garreth 00 - Page 21 - Developer IT

Slow wired internet connection on Realtek RTL8168-8111 (Rev 6)

- by Mark

I keep on seeing issues people are having with their wireless. I am having an issue with being wired into my router. I installed Ubuntu 11.10 the other day, on my custom PC. The motherboard I have installed on this PC is an ASUS P8H61-M. The issue I am having is with my speed. I have a dual boot, windows 7 and the new Ubuntu. On my Windows install I am getting test speeds from Speakeasy at 17Mbps and actual downloads around 2-3MB/s. With Ubuntu, I am getting test speeds from Speakeasy at 1.14Mbps and actual downloads around 60KB/s. I have disabled IPv6 and am no using GoogleDNS for my DNS, but it hasn't resolved the issue. I have scanned my router (WRT54GS Linksys) to disable IPv6 connections, and I am not seeing any option for that. I cannot figure out why I am getting such sluggish internet connection. Any help to resolve would be great! I performed an iconfig -a with these results: mark@Mark-ASUS:~$ ifconfig -a eth0 Link encap:Ethernet HWaddr f4:6d:04:d1:2c:4e inet addr:192.168.1.103 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::f66d:4ff:fed1:2c4e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:21888 errors:0 dropped:21888 overruns:0 frame:21888 TX packets:21068 errors:0 dropped:90 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:26348337 (26.3 MB) TX bytes:2217140 (2.2 MB) Interrupt:46 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:7 errors:0 dropped:0 overruns:0 frame:0 TX packets:7 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:952 (952.0 B) TX bytes:952 (952.0 B) My specs are: mark@Mark-ASUS:~$ sudo lspci -nn 04:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 06) 06:00.0 PCI bridge [0604]: ASMedia Technology Inc. Device [1b21:1080] (rev 01) udev information: KERNEL[11.351405] add /devices/pci0000:00/0000:00:1c.2/0000:04:00.0/net/eth0 (net) UDEV_LOG=3 ACTION=add DEVPATH=/devices/pci0000:00/0000:00:1c.2/0000:04:00.0/net/eth0 SUBSYSTEM=net INTERFACE=eth0 IFINDEX=2 SEQNUM=1542 UDEV [11.363905] add /devices/pci0000:00/0000:00:1c.2/0000:04:00.0/net/eth0 (net) UDEV_LOG=3 ACTION=add DEVPATH=/devices/pci0000:00/0000:00:1c.2/0000:04:00.0/net/eth0 SUBSYSTEM=net INTERFACE=eth0 IFINDEX=2 SEQNUM=1542 ID_VENDOR_FROM_DATABASE=Realtek Semiconductor Co., Ltd. ID_MODEL_FROM_DATABASE=RTL8111/8168B PCI Express Gigabit Ethernet controller ID_BUS=pci ID_VENDOR_ID=0x10ec ID_MODEL_ID=0x8168 ID_MM_CANDIDATE=1 dmesg information: [ 2.855982] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 2.856366] r8169 0000:04:00.0: eth0: RTL8168b/8111b at 0xffffc9000064c000, f4:6d:04:d1:2c:4e, XID 0c900800 IRQ 46 [ 12.540956] r8169 0000:04:00.0: eth0: link down [ 12.540961] r8169 0000:04:00.0: eth0: link down [ 12.541173] ADDRCONF(NETDEV_UP): eth0: link is not ready I took out a lot of information that did not pertain to eth0, because the previous edits wouldn't save. If I need any more information, let me know. I would love to get this resolved. The other issue I am noticing is sometimes my connection disconnects all together, for about a minute, then it reconnects.

Read the article

Errors when trying to compile the driver for the rtl8192su wireless adapter

- by Tom Brito

I have a wireless to usb adapter, and I'm having some trouble to install the drivers on Ubuntu. First of all, the readme says to use the make command, and I already got errors: $ make make[1]: Entering directory `/usr/src/linux-headers-2.6.35-22-generic' CC [M] /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.o /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c: In function ‘rtl8192_usb_probe’: /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12325: error: ‘struct net_device’ has no member named ‘open’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12326: error: ‘struct net_device’ has no member named ‘stop’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12327: error: ‘struct net_device’ has no member named ‘tx_timeout’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12328: error: ‘struct net_device’ has no member named ‘do_ioctl’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12329: error: ‘struct net_device’ has no member named ‘set_multicast_list’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12330: error: ‘struct net_device’ has no member named ‘set_mac_address’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12331: error: ‘struct net_device’ has no member named ‘get_stats’ /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.c:12332: error: ‘struct net_device’ has no member named ‘hard_start_xmit’ make[2]: *** [/home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u/r8192U_core.o] Error 1 make[1]: *** [_module_/home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/HAL/rtl8192u] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-2.6.35-22-generic' make: *** [all] Error 2 /home/wellington/Desktop/rtl8192su_linux_2.4_2.6.0003.0301.2010/ is the path where I copied the drivers on my computer. Any idea how to solve this? (I don't even know what the error is...) update: sudo lshw -class network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 03 serial: 78:e3:b5:e7:5f:6e size: 10MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10MB/s resources: irq:42 ioport:d800(size=256) memory:fbeff000-fbefffff memory:faffc000-faffffff memory:fbec0000-fbedffff *-network DISABLED description: Wireless interface physical id: 2 logical name: wlan0 serial: 00:26:18:a1:ae:64 capabilities: ethernet physical wireless configuration: broadcast=yes multicast=yes wireless=802.11b/g sudo lspci 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 18) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 18) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06) 00:1c.2 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 3 (rev 06) 00:1d.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev a6) 00:1f.0 ISA bridge: Intel Corporation 5 Series Chipset LPC Interface Controller (rev 06) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 6 port SATA AHCI Controller (rev 06) 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 06) 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) 02:00.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6315 Series Firewire Controller (rev 01) sudo lsusb Bus 002 Device 003: ID 0bda:0158 Realtek Semiconductor Corp. USB 2.0 multicard reader Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 004: ID 045e:00f9 Microsoft Corp. Wireless Desktop Receiver 3.1 Bus 001 Device 003: ID 0b05:1786 ASUSTek Computer, Inc. Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

Read the article

Can't start httpd 2.4.9 with self-signed SSL certificate

- by Smollet

I cannot start the httpd 2.4.9 (tried 2.4.x too) on CentOS 6.5 with the simplest SSL config possible. The openssl version installed on the machine is OpenSSL 1.0.1e-fips 11 Feb 2013 (I've upgraded it using 'yum update' to the latest patched version as well) I have compiled and installed the httpd 2.4.9 using the following commands: ./configure --enable-ssl --with-ssl=/usr/local/ssl/ --enable-proxy=shared --enable-proxy_wstunnel=shared --with-apr=apr-1.5.1/ --with-apr-util=apr-util-1.5.3/ make make install Now I'm generating the default self-signed certificate as described in the CentOS HowTo: openssl genrsa -out ca.key 2048 openssl req -new -key ca.key -out ca.csr openssl x509 -req -days 365 -in ca.csr -signkey ca.key -out ca.crt cp ca.crt /etc/pki/tls/certs cp ca.key /etc/pki/tls/private/ca.key cp ca.csr /etc/pki/tls/private/ca.csr Here is my httpd-ssl.conf file: Listen 443 SSLCipherSuite HIGH:MEDIUM:!aNULL:!MD5 SSLPassPhraseDialog builtin SSLSessionCache "shmcb:/usr/local/apache2/logs/ssl_scache(512000)" SSLSessionCacheTimeout 300 <VirtualHost *:443> SSLEngine on SSLCertificateFile /etc/pki/tls/certs/ca.crt SSLCertificateKeyFile /etc/pki/tls/private/ca.key <FilesMatch "\.(cgi|shtml|phtml|php)$"> SSLOptions +StdEnvVars </FilesMatch> <Directory "/usr/local/apache2/cgi-bin"> SSLOptions +StdEnvVars </Directory> BrowserMatch "MSIE [2-5]" \ nokeepalive ssl-unclean-shutdown \ downgrade-1.0 force-response-1.0 CustomLog "/usr/local/apache2/logs/ssl_request_log" \ "%t %h %{SSL_PROTOCOL}x %{SSL_CIPHER}x \"%r\" %b" </VirtualHost> when I start httpd using bin/apachectl -k start I get following errors in the error_log: Wed Jun 04 00:29:27.995654 2014] [ssl:info] [pid 24021:tid 139640404293376] AH01887: Init: Initializing (virtual) servers for SSL [Wed Jun 04 00:29:27.995726 2014] [ssl:info] [pid 24021:tid 139640404293376] AH01914: Configuring server 192.168.9.128:443 for SSL protocol [Wed Jun 04 00:29:27.995863 2014] [ssl:debug] [pid 24021:tid 139640404293376] ssl_engine_init.c(312): AH01893: Configuring TLS extension handling [Wed Jun 04 00:29:27.996111 2014] [ssl:debug] [pid 24021:tid 139640404293376] ssl_util_ssl.c(343): AH02412: [192.168.9.128:443] Cert matches for name '192.168.9.128' [subject: CN=192.168.9.128,OU=XXX,O=XXXX,L=XXXX,ST=NRW,C=DE / issuer: CN=192.168.9.128,OU=XXX,O=XXXX,L=XXXX,ST=NRW,C=DE / serial: AF04AF31799B7695 / notbefore: Jun 3 22:26:45 2014 GMT / notafter: Jun 3 22:26:45 2015 GMT] [Wed Jun 04 00:29:27.996122 2014] [ssl:info] [pid 24021:tid 139640404293376] AH02568: Certificate and private key 192.168.9.128:443:0 configured from /etc/pki/tls/certs/ca.crt and /etc/pki/tls/private/ca.key [Wed Jun 04 00:29:27.996209 2014] [ssl:info] [pid 24021:tid 139640404293376] AH01914: Configuring server 192.168.9.128:443 for SSL protocol [Wed Jun 04 00:29:27.996280 2014] [ssl:debug] [pid 24021:tid 139640404293376] ssl_engine_init.c(312): AH01893: Configuring TLS extension handling [Wed Jun 04 00:29:27.996295 2014] [ssl:emerg] [pid 24021:tid 139640404293376] AH02572: Failed to configure at least one certificate and key for 192.168.9.128:443 [Wed Jun 04 00:29:27.996303 2014] [ssl:emerg] [pid 24021:tid 139640404293376] SSL Library Error: error:0906D06C:PEM routines:PEM_read_bio:no start line (Expecting: DH PARAMETERS) -- Bad file contents or format - or even just a forgotten SSLCertificateKeyFile? [Wed Jun 04 00:29:27.996308 2014] [ssl:emerg] [pid 24021:tid 139640404293376] SSL Library Error: error:0906D06C:PEM routines:PEM_read_bio:no start line (Expecting: EC PARAMETERS) -- Bad file contents or format - or even just a forgotten SSLCertificateKeyFile? [Wed Jun 04 00:29:27.996318 2014] [ssl:emerg] [pid 24021:tid 139640404293376] SSL Library Error: error:140A80B1:SSL routines:SSL_CTX_check_private_key:no certificate assigned [Wed Jun 04 00:29:27.996321 2014] [ssl:emerg] [pid 24021:tid 139640404293376] AH02312: Fatal error initialising mod_ssl, exiting. AH00016: Configuration Failed I then try to generate missing DH PARAMETERS and EC PARAMETERS: openssl dhparam -outform PEM -out dhparam.pem 2048 openssl ecparam -out ec_param.pem -name prime256v1 cat dhparam.pem ec_param.pem >> /etc/pki/tls/certs/ca.crt And it mitigates the error but the next comes out: [Wed Jun 04 00:34:05.021438 2014] [ssl:info] [pid 24089:tid 140719371077376] AH01887: Init: Initializing (virtual) servers for SSL [Wed Jun 04 00:34:05.021487 2014] [ssl:info] [pid 24089:tid 140719371077376] AH01914: Configuring server 192.168.9.128:443 for SSL protocol [Wed Jun 04 00:34:05.021874 2014] [ssl:debug] [pid 24089:tid 140719371077376] ssl_engine_init.c(312): AH01893: Configuring TLS extension handling [Wed Jun 04 00:34:05.022050 2014] [ssl:debug] [pid 24089:tid 140719371077376] ssl_util_ssl.c(343): AH02412: [192.168.9.128:443] Cert matches for name '192.168.9.128' [subject: CN=192.168.9.128,OU=XXX,O=XXXX,L=XXXX,ST=NRW,C=DE / issuer: CN=192.168.9.128,OU=XXX,O=XXXX,L=XXXX,ST=NRW,C=DE / serial: AF04AF31799B7695 / notbefore: Jun 3 22:26:45 2014 GMT / notafter: Jun 3 22:26:45 2015 GMT] [Wed Jun 04 00:34:05.022066 2014] [ssl:info] [pid 24089:tid 140719371077376] AH02568: Certificate and private key 192.168.9.128:443:0 configured from /etc/pki/tls/certs/ca.crt and /etc/pki/tls/private/ca.key [Wed Jun 04 00:34:05.022285 2014] [ssl:debug] [pid 24089:tid 140719371077376] ssl_engine_init.c(1016): AH02540: Custom DH parameters (2048 bits) for 192.168.9.128:443 loaded from /etc/pki/tls/certs/ca.crt [Wed Jun 04 00:34:05.022389 2014] [ssl:debug] [pid 24089:tid 140719371077376] ssl_engine_init.c(1030): AH02541: ECDH curve prime256v1 for 192.168.9.128:443 specified in /etc/pki/tls/certs/ca.crt [Wed Jun 04 00:34:05.022397 2014] [ssl:info] [pid 24089:tid 140719371077376] AH01914: Configuring server 192.168.9.128:443 for SSL protocol [Wed Jun 04 00:34:05.022464 2014] [ssl:debug] [pid 24089:tid 140719371077376] ssl_engine_init.c(312): AH01893: Configuring TLS extension handling [Wed Jun 04 00:34:05.022478 2014] [ssl:emerg] [pid 24089:tid 140719371077376] AH02572: Failed to configure at least one certificate and key for 192.168.9.128:443 [Wed Jun 04 00:34:05.022488 2014] [ssl:emerg] [pid 24089:tid 140719371077376] SSL Library Error: error:140A80B1:SSL routines:SSL_CTX_check_private_key:no certificate assigned [Wed Jun 04 00:34:05.022491 2014] [ssl:emerg] [pid 24089:tid 140719371077376] AH02312: Fatal error initialising mod_ssl, exiting. AH00016: Configuration Failed I have tried to generate the simple certificate/key pair exactly as described in the httpd docs Unfortunately, I still get exact same errors as above. I've seen a bug report with the similar issue: https://issues.apache.org/bugzilla/show_bug.cgi?id=56410 But the openssl version I have is reported as working there. I've also tried to apply the patch from the report as well as build the latest 2.4.x branch with no success, I get the same errors as above. I have also tried to create a short chain of certificates and set the root CA certificate using SSLCertificateChainFile directive. That didn't help either, I get exact same errors as above. I'm not interested in setting up hardened security, etc. The only thing I need is to start httpd with the simplest SSL config possible to continue testing proxy config for the mod_proxy_wstunnel Had anybody encountered and solved this issue? Is my sequence for creating a self-signed certificate incorrect? I'd appreciate any help very much!

Read the article

emacs, colors in term-mode

- by valya

Hello, I use Emacs and I run bash with M-x term command. There is a problem: colors in the *terminal* buffer aren't the same as in Gnome Terminal, and they are worse (do you need a screen shot?). How can I fix this? This is pretty annoying :-) Thank you! Linux Mint 9 Emacs 23.1.1 x86_64 __________________ /home/valentin/Work/buzzoola/buzzoola/test/vagrant [.../vagrant]$ echo $TERM eterm-color __________________ /home/valentin/Work/buzzoola/buzzoola/test/vagrant [.../vagrant]$ echo $LS_COLORS rs=0:di=01;34:ln=01;36:hl=44;37:pi=40;33:so=01;35:do=01;35:bd=40;33;01:cd=40;33;01:or=40;31 ;01:su=37;41:sg=30;43:ca=30;41:tw=30;42:ow=34;42:st=37;44:ex=01;32:*.tar=01;31:*.tgz=01;31: *.arj=01;31:*.taz=01;31:*.lzh=01;31:*.lzma=01;31:*.zip=01;31:*.z=01;31:*.Z=01;31:*.dz=01;31 :*.gz=01;31:*.bz2=01;31:*.bz=01;31:*.tbz2=01;31:*.tz=01;31:*.deb=01;31:*.rpm=01;31:*.jar=01 ;31:*.rar=01;31:*.ace=01;31:*.zoo=01;31:*.cpio=01;31:*.7z=01;31:*.rz=01;31:*.jpg=01;35:*.jp eg=01;35:*.gif=01;35:*.bmp=01;35:*.pbm=01;35:*.pgm=01;35:*.ppm=01;35:*.tga=01;35:*.xbm=01;3 5:*.xpm=01;35:*.tif=01;35:*.tiff=01;35:*.png=01;35:*.svg=01;35:*.svgz=01;35:*.mng=01;35:*.p cx=01;35:*.mov=01;35:*.mpg=01;35:*.mpeg=01;35:*.m2v=01;35:*.mkv=01;35:*.ogm=01;35:*.mp4=01; 35:*.m4v=01;35:*.mp4v=01;35:*.vob=01;35:*.qt=01;35:*.nuv=01;35:*.wmv=01;35:*.asf=01;35:*.rm =01;35:*.rmvb=01;35:*.flc=01;35:*.avi=01;35:*.fli=01;35:*.flv=01;35:*.gl=01;35:*.dl=01;35:* .xcf=01;35:*.xwd=01;35:*.yuv=01;35:*.axv=01;35:*.anx=01;35:*.ogv=01;35:*.ogx=01;35:*.aac=00 ;36:*.au=00;36:*.flac=00;36:*.mid=00;36:*.midi=00;36:*.mka=00;36:*.mp3=00;36:*.mpc=00;36:*. ogg=00;36:*.ra=00;36:*.wav=00;36:*.axa=00;36:*.oga=00;36:*.spx=00;36:*.xspf=00;36:

Read the article

How to revert AIX service pack?

- by unknown (google)

I have an AIX 6.1 box with service pack level 6100-02-03-0909 swax23 # oslevel -s -q Known Service Packs 6100-02-03-0909 6100-02-02-0849 6100-02-01-0847 6100-02-00-0000 6100-01-04-0909 6100-01-03-0846 6100-01-02-0834 6100-01-01-0823 6100-00-08-0909 6100-00-07-0846 6100-00-06-0834 6100-00-05-0822 6100-00-04-0815 6100-00-03-0808 6100-00-02-0750 6100-00-01-0748 I want to revert the latest serive pack and go back to 6100-02-02-0849. How to do it?

Read the article

The previous system shutdown at xxxx was unexpected

- by m.edmondson

For the past two nights we had a remote server shutdown unexpectedly. When rebooted we get the following message: Event Type: Error Event Source: EventLog Event Category: None Event ID: 6008 Date: 16/02/2011 Time: 09:10:43 User: N/A Computer: WELPLAN-1 Description: The previous system shutdown at 07:27:32 on 16/02/2011 was unexpected. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: db 07 02 00 03 00 10 00 Û....... 0008: 07 00 1b 00 20 00 42 02 .... .B. 0010: db 07 02 00 03 00 10 00 Û....... 0018: 07 00 1b 00 20 00 42 02 .... .B. Obviously this message doesn't help much, but what does all the hexadecimal mean? Will it help me track down the problem? Any pointers as to where to look?

Read the article

Why do ICMP Redirct Host happen?

- by El Barto

I'm setting up a Debian box as a router for 4 subnets. For that I have defined 4 virtual interfaces on the NIC where the LAN is connected (eth1). eth1 Link encap:Ethernet HWaddr 94:0c:6d:82:0d:98 inet addr:10.1.1.1 Bcast:10.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::960c:6dff:fe82:d98/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:6026521 errors:0 dropped:0 overruns:0 frame:0 TX packets:35331299 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:673201397 (642.0 MiB) TX bytes:177276932 (169.0 MiB) Interrupt:19 Base address:0x6000 eth1:0 Link encap:Ethernet HWaddr 94:0c:6d:82:0d:98 inet addr:10.1.2.1 Bcast:10.1.2.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:19 Base address:0x6000 eth1:1 Link encap:Ethernet HWaddr 94:0c:6d:82:0d:98 inet addr:10.1.3.1 Bcast:10.1.3.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:19 Base address:0x6000 eth1:2 Link encap:Ethernet HWaddr 94:0c:6d:82:0d:98 inet addr:10.1.4.1 Bcast:10.1.4.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:19 Base address:0x6000 eth2 Link encap:Ethernet HWaddr 6c:f0:49:a4:47:38 inet addr:192.168.1.10 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::6ef0:49ff:fea4:4738/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:199809345 errors:0 dropped:0 overruns:0 frame:0 TX packets:158362936 errors:0 dropped:0 overruns:0 carrier:1 collisions:0 txqueuelen:1000 RX bytes:3656983762 (3.4 GiB) TX bytes:1715848473 (1.5 GiB) Interrupt:27 eth3 Link encap:Ethernet HWaddr 94:0c:6d:82:c8:72 inet addr:192.168.2.5 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::960c:6dff:fe82:c872/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:110814 errors:0 dropped:0 overruns:0 frame:0 TX packets:73386 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:16044901 (15.3 MiB) TX bytes:42125647 (40.1 MiB) Interrupt:20 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:22351 errors:0 dropped:0 overruns:0 frame:0 TX packets:22351 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2625143 (2.5 MiB) TX bytes:2625143 (2.5 MiB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.8.0.1 P-t-P:10.8.0.2 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:41358924 errors:0 dropped:0 overruns:0 frame:0 TX packets:23116350 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:3065505744 (2.8 GiB) TX bytes:1324358330 (1.2 GiB) I have two other computers connected to this network. One has IP 10.1.1.12 (subnet mask 255.255.255.0) and the other one 10.1.2.20 (subnet mask 255.255.255.0). I want to be able to reach 10.1.1.12 from 10.1.2.20. Since packet forwarding is enabled in the router and the policy of the FORWARD chain is ACCEPT (and there are no other rules), I understand that there should be no problem to ping from 10.1.2.20 to 10.1.1.12 going through the router. However, this is what I get: $ ping -c15 10.1.1.12 PING 10.1.1.12 (10.1.1.12): 56 data bytes Request timeout for icmp_seq 0 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 81d4 0 0000 3f 01 e2b3 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 1 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 899b 0 0000 3f 01 daec 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 2 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 78fe 0 0000 3f 01 eb89 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 3 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 14b8 0 0000 3f 01 4fd0 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 4 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 8ef7 0 0000 3f 01 d590 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 5 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 ec9d 0 0000 3f 01 77ea 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 6 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 70e6 0 0000 3f 01 f3a1 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 7 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 b0d2 0 0000 3f 01 b3b5 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 8 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 f8b4 0 0000 3f 01 6bd3 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 9 Request timeout for icmp_seq 10 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 1c95 0 0000 3f 01 47f3 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 11 Request timeout for icmp_seq 12 Request timeout for icmp_seq 13 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 62bc 0 0000 3f 01 01cc 10.1.2.20 10.1.1.12 Why does this happen? From what I've read the Redirect Host response has something to do with the fact that the two hosts are in the same network and there being a shorter route (or so I understood). They are in fact in the same physical network, but why would there be a better route if they are not on the same subnet (they can't see each other)? What am I missing? Some extra info you might want to see: # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.8.0.2 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 127.0.0.1 0.0.0.0 255.255.255.255 UH 0 0 0 lo 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth3 10.8.0.0 10.8.0.2 255.255.255.0 UG 0 0 0 tun0 192.168.1.0 0.0.0.0 255.255.255.0 U 1 0 0 eth2 10.1.4.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 10.1.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 10.1.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 10.1.3.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth2 0.0.0.0 192.168.2.1 0.0.0.0 UG 100 0 0 eth3 # iptables -L -n Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination # iptables -L -n -t nat Chain PREROUTING (policy ACCEPT) target prot opt source destination Chain POSTROUTING (policy ACCEPT) target prot opt source destination MASQUERADE all -- !10.0.0.0/8 10.0.0.0/8 MASQUERADE all -- 10.0.0.0/8 !10.0.0.0/8 Chain OUTPUT (policy ACCEPT) target prot opt source destination

Read the article

Ubuntu Server 12.04 CPU Load

- by zertux

I have a Server (2x Hexa-Core Xeon E5649 2.53GHz w/HT with 32GB RAM and 20000 GB Bandwidth) running Ubuntu Server 12.04 LTS. The server runs LAMP and serves one website only, the estimated number of users is to be ~ 15,000 at the same time. At the moment i have around 2000 users online each of them runs 50 MySQL queries (small values mostly select and insert) from the beginning until the end of the session. Server CPU Load is high at this number of connections while the RAM usage is almost 1GB out of 32GB its worth mentioning that the server was running very fast with no problems at all but am concerned about the load average. http://s12.postimage.org/z7hi6mz3h/photo.png top - 03:02:43 up 9 min, 2 users, load average: 50.83, 30.14, 12.83 Tasks: 432 total, 1 running, 430 sleeping, 0 stopped, 1 zombie Cpu(s): 0.1%us, 0.2%sy, 0.0%ni, 66.5%id, 33.1%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 32939992k total, 3111604k used, 29828388k free, 84108k buffers Swap: 2048280k total, 0k used, 2048280k free, 1621640k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 2860 root 20 0 25820 2288 1420 S 3 0.0 0:11.18 htop 1182 root 20 0 0 0 0 D 2 0.0 0:01.46 kjournald 1935 mysql 20 0 12.3g 161m 7924 S 1 0.5 102:31.45 mysqld 11 root 20 0 0 0 0 S 0 0.0 0:00.38 kworker/0:1 1822 www-data 20 0 247m 25m 4188 D 0 0.1 0:01.81 apache2 2920 www-data 20 0 0 0 0 Z 0 0.0 0:01.20 apache2 <defunct> 2942 www-data 20 0 247m 23m 3056 D 0 0.1 0:00.20 apache2 3516 www-data 20 0 247m 23m 3028 D 0 0.1 0:00.06 apache2 3521 www-data 20 0 247m 23m 3020 D 0 0.1 0:00.09 apache2 3664 www-data 20 0 247m 23m 3132 D 0 0.1 0:00.09 apache2 3674 www-data 20 0 247m 23m 3252 D 0 0.1 0:00.06 apache2 3713 www-data 20 0 247m 23m 3040 D 0 0.1 0:00.09 apache2 1 root 20 0 24328 2284 1344 S 0 0.0 0:03.09 init 2 root 20 0 0 0 0 S 0 0.0 0:00.00 kthreadd 3 root 20 0 0 0 0 S 0 0.0 0:00.01 ksoftirqd/0 6 root RT 0 0 0 0 S 0 0.0 0:00.00 migration/0 7 root RT 0 0 0 0 S 0 0.0 0:00.00 watchdog/0 8 root RT 0 0 0 0 S 0 0.0 0:00.00 migration/1 9 root 20 0 0 0 0 S 0 0.0 0:00.00 kworker/1:0 root@server:~/codes# vmstat 1 procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 19 0 0 29684012 86112 1689844 0 0 19 590 254 231 48 0 47 5 23 0 0 29704812 86128 1697672 0 0 4 320 11100 8121 77 1 22 0 33 0 0 29671044 86156 1705308 0 0 0 5440 13190 9140 95 1 4 0 33 3 0 29670088 86160 1706288 0 0 0 32932 12275 7297 99 0 1 0 35 0 0 29693456 86188 1710724 0 0 4 676 12701 7867 98 1 1 0 ^C I have not changed any of the default configurations that comes with Ubuntu. Is this load normal for such powerful server ? is there any optimization i can make to Apache/MySQL to minimize the load ? What do you recommend ?

Read the article

Exchange Server 2007 message tracking log tuning ?

- by Albert Widjaja

Hi All, what is the best practice if I want to have a retention of let say 6 months ? I'm confused which parameter that is should/can be changes. Get-ExchangeServer | where {$_.isHubTransportServer -eq $true} | Get-TransportServer | select Name, *MessageTracking* | ft -AutoSize Name MessageTrackingLogEnabled MessageTrackingLogMaxAge MessageTrackingLogMaxDirectorySize MessageTrackingLogMaxFileSize MessageTrackingLogPat h ---- ------------------------- ------------------------ ---------------------------------- ----------------------------- --------------------- ExHTServer1 True 20.00:00:00 250MB 10MB D:\Program Files\M... ExHTServer2 True 20.00:00:00 250MB 10MB D:\Program Files\M... ExHTServer3 True 20.00:00:00 250MB 10MB D:\Program Files\M... Thanks, Albert

Read the article

Why do ICMP Redirect Host happen?

- by El Barto

I'm setting up a Debian box as a router for 4 subnets. For that I have defined 4 virtual interfaces on the NIC where the LAN is connected (eth1). eth1 Link encap:Ethernet HWaddr 94:0c:6d:82:0d:98 inet addr:10.1.1.1 Bcast:10.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::960c:6dff:fe82:d98/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:6026521 errors:0 dropped:0 overruns:0 frame:0 TX packets:35331299 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:673201397 (642.0 MiB) TX bytes:177276932 (169.0 MiB) Interrupt:19 Base address:0x6000 eth1:0 Link encap:Ethernet HWaddr 94:0c:6d:82:0d:98 inet addr:10.1.2.1 Bcast:10.1.2.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:19 Base address:0x6000 eth1:1 Link encap:Ethernet HWaddr 94:0c:6d:82:0d:98 inet addr:10.1.3.1 Bcast:10.1.3.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:19 Base address:0x6000 eth1:2 Link encap:Ethernet HWaddr 94:0c:6d:82:0d:98 inet addr:10.1.4.1 Bcast:10.1.4.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:19 Base address:0x6000 eth2 Link encap:Ethernet HWaddr 6c:f0:49:a4:47:38 inet addr:192.168.1.10 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::6ef0:49ff:fea4:4738/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:199809345 errors:0 dropped:0 overruns:0 frame:0 TX packets:158362936 errors:0 dropped:0 overruns:0 carrier:1 collisions:0 txqueuelen:1000 RX bytes:3656983762 (3.4 GiB) TX bytes:1715848473 (1.5 GiB) Interrupt:27 eth3 Link encap:Ethernet HWaddr 94:0c:6d:82:c8:72 inet addr:192.168.2.5 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::960c:6dff:fe82:c872/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:110814 errors:0 dropped:0 overruns:0 frame:0 TX packets:73386 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:16044901 (15.3 MiB) TX bytes:42125647 (40.1 MiB) Interrupt:20 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:22351 errors:0 dropped:0 overruns:0 frame:0 TX packets:22351 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2625143 (2.5 MiB) TX bytes:2625143 (2.5 MiB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.8.0.1 P-t-P:10.8.0.2 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:41358924 errors:0 dropped:0 overruns:0 frame:0 TX packets:23116350 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:3065505744 (2.8 GiB) TX bytes:1324358330 (1.2 GiB) I have two other computers connected to this network. One has IP 10.1.1.12 (subnet mask 255.255.255.0) and the other one 10.1.2.20 (subnet mask 255.255.255.0). I want to be able to reach 10.1.1.12 from 10.1.2.20. Since packet forwarding is enabled in the router and the policy of the FORWARD chain is ACCEPT (and there are no other rules), I understand that there should be no problem to ping from 10.1.2.20 to 10.1.1.12 going through the router. However, this is what I get: $ ping -c15 10.1.1.12 PING 10.1.1.12 (10.1.1.12): 56 data bytes Request timeout for icmp_seq 0 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 81d4 0 0000 3f 01 e2b3 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 1 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 899b 0 0000 3f 01 daec 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 2 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 78fe 0 0000 3f 01 eb89 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 3 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 14b8 0 0000 3f 01 4fd0 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 4 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 8ef7 0 0000 3f 01 d590 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 5 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 ec9d 0 0000 3f 01 77ea 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 6 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 70e6 0 0000 3f 01 f3a1 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 7 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 b0d2 0 0000 3f 01 b3b5 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 8 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 f8b4 0 0000 3f 01 6bd3 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 9 Request timeout for icmp_seq 10 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 1c95 0 0000 3f 01 47f3 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 11 Request timeout for icmp_seq 12 Request timeout for icmp_seq 13 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 62bc 0 0000 3f 01 01cc 10.1.2.20 10.1.1.12 Why does this happen? From what I've read the Redirect Host response has something to do with the fact that the two hosts are in the same network and there being a shorter route (or so I understood). They are in fact in the same physical network, but why would there be a better route if they are not on the same subnet (they can't see each other)? What am I missing? Some extra info you might want to see: # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.8.0.2 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 127.0.0.1 0.0.0.0 255.255.255.255 UH 0 0 0 lo 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth3 10.8.0.0 10.8.0.2 255.255.255.0 UG 0 0 0 tun0 192.168.1.0 0.0.0.0 255.255.255.0 U 1 0 0 eth2 10.1.4.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 10.1.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 10.1.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 10.1.3.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth2 0.0.0.0 192.168.2.1 0.0.0.0 UG 100 0 0 eth3 # iptables -L -n Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination # iptables -L -n -t nat Chain PREROUTING (policy ACCEPT) target prot opt source destination Chain POSTROUTING (policy ACCEPT) target prot opt source destination MASQUERADE all -- !10.0.0.0/8 10.0.0.0/8 MASQUERADE all -- 10.0.0.0/8 !10.0.0.0/8 Chain OUTPUT (policy ACCEPT) target prot opt source destination

Read the article

Backtrack, Wi-Fi not working

- by hradecek

I've installed Backtrack 5R3 KDE, and I realized that my wireless is not working, but wired is working fine. Here's the lshw output: *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 05 serial: 04:7d:7b:b7:46:f8 size: 100MB/s capacity: 100MB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8105e-1.fw ip=192.168.2.2 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:42 ioport:2000(size=256) memory:f0404000-f0404fff memory:f0400000-f0403fff lspci output: 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:14.0 USB Controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB Controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.1 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 2 (rev c4) 00:1d.0 USB Controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Panther Point 6 port SATA AHCI Controller (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 05)

Read the article

Timeperiod Setting

- by Alvin G. Matunog

I am running Nagios 3.2.3 on CentOS 5.7 32bit and I have a bit of a problem scheduling timeperiods. Please help me. Objective, to stop monitoring during server restart (since the server will be restarted and will be restarted automatically because of updates and system backup). The restart is scheduled every 1st Sunday of every month. My monitoring runs 24x7 but during restarts I want to stop the monitoring and resume after 30 mins. So every 1st Sunday I want my schedule to be 00:00-11:30,12:00-24:00. This means that it will stop at 11:30 and resumes on 12:00nn. If I set this on every Sunday there is no problem. But if I set this time on every 1st Sundays, it stops at 11:30 but resumes on the next day (Monday) and not on 12:00nn Sunday. I don't know what I am missing. If I set on regular weekdays there is no problem. But on Offset weekdays (1st Sunday) it doesn`t work the way it should have. Here is my definition; define timeperiod{ name 1st_sunday timeperiod_name 1st_sunday alias No monitoring every 1st Sunday thursday 1 00:00-11:30,12:00-24:00 } define timeperiod{ timeperiod_name irregular alias regular checking use 1st_sunday sunday 08:30-22:00 monday 08:30-22:00 tuesday 08:30-22:00 wednesday 08:30-22:00 thursday 08:30-19:10,19:20-22:00 friday 08:30-22:00 saturday 08:30-22:00 } Can anyone help me? Please? Thank you.

Read the article

udev rule not being executed

- by jyavenard

I have the following device that udevadm lists as: looking at device '/devices/pci0000:00/0000:00:1c.7/0000:09:00.0/usb6/6-2/6-2:1.0/ttyUSB0/tty/ttyUSB0': KERNEL=="ttyUSB0" SUBSYSTEM=="tty" DRIVER=="" looking at parent device '/devices/pci0000:00/0000:00:1c.7/0000:09:00.0/usb6/6-2/6-2:1.0/ttyUSB0': KERNELS=="ttyUSB0" SUBSYSTEMS=="usb-serial" DRIVERS=="pl2303" ATTRS{port_number}=="0" looking at parent device '/devices/pci0000:00/0000:00:1c.7/0000:09:00.0/usb6/6-2/6-2:1.0': KERNELS=="6-2:1.0" SUBSYSTEMS=="usb" DRIVERS=="pl2303" ATTRS{bInterfaceNumber}=="00" ATTRS{bAlternateSetting}==" 0" ATTRS{bNumEndpoints}=="03" ATTRS{bInterfaceClass}=="ff" ATTRS{bInterfaceSubClass}=="00" ATTRS{bInterfaceProtocol}=="00" ATTRS{supports_autosuspend}=="1" So I created the rule: KERNEL=="ttyUSB0", SUBSYSTEM=="tty", SUBSYSTEMS=="usb-serial", DRIVERS=="pl2303", KERNELS=="6-2:1.0", SYMLINK+="cc128serial" this doesn't work. However if I do: KERNEL=="ttyUSB0", SUBSYSTEM=="tty", SUBSYSTEMS=="usb-serial", DRIVERS=="pl2303", SYMLINK+="cc128serial" then it works. I tried with KERNELS=="6*" etc.. to no available any ideas ? thanks

Read the article

ksoftirqd uses 100% cpu

- by andy

I am running 32bit Ubuntu 10.04. A lot of the times ksoftirqd/0 or ksoftirqd/1 start using up 100% CPU for no apparent reason, and I am forced to reboot my laptop. Incidentally this also happens when I maximize my (youtube) videos on Chrome and Fireox, but once I un-maximize the videos the CPU usage goes down to the original levels. Any ideas what it going on? --- Addendum --- dmesg produces a ~2000 line output. I searched for 'error' and 'warning' in the output, and here are the relevant lines (along with some headers): [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 2.6.32-21-generic (buildd@yellow) (gcc version 4.4.3 (Ubuntu 4.4.3-4ubuntu5) ) #32-Ubuntu SMP Fri Apr 16 08:09:38 UTC 2010 (Ubuntu 2.6.32-21.32-generic 2.6.32.11+drm33.2) [ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32-21-generic root=UUID=157dcfda-acd6-4d1b-a6a8-ff9ccff61906 ro quiet splash [ 0.000000] KERNEL supported cpus: [ 0.000000] Intel GenuineIntel [ 0.000000] AMD AuthenticAMD [ 0.000000] Centaur CentaurHauls [ 0.000000] BIOS-provided physical RAM map: [ 24.775546] EXT3-fs warning: mounting fs with errors, running e2fsck is recommended [44920.210518] ata1: SError: { PHYRdyChg CommWake 10B8B Dispar LinkSeq TrStaTrns } [44920.210531] res 40/00:00:f0:4b:7f/00:00:18:00:00/40 Emask 0x10 (ATA bus error) [58673.134623] chrome[20101]: segfault at 7f38bc4ad000 ip 00007f38be769ecc sp 00007fff24616850 error 4 in libpepflashplayer.so[7f38bdc08000+e55000] [ 24.775546] EXT3-fs warning: mounting fs with errors, running e2fsck is recommended [44920.210531] res 40/00:00:f0:4b:7f/00:00:18:00:00/40 Emask 0x10 (ATA bus error)

Read the article

USB flash module giving errors

- by vshenoy

Hi, I have a SATA USB flash module which was earlier running a 2.4 linux kernel (2.4.36.6) and on which now I am trying to install ubuntu server 10.04.1 LTS. I have two such USB flash modules and on one of them the installation process itself giving these errors: sd 4:0:0:0 [sda] Device not ready sd 4:0:0:0 [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE sd 4:0:0:0 [sda] Sense Key : Not Ready [current] sd 4:0:0:0 [sda] Add. Sense: Medium not present sd 4:0:0:0 [sda] CDB: Write(10): 2a 00 00 05 48 02 00 00 04 00 end_request: I/O error, dev sda, sector 46114 usb 1-1: reset high speed USB device using ehci_hcd and address 2 Buffer I/O error on device sda1, logical block 172033 lost page write due to I/O error on sda1 Buffer I/O error on device sda1, logical block 172034 lost page write due to I/O error on sda1 on the other the installation is successful, but after a day or two of running the machine hangs because of kernel spewing these messages: Remounting filesystem read-only EXT2-fs error (device sda1): read_block_bitmap: Cannot read block [bitmap - block_group = 105, block_bitmap = 860161] EXT2-fs error (device sda1): ext2_get_inode: unable to read inode block - inode=13083, block=24683 ext2_free_inode: bit already cleared for inode 83966 and the machine needs to be hard rebooted. On both the systems SCSI emulation with usb_storage driver is being used to detect the module. Here is the output of /proc/scsi/scsi on 2.4: # cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 00 Lun: 00 Vendor: TS Model: UFM Rev: 1100 Type: Direct-Access ANSI SCSI revision: 02 and on 2.6: # cat /proc/scsi/scsi Attached devices: Host: scsi6 Channel: 00 Id: 00 Lun: 00 Vendor: TS Model: UFM Rev: 1100 Type: Direct-Access ANSI SCSI revision: 00 i.e. only 'ANSI SCSI revision:' is shown as different, although I am not sure if this can cause any problem. Really appreciate if someone can point as to how to debug this issue or any mailing list where I can further ask questions about this.

Read the article

Why execution of a portion of code loaded from external file is not halted by the OS?

- by menjaraz

I've harnessed a project released on internet a long time ago. Here comes the details, all irrelevant things being stripped off for sake of concision and clarity. A binary file whose content is descibed below HEX DUMP: 55 89 E5 83 EC 08 C7 45 FC 00 00 00 00 8B 45 FC 3B 45 10 72 02 EB 19 8B 45 FC 8B 55 0C 01 C2 8B 45 FC 03 45 08 8A 00 88 02 8D 45 FC FF 00 EB DD C6 45 FA 00 83 7D 10 01 76 6C 80 7D FA 00 74 02 EB 64 C6 45 FA 01 C7 45 FC 00 00 00 00 8B 45 10 48 39 45 FC 72 02 EB E2 8B 45 FC 8B 4D 0C 01 C1 8B 45 FC 03 45 0C 8D 50 01 8A 01 3A 02 73 30 8B 45 FC 03 45 0C 8A 00 88 45 FB 8B 45 FC 8B 55 0C 01 C2 8B 45 FC 03 45 0C 40 8A 00 88 02 8B 45 FC 03 45 0C 8D 50 01 8A 45 FB 88 02 C6 45 FA 00 8D 45 FC FF 00 EB A7 C9 C2 0C 00 90 90 90 90 90 90 is loaded into memory and executed using the following method snippet var MySrcArray, MyDestArray: array [1 .. 15] of Byte; // ... MyBuffer: Pointer; TheProc: procedure; SortIt: procedure(ASrc, ADest: Pointer; ASize: LongWord); stdcall; begin // Initialization of MySrcArray with random Bytes and display here ... // Instructions of loading of the binary file into MyBuffer using merely **GetMem** here ... @SortIt := MyBuffer; try SortIt(@MySrcArray, @MyDestArray, 15); // Display of MyDestArray (The outcome of the processing !) except // Invalid code error handling end; // Cleaning code here ... end; works like a charm on my box. My Question: How comes it works without using VirtualAlloc and/or VirtualProtect?

Read the article

Formatting a date string when the string sits inside another string

- by sf

Hi, I'm trying to figure out a way to format a date string that sits inside string using javascript. The string can be: "hello there From 2010-03-04 00:00:00.0 to 2010-03-31 00:00:00.0" or "stuff like 2010-03-04 20:00:00.0 and 2010-03-31 00:00:02.0 blah blah" I'd like it to end up like: "stuff like 4 March 2010 and 31 March 2010 blah blah" Does anyone have any idea as to how this could be achieved?

Read the article

Is it possible to read Fortran formatted data in Python?

- by Werner

I get output files from very old Fortran programs, which look like: 0.81667E+00 -0.12650E+01 -0.69389E-03 0.94381E+00 -0.11985E+01 -0.11502E+00 0.96064E+00 -0.11333E+01 -0.17616E+00 0.10202E+01 -0.12435E+01 -0.93917E-01 0.10026E+01 -0.10904E+01 -0.15108E+00 0.90516E+00 -0.11030E+01 -0.19139E+00 0.98624E+00 -0.11598E+01 -0.22970E+00 Is it possible to read this in Python and convert the numbers to "normal" floats?

Read the article

Why am I getting a "network is unreachable" error on Ubuntu Server?

- by jason328

I'm a completely new to Ubuntu server and am having a hard time connecting the server to the internet. I first ran ping -n 8.8.8.8 connect:Network is unreachable Then I ran ifconfig Link encap:Local Loopback inet addr:127.0.0.1 Mask 255.0.0.0 inet6 addr: ::1/28Scope:host UP LOOPBACK RUNNING MTU:16436 RX packets:192 errors:0 dropped:0 overruns:0 frame:0 TX packets:192 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:15360 (15.2KB) TX bytes:15360 (15.3KB) Here is ouput for sudo lspci -n 00:00.0 0600: 8086:2580 (rev 04) 00:02.0 0300: 8086:2582 (rev 04) 00:1d.0 0c03: 8086:2658 (rev 03) 00:1d.1 0c03: 8086:2659 (rev 03) 00:1d.0 0c03: 8086:265a (rev 03) 00:1d.0 0c03: 8086:265b (rev 03) 00:1d.0 0c03: 8086:265c (rev 03) 00:1e.0 0604: 8086:244e (rev d3) 00:1e.0 0401: 8086:266e (rev 03) 00:1f.0 0601: 8086:2640 (rev 03) 00:1f.0 0101: 8086:2651 (rev 03) 00:1f.0 0c05: 8086:266a (rev 03) 00:0b.0 0200: 8086:1654 (rev 03) lshw-c network returns WARNING: you should run this program as super-user. *-network DISABLED description:Ethernet interface product: NetXtreme BCM5705_2 Gigabit Ethernet vender: Broadcom Corporation physical id:b bus info:pci@0000:0a:0b.0 logical name: eth0 capabilities: bus_master_cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion= 3.121 firmware=5705-v3.18 latency=32 mingnt=64 multicast=yes port=twister pair lsmod code returned this Module Size Used By e100 37213 0 dm_crypt 23125 1 ppdev 17113 0 psmouse 87603 0 snd_intel8x0 38570 0 snd_ac97_codec 134826 1 snd_intel8x0 ac97_bus 12730 1 snd_ac97_codec snd_pcm 97188 2 snd_intel8x0, snd_ac97_codec serio_raw 13211 0 snd_timer 29990 1 snd_pcm snd 78855 4 snd_intel8x0, snd_ac97_codec, snd_pcm,snd_timer soundcore 15091 1 snd snd_page_alloc 18529 2 snd_intel8x0, snd_pcm ext2 73795 1 parport_pc 32866 1 mac_hid 13253 0 lp 17799 0 parport 46562 3 ppdev, parport_pc,lp usbhid 47199 0 hid 99559 1 usbhid tg3 152032 0 i915 468651 1 floppy 70365 0 drm_kms_helper 46978 1 i915 drm 242038 2 i915,drm_kms_helper i2c_algo_bit 13423 1 i915 video 19596 1 i915 Again there is more but it's giving info on the driver itself. I know it works, I've used it. I assume then that my network got disabled when I installed Ubuntu Server. How do I enable it? I checked and the internet cable is connected to the D-link router. I have also used this same computer for internet access when I had Ubuntu Desktop installed so internet does work.

Read the article

Wireless networks are not detected at start up in Ubuntu 12.04

- by Kanhaiya Mishra

I have recently (three four days ago) installed Ubuntu 12.04 via windows installer i.e. wubi.exe. After the installation completed wireless and Ethernet were both working well. But after restart wireless networks didn't show up while in the network manager both networking and wireless were enabled. Though sometimes after boot it did show the networks available but very rarely. So I went through various posts regarding wireless issues in Ubuntu 12.04 and tried so many things but ended up in nothing satisfactory. I have Broadcom 4313 LAN network controller and brcmsmac driver. Then relying on some suggestions I tried to install bcm-wl driver but couldn't install due to some error in jockeyl.log file. Then i tried fresh installation of the same driver but still could resolve the startup issues with wireless. Then again I reinstalled Ubuntu inside windows using wubi installer. This time again same problem occurred after boot. But this time I successfully installed wl driver before disturbing file-system files of Ubuntu. But again the same issue. This time I noticed some new things: If I inserted Ethernet/LAN cable before startup then wireless networks are available and of course LAN(wired) networks also work. but if i don't plug in cable before startup and then plug it after startup then it didn't detect Ethernet network neither wireless. So I haven't noticed it before that LAN along with wifi also doesn't work after startup. But if i suspend the session and make it sleep and again login then it worked. I tried it every time that WLAN worked perfectly. But still i m unable to resolve that startup problem. Each time i boot first I have to suspend it once then only networks are available. It irritates me each time i reboot/boot my lappy. So please help out of this problem. Any ideas/help regarding this issue would be highly appreciated. Some of the commands that i run gave following results: # lspci 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 12) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 12) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06) 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 06) 00:1c.5 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 6 (rev 06) 00:1d.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a6) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 06) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 6 port SATA AHCI Controller (rev 06) 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 06) 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 06) 03:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) 04:00.0 Ethernet controller: Atheros Communications Inc. AR8152 v1.1 Fast Ethernet (rev c1) ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 02) ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 02) ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 02) ff:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 02) ff:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 02) ff:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 02) # sudo lshw -C network *-network description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: eth1 version: 01 serial: 70:f1:a1:49:b6:ab width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 ip=192.168.1.7 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:f0500000-f0503fff *-network description: Ethernet interface product: AR8152 v1.1 Fast Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 logical name: eth0 version: c1 serial: b8:ac:6f:6b:f7:4a capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI firmware=N/A latency=0 link=no multicast=yes port=twisted pair resources: irq:44 memory:f0400000-f043ffff ioport:2000(size=128) # lsmod | grep wl wl 2568210 0 lib80211 14381 2 lib80211_crypt_tkip,wl # sudo iwlist eth1 scanning eth1 Scan completed : Cell 01 - Address: 30:46:9A:85:DA:9A ESSID:"BH DASHIR 2" Mode:Managed Frequency:2.462 GHz (Channel 11) Quality:4/5 Signal level:-60 dBm Noise level:-98 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK IE: Unknown: DD7F0050F204104A00011010440001021041000100103B000103104700109AFE7D908F8E2D381860668BA2E8D8771021000D4E4554474541522C20496E632E10230009574752363134763130102400095747523631347631301042000538333235381054000800060050F204000110110009574752363134763130100800020084 Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 9 Mb/s 12 Mb/s; 48 Mb/s Cell 02 - Address: C0:3F:0E:EB:45:14 ESSID:"BH DASHIR 3" Mode:Managed Frequency:2.462 GHz (Channel 11) Quality:2/5 Signal level:-71 dBm Noise level:-98 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK IE: Unknown: DD7F0050F204104A00011010440001021041000100103B00010310470010F3C9BBE499D140540F530E7EBEDE2F671021000D4E4554474541522C20496E632E10230009574752363134763130102400095747523631347631301042000538333235381054000800060050F204000110110009574752363134763130100800020084 Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 9 Mb/s 12 Mb/s; 48 Mb/s Cell 03 - Address: A0:21:B7:A8:2F:C0 ESSID:"BH DASHIR 4" Mode:Managed Frequency:2.422 GHz (Channel 3) Quality:1/5 Signal level:-86 dBm Noise level:-98 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK IE: Unknown: DD8B0050F204104A0001101044000102103B0001031047001000000000000010000000A021B7A82FC01021000D4E6574676561722C20496E632E10230009574E523130303076321024000456324831104200046E6F6E651054000800060050F20400011011001B574E5231303030763228576972656C6573732041502D322E344729100800020086103C000103 Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s 48 Mb/s; 54 Mb/s

Read the article

How to troubleshoot ethernet port on laptop

- by Psallas Vassilios

I have a problem with my wired connection. To be more specific, my laptop doesn't seems to recognize that I have plugged in an ethernet cable. I tried to download new drivers for my ethernet card, but I couldn't find any solutions. Maybe because I am new to Linux, so I'm not familiar with running commands in the terminal. OK I have typed the command and here are the results: 00:04.0 Ethernet controller [0200]: Silicon Integrated Systems [SiS] 191 Gigabit Ethernet Adapter [1039:0191] (rev 02) For the second reply I don't know if the following is what you asked me: ?Memory: 3.9 GiB ?Processor: Intel Core 2 Duo CPU P8800 @ 2.66GHz × 2 ?OS type: 32-bit My Ethernet connection had some problem on Windows too. I have changed recently my internet provider, and since then my ethernet cable is not recognized by the laptop. At that time I was still on Windows. I thought that with Ubuntu the problem would be solved, but unfortunately the problem still persists. If someone can help me to solve my problem I'll be thankful. Here are the results of the three first commands you told me to run: lsmod | grep sis190 sis190 22570 0 sudo modprobe sis190 ifconfig eth0 Link encap:Ethernet HWaddr 00:90:f5:90:81:7e UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:185 errors:0 dropped:0 overruns:0 frame:0 TX packets:185 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:22672 (22.6 KB) TX bytes:22672 (22.6 KB) wlan0 Link encap:Ethernet HWaddr 00:25:d3:2c:3a:ae inet addr:192.168.1.72 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::225:d3ff:fe2c:3aae/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:260 errors:0 dropped:0 overruns:0 frame:0 TX packets:363 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:71992 (71.9 KB) TX bytes:52000 (52.0 KB) and the results of running the last two commands: dmesg | grep -e eth -e sis190 [ 0.816667] sis190: sis190 Gigabit Ethernet driver 1.4 loaded [ 0.816728] sis190 0000:00:04.0: setting latency timer to 64 [ 0.816751] sis190: 0000:00:04.0: Read MAC address from EEPROM [ 0.904032] sis190: 0000:00:04.0: Realtek PHY RTL8201 transceiver at address [ 1.416030] sis190: 0000:00:04.0: Using transceiver at address 1 as default [ 1.448235] sis190 0000:00:04.0: eth0: 0000:00:04.0: SiS 191 PCI Gigabit Ethernet adapter at f8410000 (IRQ: 19), 00:90:f5:90:81:7e [ 1.448238] sis190 0000:00:04.0: eth0: GMII mode. [ 1.448243] sis190 0000:00:04.0: eth0: Enabling Auto-negotiation [ 11.560907] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 16.372019] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 16.372265] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 26.424038] sis190 0000:00:04.0: eth0: auto-negotiating... nm-tool NetworkManager Tool State: connected (global) - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: sis190 State: unavailable Default: no HW Address: 00:90:F5:90:81:7E Capabilities: Carrier Detect: yes Wired Properties Carrier: off

Read the article

How to record both audio, Where i have one music running and my microphone is in use?

- by YumYumYum

I have one music playing, and i have microphone open, already the microphone is used by other application. In such case, how can i record that music and the microphone audio to a file? (if possible with command line). Follow up: $ rec new-file.wav Input File : 'default' (alsa) Channels : 2 Sample Rate : 48000 Precision : 16-bit Sample Encoding: 16-bit Signed Integer PCM In:0.00% 00:00:25.94 [00:00:00.00] Out:1.24M [ | ] Clip:0 ^C $ sox -d new-file.wav

Read the article

Weird vps server issue

- by anon-user0

I have an unmanaged linux vps Ubuntu 11.10 (Oneiric Ocelot). I have LNMP installed. Also php-fpm php-apc, varnish, memcache. I have (or rather had) several live sites on it. under normal load the server uses ~700 mb memory. But since last night its using only 20mb~ memory and a lot of the services seems to be down (according to htop) I only see nginx working and mysql starts up and goes does every few minutes on a loop. Here are some information on the server that might help you help me: root@server:~# uname -a Linux server 2.6.18-308.el5.028stab099.3 #1 SMP Wed Mar 7 15:56:00 MSK 2012 i686 i686 i386 GNU/Linux - root@server:~# ifconfig -a lo Link encap:Local Loopback LOOPBACK MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) venet0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:127.0.0.2 P-t-P:127.0.0.2 Bcast:0.0.0.0 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 RX packets:12515 errors:0 dropped:0 overruns:0 frame:0 TX packets:9541 errors:0 dropped:1 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:7191214 (7.1 MB) TX bytes:536726 (536.7 KB) venet0:0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:176.31.158.78 P-t-P:176.31.158.78 Bcast:0.0.0.0 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 - root@server:~# netstat -l Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 *:http-alt *:* LISTEN tcp 0 0 *:ssh *:* LISTEN tcp6 0 0 [::]:http-alt [::]:* LISTEN tcp6 0 0 [::]:ssh [::]:* LISTEN Active UNIX domain sockets (only servers) Proto RefCnt Flags Type State I-Node Path unix 2 [ ACC ] STREAM LISTENING 9307368 @/com/ubuntu/upstart - htop: http://i.stack.imgur.com/NHKYX.png EDIT: Stressed. mind was not working adding log: root@server:~# less /var/log/syslog Jun 27 05:27:42 server syslogd 1.5.0#6ubuntu1: restart. Jun 27 05:39:01 server CRON[9298]: (root) CMD ([ -x /usr/lib/php5/maxlifetime ] && [ -d /var/lib/php5 ] && find /var/lib/php5/ -depth -mindepth 1 -maxdepth 1 -type f -cmin +$(/usr/lib/php5/maxlifetime) -delete) Jun 27 05:40:01 server CRON[9463]: (smmsp) CMD (test -x /etc/init.d/sendmail && /usr/share/sendmail/sendmail cron-msp) Jun 27 05:46:21 server sm-msp-queue[9480]: q5R1R7Ue004056: to=root, ctladdr=root (0/0), delay=00:19:14, xdelay=00:06:18, mailer=relay, pri=122407, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 05:52:39 server sm-msp-queue[9480]: q5QMk7S9009582: to=root, ctladdr=root (0/0), delay=03:06:32, xdelay=00:06:18, mailer=relay, pri=842407, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 06:00:01 server CRON[15671]: (smmsp) CMD (test -x /etc/init.d/sendmail && /usr/share/sendmail/sendmail cron-msp) Jun 27 06:06:22 server sm-msp-queue[15690]: q5R1R7Ue004056: to=root, ctladdr=root (0/0), delay=00:39:15, xdelay=00:06:18, mailer=relay, pri=212407, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 06:09:01 server CRON[18114]: (root) CMD ([ -x /usr/lib/php5/maxlifetime ] && [ -d /var/lib/php5 ] && find /var/lib/php5/ -depth -mindepth 1 -maxdepth 1 -type f -cmin +$(/usr/lib/php5/maxlifetime) -delete) Jun 27 06:12:40 server sm-msp-queue[15690]: q5QMk7S9009582: to=root, ctladdr=root (0/0), delay=03:26:33, xdelay=00:06:18, mailer=relay, pri=932407, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 06:20:02 server CRON[21888]: (smmsp) CMD (test -x /etc/init.d/sendmail && /usr/share/sendmail/sendmail cron-msp) Jun 27 06:26:22 server sm-msp-queue[21907]: q5R1R7Ue004056: to=root, ctladdr=root (0/0), delay=00:59:15, xdelay=00:06:18, mailer=relay, pri=302407, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 06:27:02 server CRON[24021]: (root) CMD (cd / && run-parts --report /etc/cron.hourly) Jun 27 06:32:40 server sm-msp-queue[21907]: q5QMk7S9009582: to=root, ctladdr=root (0/0), delay=03:46:33, xdelay=00:06:18, mailer=relay, pri=1022407, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 06:39:01 server CRON[27941]: (root) CMD ([ -x /usr/lib/php5/maxlifetime ] && [ -d /var/lib/php5 ] && find /var/lib/php5/ -depth -mindepth 1 -maxdepth 1 -type f -cmin +$(/usr/lib/php5/maxlifetime) -delete) Jun 27 06:40:02 server CRON[28110]: (smmsp) CMD (test -x /etc/init.d/sendmail && /usr/share/sendmail/sendmail cron-msp) Jun 27 06:46:22 server sm-msp-queue[28125]: q5R1R7Ue004056: to=root, ctladdr=root (0/0), delay=01:19:15, xdelay=00:06:18, mailer=relay, pri=392407, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 06:52:40 server sm-msp-queue[28125]: q5QMk7S9009582: to=root, ctladdr=root (0/0), delay=04:06:33, xdelay=00:06:18, mailer=relay, pri=1112407, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 06:52:40 server sm-msp-queue[28125]: q5QMk7S9009582: q5R2e4uo028125: sender notify: Warning: could not send message for past 4 hours Jun 27 06:52:44 server sm-msp-queue[28125]: q5R2e4uo028125: to=root, delay=00:00:04, xdelay=00:00:04, mailer=relay, pri=33690, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 07:00:02 server CRON[1543]: (smmsp) CMD (test -x /etc/init.d/sendmail && /usr/share/sendmail/sendmail cron-msp) Jun 27 07:06:21 server sm-msp-queue[1560]: q5R2e4uo028125: to=root, delay=00:13:41, xdelay=00:06:18, mailer=relay, pri=123690, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 07:09:01 server CRON[3986]: (root) CMD ([ -x /usr/lib/php5/maxlifetime ] && [ -d /var/lib/php5 ] && find /var/lib/php5/ -depth -mindepth 1 -maxdepth 1 -type f -cmin +$(/usr/lib/php5/maxlifetime) -delete) Jun 27 07:12:39 server sm-msp-queue[1560]: q5R1R7Ue004056: to=root, ctladdr=root (0/0), delay=01:45:32, xdelay=00:06:18, mailer=relay, pri=482407, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 07:18:57 server sm-msp-queue[1560]: q5QMk7S9009582: to=root, ctladdr=root (0/0), delay=04:32:50, xdelay=00:06:18, mailer=relay, pri=1202407, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 07:20:02 server CRON[7760]: (smmsp) CMD (test -x /etc/init.d/sendmail && /usr/share/sendmail/sendmail cron-msp) Jun 27 07:26:22 server sm-msp-queue[7775]: q5R2e4uo028125: to=root, delay=00:33:42, xdelay=00:06:18, mailer=relay, pri=213690, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 07:27:01 server CRON[9887]: (root) CMD (cd / && run-parts --report /etc/cron.hourly) Jun 27 07:32:40 server sm-msp-queue[7775]: q5R1R7Ue004056: to=root, ctladdr=root (0/0), delay=02:05:33, xdelay=00:06:18, mailer=relay, pri=572407, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 07:38:58 server sm-msp-queue[7775]: q5QMk7S9009582: to=root, ctladdr=root (0/0), delay=04:52:51, xdelay=00:06:18, mailer=relay, pri=1292407, relay=[127.0.0.1] [127.0.0.1], dsn=4.0.0, stat=Deferred: Connection timed out with [127.0.0.1] Jun 27 07:39:01 server CRON[13813]: (root) CMD ([ -x /usr/lib/php5/maxlifetime ] && [ -d /var/lib/php5 ] && find /var/lib/php5/ -depth -mindepth : root@server:~# df -h Filesystem Size Used Avail Use% Mounted on /dev/simfs 20G 2.3G 18G 12% / - Jun 26 16:22:41 server varnishd[1413]: Child (32425) died signal=3 Jun 26 16:22:41 server varnishd[1413]: child (21687) Started Jun 26 16:22:41 server varnishd[1413]: Child (21687) said Child starts Jun 26 16:22:41 server varnishd[1413]: Child (21687) said SMF.s0 mmap'ed 1073741824 bytes of 1073741824 Jun 26 16:34:28 server -- MARK -- Jun 26 16:54:29 server -- MARK -- Jun 26 17:14:29 server -- MARK -- Jun 26 17:34:29 server -- MARK -- Jun 26 17:54:29 server -- MARK -- Jun 26 18:14:29 server -- MARK -- Jun 26 18:34:29 server -- MARK -- Jun 26 18:54:29 server -- MARK -- Jun 26 19:14:29 server -- MARK -- Jun 26 19:34:29 server -- MARK -- Jun 26 19:54:29 server -- MARK -- Jun 26 20:14:29 server -- MARK -- Jun 26 20:34:29 server -- MARK -- Jun 26 20:48:12 server exiting on signal 15 Jun 26 20:51:58 server syslogd 1.5.0#6ubuntu1: restart. Jun 26 20:52:01 server varnishd[1324]: Platform: Linux,2.6.18-308.el5.028stab099.3,i686,-sfile,-smalloc,-hcritbit Jun 26 21:11:58 server -- MARK -- Jun 26 21:31:58 server -- MARK -- Jun 26 21:51:58 server -- MARK -- Jun 26 22:11:58 server -- MARK -- Jun 26 22:31:58 server -- MARK -- Jun 26 22:51:58 server -- MARK -- Jun 26 23:11:58 server -- MARK -- Jun 26 23:31:58 server -- MARK -- Jun 26 23:51:58 server -- MARK -- Jun 27 00:11:58 server -- MARK -- Jun 27 00:23:42 server exiting on signal 15 Jun 27 02:21:10 server syslogd 1.5.0#6ubuntu1: restart. Jun 27 02:21:12 server varnishd[1341]: Platform: Linux,2.6.18-308.el5.028stab099.3,i686,-sfile,-smalloc,-hcritbit Jun 27 02:41:10 server -- MARK -- Jun 27 02:46:41 server syslogd 1.5.0#6ubuntu1: restart. Jun 27 03:20:44 server syslogd 1.5.0#6ubuntu1: restart. Jun 27 03:20:46 server varnishd[1238]: Platform: Linux,2.6.18-308.el5.028stab099.3,i686,-sfile,-smalloc,-hcritbit Jun 27 03:20:46 server varnishd[1238]: child (1239) Started Jun 27 03:20:46 server varnishd[1238]: Child (1239) said Child starts Jun 27 03:20:46 server varnishd[1238]: Child (1239) said SMF.s0 mmap'ed 1073741824 bytes of 1073741824 Jun 27 03:32:52 server exiting on signal 15 Jun 27 03:33:16 server syslogd 1.5.0#6ubuntu1: restart. Jun 27 03:33:31 server varnishd[1372]: Platform: Linux,2.6.18-308.el5.028stab099.3,i686,-sfile,-smalloc,-hcritbit Jun 27 03:53:16 server -- MARK -- Jun 27 04:13:16 server -- MARK -- Jun 27 04:33:16 server -- MARK -- Jun 27 04:53:16 server -- MARK -- Jun 27 05:13:16 server -- MARK -- Jun 27 05:27:42 server syslogd 1.5.0#6ubuntu1: restart. Jun 27 05:53:17 server -- MARK -- Jun 27 06:13:17 server -- MARK -- Jun 27 06:33:17 server -- MARK -- Jun 27 06:53:17 server -- MARK -- Jun 27 07:13:17 server -- MARK -- Jun 27 07:33:17 server -- MARK -- Jun 27 07:53:17 server -- MARK -- Jun 27 08:13:17 server -- MARK -- Jun 27 08:33:17 server -- MARK -- Jun 27 08:53:17 server -- MARK -- Jun 27 09:13:17 server -- MARK -- Jun 27 09:33:17 server -- MARK -- Jun 27 09:53:17 server -- MARK -- Jun 27 10:13:17 server -- MARK -- Jun 27 10:33:17 server -- MARK -- Jun 27 10:53:17 server -- MARK -- Jun 27 11:13:17 server -- MARK -- Jun 27 11:33:17 server -- MARK -- Jun 27 11:53:18 server -- MARK -- Jun 27 12:13:18 server -- MARK -- Jun 27 12:33:18 server -- MARK -- Jun 27 12:53:18 server -- MARK -- Jun 27 13:13:18 server -- MARK -- Jun 27 13:33:18 server -- MARK -- Jun 27 13:53:18 server -- MARK -- Jun 27 14:13:18 server -- MARK -- Jun 27 14:33:18 server -- MARK -- Jun 27 14:53:18 server -- MARK -- -- root@server:~# cat /var/log/nginx/error.log 2012/06/27 03:32:54 [alert] 1199#0: worker process 1203 exited on signal 9 2012/06/27 03:32:54 [alert] 1199#0: worker process 1200 exited on signal 9 2012/06/27 03:32:54 [alert] 1199#0: worker process 1201 exited on signal 9 2012/06/27 03:32:54 [alert] 1199#0: worker process 1202 exited on signal 9 root@server:~# cat /var/log/nginx/access.log 31.210.99.87 - - [27/Jun/2012:09:09:08 +0400] "GET /w00tw00t.at.ISC.SANS.DFind:) HTTP/1.1" 400 172 "-" "-" 88.191.138.103 - - [27/Jun/2012:13:27:08 +0400] "GET /cms/cmx.jsp HTTP/1.1" 301 184 "-" "-" 88.191.138.103 - - [27/Jun/2012:13:27:08 +0400] "GET /iesvc/iesvc.jsp HTTP/1.1" 301 184 "-" "-" 88.191.138.103 - - [27/Jun/2012:13:27:08 +0400] "GET /cmd2/index.jsp HTTP/1.1" 301 184 "-" "-" 88.191.138.103 - - [27/Jun/2012:13:27:09 +0400] "GET /cmd/index.jsp HTTP/1.1" 301 184 "-" "-" 58.97.147.197 - - [27/Jun/2012:17:17:19 +0400] "GET / HTTP/1.1" 301 184 "-" "Mozilla/5.0 (Macintosh; Intel Mac OS X 10_7_4) AppleWebKit/536.5 (KHTML, like Gecko) Chrome/19.0.1084.56 Safari/536.5" 58.97.147.197 - - [27/Jun/2012:17:17:37 +0400] "GET / HTTP/1.1" 301 184 "-" "Mozilla/5.0 (Macintosh; Intel Mac OS X 10_7_4) AppleWebKit/536.5 (KHTML, like Gecko) Chrome/19.0.1084.56 Safari/536.5" 58.97.147.197 - - [27/Jun/2012:17:17:38 +0400] "-" 400 0 "-" "-" 58.97.147.197 - - [27/Jun/2012:17:17:38 +0400] "-" 400 0 "-" "-" 58.97.147.197 - - [27/Jun/2012:17:17:48 +0400] "-" 400 0 "-" "-" - root@server:~# cat /var/log/daemon.log Jun 26 20:48:10 server xinetd[1177]: Exiting... Jun 26 20:51:58 server xinetd[1174]: Reading included configuration file: /etc/xinetd.d/daytime [file=/etc/xinetd.d/daytime] [line=28] Jun 26 20:51:58 server xinetd[1174]: Reading included configuration file: /etc/xinetd.d/discard [file=/etc/xinetd.d/discard] [line=26] Jun 26 20:51:58 server xinetd[1174]: Reading included configuration file: /etc/xinetd.d/echo [file=/etc/xinetd.d/echo] [line=25] Jun 26 20:51:58 server xinetd[1174]: Reading included configuration file: /etc/xinetd.d/time [file=/etc/xinetd.d/time] [line=26] Jun 26 20:51:58 server xinetd[1174]: removing chargen Jun 26 20:51:58 server xinetd[1174]: removing chargen Jun 26 20:51:58 server xinetd[1174]: removing daytime Jun 26 20:51:58 server xinetd[1174]: removing daytime Jun 26 20:51:58 server xinetd[1174]: removing discard Jun 26 20:51:58 server xinetd[1174]: removing discard Jun 26 20:51:58 server xinetd[1174]: removing echo Jun 26 20:51:58 server xinetd[1174]: removing echo Jun 26 20:51:58 server xinetd[1174]: removing time Jun 26 20:51:58 server xinetd[1174]: removing time Jun 26 20:51:58 server xinetd[1174]: xinetd Version 2.3.14 started with libwrap loadavg options compiled in. Jun 26 20:51:58 server xinetd[1174]: Started working: 0 available services Jun 26 20:52:01 server vnstatd[1330]: vnStat daemon 1.11 started. Jun 26 20:52:01 server vnstatd[1330]: Monitoring: venet0 Jun 27 00:23:41 server xinetd[1174]: Exiting... Jun 27 02:21:12 server vnstatd[1349]: vnStat daemon 1.11 started. Jun 27 02:21:12 server vnstatd[1349]: Monitoring: venet0 Jun 27 03:20:44 server xinetd[1166]: attribute: disable should not be in default section [file=/etc/xinetd.conf] [line=12] Jun 27 03:20:44 server xinetd[1166]: Reading included configuration file: /etc/xinetd.d/chargen [file=/etc/xinetd.conf] [line=15] Jun 27 03:20:44 server xinetd[1166]: Reading included configuration file: /etc/xinetd.d/daytime [file=/etc/xinetd.d/daytime] [line=28] Jun 27 03:20:44 server xinetd[1166]: Reading included configuration file: /etc/xinetd.d/discard [file=/etc/xinetd.d/discard] [line=26] Jun 27 03:20:44 server xinetd[1166]: Reading included configuration file: /etc/xinetd.d/echo [file=/etc/xinetd.d/echo] [line=25] Jun 27 03:20:44 server xinetd[1166]: Reading included configuration file: /etc/xinetd.d/time [file=/etc/xinetd.d/time] [line=26] Jun 27 03:20:44 server xinetd[1166]: removing chargen Jun 27 03:20:44 server xinetd[1166]: removing chargen Jun 27 03:20:44 server xinetd[1166]: removing daytime Jun 27 03:20:44 server xinetd[1166]: removing daytime Jun 27 03:20:44 server xinetd[1166]: removing discard Jun 27 03:20:44 server xinetd[1166]: removing discard Jun 27 03:20:44 server xinetd[1166]: removing echo Jun 27 03:20:44 server xinetd[1166]: removing echo Jun 27 03:20:44 server xinetd[1166]: removing time Jun 27 03:20:44 server xinetd[1166]: removing time Jun 27 03:20:44 server xinetd[1166]: xinetd Version 2.3.14 started with libwrap loadavg options compiled in. Jun 27 03:20:44 server xinetd[1166]: Started working: 0 available services Jun 27 03:20:46 server vnstatd[1249]: vnStat daemon 1.11 started. Jun 27 03:20:46 server vnstatd[1249]: Monitoring: venet0 Jun 27 03:32:41 server xinetd[1166]: Exiting... Jun 27 03:33:32 server vnstatd[1380]: vnStat daemon 1.11 started. Jun 27 03:33:32 server vnstatd[1380]: Monitoring: venet0 root@server:~# - Anything else you need let me know

Read the article

What do I do when I get a Linux kernel bug?

- by raldi

I just bought a tiny computer called a fit-pc2 which came with a somewhat customized Ubuntu 9.10 installation. uname -a reports: Linux 2.6.31-34-fitpc2 #7 SMP Thu Apr 22 17:43:26 IDT 2010 i686 GNU/Linux It seems that after several hours of running with heavy network load, all networking ceases and I get the following in kern.log: BUG: unable to handle kernel paging request at ff09dfc0 IP: [<c0150300>] kthread_should_stop+0x10/0x20 *pde = 00000000 Oops: 0000 [#1] SMP last sysfs file: /sys/devices/pci0000:00/0000:00:1d.7/usb1/idVendor Modules linked in: binfmt_misc ppdev sbc_fitpc2_wdt snd_usb_audio snd_usb_lib i2c_isch sch_gpio snd_seq_dummy snd_hda_intel snd_pcm_oss snd_seq_oss snd_seq_midi snd_rawmidi snd_mixer_oss snd_seq_midi_event snd_seq snd_pcm snd_timer snd_page_alloc snd_seq_device iptable_filter ip_tables x_tables snd_hwdep lpc_sch snd psmouse rt2860sta(C) uvcvideo video pl2303 soundcore mfd_core output videodev v4l1_compat lirc_igorplugusb lirc_dev serio_raw lp parport usbhid r8169 mii iegd_mod drm agpgart Pid: 16, comm: kblockd/1 Tainted: G C (2.6.31-34-fitpc2 #7) SBC-FITPC2 EIP: 0060:[<c0150300>] EFLAGS: 00010246 CPU: 1 EIP is at kthread_should_stop+0x10/0x20 EAX: ff09dfc4 EBX: c180cbac ECX: 0109d000 EDX: f709df98 ESI: f709df98 EDI: c180cba0 EBP: f709dfb8 ESP: f709df90 DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068 Process kblockd/1 (pid: 16, ti=f709c000 task=f7084b60 task.ti=f709c000) Stack: c014c14d c180cba4 00000000 f7084b60 c0150770 f709dfa4 f709dfa4 f7023ef4 <0> c180cba0 c014c0d0 f709dfe0 c015047c 00000000 00000000 00000000 f709dfcc <0> f709dfcc c0150400 00000000 00000000 00000000 c0103ce7 f7023ef4 00000000 Call Trace: [<c014c14d>] ? worker_thread+0x7d/0xe0 [<c0150770>] ? autoremove_wake_function+0x0/0x40 [<c014c0d0>] ? worker_thread+0x0/0xe0 [<c015047c>] ? kthread+0x7c/0x90 [<c0150400>] ? kthread+0x0/0x90 [<c0103ce7>] ? kernel_thread_helper+0x7/0x10 Code: a6 8b 55 0c 8d 4d e0 89 f8 89 34 24 e8 7a fd ff ff 89 c3 eb 92 90 90 90 90 90 90 55 64 a1 00 80 76 c0 8b 80 70 02 00 00 89 e5 5d <8b> 40 fc c3 8d b6 00 00 00 00 8d bf 00 00 00 00 55 ba d7 86 62 EIP: [<c0150300>] kthread_should_stop+0x10/0x20 SS:ESP 0068:f709df90 CR2: 00000000ff09dfc0 ---[ end trace 06004df70b9cf435 ]--- BUG: unable to handle kernel paging request at ff09dfc8 IP: [<c0521bc8>] _spin_lock_irqsave+0x18/0x30 *pde = 00000000 Oops: 0002 [#2] SMP last sysfs file: /sys/devices/pci0000:00/0000:00:1d.7/usb1/idVendor Modules linked in: binfmt_misc ppdev sbc_fitpc2_wdt snd_usb_audio snd_usb_lib i2c_isch sch_gpio snd_seq_dummy snd_hda_intel snd_pcm_oss snd_seq_oss snd_seq_midi snd_rawmidi snd_mixer_oss snd_seq_midi_event snd_seq snd_pcm snd_timer snd_page_alloc snd_seq_device iptable_filter ip_tables x_tables snd_hwdep lpc_sch snd psmouse rt2860sta(C) uvcvideo video pl2303 soundcore mfd_core output videodev v4l1_compat lirc_igorplugusb lirc_dev serio_raw lp parport usbhid r8169 mii iegd_mod drm agpgart Pid: 16, comm: kblockd/1 Tainted: G D C (2.6.31-34-fitpc2 #7) SBC-FITPC2 EIP: 0060:[<c0521bc8>] EFLAGS: 00010086 CPU: 1 EIP is at _spin_lock_irqsave+0x18/0x30 EAX: 00000100 EBX: ff09dfc8 ECX: 00000286 EDX: ff09dfc8 ESI: f7084b60 EDI: ff09dfc4 EBP: f709dd88 ESP: f709dd88 DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068 Process kblockd/1 (pid: 16, ti=f709c000 task=f7084b60 task.ti=f709c000) Stack: f709dda4 c0127c0b 00000082 00000001 ff09dfc4 f7084b60 00000000 f709ddd0 <0> c0137fd2 00000086 f70954c4 00000000 f7098480 f709ddf0 f7094fc0 f7084b60 <0> 00000000 00000009 f709ddf0 c013c3f8 00000001 c1807c60 f709ddf0 f7084b60 Call Trace: [<c0127c0b>] ? complete+0x1b/0x60 [<c0137fd2>] ? mm_release+0x52/0xf0 [<c013c3f8>] ? exit_mm+0x18/0x110 [<c013c6db>] ? do_exit+0xfb/0x2e0 [<c013998a>] ? print_oops_end_marker+0x2a/0x30 [<c0522aab>] ? oops_end+0x8b/0xd0 [<c011eac4>] ? no_context+0xb4/0xd0 [<c011eb1d>] ? __bad_area_nosemaphore+0x3d/0x1a0 [<c0133a56>] ? load_balance_newidle+0x96/0x320 [<c011ec92>] ? bad_area_nosemaphore+0x12/0x20 [<c0524106>] ? do_page_fault+0x2f6/0x380 [<c012cc30>] ? finish_task_switch+0x50/0xe0 [<c0523e10>] ? do_page_fault+0x0/0x380 [<c0522006>] ? error_code+0x66/0x70 [<c0523e10>] ? do_page_fault+0x0/0x380 [<c0150300>] ? kthread_should_stop+0x10/0x20 [<c014c14d>] ? worker_thread+0x7d/0xe0 [<c0150770>] ? autoremove_wake_function+0x0/0x40 [<c014c0d0>] ? worker_thread+0x0/0xe0 [<c015047c>] ? kthread+0x7c/0x90 [<c0150400>] ? kthread+0x0/0x90 [<c0103ce7>] ? kernel_thread_helper+0x7/0x10 Code: 00 00 00 55 89 e5 f0 83 28 01 79 05 e8 02 ff ff ff 5d c3 55 89 c2 89 e5 9c 58 8d 74 26 00 89 c1 fa 90 8d 74 26 00 b8 00 01 00 00 <f0> 66 0f c1 02 38 e0 74 06 f3 90 8a 02 eb f6 89 c8 5d c3 90 8d EIP: [<c0521bc8>] _spin_lock_irqsave+0x18/0x30 SS:ESP 0068:f709dd88 CR2: 00000000ff09dfc8 ---[ end trace 06004df70b9cf436 ]--- Fixing recursive fault but reboot is needed! This seems to happen at least once a day. How do I even begin to debug this?

Read the article

What do I do when I get a Linux kernel bug?

- by raldi

I just bought a tiny computer called a fit-pc2 which came with a somewhat customized Ubuntu 9.10 installation. uname -a reports: Linux 2.6.31-34-fitpc2 #7 SMP Thu Apr 22 17:43:26 IDT 2010 i686 GNU/Linux It seems that after several hours of running with heavy network load, all networking ceases and I get the following in kern.log: BUG: unable to handle kernel paging request at ff09dfc0 IP: [<c0150300>] kthread_should_stop+0x10/0x20 *pde = 00000000 Oops: 0000 [#1] SMP last sysfs file: /sys/devices/pci0000:00/0000:00:1d.7/usb1/idVendor Modules linked in: binfmt_misc ppdev sbc_fitpc2_wdt snd_usb_audio snd_usb_lib i2c_isch sch_gpio snd_seq_dummy snd_hda_intel snd_pcm_oss snd_seq_oss snd_seq_midi snd_rawmidi snd_mixer_oss snd_seq_midi_event snd_seq snd_pcm snd_timer snd_page_alloc snd_seq_device iptable_filter ip_tables x_tables snd_hwdep lpc_sch snd psmouse rt2860sta(C) uvcvideo video pl2303 soundcore mfd_core output videodev v4l1_compat lirc_igorplugusb lirc_dev serio_raw lp parport usbhid r8169 mii iegd_mod drm agpgart Pid: 16, comm: kblockd/1 Tainted: G C (2.6.31-34-fitpc2 #7) SBC-FITPC2 EIP: 0060:[<c0150300>] EFLAGS: 00010246 CPU: 1 EIP is at kthread_should_stop+0x10/0x20 EAX: ff09dfc4 EBX: c180cbac ECX: 0109d000 EDX: f709df98 ESI: f709df98 EDI: c180cba0 EBP: f709dfb8 ESP: f709df90 DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068 Process kblockd/1 (pid: 16, ti=f709c000 task=f7084b60 task.ti=f709c000) Stack: c014c14d c180cba4 00000000 f7084b60 c0150770 f709dfa4 f709dfa4 f7023ef4 <0> c180cba0 c014c0d0 f709dfe0 c015047c 00000000 00000000 00000000 f709dfcc <0> f709dfcc c0150400 00000000 00000000 00000000 c0103ce7 f7023ef4 00000000 Call Trace: [<c014c14d>] ? worker_thread+0x7d/0xe0 [<c0150770>] ? autoremove_wake_function+0x0/0x40 [<c014c0d0>] ? worker_thread+0x0/0xe0 [<c015047c>] ? kthread+0x7c/0x90 [<c0150400>] ? kthread+0x0/0x90 [<c0103ce7>] ? kernel_thread_helper+0x7/0x10 Code: a6 8b 55 0c 8d 4d e0 89 f8 89 34 24 e8 7a fd ff ff 89 c3 eb 92 90 90 90 90 90 90 55 64 a1 00 80 76 c0 8b 80 70 02 00 00 89 e5 5d <8b> 40 fc c3 8d b6 00 00 00 00 8d bf 00 00 00 00 55 ba d7 86 62 EIP: [<c0150300>] kthread_should_stop+0x10/0x20 SS:ESP 0068:f709df90 CR2: 00000000ff09dfc0 ---[ end trace 06004df70b9cf435 ]--- BUG: unable to handle kernel paging request at ff09dfc8 IP: [<c0521bc8>] _spin_lock_irqsave+0x18/0x30 *pde = 00000000 Oops: 0002 [#2] SMP last sysfs file: /sys/devices/pci0000:00/0000:00:1d.7/usb1/idVendor Modules linked in: binfmt_misc ppdev sbc_fitpc2_wdt snd_usb_audio snd_usb_lib i2c_isch sch_gpio snd_seq_dummy snd_hda_intel snd_pcm_oss snd_seq_oss snd_seq_midi snd_rawmidi snd_mixer_oss snd_seq_midi_event snd_seq snd_pcm snd_timer snd_page_alloc snd_seq_device iptable_filter ip_tables x_tables snd_hwdep lpc_sch snd psmouse rt2860sta(C) uvcvideo video pl2303 soundcore mfd_core output videodev v4l1_compat lirc_igorplugusb lirc_dev serio_raw lp parport usbhid r8169 mii iegd_mod drm agpgart Pid: 16, comm: kblockd/1 Tainted: G D C (2.6.31-34-fitpc2 #7) SBC-FITPC2 EIP: 0060:[<c0521bc8>] EFLAGS: 00010086 CPU: 1 EIP is at _spin_lock_irqsave+0x18/0x30 EAX: 00000100 EBX: ff09dfc8 ECX: 00000286 EDX: ff09dfc8 ESI: f7084b60 EDI: ff09dfc4 EBP: f709dd88 ESP: f709dd88 DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068 Process kblockd/1 (pid: 16, ti=f709c000 task=f7084b60 task.ti=f709c000) Stack: f709dda4 c0127c0b 00000082 00000001 ff09dfc4 f7084b60 00000000 f709ddd0 <0> c0137fd2 00000086 f70954c4 00000000 f7098480 f709ddf0 f7094fc0 f7084b60 <0> 00000000 00000009 f709ddf0 c013c3f8 00000001 c1807c60 f709ddf0 f7084b60 Call Trace: [<c0127c0b>] ? complete+0x1b/0x60 [<c0137fd2>] ? mm_release+0x52/0xf0 [<c013c3f8>] ? exit_mm+0x18/0x110 [<c013c6db>] ? do_exit+0xfb/0x2e0 [<c013998a>] ? print_oops_end_marker+0x2a/0x30 [<c0522aab>] ? oops_end+0x8b/0xd0 [<c011eac4>] ? no_context+0xb4/0xd0 [<c011eb1d>] ? __bad_area_nosemaphore+0x3d/0x1a0 [<c0133a56>] ? load_balance_newidle+0x96/0x320 [<c011ec92>] ? bad_area_nosemaphore+0x12/0x20 [<c0524106>] ? do_page_fault+0x2f6/0x380 [<c012cc30>] ? finish_task_switch+0x50/0xe0 [<c0523e10>] ? do_page_fault+0x0/0x380 [<c0522006>] ? error_code+0x66/0x70 [<c0523e10>] ? do_page_fault+0x0/0x380 [<c0150300>] ? kthread_should_stop+0x10/0x20 [<c014c14d>] ? worker_thread+0x7d/0xe0 [<c0150770>] ? autoremove_wake_function+0x0/0x40 [<c014c0d0>] ? worker_thread+0x0/0xe0 [<c015047c>] ? kthread+0x7c/0x90 [<c0150400>] ? kthread+0x0/0x90 [<c0103ce7>] ? kernel_thread_helper+0x7/0x10 Code: 00 00 00 55 89 e5 f0 83 28 01 79 05 e8 02 ff ff ff 5d c3 55 89 c2 89 e5 9c 58 8d 74 26 00 89 c1 fa 90 8d 74 26 00 b8 00 01 00 00 <f0> 66 0f c1 02 38 e0 74 06 f3 90 8a 02 eb f6 89 c8 5d c3 90 8d EIP: [<c0521bc8>] _spin_lock_irqsave+0x18/0x30 SS:ESP 0068:f709dd88 CR2: 00000000ff09dfc8 ---[ end trace 06004df70b9cf436 ]--- Fixing recursive fault but reboot is needed! This seems to happen at least once a day. How do I even begin to debug this?

Search Results

Search found 3935 results on 158 pages for 'garreth 00'.

Page 21/158 | < Previous Page | 17 18 19 20 21 22 23 24 25 26 27 28 | Next Page >

- by Mark

- by Tom Brito

- by Smollet

- by valya

- by unknown (google)

- by m.edmondson

- by El Barto

- by zertux

- by Albert Widjaja

- by El Barto

- by hradecek

- by Alvin G. Matunog

- by jyavenard

- by andy

- by vshenoy

- by menjaraz

- by sf

- by Werner

- by jason328

- by Kanhaiya Mishra

- by Psallas Vassilios

- by YumYumYum

- by anon-user0

- by raldi

- by raldi

< Previous Page | 17 18 19 20 21 22 23 24 25 26 27 28 | Next Page >