Search Results

Search found 586 results on 24 pages for '802 11n'.

Page 21/24 | < Previous Page | 17 18 19 20 21 22 23 24  | Next Page >

• Atheros AR9485 wireless card doesn't work in an ASUS K53E

  - by John

  I just installed Ubuntu 11.10 32-bit version in dual boot mode on an ASUS K53. Every thing seems to work fine except for the wireless. The wireless works on Windows 7. Ubuntu finds the wireless card, but it does not appear to be turned on. The only physical means of turning on the card is the FN-F2 key combo. That works on Windows, but not in Ubuntu. I've looked in the forums for a solution and I'm not quite sure what to do. I've gathered the following information: jdwbmc@Spatha:~$ cat /etc/lsb-release; uname -a DISTRIB_ID=Ubuntu DISTRIB_RELEASE=11.10 DISTRIB_CODENAME=oneiric DISTRIB_DESCRIPTION="Ubuntu 11.10" Linux Spatha 3.0.0-12-generic #20-Ubuntu SMP Fri Oct 7 14:50:42 UTC 2011 i686 i686 i386 GNU/Linux jdwbmc@Spatha:~$ lspci -nnk | grep -iA2 net 02:00.0 Network controller [0280]: Atheros Communications Inc. AR9485 Wireless Network Adapter [168c:0032] (rev 01) Subsystem: AzureWave Device [1a3b:1186] Kernel driver in use: ath9k -- 04:00.0 Ethernet controller [0200]: Atheros Communications AR8151 v2.0 Gigabit Ethernet [1969:1083] (rev c0) Subsystem: ASUSTeK Computer Inc. Device [1043:1851] Kernel driver in use: atl1c jdwbmc@Spatha:~$ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 003: ID 058f:a014 Alcor Micro Corp. jdwbmc@Spatha:~$ iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thrff Fragment thrff Power Managementff jdwbmc@Spatha:~$ rfkill list all 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no 1: asus-wlan: Wireless LAN Soft blocked: no Hard blocked: no jdwbmc@Spatha:~$ lsmod Module Size Used by parport_pc 32114 0 ppdev 12849 0 snd_hda_codec_hdmi 31426 1 bnep 17923 2 rfcomm 38408 0 bluetooth 148839 10 bnep,rfcomm snd_hda_codec_realtek 254125 1 binfmt_misc 17292 1 joydev 17393 0 asus_nb_wmi 12469 0 asus_wmi 19333 1 asus_nb_wmi sparse_keymap 13658 1 asus_wmi uvcvideo 67271 0 videodev 85626 1 uvcvideo snd_hda_intel 24262 2 snd_hda_codec 91754 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_i ntel snd_hwdep 13276 1 snd_hda_codec snd_pcm 80468 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13132 0 wmi 18744 1 asus_wmi snd_rawmidi 25241 1 snd_seq_midi snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event arc4 12473 2 i915 505108 3 snd_timer 28932 2 snd_pcm,snd_seq snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq ath9k 112711 0 psmouse 73673 0 serio_raw 12990 0 mac80211 272785 1 ath9k drm_kms_helper 32889 1 i915 ath9k_common 13599 1 ath9k drm 192226 4 i915,drm_kms_helper ath9k_hw 293893 2 ath9k,ath9k_common ath 19387 2 ath9k,ath9k_hw cfg80211 172392 3 ath9k,mac80211,ath snd 55902 14 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_i ntel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,s nd_seq,snd_timer,snd_seq_device soundcore 12600 1 snd snd_page_alloc 14115 2 snd_hda_intel,snd_pcm mei 36466 0 i2c_algo_bit 13199 1 i915 video 18908 1 i915 lp 17455 0 parport 40930 3 parport_pc,ppdev,lp ahci 21634 3 libahci 25727 1 ahci atl1c 36638 0 xhci_hcd 72915 0 jdwbmc@Spatha:/var/lib/NetworkManager$ cat NetworkManager.state [main] NetworkingEnabled=true WirelessEnabled=true WWANEnabled=true WimaxEnabled=true jdwbmc@Spatha:~$ lspci -nn | grep 0280 02:00.0 Network controller [0280]: Atheros Communications Inc. AR9485 Wireless Network Adapter [168c:0032] (rev 01) Any help would be appreciated. Thanks.

  Read the article

• Radeon Mobility HD 5470 Not Working on Ubuntu 10.10

  - by Promather

  I recently bought a new HP DV6-3118SA laptop, but I am having a very discouraging problem with the graphics card. The graphics card is Radeon Mobility HD 5470. It doesn't install by default, but I do get some message suggesting to install the driver. If I install that driver, the next time I reboot, the screen goes blank and that's it! The same happens if I install the proprietary driver (fglrx) from ATI website. Could you please help me with this? EDIT: Following @Ronald and @Oli advice, I am dumping the output of lspci -k: 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 02) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: agpgart-intel Kernel modules: intel-agp 00:01.0 PCI bridge: Intel Corporation Core Processor PCI Express x16 Root Port (rev 02) Kernel driver in use: pcieport Kernel modules: shpchp 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 02) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: i915 Kernel modules: i915 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) Subsystem: Hewlett-Packard Company Device 144a 00:1a.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: ehci_hcd 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 05) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 05) Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: ehci_hcd 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a5) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel modules: iTCO_wdt 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA AHCI Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: ahci Kernel modules: ahci 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel modules: i2c-i801 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: intel ips Kernel modules: intel_ips 01:00.0 VGA compatible controller: ATI Technologies Inc Manhattan [Mobility Radeon HD 5000 Series] Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: radeon Kernel modules: radeon 01:00.1 Audio device: ATI Technologies Inc Manhattan HDMI Audio [Mobility Radeon HD 5000 Series] Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 02:00.0 Network controller: RaLink RT3090 Wireless 802.11n 1T/1R PCIe Subsystem: Hewlett-Packard Company Device 1453 Kernel driver in use: rt2800pci Kernel modules: rt2860sta, rt2800pci 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: r8169 Kernel modules: r8169 7f:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 02) Subsystem: Hewlett-Packard Company Device 144a

  Read the article

• Radeon Mobility HD 5470 Not Working

  - by Promather

  I recently bought a new HP DV6-3118SA laptop, but I am having a very discouraging problem with the graphics card. The graphics card is Radeon Mobility HD 5470. It doesn't install by default, but I do get some message suggesting to install the driver. If I install that driver, the next time I reboot, the screen goes blank and that's it! The same happens if I install the proprietary driver (fglrx) from ATI website. Could you please help me with this? EDIT: Following @Ronald and @Oli advice, I am dumping the output of lspci -k: 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 02) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: agpgart-intel Kernel modules: intel-agp 00:01.0 PCI bridge: Intel Corporation Core Processor PCI Express x16 Root Port (rev 02) Kernel driver in use: pcieport Kernel modules: shpchp 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 02) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: i915 Kernel modules: i915 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) Subsystem: Hewlett-Packard Company Device 144a 00:1a.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: ehci_hcd 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 05) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 05) Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: ehci_hcd 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a5) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel modules: iTCO_wdt 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA AHCI Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: ahci Kernel modules: ahci 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel modules: i2c-i801 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 05) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: intel ips Kernel modules: intel_ips 01:00.0 VGA compatible controller: ATI Technologies Inc Manhattan [Mobility Radeon HD 5000 Series] Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: radeon Kernel modules: radeon 01:00.1 Audio device: ATI Technologies Inc Manhattan HDMI Audio [Mobility Radeon HD 5000 Series] Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 02:00.0 Network controller: RaLink RT3090 Wireless 802.11n 1T/1R PCIe Subsystem: Hewlett-Packard Company Device 1453 Kernel driver in use: rt2800pci Kernel modules: rt2860sta, rt2800pci 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) Subsystem: Hewlett-Packard Company Device 144a Kernel driver in use: r8169 Kernel modules: r8169 7f:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 02) Subsystem: Hewlett-Packard Company Device 144a 7f:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 02) Subsystem: Hewlett-Packard Company Device 144a

  Read the article

• Errors when trying to compile the driver for the rtl8192su wireless adapter

  - by Tom Brito

  I have a wireless to usb adapter, and I'm having some trouble to install the drivers on Ubuntu. First of all, the readme says to use the make command, and I already got errors: $ make make[1]: Entering directory `/usr/src/linux-headers-2.6.35-22-generic' CC [M] /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.o /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c: In function ‘rtl8192_usb_probe’: /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12325: error: ‘struct net_device’ has no member named ‘open’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12326: error: ‘struct net_device’ has no member named ‘stop’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12327: error: ‘struct net_device’ has no member named ‘tx_timeout’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12328: error: ‘struct net_device’ has no member named ‘do_ioctl’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12329: error: ‘struct net_device’ has no member named ‘set_multicast_list’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12330: error: ‘struct net_device’ has no member named ‘set_mac_address’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12331: error: ‘struct net_device’ has no member named ‘get_stats’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12332: error: ‘struct net_device’ has no member named ‘hard_start_xmit’ make[2]: *** [/home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.o] Error 1 make[1]: *** [_module_/home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-2.6.35-22-generic' make: *** [all] Error 2 /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/ is the path where I copied the drivers on my computer. Any idea how to solve this? (I don't even know what the error is...) update: sudo lshw -class network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 03 serial: 78:e3:b5:e7:5f:6e size: 10MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10MB/s resources: irq:42 ioport:d800(size=256) memory:fbeff000-fbefffff memory:faffc000-faffffff memory:fbec0000-fbedffff *-network DISABLED description: Wireless interface physical id: 2 logical name: wlan0 serial: 00:26:18:a1:ae:64 capabilities: ethernet physical wireless configuration: broadcast=yes multicast=yes wireless=802.11b/g sudo lspci 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 18) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 18) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06) 00:1c.2 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 3 (rev 06) 00:1d.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev a6) 00:1f.0 ISA bridge: Intel Corporation 5 Series Chipset LPC Interface Controller (rev 06) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 6 port SATA AHCI Controller (rev 06) 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 06) 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) 02:00.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6315 Series Firewire Controller (rev 01) sudo lsusb Bus 002 Device 003: ID 0bda:0158 Realtek Semiconductor Corp. USB 2.0 multicard reader Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 004: ID 045e:00f9 Microsoft Corp. Wireless Desktop Receiver 3.1 Bus 001 Device 003: ID 0b05:1786 ASUSTek Computer, Inc. Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

  Read the article

• Hardware wireless switch has no effect after suspend and 13.10 upgrade

  - by blaineh

  This seems to be a fairly chronic problem, as shown by the following questions: How do I fix a "Wireless is disabled by hardware switch" error? Wireless disabled by hardware switch "Wireless disabled by hardware switch" after suspend and other hardware buttons ineffective - how can I solve this? but no good solutions have been found! Wireless works fine after a reboot, but after a suspend the hardware switch (for my laptop this is f12) has no effect on the wireless, it is just permanently off, and shows that it is with a red LED. All My rfkill list all reads: 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: yes Any combination with rfkill <un>block wifi doesn't work, although one time first blocking then unblocking actually turned it on again. sudo lshw -C network reads: *-network DISABLED description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 01 serial: 78:e4:00:65:2e:3f width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.11.0-12-generic firmware=N/A ip=155.99.215.79 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:90100000-9010ffff *-network DISABLED description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 02 serial: c8:0a:a9:89:b4:30 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:2000(size=256) memory:90010000-90010fff memory:90000000-9000ffff memory:90020000-9002ffff Also, adding a /etc/pm/sleep.d/brcm.sh file as recommended here simply prevents the laptop from suspending at all, which of course is no good. This question has an answer urging to install the original driver, but it wasn't an "accepted answer" so I'd rather not take a chance on it. Also I'll admit I'm a bit lost on that and would like help doing so with the specific information I've given. xev shows that no internal event is triggered for my wireless switch (f12), but other function keys also acting as hardware switches work fine. I would be happy to provide more information, so long as you're willing to help me find it for you! This is a very annoying bug. I have a Compaq Presario CQ62. Edit. I just tried to reload bios defaults (or something) as shown by this video. Didn't work. Edit. I tried the contents of this answer, and it didn't work. Edit. I made a pastebin of dmesg. I couldn't even begin to understand the contents. Edit. Output of lspci | grep Network: 02:00.0 Network controller: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) (rev 01)

  Read the article

• Wireless cycling between connected and disconnected

  - by Tony Kilgore

  My friend has a Acer Aspire 5733Z-4851 it keeps disconnecting and connecting to his wifi but his hard wire will run just fine. Any suggestions? All the codes: lspci: 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 02) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 02) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 05) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 05) 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 05) 00:1d.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a5) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 05) 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 05) 01:00.0 Ethernet controller: Broadcom Corporation NetLink BCM57780 Gigabit Ethernet PCIe (rev 01) 02:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 02) ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 02) ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 02) ff:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 02) ff:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 02) ff:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 02) lsmod: Module Size Used by snd_seq_dummy 12798 0 rfcomm 46619 0 bnep 18140 2 bluetooth 209199 10 rfcomm,bnep parport_pc 32688 0 ppdev 17073 0 lp 17759 0 parport 46345 3 parport_pc,ppdev,lp binfmt_misc 17500 1 ums_realtek 17949 0 snd_hda_codec_realtek 77876 1 uas 17844 0 coretemp 13400 0 snd_hda_intel 33491 4 snd_hda_codec 134212 2 snd_hda_codec_realtek,snd_hda_intel snd_hwdep 13602 1 snd_hda_codec snd_pcm 96580 2 snd_hda_intel,snd_hda_codec snd_seq_midi 13324 0 snd_rawmidi 30512 1 snd_seq_midi uvcvideo 76749 0 videobuf2_core 32851 1 uvcvideo videodev 120309 2 uvcvideo,videobuf2_core videobuf2_vmalloc 12860 1 uvcvideo videobuf2_memops 13368 1 videobuf2_vmalloc snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61521 3 snd_seq_dummy,snd_seq_midi,snd_seq_midi_event snd_timer 29425 2 snd_pcm,snd_seq arc4 12529 2 snd_seq_device 14497 4 snd_seq_dummy,snd_seq_midi,snd_rawmidi,snd_seq psmouse 95552 0 ath9k 131308 0 tg3 148780 0 snd 78734 17 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device microcode 22803 0 mac80211 539908 1 ath9k ath9k_common 14055 1 ath9k ath9k_hw 395218 2 ath9k,ath9k_common ath 23827 3 ath9k,ath9k_common,ath9k_hw i915 520629 3 soundcore 15047 1 snd serio_raw 13215 0 cfg80211 206566 3 ath9k,mac80211,ath snd_page_alloc 18484 2 snd_hda_intel,snd_pcm intel_ips 18049 0 lpc_ich 17061 0 drm_kms_helper 46784 1 i915 drm 275528 4 i915,drm_kms_helper mei 40690 0 i2c_algo_bit 13413 1 i915 joydev 17457 0 acer_wmi 32453 0 sparse_keymap 13890 1 acer_wmi mxm_wmi 12979 0 mac_hid 13205 0 wmi 19070 2 acer_wmi,mxm_wmi video 19335 2 i915,acer_wmi usb_storage 48838 1 ums_realtek sudo lshw -C network: *-network description: Ethernet interface product: NetLink BCM57780 Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 01 serial: b8:70:f4:9a:35:b6 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.123 duplex=half firmware=sb latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:44 memory:d3400000-d340ffff[/QUOTE][QUOTE]*-network description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 01 serial: 68:a3:c4:eb:60:7d width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.5.0-19-generic firmware=N/A ip=192.168.0.168 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:d2400000-d240ffff)

  Read the article

• 12.04 making BCM4313 card work with aircrack-ng?

  - by Charles Forest

  I'm a real Linux Noob, just started using it (this month) and until now i had no issues. now i'm trying to set-up aircrack-ng on my laptop, but it seems like it's using the worst card possible (or almost) there is a TON of tutorial on this card (seems to be hell to set-up) i have tryed some, but i ended up uninstalling my drivers, messing with my desktops, and ended by having no more "X" to close my windows (i have no clue how i ended there) i just re-installed my linux (took me 2 hours to setup everything again), but now i'm a bit "Scared" to try tutorials randomly again. Right now it says the driver is wl, wich is not the one i want (AFAIK it's not supported) i'm not sure what kind of informations are needed, but here's what i think could be usefull. lspci -knn 00:00.0 Host bridge [0600]: Intel Corporation 2nd Generation Core Processor Family DRAM Controller [8086:0104] (rev 09) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel driver in use: agpgart-intel 00:01.0 PCI bridge [0604]: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port [8086:0101] (rev 09) Kernel driver in use: pcieport Kernel modules: shpchp 00:02.0 VGA compatible controller [0300]: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller [8086:0116] (rev 09) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel driver in use: i915 Kernel modules: i915 00:16.0 Communication controller [0780]: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 [8086:1c3a] (rev 04) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel driver in use: mei Kernel modules: mei 00:1a.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 [8086:1c2d] (rev 04) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel driver in use: ehci_hcd 00:1b.0 Audio device [0403]: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller [8086:1c20] (rev 04) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 [8086:1c10] (rev b4) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.3 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 [8086:1c16] (rev b4) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.4 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 5 [8086:1c18] (rev b4) Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 [8086:1c26] (rev 04) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel driver in use: ehci_hcd 00:1f.0 ISA bridge [0601]: Intel Corporation HM65 Express Chipset Family LPC Controller [8086:1c49] (rev 04) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel modules: iTCO_wdt 00:1f.2 SATA controller [0106]: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller [8086:1c03] (rev 04) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel driver in use: ahci 00:1f.3 SMBus [0c05]: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller [8086:1c22] (rev 04) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel modules: i2c-i801 01:00.0 3D controller [0302]: NVIDIA Corporation GF108 [GeForce GT 540M] [10de:0df4] (rev a1) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel driver in use: nouveau Kernel modules: nouveau, nvidiafb WIRELESS CARD 02:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller [14e4:4727] (rev 01) Subsystem: Wistron NeWeb Corp. Device [185f:051a] Kernel driver in use: wl Kernel modules: wl, bcma, brcmsmac REST... 03:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 06) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel driver in use: r8169 Kernel modules: r8169 04:00.0 USB controller [0c03]: NEC Corporation uPD720200 USB 3.0 Host Controller [1033:0194] (rev 04) Subsystem: Samsung Electronics Co Ltd Device [144d:c0a5] Kernel driver in use: xhci_hcd Also, if i'm "screwed" with my hardware, just tell me.

  Read the article

• WiFi stops working after a while in Lenovo ThinkPad W520 (Ubuntu 12.04)

  - by el10780

  After several minutes(I do not know how many) there is no internet connection on my laptop via Wi-Fi.Ubuntu doesn't show any kind of message that my WiFi was disconnected neither there is a signal drop,but suddenly Firefox stops connecting to web pages.I checked my modem/router and it seems that it is working fine.I tried also to reboot the WiFi device and nothing happens.The only thing that it makes it work again is a reboot of the system and if I do not want to do a reboot then I am enforced to connect to the Internet using Ethernet cable.Does anybody know what is happening? ## Some Hardware info that might be helpful ## el10780@ThinkPad-W520:~$ sudo lshw -class network *-network description: Ethernet interface product: 82579LM Gigabit Network Connection vendor: Intel Corporation physical id: 19 bus info: pci@0000:00:19.0 logical name: eth0 version: 04 serial: f0:de:f1:f1:be:10 size: 100Mbit/s capacity: 1Gbit/s width: 32 bits clock: 33MHz capabilities: pm msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e1000e driverversion=1.5.1-k duplex=full firmware=0.13-3 ip=192.168.0.10 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:50 memory:f3a00000-f3a1ffff memory:f3a2b000-f3a2bfff ioport:6080(size=32) *-network description: Wireless interface product: Centrino Advanced-N + WiMAX 6250 vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 5e serial: 64:80:99:63:14:74 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-26-generic firmware=41.28.5.1 build 33926 ip=192.168.0.6 latency=0 link=yes multicast=yes wireless=IEEE 802.11abgn resources: irq:52 memory:f3900000-f3901fff *-network description: Ethernet interface physical id: 1 bus info: usb@2:1.3 logical name: wmx0 serial: 00:1d:e1:53:b2:e8 capabilities: ethernet physical configuration: driver=i2400m firmware=i6050-fw-usb-1.5.sbcf link=no el10780@ThinkPad-W520:~$ lspci 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:16.3 Serial controller: Intel Corporation 6 Series/C200 Series Chipset Family KT Controller (rev 04) 00:19.0 Ethernet controller: Intel Corporation 82579LM Gigabit Network Connection (rev 04) 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b4) 00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b4) 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b4) 00:1c.4 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 5 (rev b4) 00:1c.6 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 7 (rev b4) 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation QM67 Express Chipset Family LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 04) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 04) 01:00.0 VGA compatible controller: NVIDIA Corporation GF108 [Quadro 1000M] (rev a1) 03:00.0 Network controller: Intel Corporation Centrino Advanced-N + WiMAX 6250 (rev 5e) 0d:00.0 System peripheral: Ricoh Co Ltd Device e823 (rev 08) 0d:00.3 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 PCIe IEEE 1394 Controller (rev 04) 0e:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04) el10780@ThinkPad-W520:~$ rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: tpacpi_bluetooth_sw: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no 3: i2400m-usb:2-1.3:1.0: WiMAX Soft blocked: yes Hard blocked: no The weirdest thing is this screenshot which I took after running the **Additional Drivers** program.I mean I have a NVidia Quadro 1000M and my Intel Centrino WiFi Card and this shows that there are not proprietay drivers for my system. http://imageshack.us/photo/my-images/268/screenshotfrom201207062.png/

  Read the article

• Need help partitioning when reinstalling Ubuntu 14.04

  - by Chris M.

  I upgraded to 14.04 about a month ago on my HP Mini netbook (about 16 GB hard disk). A few days ago the system crashed (I don't know why but I was using internet at the time). When I restarted the computer, Ubuntu would not load. Instead, I got a message from the BIOS saying Reboot and Select proper Boot device or Insert Boot Media in selected Boot device and press a key I took this to mean that I needed to reinstall 14.04. When I try to reinstall Ubuntu from the USB stick, I choose "Erase disk and install Ubuntu" but then I get a message: Some of the partitions you created are too small. Please make the following partitions at least this large: / 3.3 GB If you do not go back to the partitioner and increase the size of these partitions, the installation may fail. At first I hit Continue to see if it would install anyway, and it gave the message: The attempt to mount a file system with type ext4 in SCSI1 (0,0,0), partition # 1 (sda) at / failed. You may resume partitioning from the partitioning menu. The second time I hit Go Back, and it took me to the following partitioning table: Device Type Mount Point Format Size Used System /dev/sda /dev/sda1 ext4 (checked) 3228 MB Unknown /dev/sda5 swap (not checked) 1063 MB Unknown + - Change New Partition Table... Revert Device for boot loader installation: /dev/sda ATA JM Loader 001 (4.3 GB) At this point I'm not sure what to do. I've never partitioned my hard drive before and I don't want to screw things up. (I'm not particularly tech savvy.) Can you instruct me what I should do. (P.S. I'm afraid the table might not appear as I typed it in.) Results from fdisk: ubuntu@ubuntu:~$ sudo fdisk -l Disk /dev/sda: 4294 MB, 4294967296 bytes 255 heads, 63 sectors/track, 522 cylinders, total 8388608 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/sda doesn't contain a valid partition table Disk /dev/sdb: 7860 MB, 7860125696 bytes 155 heads, 31 sectors/track, 3194 cylinders, total 15351808 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0009a565 Device Boot Start End Blocks Id System /dev/sdb1 * 2768 15351807 7674520 b W95 FAT32 ubuntu@ubuntu:~$ Here is what it displays when I open the Disks utility (I tried the screenshot terminal command you suggested but it didn't seem to do anything): 4.3 GB Hard Disk /dev/sda Model: JM Loader 001 (01000001) Size: 4.3 GB (4,294,967,296 bytes) Serial Number: 01234123412341234 Assessment: SMART is not supported Volumes Size: 4.3 GB (4,294,967,296 bytes) Device: /dev/sda Contents: Unknown (There is a button in the utility that when you click it gives the following options: Format... Create Disk Image... Restore Disk Image... Benchmark but SMART Data & Self-Tests... is dimmed out) When I hit F9 Change Boot Device Order, it shows the hard drive as: SATA:PM-JM Loader 001 When I hit F10 to get me into the BIOS Setup Utility, under Diagnostic it shows: Primary Hard Disk Self Test Not Support NetworkManager Tool State: disconnected Device: eth0 Type: Wired Driver: atl1c State: unavailable Default: no HW Address: 00:26:55:B0:7F:0C Capabilities: Carrier Detect: yes Wired Properties Carrier: off When I run command lshw -C network, I get: WARNING: you should run this program as super-user. *-network description: Network controller product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:01:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: bus_master cap_list configuration: driver=b43-pci-bridge latency=0 resources: irq:16 memory:feafc000-feafffff *-network description: Ethernet interface product: AR8132 Fast Ethernet vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: c0 serial: 00:26:55:b0:7f:0c capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.1-NAPI latency=0 link=no multicast=yes port=twisted pair resources: irq:43 memory:febc0000-febfffff ioport:ec80(size=128) WARNING: output may be incomplete or inaccurate, you should run this program as super-user.

  Read the article

• What's wrong with my wireless?

  - by dazzle

  I am having issues with my wireless connection. My connection is constantly disconnecting, then attempting to reconnect, reconnecting momentarily, then disconnecting etc. on times scales that range from seconds to minutes. In the meantime, needless to say I'm having significant packet loss. I'm running Ubuntu 14.04 64bit, updated and upgraded to today. Here is my card and driver: delta@sager:~$ lspci -vq | grep -i wireless -B 1 -A 5 04:00.0 Network controller: Intel Corporation Wireless 7260 (rev 73) Subsystem: Intel Corporation Dual Band Wireless-AC 7260 Flags: bus master, fast devsel, latency 0, IRQ 47 Memory at f7d00000 (64-bit, non-prefetchable) [size=8K] Capabilities: Kernel driver in use: iwlwifi Here is my kernel: delta@sager:~$ uname -r 3.13.0-34-generic None of the other machines on my home network are having these issues. Windows Vista is networking without issue for goodness sake ;-) Here is a small clipping from the output of dmesg. As you can see, I am getting a cfg80211 message of some sort over and over again (FYI, I've replaced my MAC address with a series of dashes, so anytime there is a ---------------, that was where the MAC address was: [ 1881.739161] wlan1: authenticate with --------------- [ 1881.741561] wlan1: send auth to --------------- (try 1/3) [ 1881.743440] wlan1: authenticated [ 1881.746027] wlan1: associate with --------------- (try 1/3) [ 1881.749244] wlan1: RX AssocResp from --------------- (capab=0x411 status=0 aid=4) [ 1881.754727] wlan1: associated [ 1881.754827] cfg80211: Calling CRDA for country: US [ 1881.761552] cfg80211: Regulatory domain changed to country: US [ 1881.761559] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 1881.761564] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 1881.761568] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 1881.761571] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1881.761574] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1881.761577] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1881.761580] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 1881.761584] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm) [ 1882.391038] cfg80211: Calling CRDA to update world regulatory domain [ 1882.396254] cfg80211: World regulatory domain updated: [ 1882.396260] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 1882.396265] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1882.396268] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1882.396271] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 1882.396274] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1882.396277] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1886.148252] wlan1: authenticate with --------------- [ 1886.150005] wlan1: send auth to --------------- (try 1/3) [ 1886.151807] wlan1: authenticated [ 1886.154847] wlan1: associate with --------------- (try 1/3) [ 1886.158147] wlan1: RX AssocResp from --------------- (capab=0x411 status=0 aid=4) [ 1886.163464] wlan1: associated [ 1886.163520] wlan1: Limiting TX power to 30 (30 - 0) dBm as advertised by --------------- [ 1886.163588] cfg80211: Calling CRDA for country: US [ 1886.170500] cfg80211: Regulatory domain changed to country: US [ 1886.170508] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 1886.170513] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 1886.170517] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 1886.170520] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1886.170523] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1886.170526] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1886.170529] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 1886.170533] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm) [ 1887.200197] cfg80211: Calling CRDA to update world regulatory domain [ 1887.203655] cfg80211: World regulatory domain updated: [ 1887.203659] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 1887.203662] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1887.203664] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1887.203666] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 1887.203668] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1887.203670] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) I've poked around on AskUbuntu, and have not found any adequate solutions; have also found similar threads that were left unanswered. Any advice/experience/threads I might be able to pull on would be greatly appreciated. In your opinion, is this a kernel issue, hardware issue, etc.? Thanks in advance. EDIT: chili, here's the output of iwconfig: delta@sager:~$ iwconfig wlan1 IEEE 802.11abg ESSID:"LANbeforetime" Mode:Managed Frequency:2.412 GHz Access Point: ----------- Bit Rate=48 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=44/70 Signal level=-66 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:80 Missed beacon:0 eth0 no wireless extensions. lo no wireless extensions.

  Read the article

• Need help with chronic slow wifi connections

  - by mgeorge

  I have had chronic slow wifi connections on several networks for a while now, I think since my update to 12.04 when it came out. I have tried many of the tips and tricks already available out there in the forums with no luck (wicd, etc..). I want to see if any of you experts out there might be able to help me, and thanks in advance!! I use ubuntu 12.04 on a lenovo ideapad y650, and most networks I connect to lose the connection frequently or do not give appropriate bandwidth when I am connected. Here are some results of the usual go-to system checks: cat /etc/lsb-release; uname -a: DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION="Ubuntu 12.04.2 LTS" Linux mgeorge-lenovo 3.2.0-48-generic-pae #74-Ubuntu SMP Thu Jun 6 20:05:01 UTC 2013 i686 i686 i386 GNU/Linux lspci -nnk | grep -iA2 net: 04:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 5100 AGN [Shiloh] Network Connection [8086:4237] Subsystem: Intel Corporation WiFi Link 5100 AGN [8086:1211] Kernel driver in use: iwlwifi -- 08:00.0 Ethernet controller [0200]: Broadcom Corporation NetLink BCM5784M Gigabit Ethernet PCIe [14e4:1698] (rev 10) Subsystem: Lenovo Device [17aa:3878] Kernel driver in use: tg3 lsusb: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 002: ID 090c:7371 Silicon Motion, Inc. - Taiwan (formerly Feiya Technology Corp.) iwconfig: lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"Dyno" Mode:Managed Frequency:2.412 GHz Access Point: CC:5D:4E:46:0A:93 Bit Rate=150 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=70/70 Signal level=-40 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:948 Invalid misc:728 Missed beacon:0 eth0 no wireless extensions. rfkill list all: 0: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: ideapad_bluetooth: Bluetooth Soft blocked: yes Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no lsmod: Module Size Used by uvcvideo 67203 0 videodev 86588 1 uvcvideo nouveau 712674 3 ttm 65344 1 nouveau drm_kms_helper 45466 1 nouveau drm 197641 5 nouveau,ttm,drm_kms_helper i2c_algo_bit 13199 1 nouveau mxm_wmi 12893 1 nouveau wmi 18744 1 mxm_wmi joydev 17393 0 arc4 12473 2 snd_hda_codec_realtek 174313 1 snd_hda_codec_hdmi 31775 1 snd_hda_intel 32719 3 snd_hda_codec 109562 3 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec snd_pcm 80916 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13132 0 snd_rawmidi 25424 1 snd_seq_midi snd_seq_midi_event 14475 1 snd_seq_midi psmouse 86520 0 snd_seq 51592 2 snd_seq_midi,snd_seq_midi_event serio_raw 13027 0 snd_timer 28931 2 snd_pcm,snd_seq snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq iwlwifi 366509 0 mac80211 436493 1 iwlwifi snd 62218 16 snd_hda_codec_realtek,snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,sn d_rawmidi,snd_seq,snd_timer,snd_seq_device ideapad_laptop 17890 0 sparse_keymap 13658 1 ideapad_laptop cfg80211 178877 2 iwlwifi,mac80211 ir_lirc_codec 12739 0 lirc_dev 18700 1 ir_lirc_codec soundcore 14635 1 snd snd_page_alloc 14108 2 snd_hda_intel,snd_pcm ir_mce_kbd_decoder 12681 0 ir_sony_decoder 12462 0 ir_jvc_decoder 12459 0 ir_rc6_decoder 12459 0 ir_rc5_decoder 12459 0 rc_rc6_mce 12454 0 ir_nec_decoder 12459 0 video 19115 1 nouveau ene_ir 18019 0 rc_core 21263 10 ir_lirc_codec,ir_mce_kbd_decoder,ir_sony_decoder,ir_jvc_decoder,ir_rc6_decoder,ir_rc5_decoder,rc_rc6_mce,ir_nec_decoder,ene_ir bnep 17830 2 rfcomm 38139 0 parport_pc 32114 0 bluetooth 158479 10 bnep,rfcomm ppdev 12849 0 binfmt_misc 17292 1 mac_hid 13077 0 lp 17455 0 parport 40930 3 parport_pc,ppdev,lp tg3 141414 0 nm-tool: NetworkManager Tool State: connected (global) - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: tg3 State: unavailable Default: no HW Address: 00:23:5A:CC:85:BD Capabilities: Carrier Detect: yes Wired Properties Carrier: off - Device: wlan0 [Dyno] -------------------------------------------------------- Type: 802.11 WiFi Driver: iwlwifi State: connected Default: yes HW Address: 00:22:FA:D0:94:CA Capabilities: Speed: 150 Mb/s Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points (* = current AP) *Dyno: Infra, CC:5D:4E:46:0A:93, Freq 2412 MHz, Rate 54 Mb/s, Strength 81 WPA2 IPv4 Settings: Address: 10.0.0.43 Prefix: 24 (255.255.255.0) Gateway: 10.0.0.1 DNS: 10.0.0.1

  Read the article

• My LAN USB NIC is not working in ubuntu 11.10?

  - by Gaurav_Java

  Today i start my system its seems that my LAN port is not working . so i buy one USB to LAN adapter and i plug in ubuntu system its doen't connect automatically .when i check result lsusb its shows me that there is one DM9601 Ethernet adapter is connected when i click on network information in panel its shows me that there is something " wired NEtwork (Broadcom NetLink BCM5784M gigabit Ethernet PCIe) I think want some driver for that .i don't have any idea how it can be used ? here output of sudo lspci -nn *00:00.0 Host bridge [0600]: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub [8086:2a40] (rev 07) 00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller [8086:2a42] (rev 07) 00:02.1 Display controller [0380]: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller [8086:2a43] (rev 07) 00:1a.0 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 [8086:2937] (rev 03) 00:1a.1 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 [8086:2938] (rev 03) 00:1a.7 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 [8086:293c] (rev 03) 00:1b.0 Audio device [0403]: Intel Corporation 82801I (ICH9 Family) HD Audio Controller [8086:293e] (rev 03) 00:1c.0 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 [8086:2940] (rev 03) 00:1c.1 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 [8086:2942] (rev 03) 00:1c.2 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 3 [8086:2944] (rev 03) 00:1c.4 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 [8086:2948] (rev 03) 00:1d.0 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 [8086:2934] (rev 03) 00:1d.1 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 [8086:2935] (rev 03) 00:1d.2 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 [8086:2936] (rev 03) 00:1d.3 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 [8086:2939] (rev 03) 00:1d.7 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 [8086:293a] (rev 03) 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev 93) 00:1f.0 ISA bridge [0601]: Intel Corporation ICH9M LPC Interface Controller [8086:2919] (rev 03) 00:1f.2 SATA controller [0106]: Intel Corporation ICH9M/M-E SATA AHCI Controller [8086:2929] (rev 03) 00:1f.3 SMBus [0c05]: Intel Corporation 82801I (ICH9 Family) SMBus Controller [8086:2930] (rev 03) 02:00.0 Ethernet controller [0200]: Broadcom Corporation NetLink BCM5784M Gigabit Ethernet PCIe [14e4:1698] (rev 10) 04:00.0 Network controller [0280]: Intel Corporation WiFi Link 5100 [8086:4232]* sudo lshw -class network *-network description: Ethernet interface product: NetLink BCM5784M Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 10 serial: 00:1f:16:9a:56:98 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 firmware=sb v2.19 latency=0 link=no multicast=yes port=twisted pair resources: irq:47 memory:f4500000-f450ffff *-network DISABLED description: Wireless interface product: WiFi Link 5100 vendor: Intel Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: wlan0 version: 00 serial: 00:22:fa:09:02:00 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-17-generic firmware=8.83.5.1 build 33692 latency=0 link=no multicast=yes wireless=IEEE 802.11abgn resources: irq:46 memory:f4600000-f4601fff *-network description: Ethernet interface physical id: 4 logical name: eth1 serial: 00:60:6e:00:f1:7d size: 100Mbit/s capacity: 100Mbit/s capabilities: ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=dm9601 driverversion=22-Aug-2005 duplex=full firmware=Davicom DM9601 USB Ethernet ip=192.168.1.34 link=yes multicast=yes port=MII speed=100Mbit/s I am using Wimax internet connection which i have to connect from browser . at that time my system is not showing that i am connected to any wired connection. but when i connect internet from other system after getting conneted to internet . when i plug again my USB LAN then its shows that you are conneted to wired connetion. here is screenshot for conneting wimax from browser after connecting to internet network connection shows

  Read the article

• Upgraded to 12.04 now wifi doesn't work

  - by Benito Kestelman

  My laptop's wifi stopped working when I upgraded to Ubuntu 12.04 (wired works). I just reinstalled 12.04 over my old 12.04 on which wifi didn't work either in an attempt to restore any settings I may have accidentally changed, but it still doesn't work. I also used a wired connection to install updates in case this bug has been fixed, but it has not. Here is the result of sudo lshw -class network: *-network description: Wireless interface product: Centrino Wireless-N + WiMAX 6150 vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 67 serial: 40:25:c2:5f:5b:f4 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-29-generic-pae firmware=41.28.5.1 build 33926 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:51 memory:de800000-de801fff *-network description: Ethernet interface product: AR8151 v2.0 Gigabit Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 logical name: eth0 version: c0 serial: 14:da:e9:c0:da:78 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI firmware=N/A latency=0 link=no multicast=yes port=twisted pair resources: irq:54 memory:dd400000-dd43ffff ioport:a000(size=128) Here is rfkill list all: 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no 1: asus-wlan: Wireless LAN Soft blocked: no Hard blocked: no 2: asus-wimax: WiMAX Soft blocked: no Hard blocked: no lsusb: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 003: ID 8087:07d6 Intel Corp. Bus 001 Device 004: ID 13d3:5710 IMC Networks Bus 002 Device 003: ID 045e:0745 Microsoft Corp. Nano Transceiver v1.0 for Bluetooth Bus 003 Device 003: ID 0781:5530 SanDisk Corp. Cruzer lspci: 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) 00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b5) 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) 00:1c.5 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 6 (rev b5) 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation HM65 Express Chipset Family LPC Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) 02:00.0 Network controller: Intel Corporation Centrino Wireless-N + WiMAX 6150 (rev 67) 03:00.0 USB controller: ASMedia Technology Inc. ASM1042 SuperSpeed USB Host Controller 04:00.0 Ethernet controller: Atheros Communications Inc. AR8151 v2.0 Gigabit Ethernet (rev c0)

  Read the article

• Drivers for Atheros AR928X?

  - by Pato7

  I am new in Ubuntu and I had a big trouble with wifi. My ubuntu 12.10 doesn't detect my wifi card and I can't toggle the "activate wireless" option on the tasks bar (it is grey). I searched for drivers to make it work, but nothing worked for me. Can anyone give me a hand? Many thanks in advanced! lspci output 00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07) 00:01.0 PCI bridge: Intel Corporation Mobile 4 Series Chipset PCI Express Graphics Port (rev 07) 00:1a.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) 00:1a.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) 00:1a.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) 00:1a.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03) 00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 (rev 03) 00:1c.2 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 3 (rev 03) 00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) 00:1d.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation 82801IBM/IEM (ICH9M/ICH9M-E) 4 port SATA Controller [AHCI mode] (rev 03) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03) 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI RV710 [Mobility Radeon HD 4500/5100 Series] 01:00.1 Audio device: Advanced Micro Devices [AMD] nee ATI RV710/730 HDMI Audio [Radeon HD 4000 series] 02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8057 PCI-E Gigabit Ethernet Controller (rev 10) 03:00.0 Network controller: Atheros Communications Inc. AR928X Wireless Network Adapter (PCI-Express) (rev 01) 0c:03.0 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller (rev 05) 0c:03.1 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 22) 0c:03.2 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 12) lshw -c network output *-network descripción: Ethernet interface producto: 88E8057 PCI-E Gigabit Ethernet Controller fabricante: Marvell Technology Group Ltd. id físico: 0 información del bus: pci@0000:02:00.0 nombre lógico: eth0 versión: 10 serie: 00:24:be:83:b2:4f tamaño: 100Mbit/s capacidad: 1Gbit/s anchura: 64 bits reloj: 33MHz capacidades: pm msi pciexpress bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuración: autonegotiation=on broadcast=yes driver=sky2 driverversion=1.30 duplex=full ip=192.168.1.123 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s recursos: irq:45 memoria:d3520000-d3523fff ioport:c000(size=256) memoria:d3500000-d351ffff *-network DESACTIVADO descripción: Interfaz inalámbrica producto: AR928X Wireless Network Adapter (PCI-Express) fabricante: Atheros Communications Inc. id físico: 0 información del bus: pci@0000:03:00.0 nombre lógico: wlan0 versión: 01 serie: 2c:81:58:e6:b6:03 anchura: 64 bits reloj: 33MHz capacidades: pm msi pciexpress msix bus_master cap_list ethernet physical wireless configuración: broadcast=yes driver=ath9k driverversion=3.5.0-18-generic firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn recursos: irq:17 memoria:d2100000-d210ffff rfkill list all output 0: phy0: Wireless LAN Soft blocked: yes Hard blocked: yes 1: sony-wifi: Wireless LAN Soft blocked: yes Hard blocked: no

  Read the article

• make_tuple with boost::python under Visual Studio 9

  - by celil

  Trying to build the following simple example #include <boost/python.hpp> using namespace boost::python; tuple head_and_tail(object sequence) { return make_tuple(sequence[0],sequence[-1]); } available here, I end up with this compilation error under Visual Studio 9 error C2668: 'boost::python::make_tuple' : ambiguous call to overloaded function 1> C:\Program Files\boost_1_42_0\boost/python/detail/make_tuple.hpp(22): could be 'boost::python::tuple boost::python::make_tuple<boost::python::api::object_item,boost::python::api::object_item>(const A0 &,const A1 &)' 1> with 1> [ 1> A0=boost::python::api::object_item, 1> A1=boost::python::api::object_item 1> ] 1> C:\Program Files\boost_1_42_0\boost/tuple/detail/tuple_basic.hpp(802): or 'boost::tuples::tuple<T0,T1,T2,T3,T4,T5,T6,T7,T8,T9> boost::tuples::make_tuple<boost::python::api::object_item,boost::python::api::object_item>(const T0 &,const T1 &)' [found using argument-dependent lookup] 1> with 1> [ 1> T0=boost::python::api::proxy<boost::python::api::item_policies>, 1> T1=boost::python::api::proxy<boost::python::api::item_policies>, 1> T2=boost::tuples::null_type, 1> T3=boost::tuples::null_type, 1> T4=boost::tuples::null_type, 1> T5=boost::tuples::null_type, 1> T6=boost::tuples::null_type, 1> T7=boost::tuples::null_type, 1> T8=boost::tuples::null_type, 1> T9=boost::tuples::null_type 1> ] Is this a bug in boost::python, or am I doing something wrong? How can I get the above program to compile?

  Read the article

• "Unable to associated Elastic IP with cluster" in Eclipse Plugin Tutorial

  - by Jeffrey Chee

  Hi all, I am currently trying to evaluate AWS for my company and was trying to follow the tutorials on the web. http://developer.amazonwebservices.com/connect/entry.jspa?externalID=2241 However I get the below error during startup of the server instance: Unable to associated Elastic IP with cluster: Unable to detect that the Elastic IP was orrectly associated. java.lang.Exception: Unable to detect that the Elastic IP was correctly associated at com.amazonaws.ec2.cluster.Cluster.associateElasticIp(Cluster.java:802) at com.amazonaws.ec2.cluster.Cluster.start(Cluster.java:311) at com.amazonaws.eclipse.wtp.ElasticClusterBehavior.launch(ElasticClusterBehavior.java:611) at com.amazonaws.eclipse.wtp.Ec2LaunchConfigurationDelegate.launch(Ec2LaunchConfigurationDelegate.java:47) at org.eclipse.debug.internal.core.LaunchConfiguration.launch(LaunchConfiguration.java:853) at org.eclipse.debug.internal.core.LaunchConfiguration.launch(LaunchConfiguration.java:703) at org.eclipse.debug.internal.core.LaunchConfiguration.launch(LaunchConfiguration.java:696) at org.eclipse.wst.server.core.internal.Server.startImpl2(Server.java:3051) at org.eclipse.wst.server.core.internal.Server.startImpl(Server.java:3001) at org.eclipse.wst.server.core.internal.Server$StartJob.run(Server.java:300) at org.eclipse.core.internal.jobs.Worker.run(Worker.java:55) Then after a while, another error occur: Unable to publish server configuration files: Unable to copy remote file after trying 4 timeslocal file: 'XXXXXXXX/XXX.zip' Results from first attempt: Unexpected exception: java.net.ConnectException: Connection timed out: connect root cause: java.net.ConnectException: Connection timed out: connect at com.amazonaws.eclipse.ec2.RemoteCommandUtils.copyRemoteFile(RemoteCommandUtils.java:128) at com.amazonaws.eclipse.wtp.tomcat.Ec2TomcatServer.publishServerConfiguration(Ec2TomcatServer.java:172) at com.amazonaws.ec2.cluster.Cluster.publishServerConfiguration(Cluster.java:369) at com.amazonaws.eclipse.wtp.ElasticClusterBehavior.publishServer(ElasticClusterBehavior.java:538) at org.eclipse.wst.server.core.model.ServerBehaviourDelegate.publish(ServerBehaviourDelegate.java:866) at org.eclipse.wst.server.core.model.ServerBehaviourDelegate.publish(ServerBehaviourDelegate.java:708) at org.eclipse.wst.server.core.internal.Server.publishImpl(Server.java:2731) at org.eclipse.wst.server.core.internal.Server$PublishJob.run(Server.java:278) at org.eclipse.core.internal.jobs.Worker.run(Worker.java:55) Can anyone point me to what I'm doing wrong? I followed the tutorials and the video tutorials on youtube exactly. Best Regards ~Jeffrey

  Read the article

• Compiling a program with a legacy version of gcc

  - by wyatt

  This is probably a very difficult problem to troubleshoot with the information I can practically provide, but I'm hoping someone might be able to at least point me in a possible direction. I'm trying to install HTK (http://htk.eng.cam.ac.uk/), which, according to this page needs to be installed using gcc 3.4. Their method of implementing backwards compatibility: #yum install compat-gcc-34-c++ compat-gcc-34 won't work for me as I'm running Ubuntu (On that note, I take it I can't simply install YUM and the subsequent package, since it's an entirely different distro, but if I'm wrong I'd love to hear it). I instead installed two versions of gcc 3.4 - 3.4.0 and 3.4.6 using instructions from this site. I then added the lines suggested by that page to the top of the makefile (on this note, what's the difference between makefile and makefile.in? I tried adding the lines to the top of both files regardless), both for version 3.4.0 and 3.4.6, but both failed. I also tried, on the off-chance, compiling it with my current version (4.4.1), but that also failed. I got the errors: (cd HTKLib && make HTKLib.a) \ || case "" in k) fail=yes;; ) exit 1;; esac; make1: Entering directory /home/charles/bin/htk-3.4/HTKLib' gcc -ansi -D_SVID_SOURCE -DOSS_AUDIO -D'ARCH="i686"' -Wall -Wno-switch -g -O2 -I. -c -o HGraf.o HGraf.c HGraf.c:73:77: error: X11/Xlib.h: No such file or directory HGraf.c:74:23: error: X11/Xutil.h: No such file or directory HGraf.c:75:21: error: X11/Xos.h: No such file or directory HGraf.c:77:27: error: X11/keysymdef.h: No such file or directory HGraf.c:87: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘*’ token HGraf.c:88: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘rootW’ HGraf.c:91: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘theCmap’ HGraf.c:92: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘theGC’ HGraf.c:93: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘gcs’ HGraf.c:95: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘*’ token HGraf.c:96: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘report’ HGraf.c:97: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘hints’ HGraf.c:111: error: ‘GXcopy’ undeclared here (not in a function) HGraf.c:111: error: ‘GXor’ undeclared here (not in a function) HGraf.c:111: error: ‘GXxor’ undeclared here (not in a function) HGraf.c:111: error: ‘GXinvert’ undeclared here (not in a function) HGraf.c:151: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘*’ token HGraf.c: In function ‘InstallFonts’: HGraf.c:164: error: ‘FontInfo’ undeclared (first use in this function) HGraf.c:164: error: (Each undeclared identifier is reported only once HGraf.c:164: error: for each function it appears in.) HGraf.c:164: warning: implicit declaration of function ‘XLoadQueryFont’ HGraf.c:164: error: ‘theDisp’ undeclared (first use in this function) HGraf.c:167: error: ‘DefaultFont’ undeclared (first use in this function) HGraf.c: At top level: HGraf.c:176: error: expected ‘)’ before ‘*’ token HGraf.c: In function ‘HGetEvent’: HGraf.c:219: error: ‘XEvent’ undeclared (first use in this function) HGraf.c:219: error: expected ‘;’ before ‘xev’ HGraf.c:223: warning: implicit declaration of function ‘XFlush’ HGraf.c:223: error: ‘theDisp’ undeclared (first use in this function) HGraf.c:225: warning: implicit declaration of function ‘XEventsQueued’ HGraf.c:225: error: ‘QueuedAfterFlush’ undeclared (first use in this function) HGraf.c:226: warning: implicit declaration of function ‘XNextEvent’ HGraf.c:226: error: ‘xev’ undeclared (first use in this function) HGraf.c:228: error: ‘theWindow’ undeclared (first use in this function) HGraf.c:230: error: ‘ButtonPress’ undeclared (first use in this function) HGraf.c:235: error: ‘ButtonRelease’ undeclared (first use in this function) HGraf.c:240: error: ‘MotionNotify’ undeclared (first use in this function) HGraf.c:245: error: ‘KeyPress’ undeclared (first use in this function) HGraf.c:249: warning: implicit declaration of function ‘DecodeKeyPress’ HGraf.c:251: error: ‘KeyRelease’ undeclared (first use in this function) HGraf.c:257: error: ‘Expose’ undeclared (first use in this function) HGraf.c: In function ‘HEventsPending’: HGraf.c:281: error: ‘theDisp’ undeclared (first use in this function) HGraf.c:281: error: ‘QueuedAfterFlush’ undeclared (first use in this function) HGraf.c: In function ‘HMousePos’: HGraf.c:288: error: ‘Window’ undeclared (first use in this function) HGraf.c:288: error: expected ‘;’ before ‘root’ HGraf.c:293: warning: implicit declaration of function ‘XQueryPointer’ HGraf.c:293: error: ‘theDisp’ undeclared (first use in this function) HGraf.c:293: error: ‘theWindow’ undeclared (first use in this function) HGraf.c:293: error: ‘root’ undeclared (first use in this function) HGraf.c:293: error: ‘child’ undeclared (first use in this function) HGraf.c: In function ‘InstallColours’: HGraf.c:311: error: ‘XColor’ undeclared (first use in this function) HGraf.c:311: error: expected ‘;’ before ‘greyDef’ HGraf.c:317: warning: implicit declaration of function ‘XParseColor’ HGraf.c:317: error: ‘theDisp’ undeclared (first use in this function) HGraf.c:317: error: ‘theCmap’ undeclared (first use in this function) HGraf.c:317: error: ‘colourDef’ undeclared (first use in this function) HGraf.c:320: warning: implicit declaration of function ‘XAllocColor’ HGraf.c:334: error: ‘whiteDef’ undeclared (first use in this function) HGraf.c:334: warning: implicit declaration of function ‘XQueryColor’ HGraf.c:335: error: ‘blackDef’ undeclared (first use in this function) HGraf.c:341: error: ‘greyDef’ undeclared (first use in this function) HGraf.c: In function ‘HSetColour’: HGraf.c:361: warning: implicit declaration of function ‘XSetForeground’ HGraf.c:361: error: ‘theDisp’ undeclared (first use in this function) HGraf.c:361: error: ‘gcs’ undeclared (first use in this function) HGraf.c: In function ‘HSetGrey’: HGraf.c:370: error: ‘theDisp’ undeclared (first use in this function) HGraf.c:370: error: ‘gcs’ undeclared (first use in this function) HGraf.c: In function ‘HDrawLines’: HGraf.c:388: warning: implicit declaration of function ‘XDrawLines’ HGraf.c:388: error: ‘theDisp’ undeclared (first use in this function) HGraf.c:388: error: ‘theWindow’ undeclared (first use in this function) HGraf.c:388: error: ‘theGC’ undeclared (first use in this function) HGraf.c:388: error: ‘XPoint’ undeclared (first use in this function) HGraf.c:388: error: expected expression before ‘)’ token HGraf.c: In function ‘HDrawRectangle’: HGraf.c:395: warning: implicit declaration of function ‘XDrawRectangle’ HGraf.c:395: error: ‘theDisp’ undeclared (first use in this function) HGraf.c:395: error: ‘theWindow’ undeclared (first use in this function) HGraf.c:395: error: ‘theGC’ undeclared (first use in this function) HGraf.c: In function ‘HFillRectangle’: HGraf.c:402: warning: implicit declaration of function ‘XFillRectangle’ HGraf.c:402: error: ‘theDisp’ undeclared (first use in this function) HGraf.c:402: error: ‘theWindow’ undeclared (first use in this function) HGraf.c:402: error: ‘theGC’ undeclared (first use in this function) HGraf.c: In function ‘HDrawLine’: HGraf.c:408: warning: implicit declaration of function ‘XDrawLine’ HGraf.c:408: error: ‘theDisp’ undeclared (first use in this function) HGraf.c:408: error: ‘theWindow’ undeclared (first use in this function) HGraf.c:408: error: ‘theGC’ undeclared (first use in this function) HGraf.c: In function ‘HFillPolygon’: HGraf.c:414: warning: implicit declaration of function ‘XFillPolygon’ HGraf.c:414: error: ‘theDisp’ undeclared (first use in this function) HGraf.c:414: error: ‘theWindow’ undeclared (first use in this function) HGraf.c:414: error: ‘theGC’ undeclared (first use in this function) HGraf.c:414: error: ‘XPoint’ undeclared (first use in this function) HGraf.c:414: error: expected expression before ‘)’ token HGraf.c: In function ‘HDrawArc’: HGraf.c:427: warning: implicit declaration of function ‘XDrawArc’ HGraf.c:427: error: ‘theDisp’ undeclared (first use in this function) HGraf.c:427: error: ‘theWindow’ undeclared (first use in this function) HGraf.c:427: error: ‘theGC’ undeclared (first use in this function) HGraf.c: In function ‘HFillArc’: HGraf.c:440: warning: implicit declaration of function ‘XFillArc’ HGraf.c:440: error: ‘theDisp’ undeclared (first use in this function) HGraf.c:440: error: ‘theWindow’ undeclared (first use in this function) HGraf.c:440: error: ‘theGC’ undeclared (first use in this function) HGraf.c: In function ‘HPrintf’: HGraf.c:451: warning: implicit declaration of function ‘XDrawString’ HGraf.c:451: error: ‘theDisp’ undeclared (first use in this function) HGraf.c:451: error: ‘theWindow’ undeclared (first use in this function) HGraf.c:451: error: ‘theGC’ undeclared (first use in this function) HGraf.c: In function ‘HCopyArea’: HGraf.c:457: warning: implicit declaration of function ‘XCopyArea’ HGraf.c:457: error: ‘theDisp’ undeclared (first use in this function) HGraf.c:457: error: ‘theWindow’ undeclared (first use in this function) HGraf.c:457: error: ‘theGC’ undeclared (first use in this function) HGraf.c: In function ‘HPlotVector’: HGraf.c:476: error: ‘theDisp’ undeclared (first use in this function) HGraf.c:476: error: ‘theWindow’ undeclared (first use in this function) HGraf.c:476: error: ‘theGC’ undeclared (first use in this function) HGraf.c: In function ‘HSetFontSize’: HGraf.c:490: error: ‘CurrentFont’ undeclared (first use in this function) HGraf.c:490: error: ‘DefaultFont’ undeclared (first use in this function) HGraf.c:499: error: ‘FontInfo’ undeclared (first use in this function) HGraf.c:502: warning: implicit declaration of function ‘XSetFont’ HGraf.c:502: error: ‘theDisp’ undeclared (first use in this function) HGraf.c:502: error: ‘gcs’ undeclared (first use in this function) HGraf.c: In function ‘HSetLineWidth’: HGraf.c:511: warning: implicit declaration of function ‘XSetLineAttributes’ HGraf.c:511: error: ‘theDisp’ undeclared (first use in this function) HGraf.c:511: error: ‘gcs’ undeclared (first use in this function) HGraf.c:511: error: ‘LineSolid’ undeclared (first use in this function) HGraf.c:511: error: ‘JoinRound’ undeclared (first use in this function) HGraf.c:511: error: ‘FillSolid’ undeclared (first use in this function) HGraf.c: In function ‘HSetXMode’: HGraf.c:517: error: ‘theGC’ undeclared (first use in this function) HGraf.c:517: error: ‘gcs’ undeclared (first use in this function) HGraf.c: In function ‘CentreX’: HGraf.c:523: warning: implicit declaration of function ‘XTextWidth’ HGraf.c:523: error: ‘CurrentFont’ undeclared (first use in this function) HGraf.c: In function ‘CentreY’: HGraf.c:529: error: ‘CurrentFont’ undeclared (first use in this function) HGraf.c: In function ‘HTextWidth’: HGraf.c:535: error: ‘CurrentFont’ undeclared (first use in this function) HGraf.c: In function ‘HTextHeight’: HGraf.c:541: error: ‘CurrentFont’ undeclared (first use in this function) HGraf.c: In function ‘HDrawImage’: HGraf.c:550: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘*’ token HGraf.c:550: error: ‘xi’ undeclared (first use in this function) HGraf.c:557: warning: implicit declaration of function ‘XDestroyImage’ HGraf.c:558: warning: implicit declaration of function ‘XGetImage’ HGraf.c:558: error: ‘theDisp’ undeclared (first use in this function) HGraf.c:558: error: ‘theWindow’ undeclared (first use in this function) HGraf.c:558: error: ‘AllPlanes’ undeclared (first use in this function) HGraf.c:558: error: ‘XYPixmap’ undeclared (first use in this function) HGraf.c:562: warning: implicit declaration of function ‘XPutPixel’ HGraf.c:564: warning: implicit declaration of function ‘XPutImage’ HGraf.c:564: error: ‘theGC’ undeclared (first use in this function) HGraf.c: In function ‘HFlush’: HGraf.c:570: error: ‘theDisp’ undeclared (first use in this function) HGraf.c: In function ‘InitGCs’: HGraf.c:780: error: ‘XGCValues’ undeclared (first use in this function) HGraf.c:780: error: expected ‘;’ before ‘values’ HGraf.c:783: error: ‘GCLineWidth’ undeclared (first use in this function) HGraf.c:783: error: ‘GCFunction’ undeclared (first use in this function) HGraf.c:783: error: ‘GCForeground’ undeclared (first use in this function) HGraf.c:785: error: ‘values’ undeclared (first use in this function) HGraf.c:788: error: ‘gcs’ undeclared (first use in this function) HGraf.c:788: warning: implicit declaration of function ‘XCreateGC’ HGraf.c:788: error: ‘theDisp’ undeclared (first use in this function) HGraf.c:788: error: ‘theWindow’ undeclared (first use in this function) HGraf.c:790: error: ‘GCPlaneMask’ undeclared (first use in this function) HGraf.c: In function ‘InitGlobals’: HGraf.c:800: warning: implicit declaration of function ‘DefaultScreen’ HGraf.c:800: error: ‘theDisp’ undeclared (first use in this function) HGraf.c:801: error: ‘theCmap’ undeclared (first use in this function) HGraf.c:801: warning: implicit declaration of function ‘DefaultColormap’ HGraf.c:802: error: ‘rootW’ undeclared (first use in this function) HGraf.c:802: warning: implicit declaration of function ‘RootWindow’ HGraf.c:803: error: ‘theGC’ undeclared (first use in this function) HGraf.c:803: warning: implicit declaration of function ‘DefaultGC’ HGraf.c:804: error: ‘theVisual’ undeclared (first use in this function) HGraf.c:804: warning: implicit declaration of function ‘DefaultVisual’ HGraf.c:805: warning: implicit declaration of function ‘DisplayCells’ HGraf.c:806: warning: implicit declaration of function ‘DisplayWidth’ HGraf.c:807: warning: implicit declaration of function ‘DisplayHeight’ HGraf.c:808: warning: implicit declaration of function ‘DisplayPlanes’ HGraf.c:809: warning: implicit declaration of function ‘WhitePixel’ HGraf.c:810: warning: implicit declaration of function ‘BlackPixel’ HGraf.c: In function ‘MakeXGraf’: HGraf.c:817: error: ‘Window’ undeclared (first use in this function) HGraf.c:817: error: expected ‘;’ before ‘window’ HGraf.c:818: error: ‘XSetWindowAttributes’ undeclared (first use in this function) HGraf.c:818: error: expected ‘;’ before ‘setwinattr’ HGraf.c:823: error: ‘theDisp’ undeclared (first use in this function) HGraf.c:823: warning: implicit declaration of function ‘XOpenDisplay’ HGraf.c:824: warning: implicit declaration of function ‘XDisplayName’ HGraf.c:828: error: ‘parent’ undeclared (first use in this function) HGraf.c:829: error: ‘window’ undeclared (first use in this function) HGraf.c:829: warning: implicit declaration of function ‘XCreateSimpleWindow’ HGraf.c:831: error: ‘CWBackingStore’ undeclared (first use in this function) HGraf.c:831: error: ‘setwinattr’ undeclared (first use in this function) HGraf.c:831: error: ‘WhenMapped’ undeclared (first use in this function) HGraf.c:832: warning: implicit declaration of function ‘XChangeWindowAttributes’ HGraf.c:834: error: ‘hints’ undeclared (first use in this function) HGraf.c:834: error: ‘PPosition’ undeclared (first use in this function) HGraf.c:834: error: ‘PSize’ undeclared (first use in this function) HGraf.c:834: error: ‘PMaxSize’ undeclared (first use in this function) HGraf.c:834: error: ‘PMinSize’ undeclared (first use in this function) HGraf.c:841: warning: implicit declaration of function ‘XSetStandardProperties’ HGraf.c:841: error: ‘None’ undeclared (first use in this function) HGraf.c:843: warning: implicit declaration of function ‘XSelectInput’ HGraf.c:843: error: ‘ExposureMask’ undeclared (first use in this function) HGraf.c:843: error: ‘KeyPressMask’ undeclared (first use in this function) HGraf.c:843: error: ‘ButtonPressMask’ undeclared (first use in this function) HGraf.c:844: error: ‘ButtonReleaseMask’ undeclared (first use in this function) HGraf.c:844: error: ‘PointerMotionHintMask’ undeclared (first use in this function) HGraf.c:844: error: ‘PointerMotionMask’ undeclared (first use in this function) HGraf.c:845: warning: implicit declaration of function ‘XMapWindow’ HGraf.c:845: error: ‘theWindow’ undeclared (first use in this function) HGraf.c:850: error: ‘report’ undeclared (first use in this function) HGraf.c:851: error: ‘Expose’ undeclared (first use in this function) HGraf.c:852: warning: implicit declaration of function ‘XSendEvent’ HGraf.c:852: error: ‘False’ undeclared (first use in this function) HGraf.c: In function ‘TermHGraf’: HGraf.c:861: error: ‘theDisp’ undeclared (first use in this function) HGraf.c:862: warning: implicit declaration of function ‘XCloseDisplay’ make[1]: *** [HGraf.o] Error 1 make[1]: Leaving directory/home/charles/bin/htk-3.4/HTKLib' make: ** [HTKLib/HTKLib.a] Error 1 Thank you for any help you can provide.

  Read the article

• Best way to handle huge strings in c#

  - by srk

  I have to write the data below to a textfile after replacing two values with ##IP##, ##PORT##. what is the best way ? should i hold all in a string and use Replace and write to textfile ? Data : [APP] iVersion= 101 pcVersion=1.01a pcBuildDate=Mar 27 2009 [MAIN] iFirstSetup= 0 rcMain.rcLeft= 676 rcMain.rcTop= 378 rcMain.rcRight= 1004 rcMain.rcBottom= 672 iShowLog= 0 iMode= 1 [GENERAL] iTips= 1 iTrayAnimation= 1 iCheckColor= 1 iPriority= 1 iSsememcpy= 1 iAutoOpenRecv= 1 pcRecvPath=C:\Documents and Settings\karthikeyan\My Documents\Downloads\fremote101a\FantasyRemote101a\recv pcFileName=FantasyRemote iLanguage= 1 [SERVER] iAcceptVideo= 1 iAcceptAudio= 1 iAcceptInput= 1 iAutoAccept= 1 iAutoTray= 0 iConnectSound= 1 iEnablePassword= 0 pcPassword= pcPort=7902 [CLIENT] iAutoConnect= 0 pcPassword= pcDefaultPort=7902 [NETWORK] pcConnectAddr=##IP## pcPort=##Port## [VIDEO] iEnable= 1 pcFcc=AMV3 pcFccServer= pcDiscription= pcDiscriptionServer= iFps= 30 iMouse= 2 iHalfsize= 0 iCapturblt= 0 iShared= 0 iSharedTime= 5 iVsync= 1 iCodecSendState= 1 iCompress= 2 pcPlugin= iPluginScan= 0 iPluginAspectW= 16 iPluginAspectH= 9 iPluginMouse= 1 iActiveClient= 0 iDesktop1= 1 iDesktop2= 2 iDesktop3= 0 iDesktop4= 3 iScan= 1 iFixW= 16 iFixH= 8 [AUDIO] iEnable= 1 iFps= 30 iVolume= 6 iRecDevice= 0 iPlayDevice= 0 pcSamplesPerSec=44100Hz pcChannels=2ch:Stereo pcBitsPerSample=16bit iRecBuffNum= 150 iPlayBuffNum= 4 [INPUT] iEnable= 1 iFps= 30 iMoe= 0 iAtlTab= 1 [MENU] iAlwaysOnTop= 0 iWindowMode= 0 iFrameSize= 4 iSnap= 1 [HOTKEY] iEnable= 1 key_IDM_HELP=0x00000070 mod_IDM_HELP=0x00000000 key_IDM_ALWAYSONTOP=0x00000071 mod_IDM_ALWAYSONTOP=0x00000000 key_IDM_CONNECT=0x00000072 mod_IDM_CONNECT=0x00000000 key_IDM_DISCONNECT=0x00000073 mod_IDM_DISCONNECT=0x00000000 key_IDM_CONFIG=0x00000000 mod_IDM_CONFIG=0x00000000 key_IDM_CODEC_SELECT=0x00000000 mod_IDM_CODEC_SELECT=0x00000000 key_IDM_CODEC_CONFIG=0x00000000 mod_IDM_CODEC_CONFIG=0x00000000 key_IDM_SIZE_50=0x00000074 mod_IDM_SIZE_50=0x00000000 key_IDM_SIZE_100=0x00000075 mod_IDM_SIZE_100=0x00000000 key_IDM_SIZE_200=0x00000076 mod_IDM_SIZE_200=0x00000000 key_IDM_SIZE_300=0x00000000 mod_IDM_SIZE_300=0x00000000 key_IDM_SIZE_400=0x00000000 mod_IDM_SIZE_400=0x00000000 key_IDM_CAPTUREWINDOW=0x00000077 mod_IDM_CAPTUREWINDOW=0x00000004 key_IDM_REGION=0x00000077 mod_IDM_REGION=0x00000000 key_IDM_DESKTOP1=0x00000078 mod_IDM_DESKTOP1=0x00000000 key_IDM_ACTIVE_MENU=0x00000079 mod_IDM_ACTIVE_MENU=0x00000000 key_IDM_PLUGIN=0x0000007A mod_IDM_PLUGIN=0x00000000 key_IDM_PLUGIN_SCAN=0x00000000 mod_IDM_PLUGIN_SCAN=0x00000000 key_IDM_DESKTOP2=0x00000078 mod_IDM_DESKTOP2=0x00000004 key_IDM_DESKTOP3=0x00000079 mod_IDM_DESKTOP3=0x00000004 key_IDM_DESKTOP4=0x0000007A mod_IDM_DESKTOP4=0x00000004 key_IDM_WINDOW_NORMAL=0x0000000D mod_IDM_WINDOW_NORMAL=0x00000004 key_IDM_WINDOW_NOFRAME=0x0000000D mod_IDM_WINDOW_NOFRAME=0x00000002 key_IDM_WINDOW_FULLSCREEN=0x0000000D mod_IDM_WINDOW_FULLSCREEN=0x00000001 key_IDM_MINIMIZE=0x00000000 mod_IDM_MINIMIZE=0x00000000 key_IDM_MAXIMIZE=0x00000000 mod_IDM_MAXIMIZE=0x00000000 key_IDM_REC_START=0x00000000 mod_IDM_REC_START=0x00000000 key_IDM_REC_STOP=0x00000000 mod_IDM_REC_STOP=0x00000000 key_IDM_SCREENSHOT=0x0000002C mod_IDM_SCREENSHOT=0x00000002 key_IDM_AUDIO_MUTE=0x00000073 mod_IDM_AUDIO_MUTE=0x00000004 key_IDM_AUDIO_VOLUME_DOWN=0x00000074 mod_IDM_AUDIO_VOLUME_DOWN=0x00000004 key_IDM_AUDIO_VOLUME_UP=0x00000075 mod_IDM_AUDIO_VOLUME_UP=0x00000004 key_IDM_CTRLALTDEL=0x00000023 mod_IDM_CTRLALTDEL=0x00000003 key_IDM_QUIT=0x00000000 mod_IDM_QUIT=0x00000000 key_IDM_MENU=0x0000007B mod_IDM_MENU=0x00000000 [OVERLAY] iIndicator= 1 iAlphaBlt= 1 iEnterHide= 0 pcFont=MS UI Gothic [AVI] iSound= 1 iFileSizeLimit= 100000 iPool= 4 iBuffSize= 32 iStartDiskSpaceCheck= 1 iStartDiskSpace= 1000 iRecDiskSpaceCheck= 1 iRecDiskSpace= 100 iCache= 0 iAutoOpen= 1 pcPath=C:\Documents and Settings\karthikeyan\My Documents\Downloads\fremote101a\FantasyRemote101a\avi [SCREENSHOT] iSound= 1 iAutoOpen= 1 pcPath=C:\Documents and Settings\karthikeyan\My Documents\Downloads\fremote101a\FantasyRemote101a\ss pcPlugin=BMP [CDLG_SERVER] mrcWnd.rcLeft= 667 mrcWnd.rcTop= 415 mrcWnd.rcRight= 1013 mrcWnd.rcBottom= 634 [CWND_CLIENT] miShowLog= 0 m_iOverlayLock= 0 [CDLG_CONFIG] mrcWnd.rcLeft= 467 mrcWnd.rcTop= 247 mrcWnd.rcRight= 1213 mrcWnd.rcBottom= 802 miTabConfigSel= 2

  Read the article

• Android :WindowManager$BadTockenException on Spinner Click

  - by Miya

  Hi, I have a spinner in my home.class. When I click on the spinner, the process is stopped showing exception that WindowManager$BadTockenException is caught. I am calling this home.class from main.class which extends ActivityGroup. If I am simply run only the home.class, the spinner is showing all items. But the problem is only with calling home.class from main.class. The following are my code. Please tell me why this is happened. main.class public class main extends ActivityGroup { public void onCreate(Bundle savedInstanceState) { super.onCreate(savedInstanceState); Intent intent=new Intent(this,home.class); View view=getLocalActivityManager().startActivity("1", intent.addFlags(Intent.FLAG_ACTIVITY_CLEAR_TOP)).getDecorView(); setContentView(view); } } home.class String[] country={"Please selects","US","INDIA","UK"}; Spinner s2 = (Spinner) findViewById(R.id.spinnerCountry); ArrayAdapter<CharSequence> adapterCountry=new ArrayAdapter(this,android.R.layout.simple_spinner_item,country); adapterCountry.setDropDownViewResource(android.R.layout.simple_spinner_dropdown_item); s2.setAdapter(adapterCountry); s2.setOnItemSelectedListener(new OnItemSelectedListener() { public void onItemSelected( AdapterView<?> parent, View view, int position, long id) { countryName=country[position]; } public void onNothingSelected(AdapterView<?> parent) { countryName=country[0]; } }); Stack Thread [<1 main] (Suspended (exception WindowManager$BadTokenException)) AlertDialog(Dialog).show() line: 245 AlertDialog$Builder.show() line: 802 Spinner.performClick() line: 260 View$PerformClick.run() line: 9080 ViewRoot(Handler).handleCallback(Message) line: 587 ViewRoot(Handler).dispatchMessage(Message) line: 92 Looper.loop() line: 123 ActivityThread.main(String[]) line: 3647 Method.invokeNative(Object, Object[], Class, Class[], Class, int, boolean) line: not available [native method] Method.invoke(Object, Object...) line: 507 ZygoteInit$MethodAndArgsCaller.run() line: 839 ZygoteInit.main(String[]) line: 597 NativeStart.main(String[]) line: not available [native method] Thank You....

  Read the article

• Programmatically setup a PEAP connection in Windows Mobile

  - by tomlog

  I have been working on this for a few days and this is doing my head in: Our application is built using the .NET Compact Framework 2.0 and running on Windows Mobile 5 & 6 devices. We can set the WLAN connection of the device programmatically using the Wireless Zero Config functions (described here: msdn.microsoft.com/en-us/library/ms894771.aspx), most notably the WZCSetInterface function which we pinvoke from our application. This works fine for WEP and WPA-PSK connections. In a recent effort to add support for WPA2 networks we decided to modify the code. We have successfully added support for WPA2 which uses a certificate for the 802.1x authentication by setting the correct registry settings before calling WZCSetInterface. Now we want to do the same for WPA2 using PEAP (MS-CHAPv2) authentication. When manually creating such a connection in Windows Mobile the user will be prompted to enter the domain/user/password details. In our application we will have those details stored locally and want to do this all programmatically without any user intervention. So I thought going along the same route as the certificate authentication, setting the correct registry entries before calling WZCSetInterface. The registry settings we set are: \HKCU\Comm\EAP\Config\[ssid name] Enable8021x = 1 (DWORD) LastAuthSuccessful = 1 (DWORD) EapTypeId = 25 (DWORD) Identity = "domain\username" (string) Password = binary blob containing the password that is encrypted using the CryptProtectData function (described here: msdn.microsoft.com/en-us/library/ms938309.aspx) But when these settings are set and I call WZCSetInterface with the correct parameters, it still prompts me with the User Logon dialog asking for the domain/username/password. Has anyone got an idea what I need to do to prevent the password dialog from appearing and connect straight away with the settings stored in the registry?

  Read the article

• Graphics driver for ubuntu on dell latitude XT

  - by marc.riera

  Hi, we have a laptop (dell latitude xt) on our company, and we would like to install ubuntu on it. windows 7 works fine out of the box, so the hardware is fine. since this laptop has a touchscreen we just installed ubuntu 10.10 netbook edition 32x. But, we do not manage to enable the touchscreen, neither the vga graphic drivers. this is the output from lspci, if somebody cares. 00:00.0 Host bridge: ATI Technologies Inc Radeon Xpress 7930 Host Bridge 00:01.0 PCI bridge: ATI Technologies Inc RS7932 PCI Bridge 00:04.0 PCI bridge: ATI Technologies Inc Device 7934 00:06.0 PCI bridge: ATI Technologies Inc RS7936 PCI Bridge 00:07.0 PCI bridge: ATI Technologies Inc Device 7937 00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0) 00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1) 00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2) 00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3) 00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4) 00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI) 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 14) 00:14.1 IDE interface: ATI Technologies Inc SB600 IDE 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 01:05.0 VGA compatible controller: ATI Technologies Inc Radeon Xpress 1250 03:01.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller 03:01.1 FireWire (IEEE 1394): Texas Instruments PCIxx12 OHCI Compliant IEEE 1394 Host Controller 03:01.3 SD Host controller: Texas Instruments PCIxx12 SDA Standard Compliant SD Host Controller 09:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5756ME Gigabit Ethernet PCI Express 0b:00.0 Network controller: Broadcom Corporation BCM4321 802.11a/b/g/n (rev 03) I've tryied to install ati drivers 9.3 , which I downloaded and installed, unpacked and installed, builded and installed, but nothing worked. Looks like the latests version is just accepted to work on jaunty 9.04, so they are kind of old. what else I can do? thanks. Marc Information added: lsusb and lspci -n |grep 01:05.0 sysop@wl083517:~$ lspci -n |grep 01:05.0 01:05.0 0300: 1002:7942 sysop@wl083517:~$ lsusb Bus 006 Device 002: ID 413c:8138 Dell Computer Corp. Wireless 5520 Voda I Mobile Broadband (3G HSDPA) Minicard EAP-SIM Port Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 002: ID 413c:8140 Dell Computer Corp. Wireless 360 Bluetooth Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 002: ID 0483:2016 SGS Thomson Microelectronics Fingerprint Reader Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 002: ID 1b96:0001 N-Trig Duosense Transparent Electromagnetic Digitizer Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 002: ID 03f0:1807 Hewlett-Packard Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub sysop@wl083517:~$

  Read the article

• Windows 2008 R2 CA and auto-enrollment: how to get rid of >100,000 issued certificates?

  - by HopelessN00b

  The basic problem I'm having is that I have 100,000 useless machine certificates cluttering up my CA, and I'd like to delete them, without deleting all certs, or time jumping the server ahead, and invalidating some of the useful certs on there. This came about as a result of accepting a couple defaults with our Enterprise Root CA (2008 R2) and using a GPO to auto-enroll client machines for certificates to allow 802.1x authentication to our corporate wireless network. Turns out that the default Computer (Machine) Certificate Template will happily allow machines to re-enroll instead of directing them to use the certificate they already have. This is creating a number of problems for the guy (me) who was hoping to use the Certificate Authority as more than a log of every time a workstation's been rebooted. (The scroll bar on the side is lying, if you drag it to the bottom, the screen pauses and loads the next few dozen certs.) Does anyone know how to DELETE 100,000 or so time-valid, existing certificates from a Windows Server 2008R2 CA? When I go to delete a certificate now, now, I get an error that it cannot be delete because it's still valid. So, ideally, some way to temporarily bypass that error, as Mark Henderson's provided a way to delete the certificates with a script once that hurdle is cleared. (Revoking them is not an option, as that just moves them to Revoked Certificates, which we need to be able to view, and they can't be deleted from the revoked "folder" either.) Update: I tried the site @MarkHenderson linked, which is promising, and offers much better certificate manageability, buts still doesn't quite get there. The rub in my case seems to be that the certificates are still "time-valid," (not yet expired) so the CA doesn't want to let them be deleted from existence, and this applies to revoked certs as well, so revoking them all and then deleting them won't work either. I've also found this technet blog with my Google-Fu, but unfortunately, they seemed to only have to delete a very large number of certificate requests, not actual certificates. Finally, for now, time jumping the CA forward so the certificates I want to get rid of expire, and therefore can be deleted with the tools at the site Mark linked is not a great option, as would expire a number of valid certificates we use that have to be manually issued. So it's a better option than rebuilding the CA, but not a great one.

  Read the article

• Linux Mint 14 severe overheating

  - by agvares

  I've tried switching to Mint (it was Mint 12) about 6 months ago, but failed to do it due to enormous overheating which made it virtually impossible to run any applications more complex than Gedit. Time had passed, and now I'm back again with Mint 14, but feeling way more determined. What I face are the following issues: 1) Great overheating (and by great I mean that just by doing nothing my CPU temp is floating around 70-75 C, which I find a lot) 2) Running multiple applications (let's say Chrome, Skype and Pidgin) results in critical overheating and immediate shutdown of the system 3) Due to the stuff listed above, my battery drains in about 10-15 minutes, pretty much turning my laptop into a crippled desktop machine I've got a HP-dv6 laptop (i7, 6gb RAM, dual graphics) Here's the output of lspci: 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) 00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b5) 00:1c.2 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 (rev b5) 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation HM65 Express Chipset Family LPC Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Whistler XT [AMD Radeon HD 6700M Series] 07:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) 0d:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) 13:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS5209 PCI Express Card Reader (rev 01) 19:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04) what i've tried to do already: 1) I've edited my grub file to add some "splash" arguments there 2) Installed jupiter and powertop 3) Tried to upgrade to newer kernels (up to 3.8), btw running anything newer than 3.5 results in both resolution and wi-fi detection fail 4) Read lots of forum threads devoted to the topic So, my question is simple: What else might I do to become finally able to use Mint as my default OS without the risk of being burned alive by the CPU heat?

  Read the article

• Graphics driver for ubuntu on dell latitude XT

  - by marc.riera

  we have a laptop (dell latitude xt) on our company, and we would like to install ubuntu on it. windows 7 works fine out of the box, so the hardware is fine. since this laptop has a touchscreen we just installed ubuntu 10.10 netbook edition 32x. But, we do not manage to enable the touchscreen, neither the vga graphic drivers. this is the output from lspci, if somebody cares. 00:00.0 Host bridge: ATI Technologies Inc Radeon Xpress 7930 Host Bridge 00:01.0 PCI bridge: ATI Technologies Inc RS7932 PCI Bridge 00:04.0 PCI bridge: ATI Technologies Inc Device 7934 00:06.0 PCI bridge: ATI Technologies Inc RS7936 PCI Bridge 00:07.0 PCI bridge: ATI Technologies Inc Device 7937 00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0) 00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1) 00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2) 00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3) 00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4) 00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI) 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 14) 00:14.1 IDE interface: ATI Technologies Inc SB600 IDE 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 01:05.0 VGA compatible controller: ATI Technologies Inc Radeon Xpress 1250 03:01.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller 03:01.1 FireWire (IEEE 1394): Texas Instruments PCIxx12 OHCI Compliant IEEE 1394 Host Controller 03:01.3 SD Host controller: Texas Instruments PCIxx12 SDA Standard Compliant SD Host Controller 09:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5756ME Gigabit Ethernet PCI Express 0b:00.0 Network controller: Broadcom Corporation BCM4321 802.11a/b/g/n (rev 03) I've tryied to install ati drivers 9.3 , which I downloaded and installed, unpacked and installed, builded and installed, but nothing worked. Looks like the latests version is just accepted to work on jaunty 9.04, so they are kind of old. what else I can do? thanks. Marc Information added: lsusb and lspci -n |grep 01:05.0 sysop@wl083517:~$ lspci -n |grep 01:05.0 01:05.0 0300: 1002:7942 sysop@wl083517:~$ lsusb Bus 006 Device 002: ID 413c:8138 Dell Computer Corp. Wireless 5520 Voda I Mobile Broadband (3G HSDPA) Minicard EAP-SIM Port Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 002: ID 413c:8140 Dell Computer Corp. Wireless 360 Bluetooth Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 002: ID 0483:2016 SGS Thomson Microelectronics Fingerprint Reader Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 002: ID 1b96:0001 N-Trig Duosense Transparent Electromagnetic Digitizer Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 002: ID 03f0:1807 Hewlett-Packard Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub sysop@wl083517:~$

  Read the article

• Windows 7 laptop constantly dropping internet connection

  - by Corbin Holbert

  I have scoured the web for an answer and failed to find one. I am using a Toshiba Satellite laptop running Windows 7 64-Bit. I have the computer connected via Wifi. Now, I am no beginner with the Internet, or anything related to computers, as I have grown up teaching everyone around me how to use computers, and went to college for IT. Everything on my network works flawlessly at all times, except for this evil laptop. The worst part is that I fixed this once before a few years back and recently had to replace the hard drive and re-install the OS, but cannot for the life of me remember what I did to make this problem go away. I am in my browser, connected to the Internet. I click a link. Suddenly no internet access. All I do is click down on the WiFi connection in the task bar, disconnect and reconnect immediately. Internet is back the moment I hit "connect." I have read many people had the same issues as I am having, but they all had triggers or other network issues. I have no trigger (this happens literally five to six times per minute no matter what I am doing) and I have no problems with my router, modem, or any other devices or computers on said network. As I am a web designer, and like to test my work live at every turn- this is going to result in this laptop being in pieces if I can't get it fixed soon. If more info is needed, let me know and I will provide. Thanks for any help offered! EDIT: Network Card: Realtek RTL8188CE Wireless LAN 802.11n PCI-E NIC Network state reads as "No Internet Access" when the problem first occurs, then magically I have Internet access for about ten seconds once I disconnect and reconnect. I have turned off IPV6, I have turned off power saving options for the network adapter, no viruses. Any new ideas? Also, I had to disconnect and reconnect four times just to get to this edit screen- and will likely have to do the same just to post it- it's that bad.

  Read the article

< Previous Page | 17 18 19 20 21 22 23 24  | Next Page >