Search Results

Search found 1817 results on 73 pages for 'kevin 82'.

Page 21/73 | < Previous Page | 17 18 19 20 21 22 23 24 25 26 27 28  | Next Page >

  • Can't access external hard drives or thumb drives

    - by calden
    I am not a complete linux noob but I don't know a lot either and would greatly appreciate some help with this. I just installed Ubuntu 10.10 onto my laptop. Everything is working great however USB devices such as thumb drives and external hard drives wont show up. I have been looking around a bit and when I run sudo fdisk -l it displays this: Disk /dev/sda: 250.1 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00065684 Device Boot Start End Blocks Id System /dev/sda1 * 1 29255 234983424 83 Linux /dev/sda2 29255 30402 9212929 5 Extended /dev/sda5 29255 30402 9212928 82 Linux swap / Solaris Disk /dev/sdb: 16.0 GB, 16026435072 bytes 64 heads, 32 sectors/track, 15283 cylinders Units = cylinders of 2048 * 512 = 1048576 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000df90d Device Boot Start End Blocks Id System /dev/sdb1 * 1 15283 15649776 7 HPFS/NTFS It does seem to display my 16 gig thumb drive but other then seeing it here I cant access it to read and write files to it. It does the same with my external hard drive. I know those devices work as I have tried them on my other computer and they are working fine. Also this is what is in fstab if this will help anybody help me: proc /proc proc nodev,noexec,nosuid 0 0 /dev/sdb1 / ext4 errors=remount-ro 0 1 /dev/sdb5 none swap sw 0 0 Thank you very much for the help everyone.

    Read the article

  • which drive do I mount

    - by Crash893
    I have a system hdd then two raid1 hard drives I see that sda1 is the system drive but when i do a fdisk -l I get the following results so which of the following do i need to mount to get the "raid" drive and not the individual hdd? root@Mxxxx-PDC:/etc/samba# fdisk -l Disk /dev/sda: 251.0 GB, 251000193024 bytes 255 heads, 63 sectors/track, 30515 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x000762dc Device Boot Start End Blocks Id System /dev/sda1 * 1 30328 243609628+ 83 Linux /dev/sda2 30329 30515 1502077+ 5 Extended /dev/sda5 30329 30515 1502046 82 Linux swap / Solaris Disk /dev/sdb: 400.0 GB, 400088457216 bytes 255 heads, 63 sectors/track, 48641 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdb1 1 48641 390708801 83 Linux Disk /dev/sdc: 250.0 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x0009f4b2 Device Boot Start End Blocks Id System /dev/sdc1 * 1 255 2048256 fd Linux raid autodetect /dev/sdc2 256 30401 242147745 fd Linux raid autodetect Disk /dev/sdd: 250.0 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x000b7f4c Device Boot Start End Blocks Id System /dev/sdd1 * 1 255 2048256 fd Linux raid autodetect /dev/sdd2 256 30401 242147745 fd Linux raid autodetect

    Read the article

  • Cannot Restore GRUB (Ubuntu 11.04 + Win 7)

    - by Benny
    I'm trying to fix GRUB on my PC, but I'm running into serious issues doing so. Any help would be greatly appreciated as I'm completely crippled right now. Here is the sequence of events for this PC: Installed Windows 7 Split full disk into two partitions (one for win7 and one for multimedia) Long time passed Split one of the partitions into two again Installed Ubuntu 11.04 on new partition A little time passed Windows 7 acting up, reinstall Ubuntu GRUB gone Tried restoring GRUB by mounting and grub-install from live USB Tried switching to a live CD instead of USB (thinking it might be the drive) Now I don't see GRUB and I'm getting "input/output" errors An example i/o error: ubuntu@ubuntu:~$ sudo fdisk -l Disk /dev/sda: 750.2 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xbe86aff6 Device Boot Start End Blocks Id System /dev/sda1 * 1 48727 391393280 7 HPFS/NTFS /dev/sda2 48727 77063 227612647+ 7 HPFS/NTFS /dev/sda3 77063 91202 113566721 5 Extended /dev/sda5 77063 90622 108908544 83 Linux /dev/sda6 90622 91202 4657152 82 Linux swap / Solaris ubuntu@ubuntu:~$ sudo mount /dev/sda5 /mnt ubuntu@ubuntu:~$ sudo grub-install --root-directory=/mnt /dev/sda mkdir: cannot create directory `/mnt/boot': Input/output error ubuntu@ubuntu:~$ cd /mnt ubuntu@ubuntu:/mnt$ ls ls: cannot access etc: Input/output error

    Read the article

  • Windows Store now open to ALL developers

    - by CSharpZealot
    A little late, but it should be announced here too... Today’s an especially great day to be a developer. We’re very excited to announce the last significant milestone in the rollout of the Windows Store before the general availability of Windows 8 on October 26. The Store is now open for app submissions from all developers – individuals and companies – in our supported markets, and we’ve added 82 more app submission markets! Now, developers from 120 markets can publish Windows Store apps. Ted Dworkin, Partner Program Manager for the Store, authored this post. --Antoine Source: http://blogs.msdn.com/b/windowsstore/archive/2012/09/11/windows-store-now-open-to-all-developers.aspx About two weeks ago the Windows Store was opened and with the upcoming general availability of Windows 8 in October, it seems that it was good timing. In addition to the store being opened, Microsoft also announced that the MSDN, BizSpark and DreamSpark will get a 1-year Windows Store developer account. That's a different tact than what we saw for the Windows Phone 7, where we didn't get that subscription included. We're already seeing new apps showing up faster and faster, so with the addition of 86 more markets we're only going to see more apps than ever available. Since i'm now back on a Windows 8 platform (was out for about a month) I'm going to start blogging more content around the Windows 8 developer experience. Next stop for me...get my hands on a Windows 8 surface device as quickly as possible :) Keep coding!

    Read the article

  • How to restore Windows7 after restore ubuntu bootloader?

    - by Mateusz Rogulski
    At first I will describe my situation in a few points: I have installed Windows7, and then Ubuntu 11.04 on my machine. Then everything works fine and at start of system I have screen from linux where I can choose the system. Then I reinstall Windows7 and install Windows 8 on other partition. Then I can choose between Win7 and win8 when I start system. Then I need my Ubuntu back so I want restore my bootloader from Ubuntu. I boot Ubuntu from USB and in terminal write this commands: sudo fdisk -l Then I get: /dev/sda1 1 13 104391 de Dell Utility /dev/sda2 14 2805 22425601 5 Rozszerzona /dev/sda3 * 2805 41968 314572800 7 HPFS/NTFS /dev/sda4 41968 60802 151282688 7 HPFS/NTFS /dev/sda5 14 2445 19530752 83 Linux /dev/sda6 2445 2805 2893824 82 Linux swap / Solaris Next commands: sudo mount /dev/sda5 /mnt sudo mount --bind /dev /mnt/dev sudo mount --bind /proc /mnt/proc sudo chroot /mnt grub-install /dev/sda I get Installation finished. No error reported.. And when I start my machine I have old Ubuntu start screen to choose system. Ubuntu works well. But There are no Windows 8 option. But my primary problem is when I choose Windows 7 I have: error: no such device ... error: no such disk so I have no idea what can I do. I really need both systems to work. Any help would be appreciated.

    Read the article

  • Want to add a new domain to my postfix, but mails not delivered (mail look back to myself)

    - by user74850
    Hi everybody, My host relay is working but I was aksed to add a new domain (like external.example.com). I have added in main.cf the new fqdn in relay_domains relay_domains = $mydestination, example.com,example2.com, externe.example.com and in transport example.com smtp:[192.168.1.22] example2.com smtp:[192.168.1.22] external.example.com smtp:[192.168.1.22] Mails sent to users with example.com and example2.com domain are well delivered. But for mails to external.example.com i got this message Mar 17 16:47:52 relayhost postfix/smtp[11948]: 754E1876A01: to=<[email protected]>, relay=relayhost2.example.com[80.81.82.83]:25, delay=19555, delays=19525/0.01/30/0, dsn=4.4.6, status=deferred (mail for external.example.com loops back to myself) I read another Q/A about the same issue right here, but it's not helping me. Can you ?

    Read the article

  • Root partition full? CentOS

    - by Joao Heleno
    Hi! I'm running CentOS 5.4 and my / is full. I wanted to install gparted but in order to do that I must install Priorities and it's when I get an error saying / is full so I can't go forward. Here's some output: fdisk -l Disk /dev/sda: 250.0 GB, 250000000000 bytes 255 heads, 63 sectors/track, 30394 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sda1 * 1 2611 20972826 83 Linux /dev/sda2 2612 3251 5140800 82 Linux swap / Solaris /dev/sda3 3252 30394 218026147+ 83 Linux df Filesystem 1K-blocks Used Available Use% Mounted on /dev/sda1 20315812 19365152 0 100% / /dev/sda3 211196248 49228164 151066780 25% /home tmpfs 1552844 0 1552844 0% /dev/shm I'm not using LVM. Please advise. Thanks

    Read the article

  • Accessing second hard drive

    - by Jonathan
    Hi, So I recently installed Ubuntu 10.10 64-bit on my computer. I installed it on my 60gb SSD hard drive, and in the installation it never acknowledged the existence of my second hard drive. The hard drive that I keep all my files on, and which I want to make my home folder if I can, is a Western Digital Caviar Black 1TB SATA 6Gb/s 64MB cache (WD1002FAEX). I've read the following: https://help.ubuntu.com/community/Mount but honestly cannot work out how to access the hard drive from my Ubuntu installation. I did have Windows 7 64-bit prior to installing Ubuntu. I have backed up all the files on the hard drive, but if I could just access them straight off that would be super cool. Does anyone know how I can use the second hard drive? Thank you for your help EDIT: The following directories are currently in my /dev/ folder: ati/, block/, bsg/, bus/, char/, cpu/, isk/, input/, mapper/, net/, pktcdvd/, pts/, shm/, snd/, and usb/ EDIT: Result from sudo fdisk -l Disk /dev/sda: 60.0 GB, 60022480896 bytes 255 heads, 63 sectors/track, 7297 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000d2dfd Device Boot Start End Blocks Id System /dev/sda1 * 1 6994 56174592 83 Linux /dev/sda2 6994 7298 2438145 5 Extended /dev/sda5 6994 7298 2438144 82 Linux swap / Solaris

    Read the article

  • How do I install the EW-7318Ug wireless drivers?

    - by user69731
    I'm on Ubuntu 12.04 and I need to install & configure Internet connection. I want to use montor mode in Wireshark. After Ubuntu installation my wireless card was recognized but it doesn't connect to the Internet. Internal wireless card works well. What should I do? I'm new to Linux. PC:~$ ifconfig -a eth0 Link encap:Ethernet HWaddr 64:31:50:0f:d4:70 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:45 Base address:0x8000 eth1 Link encap:Ethernet HWaddr e0:2a:82:aa:2d:3e inet addr:192.168.0.101 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::e22a:82ff:feaa:2d3e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:20978 errors:0 dropped:0 overruns:0 frame:364651 TX packets:20949 errors:171 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:19299119 (19.2 MB) TX bytes:3024858 (3.0 MB) Interrupt:19 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4788 errors:0 dropped:0 overruns:0 frame:0 TX packets:4788 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:387017 (387.0 KB) TX bytes:387017 (387.0 KB) wlan1 Link encap:Ethernet HWaddr 00:1f:1f:44:c1:a4 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:10508 errors:0 dropped:0 overruns:0 frame:0 TX packets:6143 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:14831319 (14.8 MB) TX bytes:644606 (644.6 KB) PC:~$ iwconfig lo no wireless extensions. wlan1 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on eth1 IEEE 802.11 Access Point: Not-Associated Link Quality:5 Signal level:225 Noise level:162 Rx invalid nwid:0 invalid crypt:0 invalid misc:0 eth0 no wireless extensions.

    Read the article

  • StyleCop 4.7.34.0 has been released

    - by TATWORTH
    StyleCop 4.7.34.0 was released, today, 6/July at http://stylecop.codeplex.com/releases/view/79972Compatible with the Visual Studio 2012 RC (11.0.50522).Install order should be : VS2008VS2010VS2012 RCR#6.1.1 (for VS2010)R#7.0 (tested with daily build 7.0.83.281) (down load from http://confluence.jetbrains.net/display/ReSharper/ReSharper+7+EAP)StyleCop This version is now compatible with R# 5.1 (5.1.3000.12), R# 6.0 (6.0.2202.688), R# 6.1 (6.1.37.86), R# 6.1.1 (6.1.1000.82) and R# 7.0 (7.0.83.281).Here are the bug details for fixed in 4.7 and closed in 4.7 issues (over 100 issues fixed since 4.6)Here are the bug details for all issues since 4.3.3.0 that have been fixed and closed (over 450 fixes).Updated Release Notes are available hereOnline Rules documentation is available hereFixes for this release are:Update ReSharper 7.0 references to 7.0.83.281Fix for 7343. Inheritdoc was raising false positives for some partial classes. Added regression test data.Fix for 7351. Remove the correct blank lines for SA1512 on code cleanup.Fix for 7346. Insert documentation fully on cleanup and on bulb items.Ensure that the SuppressMessage bulbItem can calculate the correct element to insert at.Fix for 7352. Module level suppressmessages were not working.Spelling mistake.Add missing typenames to resource file.Spelling fixes.Remove obsolete files.

    Read the article

  • What does the fan speed sensor really report?

    - by T. Verron
    I have an overheating issue on my netbook (ASUS EeePC 1015PW), which I'm trying to troubleshoot. Using lm-sensors while overheating gave me this output : acpitz-virtual-0 Adapter: Virtual device temp1: +86.0°C (crit = +100.0°C) eeepc-isa-0000 Adapter: ISA adapter fan1: 4089 RPM coretemp-isa-0000 Adapter: ISA adapter Core 0: +82.0°C (crit = +100.0°C) Core 1: +80.0°C (crit = +100.0°C) But I can't hear the fan. So I enabled manual pwm controling and set the fan to full speed, and after a few minutes I got this output : acpitz-virtual-0 Adapter: Virtual device temp1: +65.0°C (crit = +100.0°C) eeepc-isa-0000 Adapter: ISA adapter fan1: 4016 RPM coretemp-isa-0000 Adapter: ISA adapter Core 0: +62.0°C (crit = +100.0°C) Core 1: +58.0°C (crit = +100.0°C) And this time I could hear the fan spinning. So there's quite obviously an issue with either fan control or fan monitoring. Hence the question : what kind of physical information does the fan sensor really report? Thank you PS. I should have added that the computer is a small, hard-to-disassemble netbook, so I can't and don't want to try experiments like "block the fan and see what the sensor reports".

    Read the article

  • Ubuntu 13.04 to 13.10: Filesystem check or mount failed

    - by SamHuckaby
    I attempted to upgrade from Ubuntu 13.04 to 13.10 today, and mid upgrade the system started flaking out, and eventually locked up entirely. I was forced to restart the computer, and am now unable to get the computer to boot up at all. When I boot currently, it takes me to the GRUB menu, and I can choose to boot normally, or boot in an older version. I have tried several things, which I list below, but no matter what, when I try to finish booting into Ubuntu, I receive the following error: Filesystem check or mount failed. A maintenance shell will now be started. CONTROL-D will terminate this shell and continue booting after re-trying filesystems. Any further errors will be ignored root@ubuntu-computername:~# I have fun fsck -f and everything appears correct, no errors are reported. and it passes all 5 checks. If I run fdisk -l then I get the following information: Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 4096 bytes / 4096 bytes Disk identifier: 0x00010824 Device Boot Start End Blocks Id System /dev/sda1 * 2048 608456703 304227328 83 Linux /dev/sda2 608458750 625141759 8341505 5 Extended Partition 2 does not start on physical sector boundary. /dev/sda5 608458752 625141759 8341504 82 Linux swap / Solaris Disk /dev/sdb: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x0fb4b7e8 Device Boot Start End Blocks Id System /dev/sdb1 8192 625139711 312565760 7 HPFS/NTFS/exFAT I am considering just installing a new OS on the other disk, that currently has nothing on it, and then just attempting to scrape my data off the old disk (thankfully I didn't encrypt the files). Really my question is this: Can I salvage this Ubuntu install, or should I give up and just reinstall?

    Read the article

  • "Enable Wireless" option is disabled in network settings

    - by silenTK
    I'm using Ubuntu 11.10 (dual booted with Windows 7) but I'm unable to access Internet wireless even though I can do so on Windows 7. The output for rfkill list all is given below: rfkill list all 0: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no The output for sudo lshw -C network *-network DISABLED is: description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth1 version: 01 serial: 11:11:11:11:11:11 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:16 memory:c2500000-c2503fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 05 serial: 22:22:22:22:22:22 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8105e-1.fw latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:42 ioport:3000(size=256) memory:c0404000-c0404fff memory:c0400000-c0403fff Broadcom STA wireless driver is installed, activated, and currently in use. My laptop is a HP-Pavilion-g6-1004tx. My hardware switch is on. Enable Wireless option is also disabled in network settings.

    Read the article

  • wireless is disabled by hardware lenovo 3000g430

    - by sudheer
    sir i have problem with my wifi switch sir please tell me solution for my problem (wifi is disabled by hardware). output of sudo lshw -C network is sudo] password for sudheer: *-network DISABLED description: Wireless interface product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:06:00.0 logical name: eth2 version: 01 serial: 00:21:00:72:3a:93 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11bg resources: irq:19 memory:f4700000-f4703fff *-network description: Ethernet interface product: NetLink BCM5906M Fast Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:07:00.0 logical name: eth0 version: 02 serial: 00:1e:68:ad:24:0b size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.121 duplex=full firmware=sb v3.04 ip=172.16.52.79 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:47 memory:f4600000-f460ffff output of iwconfig is lo no wireless extensions. eth2 IEEE 802.11 Access Point: Not-Associated Link Quality:5 Signal level:0 Noise level:0 Rx invalid nwid:0 invalid crypt:0 invalid misc:0 eth0 no wireless extensions. sudheer@sudheer:~$ sudo iwlistscanning sudo: iwlistscanning: command not found ***sudheer@sudheer:~$ sudo iwlist scanning*** lo Interface doesn't support scanning. eth2 Failed to read scan data : Invalid argument eth0 Interface doesn't support scanning.

    Read the article

  • SD Card only mounted after a reboot

    - by hattenn
    I have a Kingston 2GB MicroSD and I plug it in via an inconix MicroSD Adapter to the internal card reader of my Samsung N210 Netbook with Ubuntu 10.10, but it doesn't show up. Only if I reboot the system when the card's plugged in it shows up. Why does it need a reboot for mounting? sudo fdisk -l gives the output below. But I can only see the drive when I reboot the computer while the card's plugged. Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x9a5a7990 Device Boot Start End Blocks Id System /dev/sda1 1 1959 15728640 27 Unknown Partition 1 does not end on cylinder boundary. /dev/sda2 * 1959 1972 102400 7 HPFS/NTFS /dev/sda3 1972 18992 136718750 83 Linux /dev/sda4 18992 19458 3738625 5 Extended /dev/sda5 18992 19458 3738624 82 Linux swap / Solaris Disk /dev/sdb: 1973 MB, 1973420032 bytes 60 heads, 59 sectors/track, 1088 cylinders Units = cylinders of 3540 * 512 = 1812480 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdb1 1 1089 1927100+ 6 FAT16

    Read the article

  • Dell inspiron not finding Vodafone router

    - by Jeggy
    I have a "Dell inspiron 1564" and ubuntu doesn't find my friends router it works great at home, he has a vodafone router jeggy@jeggy-XPS:~$ sudo lshw -C network *-network description: Wireless interface product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: eth1 version: 01 serial: 78:e4:00:2a:d1:eb width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11bg resources: irq:17 memory:f0200000-f0203fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 02 serial: b8:ac:6f:67:32:52 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=N/A latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:3000(size=256) memory:f0410000-f0410fff memory:f0400000-f040ffff memory:f0420000-f043ffff *-network description: Ethernet interface physical id: 4 logical name: ham0 serial: 7a:79:05:ff:3e:ec size: 10Mbit/s capabilities: ethernet physical configuration: autonegotiation=off broadcast=yes driver=tun driverversion=1.6 duplex=full firmware=N/A ip=5.255.62.236 link=yes multicast=yes port=twisted pair speed=10Mbit/s

    Read the article

  • Unable to mount an LVM Hard-drive after upgrade

    - by Bruce Staples
    I imagine this is a basic gotcha ... but I can't see it. I have a system with 2(physical) harddrives. The boot system (/dev/sda) was running 10.04 & the second drive (/dev/sdb) was just a mounted filesystem. I did a clean load of Ubuntu 12.04 overwriting /dev/sda (not an upgrade) & now cannot mount the second drive. so I do not know what to enter it into the fstab ... I had expected to use: /dev/sdb /tera ext4 defaults 0 2 But even manual mounting fails (I also have tried various "-t" options on the off chance!) sudo mount -t ext4 /dev/sdb1 /tera mount: wrong fs type, bad option, bad superblock on /dev/sdb1, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so Output from disk queries indicate that it is a Linux LVM & a healthy disk still. sudo lshw -C disk *-disk:0 description: ATA Disk product: WDC WD5000AACS-0 vendor: Western Digital physical id: 0 bus info: scsi@2:0.0.0 logical name: /dev/sda version: 01.0 serial: WD-WCASU1401098 size: 465GiB (500GB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 signature=00015a55 *-disk:1 description: ATA Disk product: WDC WD10EADS-00L vendor: Western Digital physical id: 1 bus info: scsi@3:0.0.0 logical name: /dev/sdb version: 01.0 serial: WD-WCAU47836304 size: 931GiB (1TB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 sudo fdisk -l Disk /dev/sda: 500.1 GB, 500106780160 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976771055 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00015a55 Device Boot Start End Blocks Id System /dev/sda1 * 2048 972580863 486289408 83 Linux /dev/sda2 972582910 976769023 2093057 5 Extended /dev/sda5 972582912 976769023 2093056 82 Linux swap / Solaris Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdb1 1 1953525167 976762583+ 8e Linux LVM LVM doesn't appear to be an option for mount or fstab. ... and here's a Smart data Screenshot from Disk Utility.

    Read the article

  • There's IP but can't reach gateway

    - by icky
    I have just installed ubuntu 12.04 on my new laptop, and brought it back to home, but I found the wireless network does not work. Strangely, it has the correct ip, but can't connect to the gateway. ifconfig gives ip 192.168.64.36, with broadcast 192.168.79.255 and mask 255.255.240.0, this are all correct, the gateway is at 192.168.64.1 cat /etc/resolv.conf nameserver 192.168.64.1 nameserver 127.0.0.1 which i think it's also right. but when I ping 192.168.64.1, all packages are lost. Please help me with this, I really do not know what happened to my network settings. Huckle, Thank you for your reply ifconfig wlan0 Link encap:Ethernet Hwaddr 88:f9:af:2a:ca:1b inet addr:192.168.64.36 Bcast:192.168.79.255 Mask:255.255.240.0 inet6 addr: fe80::8a9f:faff:fea2/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:27 errors:0 dropped:0 overruns:0 frame:0 TX packets:376 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3950 TX byetes:60288 iwconfig wlan0 IEEE 802.11bgn ESSID:"Chiono" Mode:Managed Frequency:2.417 GHz Access Point: 82:54:99:94:6D:43 Bit Rate=13.5 Mb/s Tx-Power=13 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on Link Quality=70/70 Signal Level=-32 dBm Rx invalid nwid:0 Rx invalid crypt:0 RX invalid frag:0 Tx excessive retries: 9 Invalid misc:10 Missed beacon:0 route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 192.168.64.1 0.0.0.0 UG 0 0 0 wlan0 link-local * 255.255.0.0 U 1000 0 0 wlan0 192.168.64.0 * 255.255.240.0 U 2 0 0 0 wlan0 Thank you very much

    Read the article

  • Resolution changes when using switch

    - by Edward D
    So, the "real" resolution of my monitor is 1024x768. That's what I'd use on my docked Windows laptop, and what I'd use on my Xubuntu desktop connected directly. When I connect a switch, to switch between the two, however, the ubuntu machine's resolution changes. Everything's still proportional, and it still thinks it's doing 1024x768, but the icons and fonts appear larger. Not 800x600 larger, but still big. When I used Xubuntu Precise, I created an xorg.conf file to set a resolution of 1280x1024 which made it look the way it does without the switch ... as a workaround. When I upgraded to Trusty, I lost this. I tried to re-create it, but doesn't seem to load my file. Ideally, I'd like to correct the original problem, but I'd settle for being able to up the resolution. I searched for a while, and tried to do it, but I'm giving up ... please help me out. Controller: Intel Corporation 82915G/P/GV/GL/PL/910GL Memory Controller Hub (rev 04) Monitor: NEC MultiSync LCD 1850e http://www.necdisplay.com/documents/UserManuals/LCD1850E_manual.pdf OS: Xubuntu 14.04 Trusty /etc/X11/xorg.conf: # YOU CREATED THIS FILE # sudo leafpad /etc/X11/xorg.conf Section "Device" Identifier "Configured Video Device" EndSection Section "Monitor" Identifier "NEC LCD1850E" # I found Synchronization Range at: # http://www.necdisplay.com/documents/UserManuals/LCD1850E_manual.pdf HorizSync 31.0-82.0 VertRefresh 55.0-85.0 EndSection Section "Screen" Identifier "Default Screen" Monitor "NEC LCD1850E" Device "Configured Video Device" SubSection "Display" Depth 24 Modes "1280x1024" "1280x960" "1024x768" "800x600" "848x480" "640x480" EndSubSection EndSection

    Read the article

  • My D-Link Router is only allowing one connection

    - by Blaze
    My Router (Model: DI-624) is only allowing one wireless connection to one laptop. The other laptop is stuck hanging at connecting to the Internet I have the SSID set as "Pedro-Home" and is using a WPA PSK secured password. I have set the router using "Blaze-PC" while wired. Both Laptops critically need the Internet. > Dynamic DHCP Client List > > Host Name IP Address MAC > Address Expired Time > Blaze-PC 192.168.0.100 70-f1-a1-ff-39-a8 Apr/21/2011 17:49:14 > pedro 192.168.0.105 00-26-82-c8-47-25 Apr/21/2011 17:50:05 <<This computer isn't connecting.

    Read the article

  • UDF Partition reported full when it is not

    - by Capt.Nemo
    I was using these instructions to setup an external hard disk with udf. I have been able to setup a multi-partition system using those instructions, but I seem to have hit a wall, where the partition is reported as full while writing to the disk. Every other tool available to me reports it as free. Relevant lshw output Here's a screenshot showing the disk: Both the output of df and the file manager (caja) report the disk as free. Filesystem Size Used Avail Use% Mounted on /dev/sda9 9.0G 7.6G 910M 90% / udev 974M 12K 974M 1% /dev /dev/sda1 50G 47G 295M 100% /media/Data /dev/sda6 49G 41G 5.9G 88% /home /dev/sda2 155G 127G 29G 82% /media/Entertainment /dev/sda8 14G 13G 516M 96% /media/Stuff /dev/sdb2 120G 1.9G 112G 2% /media/3c887659-5676-4946-875b-b797be508ce7 /dev/sdb3 11G 2.6G 7.7G 25% /media/108b0a1d-fd1a-4f38-b1c6-4ad1a20e34a3 /dev/sdb1 802G 34G 768G 5% /media/disk I seem to have hit a wall near the 35GB mark. Despite being shown as 35gb/860gb used everywhere, the following happens on a write attempt: [2017][/media/Dory]$ echo D>>echo bash: echo: write error: No space left on device Writing byte by byte, the maximum I can take it to is 34719248K. The most weird part is that on mounting it Windows, Windows can write to the disk easily, and the writes are being read fine back in Ubuntu. However, the used-bytes remains at 34719248K in Ubuntu (It goes higher on Windows, however).

    Read the article

  • Copying unicode symbols from Firefox address bar as is

    - by sindikat
    Let's say I open a webpage with some Unicode characters, say, Cyrillic, in the address like this: http://ru.wikipedia.org/wiki/??????????????_?????????????? When I try to copy it from the address bar somewhere else, it becomes unreadable rubbish: http://ru.wikipedia.org/wiki/%D0%A4%D1%83%D0%BD%D0%BA%D1%86%D0%B8%D0%BE%D0%BD%D0%B0%D0%BB%D1%8C%D0%BD%D0%B0%D1%8F_%D0%B7%D0%B0%D0%BA%D1%80%D0%B5%D0%BF%D0%BB%D1%91%D0%BD%D0%BD%D0%BE%D1%81%D1%82%D1%8C I guess this is for compatibility. However for readability I want to copy it straight away with proper Unicode characters. What and how should I tweak to make that possible?

    Read the article

  • Accessing second hard drive

    - by Jonathan
    So I recently installed Ubuntu 10.10 64-bit on my computer. I installed it on my 60gb SSD hard drive, and in the installation it never acknowledged the existence of my second hard drive. The hard drive that I keep all my files on, and which I want to make my home folder if I can, is a Western Digital Caviar Black 1TB SATA 6Gb/s 64MB cache (WD1002FAEX). I've read the following: https://help.ubuntu.com/community/Mount but honestly cannot work out how to access the hard drive from my Ubuntu installation. I did have Windows 7 64-bit prior to installing Ubuntu. I have backed up all the files on the hard drive, but if I could just access them straight off that would be super cool. Does anyone know how I can use the second hard drive? Thank you for your help EDIT: The following directories are currently in my /dev/ folder: ati/, block/, bsg/, bus/, char/, cpu/, isk/, input/, mapper/, net/, pktcdvd/, pts/, shm/, snd/, and usb/ EDIT: Result from sudo fdisk -l Disk /dev/sda: 60.0 GB, 60022480896 bytes 255 heads, 63 sectors/track, 7297 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000d2dfd Device Boot Start End Blocks Id System /dev/sda1 * 1 6994 56174592 83 Linux /dev/sda2 6994 7298 2438145 5 Extended /dev/sda5 6994 7298 2438144 82 Linux swap / Solaris @djeykib So very close to fixing it.. unfortunately on the last command you gave it says this: $ sudo apt-get install linux-lts-backport-natty Reading package lists... Done Building dependency tree Reading state information... Done E: Unable to locate package linux-lts-backport-natty Checking on http://www.ubuntuupdates.org/ppas reveals that it is only available for 10.04. Looks like I'll have to unplug and re-plug hardware if I want it working still :(

    Read the article

  • How can I triple boot Xubuntu, Ubuntu and Windows?

    - by ag.restringere
    Triple Booting Xubuntu, Ubuntu and Windows I'm an avid Xubuntu (Ubuntu + XFCE) user but I also dual boot with Windows XP. I originally created 3 partitions and wanted to use the empty one as a storage volume but now I want to install Ubuntu 12.04 LTS (the one with Unity) to do advanced testing and packaging. Ideally I would love to keep these two totally separate as I had problems in the past with conflicts between Unity and XFCE. This way I could wipe the Ubuntu w/ Unity installation if there are problems and really mess around with it. My disk looks like this: /dev/sda1 -- Windows XP /dev/sda2 -- Disk /dev/sda: 200.0 GB, 200049647616 bytes 255 heads, 63 sectors/track, 24321 cylinders, total 390721968 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Device Boot Start End Blocks Id System /dev/sda1 * 63 78139454 39069696 7 HPFS/NTFS/exFAT /dev/sda2 78141440 156280831 39069696 83 Linux /dev/sda3 156282878 386533375 115125249 5 Extended /dev/sda4 386533376 390721535 2094080 82 Linux swap / Solaris /dev/sda5 156282880 386533375 115125248 83 Linux Keep each in it's own partition and totally separate and be able to select from each of the three systems from the GRUB boot menu... sda1 --- [Windows XP] sda2 --- [Ubuntu 12.04] "Unity" sda3(4,5) -- [Xubuntu 12.02] "Primary XFCE" What is the safest and easiest way to do this without messing my system up and requiring invasive activity?

    Read the article

  • Banshee gapless playback does not work when playing mp3s

    - by ComputerGuy505
    Even though I have gapless playback enabled in Banshee's settings menu, there is a very short pause between songs. This might be due to the fact that my hard drive's partitions seem wierd. fdisk -l produces this output: Disk /dev/sda: 750.2 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders, total 1465149168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x4a73c3cb Device Boot Start End Blocks Id System /dev/sda1 * 2048 409599 203776 7 HPFS/NTFS/exFAT /dev/sda2 409600 724153740 361872070+ 7 HPFS/NTFS/exFAT /dev/sda3 1456826368 1465145343 4159488 c W95 FAT32 (LBA) /dev/sda4 724154366 1456826367 366336001 5 Extended Partition 4 does not start on physical sector boundary. /dev/sda5 1440159744 1456826367 8333312 82 Linux swap / Solaris /dev/sda6 724154368 1440159743 358002688 83 Linux Partition table entries are not in disk order Playing mp3's from /dev/sda2 or /dev/sda6 produces this problem. I don't seem to have gapless playback on Rhythmbox or Clementine either, if those media players are supposed to have it. I'm not sure what other info to provide. This is just annoying to me. Thanks for any help.

    Read the article

< Previous Page | 17 18 19 20 21 22 23 24 25 26 27 28  | Next Page >