Search Results

Search found 744 results on 30 pages for 'metric scantlings'.

Page 21/30 | < Previous Page | 17 18 19 20 21 22 23 24 25 26 27 28 | Next Page >

Problems with wired ethernet connection Ubuntu 11.10

- by Andrew Fielden

After some partition shuffling, I've got a problem on my 11.10 system. The wired ethernet interface fails to come up, although the wireless interface is working. I'm using NetworkManager. I thought this may be a problem with NetworkManager, so I checked the config files, which look ok. I then tried re-installing the package, but this didn't resolve the issues. I'm not sure at this point if the problem is due to software configuration, or a hardware problem. I've also tried the cable in other router ports, but same problem. The symptoms are:- System settings - Network reports that the cable is unplugged (it isn't) ifconfig reports the following eth0 Link encap:Ethernet HWaddr f0:4d:a2:a2:a7:fe UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:10 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:792 (792.0 B) TX bytes:0 (0.0 B) Interrupt:46 Base address:0xe000 My /etc/network/interfaces file has the following: auto lo iface lo inet loopback My /etc/resolv.conf file has the following: # Generated by NetworkManager The router's red light is on for this port dmesg reports ADDRCONF(NETDEV_UP): eth0: link is not ready

Read the article
Must developers understand the business domain or should the specification be sufficient?

- by Jerome C.

I work for a company for which the domain is really difficult to understand because it is high technology in electronics, but this is applicable to any software development in a complex domain. The application that I work on displays a lot of information, charts, and metrics which are difficult to understand without experience in the domain. The developer uses a specification to describe what the software must do, such as specifing that a particular chart must display this kind of metrics and this metric is the following arithmetic formula. This way, the developer doesn't really understand the business and what/why he is doing this task. This can be OK if specification is really detailled but when it isn't or when the author has forgotten a use case, this is quite hard for the developer to find a solution. At the other hand, training every developer to all the business aspects can be very long and difficult. Should we give more importance to detailled specification (but as we know, perfect specification does not exist) or should we train all the developers to understand the business domain? EDIT: keep in mind in your answer that the company could used external developpers.

Read the article
Should you put personal beliefs in your program?

- by TheLQ

Recently I've found two examples of programmer's personal beliefs in programs that have removed or crippled useful functionality uTorrent using KB (rarely used) vs Kb (what most ISPs and other programs use as their metric) in their current connection speed. Various attempts by others and me to give options to at least give an option to show in Kb have ended with "ISPs should use KB" Kleopatra (gpg4Win key manager) not having PGP Key Pictures since they "give a false sense of security" and "increase the size of certificates". While the latter is true, the former is debatable. Both of these hurt the program and its usefulness to me. uTorrent's forums used to be filled with people saying they have 10 Mb download pipe but uTorrent only goes up to 2 MB (not knowing that Mb != MB), and with feature requests to show in Mb. Kleopatra has lost usefulness to me since I don't have the functionality to add pictures to PGP keys. These all are political statements; developers attempting to make change in, in their minds important, issues. But should this come at a cost to end user functionality? If a programmer heavily believes X but everyone else believes Y, should the programmer refuse to add support for Y because in their mind X is horrible? In short, should a programmer make political statements in their program?

Read the article
What is the optimum number of admins to server?

- by monocasa

Hello all. I'm starting a business, and I'd like to know what you guys think the optimum number of admins to server ratio is for financial modeling reasons. Or if there's a better metric to use? I come from an embedded programming background so this is an area that I'm pretty squishy on knowledge-wise. : \ Additional Info: There will be a lot of servers. Mainly Linux boxes, with about 10% Windows boxes. Thanks in advance!

Read the article
Dnsmasq offering IP via DHCP, but nobody is accepting

- by Matt

As clients connect the logs light up with DHCPDISCOVER(wlan0) and DHCPOFFER(wlan0) but the IPs being offered are not being accepted. Currently dnsmasq offers IPs on eth1 which works flawlessly. It seems to be just wlan0 that poses this problem for me today. ifconfig of wlan0: wlan0 Link encap:Ethernet HWaddr aa:aa:aa:aa:aa:aa inet addr:10.0.0.2 Bcast:10.255.255.255 Mask:255.0.0.0 inet6 addr: fe80::baa3:86ff:fe70:796a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1609 errors:0 dropped:0 overruns:0 frame:0 TX packets:1268 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:308739 (301.5 KiB) TX bytes:319185 (311.7 KiB)

Read the article
Another good free utility - Campwood Software Source Monitor

- by TATWORTH

The Campwoood Source Monitor at http://www.campwoodsw.com/sourcemonitor.html says in its introduction "The freeware program SourceMonitor lets you see inside your software source code to find out how much code you have and to identify the relative complexity of your modules. For example, you can use SourceMonitor to identify the code that is most likely to contain defects and thus warrants formal review. SourceMonitor, written in C++, runs through your code at high speed, typically at least 10,000 lines of code per second." It is indeed very high-speed and is useful as it: Collects metrics in a fast, single pass through source files. Measures metrics for source code written in C++, C, C#, VB.NET, Java, Delphi, Visual Basic (VB6) or HTML. Includes method and function level metrics for C++, C, C#, VB.NET, Java, and Delphi. Offers Modified Complexity metric option. Saves metrics in checkpoints for comparison during software development projects. Displays and prints metrics in tables and charts, including Kiviat diagrams. Operates within a standard Windows GUI or inside your scripts using XML command files. Exports metrics to XML or CSV (comma-separated-value) files for further processing with other tools.

Read the article
Routing tables don't show ppp0 after 12.04 kernel upgrade to 3.5.0: Haier CE682 modem configuration

- by ubunsteve

I'm trying to get my Haier CE682 EVDO modem, model number 201e:1022 to work in ubuntu 12.04 kernel 3.5.0-030500-generic #201207211835 . I had it working in a previous 12.04 kernel, using compat-wireless and these instructions http://zulkhamsyahmh.blogspot.com/2012/05/install-smartfren-haier-ce682-on-ubuntu.html, and to get it working had to edit the routing tables so that there was a ppp0 showing up, as suggested at http://www.linuxquestions.org/questions/slackware-14/wvdial-is-connecting-but-im-unable-to-do-anything-714861/ Network manager doesn't work with this modem, so I use either wvdial or gpppon to connect to it, both which work (after I run the command sudo modprobe usbserial vendor=0x201e product=0x1022 ) This is the output of when I connect with gpppon to the modem: Using interface ppp0 Connect: ppp0 <-- /dev/ttyUSB0 sent [LCP ConfReq id=0x1 ] rcvd [LCP ConfAck id=0x1 ] rcvd [LCP ConfReq id=0x2 ] sent [LCP ConfAck id=0x2 ] sent [LCP EchoReq id=0x0 magic=0x819c86db] rcvd [CHAP Challenge id=0x1 <1ac8f12799e953967a3cc222c9254690, name = ""] sent [CHAP Response id=0x1 <6f12a903dc40915ca2761c17b87f8fbd, name = "smart"] rcvd [LCP EchoRep id=0x0 magic=0x0] rcvd [CHAP Success id=0x1 ""] CHAP authentication succeeded CHAP authentication succeeded sent [CCP ConfReq id=0x1 ] sent [IPCP ConfReq id=0x1 ] rcvd [IPCP ConfReq id=0x1 ] sent [IPCP ConfAck id=0x1 ] rcvd [CCP ConfReq id=0x1] sent [CCP ConfAck id=0x1] rcvd [CCP ConfRej id=0x1 ] sent [CCP ConfReq id=0x2] rcvd [IPCP ConfRej id=0x1 ] sent [IPCP ConfReq id=0x2 ] rcvd [CCP ConfAck id=0x2] rcvd [IPCP ConfNak id=0x2 ] sent [IPCP ConfReq id=0x3 ] rcvd [IPCP ConfAck id=0x3 ] not replacing existing default route via 192.168.3.1 local IP address 10.191.248.154 remote IP address 10.17.95.25 primary DNS address 10.17.3.244 secondary DNS address 10.17.3.245 as you can see there is a problem with "not replacing existing default route via 192.168.3.1" This it the out put of route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 192.168.3.1 0.0.0.0 UG 0 0 0 wlan0 link-local * 255.255.0.0 U 1000 0 0 wlan0 192.168.3.0 * 255.255.255.0 U 2 0 0 wlan0 I had tried these commands, which had previously worked in the earlier kernel: route del default route add default ppp0 but that broke my wireless internet connection. I then added the default routing as shown above with sudo route add default gw 192.168.3.1 wlan0 So it seems I need to add or change the routing to show a ppp0 connection, but I don't know how to do that.

Read the article
how to change interface ip in ifconfig with /etc/network/interfaces

- by user2478348

Hi everybody when modifiying /etc/network/interfaces, saving it and then executing ifconfig i can't see the modification i made..for example here is part of my /etc/network/interfaces: auto wlan1 iface wlan1 inet static address 192.168.0.60 netmask 255.255.255.0 gateway 192.168.0.61 you can see that the IP address of my wlan1 is 192.168.0.60 but when typing ifconfig i have this: wlan1 Link encap:Ethernet HWaddr 00:19:70:0f:c2:9c inet adr:192.168.0.1 Bcast:192.168.0.255 Masque:255.255.255.0 adr inet6: fe80::219:70ff:fe0f:c29c/64 Scope:Lien UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Packets reçus:758 erreurs:0 :0 overruns:0 frame:0 TX packets:610 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 lg file transmission:1000 Octets reçus:73490 (73.4 KB) Octets transmis:127883 (127.8 KB) (the inet adr:192.168.0.1 and not 198.168.0.60)..if someone can help me I'll be very thankful :)

Read the article
Connected to wireless, but no internet access

- by boogaloo

After installing Ubuntu 12.04 a week ago wireless internet had been working fine. It stopped working yesterday, however, and I'm at a loss for what to do even after scouring replies to similar posted problems. I have tried using Google's public DNS and turning off proxy settings on Firefox. I have used nm-tool and lshw to make sure my wireless device and driver are connected. If anyone can help me resolve this issue I would be extremely grateful! @kregerjd $ ping -c3 www.google.com ping: unknown host www.google.com @Alaa: $ route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 wlan0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 wlan0 192.168.1.0 0.0.0.0 255.255.255.0 U 2 0 0 wlan0 $ ping -c4 192.168.1.1 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data From 192.168.1.104 icmp_seq=1 Destination Host Unavailable From 192.168.1.104 icmp_seq=2 Destination Host Unavailable --- 192.168.1.1 ping statistics --- 4 packets transmitted, 0 received, +2 errors, 100% packet loss, time 2998ms pipe 4

Read the article
Very High Network out in ec2 instance

- by Jatin

I launched an ubuntu-14.04-64bit instance in Amazon EC2 two days back. And I started Tomcat 7.0.54 in that instance and deployed my application war files. It has no other software installed other than tomcat and the default ones. In the past 2 days, its shows 858 GB of Data Transfer(Network Out) from that instance. I have attached a graph of Amazon CloudWatch Metric "Network Out" My application does not do any data download/upload. Its a Java Spring application and the front end is in HTML&Javascript. My application traffic was very low (less than 20 hits) in those 2 days. Is there a way to find out why these data transfers happened and also to find what data has been transferred. If you can see in graph, network out was 20gb per minute. Some more info: Network in was negligible CPU Utilization was very high Everything else was low

Read the article
ip routes to specific interface

- by user65053

I am trying to figure out how to get all traffic to 10.8.78.* to connect using interface ppp0 when available how would I properly handle this (centos) and can I fall back on eth0 when pp0 is not up? /sbin/route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 69.19.219.69 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 10.0.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 0.0.0.0 10.0.1.1 0.0.0.0 UG 0 0 0 eth0

Read the article
Google Analytics: How long does it take users to trigger an event

- by Stephen Ostermiller

I implemented Google Analytics event tracking on my currency conversion website. The typical user flow is: User lands on a page about two currencies. User enters an amount to be converted. The site shows the user the value in the other currency. The JavaScript sends Google Analytics an "converted" event when the currency conversion is done. Because most of the sessions on my site are single page, the event tracking is very important to me to be able to know if users find my page useful. I'm looking for a way to be able to figure out how long it typically takes users to enter a value in the form. I expect that this data would form a bell curve with around a specific amount of time after page load. If I can't get a graph, I could make do with a median value. I would like to be able to use this as a core metric around usability testing. Is there a way to get this information out of Google Analytics?

Read the article
Internet unusably slow with Realtek Semiconductor Co., Ltd. RTL8111/8168B card

- by user42424

So I have recently installed Ubuntu 11.10 for a dual boot with wind 7. After the install I had like 300 updates, so I installed them. At first I could use the internet, although it was extremely slow. However now I cannot, sometimes it will load and others it will simply time out. When I try to download something it will either take forever or will not at all. This is a wired system. On Windows side my speeds are fine. Any help would be greatly appreciated. Also like I said I am new to Linux/Ubuntu so please be nice. One last thing, I also installed 11.10 for same dual boot on my laptop, and wireless speed is the same as on Windows? Only the wired desktop gives me the problem? Hear is some hardware info.. Hope it helps. Mobo: Gigabyte GA=880GMA- AMD / CPU: AMD Phenom (tm) IIx4 965 / 16 GB Ram / Realtek PCIe GBE Family Controller / Cisco Linksys E2000 / Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) / eth0 Link encap:Ethernet HWaddr 50:e5:49:33:64:cf inet addr:192.168.1.118 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::52e5:49ff:fe33:64cf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:76722 errors:0 dropped:76722 overruns:0 frame:76722 TX packets:49692 errors:0 dropped:65 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:107956638 (107.9 MB) TX bytes:4342553 (4.3 MB) Interrupt:44 Base address:0x2000 thanks to roadmr problem solved! I powered down PC, un plugged power from pc end, waited a few (maybe 3)minutes. plugged power back in, pushed and held power button for 30 + seconds. Let go, powered on PC, and my Internet is fine! downloads and web speed blaze, just like on my Win 7 boot, maybe even faster. Problem Solved, Thanks to all!! **

Read the article
How to Configure Different Gateways for Different VLANs

- by Bryan

I have around 10 VLANs, and two different internet gateways. I want traffic on some VLANs to use one gateway, and traffic on other VLANs to use another gateway. (e.g. I wish to route server traffic via one gateway and desktop internet traffic down another). Is it possible to configure different default routes for different VLANs on a Dell 6224 switch? Or is their a better way of doing what I'm trying to achieve? The core switch I am using is a Dell PowerConnect 6224 switch. Currently I'm using: ip route 0.0.0.0 0.0.0.0 10.58.3.16 which creates the default gateway for all VLANs. I did consider adding multiple routes with equal metric, and setting ACLs between the VLANs to deny access to the 'wrong' gateway, but that idea just doesn't feel right to me.

Read the article
monitoring load on AWS EC2

- by hortitude

I'm interesting in monitoring our EC2 instances to ensure we scale up when necessary. Right now we are monitoring idle CPU time as our metric. We aren't measuring disk IO as we are not a very disk intensive application. When running on our own hardware in a datacenter I also usually monitor "load" from the top command. My question is: Does it make sense to monitor "load" on a shared env such as EC2? If so, how do you interpret the results?

Read the article
Is Page-Loading Time Relevant?

- by doug

Take this (ServerFault) page for instance. It has about 20 elements. When the last of these has loaded, the page is deemed "loaded"--but not before. This is certainly the protocol used by our testing service (which is among the small group of well-known vendors that offer that sort of service). Obviously this method is based on a clear, definite endpoint--therefore it's easy to apply w/ concomitant reliability. I think it's also the metric used by the popular Firefox plugin, 'YSlow.' For my employer's website, nearly always the last-to-load items are tracking code, tracking pixels, etc., so from the user's point of view--their perception--the page was "loaded" well before it had actually loaded based on the criterion used by our testing service (15-20% is a rough estimate). I'm sure i'm not the first person to consider this nor the first to wonder if it is causing micro-optimization while ignoring overall system-level, or user-perceived performance. So my question is, are there are other more practical (yet still reasonably precise) measures of page loading time?

Read the article
How do I know if my disks are being hit with too many I/O reads or writes or both?

- by Mark F

I know a bit about disk I/O and bottlenecks relating to this especially when relating to databases. How do I really know what the max I/O numbers will be for my disks? What metric might be available to me for working out roughly (but needs to be a good approximation) of how much capacity (if you will) have I got left available in I/O. I've seen it before where things are bubbling along nicely and then all of a sudden, everything screams to a halt, and it ends up being an I/O bound problem. Is there a better way to predict when I/O is reaching its limits? This article was interesting but not giving the answer I desire. So, is my best bet surrounding just looking at 'CPU I/O WAIT'? There must be a more reactive method than this.

Read the article
How to configure dnsmasq to forward multiple DNS servers?

- by xiaoyi

I'm now using public DNS over VPN to avoid some DNS pollution in China. But this come with a price that I can't take advantage of CDN. Is there a way to configure dnsmasq and let it query both DNS servers, both public one and ISP one, and return the IP with a lower metric? I knew it could be done by using server=/domain/server directive to assign a DNS server for a certain domain, but the problem is there are hundreds of them. So I have to figure out something generic. Thanks in advance.

Read the article
Unable to access internet if wireless enabled

- by balki

The following is my route output. eth0 is my wired network and eth1 is my wireless network. Only wired one has access to internet. If I enable wireless, I am not able to access internet, it tries to access via eth1 and I get 404 page of the wireless router. Why does eth1 have higher preference though default is eth0 (link)? [balakrishnan@mylap ~]$ route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 10.26.0.1 0.0.0.0 UG 0 0 0 eth0 10.26.0.0 * 255.255.192.0 U 1 0 0 eth0 link-local * 255.255.0.0 U 1000 0 0 eth0 192.168.1.0 * 255.255.255.0 U 9 0 0 eth1

Read the article
Ubuntu Server 12.04 as a router. Problem with DNS?? Or Routing table?

- by Lorenzo

I have a virtualbox lab made up of 4 Windows 2008 R2 servers (DC/DNS,SQL,SHAREPOINT, EXCHANGE) that are configured with static ip addresses with NIC's attached to Internal network. Everything works. I had the requirement to execute some tests that also access external services available on the internet. To keep things clean and similar to the production environment I have installed another VM, with Ubuntu Server 12.04 64 bit and configured (I hope) to work as a router like described on this post. This VM has two network interfaces: first is Bridged with the host and is used as a WAN connection and the other one attached in the Internal Network with its own static IP address on the internal network subnet. But actually the Windows servers does not connect to the internet while the unix one connects. I did a route command. this is the result: Kernel IP Routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 10.69.121.1 0.0.0.0 UG 100 0 0 eth0 10.69.121.0 * 255.255.255.0 U 0 0 0 eth0 192.168.83.0 * 255.255.255.0 U 0 0 0 eth1 Can somebody help me with this configuration? :) Thanks! Addendum: I forgot to mention that one of the windows server hosts a DNS service for which I should maybe configure a forwarding server but I do not exactly know which server to forward on... :(

Read the article
When NOT to use a framework

- by Chris

Today, one can find a framework for just about any language, to suit just about any project. Most modern frameworks are fairly robust (generally speaking), with hour upon hour of testing, peer reviewed code, and great extensibility. However, I think there is a downside to ANY framework in that programmers, as a community, may become so reliant upon their chosen frameworks that they no longer understand the underlying workings, or in the case of newer programmers, never learn the underlying workings to begin with. It is easy to become specialized to a degree that you are no longer a 'PHP programmer' (for example), but a "Drupal programmer", to the exclusion of anything else. Who cares, right? We have the framework! We don't need to know how to "do it by hand"! Right? The result of this loss of basic skills (sometimes to the extent that programmers who don't use frameworks are viewed as "outdated") is that it becomes common practice to use a framework where it is not required or appropriate. The features the framework facilitates wind up confused with what the base language is capable of. Developers start using frameworks to accomplish even the most basic of tasks, so that what once was considered a rudimentary process now involves large libraries with their own quirks, bugs, and dependencies. What was once accomplished in 20 lines is now accomplished by including a 20,000 line framework AND writing 20 lines to use the framework. Conversely, one does not want to reinvent the wheel. If I'm writing code to accomplish some basic, common little task, I might feel like I am wasting my time when I know that framework XYZ offers all the features I am after, and a whole lot more. The "whole lot more" part still has me worried, but it doesn't seem that many even consider it anymore. There has to be a good metric to determine when it is appropriate to use a framework. What do you consider the threshold to be, how do you decide when to use a framework, or, when not.

Read the article
Concurrent wireless and wired network

- by Stew Megaw

Hi, I am concerned with maintaining a wireless and wired network connection on my laptop. Basically I can change the metric on each interface so that Windows prefers one connection over the other. I am wondering is following scenario possible.... Some applications uses the wireless while other applications use the wired... I want Internet Explorer (only) to use the wireless connection while Outlook and everything else uses the wired connection. Perhaps adding some lines to the routing table might work? - Adding the ip addresses of websites I want to view via the wireless connection? Many Thanks in advance for any replies!

Read the article
Unable to change IP address for eth0 without restart in Ubuntu

- by Rodnower

I have Ubuntu 12.04.1 installed. I tried to change the IP address of the interface eth0 in /etc/network/interfaces from 192.168.1.3 to 192.168.1.4 auto lo iface lo inet loopback pre-up iptables-restore < /etc/iptables.up.rules auto eth0 iface eth0 inet static address 192.168.1.4 gateway 192.168.1.1 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 sudo service networking status When I issue: sudo service networking restart I get this response: stop: Unknown instance: networking stop/waiting And IP remains 192.168.1.3: eth0 Link encap:Ethernet HWaddr 00:1e:33:71:cd:a4 inet addr:192.168.1.3 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21e:33ff:fe71:cda4/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3861 errors:0 dropped:0 overruns:0 frame:0 TX packets:3291 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3423285 (3.4 MB) TX bytes:521854 (521.8 KB) Interrupt:45 Base address:0x4000 Only after restart does the IP change. Any ideas?

Read the article
How to map a VPN (tun0) network adapter on host Ubuntu to a VirtualBox guest Windows?

- by Mashimom

I have a Ubuntu 10.04 running Oracle VirtualBox 3.2.6 with a Windows XP guest. I use a VPN that I would like to be accessed by the guest VM, on a ifconfig it shows as: tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:5.192.10.99 P-t-P:5.192.10.99 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1362 Metric:1 RX packets:14151 errors:0 dropped:0 overruns:0 frame:0 TX packets:19860 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:4415271 (4.4 MB) TX bytes:17949982 (17.9 MB) Using NAT or Bridge adapters on the VM only gives me the non-vpn adapter. How can I map the tun0 adapter to VirtualBox?

Read the article
Configuring memcached for a particular scenario

- by pradeepchhetri

I have a web application which queries opentsdb server(which in backend using Hbase cluster) for the datapoints of different metrics and using dygraph javascript graphing library, I am plotting those metrics. Since getting all the datapoints of past one day from opentsdb for a particular metric is itself taking nearly 2 seconds, my application which is plotting nearly 25 metrics is becoming very slow. In order to reduce this latency, I am thinking of using memcached module of php5 for caching all the queries. But I have few questions regarding memcached. Is there any way I can configure memcache to keep on updating its cache in the background by running some command line queries after particular interval of time. Is there any way I can configure memcache to always reply for a query using cache instead of first updating its cache because my application just plots datapoints for past one day. Missing out some datapoints is not that critical.

Read the article

< Previous Page | 17 18 19 20 21 22 23 24 25 26 27 28 | Next Page >