Search Results

Search found 6942 results on 278 pages for 'enabled'.

Page 207/278 | < Previous Page | 203 204 205 206 207 208 209 210 211 212 213 214  | Next Page >

• Linux: 3 Monitor PCI-e Graphics card (without tremendous pain)?

  - by N Rahl

  As we are all painfully aware, the only way to get multiple monitors AND compositing (Compiz) on Linux is to use a single graphics card that can drive both (or in my case all three) screens. I bought a Radeon 5750 specifically because it claims to able to drive 3 monitors. I can plug in 3 monitors (2 DVI, 1 HDMI) and the Catalyst Control Center shows all 3, but only 2 can be enabled at a time. I'll post the exact error message here soon, but it's very useless. So I'm going to assume that either the 5750 doesn't support 3 monitors, OR, more likely, ATI couldn't be bothered to add that support to their Linux drivers. So this is a multipart question: First, can anyone suggest a PCI Express Graphics card that can run 3 screens on linux without tremendous pain? I'm looking for something where you install the driver and all three screens "just work". Does such a card exist? Second, if you have a 5750, have you been able to get it to do 3 monitors? I'm running Ubuntu 10.04 at the moment. Thanks, Nick

  Read the article

• Linux: Encryption of a physical LVM volume doesn't imply encryption of its logical subvolumes?

  - by java.is.for.desktop

  Hello, everyone! I installed OpenSuse one year ago on my notebook. I created all partitions except /boot inside an LVM partition. I enabled encryption for it during setup. The system asked me a password on each boot later. Everything seemed fine... But one day I wanted to cancel the boot process and did it with SysRq REISUB. During entering this combination, the system suddenly continued to boot without any password being entered. I had no /home and no swap, but / was mounted! I checked multiple times, it was inside an "encrypted" physical LVM volume. Later I found out that OpenSuse can't encrypt / at all. There is an option to enable encryption for each logical volume, and indeed it fails for /. Later I tried Fedora. The options during partitioning were misleading by same means. I could enable "encryption" of a physical volume and each logical subvolume. With the exception that Fedora actually allowed to encrypt /. Question: What's the point of setting up "encryption" for a physical LVM volume, when it doesn't imply (real) encryption of its logical subvolumes? Did I get something wrong in this whole concept?

  Read the article

• apache segmentation error

  - by lush

  I can't start Apache with the following errors: [root@web]# /etc/init.d/httpd start Starting httpd: /bin/bash: line 1: 19232 Segmentation fault /usr/sbin/httpd [root@web]# /usr/sbin/apachectl -k start /usr/sbin/apachectl: line 102: 19919 Segmentation fault $HTTPD $OPTIONS $ARGV I use webmin control panel and I've already tried re-installing Apache from scratch. Can someone advise what else I should try to do? Many thanks. UPDATE: The only line is always written in the error logs which seems not to be very important: [Mon Nov 14 19:00:09 2011] [notice] suEXEC mechanism enabled (wrapper: /usr/sbin/suexec) UPDATE 2: I've recently had the error below in the logs. Looks like some modules are incompatible, so I've just disabled these extensions: fileinfo and mcrypt in my php.ini. I should be able to start the web server without them. PHP Warning: PHP Startup: fileinfo: Unable to initialize module\nModule compiled with module API=20050922, debug=0, thread-safety=0\nPHP compiled with module API=20060613, debug=0, thread-safety=0\nThese options need to match\n in Unknown on line 0 PHP Warning: Module 'mcrypt' already loaded in Unknown on line 0 UPDATE 3: [root@web]# file /usr/sbin/httpd /usr/sbin/httpd: ELF 64-bit LSB shared object, AMD x86-64, version 1 (SYSV), for GNU/Linux 2.6.9, stripped [root@web]# uname -m x86_64

  Read the article

• Scripted redirection for Outlook 2003

  - by John Gardeniers

  We have a staff member in sales who has gone onto a 4 day week (getting ready for retirement), so each Thursday afternoon her email needs to be forwarded to another user and each Friday afternoon it needs to be set back. I'm using the VBS script below to do this, run via the Task Scheduler. Although the script appears to do it's job, based on what I see when I view the user's Exchange settings, Exchange doesn't always recognise that the setting has changed. e.g. Last Thursday the forwarding was a enabled and worked correctly. On Friday the script did it's thing to clear the forwarding but Exchange continued to forward messages all weekend. I found that I can force Exchange to honour the changed setting be merely opening and closing the user's properties in ADUC. Of course I don't want to have to do that. Is there a non-manual way I can have Exchange read and honour the setting? The script (VBS): ' Call this script with the following parameters: ' ' SrcUser - The logon ID of the suer who's account is to be modified ' DstUser - The logon account of the person to who mail is to be forwarded ' Use "reset" to clear the email forwarding SrcUser = WScript.Arguments.Item(0) DstUser = WScript.Arguments.Item(1) SourceUser = SearchDistinguishedName(SrcUser) 'The user login name Set objUser = GetObject("LDAP://" & SourceUser) If DstUser = "reset" then objUser.PutEx 1, "altRecipient", "" Else ForwardTo = SearchDistinguishedName(DstUser)' The contact common name objUser.Put "AltRecipient", ForwardTo End If objUser.SetInfo Public Function SearchDistinguishedName(ByVal vSAN) Dim oRootDSE, oConnection, oCommand, oRecordSet Set oRootDSE = GetObject("LDAP://rootDSE") Set oConnection = CreateObject("ADODB.Connection") oConnection.Open "Provider=ADsDSOObject;" Set oCommand = CreateObject("ADODB.Command") oCommand.ActiveConnection = oConnection oCommand.CommandText = "<LDAP://" & oRootDSE.get("defaultNamingContext") & ">;(&(objectCategory=User)(samAccountName=" & vSAN & "));distinguishedName;subtree" Set oRecordSet = oCommand.Execute On Error Resume Next SearchDistinguishedName = oRecordSet.Fields("DistinguishedName") On Error GoTo 0 oConnection.Close Set oRecordSet = Nothing Set oCommand = Nothing Set oConnection = Nothing Set oRootDSE = Nothing End Function

  Read the article

• What's Keeping My Computer Awake?

  - by phantomdata

  First the question; How do I figure out what is preventing my Windows 7 computer from going into sleep mode? Second; some background... I've been struggling with this for a few days and am utterly perplexed. I setup sleep mode on my Windows 7 PC a few weeks ago, and all was well. The PC would sleep as expected and I was snuggly in knowing that my computer was saving power and some wear and tear on the components (we'll leave the 'is it better to sleep' debate for another thread/day, please don't start it). Well, I noticed the other night that my system stopped ever going to sleep. I set the sleep time down to 1 minute and wandered fully away from the PC (ensuring that no errant mouse or keyboard movements would occur) and the PC never went to sleep. I've also observed this over longer intervals as well, such as overnight. I have sleep mode enabled, of course "multimedia settings - When Sharing Media" is set to allow the computer to sleep. "powercfg -lastwake" show nothing of interest, since it never goes to sleep and can't wake up. "powercfg /requests" shows 3 entries - all "[DRIVER] ?". I assume that 2 of these are my mouse and keyboard - as I've recently used them to run the powercfg command. I'm at a loss for the third though. I've unhooked all USB peripherals save for my keyboard and mouse. Wake on LAN is disabled in my BIOS. I know that you can disable all apps from waking/preventing sleep - but I want the ability to remain for those apps that do legitimately need to keep the system awake. So; does anyone know of a way to figure out what the 3rd phantom "[DRIVER] ?" is in powercfg /requests?

  Read the article

• suPHP not working

  - by amarc

  OS: Ubuntu 10.04 etc/suphp/suphp.conf: [global] ;Path to logfile logfile=/var/log/suphp/suphp.log ;Loglevel loglevel=info ;User Apache is running as webserver_user=www-data ;Path all scripts have to be in docroot=/home ;Path to chroot() to before executing script ;chroot=/mychroot ; Security options allow_file_group_writeable=false allow_file_others_writeable=false allow_directory_group_writeable=false allow_directory_others_writeable=false ;Check wheter script is within DOCUMENT_ROOT check_vhost_docroot=true ;Send minor error messages to browser errors_to_browser=false ;PATH environment variable env_path=/bin:/usr/bin ;Umask to set, specify in octal notation umask=0077 ; Minimum UID min_uid=100 ; Minimum GID min_gid=100 [handlers] ;Handler for php-scripts application/x-httpd-suphp="php:/usr/bin/php-cgi" ;Handler for CGI-scripts x-suphp-cgi="execute:!self" some vhost in sites-enabled: NameVirtualHost *:8080 <VirtualHost *:8080> ServerAdmin ... ServerName ... ServerAlias ... AddType application/x-httpd-php .php AddHandler application/x-httpd-php .php suPHP_Engine on suPHP_UserGroup user user suPHP_ConfigPath "/home/user/etc" suPHP_PHPPath /usr/bin DocumentRoot /home/user/web/site.com/ ErrorLog /var/log/apache2/site.com-error_log CustomLog /var/log/apache2/site.com-access_log common <Directory /home/user/web/site.com/> Order Deny,Allow Allow from all Options +Indexes </Directory> </VirtualHost> But when I did nano /home/user/web/id.php and paste <?php system('id'); ?> in it, result I get is: uid=33(www-data) gid=33(www-data) groups=33(www-data) Have no idea what to do so I was hoping comunity could help ty.

  Read the article

• RDP suggesting a user name when connecting to a server

  - by Neolisk

  Prior to Event X, RDPing to Server 2003 always caused the user name appear blank and Login to be enabled, so you could pick to which domain you would log in. For us it's either local or our domain. Since a recent Event X a domain + user name is being suggested for every server and it's not the most recently used user name. If you remove it manually from RDP dialog, it's still being pre-populated for you, and then at the next available opportunity it returns into General/User name option of RDP dialog. So user name field comes pre-populated and you cannot change to log in locally (only if you manually erase domain specifier - everything before \) - Log in to option is disabled by default. We did not do any changes to our domain or client machines, so I am suspecting some Windows update caused it (and this being Event X). Interesting fact - it does not consistently happen on all machines, and some can login to some servers fine, while other servers keep suggesting a default user name. What could be that Event X and is there a way to fix it? EDIT: I tried this - How to clear remote desktop connections history and specifically this part of it: reg delete "HKEY_CURRENT_USER\Software\Microsoft\Terminal Server Client\UsernameHint" /f The problem still persists.

  Read the article

• Apache APC (Windows) Can I optimize these APC settings more?

  - by ar099968

  I would like to optimize APC some more but I am not sure where I could do something. First here is the stats after 1 week of running with the current configuration: General Cache Information APC Version 3.1.9 PHP Version 5.4.4 APC Host XXXXXXXXXXXXXXXXXXXXXXXXXXXXXX Server Software Apache Shared Memory 1 Segment(s) with 128.0 MBytes (IPC shared memory, Windows Slim RWLOCK (native) locking) Start Time 2014/06/08 05:00:00 Uptime 6 days, 11 hours and 55 minutes File Upload Support 1 Host Status Diagrams Memory Usage Free: 99.7 MBytes (77.9%) Used: 28.3 MBytes (22.1%) Hits & Misses Hits: 510818 (99.9%) Misses: 608 (0.1%) Detailed Memory Usage and Fragmentation Fragmentation: 0.60% (609.8 KBytes out of 99.7 MBytes in 83 fragments) File Cache Information Cached Files 693 ( 35.4 MBytes) Hits 5143359 Misses 1087 Request Rate (hits, misses) 13.24 cache requests/second Hit Rate 13.24 cache requests/second Miss Rate 0.00 cache requests/second Insert Rate 0.01 cache requests/second Cache full count 0 User Cache Information Cached Variables 0 ( 0.0 Bytes) Hits 0 Misses 0 Request Rate (hits, misses) 0.00 cache requests/second Hit Rate 0.00 cache requests/second Miss Rate 0.00 cache requests/second Insert Rate 0.00 cache requests/second Cache full count 0 Runtime Settings apc.cache_by_default 1 apc.canonicalize 1 apc.coredump_unmap 0 apc.enable_cli 0 apc.enabled 1 apc.file_md5 0 apc.file_update_protection 2 apc.filters -/apc.php$, -/apc_clean.php$, -.tpl.cache.php$, -.tpl.php$, -.string.cache.php$, -.string.php$ apc.gc_ttl 3600 apc.include_once_override 0 apc.lazy_classes 0 apc.lazy_functions 0 apc.max_file_size 2M apc.num_files_hint 7000 apc.preload_path apc.report_autofilter 0 apc.rfc1867 0 apc.rfc1867_freq 0 apc.rfc1867_name APC_UPLOAD_PROGRESS apc.rfc1867_prefix upload_ apc.rfc1867_ttl 3600 apc.serializer default apc.shm_segments 1 apc.shm_size 128M apc.shm_strings_buffer 4M apc.slam_defense 0 apc.stat 1 apc.stat_ctime 0 apc.ttl 7200 apc.use_request_time 1 apc.user_entries_hint 4096 apc.user_ttl 7200 apc.write_lock 1

  Read the article

• Powershell Get-Process cannot connect to remote computer

  - by amandion

  I've been struggling with this for a few hours and can't figure this out. I have two Windows 7 computers. One is my workstation that is using Powershell to do administrative maintenance. The other is the machine I'd like to use Powershell remoting on to execute remote Powershell cmdlets on. On both computers, I've enabled Powershell remoting and added all computers to TrustedHosts with the * value. On the remote computer, I've started the Remote registry service and ensured that the DCOM, Winmgmt and the Winrm services are running. Firewall is disabled on remote machine too. The cmdlet I try to run is: Get-Process -ComputerName $name Where $name is the name of the remote machine. I keep getting an error saying that it could not connect to the remote PC. I've also tried using the IP and I get the same error. These PCs are not in a domain. I am able to do the following successfully: Invoke-Command {get-Process} -ComputerName $name -Credential $creds Where $name is the machine name and $creds is the user name and password for the remote computer's local Admin account. This gives me the same output I would expect. While this is an acceptable workaround, I am curious, why doesn't using get-process with remoting work as it should? I've seen a few articles on the web suggesting people have had success with it on its own. Each time I am using Powershell on my workstation with elevated privileges. Any ideas?

  Read the article

• Setting up Virtual Host in Fedora Core 15 using apache

  - by Roland

  I'm trying to setup a couple of Virtual Host files on my Localhost PC running Fedora Core 15. Now I get this working, but now onloy one Virtual Host site works, and if I type in 127.0.0.1/test/testApp.php which is not related to the Virtual Host site , I get redirected to the Virtual Host site. Here's what I did. I created a new folder called virtualhosts in /etc/httpd/ where all my host files are stored in the following format site.conf In /etc/conf/httpd.conf I enabled NameVirtualHost *:80 and included the host files at the bottom of the config page like this Include virtualhosts/*.conf In /etc/hosts I added the line 127.0.0.1 website No when I run sudo httpd -t I get Syntax OK I restart apache and then the Virtualhost works, but as soon as I add other hosts and only use 127.0.0.1 as above it still links to the original host. Am I doing anything wrong here or left out something? An example of my Virtual Host file looks like this <VirtualHost *:80> ServerAdmin [email protected] DocumentRoot /var/www/html/website/ ServerName website ServerAlias website ErrorLog logs/dev-error_log CustomLog logs/dev-access_log common Alias /blog /var/www/html/blog/ <Directory /var/www/html/website/> Options FollowSymLinks Allow Override All Order allow,deny allow from all </Directory> #php_value error_reporting E_ALL & ~E_NOTICE & ~E_DEPRECATED php_flag display_errors On php_value date.timezone Europe/London </VirtualHost>

  Read the article

• HPET missing from available clocksources on CentOS

  - by squareone

  I am having trouble using HPET on my physical machine. It is not available, even though I have enabled it in my bios, forced it in grub, and triple checked my kernel to include HPET in its compilation. Motherboard: Supermicro X9DRW Processor: 2x Intel(R) Xeon(R) CPU E5-2640 SAS Controller: LSI Logic / Symbios Logic SAS2004 PCI-Express Fusion-MPT SAS-2 [Spitfire] (rev 03) Distro: CentOS 6.3 Kernel: 3.4.21-rt32 #2 SMP PREEMPT RT x86_64 GNU/Linux Grub: hpet=force clocksource=hpet .config file: CONFIG_HPET_TIMER=y CONFIG_HPET_EMULATE_RTC=y CONFIG_HPET=y dmesg | grep hpet: Command line: ro root=/dev/mapper/vg_xxxx-lv_root rd_NO_LUKS rd_LVM_LV=vg_xxxx/lv_root KEYBOARDTYPE=pc KEYTABLE=us rd_NO_MD SYSFONT=latarcyrheb-sun16 crashkernel=auto rd_LVM_LV=vg_xxxx/lv_swap rd_NO_DM LANG=en_US.UTF-8 rhgb quiet panic=5 hpet=force clocksource=hpet Kernel command line: ro root=/dev/mapper/vg_xxxx-lv_root rd_NO_LUKS rd_LVM_LV=vg_xxxx/lv_root KEYBOARDTYPE=pc KEYTABLE=us rd_NO_MD SYSFONT=latarcyrheb-sun16 crashkernel=auto rd_LVM_LV=vg_xxxx/lv_swap rd_NO_DM LANG=en_US.UTF-8 rhgb quiet panic=5 hpet=force clocksource=hpet cat /sys/devices/system/clocksource/clocksource0/current_clocksource: tsc cat /sys/devices/system/clocksource/clocksource0/available_clocksource: tsc jiffies What is even more confusing, is that I have about a dozen other machines that utilize the same kernel .config, and can use HPET fine. I fear it is a hardware issue, but would appreciate any advice or help with getting HPET available. Thanks in advance!

  Read the article

• Hyper-V VM's cannot access Host resources, and vice-versa

  - by Agent

  I have several Hyper-V vm's running on this Win2008 R2 Server box, and up until a reboot of the host server, all the VM's were able to access shared folders on the host. Now, they can't even ping the host server. From what I've seen, I need to setup an Internal only network through Virtual Network Manager in Hyper-V. I set this up, then tried to enable the Microsoft Virtual Network Switch Protocol option in this Internal Only NIC, but I get popups saying: Your current selection will also disable the following features: Microsoft virtual network switch protocol Which is absolutely stupid, considering the protocol is what I'm ticking the checkbox to Enable! As of now, on the host, I have 2 NICs: Physical - This NIC on the host machine does have the MVNS protocol enabled Virtual Network Adapter - Created through Hyper-V Virtual Network Manager as an External type of network. Trying to enable MVNS on this NIC also produces the error above. I've tried enabling Client for Microsoft Networks on the physical NIC for IPv6, but everytime I do that, all the VMs lose Internet connectivity and I cannot RDP into them. Anything else I can try?

  Read the article

• TCP/UDP hole punching from and to the same NAT network

  - by Luc

  I was wondering if tcp/udp hole punching would still work when you are in the same network (behind a NAT), and what the packet's path would be. What happens when using hole punching on the same network, is that it will send a packet out with the same destination and source address. Only the source and destination port would differ. I imagine a router with NAT loopback enabled will handle this as it should, but how about other routers? Would they drop the packet, or would a router (the first?) from the ISP bounce the packet back after which it gets handled okay? I'm wondering because I was thinking about using this technique to circumvent a block between peers in a network (like a school network where clients can only access the internet, but any contact with each other is blocked). The only other option is to use a man in the middle as proxy (tunnel?). The disadvantage of this is that you have to have a server with significantly more bandwidth than one that would only do hole punching. Also the latency would increase significantly.

  Read the article

• Apache2 403 permission denied on Ubuntu 12.04

  - by skeniver

  I have a sub-directory in my /var/www folder called prod, which is password protected. It was all working fine until I asked my server admin to help me set up allow all access to one particular file. Now the entire folder is just giving me a 403 error. This is the sites-enabled file: <VirtualHost *:80> ServerAdmin [email protected] # Server name ServerName prod.xxx.co.uk DocumentRoot /var/www/prod <Directory /var/www/prod> Options Indexes FollowSymLinks MultiViews +ExecCGI Includes AllowOverride None Order allow,deny AuthType Basic AuthName "Please log in" AuthUserFile /home/ubuntu/.htpasswd Require valid-user </Directory> <Directory /var/www/prod/xxx/cgi-bin/api.pl> Allow from All Satisfy Any </Directory> ScriptAlias /xxx/cgi-bin/ /var/www/prod/xxx/cgi-bin/ ErrorLog ${APACHE_LOG_DIR}/prod.xxx.error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog ${APACHE_LOG_DIR}/prod.xxx.access.log combined </VirtualHost> Now he's unsure why this is blocking me out completely. No permissions have been changed, but this is the /var/www/ folder: 4 drwxr-xr-x 2 root root 4096 Jan 3 21:10 images 4 drwxr-sr-x 4 root www-data 4096 Mar 31 14:47 jslib 4 drwxr-xr-x 7 root root 4096 Jun 2 13:00 prod When I try to visit http://prod.xxx.co.uk, I don't get asked for the password; I just get 403'd I hope I've given enough information... Anyone able to spot something he can't?

  Read the article

• Glassfish and SSL [closed]

  - by Richard

  I'm struggling to get SSL working on Glassfish 3.1.1. I've been following tutorials like http://javadude.wordpress.com/2010/04/06/getting-started-with-glassfish-v3-and-ssl/ and SO posts like this Issues with setting up SSL on Glassfish v3 The above links are for information only. I've summarised what I've done below. As far as I can tell I'm doing everything correctly but I'm getting this error: SSL configuration is invalid due to No available certificate or key corresponds to the SSL cipher suites which are enabled Some background of what I have done: My cert is from GoDaddy. I generated the CSR from a new keystore (keystore.jks), then imported the resulting certs back into the same keystore and set the keystore password to the same pwd as the GF master password. Then created a new SSL listener in GF and pointed it at my keystore file (which I copied into domains/domain1/config). Set the Nickname to the alias of my cert (which is something liem 'mydomain.org' i.e. the name that I get when I run keytool -list. In my ciphers section in the network listeners page, I leave the defaults in place (empty, which means all ciphers are available I think). In domain.xml I've replaced all instances of s1as to 'mydomain.org'. This is the question: What exactly is causing the error highlighted? I'm guessing it's a mismatch between my listener config and aliases in my keystore, or something similar, but I'm not really sure what. Thanks

  Read the article

• virtual host settings fail on multiple sites

  - by Ricalsin

  Wow. I'm puzzled. On my ubuntu system I've setup an apache2 server and configured three virtual hosts in the /etc/apache2/sites-available directory. a2ensite to symbolic link the sites-enabled. The first two work great; a simple url of localhost.mysitenames.com works great for the first two sites, both finding their DocumentRoot and Directory paths. The third always generates a Bad Request (Invalid Hostname) response. No server error.log as it never hits it. I've copied/pasted the working vhost files, made the minor changes to the ServerName, DocumentRoot and Directory and the same problem persists. I always "sudo /etc/init.d/apache2 restart" whenever I make a change. I've cleared the browser cache as well. No love. There's not a limit to the number of sites you can host, right? My goal was a localhost development environment with the expectation I can run any number of websites locally before pushing them to a live server. Any thoughts on how to debug this? Or, just a simple solution I am missing?

  Read the article

• MySQL Tables Missing/Corrupt After Recreation

  - by Synetech inc.

  Hi, Yesterday I dumped my MySQL databases to an SQL file and renamed the ibdata1 file. I then recreated it and imported the SQL file and moved the new ibdata1 file to my MySQL data directory, deleting the old one. I’ve done it before without issue, however this time something is not right. When I examine the (personal, not MySQL config) databases, they are all there, but they are empty… sort of. The data directory still has the .ibd files with the correct content in them and I can view the table list in the databases, but not the tables themselves. (I have file-per-table enabled, and am using InnoDB as default for everything.) For example with the urls database and its urls table, I can successfully open mysql.exe or phpMyAdmin and use urls;. I can even show tables; to see the expected table, but then when I try to describe urls; or select * from urls;, it complains that the table does not exist (even though it just listed it). (The MySQL Administrator lists the databases, but does not even list the tables, it indicates that the dbs are completely empty.) The problem now is that I have already deleted the SQL file (and cannot recover it even after scouring my hard-drive). So I am trying to figure out a way to repair these databases/tables. I can’t use the table repair function since it complains that the table does not exist, and I can’t dump them because again, it complains that the tables don’t exist. Like I’ve said, the data itself is still present in the .ibd files and the table names are present. I just need a way to get MySQL to recognize that the tables exist in the databases (I can find the column names of the tables in question in the ibdata1 file using a hex-editor). Any idea how I can repair this type of corruption? I don’t mind rolling up my sleeves, digging in, and taking a bunch of steps to fix it. Thanks a lot.

  Read the article

• How to prevent an SSD from disappearing from BIOS

  - by Midimatt

  I've only recently upgraded my old machine to a new one with a brand new 60gb SSD as my boot drive and a 1TB main drive. Paranoid about completely breaking my SSD, I read up on a lot of issues that I needed to watch out for, including making sure AHCI was turned on and trim enabled. PC has been working fine for a few weeks now, until today. My wife was watching some TV on the machine when it started to act strange and eventually blue screened. She rebooted and the boot mgr was missing. When I got home from work I checked the BIOS and the drive had disappeared. I panicked and looked up some possible fixes, and I discovered a large amount of people having problems with the drive firmware, especially on OCZ Vertex and Agility drives, and my drive is an Agility 3 drive. The problems included blue screens followed by missing drives, and a solution was to reset the CMOS and try again. This worked, and now everything seems to be working fine. My question is, is there any way to prevent this from happening? Am I missing a setting for my SSD? All of the posts I found were from early to mid-2011 nothing for the end of 2011 to 2012. So I am wondering if I've missed anything. EDIT: Checked my drives firmware and it is 2.15, which has had issues reported by users.

  Read the article

• MSMQ on Win2008 R2 won't receive messages from older clients

  - by Graffen

  I'm battling a really weird problem here. I have a Windows 2008 R2 server with Message Queueing installed. On another machine, running Windows 2003 is a service that is set up to send messages to a public queue on the 2008 server. However, messages never show up on the server. I've written a small console app that just sends a "Hello World" message to a test queue on the 2008 machine. Running this app on XP or 2003 results in absolutely nothing. However, when I try running the app on my Windows 7 machine, a message is delivered just fine. I've been through all sorts of security settings, disabled firewalls on all machines etc. The event log shows nothing of interest, and no exceptions are being thrown on the clients. Running a packet sniffer (WireShark) on the server reveals only a little. When trying to send a message from XP or 2003 I only see an ICMP error "Port Unreachable" on port 3527 (which I gather is an MQPing packet?). After that, silence. Wireshark shows a nice little stream of packets when I try from my Win7 client (as expected - messages get delivered just fine from Win7). I've enabled MSMQ End2End logging on the server, but only entries from the messages sent from my Win7 machine are appearing in the log. So somehow it seems that messages are being dropped silently somewhere along the route from XP or 2003 to my 2008 server. Does anyone have any clues as to what might be causing this mysterious behaviour? -- Jesper

  Read the article

• Windows 7 not booting after failed SRT (SSD caching) install

  - by david

  This is a fairly new computer, only about a month old. i7 2700k, z68 motherboard, with a 1.5tb WD black HD, and a 128gb crucial M4 ssd. I followed the instructions for setting up ssd caching, the SATA controller was set to RAID, I installed the intel software and enabled acceleration and it said everything went fine. But when I went to reboot, I received the lovely "Reboot and Select proper Boot device" error message. I checked the bios, and it was booting from the correct HD (I tried the only other option anyway just in case, it was the ~50 odd gb of unformatted space left on the SSD) AFter that I entered the raid until (ctrl-i at boot) and removed the acceleration and deleted the raid array (because it was being used as a cache this was non destructive) Still no boot. So I reinstalled win7 directly on the SSD, booted, and checked the HDD to make sure it hadn't been wiped. It hadn't, all the files were still there, including all the windows stuff. I backed up my data to an external drive just in case, but I'd really like to get this install booting again. I trawled the webs a bit, and have tried entering recovery mode and using the bootrec.exe and bootsect.exe to fix it, but to be honest I'm not sure what I'm doing with those. My question is basically: How do I make my harddrive bootable again?

  Read the article

• Ubuntu 12.04 as router with 2 nic

  - by Blue Gene

  I have been trying this setup for weeks and still can not make this to work... ubuntu 12.04 64 bit with 2 nic nic1: eth0:192.168.2.33 -static ip with internet access (connected to modem) nic2: eth1:192.168.1.2 -static ip connected to LAN. enabled ip_forward on ubuntu box net_ip_forward = 1 on the LAN with ip address 192.168.1.5 specified gateway as 192.168.1.2 and able to ping gateway.But can not ping public address.What am i missing? on router box: route -n Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.2.1 0.0.0.0 UG 100 0 0 eth0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 tried ip route add 192.168.2.0/24 via 192.168.1.2 dev eth0 route -n on LAN 192.168.1.5 Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.1.2 0.0.0.0 UG 100 0 0 eth0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.2.0 192.168.1.2 255.255.255.0 UG 0 0 0 eth0 iptables default policy is to accept all. tracepath 8.8.8.8 from LAN 1: 192.168.1.5 0.060ms pmtu 1500 1: 192.168.1.2 3.367ms 1: 192.168.1.2 3.764ms 2: no reply Is there a way to make this work,other than NAT ing.

  Read the article

• openvpn in a bridge?

  - by sebelk

  I have a somewhat tricky proble to solve. We have a wireless link between 2 building. One of them has an mikrotik and below there are some vlans. Some machines of one vlan need to use openvpn to connect to a remote private lan. I put a TP-Link WR1043ND (which those machines connect to) with openwrt with ebtables just in case I need it. I've configured openwrt in such a way that all ports belongs to the same vlan. My idea was to make things as transparent as I can. It has a bridge as follows: usr/sbin/brctl-full show br-lan bridge name bridge id STP enabled interfaces br-lan 8000.f8d111565716 no eth0.1 eth0.2 Also I've added an ebtables rule: ebtables -t broute -A BROUTING -p ipv4 -j DROP So "bridge" has only one IP address. I've installed openvpn and I'm trying to bring up the tunnel but I can't still get working. Sure, someone can says why don't you use the vpn on the mikrotik, there are some reasons, the first one is I have little experience with mikrotik and I'd want to have the vpn at hand :) The problem is that openvpn is not working, because it is complaining that I have only one Ip Address on the server side. So I set up and alias interface with another IP address but is not working either: : Rejected connection attempt from IP-Client-Side:37801 due to --remote setting Is there a way to make it work?

  Read the article

• Is it possible to command a common router without using the web interface?

  - by MDeSchaepmeester

  Some background The internet arrangement in my student home is really weird. There is one ethernet outlet and several wifi hotspots. Either way requires a login through a web site to get internet access. This is annoying as each device needs to login seperately and with a PS3 for example, it is impossible to get connected at all since the web login procedure doesn't work. Therefore I have installed a D-Link DIR-635 router which is connected to the ethernet outlet. It has DHCP enabled so it uses NAT, but whatever it is connected to also uses NAT and I've read this should not work. A fellow student tried it with an Apple Airport but that keeps giving errors related to NAT after NAT. Anyway my setup does work so bonus points if you can clarify this. I need to login to the web site I mentioned earlier with any device, after which all devices in my LAN have connectivity. This is great. Except... In short From time to time, I lose internet connectivity and my D-Link DIR-635 router needs to do a DHCP renew. I can do this via the web interface but my life would be easier if I could just run a cmd file which tells my router to do this without all the hassle. This would setup a connection to my router and execute the proper command. I have tried googling but couldn't find much helpful stuff.

  Read the article

• SMF restarting service whenever there's output?

  - by Phillip Oldham

  I'm trying to add a custom service to SMF's configuration, which seems successful in that the service starts and there is a log file, but therein lies the problem; the service, on start-up, prints some logging messages to the stderr. It seems that SMF is seeing those messages and, believing them to be errors, restarts the service, giving up after a number of tries and leaving the service off. Here's part of the log output: [ Mar 30 14:59:54 Enabled. ] [ Mar 30 14:59:54 Executing start method ("java server.CustomServer"). ] Starting server... [ Mar 30 15:00:04 Method or service exit timed out. Killing contract 107. ] Running the server directly on the commandline is fine, and AFACS there are no errors being encountered during startup, other than the output. What would be the best way to manage this service with SMF? The logging is needed for diagnosing problems, and would be problematic to disable. Is it possible to configure this service to only restart if the service exists?

  Read the article

• RewriteRule causes POST data to get dumped before I can access it

  - by MatthewMcGovern

  I'm currently setting up my own 'webserver' (a Ubuntu Server on some old hardware) so I can have a mess around with PHP and get some experience managing a server. I'm using my own little MVC framework and I've hit a snag... In order for all requests to make it through the dispatcher, I am using: <Directory /var/www/> RewriteEngine On RewriteCond %{REQUEST_URI} !\.(png|jpg|jpeg|bmp|gif|css|js)$ [NC] RewriteRule . HomeProjects/index.php [L] </Directory> Which works great. I read on Stackoverflow to change the [L] to [P] to preserve post data. However, this causes every page to return: Not Found The requested URL <url> was not found on this server. So after some more searching, I found, "Note that you need to enable the proxy module, and the proxy_http_module in the config files for this to work." The problem is, I have no idea how to do this and everything I google has people using examples with virtual hosts and I don't know how to 'translate' that into something useful for my setup. I'm accessing my webserver via my public IP and forwarding traffic on port 80 to the web server (like I'm pretending I have a domain/server). How can I get this enabled/get post data working again? Edit: When I use the following, the server never responds and the page loads indefinately? LoadModule proxy_module /usr/lib/apache2/modules/mod_proxy.so LoadModule proxy_http_module /usr/lib/apache2/modules/mod_proxy_http.so <Directory /var/www/> RewriteEngine On RewriteCond %{HTTP_REFERER} !^http://(.+\.)?82\.6\.150\.51/ [NC] RewriteRule .*\.(jpe?g|gif|bmp|png|jpg)$ /no-hotlink.png [L] RewriteCond %{REQUEST_URI} !\.(png|jpg|jpeg|bmp|gif|css|js)$ [NC] RewriteRule . HomeProjects/index.php [P] </Directory>

  Read the article

< Previous Page | 203 204 205 206 207 208 209 210 211 212 213 214  | Next Page >