Search Results

Search found 10280 results on 412 pages for 'remote shutdown'.

Page 210/412 | < Previous Page | 206 207 208 209 210 211 212 213 214 215 216 217  | Next Page >

• Cisco: unable to negotiate IP using IPCP with Windows server

  - by lnk

  I am connecting to Windows server using PPP (for vpn), I establish connection but server does not respond me for my address requests: *Mar 23 00:40:06.055: Vi1 MS-CHAP-V2: I CHALLENGE id 0 len 25 from "MSDC" *Mar 23 00:40:06.063: Vi1 MS CHAP V2: Using hostname from interface CHAP *Mar 23 00:40:06.063: Vi1 MS CHAP V2: Using password from interface CHAP *Mar 23 00:40:06.067: Vi1 MS-CHAP-V2: O RESPONSE id 0 len 69 from "XXX" *Mar 23 00:40:06.087: Vi1 PPP: I pkt type 0xC223, datagramsize 50 link[ppp] *Mar 23 00:40:06.087: Vi1 MS-CHAP-V2: I SUCCESS id 0 len 46 msg is "S=XXX" *Mar 23 00:40:06.087: Vi1 MS CHAP V2 No Password found for : XXX *Mar 23 00:40:06.091: Vi1 MS CHAP V2 Check AuthenticatorResponse Success for : XXX *Mar 23 00:40:06.091: Vi1 IPCP: O CONFREQ [Closed] id 1 len 20 *Mar 23 00:40:06.091: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:06.091: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:07.091: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1, changed state to up *Mar 23 00:40:07.091: Vi1 LCP: O ECHOREQ [Open] id 1 len 12 magic 0x194CAFCF *Mar 23 00:40:07.103: Vi1 LCP-FS: I ECHOREP [Open] id 1 len 12 magic 0x361B62E5 *Mar 23 00:40:07.103: Vi1 LCP-FS: Received id 1, sent id 1, line up *Mar 23 00:40:08.083: Vi1 IPCP: TIMEout: State REQsent *Mar 23 00:40:08.083: Vi1 IPCP: O CONFREQ [REQsent] id 2 len 20 *Mar 23 00:40:08.083: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:08.083: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:10.099: Vi1 IPCP: TIMEout: State REQsent *Mar 23 00:40:10.099: Vi1 IPCP: O CONFREQ [REQsent] id 3 len 20 *Mar 23 00:40:10.099: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:10.099: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:12.115: Vi1 IPCP: TIMEout: State REQsent *Mar 23 00:40:12.115: Vi1 IPCP: O CONFREQ [REQsent] id 4 len 20 *Mar 23 00:40:12.115: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:12.115: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:12.211: Vi1 LCP: O ECHOREQ [Open] id 2 len 12 magic 0x194CAFCF *Mar 23 00:40:12.219: Vi1 LCP-FS: I ECHOREP [Open] id 2 len 12 magic 0x361B62E5 *Mar 23 00:40:12.219: Vi1 LCP-FS: Received id 2, sent id 2, line up *Mar 23 00:40:14.131: Vi1 IPCP: TIMEout: State REQsent *Mar 23 00:40:14.131: Vi1 IPCP: O CONFREQ [REQsent] id 5 len 20 *Mar 23 00:40:14.131: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:14.131: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:16.147: Vi1 IPCP: TIMEout: State REQsent *Mar 23 00:40:16.147: Vi1 IPCP: O CONFREQ [REQsent] id 6 len 20 *Mar 23 00:40:16.147: Vi1 IPCP: VSO OUI 0x00000C kind 1 (0x000A00000C0100000000) *Mar 23 00:40:16.147: Vi1 IPCP: Address 0.0.0.0 (0x030600000000) *Mar 23 00:40:17.331: Vi1 LCP: O ECHOREQ [Open] id 3 len 12 magic 0x194CAFCF *Mar 23 00:40:17.343: Vi1 LCP-FS: I ECHOREP [Open] id 3 len 12 magic 0x361B62E5 *Mar 23 00:40:17.343: Vi1 LCP-FS: Received id 3, sent id 3, line up You see: My router asks for address, but only keepalives are on line. But the same server works with windows client!! ! version 12.4 no service pad service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption service internal ! hostname Router ! boot-start-marker boot-end-marker ! ! no aaa new-model ! resource policy ! ip subnet-zero ! ! ip cef vpdn enable ! vpdn-group pptp request-dialin protocol pptp pool-member 1 initiate-to ip XXXX ! ! ! ! ! ! ! bridge irb ! ! interface ATM0 no ip address shutdown no atm ilmi-keepalive dsl operating-mode auto ! interface FastEthernet0 ! interface FastEthernet1 ! interface FastEthernet2 ! interface FastEthernet3 ! interface Dot11Radio0 no ip address shutdown speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0 station-role root ! interface Vlan1 no ip address bridge-group 1 ! interface Dialer0 ip address negotiated encapsulation ppp dialer pool 1 dialer idle-timeout 0 dialer string XXX dialer persistent dialer vpdn dialer-group 1 keepalive 5 3 no cdp enable ppp authentication ms-chap-v2 optional ppp eap refuse ppp chap hostname XXX ppp chap password 0 XXX ppp ipcp mask request ppp ipcp ignore-map ppp ipcp address accept ! interface BVI1 mac-address XXX.XXX.XXX ip address dhcp ! ip classless ip route 172.0.0.0 255.0.0.0 Dialer0 ! no ip http server no ip http secure-server ! dialer-list 1 protocol ip permit ! control-plane ! bridge 1 protocol vlan-bridge bridge 1 route ip ! line con 0 no modem enable line aux 0 line vty 0 4 login ! scheduler max-task-time 5000 end

  Read the article

• Windows 2000 under Windows 7 Virtual PC not working correctly

  - by dave

  I have just moved my Windows 2000 Virtual PCs from Vista to Windows 7 Professional (64-bit). The machines work to a point but I have found some problems: drive mapping does not seem to work any more. I need this to exchange data. I do not need network access to the virtual PC so would rather leave it unconnected. the virtual PC would automatically shutdown the session and go to the login screen after a few minutes of inactivity. I tried installing the Virtual PC Integration Components but the install failed (one of the messages basically says it's XP+ only). Now I'm stuck in 640x480 mode with mouse capture. I have heard that you can install an older version of the Integration Components but this sounds a bit suspect. Does anyone have any ideas on how to get Windows2000 working with drive sharing on a Virtual PC?

  Read the article

• Ubuntu 10.04 recognizing USB 2.0 external HD as USB 1.1

  - by btucker

  When I connect the USB 2.0 drive I see this: usb 1-4.3: new full speed USB device using ohci_hcd and address 5 so I know it's getting seen as USB 1.1. usb-devices shows that it really is USB 2.0 and connected to a USB 2.0 hub: T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 2 Spd=12 MxCh= 4 D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=05e3 ProdID=0608 Rev=77.61 S: Product=USB2.0 Hub C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub T: Bus=01 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=13fd ProdID=1340 Rev=02.10 S: Manufacturer=Generic S: Product=External C: #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=2mA I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage It seems the problem is that root hub is: T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh=10 D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1d6b ProdID=0001 Rev=02.06 S: Manufacturer=Linux 2.6.32-25-server ohci_hcd S: Product=OHCI Host Controller S: SerialNumber=0000:00:02.0 C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub And there's no mention of ehci_hcd. lsusb -t gives me: /: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=ohci_hcd/10p, 12M |__ Port 4: Dev 2, If 0, Class=hub, Driver=hub/4p, 12M |__ Port 2: Dev 4, If 0, Class=stor., Driver=usb-storage, 12M |__ Port 3: Dev 5, If 0, Class=stor., Driver=usb-storage, 12M |__ Port 6: Dev 3, If 0, Class=stor., Driver=usb-storage, 12M It seems like I'm missing something which would allow the OS to see USB 2.0 devices. Can anyone point me in the right direction? EDIT Full lsusb -v output: Bus 001 Device 005: ID 13fd:1340 Initio Corporation Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x13fd Initio Corporation idProduct 0x1340 bcdDevice 2.10 iManufacturer 1 Generic iProduct 2 External iSerial 3 57442D574341595930323337 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 32 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xc0 Self Powered MaxPower 2mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 8 Mass Storage bInterfaceSubClass 6 SCSI bInterfaceProtocol 80 Bulk (Zip) iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x02 EP 2 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 0 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0001 Self Powered Bus 001 Device 002: ID 05e3:0608 Genesys Logic, Inc. USB-2.0 4-Port HUB Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 0 Full speed (or root) hub bMaxPacketSize0 64 idVendor 0x05e3 Genesys Logic, Inc. idProduct 0x0608 USB-2.0 4-Port HUB bcdDevice 77.61 iManufacturer 0 iProduct 1 USB2.0 Hub iSerial 0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 100mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0001 1x 1 bytes bInterval 255 Hub Descriptor: bLength 9 bDescriptorType 41 nNbrPorts 4 wHubCharacteristic 0x00e0 Ganged power switching Ganged overcurrent protection Port indicators bPwrOn2PwrGood 50 * 2 milli seconds bHubContrCurrent 100 milli Ampere DeviceRemovable 0x00 PortPwrCtrlMask 0xff Hub Port Status: Port 1: 0000.0100 power Port 2: 0000.0103 power enable connect Port 3: 0000.0103 power enable connect Port 4: 0000.0100 power Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 1 Single TT bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0001 Self Powered Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 0 Full speed (or root) hub bMaxPacketSize0 64 idVendor 0x1d6b Linux Foundation idProduct 0x0001 1.1 root hub bcdDevice 2.06 iManufacturer 3 Linux 2.6.32-25-server ohci_hcd iProduct 2 OHCI Host Controller iSerial 1 0000:00:02.0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0002 1x 2 bytes bInterval 255 Hub Descriptor: bLength 11 bDescriptorType 41 nNbrPorts 10 wHubCharacteristic 0x0002 No power switching (usb 1.0) Ganged overcurrent protection bPwrOn2PwrGood 1 * 2 milli seconds bHubContrCurrent 0 milli Ampere DeviceRemovable 0x00 0x00 PortPwrCtrlMask 0xff 0xff Hub Port Status: Port 1: 0000.0100 power Port 2: 0000.0100 power Port 3: 0000.0100 power Port 4: 0000.0103 power enable connect Port 5: 0000.0100 power Port 6: 0000.0103 power enable connect Port 7: 0000.0100 power Port 8: 0000.0100 power Port 9: 0000.0100 power Port 10: 0000.0100 power Device Status: 0x0003 Self Powered Remote Wakeup Enabled

  Read the article

• Wake computer from sleep/standby without BIOS support for WOL?

  - by jjeaton

  Just bought a new home server and the nice folks at HP disabled the Wake-On-Lan feature in my motherboard. Are there any other options for waking the computer from Sleep/Standby mode? I'd like to take advantage of power savings wherever I can. I realize that I won't be able to wake it from shutdown, short of putting together some Rube Goldberg machine. EDIT: I'd like to be able to wake the machine on demand, remotely. So I can then RDP into it, or access files, etc.

  Read the article

• PostgreSQL 9.1 on Ubuntu Lucid fails to start - how to debug?

  - by Tom Fakes

  I'm using Vagrant with Chef Solo to setup a Lucid 64 box. I'm using a Chef recipe to install PostgreSQL 9.1 from Martin Pitt's backports. The install goes ok until the point where the database is started with /etc/init.d/postgresql start There's a log pause and the command fails. If I run pg_ctl manually, the database starts! The entire contents of my postgresql-9.1-main log file is: 2012-05-07 11:01:18 PDT LOG: database system was shut down at 2012-05-07 11:01:16 PDT 2012-05-07 11:01:18 PDT LOG: database system is ready to accept connections 2012-05-07 11:01:18 PDT LOG: autovacuum launcher started 2012-05-07 11:01:18 PDT LOG: incomplete startup packet 2012-05-07 11:01:26 PDT LOG: received fast shutdown request 2012-05-07 11:01:26 PDT LOG: aborting any active transactions 2012-05-07 11:01:26 PDT LOG: autovacuum launcher shutting down 2012-05-07 11:01:26 PDT LOG: shutting down 2012-05-07 11:01:26 PDT LOG: database system is shut down I've tried to change the postgresql config file to get more info into the logfile, but that hasn't worked at all. How do I debug this to find out what is failing so I can fix it?

  Read the article

• Not able to login to new AMI on EC2 - moveing from micro to small instance

  - by zengr

  I had a t1.micro instance (old_server) on Linux on EC2 and now I need to upgrade my server to m1.small Linux (new_server). So, here is what I did: Shutdown old_server and create an AMI. Launch the new AMI with m1.small configuration. (I kept the key and security group same as old_server) I tried to login by: ssh -i my_key.pem [email protected] But, it gives a connection timeout error. My login to old_server works fine. So, my question is: What is the correct way to scale up (vertically) an EC2 instance? Where am I going wrong in the above mentioned step? When I create an AMI in step 1, is the EBS (data) also copied.

  Read the article

• VirtualBox CPU usage 100% on host

  - by Sarveshwar

  I have installed VirtualBox 3.1.2 (latest) on my Windows 7 (x64). In the VirtualBox I've installed Windows 7 (x64). I have 4 GB RAM installed. The guest has been assigned a 1536 MB RAM. Sometimes the CPU usage on the host goes 100%. It happens everytime, in a few minutes, after starting the guest. Then it stops responding. Then I have to "power off the machine" from the menu without doing a proper shutdown. It happens with Windows XP as guest too (even when the RAM amount assigned to it was the same). What is the problem?

  Read the article

• EMC CX3-10c Fault Condition won;t clear

  - by ITGuy24

  We have an old CX3-10c from Dell that had both Standby Power Supplies (SPS) fail. This obviously caused a fault on the system and disabled the cache. We have replaced the SPS's and they test fine as do all other components. Problem is there is still a fault on the "Enclosure SPE [SPE3]" despite all the component in the enclosure showing as good. I was on the line with Dell Gold support for 3 hours yesterday, they have had me restart the SPs multiple times, as well as reseat the power supplies, even shutdown the system completely and power it back on. All to no avail. Fault remains and cache cannot be re-enabled so long as the Fault is present. Any suggestions on clearing this erroneous fault?

  Read the article

• How to start wuala on the linux commandline with auto login

  - by mit

  When i start wuala on the linux commandline like this, it logs me in and the folder is mounted: wualamcd login username password enableAutoLogin I can shut it down from another console typing wuala shutdown But how do I actually use the auto login that I just set using the enableAutoLogin switch? What is the command to start it again, so it logs in but does not need the password? I tried wualamcd login and wuala starts but no one gets logged in. Auto login in gui mode works fine. This is 32 bit linux with openjdk 6 JRE.

  Read the article

• what Windowx XP LAN driver for Asus F5Z

  - by Radek

  a friend of mine asked me to re-install his Asus F5Z notebook with Windows XP. I installed succcessfully all drivers from assus driver download site. Everything is working fine but ethernet driver. The installation of Lan Driver for WIN XP finishes with strange message "Please shutdown & plug Realtech PCI-e card to complete the installation. Not sure if it matters but OnChip SATA is in 'Native IDE' mode . The original one with Vista was 'IDE - AHCI mode'. Any idea how I can make the LAN adapter to work under Windows XP?

  Read the article

• Unresponsive virtual OS

  - by confusedGeek

  Hopefully someone has a suggestion on how to resolve this. Configuration Host: Win 2003R2 w/Virtual Server 2005R2 Virtual1: Win 2003R2 w/Sql Server 2005 Virtual2: Win 2003R2 w/WSS 3.0 Situation This past weekend the power went out and took down the servers (no UPS, it's a desktop standing in as dev testing server). Since the servers went down the Virtual2 server after running WSS fairly heavily for an hour to two will become unresponsive via HTTP. If I login via virtual server's remote control I don't get anything beyond a background screen. The CPU counter on the virtual server's master status shows that it isn't doing anything. The only thing I have been able to do is to turn off Virtual2, which loses any state changes. Shutdown commands issue from the virtual server master status are ignored. After restarting Virtual2 the event logs and application logs don't indicate what caused the problem. Anyone have an idea as to how to repair the OS, or maybe what could be the problem? Thanks ahead of time.

  Read the article

• Can't boot into Linux partition after installation

  - by Otto

  I just installed Ubuntu. I created a partition in MacOSx using Disk utility, then deleted the partition and installed Ubuntu on the free space created. After the installation, Ubuntu said it would reboot. I hang on shutdown (which is normal, as google told me), so I used the power button to turn the MacBook off. Now I want to boot into Ubuntu. Pressing option/alt on startup only shows me the MacOSx and Windows partition. Also, the Linux partition isn't showing up on my MacOSx desktop. And in Disk Utility, I can see 3 grayed out partitions: "disk0s4", "disk0s5" and "Linux Swap". What can I do to boot into Ubuntu without losing my other partitions? Thank you for your help.

  Read the article

• Is there anyway to stop Windows 8 from restarting for an update?

  - by William Hilsum

  My Windows 8 machine is going to restart shortly... I have tried a few techniques such as shutdown /a which is not having much luck. Short of pausing the Windows Update service, is there anyway to stop this restart from happening? ---update--- Looks like the "restart" is all talk and no action! The time has gone and I am presented with this: So, it goes along with the top answer here (which I shall shortly accept) --- update again--- It did reset!!! My battery went critical and it turned itself off, I turned it back on (out of suspend) when it was plugged in, I logged in and the first thing it did was automatically restart - closing my open tabs in Chrome :( Oh well...

  Read the article

• MS-DOS 7.1, Active-Boot

  - by user3005255

  I created a MS-DOS 7.1 (Win 98) active-boot USB-flash stick and it functions properly. Nevertheless I still have some unsolved issues: I want to change my keyboard-layout to german but I don´t know where to start since I only have the "basic-DOS" with IO.sys, MSDOS.sys + command.com. I already created Autoexec.bat + config.sys but don´t know which files I need and which I have to change in order to get a german keyboard. Also I can´t really shutdown my DOS properly, what is the right way to do it in MS-DOS 7.1? Thanks very much in advance for your help!

  Read the article

• Old laptop turns off due to overheating

  - by Jake Thomas

  I have an old Laptop that powers off when the processor's temperature exceeds 84degs Celsius. The more annoying part is flash causes this the most of the times. If I watch a web feed for more than 15-20mins, it results into hard shutdown of the machine. I have an idea of a could-be solution to this problem, I want a program that would decrease the processor's clock speed to about 1.2GHz or whatever, leading it a lower temperature. Is there a program out there that does this? P.S. Someone please edit this and add the relevant tags, as I'm new and i have no idea of what tags to choose from.

  Read the article

• Creepy MySQL error during hard work

  - by Kiewic

  Hi, I have a MySQL database installed on a OpenSuse 11.1 server (it is a Bitnami image). The database works fine, it can stay many days without any error, but when MySQL receives a huge amount of transactions, it dies immediately. The next screen shows the error: Moreover, I don't know how to restart MySQL. I have tried this: /opt/bitnami/mysql/bin/mysqld start But it doesn't work, that gives me the next output: 110209 17:09:01 [ERROR] Fatal error: Please read "Security" section of the manual to find out how to run mysqld as root! 110209 17:09:01 [ERROR] Aborting 110209 17:09:01 [Note] /opt/bitnami/mysql/bin/mysqld.bin: Shutdown complete It doesn't matter which kind of statements are executing, if they are a huge amount, MySQL dies. The MySQL server version is 5.1.30 What can be causing these sudden failures?

  Read the article

• Windows 7 freezing unexpectedly

  - by Thomas Deutsch

  I have a Windows 7 computer here, which is freezing between 2 times a day and 1 time every second day. I see no problem, no special drivers, no special Apps are open, no encryption or something like that. Apps usually open then are Firefox, Thunderbird, Eclipse and maybe Office. Computer is just freezing. No Reboot, no shutdown, no bluescreen and no error. User has to hardreset it. Eventlog shows me an kernel error saying it has been unexpected rebooted due to an fatal error, but no statement about what kind of error happended. Anyone an idea what it can be? Chkdisk should be ok (currently, I run it a second time).

  Read the article

• Redundant APC UPS units, single server set up

  - by Sholom

  Hi All We have a very simple set up, looking for a very simple (reliable) solution: Setup: One Dell box with redundant power supplies running Windows 2003, plugged into two separate APC SmartUPS 1500 units (USB, no smart cards) on two separate circuits. Solution required: IF (UPS1 = Low) AND (UPS2 = Low) THEN: Shutdown gracefully ELSE: DO NOTHING!! APCUPSD only allowes for one instance (and therefore one UPS) in a windows environment. PowerChute can't do this without using APC Smart Cards which means utilizing our switch, but the switch does not have redundant power supplies, so it will only live for as long as one of the two UPS units. And no, i don't have the budget to buy two smart cards pluse a switch with redundancy ;) Thanks

  Read the article

• how to copy sql server database on same server

  - by Sam

  I've got a SQL Server 2008 and want to make a copy of a database so I've got a 2nd Version of the database for testing on the same server. The database copy wizard is not able to copy the database, it always sends funny error Messages about missing objects (using SMO copy). When I try to make a backup and restore it under a different database name it still keeps the file names of the original database and overrides this (crashing the original database). So how do I copy a SQL database? Shutdown SQL Server, copy the physical files and attach them? Maybe a command line tool for database copy? Shouldn't there be an easy way to make a copy?

  Read the article

• What is the command to use to put your computer to sleep (not hibernate)?

  - by airrick

  I want to put my windows pc (win7) into a sleep state via command line (so i can bind to macro button on keyboard). The power button on the PC is setup to but the computer to sleep (but it's down on the floor and I'm too lazy to reach down) it exactly how I want it (sleeps using hybrid mode in case I loose power) The sleep command on the shutdown menu also works. most info I found says to use; %windir%\system32\rundll32.exe PowrProf.dll, SetSuspendState 0,1,0 But this puts the computer in hibernate mode. I do have hibernate disabled but using hybrid sleep. So, What is the command to use to put your computer to sleep (not hibernate)?

  Read the article

• Could today's windows update have caused boot problems?

  - by gjvdkamp

  I have a 64 bit box that is dual boot Windows 7 64bit and Ubuntu. I booted into windows today and saw the 'updates ready' sign on the shutdown button so I clicked to let it install. It took a while to install 2 updates. Then I rebooted but now it doesn't get past the motherboard splash screen. So I don't even get the disks found messages or let alone the prompt to choose windows or Linux. Cold this be caused by the updates? Seems weird for a windows patch to have consequences beyond the windows os, but it seems unlikely to be a coincidence Thanks, Gert-jan

  Read the article

• Dual HDD dual boot Win7/Win7 hibernate corrupts partitions?

  - by Ivan Zlatev

  I have two SSDs in my laptop. Both have 2 partitions each one with Windows 7 64bit and another one with OEM stuff on it (SYSTEM_DRV). I use the BIOS boot menu to boot between the drives. I have removed the drive letters so that no partitions of drive 1 are mapped in windows 2 on drive 2 and wise-versa. What I have observered however is that when I hibernate windows 1, boot windows 2 do some work and shutdown then resume windows 1 - the windows 2 partition will get corrupt quite often. Just happened actually - it is shown as "RAW" in the Disk manager instead of NTFS and windows will blue screen at boot. Alternatively I've seen cases where chkdsk will run and will wipe out all security descriptors making the partition completly unbootable. Why am I seeing these corruptions and what can I do to prevent them?

  Read the article

• Server 2008 unresponsive after SP2 install.

  - by Dan

  I have a dev server that has an exact image of a production web server. The prod server only has SP1 installed on it. When I first fired up the dev box, the first thing I did was install SP2, and let it be. Almost every morning when I came in, the server was unusable. It would respond to ping, but RDP and the web site running on it were down. On the screen the screen saver was bouncing around, so it wasn't hard locked. But it was unresponsive to keyboard and mouse. So now I have to hard shut it down, but when it comes back up, the only thing in the event viewer is the unexpected shutdown, nothing else. I've since taken a fresh image of my prod box and put it on the dev server, and not installed SP2, and the dev box is humming along perfectly. I should also note that this is Server2k8 Web, 64bit Has anyone else seen anything like this?

  Read the article

• How to integrate monit into web app deployment process

  - by shabunc

  I have: Tomcat with webapp deployed via mvn tomcat:redeploy. Monit, pinging the host and restarting server if ping failed. The thing is there in a moment during the redeployment when ping will fail - and this is normal, actually. So, the question is - what is the best way to teach monit to consider the fact of redeployment and not to confuse it with "real" black outs. This is of course an issue of balance between elegance, ease of implementation and scalability. The most straightforward solution I can think of - is just to shutdown monit before deployment and start it up after once again. But this if far from elegance I guess.

  Read the article

• View rotated log files Mac OS X Server (*.?.gz)

  - by Meltemi

  Trying to look at some of our older log files and find they're cryptic "Unix Executable Files". This particular server I'm working with is an older Mac OS X Server (10.4 - Tiger). -rw-r----- 1 root admin 36 1 Jun 15:48 wtmp -rw-r--r-- 1 root admin 578 27 May 17:40 wtmp.0.gz -rw-r----- 1 root admin 89 26 Apr 13:57 wtmp.1.gz -rw-r----- 1 root admin 78 29 Mar 16:43 wtmp.2.gz -rw-r----- 1 root admin 69 15 Feb 17:21 wtmp.3.gz -rw-r----- 1 root admin 137 16 Jan 13:09 wtmp.4.gz i'm using zless to try and view the contents of the .gz files. and what i see is unreadable: ... <DF>^R<AF>ttyp1^@^@^@joe54^@^@^@^@^@108.184.63.22^@^@^@^@K<DF>"<B8>ttyp1^@^@^@^@^@ ^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@K<DF>%<A1>console^@^@^@^@^@^@^@^@^@ ^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@^@K<E0>1 ~^@^@^@^@^@^@^@shutdown^@^@^@^@^@^@^@^@ ^@^@^@^@^@^@^@^@K<E0>1^L~^@^@^@^@^@^@^@reboot^@^@^@^@^@^@ ... same goes for system.log.0.gz, etc... anything that's been rolled in compressed .gz files. What am i missing?

  Read the article

< Previous Page | 206 207 208 209 210 211 212 213 214 215 216 217  | Next Page >