Search Results

Search found 8976 results on 360 pages for 'wcf rest'.

Page 210/360 | < Previous Page | 206 207 208 209 210 211 212 213 214 215 216 217  | Next Page >

• Windows 7 Default Gateway problem

  - by Matt

  I have a strange problem (or at least seems strange to me) the below are IP configurations for two laptops on my home network which consists of a main router 192.168.11.1 and a connected wireless router (i know this can cause problems but has always worked until I got the win7 machine) at 192.168.11.2 with DHCP disabled. Laptop 1 - Win XP IP: Dynamically assigned by main router default gateway: 192.168.11.1 (main router) This machine gets perfect connectivity. Laptop 2 - Win7 IP: dynamically assigned by main router Default Gateway: 192.168.11.2 THIS IS THE PROBLEM... I cannot seem to get this machine to default to the main router for the gateway UNLESS I go to a static configuration which I would rather not do since I regularly go between my home and public networks. Why is my Win7 machine not finding the main gateway the same way that the other laptop is? I believe that the rest of my setup is fine as it has always worked and it works perfectly when set as static ip and gateway. Please help! Thanks

  Read the article

• Disadvantages of enabling AHCI after Win7 install

  - by Mario De Schaepmeester

  I've formatted my notebook that has a 5400RPM HDD with ~500GB capacity. After installing Windows 7 and about half the drivers (including chipset) I began to doubt whether to go for IDE or AHCI mode for my hard drive. There used to be a lot of discussion on the internet which is better and so far I understood it was particularly helpful on SSDs. Now the general consensus seems to be that AHCI mode is best for most hard drives. I have thus enabled AHCI in the middle of configuring my notebook (rest of the drivers, necessary software etc...) Two questions: considering my HDD's spec above, should I leave it on? Is there any disadvantage of enabling it after Windows 7 and chipset drivers installation? Windows 7 version is 64 bit Home Premium.

  Read the article

• Clicks or ticks every minute when HDD is idle [closed]

  - by Ramy

  Possible Duplicate: Clicks or ticks every minute when HDD is idle My HDD is a My passport... It's 2 weeks old. I hear this tick or click followed by another one about 8-9 secs later, and they repeat every minute almost exactly... They usually happen and the LED light blinking.. It's not like the other clicks you hear that indicate any inevitable HDD failure, it's much lower in volume. I don't know what that is, however it's different than the rest of the HDD usual sounds...It's close to the sound of the mouse click. It sometimes also happens when I access a file on the drive mostly after being idle for a while, sometimes randomly not really sure... The drive though is working well, the SMART report comes out OK and without warning, and disk management shows it healthy... What could be the cause of this??

  Read the article

• The mobile application cannot connect to the web service

  - by cancelledout

  Hello everyone. I have a mobile app webservice client that connects to a WCF webservice(on my PC) deployed in a WiMo Device. The OS is Windows Mobile 6.0. It is connected to my PC using a USB cable and ActiveSync 4.5. Problem: When I use a mobile emulator to run the application, it was able to connect to the web service successfully. But if I use the mobile phone to run the application, it cannot connect to the web service. However, I can view the webservice's test webpage using phone's browser(IE) (http://153.xxx.xxx.xxx:8080/Design_Time_Addresses/SOAP11demo/Service1/) Can you guys help me identify on what is wrong?

  Read the article

• Making a hidden truecrypt volume with existing data

  - by Bill Grey

  I have a 1TB hdd, which I would like to encrypt. I would like to make a hidden volume, with almost nothing within but some decoy data, and the rest in a hidden volume. However, my driver is over 95% full. Is it still possible to do this, or would it have to be done on an empty drive, and then copy the data over? I could not find the answer to this question in the documentation. Also, how easy would it be to undo, or unencrypt the drive? Would it again need another empty drive to begin with?

  Read the article

• Should we create Virtual Machine environment so a consultant can develop in similiar environment?

  - by ChrisNel52

  This is a large project and currently there are only 3 developers working on it. We have some money in the budget to contract development help from a software consulting firm. However, because the location of our business it would be beneficial if the consultant could do their development off-site. Also, our company policy doesn't allow contract help to VPN into our network, so that is not an option. My question is, would it be a good idea to create a Virtual Machine that copies our internal environment (particularly our database and WCF service) and give the consultant the Virtual Machine image so that they can replicate the environment at their place of work? I haven't worked much with Virtual Machines, so I'm not sure if this is a good idea or if there are huge obstacles that I'm not thinking of. If anyone has ever done anything like this, it would be great to hear the pros/cons. Any help would be appreciated.

  Read the article

• ASP.NET MVC, JSON & non JavaScript clients

  - by redsquare

  I need to ensure that an application I am developing is accessable and also works with JavaScript turned off. I just need a pointer to assist with the following. I had 3 'chained' select boxes and I wanted JavaScript enabled clients to have a nice Ajax experience. I can easily write the required functionality to populate the chained boxes on the change event of the preceeding select using jQuery and JSON with a WCF service. However what about the non JavaScript client? Would I wrap a submit next to the select and place these inside their own form to post back with a certain action or different querstring parameter? Can the same controller give me a partial JSON response as well as feeding the full HTML response. Can anyone point me to a good demo that utilises both JSON and normal HTTP posts to produce the same result in ASP.NET MVC. All ASP.NET MVC demo/examples I see forget about the non JavaScript enabled client.

  Read the article

• PRNG test suite: bitstream and stream length

  - by Martin Trigaux

  On the NIST website, there is a tool called sts (Statistical Test Suite) that allow us to rest the validity of a pseudo-random number generator based on a stream of bits in input. When running the program, there is two variables I am not sure to understand : the stream length and number of bitstream. Is the stream length the size of the file ? The number of bit inside ? The size of a bitstream ? Are the bitstreams subset of the whole file ? Chosen how ? Let say I have a text file containing 1,000,000 bits in ascii. What should be my arguments ? You can find the user manual here if needed (I didn't find explanation about what are these variables in it). Thank you

  Read the article

• API server not function ["The connection has been reset"]

  - by Miguel Beltrán

  I'm having some troubles with one of my servers. I've done an application with two servers, one the frontend that grabs the data of server API (Ubuntu server). Well, yesterday had a lot of visits and the API server stop functioning but: -I can do stuff in MySQL by SSH. -The memory usage is ok. -The logs are ok. -The bandwitch usage is ok. -If i restart the server or Apache2, function by some time (3-4 minutes). And the most important i think if i tries to access to API (Is rest-style with http) it puts me the Firefox error "The connection has been reset". I'd tried: -Restart the server -Restart Apache2 -Restart MySQL -Viewed the logs of Apache2/MySQL I don't know too much about systems so i don't know what to do more.

  Read the article

• How to get Gmail/browser to remember login?

  - by Jay

  I am using firefox 3.6.22. I have several Gmail accounts. In the past, when I would go to the Gmail login, it would remember all my logins. All I would need to do would be to enter first letter and it would pick up the rest. Now it has stopped doing this. I can still type the whole login (if I remember it) and the password and get in. Why did it lose the ability to remember, and how do I get it back?

  Read the article

• Nhibernate.Bytecode.Castle Trust Level on IIS

  - by jack london

  Trying to deploy the wcf service, depended on nhibernate. And getting the following exception On Reflection activator. [SecurityException: That assembly does not allow partially trusted callers.] System.Security.CodeAccessSecurityEngine.ThrowSecurityException(Assembly asm, PermissionSet granted, PermissionSet refused, RuntimeMethodHandle rmh, SecurityAction action, Object demand, IPermission permThatFailed) +150 System.RuntimeTypeHandle.CreateInstance(RuntimeType type, Boolean publicOnly, Boolean noCheck, Boolean& canBeCached, RuntimeMethodHandle& ctor, Boolean& bNeedSecurityCheck) +0 System.RuntimeType.CreateInstanceSlow(Boolean publicOnly, Boolean fillCache) +86 System.RuntimeType.CreateInstanceImpl(Boolean publicOnly, Boolean skipVisibilityChecks, Boolean fillCache) +230 System.Activator.CreateInstance(Type type, Boolean nonPublic) +67 NHibernate.Bytecode.ActivatorObjectsFactory.CreateInstance(Type type) +8 NHibernate.Driver.ReflectionBasedDriver.CreateConnection() +28 NHibernate.Connection.DriverConnectionProvider.GetConnection() +56 NHibernate.Tool.hbm2ddl.SchemaExport.Execute(Action`1 scriptAction, Boolean export, Boolean justDrop) +376 in IIS configuration service's trust level is Full-trust also application's web config's trust level is full. how could i make this service in working state?

  Read the article

• Best method to cleanly shut down an application launched via another.

  - by JYelton

  I couldn't find any close answers to this, so I'm consulting the experience of SO users: Scenario: I have two small C# winforms applications where one behaves as a server or host, the other as a client. They share data via SQL Server, in terms of configuration settings. I am currently launching the client application (which only needs to run periodically) from the server application via Process.Start() and terminating it via Process.CloseMainWindow() (after finding it in the process list). While it seems clean enough, I wondered if there's a better way. Question: Which way would be best to instruct the client application to shut down: Continue using Process.CloseMainWindow()? Implement WCF between the applications? (I would need help on how to do this.) Set a variable in SQL that the client application checks for? Some other way?

  Read the article

• HTTP Caching Server that supports POST

  - by Jeroen

  I am hosting a REST service which is sending appropriate cache-control headers. I use Varnish as a caching server in front of my webserver. However, a limitation of varnish is that it doesn't support caching HTTP POST and HTTP PUT. Is there any alternate caching server that will be able to cache these requests? I understand that caching POST is a bit tricky because you cannot just cache based on the url as a key like for GET; it needs to actually inspect the request body. In case of multipart/form-data requests, there should probably be a limit on the size of the request body for it to be cached (so that big file uploads, etc won't be cached). Nevertheless I really want to be able to cache short HTTP POST, or at least the application/x-www-form-urlencoded ones.

  Read the article

• Detect whether certain IIS features are present from InstallScript

  - by Christian Hayter

  I have an InstallScript project written in InstallShield 2010, which, amongst other things, shells out to several .NET MSI installers that install web apps. If any of these web apps are selected for installation by the end user, I need to check for the following optional IIS features from InstallScript code before allowing the install to proceed: ASP.NET (IIS 6+) WCF HTTP Activation (IIS 7+) IIS Metabase and IIS 6 configuration compatibility (IIS 7+) Can anyone point me in the right direction please? Ideally I'm looking for registry values that I can check directly from InstallScript code, but I guess some kind of WMI or COM check would be OK as well. PS: In case it's relevant, we need to support all versions of IIS from 5.1 onwards at this time. If 5.1 support is a problem, we may consider dropping it if we have to.

  Read the article

• Best Technologies for AJAX Web Development

  - by floatingfrisbee

  Hey Everyone, I have some experience in AJAX development, mostly on .NET and MooTools. However, I want to learn more and see what others out there thought about the various other options available. I am looking more for advise about the front end. The back end, I will most probably be coding up in .NET using c# and WCF services. Please feel free to provide me as much information as you can. Also I would appreciate any links to resources. List of Options (feel free to add) Write my own Javascript Use a frame work like MooTools, JQuery etc. Which one is better? Use Google Web Toolkit. Am I tying myself to limitations of GWT? Or are there not limitations? ASP.NET AJAX WPF (Will this run on non IE browsers?) Flash (it'll be a pain to learn action script) Thanks Jaspreet

  Read the article

• Raid recovery in gigabyte GA-8I945 Pro

  - by epeleg

  This was a working machine until a few days ago. And now it won't boot into the OS, during startup if makes clicking sounds (I think from one of the drives). Installed OS: Windows 2003 Web edition Hardware: Gigabyte GA-8I945P Pro , 2*160G Sata in RAID1 configuration , 2 Volumes – 25G and the rest. When I installed windows on it, during setup, I pressed F6 and used ICH7DH drivers of RAID. The manual for the MOBO says: Step 1: After the POST memory test begins and before the operating system boot begins, look for a message which says "Press to enter Configuration utility" (Figure 4). Press CTRL+ I to enter the RAID BIOS setup utility. But the machine never shows this message. BIOS SATA RAID/AHCI Mode is set to RAID. Any ideas or pointers on what I can do to recover my data? Thanks

  Read the article

• md5sum of large files gives different results sometimes

  - by Emanuele

  I have an AMD quad core, 8 gb RAM, 1 SSD EXT2 (2 months old), 2 HDD EXT4, approximately 1 year old. I'm using Ubuntu 10.04 x86-64 and when I compute the md5sum of large files (9 GB) sometimes I get different values than the one stored on a reference file. Upon restarting and switching off the PC then I get the expected results no matter how many times I repeat it. But this is random. I've turn on ECC (the fastest possible settings) and the issue seems to be rarer, but I've run memtest86+ for 6+ hours without a glitch (and with ECC off!). Any idea? Should I update the BIOS of my motherboard (Asus EVO-something...don't remember it now)? I've tried all the rest apart this, but genuinely don't know what to do anymore... Any suggestion is appreciated!

  Read the article

• Cloning a linux system from sdx to cciss

  - by churnd

  I have an HP ML 310 server running CentOS Linux 5.5. I'm buying a RAID card (LSI 9260-8i) to set up a mirrored OS drive. Right now, the boot drive is set up with GRUB installed on the MBR of /dev/sda & has a 100MB /boot partition for /dev/sda1, then the rest is configured in LVM with a 20GB with a 20GB VG for the root partition & ~80GB VG for home. The new disk sizes will also be slightly larger as well. What is the best way to clone the boot drive to the new CCISS device?

  Read the article

• How to have a soft-real-time process in presense of heavily swapping IO-intensive background load?

  - by Vi

  schedtool: PID 32301: PRIO 4, POLICY R: SCHED_RR , NICE -20, AFFINITY 0xf ionice: realtime: prio 4 But the music is stumbling anyway. Background load is low prio (SCHED_IDLEPRIO, idle ionice), but uses a lot of memory (more than is physically available) and does a lot of IO and calculations. Latencytop shows about 1500ms for: Following symlink Writing buffer to disk (sync) Page fault Writing a page to disk both for the bg load and for unrelated processes. Load average is 10 and counting. Why cannot it allocate, for example, 200MHZ of one of the cores and 32M of memory and not less than once per second opportunity for IO for mplayer to make it happy while continuing calculations on the background? Or: why it cannot leave background task and swap loving each other but keeping the rest of the system as if there were no background load? How to have RT processes AND heavy bg load simultaneously (without of virtual machines)?

  Read the article

• Inbound connections using Internet Connection Sharing in Apple/Mac/Leopard

  - by tlianza

  I have a Mac mini which I'm using to give some other devices wireless access, by sharing it's Airport connection with the local ethernet, and that is plugged into a switch. All devices can get online no problem. (See how: http://www.macosxhints.com/article.php?story=20041112101646643 and http://www.macosxhints.com/article.php?story=20071223001432304 ) The issue is that I need to be able to connect in to these machines as well (at least, for the Slingbox to work). All the devices have 192.168.2.* addresses, and the rest of my local network is on 192.168.1.*. I tried setting a static route so that the 192.168.2.* addresses would use a gateway of 192.168.1.50 (my mac mini's address) but that didn't seem to help. Does anyone know if what I'm trying to do is possible? I admit I'm not certain what Internet Connection sharing is really doing under the hood... perhaps it just does basic nat, and doesn't do the type of routing I'm looking for. If so, anyone know if this is possible?

  Read the article

• how to write silverlight threading function in another file or project

  - by Piyush

  I am using three tier architecture.I have SilverlightUI and UIController two projects.SilverlightUI contains only UI pages and controls while UIController contains all proxies of WCF services. Now I have created threads to update my controls dynamically and to do processing parallel.AS the requirement I want to define all functionality of threads in UIController projects.What should I do? Currenty what I am doing - private void Button_Click(object sender, RoutedEventArgs e) { StartThreads(); } private void StartThreads() { private Thread _thread1; _thread1 = new Thread(DoThread1); _thread1.Start(); } public static void DoThread1() { _data1.Dispatcher.BeginInvoke(delegate() { _data1.Text = _count1.ToString(); }); System.Threading.Thread.Sleep(1000); } I Want to write DoThread1() method in UIController project and call that function from here button_click()

  Read the article

• Keyboard doesn't work after Windows resume from sleep (S3) -- how to fix?

  - by Marco Z

  I have a weird issue with my keyboard after resuming from S3 sleep: I can type perfectly for maybe 5 seconds, but afterwards the keyboard ceases to work until I hibernate or restart (or sleep again -- see below.) The rest of my system runs just fine -- just the keyboard apparently "freezes" up. Some closer observations: The keyboard will work for 5 seconds (and freeze again) every time I resume from sleep, even if it was frozen from a previous sleep The caps lock light will work fine within the 5 seconds. But after the keyboard "freezes", the light will remain on, but I'll be unable to turn it off. Perhaps this means power wasn't cut off from the keyboard, but it's just some software freezing up the port??? Given this info, would this indicate a problem with Windows itself? Drivers, maybe? Can I rule out the BIOS as the culprit? Finally, any ideas on how to fix? Thanks! Specs: Windows 7 x64 HP tx1000 laptop

  Read the article

• backup and file server for 50+ TB of data

  - by a-bomb

  our office wants to build a new server to handle our data, over the last 10 years our data was stored on CDs, DVDs, HDDs but now they want all of it in one place that is attached to the network for everybody in the office to access it. the data is 20TB new data and the rest is old, the important now is to store these 20tb and gradually store the other 30tb over time. so what is the best solution to do ? we thought of getting an hp server and connect it to an external enclosure that either had tape drives or HDDs (we haven;t decided yet) or to get a NAS server and connect it to the hp server. what should we do because this is new for us ...

  Read the article

• Out Of Memory Error - Magento

  - by robobobobo

  Ok normally I understand when my server is giving me out of memory errors, but this one has me stumped! I'm running a magento based site, with one or two plugins in it and the rest is pretty basic. The site runs and loads fine wiht no issues. However in the backend - Configuration - Payment Methods it gives me the following out of memory error Fatal error: Out of memory (allocated 39059456) (tried to allocate 85 bytes) in ########/Varien/Simplexml/Element.php on line 84 Now this is where I'm confused..it's allocated more than it tried to allocate? Am I correct there? So how is it running out of memory? My server has 6Gb ram, an SSD and 2 CPU's running WHM with a few other low traffic sites on it. I set my php memory limit to 100mb, 1000mb and finally unlimited but all to no avail! I'm completely lost here, would really appreciate some expertise on this Cheers

  Read the article

• sizes of RAM, of virtual memory and of swap for 32-bit OS

  - by Tim

  If I understand correctly, a 32-bit OS (Ubuntu) can only address 4GiB memory, so RAM with size larger than 4Gib will only be used 4Gib of itself and the rest is a waste. I am now confused about this situation for RAM with similar one for virtual memory and for swap. with virtual memory being swap + RAM, if the size of the virtual memory exceeds 4Gib, will the exceeding part be a waste for the 32-bit OS? if I now have to choose the size for my swap partition, is it a factor to consider that the 32-bit OS can only address 4GiB memory? Does the size of swap have to be chosen with respect to the 4Gib addressible limitation? Will the swap exceeding 4GiB always be a waste? is virtual memory equal to RAM and swap? or can virtual memory use space on the hard drive outside the swap partition? Thanks and regards!

  Read the article

< Previous Page | 206 207 208 209 210 211 212 213 214 215 216 217  | Next Page >