Search Results

Search found 6922 results on 277 pages for 'moving platforms'.

Page 209/277 | < Previous Page | 205 206 207 208 209 210 211 212 213 214 215 216  | Next Page >

  • Can a pool of memcache daemons be used to share sessions more efficiently?

    - by Tom
    We are moving from a 1 webserver setup to a two webserver setup and I need to start sharing PHP sessions between the two load balanced machines. We already have memcached installed (and started) and so I was pleasantly surprized that I could accomplish sharing sessions between the new servers by changing only 3 lines in the php.ini file (the session.save_handler and session.save_path): I replaced: session.save_handler = files with: session.save_handler = memcache Then on the master webserver I set the session.save_path to point to localhost: session.save_path="tcp://localhost:11211" and on the slave webserver I set the session.save_path to point to the master: session.save_path="tcp://192.168.0.1:11211" Job done, I tested it and it works. But... Obviously using memcache means the sessions are in RAM and will be lost if a machine is rebooted or the memcache daemon crashes - I'm a little concerned by this but I am a bit more worried about the network traffic between the two webservers (especially as we scale up) because whenever someone is load balanced to the slave webserver their sessions will be fetched across the network from the master webserver. I was wondering if I could define two save_paths so the machines look in their own session storage before using the network. For example: Master: session.save_path="tcp://localhost:11211, tcp://192.168.0.2:11211" Slave: session.save_path="tcp://localhost:11211, tcp://192.168.0.1:11211" Would this successfully share sessions across the servers AND help performance? i.e save network traffic 50% of the time. Or is this technique only for failovers (e.g. when one memcache daemon is unreachable)? Note: I'm not really asking specifically about memcache replication - more about whether the PHP memcache client can peak inside each memcache daemon in a pool, return a session if it finds one and only create a new session if it doesn't find one in all the stores. As I'm writing this I'm thinking I'm asking a bit much from PHP, lol... Assume: no sticky-sessions, round-robin load balancing, LAMP servers.

    Read the article

  • Random Excel bug when referencing a different sheet

    - by Matteo
    I am getting a very strange error anytime I try to use a formula pointing to a cell in a different sheet from the active one (even as simple as "=Sheet2!A1"). This started happening all of a sudden, and without any change in the system - only I seem to having started having the problem since I started using a workbook from another colleague with the same issue. I'm running Excel 2003 SP3 on XP. With little variants, whenever I reference a cell in a different sheet, from any formula, and then press Enter, the formula gets written on a different cell from the one I was editing it in, and throws a REF error. Example: I start editing in cell A1 of Sheet 1, type "=", then move the cursor to cell B2 of Sheet 2 (that may contain any value), and press Enter. At this stage you would expect cell A1 in Sheet 1 to contain formula "=Sheet2!B2" and display the value in that cell. Instead what happens is that the cell remains empty, and another random cell of Sheet 1 gets populated with something like "=Sheet2!#REF!" throwing an error. Interestingly, the error does not happen when I manually type the cell reference in (ie. without moving the cursor to the second sheet). Hope this is making any sense - any ideas are welcome! Thanks.

    Read the article

  • Outbound mail issue during Exchange 2003 migration

    - by user27574
    Dear all, I am having an outbound email issue during the Exch 03 migration. Basically, we are migrating Exch03 to new hardware, both servers are Server 03 based. Everything runs smooth while setting up and installing Exch 03 on the new box. Public folders are all replicated. My issues are shown below.... 1) After starting to move users' mailboxes to new Exch 03, they receive some undeliverable mail and bounced back mail from some vendors, then I move few users back to test around, they have no problem at all after moving back to old Exch 03. 2) Another issue is our company has Blackberry users, we don't have BES. Under each user's mailboxes, we have forward rule setup, so that both user inbox and BB can receive email. User who is moved to the new Exch 03 server, they can only send email to the BB user's inbox, mail cannot be forwarded to BB at all, smtp queue stacks up and keep trying until the time is expired. Since not all emails that the users send out from the new Exch have problem, I am not able to narrow down what is the issue here. Can anyone give me some ideas? Could this be MX record / Reversed DNS relate? Or firewall NAT rule setting? Thanks.

    Read the article

  • What is a long-term strategy to deal with CPU fan dust in my home office?

    - by PaulG
    There are numerous discussions of CPU overheating and how sometimes this can be corrected by removing the dust from the CPU fan. I have read many of these, but I can't find anyone expressing a long-term strategy to deal with this problem. There are some suggestions here, for example, about how often the inside of the computer should be dusted. But I find this generally unsatisfactory. As it stands, in my rather dusty house (heated by a wood stove, with no central air circulation), I need to vacuum out the CPU fan every 3 to 4 months. At high CPU load, this can make a difference between 65C and 100C. I'm tired of hauling out the vacuum every time I anticipate high CPU load. What steps can I take to deal with this systematically in the long-term? Moving my high CPU load computing to the cloud is not a realistic option. Neither is vacuuming my home office more than once a week! (Details: my computer is on the floor in a Cooler Master HAF922 case, and uses an Intel CPU fan on an i7 chip) EDIT: While this would definitely solve the problem (submerging motherboard in mineral oil), it is a bit of an expensive solution.

    Read the article

  • SUSE Linux and Xen on Mac Pro - How best to prepare and configure?

    - by Andrew J. Brehm
    This is a longwinded question, so bear with me please. I have a 2009 Mac Pro with two CPUs and 8 GB of memory which is totally overpowered for Mac OS X. I am also in the process of slowly moving away from Mac OS X as my main platform. Since the Mac Pro is really new and nice I have finally decided to use it for another platform. I am familiar with Linux and SUSE Linux. Ultimately I want to run some version of SUSE Linux (recommend one, doesn't have to be free as in no money) and Xen. Here are the individual questions: Which version of SUSE Linux should I use and how do I install it on a Mac Pro? Note that the distribution must come with usable Xen. I am willing to pay. I assume Xen will work on my computer (it has VT support etc.). Is my assumption correct? I want to run Windows 7 and another instance of SUSE Linux under Xen. Is it possible to run Mac OS X Server under Xen (on a Mac Pro)? Which email client under Linux supports imap is is best-suited for integrating with MobileMe? Does SUSE Linux support the ATI Radeon HD 4870 and the Apple Cinema Display 1920 x 1200 resolution? What else should I take into account?

    Read the article

  • Adding a Printer to my Print Server Failing

    - by Rudi Kershaw
    So, on the Windows Server page I read the following. Step 4: Add Network Printers Automatically Print Management (Printmanagement.msc) can automatically detect all the printers that are located on the same subnet as the computer on which you are running Print Management, install the appropriate printer drivers, set up the queues, and share the printers. To automatically add network printers to a printer server Open the Administrative Tools folder, and then double-click Print Management. In the Printer Management tree, right-click the appropriate server, and then click Add Printer. On the Printer Installation page of the Network Printer Installation Wizard, click Search the network for printers, and then click Next. If prompted, specify which driver to install for the printer. So, I have got to this point, made sure the printer (Canon MP620) is on and correctly plugged into the network. However, when I click "Search the network for printers", the wizard doesn't find it. Now, I can't get any further. Is there anything I could be doing wrong? How should I proceed moving forwards?

    Read the article

  • windows 7 update freeze - what to do?

    - by Tom Tom
    Hi, yesterday I shuted down my notebook and windows 7 Ultimate started to install the automatic update. After one hour I noticed that the update is still running. I thought ok, I go to sleep and let it run. In the morning it was still running. Thus I thought it is crashed. Forced a shut-down of the notebook, and restarted it. With the same effect that the notebook is "freezing" at "Install Update 1 of 5". It does not look like whether it is chrased. The progress wheel is still moving. But it does not make any progres.. Thus somehow like crashed. Would appreciate any help! Edit: Ok was able to log-in in "save" (german: abgesicherter) mode. This way I passed to install update screen. I do not want to generally disable updates. What can I do to not install the last update, which is creating troube. Or how can I find out whats the problem with the last update? Edit2: Ok starting in save mode and finally installing the updates manually solved the problem.

    Read the article

  • Why is my second monitor not working?

    - by StampedeXV
    Since I have my new computer, I have a very weird problem. Facts: New Computer: Motherboard: ASRock Z77 Pro 3 Graphics-card: Asus1GB D5 X EN GTX560 DCII OC/2DI R CPU: Intel i5-3570 Windows 7 64bit 500W beQuiet special edition (92% efficiency) 8GB 1333MHz DDR3 Corsair RAM (CL9) Scythe Mugen 2 2 magnetic HDDs + 1 SDD 1 DVD-R Old Computer: Motherboard: Asus P55 something Graphics-card: Asus1GB D5 X EN GTX560 DCII OC/2DI R CPU: Intel i7-870 Windows 7 64bit 550W Corsair 8GB 1333MHz DDR3 Corsair RAM (CL9) Scythe Mugen 3 2 magnetic HDDs + 1 SDD 1 DVD-R On the old computer it worked fine with two monitors. Moving to the new (I took the same Graphics-card) it only works with one. The weird thing I mentioned is: not matter which one. But if I put both there, only one is available. There is no reaction at the start (where normally (at least if I remember correctly) the monitor shortly went from "standby" to "on"). Windows does not recognize a second monitor in the Device Manager. I have the latest drivers for Motherboard and Graphics-card. I have the latest BIOS drivers. I am out of ideas. Edit: completed computer setup

    Read the article

  • How to publish internal data to the internet - as simple as possible

    - by mlarsen
    I Asked this at Staock Overflow, but I would like your oppinion too as it has as much to do with administration as it does with coding. We have a .net 2-tier application where a desktop program is talking to a database. We support MS SQL Server 2000, 2005, 2008 and Oracle 9, 10 and 11. The application is sold, not as shrink-wrap, but pretty close. It is quite important for us that the installation and configuration is as easy as possible as installation instructions are usually supplied in written form to the customers internal IT-department. Our application is usually not seen as mission critical for the IT-department, so we need to keep their work down to a minimum. Now we are starting to get wishes for a web application build on top of the same data. The web application will be hosted by us and delivered as a SaaS application. Now the challenge is how to move data back and forth between the web application and the customers internal database. as I see it we have some requirements: We must be ready to handle the situation where the customers database is not accessible from the DMZ. I guess the easiest solution is that all communication is initiated from inside the customers lan. As little firewall configuration as possible. The best is if we can run without any special configuration as long as outgoing traffic from the customers lan are not blocked. If we need something changed in the firewall, we must be able to document that the change is secure. It doesn't have to be real time. Moving data in batches every ten minutes or so is OK. Data moves both ways, but not the same tables, so we don't have to support merges. It would be nice if we don't have to roll our own framework completely. Looking forward to hear your suggestions.

    Read the article

  • Comprehensive solution for managing patches, event viewing, change management, inventory, etc

    - by Holocryptic
    I'm looking for a solution that incorporates most or all of the following: Patch Management, Server event viewing/tracking, AD change management, ticketing and internal/external kb, remote access - ability to shadow user sessions or create new ones, imaging, and inventory. Our environments contains Windows Servers and ESXi Hosts (We're not completely virtual, but we're moving that direction). Various Cisco and Linksys switches and firewalls. This is a tall order, and I don't know if it can be done on a reasonable budget. I've looked and found some questions on SF that deal with some of this: http://serverfault.com/questions/72015/active-directory-management-tools-for-medium-sized-forest-less-than-1000-users http://serverfault.com/questions/4021/are-there-any-tools-to-do-change-management-with-active-directory-group-policy http://serverfault.com/questions/21752/what-is-a-good-patch-update-management-server What I'm ideally looking for is a reasonably cheap solution that integrates the features into a central interface. We're a non-profit, so money is a limiting factor (the cheaper, the better; but we have a max of $15k). What we are trying to avoid is having to deal with multiple vendors, while maintaining scalability (we're creating more sites that we'll have to manage). Is this possible, or will we have to cobble together something to make it work for us?

    Read the article

  • Switching between taskbar tasks sequentially

    - by Doug Kavendek
    In Firefox and some other tabbed interfaces, I can use Ctrl-PgUp/Down to cycle through tabs sequentially, based on their order in the tab list. I associate what is what based almost entirely on its position along the tab bar and what is next to what, so this is extremely useful for the way I keep track of things in my head. However, I haven't been able to find an equivalent for actual taskbar items in Windows, such that with a single shortcut will switch focus to the task item either to the left or the right of the current task in focus. There's a lot of existing shortcuts that I use (Alt-Tab, Ctrl-Esc, and their counterparts), but these use the window manager's stacking order, so it always changes based on what you've switched between in the past, and so their usefulness generally only lies in switching between two apps -- above that, I just can't keep that kind of stack in my head. The closest shortcut I've found is Winlogo-Tab, but it only moves a selector on the taskbar, so you have to hit space after moving it, and it also seems to originate the selector from the leftmost item every time (rather than relative to the current item). Am I just a weirdo and will have to write my own app to perform these actions?

    Read the article

  • nginx config woes for multiple subdomains & domains

    - by Peter Hanneman
    I'm finally moving away from Apache and I've got the latest development version of nginx running on a fully updated Ubuntu 10.04 VPS. I've got a single dedicated IP for the box (1.2.3.4) but I've got two separate domains pointing to the server: www.example1.com and www.example2.net. I would like to map the fallowing relationships between urls and document roots in the config: www.example1.com / example1.com -> /var/www/pub/example1.com/ subdomain.example1.com -> /var/www/dev/subdomain/example1.com/ www.example2.net / example2.net -> /var/www/pub/example2.net/ subdomain.example2.net -> /var/www/dev/subdomain/example2.net/ Where the name of the requested subdomain is a folder under /var/www/dev/. Ideally a request for a non-existent subdomain(no matching folder found) would result in a rewrite to the public site (eg: invalid.example1.com -- www.example1.com) however a mere "404 Not Found" wouldn't be the worst thing in the world. It would also be nice if I didn't need to modify the config every time I mkdir a new subdomain folder - even better if I don't need to edit it for a new domain either...but now I'm getting greedy... :p Although in my defense Apache did all of this with a single directive. Does anyone know how I can efficiently mimic this behavior in nginx? Thanks in advance, Peter Hanneman

    Read the article

  • Bad Intel DQ965GF motherboard? Fails memtest, but memory is good.

    - by Boden
    I've got a machine with a DQ965GF motherboard. Two days ago it started locking up hard. Ran memtest 3.3, 1.7, and TestMem 4. TestMem just freezes, memtest failed on moving 8 bit inversions. Letting memtest run eventually causes the system to restart. I pulled memory sticks one by one, and then replaced the memory with a couple of known good sticks. No luck. I switched power supplies, didn't help. Swapped video cards just to be safe. No help. When I start the machine I get a single beep before it POSTs. According to the manual, a single beep means: 1 beep - Refresh Error (with nothing on the screen and it is not a video problem) I'm assuming that the motherboard has failed since it's obviously not a RAM or power issue. Do you agree? NOTE: I also tried resetting BIOS defaults, and even flashed the BIOS to the latest version. I also ran the Mersenne Prime Test and the CPU seems to click along just fine. (Tried logging in to superuser with openid but it's not working for me today. Hope this gets through)

    Read the article

  • Looking for Remote Control that works with everything (even Windows 7 Media Center)

    - by T Reddy
    Using my Google-Fu, it seems that the most basic of things one gets with any DVR is the remote control. Had I known it would be difficult just to get a consumer IR receiver for Windows 7 I may not have bothered to build an HTPC. But too late, I already have the HTPC ready to go (minus the CETON card...) So I'm moving away from TiVo, I hate paying the monthly fees and my box is ancient. I'm looking for these solutions to my HTCP setup...I want to: Switch audio from HDMI to SPDIF via the remote control (i.e., switch from TV to Receiver) (as a side note, the built-in audio on the mobo has software to do this). Pressing the volume button on the remote will always change the TV's volume (or the Receiver's if possible) and NOT the PC's volume. The remote/receiver works well around 25 feet. Bonus if the IR Receiver can work with my existing TiVo remote (or other remotes laying around the house) I read a review of the Bluetooth TiVo remote...it sounds promising...but I'm not sure if it is great for Windows 7 HTPC?

    Read the article

  • Exchange 2010 CAS Removal == Broken???

    - by Doug
    Hi there, I recently upgraded to exchange 2010 and have a setup with 2 of my servers running CAS roles - EXCH01, EXCH02 EXCH02 just happens to also have a mailbox role where a lot of the users sit EXCH01 is my front facing CAS server, and is facing the net with SSL etc and incoming mail moving through it as a hub transport layer server as well. As i was trying to lean things out in my VM environment i removed the CAS role from EXCH02 and all hell broke loose. All the mail users that have a mailbox on EXCH02 had their homeMTA set to a deleted items folder in AD and so did their msExchHomeServer properties. After a complete battle i manually fixed these issues to the oldvalues, and in the mean time reinstalled CAS on EXCH02 (management was going nuts with out OUTLOOK working so i just put things back the way they were in a hurry.) I must add as a strange thing on the side, that before i reset these to point at EXCH02 i tried EXCH01 and it failed. I still want to remove the CAS role from EXCH02 as it should really not have it (error on install/planning on my part) and would have thought that this would not cause the issues it did, i assumed that the fact that there was another CAS server in the admin group all would be good. Was i wrong in my assumption? and what can i do to complete this successfully the second time round? Do i need to rehome all the mailboxes to the CAS server? is this a bug in the role uninstall?

    Read the article

  • This .mpg video clip doesn't play well

    - by Roey
    I've installed K-lite mega codec pack v6.9.0 with playback essentials without player. My default and only media player is windows media player. here are the clip's media info: General Complete name : D:\Users\Roey\Downloads\B384MV.mpg Format : MPEG-PS File size : 273 MiB Duration : 4mn 59s Overall bit rate : 7 643 Kbps Video ID : 224 (0xE0) Format : MPEG Video Format version : Version 2 Format profile : Main@High Format settings, BVOP : No Format settings, Matrix : Default Format settings, GOP : M=1, N=15 Duration : 4mn 57s Bit rate mode : Variable Bit rate : 7 363 Kbps Nominal bit rate : 9 000 Kbps Width : 1 920 pixels Height : 1 080 pixels Display aspect ratio : 16:9 Frame rate : 25.000 fps Color space : YUV Chroma subsampling : 4:2:0 Bit depth : 8 bits Scan type : Progressive Compression mode : Lossy Bits/(Pixel*Frame) : 0.142 Stream size : 261 MiB (96%) Audio ID : 192 (0xC0) Format : MPEG Audio Format version : Version 1 Format profile : Layer 3 Mode : Joint stereo Duration : 4mn 59s Bit rate mode : Constant Bit rate : 128 Kbps Channel(s) : 2 channels Sampling rate : 44.1 KHz Compression mode : Lossy Stream size : 4.56 MiB (2%) Menu When I play it there is no sound (just a little "kahhhh" noise every 10-20 seconds) and the frames are moving very slow - it "jumps" frames. A blue tray icon [FFa] "ffdshow audio decoder" pops with the following details: Input:MP3, stereo, 44100 Hz (libavocodec) Output:PCM, stereo, 44100 Hz, 16-bit integer Any help will be much appreciated. Thanks

    Read the article

  • Why can't I physically access my machine after a remote session?

    - by Steve Crane
    I have a Dell Optiplex 960 desktop running Windows 7 64-bit at work. I typically leave it locked rather than logged off when I go home, so that I'm able to remote in from home and continue working if I wish. This is where the problem comes in. If I don't remote in there is no problem and I can simply unlock the next morning. It's when I do remote in that I have a problem. Remote sessions work as expected but when I get to work the next morning the machine appears to have gone into a sleep or hibernate state, from which no amount of mouse moving or keyboard pounding will wake it. The machine is not hanging as remote sessions to it are still possible; it seems that physical access from it's own mouse and keyboard are lost. The only way to gain access is to press and hold the power switch for several seconds until the machine shuts down. Of course this means Windows does not gracefully shut down and after powering up it takes several minutes for the machine to boot and reach the login prompt; presumably while it checks the disk. Has anyone else seen something like this?

    Read the article

  • Permanently deleting files on Mac OS

    - by Jonik
    A while back, as relatively new Mac OS X user, I was surprised to learn that you cannot easily delete files. Directly, that is, without moving them to the trash first. On Windows and Linux this can obviously be done with ease, but not so on the Mac. I noticed this when trying clear up files from a USB memory stick — removing the files ("move to trash") does not free up space; that happens only after emptying the whole system-wide Trash. Not particularly convenient! (It seems stupid to have to empty the whole trashcan just to make some space on the USB stick. There might be gigabytes of stuff in there, and this sort of defeats its purpose - what if you'd actually need to restore something from the trash some day.) So, what's your way of getting around this? Have you bought a 3rd party application like RAW Trash for $16.95 just to delete files, or do you diligently empty the trashcan whenever needed? Or did I miss something? Also, can you convince me that this is actually the way it should be — that users shouldn't be able to fiddle with the filesystem easily? :)

    Read the article

  • Hardware freeze during disk activity

    - by Thomi
    I built myself a linux-based NAS. It has several drives of various sizes and ages in an LVM configuration, with 800GB or so of data. The data is served using a simple samba server. This was working flawlessly, but after physically moving it, it has developed a strange fault: Whenever I do something on the server to cause disk activity, the entire machine freezes hard. This has the effect of killing any open network connections to the box, and generally making it useless. If I leave the machine for a few minutes it seems to come right again, but obviously this isn't really a solution. There are no error or warning messages in syslog, or the kernel logs. If I power the machine on, and leave it, it runs for several days without locking up. After that time I stopped testing. It doesn't freeze instantly - obviously it doesn't freeze while booting, and I can normally log in via SSH and start poking around in a few log files for a couple of minutes before it dies. My question is: What diagnostic tests can I run to determine the casuse?

    Read the article

  • Move the uploads folder in Wordpress

    - by Victor Hurdugaci
    Currently, my Wordpress' upload folder is located in \wp-content\uploads. Initially there was no structure so all files were put there. After a while it was changed to upload the files in \wp-content\uploads\YEAR\MONTH. Now that folder contains a mix of files (those starting with + are folders) like: +wp-content | +2010 | | +02 | | | File-1 | | | File-2 | | | .. | | | File-n | | +01 | | | File-1 | | | File-2 | | | .. | | | File-n | +2009 | | +12 | | | File-1 | | | File-2 | | | .. | | | File-n | | +11 | | | File-1 | | | File-2 | | | .. | | | File-n | +.. | | | .. | Unstructured-file-1 | Unstructured-file-2 | ... | Unstructured-file-n Based on the dates of the unstructured files, I would like to move them in a structured hierarchy (based on date, move it to a folder \wp-content\uploads\YEAR\MONTH). Now, my questions are: Where do I write and execute a script to the movement (I don't have full access to the server, just to a cPanel and to the Wordpress Admin page)? What must be updated so that the links in posts, that reference the unstructured files, point to the new location of those files? Not fully related to the previous description: is it alright to move the whole uploads folder to another location, like \uploads? PS: Moving the files/updating the database manually is not an option :)

    Read the article

  • How to move or delete files from a folder containing 2 million files on an NTFS drive?

    - by Beau
    The issue is that any modification to the directory locks up Explorer indefinitely, though Samba access to other directories still works. I've tried moving files locally and over Samba. Even enumerating the directory to get the list of files locks up the computer indefinitely. I tried using Python's win32file.FindFilesIterator to iterate the files but that also hangs. My idea was to move each file to a different directory (in a directory above the directory we're dealing with) based on its timestamp, so that we'd have at most a thousand or so files in each directory... But since I can't even enumerate the files, that's been a non-starter. If I have to give up and just nuke the directory I'm willing to do that, but a standard delete also hangs indefinitely. I have set these two parameters to increase speed and they also did not help the issue: R:\>fsutil behavior query disablelastaccess disablelastaccess = 1 R:\>fsutil behavior query disable8dot3 disable8dot3 = 1 These are all sequential images that would have run into the 'bug' with 8.3 filenames whereby many similarly named files in one directory can take a long time to compute 8.3 filenames. From what I understand this data is stored in the file system even after disable8dot3 is enabled, so it may still be contributing to the problem. Any ideas?

    Read the article

  • Tools to manage sql 2008 database mirroring?

    - by lemkepf
    We are going to be moving about 20 databases that live on a single instance of sql 2000 to a sql 2008 r2 environment with database mirroring. What I'm looking for is a tool or scripts that will help me manage the conversion and management of those 20db's onto this new mirrored environment easily. There are many steps in setting each DB up and I want to automate as much as possible. Edit: Here are the steps I've been doing manually: Create the same username/passwords from the old sql 2000 server onto new sql 2008 server. Then sync those users/passwords onto the other sql 2008 server with the same SSID's so when we do the db backup and restore they match up. Take a backup of each sql 2000 db's. Copy them to server A. Restore the backup to server A. Backup from server a, copy to server b, restore there. Run the mirror "configure security" wizard. Start mirroring. I've love to be able to script this out or have a tool that does it for me. Thanks! Paul

    Read the article

  • Self-connecting printers

    - by Martin Cerny
    Hello, I work as an administrator in a small company using XP Professional on all computers and two servers with Win 2003 Server. Recently a very unusual problam occured one of the computers keeps connecting to all the printers on the network it doesn't matter if it's an administrator or Domain User as soon as somebody logs in the commputer connects all the printers. The printers are either installed on local computers or on the server and shared. There is no log-on script connecting the printers, I install them manualy and none of the other computers shows such behaviour. We have a printer which is installed on two computers and both of them share it (I'm moving it to Server from a small PC which shared it up to now, but some computers still use the old connection), meaning this specific computer connects to one of the printer two times and it can't use either of the connections. How to prevent this self-connecting to all printers (none of the other computers has this problem). If I delte them from the "Printers" folder everything works fine untill I reconnect and the Folder is once again full of all the printers we have. I solved the smaller problem, computer is now capable of printing on all of the printers (it seems there have been some registry issues), after cleaning the registry and reinstalling the printer it seems to work just fine. But the second thing prevails, the computer connects to all the printers in the network (when I remove one/multiple it is reconnected right after the next log-in by any user).

    Read the article

  • Configuring three monitors with two Radeon X1600/X1650 graphics cards under Ubuntu

    - by cpm
    I have three SyncMaster 932a monitors I want to use with two Radeon X1600/X1650 cards under Linux. I am running X.org X Server 1.6.0, as provided by Ubuntu's Wubi installer. After turning off mirroring, I ended up with this xorg.conf: Section "Monitor" Identifier "Configured Monitor" EndSection Section "Screen" Identifier "Default Screen" Monitor "Configured Monitor" Device "Configured Video Device" SubSection "Display" Virtual 2560 1024 EndSubSection EndSection Section "Device" Identifier "Configured Video Device" EndSection The left monitor had a menu bar and a task bar, the center monitor was just desktop, and windows would maximize to the current monitor. The third monitor and second graphics card weren't being used at all. Then I changed my configuration to manually specify each card with their PCI bus: Section "ServerLayout" Identifier "TheLayout" Screen 0 "Radeon Screen 1" Screen 1 "Radeon Screen 2" RightOf "Radeon Screen 1" EndSection Section "Screen" Identifier "Radeon Screen 1" Monitor "Configured Monitor" Device "Radeon the First" SubSection "Display" Virtual 2560 1024 EndSubSection EndSection Section "Screen" Identifier "Radeon Screen 2" Monitor "Configured Monitor" Device "Radeon the Second" EndSection Section "Device" Identifier "Radeon the First" Driver "radeon" BusID "PCI:1:0:0" EndSection Section "Device" Identifier "Radeon the Second" Driver "radeon" BusID "PCI:2:0:0" EndSection Section "Monitor" Identifier "Configured Monitor" EndSection Now both the left and right monitors have task bars and menu bars. Windows cannot be dragged from the first two monitors to the third monitor. Also, maximizing in the left or center window fills both monitors. I also tried adding Option "Xinerama" "true" to the ServerLayout section. X11 wasn't able to start up. I want to: Allow moving windows along all three monitors. Maximizing only fills the current monitor. Either have menu/task bars on only the left monitor or all three monitors How can I make this possible?

    Read the article

  • How can I pause console output in rxvt?

    - by Javid Jamae
    I'm running rxvt in Cygwin on a Windows box. This is how I invoke it: rxvt -sr -sl 2500 -sb -geometry 90x30 -tn rxvt -fn "Lucida Console-14" -e /usr/bin/bash --login -i Anyone know how to pause the console output in rxvt? I can use Ctrl-S / Ctrl-Q to pause / un-pause, but this won't work if a script is already running and spewing output to stdout. Highlighting the terminal window with the mouse doesn't seem to work like with other consoles such as the standard Cygwin console, or the Windows command prompt console. Some sort of scroll lock would be nice, but I can't seem to find any way to do this. I know I could just pipe my output to a file, but I want a way to pause the output for something that I didn't expect to explode with console output. Basically I want to scroll back while its running without it constantly moving me to the bottom of the output buffer as it updates more data to stdout. I don't particularly care if the solution given actually pauses the script (like when you highlight the mouse in the Windows Command window), or just scroll locks and let's me scroll while its still running the underlying script, though I'd like to know how to do both if its possible.

    Read the article

< Previous Page | 205 206 207 208 209 210 211 212 213 214 215 216  | Next Page >