Search Results

Search found 878 results on 36 pages for 'acts as revisable'.

Page 21/36 | < Previous Page | 17 18 19 20 21 22 23 24 25 26 27 28  | Next Page >

• Xen dom0 reports incorrect amount of RAM with dom0_mem set

  - by xen_amnesiac

  I've done a fair bit of searching about this, but have found nothing that answers my question. I have a system with 6GB of RAM which acts as a Xen server. For reference, it runs Ubuntu 12.04. I've set the kernel parameter dom0_mem:512M,max:512M in /etc/default/grub as follows: GRUB_CMDLINE_XEN_DEFAULT="dom0_mem=min:512M,max:512M" I've tried variations of that, with the same result. My question is this: With the above set, the dom0 reports in all applications a RAM amount of 422M. cat /proc/meminfo gives the following: $ cat /proc/meminfo MemTotal: 432472 kB MemFree: 54144 kB Buffers: 17640 kB Cached: 220104 kB SwapCached: 30172 kB Active: 136500 kB Inactive: 167780 kB Active(anon): 6156 kB Inactive(anon): 60516 kB Active(file): 130344 kB Inactive(file): 107264 kB Unevictable: 52 kB Mlocked: 52 kB SwapTotal: 1794044 kB SwapFree: 1682012 kB Dirty: 0 kB Writeback: 0 kB AnonPages: 39572 kB Mapped: 8048 kB Shmem: 136 kB Slab: 44324 kB SReclaimable: 22012 kB SUnreclaim: 22312 kB KernelStack: 1280 kB PageTables: 3840 kB NFS_Unstable: 0 kB Bounce: 0 kB WritebackTmp: 0 kB CommitLimit: 2010280 kB Committed_AS: 329192 kB VmallocTotal: 34359738367 kB VmallocUsed: 313988 kB VmallocChunk: 34359417340 kB HardwareCorrupted: 0 kB AnonHugePages: 0 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 HugePages_Surp: 0 Hugepagesize: 2048 kB DirectMap4k: 524696 kB DirectMap2M: 0 kB top, htop, free -m, and byobu's RAM monitor all report the same amount. At first I thought this was because of the onboard graphics borrowing some memory, but have now switched to a dedicated GPU and it persists. Is this normal behavior, or has something gone amiss? It's just about 100MB of RAM that's "gone", and I have no idea where it went. I understand that it's normal that not all RAM is available for allocation, but does the system really take an amount relatively high to the amount of RAM available?

  Read the article

• How do I keep folders synced and backed up between two macs using a Linux NAS (rsync?)

  - by Hultner

  I've got two primary computers, one Mac Pro and one MacBook Pro for when I'm on the go. I've also got a Linux sever which also acts as NAS. Currently I backup the entire computers to an external drive with Time Machine which is rather useless and doesn't sync anything. What I really want to do is to keep my important files synced between both computers and my NAS (which is running RAID 5), that way I'm not backing up easily replaceable systemfiles and I've got all my important files in 3 places where two of them are running raid so at least 5 drives would have to crash at the same time before actual data loss occur. Folders I want to keep synced is basically my photo, documents, development, mamp and work folders and then I want to keep the user library folder backed up but not synced. I'm thinking that I'd have to use rsync but don't know how. Before suggesting Dropbox and similar suggestions I don't want to use them because of several reasons some of them being security (Dropbox obviously proved this), Speed (sometimes I'll sync gigabytes of data and that will be significantly faster locally and probably even through VPN as I have a Gigabit pipe), Space (space on my NAS is cheap and only practically limited by my needs), reliability (even if my internet were to go down I still need to be able to keep my files synced incase I'd need to go somewhere on the fly), price (I already have all the hardware and for the amount of gigabytes and bandwidth I'd need I doubt that there's any free or cheap service). Those are my main reason for wanting to keep it locally. I'm sorry for any spelling or grammatical mistakes that I've might have done. I'm writing this on my smartphone from a shaky train and English isn't my mother tongue. I gratefully appreciate any answers even if only partly solving my problem.

  Read the article

• How to connect the virtual networks of vmware guests running on different hosts?

  - by gyrolf

  In a test setup, we are running several virtual machines on a single vmware workstation host. All virtual machines are connected via a "host only" network. This runs fine up to 2 or 3 virtual machines (depending on the host hardware). To allow more virtual machines, we want to use more host machines. Details about the environment and applications: Host PCs are running Windows XP in a corporate intranet. VMware used is Workstation 6.5 Guests are running Windows Server 2003 All guests act as Web Servers One of the guests additionally acts as Windows File server, offering shared folders for the other guests to connect to. Restrictions: VMware guests shall not be visible from the intranet. Changes to the host PC are restricted by corporate policy. In the virtual network, no domain controller exists. All virtual machines are member of the same workgroup. Running the virtual network as NAT is possible. Port forwarding might be used if it does not conflict with ports used by the host PC. Looking for a solution, I found hints about using router or vpn software on the hosts, but without any details how to setup. (I found a similar question Sharing the network between 2 VMware hosts, but the answer was not sufficient for me.)

  Read the article

• HTPC/DVR computer won't go into standby

  - by Robert

  When I select Start-Turn off computer-Standby the 'turn off computer' option window closes, and then nothing else happens. I can start new applications, and Windows acts like I never selected standby. I ran it for several hours after that. If I have a TV program scheduled to record when I select standby I get a window (the Pinnacle TV software) asking if I'm sure, there are programs scheduled to record - and the computer just keeps running after I select yes, never going into standby. I added that detail as it shows the standby process is starting. [This problem also happens if a TV program is not scheduled, so the scheduler task in not running/in memory. This problem happens regardless of whether I'm not watching TV. This problem happens regardless of whether Media Center is running (it usually isn't, I'm using Pinnacle to watch TV).] I looked at "How to troubleshoot hibernation and standby issues in Windows XP" http://support.microsoft.com/kb/907477 - ACPI is enabled, and "standby" is an option in "Power Options Properties." So it appears to be setup correctly. Windows XP SP3 Media Center Edition, all current updates installed.

  Read the article

• Windows SBS 2008 problem

  - by MadBoy

  I was today on clients site that has Windows 2008 SBS installed with Symantec EndPoint Protection. Problem is that after I logged in tried multiple commands like services.msc, msconfig typed in "Run" but nothing was started. For the first 5 minutes i can click around Start Menu, choose some applications (non microsoft works, even control panel works). But then something happens that I can't click where I want.. i can click on Start Menu and get it active but i cant choose anything from there, everything is like blocked, i can right click on Desktop i can do many things but most of the left clicks is blocked. Even when i start TaskMgr i am able to see it but I cannot click it, can't activate it or anything. It acts very very weird. It's newly installed system, with less then a month of when it was installed and it wasn't really used (been down most of the time). I suspect Symantec EndPoint protection might be faulty so when I go back there (Wednesday) I will uninstall it but maybe someone else have some ideas what may be happening. I doubt there's any virus or anything, symantec was installed right after setting everything up and running.

  Read the article

• Wireless USB keyboard and mouse can wake system, but then receiver is inactive

  - by BlueMonkMN

  I have a Microsoft brand USB device that acts as a receiver for a wireless Microsoft Keyboard and a wireless Mouse. When it's operating normally, there are LEDs on the device indicating Caps Lock, Num Lock and Function Lock, of which the latter 2 are usually lit. It is plugged into a Dell Isnpiron 531 with Windows 7 32-bit running on an AMD Athlon 64 X2 Dual Core processor 5000+. When the computer goes to sleep (the power indicator on the main box is flashing), I can wake it by moving the mouse. So far all is good. However, something changed in, I think, the past couple weeks (I suspect due to a Microsoft driver update problem). Before the change, after waking the computer, everything would operate normally as far as I could tell, but now after waking the computer, the receiver has no lights on, and the keyboard and mouse are completely unresponsive (which is odd, considering the mouse woke up the computer). There is a button on the receiver that's supposed to reset the wireless connection and flash the lights while it does so, but it has no effect in this state. It's like the receiver doesn't have power (but how would the system know I moved the mouse, unless the power was on until it woke up?). I have checked the BIOS/CMOS settings or whatever you call them, and did not see anything related to USB in the power management section. I have checked Windows 7 device manager and ensured that all the USB Root Hub devices have the setting unchecked for allowing the USB power to be turned off. Like I said, this was working before, and the only thing I can think of that's changed is applying Windows Updates.

  Read the article

• Kerberos service on win2k dc will not start following disk failure

  - by iwilson68

  Hi, I have a win2k (mixed mode domain) with 4 DCS. One of these also acts an exchange 2000 server which uses 2 logical volumes from an MSA 2000 array. AD etc is stored on local drives. We experienced a problem last week when the raid array fell back to a redundant controller and this temporarily meant that the two logical drives were not visible to the server for around 5 minutes and a couple of reboots. The log records these Events as Type: Warning Event Source: Disk Event Category: None Event ID: 51 Date: 06/11/2009 Time: 11:46:23 User: N/A Computer: server1 Description: An error was detected on device \Device\Harddisk1\DR1 during a paging operation. Following these problems, the server “kerberos Key Distribution” service refuses to start with an “error.31 a device attached to the system is not functioning”. All other automatic start services (including net logon) are running and there are no DNS issues etc. All devices are also functioning but the two logical MSA disks are now numbered in the Windows Disk Management MMC as 2 and 4 and I suspect that they may have previously been identified as disks 1 & 2 and perhaps windows still sees this as an ongoing failure?? Replication has not been affected but obviously there are many audit failures in the security log relating to users and workstations presumably linked to the Kerberos issue. Attempting to manually start the kerberos service generates the following in the System Log. Event Type: Error Event Source: Service Control Manager Event Category: None Event ID: 7023 Date: 09/11/2009 Time: 09:46:55 User: N/A Computer: Server1 Description: The Kerberos Key Distribution Center service terminated with the following error: A device attached to the system is not functioning. DCDIAG passes all tests except “Advertising” and “Services” which I believe relate directly to the failure of Kerberos only. Any advice would be appreciated.

  Read the article

• LSI 9260-8i w/ 6 256gb SSDs - RAID 5, 6, 10, or bad idea overall?

  - by Michael Pearson

  We're provisioning a new production server for our reasonably busy website. Our choice of host have available a 6 drive configuration with a LSI 9260-8i card. My initial thought was to fill all six bays with SSDs (Intel 520 256gb) and set them up in RAID. Good, bad, or terrible idea? Can the card handle it? Should we be using RAID 5, 6 or 10? This would be the first time the provider have filled all six slots for this rackmount with SSDs, so they're a bit hesitant. I'm wondering if somebody else with this card has done something similar in a production environment. We do about 43gb of writes per day and currently use about 300gb of storage. The server acts as webserver, database, and image store for approx 1 million files. The plan is to underprovision the SSDs by approximately 10% to 20% to increase their overall lifespan & performance. The fallback option is 2x480gb SSDs in RAID 1 and another 2x1TB HDDs in RAID 1. The motivation behind this is that the server rental cost difference between 2xSSDs and 6xSSDs is minimal (compared to the overall cost of the rental). We do not have any special high-IOPs requirements. However, if the configuration is known to work, I don't see a good reason to not use it and not have to worry about having separate 'fast and small' and 'slow and large' disks.

  Read the article

• I had a power outage. Now MySQL's lock file won't go away. What do you suggest?

  - by jasonspiro

  I do freelance IT consulting for various clients, both in Toronto, Canada, and worldwide. A client recently experienced a power failure. Now they've been having various problems with a Slackware 12.0.0 machine which also acts as a DNS server. One problem is that they can't log into phpMyAdmin. I tried stopping and restarting MySQL. But even when MySQL is stopped, the lock file stays around. jasonspiro@cybertron:~$ sudo /etc/init.d/mysql stop Shutting down MySQL. SUCCESS! jasonspiro@cybertron:~$ sudo /etc/init.d/mysql stop ERROR! MySQL manager or server PID file could not be found! jasonspiro@cybertron:~$ sudo /etc/init.d/mysql status ERROR! MySQL is not running, but lock exists jasonspiro@cybertron:~$ ls -l /var/lock/subsys/mysql -rw-r--r-- 1 root root 0 2012-07-05 16:18 /var/lock/subsys/mysql Why is MySQL's lock file hanging around despite the fact that MySQL isn't running? Can I simply stop MySQL, delete the lock file, and start MySQL again? Are there any other steps that I should take next, or nothing?

  Read the article

• Setup a new domain controller over a temporary VPN, but now Windows delays startup?

  - by Kris Anderson

  I'm migrating servers from colo locations to Amazon's VPC EC2 instances. If anyone hasn't worked with Amazon VPC before, VPN is a pain in the arse! Anyways, I setup a new server that acts as the domain controller for our Amazon VPC. In order to migrate all the user accounts from our existing domain controllers I manually connected to our colo VPN using my user account on the new Amazon EC2 machine. I was able to join the domain and the new Amazon server became another domain controller on our network. So far so good. The problem I'm having is that when booting the EC2 domain controller (which is no longer connected to the VPN so it can't communicate with the existing controllers), it takes a good 6-8 minuted before I can remote into the server (instead of the 1-2 minutes it should take). Also, during this time most of the services we also run (like IIS) also give 404 errors until the 6-8 minutes have passed. It's almost like the domain controller is attempting to reach the other domain controllers first and after 6-8 minutes it falls back to the one located on the local machine? I don't think that's what's happening though, because Server 2008 R2 doesn't have primary and backup domain controllers. They're all equal as far as Windows is concerned. For my network adapter I have only one DNS listed, 127.0.0.1, so it should be looking up the local domain controller and not the other domain controllers it connected to over VPN when VPN was enabled. In the server logs I'm seeing these warnings pop up during a reboot: The winlogon notification subscriber is taking long time to handle the notification event (CreateSession). The winlogon notification subscriber took 409 second(s) to handle the notification event (CreateSession). Any ideas on what's happening here? I would try removing the existing domain controllers from the new Amazon EC2 machine, but I still need to connect over VPN a few times to migrate some data between the servers, and I don't want that change being reflected back to the other domain controllers in our colo locations.

  Read the article

• How to copy a bunch of pages? Is there a 3rd party tool?

  - by unknown (yahoo)

  (I asked the following question at the DNN forum, and also at snowcovered. Nobody knew of such an obvious time-saver being for sale. I'm posting here in case anybody knows of a freeware module that might do this.) By "groups of dnn pages", I mean pages that form a hierarchy (not necessary a hierarchy that is headed with a page at the same level as the Home page.) I know that I can copy web pages, one by one, using the admin login via the web-based dnn interface. But, I'd prefer a script or wizard, of some sort (that runs scripts behind the scenes) that can allow me to 1) specify a web page that I want to copy (along with the hierarchy of pages under it) 2) specify the names and titles of the new top-level pages 3) specify whether the contained modules of the top-level page that I want to copy is to be : ( ) New ( ) Copy ( ) Reference (as in the web-based interface) 4) repeat 3) for each of the source pages in the hierarchy that I want to copy You might say that I am looking to do something similar to creating a portal web site based on a template, except that it's not an entirely new website - instead it's a section of the current web site. I might want to do this because I have an organization which is broken into chapters, and I want each chapter to have, say, it's own General Information page (which acts like it's home page), and underneath that, in it's hierarchy, a Contact Info page and an Events page. so: Home Page   General Information Page     Contact Info     Events -- Home Page   General Information Page     Contact Info     Events   General Information Page Kiwanis - Bloomfield     Contact Info     Events   General Information Page Kiwanis - Dayton     Contact Info     Events If I have 200 chapters, I certainly don't want to copy those 3 web pages using the web based interface, as that would take a long time. (And imagine if each chapter's new sub-website had 30 pages!) I just want to specify the parameters of a copy process, then press a button, and let the system do the rest.

  Read the article

• Some URLs fail to load on Windows web portal

  - by jpolache

  I’m working in a large data center and have been assigned to troubleshoot and issue with a windows (IIS) web server that acts as a portal for a customer of the data center. This portal server is on a DMZ at the local data center. I don’t have access to the portal desktop and am relying on an off-site administrator to work with me to do testing and report the condition of the portal. He tells me there are no software firewalls or other filtering configured. While most of the remote web pages work fine, several of the URSs the portal is suppose to serve up fail to load. I had wireshark installed on the portal system and had a capture taken of one of the failures. I used IE to access one of the remote web servers at issue. I could see the TCP SYN-ACK coming back from the remote server, but after several HTTP GETs fail to get a response the portal server sends a reset. The webmaster of the remote web server assures me that no sites are being blocked. I had a capture taken outside the local firewall, so there should be no issue there. Another tech set up a laptop and used the IP address of the portal (we took the portal off-line for the test). The laptop loads the URL as expected. I tried having Firefox loaded to make sure that the HTTP GET was not mal-formed. Same failure as with IE. So, it seems it is not the remote web server or the network, because there was no problem with the laptop. At this point, I’m not sure what other questions to ask or tests to do.

  Read the article

• Dell PERC 5 - RAID-10 keeps rebuilding drive 2 every day

  - by raid question

  I have a Dell PowerEdge 2950 with this card: RAID bus controller [0104]: Dell PowerEdge Expandable RAID controller 5 [1028:0015] and six disks in a RAID-10. I replaced drive 2, because it didn't show up, and then it started to rebuild itself: root@backup01:~# megaraidsas-status -- Arrays informations -- -- ID | Type | Size | Status a0d0 | RAID 10 | 5587GiB | DEGRADED -- Disks informations -- ID | Model | Status | Warnings a0e8s0 | ATA ST2000DM001-9YN1 1863GiB | online | errs: media:0 other:5393 a0e8s1 | ATA ST2000DM001-9YN1 1863GiB | online | errs: media:0 other:5394 a0e8s2 | ATA ST2000DM001-1E61 1863GiB | rebuild | errs: media:0 other:99 a0e8s3 | ATA ST2000DM001-9YN1 1863GiB | online | errs: media:0 other:5393 a0e8s4 | ATA ST2000DM001-9YN1 1863GiB | online | errs: media:0 other:5393 a0e8s5 | ATA ST2000DM001-9YN1 1863GiB | online | errs: media:0 other:5393 The rebuild finishes, then the virtual drive becomes optimal, and drive 2 goes online. Then once a day, drive 2 acts like it's been removed, and the rebuild starts all over again. How do I make this once a day rebuild stop? Event Description: Removed: PD 02(e1/s2) Event Description: Removed: PD 02(e1/s2) Info: enclPd=08, scsiType=0, portMap=04, sasAddr=1221000002000000,0000000000000000 Event Description: State change on VD 00/0 from OPTIMAL(3) to DEGRADED(2) Event Description: VD 00/0 is now DEGRADED1 Event Description: State change on PD 02(e1/s2) from ONLINE(18) to FAILED(11) Event Description: State change on PD 02(e1/s2) from FAILED(11) to UNCONFIGURED_BAD(1) Event Description: Background Initialization failed on VD 00/0 Event Description: Inserted: PD 02(e1/s2) Event Description: Inserted: PD 02(e1/s2) Info: enclPd=08, scsiType=0, portMap=04, sasAddr=1221000002000000,0000000000000000 Event Description: PD 02(e1/s2) is not a certified drive Event Description: State change on PD 02(e1/s2) Event Description: State change on PD 02(e1/s2) from UNCONFIGURED_GOOD(0) to OFFLINE(10) from UNCONFIGURED_BAD(1) to UNCONFIGURED_GOOD(0) Event Description: Rebuild automatically started on PD 02(e1/s2) Event Description: State change on PD 02(e1/s2) from OFFLINE(10) to REBUILD(14)

  Read the article

• Windows Home Server installation fails because it can't find the DVD drive anymore

  - by BBlake

  I've got an old Dell Dimension 8300 desktop I decided to convert into a WHS box. I popped in a pair of 1 TB SATA drives, which were recognized fine by the BIOS and the currently installed OS (XP), so I decided to go ahead and install WHS. Near the end of the installation, WHS acts like it can no longer find the DVD drives (either of them, the box has a DVDROM and a DVDRW). The specific error is gives is the "Can't configure storage" error. I've found several forums where people say they get this error if they remove the boot DVD during the installation (at the time of the first reboot). However, I never removed the DVD. After the error, if fails into WHS, so it did mostly install and I can work with WHS. However, it refuses to recognize the network card, video card and while it shows the two DVD drives, any CD/DVD I insert in either drive the system says is corrupted and unreadable, even though none of them are. I've tried several reinstalls both removing and not removing the DVD, but the result is the same regardless. Any other tricks anyone found? If I can't figure this out, maybe I'll just install SBS2008 and fake it up to be similar to WHS with some addin tools. Shouldn't be too hard to create something since WHS is based on SBS2003 anyway.

  Read the article

• 3 Servers, is this is a cluster?

  - by Andy Barlow

  Hello, At the moment I have one Ubuntu server, 9.10, running with a simple Samba share, a mail server, DNS server and DHCP server. Mostly its just there for file sharing and email server. I also have 2 other servers that are exactly the same hardware and spec as the first, which have an rsync set up to retrieve the shared folders and backs them up. However, if the first server goes down, all of our shares disappear along with our mail and the system must be rebuilt. Also I tend to find if people are downloading a large amount from the file server, no-one can access there emails - especially in the morning when everyone is signing in at once. Would it be more beneficial for me to have all 3 servers, all running the same services, doing the same thing with some sort of cluster with load balancing? I'm not really sure where to begin looking, or how to go about such a setup where 3 servers are all identical, but perhaps one acts as the main load balancer?? If someone can point me in the right direction, or if this simply sounds like one of those Enterprise Cloud's that is now a default setup in Ubuntu Server 9.10+, then I'll go down that route. Cheers in advance. Andy

  Read the article

• TV won't go into standby

  - by Robert

  When I select Start-Turn off computer-Standby the 'turn off computer' option window closes, and then nothing else happens. I can start new applications, and Windows acts like I never selected standby. I ran it for several hours after that. If I have a TV program scheduled to record when I select standby I get a window (the Pinnacle TV software) asking if I'm sure, there are programs scheduled to record - and the computer just keeps running after I select yes, never going into standby. I added that detail as it shows the standby process is starting. [This problem also happens if a TV program is not scheduled, so the scheduler task in not running/in memory. This problem happens regardless of whether I'm not watching TV. This problem happens regardless of whether Media Center is running (it usually isn't, I'm using Pinnacle to watch TV).] I looked at "How to troubleshoot hibernation and standby issues in Windows XP" http://support.microsoft.com/kb/907477 - ACPI is enabled, and "standby" is an option in "Power Options Properties." So it appears to be setup correctly. Windows XP SP3 Media Center Edition, all current updates installed.

  Read the article

• Does Guest WiFi on an Access Point make any sense?

  - by uos??

  I have a Belkin WiFi Router which offers a feature of a secondary Guest Access WiFi network. Of course, the idea is that the Guest network doesn't have access to the computers/devices on the main network. I also have a Comcast-issues Cable Modem/Router device with mutliple wired ports, but no WiFi-capabilities. I prefer to only run one router/DHCP/NAT instead of both the Comcast Router and the Belkin Router, so I can disable the Routing functions of the Belkin and allow the Comcast Router to But if I disable the Routing functions of the Belkin device, the Guest WiFi network is still available. Is this configuration just as secure as when the Belkin acts as a Router? I guess the question comes down to this: Do Guest WiFi's provide security by 1) only allowing requests to IPs found in-front of the device, or do they work by 2) disallowing requests to IPs on the same subnet? 1) Would mean that Guest WiFi on an access point provides no benefit 2) Would mean that the Guest WiFi functionality can work even if the device is just an access point. Or maybe something else entirely?

  Read the article

• Windows server 2008R2 routing with single NIC

  - by Fabian

  I'm trying to duplicate a Linux server configuration to a windows server 2008R2 box. Basicaly this linux server acts as a router, but it is doing its job with only 1 interface (1 NIC). Here is the network configuration in place (I cannot change it) : INTERNET <== Router (local ip = 194.168.0.3) <== linux Server (ip : 194.168.0.2). The router is configured with a DMZ to 194.168.0.2, and only allow this IP to connect to internet (Cannot change this router configuration). The linux server is configured with a default gateway to 194.168.0.3, with the option : "Act as router". All other computer on the lan have this configuration (given by DHCP) : IP range : 194.168.0.X MASK : 255.255.255.0 Default gateway : 194.168.0.2 And everything is working perfectly. I'm trying to reproduce this way of routing with only one NIC from a windows server 2008R2, but it seems that you cannnot do it with only one NIC (all exemples I see are refering to 2 NIC with 2 different network). Does someone have an idea how to achieved this in Windows server 2008R2 ? Tx you for your help ! Fabian.

  Read the article

• Paste textbox from Powerpoint to Word as an editable control

  - by George Harris

  I have a Powerpoint 2007 file that contains a number of textboxes and shapes with text on them. I can edit, resize, change the text, etc. in these boxes in Powerpoint. However, if I select an item, copy it, and paste it into a Word 2007 document, I can't edit it. I can resize the entire thing, but it acts more like an image than a text box. I've tried the paste special options and keep source formatting options, but still can't edit it. Is there a way to be able to paste the editable content from Powerpoint and still have it editable in Word? Update I found this question that appears to get to the root of the problem: The MS Office Art graphics engine (aka Escher 2) is new to MS Office 2007 and while fully implemented in Excel and Powerpoint is only partially implemented in Word 2007 for backwards compatibility with the MS Office Drawing/Graphics engine (aka Escher) still available in Word It should work in earlier versions of Word and Word 2010, but not Word 2007. This is quite frustrating as I have to edit the slide in Powerpoint before copying it into Word. While doable, it adds another step, but the problem is that everyone who wants to update the Word document will have to do the same thing, adding complexity and steps for everyone. If I embed the Powerpoint slide in the document, I can edit the controls, but they don't scale the same way and takes a lot of work.

  Read the article

• Why am I unable to reach local network computers, but able to browse the web?

  - by Igor Zinov'yev

  I have a weird problem. Today after turning my Ubuntu 9.10 PC on I can't connect to my local network, but I can use the Internet. We have a single Windows 2003 server machine that acts as a local main DNS server, DHCP server and a domain controller. Although it seems to give me the local IP address, I can not ping it, as well as any other machine on the net. I have tried all of the below and it didn't help: Rebooting; Reconnecting to the network; Forcing the dhclient to renew the IP address; Deleting and creating new connection profiles; Plugging my machine into another network outlet; Maybe it has something to do with routing, because I have tampered with routing tables the day before, but the tables seem ok to me: $ route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.0.0 0.0.0.0 255.255.255.0 U 1 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 vboxnet0 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 Our LAN uses a D-Link DI-604 router, and it looks to me as if I am connected to the network outside the router. I can not even access its administration page. Please at least suggest what I can do to solve this. P.S. What seems strangest to me is that I can access the PC in question from outside the network by opening a port on the router. I have managed to ssh to it from outside, but I still can't ping nothing on the inside. P.P.S Today I tried reinstalling network-manager with --purge option, but it did no good. After that I created a new DCHP reservation for my PC in order to change my local IP, but that didn't change anything either. My PC is able to get a DHCP offer, but then it's unable to connect to any local computers. I am desperate.

  Read the article

• Test server on a local network with XAMPP

  - by hopscotch1978

  Hi, I'm not very proficient with networks and could use some help. I've got a Win 7 desktop with XAMPP which acts as my local dev machine. I've configured a virtual host on the desktop which I'm able to access fine. If I'm understanding things correctly, the virtual host uses port 80 (<VirtualHost 127.0.0.1:80>). I've just tried to configure a separate Win XP laptop on the local wireless network to connect to the main desktop for testing purposes. I've added the IP address and virtual host name to my Hosts file on the laptop. My virtual host is imaginatively named "virtualhost1". When I type this into my laptop browser, it connects correctly to the main desktop and I get the XAMPP welcome screen. But I can't seem to get to the actual site, just the XAMPP welcome screen. It kind of jumps the browser to http://virtualhost1/xampp/. I think it's a port issue of some sort but I have no idea how to resolve it. I would get the same XAMPP welcome screen on my desktop if I omitted ":80" from the virtual host declaration. On my main desktop, typing "virtualhost1" to the browser address bar gives me the site correctly, not the XAMPP welcome screen. Help would be appreciated. Thank you.

  Read the article

• Computer won't go into standby

  - by Robert

  When I select Start-Turn off computer-Standby the 'turn off computer' option window closes, and then nothing else happens. I can start new applications, and Windows acts like I never selected standby. I ran it for several hours after that. If I have a TV program scheduled to record when I select standby I get a window (the Pinnacle TV software) asking if I'm sure, there are programs scheduled to record - and the computer just keeps running after I select yes, never going into standby. I added that detail as it shows the standby process is starting. [This problem also happens if a TV program is not scheduled, so the scheduler task in not running/in memory. This problem happens regardless of whether I'm not watching TV. This problem happens regardless of whether Media Center is running (it usually isn't, I'm using Pinnacle to watch TV).] I looked at "How to troubleshoot hibernation and standby issues in Windows XP" http://support.microsoft.com/kb/907477 - ACPI is enabled, and "standby" is an option in "Power Options Properties." So it appears to be setup correctly. Windows XP SP3 Media Center Edition, all current updates installed.

  Read the article

• Cannot browse remote networks even with WINS configured

  - by paradroid

  As the NetBIOS protocol acts on Layer 2 and so is not routable, In order to enable network browsing of remote networks, WINS has been installed and configured on two domain controllers, both of which are on different networks. The WINS servers seem to be replicating with eachother, and each has 127.0.0.1 set as the Primary WINS Server in each of their LAN interface properties, with nothing entered for Secondary WINS Server. The DC which holds the PDC Emulator FSMO role has the Computer Browser service running and set to Auto start, and it has the WINS/NBT node type network setting at 0x8 (H-node - Hybrid node). Remote network browsing does not work. Is the WINS/NBT node type correct for this scenario? The reason why I think it may not be the right one is because I set the DHCP Server's 046 WINS/NBT node type option to 0x8 as well, after which the DHCP clients started to disappear from the Network folders. When that option is not set, does it default to B-node (Broadcast node)? Or could it be a problem with the WINS servers setup?

  Read the article

• Hardware issue: computer plays beep sounds at startup, and then turns off

  - by Darkkurama

  Turns out that after moving, my computer got damaged somehow. I installed my computer 2 days ago. I didn't check the state of the hardware parts and turned the pc on recklessly, not realizing that the cpu fan was dettached from the cpu. After this I reattached the fan. The computer worked kind of faulty after that, because at the time of startup, it would play a long beep (different from the normal beep) and won't display anything. I tried restarting after this incident and it got fixed (don't know how, but it did), and I was even able to play some videogames for some hours (more than 5). This morning I tried to get this issue sorted out by checking again the cpu and in general, the connections, and for my surprise, at the time of turning it on again, the computer wouldn't boot at all. I reapplied some thermal paste to the cpu and fan, but got no results (I did this because the old paste was very badly distributted along the surface of both cpu and fan). Now every time I turn it on, the computer acts randomly: sometimes at startup, it plays a long continous beep and then turns off. one time it played a long continous beep and got to the windows password input screen, but then it turned off More frequently, I turn it on and after some seconds, it turns off without any sound. You can check this video I recorded, which features how the computer behaves most of the time Another one I tried troubleshoting it myself by disconnecting my graphic card, rams, HDD and even the cpu and its fan with no result. Computer specs: Intel Core 2 Quad Q6600 processor, Nvidia xfx gtx 260 black edition, 4 GB ram, 500 GB hard drive, Windows 7 64 bit

  Read the article

• Windows server 2008R2 routing with single NIC

  - by Fabian

  I'm trying to duplicate a Linux server configuration to a windows server 2008R2 box. Basicaly this linux server acts as a router, but it is doing its job with only 1 interface (1 NIC). Here is the network configuration in place (I cannot change it) : INTERNET <== Router (local ip = 194.168.0.3) <== linux Server (ip : 194.168.0.2). The router is configured with a DMZ to 194.168.0.2, and only allow this IP to connect to internet (Cannot change this router configuration). The linux server is configured with a default gateway to 194.168.0.3, with the option : "Act as router". All other computer on the lan have this configuration (given by DHCP) : IP range : 194.168.0.X MASK : 255.255.255.0 Default gateway : 194.168.0.2 And everything is working perfectly. I'm trying to reproduce this way of routing with only one NIC from a windows server 2008R2, but it seems that you cannnot do it with only one NIC (all exemples I see are refering to 2 NIC with 2 different network). Does someone have an idea how to achieved this in Windows server 2008R2 ? Tx you for your help ! Fabian.

  Read the article

< Previous Page | 17 18 19 20 21 22 23 24 25 26 27 28  | Next Page >