Search Results

Search found 8555 results on 343 pages for 'virtualbox networking'.

Page 208/343 | < Previous Page | 204 205 206 207 208 209 210 211 212 213 214 215  | Next Page >

  • Using Lan Management port - which kind of switch for remote control?

    - by zephyrus
    Hello everyone, I have no expertize in server hardware, however i have some IBM X3550 7978 and HP DL 160/G6 servers with 2 Lan ports, and a management port (that seem to be another Lan port). Have anyone tried to use the management to control remotely the low level functions of the servers (reboots for example) ? Which kind of switch or other devices have you used for this? thank you Massimiliano

    Read the article

  • Multiple connections to the same Wireless Network in Windows 7

    - by Jamek
    Hello, my university just limited bandwidth to 512 kbps (that's 64 kB/s!) for each connection. I was thinking to make multiple connection to the same wireless network (called "internet"), is this possible under Windows 7? I know it's possible to connect to more than one WLAN through the "hostednetwork" concept in netsh: netsh wlan set hostednetwork mode=allow ssid=xxxxx netsh wlan start hostednetwork However this method doesn't seem to work, I don't know if it's due to the authentication method (through certificates while hostednetwork seems to support just a "passphrase") or because I'm already connected to that network with the same MAC. Can you think to some tool able to do this?

    Read the article

  • Share PC over network

    - by Sachin Verma
    I have a server installed on one local Win7 machine (say as 192.168.2.14:8080/myAPP) and I want to access that server from different computer (say ip as 192.168.2.16). Even they are connected to same network I can't access server from other computer. I guess the problem is in firewall. This is working when I disable firewall and not working when I allow certain ports in windows firewall but keeping firewall on (As a rule to allow incoming connections).

    Read the article

  • windows cache not working as it should?

    - by piotrektt
    I run windows 2012 server with data center. The setup is with 60GB of RAM. I have one file shared on VHD and when I copy this file locally the RAM cache is all used up but when multiple computers connect to the share it the cache is not used. The network is 8Gb. The whole network is around 200 computers that need to read that one file but on this setup only 10 connection kills the server. Is there any way to check what is going on? What other solution can I use to manage cache in windows?

    Read the article

  • WinXP workgroup, 3 routers 3 computers

    - by Silvera
    I have 3 computers with WinXP x86, and 3 Cisco 1800 series routers. I'm trying to create a workgroup so that the 3 computers can share files with eachother. They can ping eachother (without any internet connection), and the routers setup is correctly configured (with interfaces, ip adresses, and ports). But none of the computers can see eachother, even though they are on the same network. My first question would be - can it be done the way it is currently configured - and, if yes, how, or can anyone point me in the right direction?

    Read the article

  • Troubleshooting my internet connection

    - by Simon Verbeke
    While I was out of the house, my father rearranged the network cables a bit. I don't know what he has done exactly - He says nothing more then pulling and untangling. When I came back home, my internet connection changed its IP from 192.168.0.205 to 169.254.197.233. The speed changed from 1Gbps to 10Mbps. It has also been at 100Mbps for a while. My subnetmask changed from 255.255.255.0 to 255.255.0.0. The standard gateway changed from 192.168.0.1 to no standard gateway. My DNS servers remain the same. I have checked the lights of the UTP ports, and it looks like it's only sending a heartbeat every few seconds. A sketch of the (relevant part of) the network: My PC ----- extender ----- modem ^ ^ ^ Wired | Wired | This thing connects two cables to each other All the cabling is gigabit, my network card is a Realtek RTL8168C(P)/8111(P) Family PCI-E Gigabit Ethernet NIC (NDIS 6.20). THe modem is a CBN SVG6540E I have no idea what is going on here and I don't know how to find out either. Any help is welcome! If you need any more info, please ask.

    Read the article

  • Accessing VMware Player across the network

    - by Tiffany Walker
    My network: 192.168.2.2 (computer) 255.255.255.0 (mask) 192.168.2.254 (gateway) The VMplayer is: 192.168.233.129 (ip) 255.255.255.0 (mask) 192.168.233.255(bcast) It's obvious the player can't be access from other systems because of the wrong network settings. However, I am not sure as to how to change that. Obviously I have to edit the ifcg-eth0 but I know I also need to edit it on the host system to make it accessably. Is this done from inside VMware Player? Or do I need to edit the network devices? The host box is Windows. Inside VMware is Linux.

    Read the article

  • Benefits to private networks between virtual machines on an ESXi host?

    - by arex1337
    I'm planning this development environment with a few database servers, and originally thought I would have a few private networks. I then thought it might be unnecessary as the ESXi cluster already provides redundancy with 4 NICs (in my case) and should manage the network traffic pretty intelligently, right? Two private networks Zero private networks What are the advantages/disadvantages between the two shown configurations - on an ESXi 4.1 host?

    Read the article

  • Maximise network transfer speed of various applications

    - by Alex
    When using nc, scp, wget to transfer files between 2 machines on a dedicated 2Mbps link, I get speeds between 0.5 and 1 Mbps. However, when I use iperf -c 10.0.1.4 -t 20 -P 12 (for example) I can maximise the speed of the link (getting stable 2Mbps). Is there a way to make single stream transfers (such as those done by scp) to utilise all/most of the link? Some kind of tcp settings, or iptables...?

    Read the article

  • Set web browser (or other program) to use specific network

    - by Will
    my PC is connected to 3 different networks: 2 different LAN connections and a VPN connection. when i am connected to the vpn, i cannot browse to the LAN intranet as the DNS is all going through the vpn and it cannot see the domains on the LAN. Is there a way to set firefox/chrome/etc to use a specific connection, so that i don't have to disconnect from vpn to get to the other intranets?

    Read the article

  • Inbound connections to a ubuntu machine running a VPN

    - by shanedowling
    Is it possible to open inbound connections to a machine connected to a VPN server? The machine is running ubuntu 9.10 with two network devices(a wireless card and ethernet port), I can connect to my machine locally using a local ip but when I try port forward using my router I can't connect from my external ip. Is there a way around this? I figure with 2 network devices I can vpn over one and use the other for inbound connections but I can't figure out how to do this. Thanks

    Read the article

  • bridge traffic limiting via tc

    - by jackhab
    I have a Linux machine running as a bridge simulating various network conditions. I use tc for this. Introducing delays or packet loss is quite simple but I got into trouble trying to configure bandwidth limiting. Can you, please, show me how to limit all the traffic going through my bridge without any special rules and condition, simply limit it to 1Mb/s? Thanks. PS Your favorite link to tc tutorial will be appreciated.

    Read the article

  • How can I start hostednetwork on Windows 7?

    - by Pirozek
    When I type in admin console command to start hostednetwork netsh wlan start hostednetwork it gives me this: The hosted network couldn't be started. The group or resource is not in the correct state to perform the requested operation. There is a hotfix from Microsoft but it didn't help me. Any advice? C:\Users\Pirozek>netsh wlan show driver Interface name: Wireless Network Connection 3 Driver : D-Link AirPlus DWL-G520 Wireless PCI Adapter(rev .B) Vendor : Atheros Communications Inc. Provider : Atheros Communications Inc. Date : 8.7.2009 Version : 8.0.0.171 INF file : C:\Windows\INF\oem108.inf Files : 2 total C:\Windows\system32\DRIVERS\athrx.sys C:\Windows\system32\drivers\vwifibus.sys Type : Native Wi-Fi Driver Radio types supported : 802.11b 802.11g FIPS 140-2 mode supported : Yes Hosted network supported : Yes Authentication and cipher supported in infrastructure mode: Open None Open WEP-40bit Shared WEP-40bit Open WEP-104bit Shared WEP-104bit Open WEP Shared WEP WPA-Enterprise TKIP WPA-Personal TKIP WPA2-Enterprise TKIP WPA2-Personal TKIP Vendor defined TKIP WPA2-Enterprise Vendor defined Vendor defined Vendor defined WPA-Enterprise CCMP WPA-Personal CCMP WPA2-Enterprise CCMP Vendor defined CCMP WPA2-Enterprise Vendor defined Vendor defined Vendor defined WPA2-Personal CCMP Authentication and cipher supported in ad-hoc mode: Open None Open WEP-40bit Open WEP-104bit Open WEP WPA2-Personal CCMP

    Read the article

  • Random “Lost connection to MySQL server at 'reading initial communication packet', system error: 0”

    - by user1606545
    Sometimes I get the error from MYSQL server: Lost connection to MySQL server at 'reading initial communication packet', system error: 0 I cannot find the cause, since most of the time it works, but every week for some hours I get this error. I googled, but there seem to be only users which have this error permanently. But in this case, it only occurs sometimes. I checked hosts.allow and hosts.deny, but the host is allowed and not denied. Also sometimes I get the error: File './database/table.MYD' not found (Errcode: 24) It occurs very rarely. But it occurs for some hours once a week, sometimes on multiple days, but suddenly the problem disappears again. I have checked the open files limit. It's 2048 and should be absolutely enough. I also tried to increase the number of open files nevertheless, but no effect. I thought, perhaps the process does not close some tables. But this is impossible, because after a while everythings o.k. again and the process opens maximum 100 tables at once. I also checked the MySQL-runtime-environment, and there were 930 opened files. I cannot explain that. After a while it's 129. I am running a MySQL-Server on a SUSE-Linux machine. I connect to the MySQL-Server from another host by the command line tool "mysql" and by MySQL-C-connector. The MySQL-Server is version 5.0.67.

    Read the article

  • RESOLVED Why does IPtables's NAT stop working when I enable the firewall's third interface?

    - by Kronick
    On my firewall I've three interfaces : eth0 : public IP (46.X.X.X.) eth0:0 public IP (46.X.X.Y.) eth1 : public IP (88.X.X.X.) eth2 : private LAN (172.X.X.X) I've setup a basic NAT which works great until I turn on the eth1 interface, I basically loose the connectivity. When I turn off the interface (ifconfig eth1 down) then the NAT re-work. I've added some policy routing via iproute, which makes my three public IP's available. I don't understand why turning on eth1 on makes the LAN unavailable. PS : weirder ; when I turn on eth1 BUT remove the NAT, then the firewall is accessible by using the public IPS. So to me it's exclusively a NAT issue, since without the NAT the network works while with the NAT without the second public interface, the NAT does work. Regards EDIT : I've been able to make it work by using iproute2 rules. That was definitely a routing issue. Here is what I did : ip rule add prio 50 table main ip rule add prio 201 from ip1/netmask table 201 ip rule add prio 202 from ip2/netmask table 202 ip route add default via gateway1 dev interface1 src ip1 proto static table 201 ip route append prohibit default table 201 metric 1 proto static ip route add default via gateway2 dev interface2 src ip2 proto static table 202 ip route append prohibit default table 202 metric 1 proto static # mutipath ip rule add prio 221 table 221 ip route add default table 221 proto static \ nexthop via gateway1 dev interface1 weight 2\ nexthop via gateway2 dev interface2 weight 3

    Read the article

  • How to know my wireless card has injection enabled?

    - by shrimpy
    I am playing around with aircrack. And was trying to see whether my wireless card on my laptop can pass the injection test And I end up seeing the following... does it mean my wireless card is not able to run aircrack? root@myubuntu:/home/myubuntu# iwconfig lo no wireless extensions. eth0 no wireless extensions. eth1 IEEE 802.11bg ESSID:"" Nickname:"" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Bit Rate:54 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=5/5 Signal level=0 dBm Noise level=-57 dBm Rx invalid nwid:0 Rx invalid crypt:781 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 root@myubuntu:/home/myubuntu# aireplay-ng -9 eth1 ioctl(SIOCSIWMODE) failed: Invalid argument ARP linktype is set to 1 (Ethernet) - expected ARPHRD_IEEE80211, ARPHRD_IEEE80211_FULL or ARPHRD_IEEE80211_PRISM instead. Make sure RFMON is enabled: run 'airmon-ng start eth1 <#>' Sysfs injection support was not found either. root@myubuntu:/home/myubuntu#

    Read the article

  • How many megabytes per second may I expect from a gigabit USB 2.0 network card under linux?

    - by Nakedible
    I'm interested in the actual real-word throughput attainable with an external 1000BaseT USB 2.0 network card under Linux. I have been able to attain 90 megabytes per second on a PCI-E interface, but the USB 2.0 bus has a theoretical limit of 480Mbit/s, and in practice less than 40 megabytes per second. Is the actual throughput attainable with such a card under linux 40, 30, 20, or even as low as 10 megabytes per second, eg. no better than a normal 100BaseT network card?

    Read the article

  • How do I bridge a connection from Wi-Fi to TAP on Mac OS X? (for the emulator QEMU)

    - by penx
    I'm trying to setup a bridge between my Wi-Fi connection and an emulator (QEMU). I need a virtual machine to be on the same LAN as the host, with its own IP address. QEMU requires using a TAP (virtual network device) so I have installed tuntaposx, have it running, and can open up QEMU using a TAP: qemu-system-arm -kernel zImage.integrator -initrd arm_root.img -m 256 -net nic -net tap,ifname=tap1 -nographic -append "console=ttyAMA0" I have a script that configures the bridge once QEMU has opened up the TAP interface: sysctl -w net.link.ether.inet.proxyall=1 sysctl -w net.inet.ip.forwarding=1 sysctl -w net.inet.ip.fw.enable=1 ifconfig bridge0 create ifconfig bridge0 addm en1 ifconfig tap1 0.0.0.0 up ifconfig bridge0 addm tap1 ifconfig bridge0 up If I manually set an IP on the VM, I can ping from the VM to the host, but not from the host to the VM. Also, I can't access the rest of the network from the VM - including not being able to set an IP over DHCP. Any ideas?

    Read the article

  • WAN Optimization for Small Office/Home Office

    - by TiernanO
    I have been reading up on WAN optimization for the last while, mostly out of interest of speeding up my own internet connections, but also to speed up the office internet connection. At home, I have 2 cable modems plugged into a RouterBoard RB750, which load balances the connections. In the office, we have a single connection into a NetGear router. Most of the WAN Optimization products I have seen, seem to be prohibitively expensive, but also seem to be based on the idea of having multiple branches around the world. What I am looking for, ideally, is as follows: software install: I am "guessing" I need to install it in 2 places: one in the office or house, and one in "the cloud". any connections going to, say, The US (we are in Europe, but our backup's live in the US currently, which would be something important to speed up) would be "tunnelled" though the Optimizer. If downloading or uploading large files, open multiple connections between both "the cloud" and the optimizer... This is where a lot of speed could be gained. finally, for items not compressed, they would be compressed on the cloud side of things, also items that are already on the optimizer could be not sent again. kind of like RSync or Proxy servers... So, is there something that can be done? Is it available using off the shelf components (some magic script with SSH, Squid, Linux and duct tape) or is it something that needs to be purchased? or even an Open Source Project that does 90% of what i am asking?

    Read the article

  • How can I make VNC faster?

    - by NickAldwin
    I need to remotely access and use my work computer a few times a week. I want to use VNC because of the price. I've used VNC before, mostly on my own network, where it's fast. However, VNC over the internet is incredibly slow. Even at 256 colors and lower, with Aero turned off, it is unbearably slow. I recently used Ammyy Admin to connect to do something requiring a quick reaction time. Ammyy was really fast, with almost no lag, and it was running in full color with Aero on! How can I make VNC faster, like Ammyy is? I'd use Ammyy, but I would probably run into the 15hr/month limit pretty quickly. Any suggestions? [EDIT] I'm currently using UltraVNC.

    Read the article

  • Windows 7 laptop with two active network connections will not perform DNS AAAA lookup under certain conditions

    - by Jeff Loughridge
    My laptop has two network interfaces. The Ethernet interface connects directly to my provider's edge router. It obtains an IPv6 address via SLAAC. I manually set an IPv6 DNS server. The wireless interface connects to a CPE router that doesn't understand IPv6. If the wireless interface is disabled, I can reach the IPv6 Internet with no problems using the Ethernet interface. I run into problems when both interfaces are enabled and the wireless interface get its IPv4 DNS server via DHCP. Let's look at two scenarios. Wireless interface obtains IPv4 DNS server via DHCP - The CPE router (192.168.0.1) sends its address as the DNS server. In this scenario, Windows 7 will not perform AAAA lookups. The browser uses IPv4 transit to reach dual stack web sites. I can't reach IPv6-only web sites using domain names. I can reach IPv6-enabled web sites using IPv6 literals instead of the domain name. Wireless interface is manually configured with OpenDNS DNS server - Windows 7 performs AAAA lookups using IPv6 transit (via the Ethernet). Everything works fine. My dual homed set-up is definitely not standard. Still, the behavior is very strange to me. A valid IPv6 interface exists in my Ethernet interface. Why won't Windows attempt AAAA lookups in scenario #1? I've included the output of ipconfig /all and netstat -rn. C:\Program Files\Console>ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : jake Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : res.openband.net Wireless LAN adapter Wireless Network Connection 2: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Microsoft Virtual WiFi Miniport Adapter Physical Address. . . . . . . . . : C0-CB-38-06-54-F9 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : res.openband.net Description . . . . . . . . . . . : DW1520 Wireless-N WLAN Half-Mini Card Physical Address. . . . . . . . . : C0-CB-38-06-54-F9 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::fc39:9293:7d01:4a75%13(Preferred) IPv4 Address. . . . . . . . . . . : 192.168.0.105(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : Wednesday, July 11, 2012 7:35:21 AM Lease Expires . . . . . . . . . . : Thursday, July 12, 2012 9:49:46 AM Default Gateway . . . . . . . . . : 192.168.0.1 DHCP Server . . . . . . . . . . . : 192.168.0.1 DHCPv6 IAID . . . . . . . . . . . : 364956472 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-17-80-F8-14-5C-26-0A-03-23-5C DNS Servers . . . . . . . . . . . : 208.67.222.222 NetBIOS over Tcpip. . . . . . . . : Enabled Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : res.openband.net Description . . . . . . . . . . . : Intel(R) 82577LM Gigabit Network Connection Physical Address. . . . . . . . . : 5C-26-0A-03-23-5C DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IPv6 Address. . . . . . . . . . . : 2607:2600:1:850:c0e9:211a:fd05:4e0b(Preferred) Temporary IPv6 Address. . . . . . : 2607:2600:1:850:3d29:1839:62db:c4c1(Preferred) Link-local IPv6 Address . . . . . : fe80::c0e9:211a:fd05:4e0b%12(Preferred) IPv4 Address. . . . . . . . . . . : 10.52.2.51(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.254.0 Lease Obtained. . . . . . . . . . : Monday, July 09, 2012 8:55:07 AM Lease Expires . . . . . . . . . . : Thursday, July 12, 2012 7:30:05 AM Default Gateway . . . . . . . . . : fe80::214:6aff:fe51:7f3f%12 10.52.2.1 DHCP Server . . . . . . . . . . . : 216.40.77.244 DNS Servers . . . . . . . . . . . : 2620:0:ccc::2 2620:0:ccd::2 216.40.77.126 216.40.77.244 NetBIOS over Tcpip. . . . . . . . : Enabled Ethernet adapter VMware Network Adapter VMnet1: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : VMware Virtual Ethernet Adapter for VMnet1 Physical Address. . . . . . . . . : 00-50-56-C0-00-01 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::4c61:495b:229e:281e%14(Preferred) IPv4 Address. . . . . . . . . . . : 192.168.40.1(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : DHCPv6 IAID . . . . . . . . . . . : 469782614 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-17-80-F8-14-5C-26-0A-03-23-5C DNS Servers . . . . . . . . . . . : fec0:0:0:ffff::1%1 fec0:0:0:ffff::2%1 fec0:0:0:ffff::3%1 NetBIOS over Tcpip. . . . . . . . : Enabled Ethernet adapter VMware Network Adapter VMnet8: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : VMware Virtual Ethernet Adapter for VMnet8 Physical Address. . . . . . . . . : 00-50-56-C0-00-08 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::f996:61eb:8c00:45e6%15(Preferred) IPv4 Address. . . . . . . . . . . : 192.168.17.1(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : DHCPv6 IAID . . . . . . . . . . . : 486559830 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-17-80-F8-14-5C-26-0A-03-23-5C DNS Servers . . . . . . . . . . . : fec0:0:0:ffff::1%1 fec0:0:0:ffff::2%1 fec0:0:0:ffff::3%1 NetBIOS over Tcpip. . . . . . . . : Enabled C:\Program Files\Console>netstat -rn =========================================================================== Interface List 17...c0 cb 38 06 54 f9 ......Microsoft Virtual WiFi Miniport Adapter 13...c0 cb 38 06 54 f9 ......DW1520 Wireless-N WLAN Half-Mini Card 12...5c 26 0a 03 23 5c ......Intel(R) 82577LM Gigabit Network Connection 11...5c ac 4c f8 b8 55 ......Bluetooth Device (Personal Area Network) 14...00 50 56 c0 00 01 ......VMware Virtual Ethernet Adapter for VMnet1 15...00 50 56 c0 00 08 ......VMware Virtual Ethernet Adapter for VMnet8 1...........................Software Loopback Interface 1 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.52.2.1 10.52.2.51 10 0.0.0.0 0.0.0.0 192.168.0.1 192.168.0.105 100 10.52.2.0 255.255.254.0 On-link 10.52.2.51 261 10.52.2.51 255.255.255.255 On-link 10.52.2.51 261 10.52.3.255 255.255.255.255 On-link 10.52.2.51 261 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.0.0 255.255.255.0 On-link 192.168.0.105 306 192.168.0.105 255.255.255.255 On-link 192.168.0.105 306 192.168.0.255 255.255.255.255 On-link 192.168.0.105 306 192.168.17.0 255.255.255.0 On-link 192.168.17.1 276 192.168.17.1 255.255.255.255 On-link 192.168.17.1 276 192.168.17.255 255.255.255.255 On-link 192.168.17.1 276 192.168.40.0 255.255.255.0 On-link 192.168.40.1 276 192.168.40.1 255.255.255.255 On-link 192.168.40.1 276 192.168.40.255 255.255.255.255 On-link 192.168.40.1 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 10.52.2.51 261 224.0.0.0 240.0.0.0 On-link 192.168.0.105 306 224.0.0.0 240.0.0.0 On-link 192.168.40.1 276 224.0.0.0 240.0.0.0 On-link 192.168.17.1 276 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 10.52.2.51 261 255.255.255.255 255.255.255.255 On-link 192.168.0.105 306 255.255.255.255 255.255.255.255 On-link 192.168.40.1 276 255.255.255.255 255.255.255.255 On-link 192.168.17.1 276 =========================================================================== Persistent Routes: None IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 12 261 ::/0 fe80::214:6aff:fe51:7f3f 1 306 ::1/128 On-link 12 13 2607:2600:1:850::/64 On-link 12 261 2607:2600:1:850:3d29:1839:62db:c4c1/128 On-link 12 261 2607:2600:1:850:c0e9:211a:fd05:4e0b/128 On-link 12 261 fe80::/64 On-link 13 281 fe80::/64 On-link 14 276 fe80::/64 On-link 15 276 fe80::/64 On-link 14 276 fe80::4c61:495b:229e:281e/128 On-link 12 261 fe80::c0e9:211a:fd05:4e0b/128 On-link 15 276 fe80::f996:61eb:8c00:45e6/128 On-link 13 281 fe80::fc39:9293:7d01:4a75/128 On-link 1 306 ff00::/8 On-link 12 261 ff00::/8 On-link 13 281 ff00::/8 On-link 14 276 ff00::/8 On-link 15 276 ff00::/8 On-link =========================================================================== Persistent Routes: None

    Read the article

  • Concurrent wireless and wired network

    - by Stew Megaw
    Hi, I am concerned with maintaining a wireless and wired network connection on my laptop. Basically I can change the metric on each interface so that Windows prefers one connection over the other. I am wondering is following scenario possible.... Some applications uses the wireless while other applications use the wired... I want Internet Explorer (only) to use the wireless connection while Outlook and everything else uses the wired connection. Perhaps adding some lines to the routing table might work? - Adding the ip addresses of websites I want to view via the wireless connection? Many Thanks in advance for any replies!

    Read the article

  • good PCI-e Wireless card for Windows7?

    - by benwebdev
    Hi I've just build a 64bit Windows 7 PC but am unhappy with the piddly performance of the linksys USB wireless dingle I've used. Can anyone suggest a good PCIe alternative that will be stronger for connection and maybe faster. I dont see why my desktop should show a weaker performance on wireless than my laptop when its sat next to it or even my Palm Pre for that matter. any thoughts? UK based max around £60ish. thanks, Ben

    Read the article

  • How can I set my TP-Link TL-WR1043ND to extend my router - modem range?

    - by Pitto
    I'd like to extend my WiFi coverage, so I've bought the TP-Link TL-WR1043ND and updated its firmware to the latest (wr1043nv1_en_3_13_4_up(110429)) but I can't find how to use its WDS function. Reading further on Super User I understand that both the modem-router (Pirelli Alice Gate) and the TL-WR1043ND should support WDS. Are there any tricks to achieve the same result - extending my WiFi range - even changing the firmware to DD-WRT or Tomato etc?

    Read the article

  • TCP/IP communication between Hyper-V host and guests

    - by Tedd Hansen
    This may be a simple one. :) I have a simple Hyper-V setup with a few guest os running. The host has 1 physical network adapter with a static IP assigned to it. The guests have network adapters assigned to "Internet" (Hyper-V network) which is bound to the physical host network adapter (Hyper-V "External" connection type). I am not able to communicate (ping or anything else) between guests and host. I've checked firewall and it seems fine (ports open from anywhere still don't work). I'm trying to communicate with the hosts IP assigned to the same physical interface that the guests are sharing. Guests can communicate between them just fine. I can't seem to find any relevant setting (I might just be missing it). So my questions: How do I fix it so host and guests can communicate?

    Read the article

< Previous Page | 204 205 206 207 208 209 210 211 212 213 214 215  | Next Page >