Search Results

Search found 937 results on 38 pages for 'lo sauer'.

Page 21/38 | < Previous Page | 17 18 19 20 21 22 23 24 25 26 27 28  | Next Page >

• OpenVPN and PPTP on XEN VPS

  - by amiv

  I have Debian based system (Ubuntu 11.10) on XEN VPS. I've installed OpenVPN and works great. I need to install PPTP too, so did it and clients can connect, but they have no internet on client side. If I connect to VPN over PPTP I can ping and access to only my VPS by its IP, but ony that. There's no "internet" on client side. It looks it's not DNS problems (I'm using 8.8.8.8) because I can't ping known IPs. I bet the solution is simple, but don't have any idea. Any guess? /etc/pptpd.conf option /etc/ppp/pptpd-options logwtmp localip 46.38.xx.xx remoteip 10.1.0.1-10 /etc/ppp/pptpd-options name pptpd refuse-pap refuse-chap refuse-mschap require-mschap-v2 require-mppe-128 ms-dns 8.8.8.8 ms-dns 8.8.4.4 proxyarp nodefaultroute lock nobsdcomp /etc/ppp/ip-up [...] ifconfig ppp0 mtu 1400 /etc/sysctl.conf [...] net.ipv4.ip_forward=1 Command which I run: iptables -t nat -A POSTROUTING -j SNAT --to-source 46.38.xx.xx (IP of my VPS) The client can connect, first one gets IP 10.1.0.1 and DNS from Google. I bet it's iptables problem, am I right? I'm iptables noob and I don't have idea what's wrong. And here's the ifconfig and route command before client connect via PPTP: root@vps3780:~# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default xx.xx.tel.ru 0.0.0.0 UG 100 0 0 eth0 10.8.0.0 10.8.0.2 255.255.255.0 UG 0 0 0 tun0 10.8.0.2 * 255.255.255.255 UH 0 0 0 tun0 46.38.xx.0 * 255.255.255.0 U 0 0 0 eth0 root@vps3780:~# ifconfig eth0 Link encap:Ethernet HWaddr 00:16:3e:56:xx:xx inet addr:46.38.xx.xx Bcast:0.0.0.0 Mask:255.255.255.0 inet6 addr: fe80::216:xx:xx:dfb6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:22671 errors:0 dropped:81 overruns:0 frame:0 TX packets:2266 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1813358 (1.8 MB) TX bytes:667626 (667.6 KB) Interrupt:24 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:100 errors:0 dropped:0 overruns:0 frame:0 TX packets:100 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:10778 (10.7 KB) TX bytes:10778 (10.7 KB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.8.0.1 P-t-P:10.8.0.2 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:602 errors:0 dropped:0 overruns:0 frame:0 TX packets:612 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:90850 (90.8 KB) TX bytes:418904 (418.9 KB) And here's the ifconfig and route command after client connect via PPTP: root@vps3780:~# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default xx.xx.tel.ru 0.0.0.0 UG 100 0 0 eth0 10.1.0.1 * 255.255.255.255 UH 0 0 0 ppp0 10.8.0.0 10.8.0.2 255.255.255.0 UG 0 0 0 tun0 10.8.0.2 * 255.255.255.255 UH 0 0 0 tun0 46.38.xx.0 * 255.255.255.0 U 0 0 0 eth0 root@vps3780:~# ifconfig eth0 Link encap:Ethernet HWaddr 00:16:3e:56:xx:xx inet addr:46.38.xx.xx Bcast:0.0.0.0 Mask:255.255.255.0 inet6 addr: fe80::216:xx:xx:dfb6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:22989 errors:0 dropped:82 overruns:0 frame:0 TX packets:2352 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1841310 (1.8 MB) TX bytes:678456 (678.4 KB) Interrupt:24 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:112 errors:0 dropped:0 overruns:0 frame:0 TX packets:112 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:12102 (12.1 KB) TX bytes:12102 (12.1 KB) ppp0 Link encap:Point-to-Point Protocol inet addr:46.38.xx.xx P-t-P:10.1.0.1 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1400 Metric:1 RX packets:66 errors:0 dropped:0 overruns:0 frame:0 TX packets:15 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:10028 (10.0 KB) TX bytes:660 (660.0 B) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.8.0.1 P-t-P:10.8.0.2 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:602 errors:0 dropped:0 overruns:0 frame:0 TX packets:612 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:90850 (90.8 KB) TX bytes:418904 (418.9 KB) And ugly iptables --list output: root@vps3780:~# iptables --list Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT all -- 10.8.0.0/24 anywhere REJECT all -- anywhere anywhere reject-with icmp-port-unreachable ACCEPT all -- 10.1.0.0/24 anywhere ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT all -- 10.1.0.0/24 anywhere REJECT all -- anywhere anywhere reject-with icmp-port-unreachable ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT all -- 10.8.0.0/24 anywhere REJECT all -- anywhere anywhere reject-with icmp-port-unreachable And ugly iptables -t nat -L output: root@vps3780:~# iptables -t nat -L Chain PREROUTING (policy ACCEPT) target prot opt source destination Chain INPUT (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination Chain POSTROUTING (policy ACCEPT) target prot opt source destination SNAT all -- 10.8.0.0/24 anywhere to:46.38.xx.xx MASQUERADE all -- 10.1.0.0/24 anywhere SNAT all -- 10.1.0.0/24 anywhere to:46.38.xx.xx SNAT all -- 10.8.0.0/24 anywhere to:46.38.xx.xx SNAT all -- 10.1.0.0/24 anywhere to:46.38.xx.xx MASQUERADE all -- anywhere anywhere SNAT all -- anywhere anywhere to:46.38.xx.xx SNAT all -- 10.8.0.0/24 anywhere to:46.38.xx.xx MASQUERADE all -- anywhere anywhere MASQUERADE all -- 10.1.0.0/24 anywhere MASQUERADE all -- anywhere anywhere MASQUERADE all -- 10.1.0.0/24 anywhere As I said - OpenVPN works very good. 10.8.0.0/24 for OpenVPN (on tun0). PPTP won't work. 10.1.0.0/24 for PPTP (on ppp0). Clients can connect, but they haven't "internet". Any suggestions will be appreciated. Second whole day fighting with no results. EDIT: iptables -t filter -F - it resolved my problem :-)

  Read the article

• assign auto static ip on ubuntu 10.04

  - by ronakin

  I'm trying to set auto static ip. I've set the content of /etc/network/interfaces to be: auto lo auto eth0 iface eth0 inet static address 192.168.1.2 netmask 255.255.255.0 gateway 192.168.1.1. and /etc/resolv.conf to be: nameserver 192.168.1.1. It seems that the ip address have set successfully. However, when I plug out the lan cable and then plug it back, the ip address is not set. How can I make it automatically set the static ip when the lan cable is connected?

  Read the article

• Can I ping via an arbitrary interface of a DD-WRT system?

  - by bytebuster

  There's a Linksys WRT54GL router with DD-WRT firmware (v23SP2). The network has a simple dual-WAN configuration (standby mode, switching by a script): ~ # ip route 192.168.3.0/24 dev br0 proto kernel scope link src 192.168.3.1 192.168.2.0/24 dev vlan2 proto kernel scope link src 192.168.2.2 192.168.1.0/24 dev vlan1 proto kernel scope link src 192.168.1.67 127.0.0.0/8 dev lo scope link default via 192.168.2.1 dev vlan2 I'm trying to ping a certain server arbitrary via vlan1 or vlan2. What I tried, as suggested here: ping -I vlan2 <address> ping 192.168.2.1 <address> In both cases ping simply exits with no error messages. Also, ping ignores many other parameters, again, by exiting silently. I failed to find any references that DD-WRT has a limited version of ping whatsoever. I also don't think it can be a permissions issue as mentioned here since the only user with DD-WRT is root. What's wrong?

  Read the article

• Not able to connect to internet in RHEL 5

  - by chankey007

  I just installed red hat enterprise 5 in my laptop and on desktop both. In desktop it is working fine but in laptop it is not showing the eth device. (I tried ifconfig only lo is there). I tried ifup eth0 still nothing happened. The network service in /etc/sysconfig/network-scripts/ifcfg-eth0 and in /etc/sysconfig/network are enable. I had ubuntu in my laptop before and I faced same problem with that too. Is there any problem with my laptop? I have my system on dual boot and in win7 networking is running fine. I am not able to connect to the internet only, other devices are working fine. System conf: Sony vaio E series. 3 GB RAM, intel core i3 2.13 GHZ.

  Read the article

• Not able to connect to internet in RHEL 5

  - by chankey007

  I just installed red hat enterprise 5 in my laptop and on desktop both. In desktop it is working fine but in laptop it is not showing the eth device. (I tried ifconfig only lo is there). I tried ifup eth0 still nothing happened. The network service in /etc/sysconfig/network-scripts/ifcfg-eth0 and in /etc/sysconfig/network are enable. I had ubuntu in my laptop before and I faced same problem with that too. Is there any problem with my laptop? I have my system on dual boot and in win7 networking is running fine. I am not able to connect to the internet only, other devices are working fine. System conf: Sony vaio E series. 3 GB RAM, intel core i3 2.13 GHZ.

  Read the article

• iptables ACCEPT policy

  - by kamae

  In Redhat EL 6, iptables INPUT policy is ACCEPT but INPUT chain has REJECT entry in the end. /etc/syconfig/iptables is as below: *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT -A INPUT -p icmp -j ACCEPT -A INPUT -i lo -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 22 -j ACCEPT -A INPUT -j REJECT --reject-with icmp-host-prohibited -A FORWARD -j REJECT --reject-with icmp-host-prohibited COMMIT Do you know why the policy is ACCEPT not DROP? I think setting DROP policy is safer than ACCEPT in case to make mistake in the chain. Actually the policy is not applied to any packet: # iptables -L -v Chain INPUT (policy ACCEPT 0 packets, 0 bytes)

  Read the article

• Is there a software that can index the contents of the registry for quick lookups?

  - by Benoit

  Searching in the Windows registry can be ve------ry------ lo----ng. Is there some tool available that can index the contents of the whole registry, or contents of a single hive, such that fast lookups are available? (for example generating some SQLite database with FTS3 or FTS4 enabled for full text search) Thank you. PS. I don't want RegScanner or tools that perform a new, linear search every time. I want an indexer, with which then a search can be instantaneous. See question comments.

  Read the article

• Route eth0 to internet traffic and eth1 to local traffic

  - by Romain Caire

  How can I route all my internet traffic on eth0 (everything except 192.168.1.0/24) and route my local traffic through eth1 (192.168.1.0)? Here is my attempt : # Flush ALL THE THINGS. ip route flush table main # Restore the main table. I flushed it because OpenVPN does weird things to it. ip route add 127.0.0.0/8 via 127.0.0.1 dev lo ip route add 0.0.0.0/0 via 164.67.195.1 ip route add 192.168.1.0/24 via 192.168.1.1 ip route flush cache

  Read the article

• Ubuntu cannot access internet, LAN is fine

  - by Kevin Southworth

  I have an Ubuntu 8.04 LTS server that is directly connected to our Comcast Business Gateway modem and I have configured it with 1 of our 5 allotted Static IPs. My other machines on our LAN can connect to this server (via ssh, web, ping, etc.) but I cannot access this server from outside our network, and this machine cannot get out to the internet either (ping google.com fails with unknown host). Here is my /etc/networking/interfaces file: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 173.162.54.19 netmask 255.255.255.248 broadcast 173.162.54.23 gateway 173.162.54.22 and my /etc/resolv.conf: nameserver 68.87.77.130 nameserver 68.87.72.130 output from sudo route -n: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 173.162.54.16 0.0.0.0 255.255.255.248 U 0 0 0 eth0 0.0.0.0 173.162.54.22 0.0.0.0 UG 100 0 0 eth0 I have a Windows 2008 machine with an almost identical Static IP, static DNS setup and it works correctly, can access it within the LAN and also from public internet, the Windows machine and the Ubuntu machine are both directly connected to the Comcast Business Gateway. I have tried rebooting Ubuntu, rebooting my Comcast modem, but nothing seems to make it work. I'm an Ubuntu noob, is there some other config I need to apply to make this work? UPDATE: Yes I am able to ping my default gateway 173.162.54.22 output of iptables --list -n: Chain INPUT (policy DROP) target prot opt source destination ufw-before-input all -- 0.0.0.0/0 0.0.0.0/0 ufw-after-input all -- 0.0.0.0/0 0.0.0.0/0 Chain FORWARD (policy DROP) target prot opt source destination ufw-before-forward all -- 0.0.0.0/0 0.0.0.0/0 ufw-after-forward all -- 0.0.0.0/0 0.0.0.0/0 Chain OUTPUT (policy ACCEPT) target prot opt source destination ufw-before-output all -- 0.0.0.0/0 0.0.0.0/0 ufw-after-output all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-after-forward (1 references) target prot opt source destination LOG all -- 0.0.0.0/0 0.0.0.0/0 limit: avg 3/min burst 10 LOG flags 0 level 4 prefix `[UFW BLOCK FORWARD]: ' RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-after-input (1 references) target prot opt source destination RETURN udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:137 RETURN udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:138 RETURN tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:139 RETURN tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:445 RETURN udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:67 RETURN udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:68 LOG all -- 0.0.0.0/0 0.0.0.0/0 limit: avg 3/min burst 10 LOG flags 0 level 4 prefix `[UFW BLOCK INPUT]: ' RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-after-output (1 references) target prot opt source destination RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-before-forward (1 references) target prot opt source destination ufw-user-forward all -- 0.0.0.0/0 0.0.0.0/0 RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-before-input (1 references) target prot opt source destination ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 ctstate RELATED,ESTABLISHED DROP all -- 0.0.0.0/0 0.0.0.0/0 ctstate INVALID ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 3 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 4 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 11 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 12 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 8 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp spt:67 dpt:68 ufw-not-local all -- 0.0.0.0/0 0.0.0.0/0 ACCEPT all -- 224.0.0.0/4 0.0.0.0/0 ACCEPT all -- 0.0.0.0/0 224.0.0.0/4 ufw-user-input all -- 0.0.0.0/0 0.0.0.0/0 RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-before-output (1 references) target prot opt source destination ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW,RELATED,ESTABLISHED ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 state NEW,RELATED,ESTABLISHED ufw-user-output all -- 0.0.0.0/0 0.0.0.0/0 RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-not-local (1 references) target prot opt source destination RETURN all -- 0.0.0.0/0 0.0.0.0/0 ADDRTYPE match dst-type LOCAL RETURN all -- 0.0.0.0/0 0.0.0.0/0 ADDRTYPE match dst-type MULTICAST RETURN all -- 0.0.0.0/0 0.0.0.0/0 ADDRTYPE match dst-type BROADCAST LOG all -- 0.0.0.0/0 0.0.0.0/0 limit: avg 3/min burst 10 LOG flags 0 level 4 prefix `[UFW BLOCK NOT-TO-ME]: ' DROP all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-user-forward (1 references) target prot opt source destination RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-user-input (1 references) target prot opt source destination ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:80 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:22 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:22 RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-user-output (1 references) target prot opt source destination RETURN all -- 0.0.0.0/0 0.0.0.0/0

  Read the article

• Can I ping via an arbitrary interface of a DD-WRT system? [migrated]

  - by bytebuster

  There's a Linksys WRT54GL router with DD-WRT firmware (v23SP2). The network has a simple dual-WAN configuration (standby mode, switching by a script): ~ # ip route 192.168.3.0/24 dev br0 proto kernel scope link src 192.168.3.1 192.168.2.0/24 dev vlan2 proto kernel scope link src 192.168.2.2 192.168.1.0/24 dev vlan1 proto kernel scope link src 192.168.1.67 127.0.0.0/8 dev lo scope link default via 192.168.2.1 dev vlan2 I'm trying to ping a certain server arbitrary via vlan1 or vlan2. What I tried, as suggested here: ping -I vlan2 <address> ping 192.168.2.1 <address> In both cases ping simply exits with no error messages. Also, ping ignores many other parameters, again, by exiting silently. I failed to find any references that DD-WRT has a limited version of ping whatsoever. I also don't think it can be a permissions issue as mentioned here since the only user with DD-WRT is root. What's wrong?

  Read the article

• Why is my ethernet interface in promiscuous mode

  - by nhed

  I read that seeing a flag of M in netstat -i is the way to tell which of your interfaces is in promiscuous mode I run it and I see that eth1 is in promiscuous mode $ netstat -i Kernel Interface table Iface MTU Met RX-OK RX-ERR RX-DRP RX-OVR TX-OK TX-ERR TX-DRP TX-OVR Flg eth1 1500 0 1770161198 0 0 0 57446481 0 0 0 BMRU lo 16436 0 97501566 0 0 0 97501566 0 0 0 LRU This seems to be the case on all the machines I checked (All Centos6.0, both virtual and physical), any idea why ethernet devices would be in such a mode unless someone was running any pcap based app (sudo lsof | grep pcap shows nothing)? I did not see any mention of promiscuous in any of the config files (sudo grep -r promis /etc) Any ideas what puts the interface into that mode and why? p.s. most of the posts I see seem to be security related, this is not that

  Read the article

• Firewall still blocking port 53 despite listing otherwise?

  - by Tom

  I have 3 nodes with virtually the same iptables rules loaded from a bash script, but one particular node is blocking traffic on port 53 despite listing it's accepting it: $ iptables --list -v Chain INPUT (policy DROP 8886 packets, 657K bytes) pkts bytes target prot opt in out source destination 0 0 ACCEPT all -- lo any anywhere anywhere 2 122 ACCEPT icmp -- any any anywhere anywhere icmp echo-request 20738 5600K ACCEPT all -- any any anywhere anywhere state RELATED,ESTABLISHED 0 0 ACCEPT tcp -- eth1 any anywhere node1.com multiport dports http,smtp 0 0 ACCEPT udp -- eth1 any anywhere ns.node1.com udp dpt:domain 0 0 ACCEPT tcp -- eth1 any anywhere ns.node1.com tcp dpt:domain 0 0 ACCEPT all -- eth0 any node2.backend anywhere 21 1260 ACCEPT all -- eth0 any node3.backend anywhere 0 0 ACCEPT all -- eth0 any node4.backend anywhere Chain FORWARD (policy DROP 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 15804 packets, 26M bytes) pkts bytes target prot opt in out source destination nmap -sV -p 53 ns.node1.com // From remote server Starting Nmap 4.11 ( http://www.insecure.org/nmap/ ) at 2011-02-24 11:44 EST Interesting ports on ns.node1.com (1.2.3.4): PORT STATE SERVICE VERSION 53/tcp filtered domain Nmap finished: 1 IP address (1 host up) scanned in 0.336 seconds Any ideas? Thanks

  Read the article

• OpenVPN IPv6 over IPv4 tunnel

  - by user66779

  Today I installed OpenVPN 2.3rc2 on both my windows 7 client machine and centos 6 server. This new version of OpenVPN provides full compatibility for IPv6. The Problem: I am currently able to connect to the server (through the IPv4 tunnel) and ping the IPv6 address which is assigned to my client and I can also ping the tun0 interface on the server. However, I cannot browse to any IPv6 websites. My vps provider has given me this: 2607:f840:0044:0022:0000:0000:0000:0000/64 is routed to this server (2607:f840:0:3f:0:0:0:eda). This is ifconfig after setup with OpenVPN running: eth0 Link encap:Ethernet HWaddr 00:16:3E:12:77:54 inet addr:208.111.39.160 Bcast:208.111.39.255 Mask:255.255.255.0 inet6 addr: 2607:f740:0:3f::eda/64 Scope:Global inet6 addr: fe80::216:3eff:fe12:7754/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2317253 errors:0 dropped:7263 overruns:0 frame:0 TX packets:1977414 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1696120096 (1.5 GiB) TX bytes:1735352992 (1.6 GiB) Interrupt:29 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.8.0.1 P-t-P:10.8.0.2 Mask:255.255.255.255 inet6 addr: 2607:f740:44:22::1/64 Scope:Global UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:739567 errors:0 dropped:0 overruns:0 frame:0 TX packets:1218240 errors:0 dropped:1542 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:46512557 (44.3 MiB) TX bytes:1559930874 (1.4 GiB) So OpenVPN is sucessfully creating a tun0 interface and assigning clients IPv6 addresses using 2607:f840:44:22::/64. The first client to connect is getting 2607:f840:44:22::1000 and the second 2607:f840:44:22::1001, and so on... plus 1 each time. After connecting as the first client, I can ping from my windows client machine 2607:f740:44:22::1 and 2607:f740:44:22::1000. However, I have no access to IPv6 websites. I believe the problem is that the tun0 IPv6 addressees are not being forwarded to the eth0 interface. This is the firewall running on the server: #!/bin/sh # # iptables configuration script # # Flush all current rules from iptables # iptables -F iptables -t nat -F # # Allow SSH connections on tcp port 22 # iptables -A INPUT -i eth0 -p tcp --dport 22 -j ACCEPT iptables -A OUTPUT -o eth0 -p tcp --sport 22 -j ACCEPT # # Set access for localhost # iptables -A INPUT -i lo -j ACCEPT # # Accept connections on 1195 for vpn access from client # iptables -A INPUT -i eth0 -p udp --dport 1195 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p udp --sport 1195 -m state --state ESTABLISHED -j ACCEPT # # Apply forwarding for OpenVPN Tunneling # iptables -A FORWARD -m state --state RELATED,ESTABLISHED -j ACCEPT iptables -A FORWARD -s 10.8.0.0/24 -j ACCEPT iptables -t nat -A POSTROUTING -o eth0 -j SNAT --to 209.111.39.160 iptables -A FORWARD -j REJECT # # Enable forwarding # echo 1 > /proc/sys/net/ipv4/ip_forward # # Set default policies for INPUT, FORWARD and OUTPUT chains # iptables -P INPUT ACCEPT iptables -P FORWARD ACCEPT iptables -P OUTPUT ACCEPT # # IPv6 # IP6TABLES=/sbin/ip6tables $IP6TABLES -F INPUT $IP6TABLES -F FORWARD $IP6TABLES -F OUTPUT echo -n "1" >/proc/sys/net/ipv6/conf/all/forwarding echo -n "1" >/proc/sys/net/ipv6/conf/all/proxy_ndp echo -n "0" >/proc/sys/net/ipv6/conf/all/autoconf echo -n "0" >/proc/sys/net/ipv6/conf/all/accept_ra $IP6TABLES -A INPUT -i eth0 -m state --state ESTABLISHED,RELATED -j ACCEPT $IP6TABLES -A INPUT -i eth0 -p tcp --dport 22 -j ACCEPT $IP6TABLES -A INPUT -i eth0 -p icmpv6 -j ACCEPT $IP6TABLES -P INPUT ACCEPT $IP6TABLES -P FORWARD ACCEPT $IP6TABLES -P OUTPUT ACCEPT Server.conf: server-ipv6 2607:f840:44:22::/64 server 10.8.0.0 255.255.255.0 port 1195 proto udp dev tun ca ca.crt cert server.crt key server.key dh dh2048.pem ifconfig-pool-persist ipp.txt push "redirect-gateway def1 bypass-dhcp" push "dhcp-option DNS 208.67.222.222" push "dhcp-option DNS 208.67.220.220" keepalive 10 60 tls-auth ta.key 0 cipher AES-256-CBC comp-lzo user nobody group nobody persist-key persist-tun status openvpn-status.log log-append openvpn.log verb 5 Client.conf: client dev tun nobind keepalive 10 60 hand-window 15 remote 209.111.39.160 1195 udp persist-key persist-tun ca ca.crt key client1.key cert client1.crt remote-cert-tls server tls-auth ta.key 1 comp-lzo verb 3 cipher AES-256-CBC I'm not sure where I am going wrong, it could be the firewall, or something missing from server or client.conf. This version of OpenVPN was only released yesterday, and there's little info on the internet about how to setup an IPv6 over IPv4 vpn tunnel. I've read the manual for this new version of OpenVPN (parts pertaining to IPv6) and it provides very little info too. Thanks for any help.

  Read the article

• OpenVZ multiple networks on CTs

  - by user6733

  I have Hardware Node (HN) which has 2 physical interfaces (eth0, eth1). I'm playing with OpenVZ and want to let my containers (CTs) have access to both of those interfaces. I'm using basic configuration - venet. CTs are fine to access eth0 (public interface). But I can't get CTs to get access to eth1 (private network). I tried: # on HN vzctl set 101 --ipadd 192.168.1.101 --save vzctl enter 101 ping 192.168.1.2 # no response here ifconfig # on CT returns lo (127.0.0.1), venet0 (127.0.0.1), venet0:0 (95.168.xxx.xxx), venet0:1 (192.168.1.101) I believe that the main problem is that all packets flows through eth0 on HN (figured out using tcpdump). So the problem might be in routes on HN. Or is my logic here all wrong? I just need access to both interfaces (networks) on HN from CTs. Nothing complicated.

  Read the article

• vmware player - ubuntu can resolve hostname but ping fails

  - by recursive_acronym

  Using VMware players on Windows 7 with a Ubuntu 10.04 guest. When I ping it resolves the ip address but the ping fails. Hopefully this is a local issue as I don't have access to any of the network equipment (routers, etc). vmware tools is installed. Is there any other information I can provide to help resolve this? eth0 Link encap:Ethernet HWaddr 00:0c:29:83:4f:c0 inet addr:192.168.163.129 Bcast:192.168.163.255 Mask:255.255.255.0 inet6 addr: fe80::20c:29ff:fe83:4fc0/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:475 errors:0 dropped:0 overruns:0 frame:0 TX packets:179 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:50006 (50.0 KB) TX bytes:16701 (16.7 KB) Interrupt:19 Base address:0x2024 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:480 (480.0 B) TX bytes:480 (480.0 B)

  Read the article

• How to know my wireless card has injection enabled?

  - by shrimpy

  I am playing around with aircrack. And was trying to see whether my wireless card on my laptop can pass the injection test And I end up seeing the following... does it mean my wireless card is not able to run aircrack? root@myubuntu:/home/myubuntu# iwconfig lo no wireless extensions. eth0 no wireless extensions. eth1 IEEE 802.11bg ESSID:"" Nickname:"" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Bit Rate:54 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=5/5 Signal level=0 dBm Noise level=-57 dBm Rx invalid nwid:0 Rx invalid crypt:781 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 root@myubuntu:/home/myubuntu# aireplay-ng -9 eth1 ioctl(SIOCSIWMODE) failed: Invalid argument ARP linktype is set to 1 (Ethernet) - expected ARPHRD_IEEE80211, ARPHRD_IEEE80211_FULL or ARPHRD_IEEE80211_PRISM instead. Make sure RFMON is enabled: run 'airmon-ng start eth1 <#>' Sysfs injection support was not found either. root@myubuntu:/home/myubuntu#

  Read the article

• Accessing mySQL from two ports: Problems with iptables

  - by marekventur

  Hi! I'm trying to make my mySQL-server (running on Ubuntu) listen on port 3306 and 110, because I would like to access it from a network with very few open ports. So far I've found this answer telling me to do iptables -t nat -A PREROUTING -i eth0 -p tcp --dport 110 -j REDIRECT --to-port 3306 but all I got is: # mysql -h mydomain.com -P 3306 -u username --password=xyz Welcome to the MySQL monitor. Commands end with ; or \g. Your MySQL connection id is 68863 Server version: 5.0.75-0ubuntu10.5 (Ubuntu) Type 'help;' or '\h' for help. Type '\c' to clear the buffer. mysql> exit Bye # mysql -h mydomain.com -P 110 -u username --password=xyz ERROR 2003 (HY000): Can't connect to MySQL server on 'mydomain.com' (111) I'm not an expert with iptables, so I not sure where to look for the problem. I'm googling around for quite some time, but haven't found anything to help me yet. This is what iptable tells me: # iptables -t nat -L -n -v Chain PREROUTING (policy ACCEPT 32M packets, 1674M bytes) pkts bytes target prot opt in out source destination 0 0 REDIRECT tcp -- eth0 * 0.0.0.0/0 0.0.0.0/0 tcp dpt:110 redir ports 3306 Chain POSTROUTING (policy ACCEPT 855K packets, 55M bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 837K packets, 54M bytes) pkts bytes target prot opt in out source destination # iptables -L -n -v Chain INPUT (policy DROP 7 packets, 340 bytes) pkts bytes target prot opt in out source destination 107K 5390K LOG all -- * * 0.0.0.0/0 0.0.0.0/0 state INVALID limit: avg 2/sec burst 5 LOG flags 0 level 4 prefix `INPUT INVALID ' 131K 6614K DROP all -- * * 0.0.0.0/0 0.0.0.0/0 state INVALID 0 0 MY_DROP tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp flags:0x3F/0x00 0 0 MY_DROP tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp flags:0x03/0x03 0 0 MY_DROP tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp flags:0x06/0x06 0 0 MY_DROP tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp flags:0x05/0x05 0 0 MY_DROP tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp flags:0x11/0x01 0 0 MY_DROP tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp flags:0x18/0x08 0 0 MY_DROP tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp flags:0x30/0x20 6948K 12G ACCEPT all -- lo * 0.0.0.0/0 0.0.0.0/0 151M 34G ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 32M 1666M ACCEPT tcp -- venet0 * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:80 1833 106K ACCEPT tcp -- venet0 * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:443 603 29392 ACCEPT tcp -- venet0 * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:25 1 60 ACCEPT tcp -- venet0 * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:465 24 1180 ACCEPT tcp -- venet0 * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:110 1 60 ACCEPT tcp -- venet0 * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:995 7919 400K ACCEPT tcp -- venet0 * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:143 1 60 ACCEPT tcp -- venet0 * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:993 0 0 ACCEPT tcp -- venet0 * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:119 1 60 ACCEPT tcp -- venet0 * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:53 7 517 ACCEPT udp -- venet0 * 0.0.0.0/0 0.0.0.0/0 state NEW udp dpt:53 1110 65364 ACCEPT tcp -- venet0 * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:21 139K 8313K ACCEPT tcp -- venet0 * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:22 10176 499K ACCEPT tcp -- venet0 * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:3306 2 80 ACCEPT udp -- venet0 * 0.0.0.0/0 0.0.0.0/0 state NEW udp dpt:123 0 0 ACCEPT tcp -- venet0 * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:6060 4 176 ACCEPT tcp -- venet0 * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:6667 20987 1179K MY_REJECT all -- * * 0.0.0.0/0 0.0.0.0/0 Chain FORWARD (policy DROP 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy DROP 0 packets, 0 bytes) pkts bytes target prot opt in out source destination 2159 284K LOG all -- * * 0.0.0.0/0 0.0.0.0/0 state INVALID limit: avg 2/sec burst 5 LOG flags 0 level 4 prefix `OUTPUT INVALID ' 2630 304K DROP all -- * * 0.0.0.0/0 0.0.0.0/0 state INVALID 6948K 12G ACCEPT all -- * lo 0.0.0.0/0 0.0.0.0/0 181M 34G ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state NEW,RELATED,ESTABLISHED 0 0 MY_REJECT all -- * * 0.0.0.0/0 0.0.0.0/0 Chain MY_DROP (7 references) pkts bytes target prot opt in out source destination 0 0 LOG all -- * * 0.0.0.0/0 0.0.0.0/0 limit: avg 2/sec burst 5 LOG flags 0 level 4 prefix `PORTSCAN DROP ' 0 0 DROP all -- * * 0.0.0.0/0 0.0.0.0/0 Chain MY_REJECT (2 references) pkts bytes target prot opt in out source destination 13806 652K LOG tcp -- * * 0.0.0.0/0 0.0.0.0/0 limit: avg 2/sec burst 5 LOG flags 0 level 4 prefix `REJECT TCP ' 18171 830K REJECT tcp -- * * 0.0.0.0/0 0.0.0.0/0 reject-with tcp-reset 912 242K LOG udp -- * * 0.0.0.0/0 0.0.0.0/0 limit: avg 2/sec burst 5 LOG flags 0 level 4 prefix `REJECT UDP ' 912 242K REJECT udp -- * * 0.0.0.0/0 0.0.0.0/0 reject-with icmp-port-unreachable 1904 107K LOG icmp -- * * 0.0.0.0/0 0.0.0.0/0 limit: avg 2/sec burst 5 LOG flags 0 level 4 prefix `DROP ICMP ' 1904 107K DROP icmp -- * * 0.0.0.0/0 0.0.0.0/0 0 0 LOG all -- * * 0.0.0.0/0 0.0.0.0/0 limit: avg 2/sec burst 5 LOG flags 0 level 4 prefix `REJECT OTHER ' 0 0 REJECT all -- * * 0.0.0.0/0 0.0.0.0/0 reject-with icmp-proto-unreachable Is there anyone who can give ma a hint where to look for the problem? Thank you!

  Read the article

• Samba / smbd on Centos 6.5

  - by Satalink

  I've installed Samba4 and have the smb.conf file as follows: [global] workgroup = WORKGROUP server string = Samba Server realm = REXIALO.COM netbios name = REXIALO.COM security = user map to guest = Bad Password bind interfaces only = no interfaces = lo venet0 log file = /var/log/samba/samba.log max log size = 1000 [webroot] path = /usr/local/apache/htdocs comment = Example.com webroot directory read only = No I can connect from the same server with smbclient. Localhost: # smbclient -L localhost -U root Domain=[WORKGROUP] OS=[Unix] Server=[Samba 4.1.11] Sharename Type Comment --------- ---- ------- webroot Disk RexiAlo webroot directory IPC$ IPC IPC Service (RexiAlo Samba Server) Domain=[WORKGROUP] OS=[Unix] Server=[Samba 4.1.11] Server Comment --------- ------- Workgroup Master --------- -------Enter root's password: network: # smbclient -L rexialo.com -U Domain=[WORKGROUP] OS=[Unix] Server=[Samba 4.1.11] Sharename Type Comment --------- ---- ------- webroot Disk RexiAlo webroot directory IPC$ IPC IPC Service (RexiAlo Samba Server) Domain=[WORKGROUP] OS=[Unix] Server=[Samba 4.1.11] Server Comment --------- ------- Workgroup Master --------- ------- The problem is when I try to map to the smb webroot from Windows 7, it asks for user/pass but just times out and then prompts for credentials. The samba.log file does not show any activity other than the startup of the smbd process. Any help would be appreciated.

  Read the article

• How to remove a directory which looks corrupted

  - by hap497

  Hi, I am using ubuntu 9.10. And I only directory, it shows as '?' for user/ownership. How can I remove it? -rw-r--r-- 1 hap497 hap497 1822 2010-01-28 22:48 IntSizeHash.h d????????? ? ? ? ? ? .libs/ -rw-r--r-- 1 hap497 hap497 194 2010-02-25 12:12 libwebkit_1_0_la-BitmapImage.lo I have tried "$ sudo rm -Rf .libs rm: cannot remove `.libs': Input/output error" Thank you for any pointers.

  Read the article

• How can I get a notification from my server if the mail queue stops

  - by Ash

  I am using QMail with Plesk 10 on an Apache server. Occasionally the mail queue stops processing emails - this most recently happenend when an email account got hacked and started sending hundreds of emails. We did not find out about this until a client of ours contacted to say that their emails were not being recieved, so we checked the mail queue and lo and behold the service had stopped. In future I would like to be notified when the mailqueue stops. How can I set something up so the server will run a command whenever the mailqueue stops?

  Read the article

• Unable to ping between subnets and out to internet

  - by battlemidget

  My setup is Modem - Linksys router - Laptop with 2 devices (wlan0/eth0) - desktop machine Router is 192.168.1.1 gateway to the internet Laptop wlan0 is 192.168.1.4 with a gw of 192.168.1.1 Laptop eth0 is 192.168.2.254 which acts as a second gateway desktop is 192.168.2.100 On laptop i've setup ip_forward to 1, and have inserted 2 iptables rules -A FORWARD -i eth0 -o wlan0 -j ACCEPT -A FORWARD -i wlan0 -o eth0 -j ACCEPT The laptop can ping outside the network (i,e, yahoo.com) it can not ping 192.168.2.100. The desktop can ping 192.168.2.254 but nothing outside the network or 192.168.1.0 subnet. On laptop ip route show lists: 192.168.2.0/24 dev eth0 proto kernel scope link src 192.168.2.254 192.168.1.0/24 dev wlan0 proto kernel scope link src 192.168.1.4 127.0.0.0/8 dev lo scope link default via 192.168.1.1 dev wlan0 What am I missing to make my desktop go through the laptop in order to access the router which provides access to the internet? Thanks

  Read the article

• ssh asks for password despite ssh-copy-id

  - by Aliud Alius

  I've been using public key authentication on a remote server for some time now for remote shell use as well as for sshfs mounts. After forcing a umount of my sshfs directory, I noticed that ssh began to prompt me for a password. I tried purging the remote .ssh/authorized_keys from any mention the local machine, and I cleaned the local machine from references to the remote machine. I then repeated my ssh-copy-id, it prompted me for a password, and returned normally. But lo and behold, when I ssh to the remote server I am still prompted for a password. I'm a little confused as to what the issue could be, any suggestions?

  Read the article

• iptables redirect single website traffic to port 8080

  - by Luke John Southard

  My goal is to be able to make a connection to one, and only one, website through a proxy. Everything else should be dropped. I have been able to do this successfully without a proxy with this code: ./iptables -I INPUT 1 -i lo -j ACCEPT ./iptabels -A OUTPUT -p udp --dport 53 -j ACCEPT ./iptables -A OUTPUT -p tcp -d www.website.com --dport 80 -j ACCEPT ./iptables -A INPUT -m conntrack --cstate ESTABLISHED,RELATED -j ACCEPT ./iptables -P INPUT DROP ./iptables -P OUTPUT DROP How could I do the same thing except redirect the traffic to port 8080 somewhere? I've been trying to redirect in the PREROUTING chain in the nat table. I'm unsure if this is the proper place to do that tho. Thanks for your help!

  Read the article

• How to remove a directory which looks corrupted

  - by hap497

  I am using Ubuntu 9.10. When I examine a directory, it shows as '?' for user/ownership. How can I remove it? -rw-r--r-- 1 hap497 hap497 1822 2010-01-28 22:48 IntSizeHash.h d????????? ? ? ? ? ? .libs/ -rw-r--r-- 1 hap497 hap497 194 2010-02-25 12:12 libwebkit_1_0_la-BitmapImage.lo I have tried rm and sudo rm but get an error: $ sudo rm -Rf .libs rm: cannot remove `.libs': Input/output error Thank you for any pointers.

  Read the article

• Networking issues with WNR3500L

  - by ageis23

  When I try connecting to my wireless network it attempts to connect then gives up. There's something strange going on with the mac's. The eternet switch and all the vlan interfaces have a mac 00:FF:FF:FF:FF:FF. config 'switch' 'eth0' option 'vlan0' '2 3 4 8*' option 'vlan1' '0 8' option 'vlan2' '1 8' config 'interface' 'loopback' option 'ifname' 'lo' option 'proto' 'static' option 'ipaddr' '127.0.0.1' option 'netmask' '255.0.0.0' config 'interface' 'lan' option 'type' 'bridge' option 'ifname' 'eth0.1' option 'proto' 'static' option 'netmask' '255.255.255.0' option 'ipaddr' '192.168.2.1' option 'ip6addr' '' option 'gateway' '192.168.1.253' option 'ip6gw' '' option 'dns' '' config 'interface' 'wan' option 'ifname' 'eth0' option 'proto' 'dhcp' option 'ipaddr' '192.168.1.8' option 'ip6addr' '' option 'netmask' '255.255.255.0' option 'gateway' '192.168.1.253' option 'ip6gw' '' option 'dns' '192.168.1.253' config 'interface' 'dmz' option 'ifname' 'eth0.2' option 'proto' 'static' option 'ipaddr' '192.168.0.1' option 'netmask' '255.255.255.0' Any help on this will be greatly appreciated! When I try setting the mac using macaddr it does nothing. It works perfectly fine when I turn the authentication off.

  Read the article

< Previous Page | 17 18 19 20 21 22 23 24 25 26 27 28  | Next Page >