} - backlight turns off slowly, image cleared. How to programmatically just turn off backlight on Acer Extensa 5220 laptop in Linux? It should work fast and should not touch image (unlike xset method). Ideally if I could rapidly switching backlight off and on emulate lower_than_minimum brightness level (ideally - to be hardly visible (but visible) at night).

    Read the article

  • Slow disk transfer rate

    - by Nooklez
    I have problem with slow disk transfer rate. It's static files server for our website. I was making backup of data and noticed that tar is very slow. So I did hdparm -t and... hdparm -t /dev/sda3 /dev/sda3: Timing buffered disk reads: 6 MB in 4.70 seconds = 1.28 MB/sec It's low traffic hour now on our site, so huge I/O traffic is not a reason (iotop show less than 1 MB/s). It's RAID10 setup (2x2 SATA drives). Unit UnitType Status %RCmpl %V/I/M Stripe Size(GB) Cache AVrfy ------------------------------------------------------------------------------ u0 RAID-10 OK - - 64K 1396.96 W ON VPort Status Unit Size Type Phy Encl-Slot Model ------------------------------------------------------------------------------ p0 OK u0 698.63 GB SATA 0 - WDC WD7500AADS-00M2 p1 OK u0 698.63 GB SATA 1 - WDC WD7500AADS-00M2 p2 OK u0 698.63 GB SATA 2 - WDC WD7500AADS-00M2 p3 OK u0 698.63 GB SATA 3 - WDC WD7500AADS-00M2 We have recently changed almost all components of server (excluding 3ware controller + disks). And I think problems started since then. Can it be configuration problem or hardware? EDIT: I found something like that in dmesg [166843.625843] irq 16: nobody cared (try booting with the "irqpoll" option) [166843.625846] Pid: 0, comm: swapper Not tainted 3.1.5-gentoo #3 [166843.625847] Call Trace: [166843.625848] <IRQ> [<ffffffff810859d5>] __report_bad_irq+0x35/0xc1 [166843.625856] [<ffffffff81085cec>] note_interrupt+0x165/0x1e1 [166843.625859] [<ffffffff8108445f>] handle_irq_event_percpu+0x16f/0x187 [166843.625861] [<ffffffff810844a9>] handle_irq_event+0x32/0x51 [166843.625863] [<ffffffff8108640b>] handle_fasteoi_irq+0x75/0x99 [166843.625866] [<ffffffff810039d7>] handle_irq+0x83/0x8b [166843.625868] [<ffffffff810036ad>] do_IRQ+0x48/0xa0 [166843.625871] [<ffffffff8155082b>] common_interrupt+0x6b/0x6b [166843.625872] <EOI> [<ffffffff812981e8>] ? acpi_safe_halt+0x22/0x35 [166843.625877] [<ffffffff812981e2>] ? acpi_safe_halt+0x1c/0x35 [166843.625879] [<ffffffff81298216>] acpi_idle_do_entry+0x1b/0x2b [166843.625881] [<ffffffff81298276>] acpi_idle_enter_c1+0x50/0x99 [166843.625884] [<ffffffff813b792a>] cpuidle_idle_call+0xed/0x171 [166843.625886] [<ffffffff81001257>] cpu_idle+0x55/0x81 [166843.625888] [<ffffffff81532a69>] rest_init+0x6d/0x6f [166843.625891] [<ffffffff81aa1aca>] start_kernel+0x329/0x334 [166843.625893] [<ffffffff81aa12a6>] x86_64_start_reservations+0xb6/0xba [166843.625894] [<ffffffff81aa139c>] x86_64_start_kernel+0xf2/0xf9 [166843.625896] handlers: [166843.625898] [<ffffffff812dc8de>] twl_interrupt [166843.625900] Disabling IRQ #16 It's related to problem? EDIT #2: Based on feedback in comments, here is more informations. cat /proc/interrupts 16: 390813 0 0 0 IO-APIC-fasteoi 3w-sas Controller model: [ 1.095350] 3ware Storage Controller device driver for Linux v1.26.02.003. [ 1.095467] 3ware 9000 Storage Controller device driver for Linux v2.26.02.014. [ 1.095641] LSI 3ware SAS/SATA-RAID Controller device driver for Linux v3.26.02.000. [ 1.095787] 3w-sas 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.095881] 3w-sas 0000:01:00.0: setting latency timer to 64 [ 1.910801] 3w-sas: scsi0: Found an LSI 3ware 9750-4i Controller at 0xfe560000, IRQ: 16. [ 2.216537] 3w-sas: scsi0: Firmware FH9X 5.08.00.008, BIOS BE9X 5.07.00.011, Phys: 8. [ 2.216836] scsi 0:0:0:0: Direct-Access LSI 9750-4i DISK 5.08 PQ: 0 ANSI: 5 And motherboard: description: Motherboard product: P8H67-M vendor: ASUSTeK Computer INC.

    Read the article

  • Optionally open folder in new window in vista using keyboard key

    - by lagerdalek
    In XP, to ensure a folder opened in a new window, I held down CTRL when I opened (by mouse or keyboard) the folder. This action is so ingrained to me, I pretty much don't even realise I'm doing it at a conscious level. Unfortunately, this action apparently hasn't made it to Vista. Is there a new way to do this, or am I just missing something obvious?

    Read the article

  • Semi-Hybrid Triple Channel DDR3

    - by Avihu Turzion
    I have 3 x Corsair 2GB DDR3 1600MHz, and I want to expand it with 3 more DIMMs. Obviously to keep my triple-channel, I'd be best to buy an identical 3 DIMMs kit as I have now, because triple-channel doesn't work with not-identical memory DIMMs, but to what level of difference? Can I have identical spec DIMMs (Corsair DDR3 1600MHz) but just 4GB beside my 2GB ones, and the triple-channel will still be active?

    Read the article

  • HP UX can not boot from Ignite Tape

    - by Spirit
    We have hp rp2470 server running hp-ux 11.00, with LVM mirroring. As for redundancy we have second rp2470 same hw (same two processors, same ram, same two hdd’s, same number of lan cards). I want to clone first one to the second. For that purpose I am making ignite tape with the following command: make_tape_recovery -x inc_entire=vg00 Ignite tape finishes without problems. When I boot second server from this ignate tape, server is starting to boot, and ignite restore finishes without any errors, only few notes, which are normal. However vmunix is not booting and when restore finishes, it boot to ISL prompt. From this I cannot boot /stand/vmunix. I tried to run recovery shell but no success. When recovery shell ask to do frecover to restore critical files, then I receive error: frecover(5405): unable to open /dev/rmt/0m At first I thought that the problem might be in the difference of the firmware version of the servers: fw version of production server is: Firmware Version 43.50 and fw version of backup server is: Firmware Version 42.19 So i did a fw upgrade of my backup server so that both servers are v43.50, and tried a recovery but again cant boot the system. Next I did another archive tape with -I (Interactive) flag: make_tape_recovery -I -x inc_entire=vg00 and tried recovery with it, again no good. I cannot find any error or warnings on ignite log, and I cannot boot hpux. I am only on ISL prompt. This is what i've noticed on the gsp logs: ************* SYSTEM ALERT ************** SYSTEM NAME: mcnfwim1 DATE: 07/27/2003 TIME: 10:18:49 ALERT LEVEL: 6 = Boot possible, pending failure - action required REASON FOR ALERT SOURCE: 8 = I/O SOURCE DETAIL: 6 = disk SOURCE ID: 0 PROBLEM DETAIL: 0 = no problem detail LEDs: RUN ATTENTION FAULT REMOTE POWER FLASH OFF ON ON ON LED State: Boot Failed. Running non-OS code. Check Chassis and Console Logs for error messages. 0x00000060860010B0 00000000 00000000 - type 0 = Data Field Unused 0x58000860860010B0 00006706 1B0A1231 - type 11 = Timestamp 07/27/2003 10:18:49 And another gsp log: Log Entry # 3 : SYSTEM NAME: mcnfwim1 DATE: 07/27/2003 TIME: 10:12:20 ALERT LEVEL: 6 = Boot possible, pending failure - action required SOURCE: 8 = I/O SOURCE DETAIL: 6 = disk SOURCE ID: 0 PROBLEM DETAIL: 0 = no problem detail CALLER ACTIVITY: 1 = test STATUS: 0 CALLER SUBACTIVITY: 0B = implementation dependent REPORTING ENTITY TYPE: 0 = system firmware REPORTING ENTITY ID: 00 0x00000060860010B0 00000000 00000000 type 0 = Data Field Unused 0x58000860860010B0 00006706 1B0A0C14 type 11 = Timestamp 07/27/2003 10:12:20 Type CR for next entry, - CR for previous entry, Q CR to quit. Please note that I can not change anything on the production server. I can only make changes to the backup server. Any help is appreciated.

    Read the article

  • Exchange 2003 default permissions for ANONYMOUS LOGON and Everyone

    - by Make it useful Keep it simple
    ANONYMOUS LOGON and Everyone have the following top level permissions in our Exchange 2003 Server: Read Execute Read permissions List contents Read properties List objects Create public folder Create named properties in the information store Are these the "default" settings? In particular, are the "Read" and "Execute" permissions a problem? We have a simple small business setup, Outlook clients connect to the server on the local network, OWA is used from outside the network for browser and smartphone access. Thanks

    Read the article

  • Secure data hosting...

    - by kylex
    I've looked online and can't seem to find a proper answer. We have a client that requires very sensitive data be stored in a database. Is there a hosting company that provides high-level database security (this is for a bank).

    Read the article

  • Xeon X3220 Dual-Core 2.4 GHz - which march setting for gcc?

    - by hurikhan77
    Should I use -march=nocona or -march=core2 when compiling binaries for this processor with gcc 4.3? vendor_id : GenuineIntel cpu family : 6 model : 15 model name : Intel(R) Xeon(R) CPU X3220 @ 2.40GHz stepping : 8 cpuid level : 10 flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss syscall nx lm constant_tsc arch_perfmon pebs bts rep_good pni ssse3 cx16 lahf_lm I cannot really find if this CPU is already core2 architecture... Only find information about the quad core variants, but this CPU is only dual core.

    Read the article

  • iptables & allowed port refusing connection

    - by marfarma
    Can you see what I'm doing wrong? On Ubuntu Server 9.1, I'm attempting to allow traffic on port 1143 for a non-privileged IMAP host. Connection is refused when testing with telnet example.com 1143 but connection is allowed testing with telnet example.com 80 from my pc to remote internet hosted server. Both rules appear identical and are located near each other with no rules rejecting connections intervening in the rules file. I can't figure it out. iptables -L returns this: Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere REJECT all -- anywhere 127.0.0.0/8 reject-with icmp-port-unreachable ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT tcp -- anywhere anywhere tcp dpt:www ACCEPT tcp -- anywhere anywhere tcp dpt:https ACCEPT tcp -- anywhere anywhere tcp dpt:http-alt ACCEPT tcp -- anywhere anywhere tcp dpt:7070 ACCEPT tcp -- anywhere anywhere tcp dpt:1143 ACCEPT tcp -- anywhere anywhere state NEW tcp dpt:ssh ACCEPT icmp -- anywhere anywhere icmp echo-request LOG all -- anywhere anywhere limit: avg 5/min burst 5 LOG level debug prefix `iptables denied: ' REJECT all -- anywhere anywhere reject-with icmp-port-unreachable Chain FORWARD (policy ACCEPT) target prot opt source destination REJECT all -- anywhere anywhere reject-with icmp-port-unreachable Chain OUTPUT (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere and my rules file contains this: # Generated by iptables-save v1.4.4 on Wed May 26 19:08:34 2010 *nat :PREROUTING ACCEPT [3556:217296] :POSTROUTING ACCEPT [6909:414847] :OUTPUT ACCEPT [6909:414847] -A PREROUTING -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 8080 -A PREROUTING -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 8080 COMMIT # Completed on Wed May 26 19:08:34 2010 # Generated by iptables-save v1.4.4 on Wed May 26 19:08:34 2010 *filter :INPUT ACCEPT [1:52] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [1:212] -A INPUT -i lo -j ACCEPT -A INPUT -d 127.0.0.0/8 ! -i lo -j REJECT --reject-with icmp-port-unreachable -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT -p tcp -m tcp --dport 80 -j ACCEPT -A INPUT -p tcp -m tcp --dport 443 -j ACCEPT -A INPUT -p tcp -m tcp --dport 8080 -j ACCEPT -A INPUT -p tcp -m tcp --dport 7070 -j ACCEPT -A INPUT -p tcp -m tcp --dport 1143 -j ACCEPT -A INPUT -p tcp -m state --state NEW -m tcp --dport 22 -j ACCEPT -A INPUT -p icmp -m icmp --icmp-type 8 -j ACCEPT -A INPUT -m limit --limit 5/min -j LOG --log-prefix "iptables denied: " --log-level 7 -A INPUT -j REJECT --reject-with icmp-port-unreachable -A FORWARD -j REJECT --reject-with icmp-port-unreachable -A OUTPUT -j ACCEPT COMMIT # Completed on Wed May 26 19:08:34 2010

    Read the article

  • Is the /etc/inittab file read top down?

    - by PeanutsMonkey
    When the init process is executed when the kernel has loaded, does it read the /etc/inittab file in a top down approach i.e. it executes each line as it appears in the file. If so and based on my reading and understanding, does this mean that it enters the documented run level and then launch sysinit process or vice versa? For example the common examples I have seen are id:3:initdefault: # System initialization. si::sysinit:/etc/rc.d/rc.sysinit

    Read the article

  • Can ZenOSS integrate Ganglia smoothly?

    - by chen
    I like Ganglia for its Gmetric function, and I like its multi-layer capability. But Ganglia does not have healthiness check, alerting and etc. for the server monitor functionality. So it would be great to bring this two species together. Sure, we can install Ganglia, and then install ZenOSS. But is there a plugin or something that can smoothly integrate them together? At least integration at the presentation level. Thanks

    Read the article

  • Can anyone recommend a decent tool for optimizing images other than Photoshop

    - by toomanyairmiles
    Can anyone recommend a decent tool for optimising images other than adobe photoshop, the gimp etc? I'm looking to optimise images for the web preferably online and free. Basically I have a client who can't install additional software on their work PC but needs to optimise photographs and other images for their website and is presently uploading 1 or 2 Mb files. On a personal level I'm interested to see what other people are using...

    Read the article

  • Using IIS7 why are my PNGs being cached by the browser, but my JS and CSS files not?

    - by Craig Shearer
    I am trying to sort out caching in IIS for my site. Basically, I want nothing cached, except for .png, .js, and .css files. At my site level, I opened the HTTP Reponse Headers and used the "Set Common Hedaers..." to set content to expire immediately. I have no Output Caching profiles set at any level in IIS. I clear my browser cache then try accessing my site. When my site requests a PNG file, I see responses like: Accept-Ranges bytes Age 0 Connection Keep-Alive Content-Type image/png Date Thu, 12 Apr 2012 21:55:15 GMT Etag "83b7322de318cd1:0" Last-Modified Thu, 12 Apr 2012 19:33:45 GMT Server Microsoft-IIS/7.5 X-Powered-By ASP.NET For JS and CSS files, I see responses like: Accept-Ranges bytes Cache-Control no-cache Connection Keep-Alive Content-Encoding gzip Content-Length 597 Content-Type text/css Date Thu, 12 Apr 2012 21:55:15 GMT Etag "06e45ede15bca1:0" Last-Modified Mon, 02 Nov 2009 17:28:44 GMT Server Microsoft-IIS/7.5 Vary Accept-Encoding X-Powered-By ASP.NET Accept-Ranges bytes Cache-Control no-cache Connection Keep-Alive Content-Encoding gzip Content-Length 42060 Content-Type application/x-javascript Date Thu, 12 Apr 2012 21:55:14 GMT Etag "2356302de318cd1:0" Last-Modified Thu, 12 Apr 2012 19:33:45 GMT Server Microsoft-IIS/7.5 Vary Accept-Encoding X-Powered-By ASP.NET So, why are my PNGs able to be cached, but JS and CSS files not? Then, I go into the Output Caching feature in IIS and set up profiles for .png, .css, and .js files. This updates the web.config file as follows: <caching> <profiles> <add extension=".png" policy="CacheUntilChange" kernelCachePolicy="DontCache" /> <add extension=".css" policy="CacheUntilChange" kernelCachePolicy="DontCache" /> <add extension=".js" policy="CacheUntilChange" kernelCachePolicy="DontCache" /> </profiles> </caching> I do a "precautionary" IISReset then try accessing my site again. For PNG files, I see the following response: Accept-Ranges bytes Age 0 Connection Keep-Alive Content-Length 3833 Content-Type image/png Date Thu, 12 Apr 2012 22:02:30 GMT Etag "0548c9e2c5dc81:0" Last-Modified Tue, 22 Jan 2008 19:26:00 GMT Server Microsoft-IIS/7.5 X-Powered-By ASP.NET For CSS and JS files, I see the following responses: Accept-Ranges bytes Cache-Control no-cache,no-cache Connection Keep-Alive Content-Encoding gzip Content-Length 2680 Content-Type application/x-javascript Date Thu, 12 Apr 2012 22:02:29 GMT Etag "0f743af9015c81:0" Last-Modified Tue, 23 Oct 2007 16:20:54 GMT Server Microsoft-IIS/7.5 Vary Accept-Encoding X-Powered-By ASP.NET Accept-Ranges bytes Cache-Control no-cache,no-cache Connection Keep-Alive Content-Encoding gzip Content-Length 3831 Content-Type text/css Date Thu, 12 Apr 2012 22:02:29 GMT Etag "c3f42d2de318cd1:0" Last-Modified Thu, 12 Apr 2012 19:33:45 GMT Server Microsoft-IIS/7.5 Vary Accept-Encoding X-Powered-By ASP.NET What am I doing wrong? Have I completely misunderstood the features of IIS, or is there a bug. Most importantly, how do I achieve what I want - that is get the browser to cache only PNG, JS and CSS files?

    Read the article

  • Thoughts on home NAS server

    - by user826955
    I currently have a NAS with a 2x2TB HDD 1x16GB SSD layout on a mini-itx atom board. The NAS is in a Lian Li PC-Q07 case. On this system I was running freebsd 8 with a gmirror raid 1 setup, which was enough for my needs. So far I was using the NAS for: Fileserver with AFP protocol (only mac clients used) SVN server hosting all my source trees of my projects JIRA (performance was okay-ish) Timemachine backup for the macs The power consumption was about 38W, although I did not put HDDs asleep when unused (I think this is not possible in a raid setup). I liked the NAS because: the performance was good through gigabit LAN (enough for my needs) power consumption was good its a pretty small case and fits in one of my cupboards I disliked the NAS a bit because: it was a bit noisy, the Q07 case vibrated a good amount because of the HDDs. I switched the NAS off every evening I do not have a real backup of the data on the NAS, only the internal raid 1 as safety. I really dont want to loose my source trees under no circumstances, so I would really be sleeping better if I knew I had regular backups somewhere. Recently, the board seemed to have died, I can't boot anymore. Thus, I was thinking about a redesign of my NAS (I still have to find out what parts are broken, I probably need to replace the mainboard and SSD. HDDs seem to be okay). First of all, I was wondering what other users have as backup for their NAS? Are you actually using a second NAS, and regularly copying over the data to have it safe? Or is there any better solution to this? I was thinking about getting a cheap NAS like the synology DS112j with only one disk, and use rsync or something similar to regularly copy data over to the second NAS (wake the second NAS upon start, shut it down after copy). Although this approach seems somewhat weird, It would have the benefit (?) that I could use a single disk instead of raid in the main NAS, and put the disk asleep when idle, and have the NAS running 24/7 with low energy consumption (I found no way to do this with a gmirror setup). Is there any recommended backup solution for a small NAS? Then I was thinking about a different raid setup. Since I have to buy a new mainboard as well as SSD, I might as well switch over to a i3 board with more ram, and also switch to ZFS. I am not familar with ZFS, I've never used it, but I read and hear much about it. Would it be viable to set up a ZFS storage with only 2 disks? Can I easily extend this storage with more disks, once I choose to add some? I could maybe get a new case like the Fractal Design Array R2 which has more 3,5" slots. I could as well get another 2 disks, but I would prefer sticking with the existing 2 for enegery/heat/noise reasons. Should I go for a ZFS storage or stick to my gmirror setup? I would also like to keep freebsd as operating system, and also I dont need any web gui or something (that is, I dont need/want to use FreeNAS or Openfiler etc). Does anyone maybe have a sample setup in use so I can compare energy consumption/noise/software setup? Any guidance towards the NAS of my dreams (silent, low energy, safe w/ backups) much appreciated.

    Read the article

  • HP DL380 using HP NC522SFP NIC shows supported link modes: not reported

    - by MikeS
    When using ethtool on this NIC, the supported link modes show "not reported". Any idea why this is the case? Settings for eth0: Supported ports: [ FIBRE ] Supported link modes: Not reported Supported pause frame use: Symmetric Supports auto-negotiation: No Advertised link modes: Not reported Advertised pause frame use: No Advertised auto-negotiation: No Speed: 10000Mb/s Duplex: Full Port: FIBRE PHYAD: 1 Transceiver: external Auto-negotiation: off Supports Wake-on: g Wake-on: g Current message level: 0x00002000 (8192) hw Link detected: yes

    Read the article

  • Limit user profile on specific OU using Group Policy

    - by Sergei
    We have a host that will be used for creating VM clones from time to time for testing purposes.It is used actively for testing and users tend to keep a lot of files in their profiles.We would like to limit users profile size to avoid cloning unnecessary files to new VMs. Is there way to impose limit on user profile on OU level without introducing roaming profiles?

    Read the article

  • Preserve indention converting RTF to TXT on OS X

    - by Dan
    I made a multi-level bulleted list in TextEdit that looks something like: foo bar stuff things However, when I try to convert it to text (via cmd-shift-T, copy and paste, or textutil), the result looks more like: foo bar stuff things How can I convert to text but preserve the indention?

    Read the article

  • /etc/init.d/libvirtd start fails but service libvirtd start works. Why?

    - by Gregg
    CentOS 6.3, running as root (Shush). Can you please tell me why I would get initialisation failures from the init scripts but the service command works a treat? There was nothing in /var/log/messages or /var/log/libvirt/* all I have it the Terminal output: /etc/init.d/libvirtd start Starting libvirtd daemon: libvirtd: initialization failed [FAILED] I changed the libvirtd logging level to 1, the highest, but saw nothing in messages after another failure.

    Read the article

  • Generate a limited amount of random network traffic between 2 hosts

    - by Andrew S
    I'm trying to find a utility that will allow me to generate a constant flow of random network traffic at a specified rate between 2 hosts. The utility needs to run on Windows and OSX. I've tried iperf but it seems to be more oriented toward short-term testing/statistics and it really taxes the CPU even at slower rates. I want something that will generate traffic for a few weeks at say 10Mbps while I use other tools to monitor the impact of that level of traffic on the network.

    Read the article

< Previous Page | 202 203 204 205 206 207 208 209 210 211 212 213  | Next Page >