Search Results

Search found 3956 results on 159 pages for 'scripting bridge'.

Page 21/159 | < Previous Page | 17 18 19 20 21 22 23 24 25 26 27 28  | Next Page >

• Wrapping a point-to-point link

  - by user3712955

  I'm using a pair of IP radios (non-WiFi) to bridge my office engineering LAN (172.0.0.0/8) to a lab in another building. The radios work fine, but they expose a web management interface I'd like to hide, and they also generate traffic (ARP, STP, and more) that I need to keep off my (very, very clean) LAN segments. I have some ARM-Linux boards (similar to Beagle/Panda/RasPi) running Ubuntu, and I've put one at each end of the link, between the radio and the LAN. Each of the boards has 2 wired Ethernet interfaces, eth0 and eth1. The LAN segments are connected to eth0, and the radios are connected to eth1. I'd like to accomplish the following: Keep radio-originated traffic off my LAN segments! Hide all services provided by the radio (web, ssh, etc.) Transparently pass all traffic between the LAN segments (including things like ARP). The above also applies to the ARM-Linux boards: No stray traffic my LAN from them either! I'd like the system to look like a switch: LAN packets arriving at one eth0 appear at the other. And neither eth0 should have an IP address: The working system should behave like a CAT6 cable with some latency (instead of ARM boards and radios). Unfortunately, I'm confused about how to properly configure the ARM Ubuntu systems. What I'm guessing I need is a bridge on each board (br0?) and a VLAN (vlan0 or eth0.0?) to isolate the LAN traffic from everything else as it passes through the ARM boards and the radios. Then I need some kind of a firewall to block sending anything out eth0 that isn't from the other eth0 (via the VLAN). I've looked at the ip and ebtables commands (especially -t broute). While the concepts sorta-kinda make sense, I'm completely lost in the details. Edit: In the perverse case that a system on one of my LAN segments has the same IP address as one of the radios, or as eth1 on the ARM-Ubuntu boards, a VLAN won't work. Which I believe means I need to tunnel all traffic between the two eth0 interfaces to get that "like a wire" behavior. Help? Finally, I'd like to have a way to temporarily expose services on the ARM boards (ssh) and the radios (web) for maintenance purposes. Ideally, it would expose an IP address with ssh available on port 22. Once connected, I figure I'd start an X11 session and run a browser on the ARM board to access the radios. Or something. I could login via the console to enable/disable this, or perhaps could use a GPIO to trigger a script. I feel I've identified most of the pieces needed to make all this happen, but I have no idea how to combine them to make a working system. Thanks!

  Read the article

• What objects would get defined in a Bridge scoring app (Javascript)

  - by Alex Mcp

  I'm writing a Bridge (card game) scoring application as practice in javascript, and am looking for suggestions on how to set up my objects. I'm pretty new to OO in general, and would love a survey of how and why people would structure a program to do this (the "survey" begets the CW mark. Additionally, I'll happily close this if it's out of range of typical SO discussion). The platform is going to be a web-app for webkit on the iPhone, so local storage is an option. My basic structure is like this: var Team = { player1: , player2: , vulnerable: , //this is a flag for whether or //not you've lost a game yet, affects scoring scoreAboveLine: , scoreBelowLine: gamesWon: }; var Game = { init: ,//function to get old scores and teams from DB currentBid: , score: , //function to accept whether bid was made and apply to Teams{} save: //auto-run that is called after each game to commit to DB }; So basically I'll instantiate two teams, and then run loops of game.currentBid() and game.score. Functionally the scoring is working fine, but I'm wondering if this is how someone else would choose to break down the scoring of Bridge, and if there are any oversights I've made with regards to OO-ness and how I've abstracted the game. Thanks!

  Read the article

• Calling ASP.NET Web API using JQuery ajax - cross site scripting issue

  - by SimonF

  I have a Web API which I am calling using the JQuery ajax function. When I test the service directly (using the Chrome RESTEasy extension) it works fine, however when I call it using the JQuery ajax function I get an error. I'm calling it on port 81: $.ajax({ url: "http://127.0.0.1:81/api/people", data: JSON.stringify(personToCreate), type: "POST", contentType: "application/json;charset=utf-8", statusCode: { 201: function (newPerson) { callback(newPerson); } }, success: function (newPerson) { alert("New person created with an Id of " + newPerson.Id); }, error: function (jqXHR, textStatus, errorThrown) { alert('Error. '+textStatus+'. '+errorThrown); } }); ...but when I trace it using FireBug Lite the response comes from port 82: {"Message":"No HTTP resource was found that matches the request URI 'http://127.0.0.1:82/api/people'.","MessageDetail":"No action was found on the controller 'People' that matches the request."} I think the error is, effectively, due to cross-site scripting being blocked, but I'm not actually cross-site scripting, if you see what I mean. Has anyone else come across this and been able to fix it? Edit: Routing config (global.asax.vb) is: RouteTable.Routes.MapHttpRoute(name:="DefaultApi", routeTemplate:="api/{controller}/{id}", defaults:=New With {Key .id = System.Web.Http.RouteParameter.Optional}) Controller: Public Function PostValue(ByVal departmentid As Integer, ByVal emailaddress As String, ByVal firstname As String, ByVal lastname As String) As Guid Dim context As New WSMModelDataContext Dim bllPeople As New PeopleBLL(context) Return bllPeople.Create(firstname, lastname, emailaddress, departmentid) End Function When I debug it, it doesn't get as far as running the controller, although when calling it through RESTEasy it routes correctly and the controller executes successfully. The only difference seemes to be that wen called through RESTEasy it is (correctly) using http://127.0.0.1:81 but for some reason when called via JQuery/ajax it seems to be using http://127.0.0.1:82.

  Read the article

• How to justify using a scripting language as part of a project

  - by sylvanaar

  I have a specific project in which I want to use either a scripting language + C, or as an alternative a 100% Java solution. The program adapts a legacy system for use with other moderns systems. Basically, I have few choices as to what language I can use. I have C/C++, Java 1.4, and I have also compiled the Lua for this environment. The program does 'screen scraping' and has to deal with alot of strings. That part of the code is highly variable. Most of the developers at my company use C, so - my original design was to write some portions in C, and use Lua for the part that dealt with strings and changed freqently. I was told 'You have to justify your use of the scripting language.' So i reworked my design using 100% Java, and was told - Java wont have enough performance. You should do the whole thing in C. I'm not controlling lasers or doing image processing - just some screen scraping. I still have to provide justification for using anything but C - so what justification can I provide?

  Read the article

• Intel présente ses puces Sandy Bridge, axées sur l'overclocking, la protection de contenus et le contrôle graphique

  Intel présente ses puces Sandy Bridge, axées sur l'overclocking, la protection de contenus et le contrôle graphique Mise à jour du 04.01.2011 par Katleen C'est officiel, Intel va enfin dévoiler ses puces Sandy Bridge tant attendues, et dans les temps annoncés qui plus est. Les produits, qui viennent d'être lancés, seront présentés cette semaine lors du CES de Las Vegas. La gamme Sandy Bridge se compose de 4 Core i3, 12 Core i5 et 13 Core i7 dont 1 qualifié d'Extreme. Comme nous vous l'annoncions en septembre, ces processeurs seront gravés en 32nm et seront optimisés pour un usage dans les ordinateurs portables (laptops, netbooks, etc.), pour des fréquences de 2,2 GHz (po...

  Read the article

• Can't get network bridging to work

  - by Antonis Christofides

  I'm trying to make network bridging to work on a Debian squeeze (I'm experimenting in order to make a QEMU/KVM virtual machine that will be visible to the outside network as if it were a distinct machine). The problem is that when I type brctl addif br0 eth0 then I lose connectivity to the network until I type brctl delif br0 eth0. More specifically, here's how my machine looks like before I do anything (essentially eth0 is listening on 147.102.160.153): root@laura:/home/anthony# ip addr show 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 8c:73:6e:db:1c:1b brd ff:ff:ff:ff:ff:ff inet 147.102.160.153/24 brd 147.102.160.255 scope global eth0 inet6 2001:648:2000:a0:8e73:6eff:fedb:1c1b/64 scope global dynamic valid_lft 2591848sec preferred_lft 604648sec inet6 fe80::8e73:6eff:fedb:1c1b/64 scope link valid_lft forever preferred_lft forever 3: wlan0: <BROADCAST,MULTICAST> mtu 1500 qdisc mq state DOWN qlen 1000 link/ether 4c:ed:de:8e:44:d7 brd ff:ff:ff:ff:ff:ff 4: vboxnet0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000 link/ether 0a:00:27:00:00:00 brd ff:ff:ff:ff:ff:ff 5: pan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN link/ether ee:7c:88:59:d0:e8 brd ff:ff:ff:ff:ff:ff Now let me add the bridge: root@laura:/home/anthony# brctl addbr br0 root@laura:/home/anthony# ip tuntap add dev tap0 mode tap root@laura:/home/anthony# ip link set tap0 up root@laura:/home/anthony# brctl addif br0 tap0 Until here everything continues to work normally. Finally, I try to add eth0 to the bridge: root@laura:/home/anthony# brctl addif br0 eth0 At this point, I no longer have a network connection. If I try to ping something, it tells "Destination Host Unreachable". The output of ip addr show seems normal: root@laura:/home/anthony# ip addr show 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 8c:73:6e:db:1c:1b brd ff:ff:ff:ff:ff:ff inet 147.102.160.153/24 brd 147.102.160.255 scope global eth0 inet6 2001:648:2000:a0:8e73:6eff:fedb:1c1b/64 scope global dynamic valid_lft 2591908sec preferred_lft 604708sec inet6 fe80::8e73:6eff:fedb:1c1b/64 scope link valid_lft forever preferred_lft forever [snip wlan0, vboxnet0 and pan0, which are down and irrelevant] 8: br0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN link/ether 16:30:f2:67:ab:75 brd ff:ff:ff:ff:ff:ff 9: tap0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 500 link/ether 16:30:f2:67:ab:75 brd ff:ff:ff:ff:ff:ff inet6 fe80::1430:f2ff:fe67:ab75/64 scope link valid_lft forever preferred_lft forever Also: root@laura:/home/anthony# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 147.102.160.0 0.0.0.0 255.255.255.0 U 1 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 eth0 0.0.0.0 147.102.160.200 0.0.0.0 UG 0 0 0 eth0 I can't understand what I'm doing wrong. I want the machine to continue to listen on 147.102.160.153 on eth0, and in addition to that I want to have a tap0 interface, bridged to eth0, that will be available to the guest machine so that the latter listens on another ip address (say 147.102.160.205). (If there's another way to achieve what I want, I'm also interested.)

  Read the article

• ubuntu 10.04; kvm bridged networking not working with public ip addresses

  - by senorsmile

  I have a dedicated hosted server box with ubuntu 10.04 64 bit installed. I would like to run kvm with ubuntu 8.04 installed for some php 5.2 compatible apps(they don't work right with php 5.3, the default in ubuntu 10.04). I installed KVM as instructed at https://help.ubuntu.com/community/KVM/Installation . I installed the vm using virt-manager. I never could figure out how use virt-install or any of those automated installers. I just installed it using the disc. I set up bridged networking as per https://help.ubuntu.com/community/KVM/Networking . However, the bridged connection doesn't work. Here's my /etc/network/interfaces on the host, running ubuntu 10.04. (with specific public ip blanked) auto lo iface lo inet loopback auto eth0 iface eth0 inet manual auto br0 iface br0 inet static address xx.xx.xx.xx netmask 255.255.255.248 gateway xx.xx.xx.xa bridge_ports eth0 bridge_stp on bridge_fd 0 bridge_maxwait 10 ` Here's my /etc/network/interfaces on the guest, running ubuntu 8.04. auto lo iface lo inet loopback auto eth0 iface eth0 inet static address xx.xx.xx.xy netmask 255.255.255.248 gateway xx.xx.xx.xa The two vm's can communicate to each other. But, the guest vm can't access anyone in the real world. Here's my /etc/libvirt/qemu/store_804.xml <domain type='kvm'> <name>store_804</name> <uuid>27acfb75-4f90-a34c-9a0b-70a6927ae84c</uuid> <memory>2097152</memory> <currentMemory>2097152</currentMemory> <vcpu>2</vcpu> <os> <type arch='x86_64' machine='pc-0.12'>hvm</type> <boot dev='hd'/> </os> <features> <acpi/> <apic/> <pae/> </features> <clock offset='utc'/> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>restart</on_crash> <devices> <emulator>/usr/bin/kvm</emulator> <disk type='file' device='disk'> <driver name='qemu' type='raw'/> <source file='/var/lib/libvirt/images/store_804.img'/> <target dev='hda' bus='ide'/> </disk> <disk type='block' device='cdrom'> <driver name='qemu' type='raw'/> <target dev='hdc' bus='ide'/> <readonly/> </disk> <interface type='bridge'> <mac address='52:54:00:26:0b:c6'/> <source bridge='br0'/> <model type='virtio'/> </interface> <console type='pty'> <target port='0'/> </console> <console type='pty'> <target port='0'/> </console> <input type='mouse' bus='ps2'/> <graphics type='vnc' port='-1' autoport='yes'/> <sound model='es1370'/> <video> <model type='cirrus' vram='9216' heads='1'/> </video> </devices> </domain> Any idea where I've gone wrong?

  Read the article

• Shell scripting: Way to parse parameters from command line

  - by bguiz

  myscript [-a a-arg] [-c c-arg] [-b] [-e] somedirectory Given that I want my shell script be invoked at the command line using the above parameters - where [these brackets] denote that they are optional - what is the best method to parse them?

  Read the article

• Scripting an automated SQLServer 2008 DR move

  - by ItsAMystery

  Hi All We use the built in logshipping in SQLServer to logship to our DR site but once in a month do a DR test which requires us to move back and forth between our Live and BAckup servers. We run multiple (30) databases on the system so manually backing up the final logs and disabling the jobs is too much work and takes too long. I though no problem, I will script it but have run into trouble with it always complaninig that the final logship is too early to apply even though I dont export the final log until putting the database into norecovery mode. Firstly, does any one no a simple and reliable way of doing this? I have lokoed at some 3rd party software (redgate sqlbackup I think it was) but that didnt make it easy in this situation either. What I want to be able to do is basically run a script (a series of stored procedures) to get me to DR and run another to get me back with no dataloss. My scripts are very simplistic at the moment but here they are: 2 servers Primary Paris Secondary ParisT The StartAgentJobAndWait is a script written by someone else (ta) and just checks the jobs have finished or quits it if it never ends. At the moment I am just using a test database called BOB2 but if I can get it working will pass in the database and job names. from PARIS: /* Disable backup job */ exec msdb..sp_update_job @job_name = 'LSBackup_BOB2', @enabled = 0 exec PARIST.msdb..sp_update_job @job_name = 'LSCopy_PARIS_BOB2', @enabled = 0 exec PARIST.msdb..sp_update_job @job_name = 'LSRestore_PARIS_BOB2', @enabled = 0 exec PARIST.master.dbo.DRStage2 ParisT DRStage2 DECLARE @RetValue varchar (10) EXEC @RetValue = StartAgentJobAndWait LSCopy_PARIS_BOB2 , 2 SELECT ReturnValue=@RetValue if @RetValue = 1 begin print 'The Copy Task completed Succesffuly' END ELSE print 'The Copy task failed, This may or may not be a problem, check restore state of database' SELECT @RetValue = 0 EXEC @RetValue = StartAgentJobAndWait LSRestore_PARIS_BOB2 , 2 SELECT ReturnValue=@RetValue if @RetValue = 1 begin print 'The Restore Task completed Succesffuly' END ELSE print 'The Copy task failed, This may or may not be a problem, check restore state of database' exec PARIS.master.dbo.DRStage3 /* Do the last logship and move it to Trumpington */ BACKUP log "BOB2" to disk='c:\drlogshipping\BOB2.bak' with compression, norecovery EXEC xp_cmdshell 'copy c:\drlogshipping \\192.168.7.11\drlogshipping' EXEC PARIST.master.dbo.DRTransferFinish AS BEGIN restore database "BOB2" from disk='c:\drlogshipping\bob2.bak' with recovery

  Read the article

• Windows or Linux for VPN-VPN Bridge

  - by James

  I have the following network layout: Network1 ----VPN1-----Network2----VPN2----Network3 I can administer everything in Network1 only and my goal is to get to a box on Network3. I've been told by the admins of Network2 that it's not possible for them to route traffic from Network1 to Network3. I've finally been authorised to host a box in Network2 and I'm hoping with this I can set something up to resolve the issue. My question is should I set this up as a Windows or a Linux box. My initial thought was to use iptables to reroute requests but with my lack of experience with Windows Server (used for something or other in Network2) I'm not sure if this will work. My head's full of questions like: - can I get an ip without logging in to a windows domain? - if I do get an ip, do Windows Servers manage routing through the VPN? - can I make a linux box authenticate with Windows Server to log on to the domain? - would it just be easier to set up a windows box? - is it possible to configure a windows box to do routing from Network1 to Network3? Has anyone done anything like this before? Had experience managing Windows Server? Authenticated (or not as the case may be) to a Windows domain? I'd really appreciate your advice. It might be worth mentioning that the overall objective is to establish a telnet connection from a box on Network1 to a box on Network3.

  Read the article

• Web Server Scripting Hack to Maintain State and Keep a Domain Cookieless

  - by jasonspalace

  Hello, I am looking for a solution on a LAMP server to keep a site cookieless such as "example.com", where static content is served from "static.example.com", and with rules in place to rewrite requests for "www.example.com" to "example.com". I am really hoping to avoid setting up a cookieless domain for the static content due to an unanswered SEO concern with regards to CNAMEing to a CDN. Is there a way, (or safe hack), that can be implemented where a second domain such as "www.example2.com" is CNAMEd, aliased, or otherwise used with "example.com" to somehow trick a php application into maintaining state with a cookie dropped on "www.example2.com" therefore keeping all of "example.com" cookieless? If such a solution is feasible, what implications would exists with regards to SSL and cross-browser compatibility other than requiring users to accept cookies from 3rd party domains and possibly needing an additional SSL to keep the cookie secure? Thanks in advance to all.

  Read the article

• Scripting a Windows 2008 Cluster from Windows 2003

  - by glancep

  Our current environment is all Windows 2003. When we migrate a new version of our service to the cluster, we first stop the service with a command like: cluster.exe <clusterName> resource "<serviceName>" /offline We do similarly after the migrate to bring the service back online. Now, we are upgrading our environment to new Windows 2008 servers. However, our build/migrate machine will remain Windows 2003. When issuing the same command from Windwos 2003 to Windows 2008, we get: System error 1722 has occurred (0x000006ba). The RPC server is unavailable. We need to be able to remotely administer a Windows 2008 cluster from a Windows 2003 server in an automated fashion (such as the command-line cluster.exe utility). Is this possible? Thanks, Gideon

  Read the article

• Batch Scripting - Listing files with a specific amount of characters in file name

  - by Jane

  I'm creating a batch script for a class and I've hit a roadblock I have to list all text files whose names are up to seven characters long on the whole c: drive - make the listing output in a wide formant - then append to Batch script file output.txt So far I have -- dir c:*txt/w/o/s/p c:/"My Batch Script File Assigment"/"Output"/"Batch Script File Output Data".txt The above does everything except limit the search to files with only 1-7 characters in their name. If anyone could point me in the right direction I would really appreciate it!

  Read the article

• ash scripting: space-containing variable refuses to be grepped

  - by Luci Sandor

  I am trying to run the script listed at http://talk.maemo.org/showthread.php?t=70866&page=2 on its intended hardware, a Nokia Linux phone running BusyBox ash. The script receives the name of WiFi network as a parameter, and tries to connect the phone to it. I suspect the script works, but my SSID, BU (802.1x), has space and parentheses in it. So when I type at the command prompt autoconnect.sh BU\ \(802.1x\) I get various errors. First, LIST=`iwconfig wlan0 | awk -F":" '/ESSID/{print $2}'` if [ $LIST = "\"$1\"" ]; then ...fails, even I am connected to the network. The error is not avoided by using single or double quotes instead of escaping characters at the command prompt. Second, if [ -z `iwlist wlan0 scan | grep -m 1 -o \"$1\"` ]; then echo SSID \"$1\" not found; shows that grep does not find the string, although the same grep, typed directly into the command prompt, does find 'BU (802.1x)'. How do I quote $1 in the two circumstances above so that it will work with my network SSID, containing spaces and parentheses? Thank you.

  Read the article

• Scripting Dell DRAC 6 to set boot device

  - by derfred

  I have a couple of servers with DRAC 6 cards for which I want to set the boot device to PXE via a script. The Web GUI has the option under the "Setup" tab and "First Boot Device". How can I set (and unset) this option in a script?

  Read the article

• How do I bridge connections in windows 7?

  - by Wolfgang Haak

  At work, our ISP has gone down, 3 days running. A company next door has kindly provided us with access to their wireless network, and I'd like to get our internal mail server (win 7) to become online via that wireless connection, while being accessible from within the LAN, but I'm struggling with the windows configuration. Our company's LAN subnet (wired interface) sits on 192.168.0. Neighbour's wireless subnet 192.168.1. I've tried bridging the connections but that disconnects the mail server from the Internet connection and the LAN. what do I have to do achieve this networking configuration? Kind regards, Wolfgang

  Read the article

• How do I choose which Ethernet Adapter to bridge in VMPlayer

  - by Catherine MacInnes

  I am running vmplayer 3.1.0 on Ubuntu. The host machine has four ethernet adapters that are configured to run on four different subnets. I need to run four VMs each with a single ethernet adapter bridged onto a specific one of the physical ethernet adapters. Does anyone know how to do this? Am I simply exceeding the capabilities of vmplayer and have to go to one of the other vmware products, if so, which one. Note that I have no need to create additional VMs, these are VMs that are being given to me by companies that want us to develop software for their products.

  Read the article

• WPA Enterprise Wireless Bridge

  - by prestomation

  I live in college housing at a university with wifi available. unfortunately, my bedroom(where I'd like to place my PC) gets little to no reception. I'd like to place a router in the strongest spot and rebroadcast. I understand this can be done with DD-WRT/etc, but this particular network is WPA Enterprise with my own personal username/password. I can't find any concrete evidence that I can get my router to act as a repeater for this encryption. I don't currently have a router to test it on, otherwise this would be easy, I just don't want to buy a router if it will be worthless to me. Thanks for your help

  Read the article

• Bridge 2 routers

  - by Nathan Adams

  I have 2 Linksys WRT54GL routers flashed with DD-WRT. On each I have a different ISP, and thus a different private network. I would like to be able to talk to either network regardless of what network I am on. Example: ISP1 - Router1 - Client ISP2 - Router2 - Client What I would like to do is something like: ISP1 - Router1 - Client              ^              |              v ISP2 - Router2 - Client This would be ideally because then I don't need to introduce another device in the mix, unless I have to. But I guess the first question is - is this even possible?

  Read the article

• A PCI-to-PCI bridge cannot start

  - by midtiby

  Hi I'm trying to use a DeLock PCMCIA adapter, CardBus to 2 x FireWire to get firewire connectivity on my laptop. It worked a few weeks ago, but now I get the message. "This device cannot start (Code 10)" when I look it up in Device manager. Any ideas of how to get it up and running? I am running Windows XP SP3

  Read the article

• Batch scripting: iterate over drive letters?

  - by kdt

  In windows batch scripts, how can I iterate over all drive letters which correspond to physical volumes or mapped shares?

  Read the article

• Scripting a permanent CTRL / CAPS swap in Gnome?

  - by Duncan Bayne

  I have a bash script that I use to configure a vanilla Ubuntu (10.10 Maverick Meerkat) installation to be exactly the way I want it. I make extensive use of gconftool-2 to configure the desktop, set up shortcut keys, etc. Now, I'm trying to swap the CTRL and CAPS keys. I have found two ways of doing this: In Gnome, go to System - Preferences - Keyboard - Layout - Options and make the change in there. This works well, but I don't know how to script this; the setting doesn't seem to be stored in the usual place as I can't find it with gconf-editor. Add the line setxkbmap -option "ctrl:swapcaps" to my .bashrc file. That works too, until I suspend the machine & then resume it. At that point the CTRL and CAPS behaviour return to normal, until I cause .bashrc to be run again by opening a new shell. This behaviour has been reported as a bug in RedHat. Could someone please suggest a way of switching those keys that is both permanent, and can be scripted? I'm sure I must be missing something obvious here ...

  Read the article

• Cisco NAT vs Bridge vs BVI

  - by cjavapro

  The only devices on this particular LAN will all have public IP addresses. Also the public IP address will be configured directly on the machine,,, so we will not translate private/public IP addresses. If we use NAT,, we would have to translate the public IP on the WAN to the public IP on the LAN. The only security feature I expect on the gateway is an access list. I don't really know much about networking, so I am sorry if this question is generic.

  Read the article

• OpenVPN bridge network from routed clients

  - by gphilip

  I have the following setup: subnet 1 - 10.0.1.0/24 with a machine used as NAT and also running an OpenVPN client subnet 2 - 192.168.1/24 with an OpenVPN server (the server in subnet 1 connect here) subnet 3 - 10.0.2.0/24 that uses the NAT machine (subnet 1) to access the internet, so all non-local traffic is routed there to the eth0 interface The OpenVPN client creates the tun0 interface and appropriate routing so that I can access machines from 192.168.1/24 [root@ip-10-0-1-208 ~]# telnet 192.168.1.186 8081 Trying 192.168.1.186... Connected to 192.168.1.186. Escape character is '^]'. [root@ip-10-0-1-208 ~]# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 10.0.1.1 0.0.0.0 UG 0 0 0 eth0 10.0.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.8.0.1 10.8.0.5 255.255.255.255 UGH 0 0 0 tun0 10.8.0.5 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 169.254.169.254 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 192.168.0.0 10.8.0.5 255.255.0.0 UG 0 0 0 tun0 However, when I try the same from subnet 3, it can't reach that machine. [root@ip-10-0-2-61 ~]# telnet 192.168.1.186 8081 Trying 192.168.1.186... I suspect that it's because subnet 3 is routed to eth0 on the NAT machine in subnet 1 and it cannot jump to tun0. What's the easiest way to resolve it? I don't want to use iptables. I can't change the routing from machines in subnet 1 because it's done in AWS and so it works only with specific interfaces. Also, the NAT machine gets its IP with DHCP and so bridging is a bit complicated. IP forwarding is set on the NAT machine [root@ip-10-0-1-208 ~]# cat /proc/sys/net/ipv4/ip_forward 1 Thank you!

  Read the article

• Mongo Scripting the shell

  - by cKendrick

  On my production stack, I have a front-end server and a Mongo server. I would like to be able to set a cron job on the front-end server to create some logs daily. I wrote a script that does this: ./mongo server:27017/dbname --quiet my_commands.js If I run it from the Mongo server as above, it works fine. However, I would like to be able to run it from the front-end server. When I try to do that, I get: -bash: mongo: command not found Since mongo is not installed on the front end server, it gives me that error. Is it possible to somehow bind mongo to my mongo on the Mongo server?

  Read the article

< Previous Page | 17 18 19 20 21 22 23 24 25 26 27 28  | Next Page >