Search Results

Search found 40420 results on 1617 pages for 'power line networking'.

Page 212/1617 | < Previous Page | 208 209 210 211 212 213 214 215 216 217 218 219  | Next Page >

• OpenVPN/Tunnelblick through wireless router, no connection.

  - by Oscar

  I'm using OpenVPN with Tunneblick on my Macbook Pro to access a server on my job. I't works fine, but i can't get it working with my Netgear WGT624v3 wireless router. I get this warning: WARNING: potential route subnet conflict between local LAN [192.168.1.0/255.255.255.0] and remote VPN [192.168.1.0/255.255.255.0] Someone told me that i should "port forward" on my router, but i can't figure out the right settings. Also not shure i'm doing it right.

  Read the article

• Are same IP address with different submask unique?

  - by xEnOn

  In a same block of IPv4 addresses, can there be same IPs with different submasks? For example, can I have this: 180.70.65.140/26 180.70.65.140/25 180.70.65.140/24 All the 3 addresses above have the same numbers but different subnet mask. Are all the 3 addresses distinct of their own? In other words, 180.70.65.140/25 belongs to User A, 180.70.65.140/25 belongs to User B and 180.70.65.140/24 belongs to User C? After applying the submask, their network addresses look like this: 180.70.65.140/26 --> 180.70.65.128/26 180.70.65.140/25 --> 180.70.65.128/25 180.70.65.140/24 --> 180.70.65.0/24 If the addresses are recognised uniquely, how is it so? How would each of the these addresses being recognised to be unique? I am thinking like once I have 180.70.65.140/26, I can't reuse the same numbers of 180.70.65.140 again but since classless is meant to increase the number of IP addresses, it would do much if I can't reuse.

  Read the article

• "Request not supported" in IPCONFIG (WinXP SP3)

  - by pablog

  In a customer PC (Windows XP SP3), suddenly the network went down: the network adapter appears with an error mark. I replaced the network card, but the new one does the same thing. When I enter IPCONFIG, XP shows this error (in standard and safe mode): Internal error occurred Request not supported Unable to query host name If I start the system with a boot cd the PC runs fine, so the problem seems to be in the XP installation. I tried: uninstalling and reinstalling the network card in the Device Manager disabling and reenabling the card netsh int ip reset netsh winsock reset catalog and a couple of "reset" programs (WinsockxpFix.exe, etc) with no luck. Is there any way to fix it without reinstalling XP? TIA, Pablo

  Read the article

• Force an LXC container to use its own IP address

  - by emma sculateur

  Sorry if this question has already been asked. I could not find it, I have this setup : +---------------------------------------------------------------------------------------------+ |HOST | | | | +-------------------------------------------------+ | | | UBUNTU-VM | | | | | | | | +-------------------+ | | | | |UBUNTU-LXC | | +------------------+ | | | | 10.0.0.3/24 | 10.0.0.1/24 | |OTHER VM | | | | | eth0-----lxcbr0----------eth0-----------br0----------eth0 | | | | | | 192.168.100.2/24| 192.168.100.1/24 |192.168.100.3/24 | | | | +-------------------+ | +------------------+ | | +-------------------------------------------------+ | +---------------------------------------------------------------------------------------------+ When I ping 192.168.100.3 from my UBUNTU-LXC, the source IP address is automatically changed to 192.168.100.2 by UBUNTU-VM. It's like having a NAT, whereas I really want my UBUNTU-LXC to talk with it own IP address. Is there any way to do this ? Edit : these info may be relevant : I am using KVM +libvirt to set up my VMs Here is how I create my interface in UBUNTU-VM : <interface type='bridge'> <mac address='52:54:00:cb:aa:74'/> <source bridge='br0'/> <model type='e1000'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x09' function='0x0'/> </interface>

  Read the article

• Smoothwall Express interface issues

  - by Timbermar

  I have a SmoothWall Express box that is currently configured with a Green and Purple interface. Both interfaces are in the same /24 subnet (which seems odd to me). The green interface (address of .254) has a DHCP server that is pushing addresses from .1 to .100 and the purple interface (.253) is pushing addresses from .101 to .120. Every machine here is trusted, and as such is connected to the green interface via a wired connection or wireless APs. Nothing is connected at all (port is physically empty, traffic graphs show no activity) to the purple interface. However, every machine here is pulling addresses from the purple interface. So the question boils down to, how do I remove/stop my machines from pulling from the purple dhcp interface? Also, shouldn't the purple interface (if we were using it for guest Wifi or something) be on a different subnet (i.e. 192.168.100.0/24 instead of 192.168.1.0/24 with all the trusted machines)?

  Read the article

• Which subnet masks are valid for a subnetted Class B address?

  - by Daddy Warbox

  Yes, this is a school question, and yes I already know the correct possible answers (supposedly), so I'm not going to bother posting them. Instead, I just want to understand the meaning of this question. I know what class B addresses are, and what valid class B subnet addresses are. I guess one way to define my question is to ask why the answer "255.255.0.0" is wrong, necessarily? That seems to defy my understanding, or else some part of my brain is just not registering the question correctly. Thanks in advance.

  Read the article

• MSI netbook refuses to connect to home wireless network with Windows XP

  - by sa125

  I'm trying to connect my girlfriend's MSI netbook to the wireless network in my house, and failing repeatedly. It's not a hardware issue, b/c it connects to other networks successfully, and, it's not a network issue, because I have another mac and linux laptops that have no problem detecting and connecting to the same network. When I open windows' network connections box, I can see the network available, and when I try to connect to it (using a password), I get a "network no longer in range.." error (the router is 2 ft away). This has been the case for the past 6 months, and I'm about to give up. I've reset the router, erased all saved network preferences and pretty much all I could think of short of re-installing XP. Any idea what else could be done? thanks.

  Read the article

• How to Hide OS Fingerprint of Virtual Machine?

  - by Jeremy Battle

  Is it possible to make a linux virtual machine appear as the host machine to a network tool like nmap or Blue's Port Scanner without recompiling the kernel?

  Read the article

• Sharing a printer over the net from Windows 7 to Windows Server 2003

  - by Grant Unwin

  Hi, I need to share a printer that is connected to a Windows 7 computer. The windows 7 computer is in another building about an hours drive away. The computer that needs to access the printer is running Windows Server 2008. Ive tried setting the printer as 'shared' for 'everyone' on the Windows 7 PC and accessing it from the server by adding a TCP/IP port to the IP address but the printer just wont add. From googling aparently it may need setting up as a printer server through IIS, but i'm just not sure on the best practice. Any help greatly appreciated. Thanks Grant Unwin

  Read the article

• Planning home network

  - by gakhov

  I'm planning to setup my home network from scratch and want to ask professional opinions or tips. My home is connected to Internet with a cable connection (100 Mb/s). The devices I would like to connect are VoIP phone (RJ-45), TV (WiFi/LAN), 3 laptops (WiFi), 2 smartphones (WiFi), an iPad (WiFi), a Kindle (WiFi), a network printer and, probably, a home media storage (WiFi/LAN). As you can see, the most load will be on WiFi connections (probably, even if TV supports WiFi it's better to connect it by LAN?). So, I need help to choose the best router (or combination of routers) to support stable connections for all these devices and minimize the total number of routers/adapters. I like how Cisco/Linksys devices were working for me in the past, so preferably (but not obligatorily) I want to setup network with their solutions. Any thoughts?

  Read the article

• wi-fi connection drops periodically for a few seconds

  - by sergiom

  I've read the similar question on wireless connections dropping, but no answer seems to apply to my case I have configured the wi-fi lan of my router to broadcast sid and use WPA-PSK. Every few minutes my wi-fi connection drops for a few seconds and then restores. When I use two computers and run a ping -n 50000 on both computers, I see that the connection drops at different times but with almost the same rate. the router is a zyxel, one pc runs windws vista and uses a USB wi-fi device from Belkin: F6D4050 the other one runs windows 7 is a Dell PC with an Intel(R) WiFi Link 5100 AGN there are no other wi-fi lans around

  Read the article

• External routing for local interfaces in a virtualized network

  - by Arkaitz Jimenez

  Current setup: br0| |-- tun10 -pipe-tun0(192.240.240.1) |-- tun11 -pipe-tun1(192.240.240.2) |-- tun12 -pipe-tun2(192.240.240.3) The pipe program is a custom program that forwards data back2back between two tun interfaces. The idea is puting 2 programs in .2 and .3 while keeping .1 as the local interface in the current machine. The main problem is that I want to route packets to .2 and to .3 through .1 and br0, but as they are local interfaces, the kernel ignores any routing instruction, it just delivers the packet to the proper interface. Tried iptables, but the nat table doesn't even see ping packets to those ifaces. A "ping 192.240.240.2" delivers a icmp packet with source and dest .2 to tun1, ideally it should deliver a source .1 dest .2 at tun1 through tun0-br0-tun1 Any hint? Here the output of some commands: Output

  Read the article

• msi netbook refuses to connect to home wireless network (windows xp)

  - by sa125

  Hi - I'm trying to connect my girlfriend's MSI netbook to the wireless network in my house, and failing repeatedly. It's not a hardware issue, b/c it connects to other networks successfully, and, it's not a network issue, because I have another mac and linux laptops that have no problem detecting and connecting to the same network. When I open windows' network connections box, I can see the network available, and when I try to connect to it (using a password), I get a "network no longer in range.." error (the router is 2 ft away). This has been the case for the past 6 months, and I'm about to give up. I've reset the router, erased all saved network preferences and pretty much all I could think of short of re-installing XP. Any idea what else could be done? thanks.

  Read the article

• What's the best solution for file sharing in my case? DAS or NAS?

  - by jakub

  I want to have in my network small, cheap and energy efficient server with will be fully customizable (Gnu/Linux, OpenBSD). What is more I want to have big, redundant storage in my network and access to it via server. I have already small terminal without hard drive (no SATA/PATA, one drive on USB) which works fine. I don't want to buy big server, or to use regular computer for that. It's not cheap. I thought about a small case (ITX?), and cheap computer in this with SATA ports, but I cannot find anything interesting :( I thought about NAS in network and server independently and booting server from NAS, I'm not sure which technologies will be good for that, and I don't know what with performance. Direct connection to NAS through network from workstation is next pro for that. What do you think about DAS? It will be good for that?

  Read the article

• I've inherited a rat's nest of cabling. What now?

  - by hydroparadise

  You know, you see pictures like below and sort of chuckle until you actually have to deal with it. I have just inherited something that looks like the picture below. The culture of the organization does not tolerate down time very well, yet I have been tasked to 'clean it up'. The network functions as it is, and there doesn't seem to be rush to get it done, but I will have to tackle the bear at some point. I get the ugly eye when I mention anything about weekends. So my question goes, is there sort of a structured approach to this problem? My Ideas thus far: Label, Label, Label Make up my patch cables of desired length ahead of time Do each subnet at a time (appears that each subnet are for different physical locations) Replace one cable at a time for each subnet It's easier to get forgiveness than permision?

  Read the article

• How to stop Windows 7 from automatically connecting to unsecure wifi network

  - by Remi Despres-Smyth

  One of my neighbors has an unsecure wifi network called WLAN. At one point in the past, I accidentally connected to it, and disconnected immediately when I noticed. Now, when I open my laptop at home, it sometimes connects to the WLAN network first, before trying my (secured) home wifi network. The information I've found regarding this issue seems to suggest this network should have a profile on the "Manage wireless networks" screen - but it does not. How do I tell Windows 7 to never connect to networks with SSIDs called WLAN? Or to never connect to unsecured networks without confirming with me first?

  Read the article

• Any software that draws my network layout?

  - by claws

  Hello, I'm looking for some tool on windows/linux which draws the layout of the network I'm in. Btw, don't think I'm just a user in this network. I don't have any admin controls.

  Read the article

• Weighted round robins via TTL - possible?

  - by Joe Hopfgartner

  I currently use DNS round robin for load balancing, which works great. The records look like this (I have a ttl of 120 seconds) ;; ANSWER SECTION: orion.2x.to. 116 IN A 80.237.201.41 orion.2x.to. 116 IN A 87.230.54.12 orion.2x.to. 116 IN A 87.230.100.10 orion.2x.to. 116 IN A 87.230.51.65 I learned that not every ISP / device treats such a response the same way. For example some DNS servers rotate the addresses randomly or always cycle them through. Some just propagate the first entry, others try to determine which is best (regionally near) by looking at the ip address. However if the userbase is big enough (spreads over multiple ISPs etc) it balances pretty well. The discrepancies from highest to lowest loaded server hardly every exceeds 15%. However now I have the problem that I am introducing more servers into the systems, that not all have the same capacities. I currently only have 1gbps servers, but I want to work with 100mbit and also 10gbps servers too. So what I want is I want to introduce a server with 10 GBps with a weight of 100, a 1 gbps server with a weight of 10 and a 100 mbit server with a weight of 1. I used to add servers twice to bring more traffic to them (which worked nice. the bandwidth doubled almost.) But adding a 10gbit server 100 times to DNS is a bit rediculous. So I thought about using the TTL. If I give server A 240 seconds ttl and server B only 120 seconds (which is about about the minimum to use for round robin, as a lot of dns servers set to 120 if a lower ttl is specified.. so i have heard) I think something like this should occour in an ideal scenario: first 120 seconds 50% of requests get server A -> keep it for 240 seconds. 50% of requests get server B -> keep it for 120 seconds second 120 seconds 50% of requests still have server A cached -> keep it for another 120 seconds. 25% of requests get server A -> keep it for 240 seconds 25% of requests get server B -> keep it for 120 seconds third 120 seconds 25% will get server A (from the 50% of Server A that now expired) -> cache 240 sec 25% will get server B (from the 50% of Server A that now expired) -> cache 120 sec 25% will have server A cached for another 120 seconds 12.5% will get server B (from the 25% of server B that now expired) -> cache 120sec 12.5% will get server A (from the 25% of server B that now expired) -> cache 240 sec fourth 120 seconds 25% will have server A cached -> cache for another 120 secs 12.5% will get server A (from the 25% of b that now expired) -> cache 240 secs 12.5% will get server B (from the 25% of b that now expired) -> cache 120 secs 12.5% will get server A (from the 25% of a that now expired) -> cache 240 secs 12.5% will get server B (from the 25% of a that now expired) -> cache 120 secs 6.25% will get server A (from the 12.5% of b that now expired) -> cache 240 secs 6.25% will get server B (from the 12.5% of b that now expired) -> cache 120 secs 12.5% will have server A cached -> cache another 120 secs ... i think i lost something at this point but i think you get the idea.... As you can see this gets pretty complicated to predict and it will for sure not work out like this in practice. But it should definitely have an effect on the distribution! I know that weighted round robin exists and is just controlled by the root server. It just cycles through dns records when responding and returns dns records with a set propability that corresponds to the weighting. My DNS server does not support this, and my requirements are not that precise. If it doesnt weight perfectly its okay, but it should go into the right direction. I think using the TTL field could be a more elegant and easier solution - and it deosnt require a dns server that controls this dynamically, which saves resources - which is in my opinion the whole point of dns load balancing vs hardware load balancers. My question now is... are there any best prectices / methos / rules of thumb to weight round robin distribution using the TTL attribute of DNS records? Edit: The system is a forward proxy server system. The amount of Bandwidth (not requests) exceeds what one single server with ethernet can handle. So I need a balancing solution that distributes the bandwidth to several servers. Are there any alternative methods than using DNS? Of course I can use a load balancer with fibre channel etc, but the costs are rediciulous and it also increases only the width of the bottleneck and does not eliminate it. The only thing i can think of are anycast (is it anycast or multicast?) ip addresses, but I don't have the means to set up such a system.

  Read the article

• My DNS cannot resolve an web site address?

  - by ipkiss

  Hello all, Recently, I could not access the webpage bbc.co.uk anymore, while I can access other websites smoothly. Ar first, I though there may be some problem with my laptop. However, if I use my laptop through my company network, I can load the page bbc.co.uk normally. Then, I though maybe my ADSL at home blocks that web address. However, I tried another laptop with my home ADSL and it can load the page bbc.co.uk very fast. Now I do not know what could be the problem. Can anyone tell me please? Thank you.

  Read the article

• TCP Tweaking options and Results: Any suggestions?

  - by krishnakumar

  I first tried with the default windows XP TCP option(It doesn't have TCPWindowSize option and TCP1323 in its Registry setting). I dynamically set those options using TCP optimizer. Here I list out the result with and without TCP Tweaking option. I see no major improvements in TCP after increasing window size optimally too. What value should I set to increase the performance? Results: Without any window size and MTU setting from server to client (receiving) TCPWindowSize : MTU : TTL: Size:586 MB total duration : 03:47 With window size extension from server to client (receiving) Bandwidth :100 Mbps Latency: 100ms BDP :1250000 TCPWindowSize : 1250000 MTU :1500 TTL:128 Size:586MB total duration : 03:44 With window size extension from server to client (receiving) TCPWindowSize :64240 MTU :1500 TTL :112 Size: 586MB total duration : 03:49

  Read the article

• How to setup a Wi-Fi 2-computer network with Internet sharing?

  - by Narek

  I have the following devices: Desktop Computer (Windows XP Professional) Laptop Computer (Windows Vista Home Premium) A USB modem that I want to connect to my Desktop computer (so my Desktop has Internet) And a Wi-Fi router (D-Link, model: DIR-300) that I want to use in order to create a connection between mentioned two computers to be able to share files and what is the most important thing to make my laptop to have access to the Internet. What steps I should do to have this system?

  Read the article

• Command line import of database using latin1 encoding

  - by chrisjlee

  I'm using a particular cloud hosting solution (one which i won't name) and they don't provide ssh access so i'm at a whim on how the database is dumped. I downloaded the dump which is packed into a tar.gz file. I discover that this file utilizes latin1 encoding. Which i don't get to specify the encoding for the host i'm using because i don't have SSH access or DB access. I try to import it via command line for my local development environment (mysql -uroot foodb < file.db) like i usually do with other databases but am having problems. Is it possible to import a database via command line by specifying which encoding (preferably latin1) before importing it? Or do i have to convert it to UTF8?

  Read the article

• How to bypass vpn talking to VMWare Guest?

  - by marc esher

  Greetings. Network/VPN n00b question here. I'm running VMWare Workstation with a Guest Windows 2003 Server. It has SQL Server 2000 installed. The sole purpose for this Guest is to house SQL Server... it needn't have internet access or access to any other resources on the network other than the host. When launch Check Point VPN software, the host routes through the company network before it connects to the guest ... i.e. it's no longer a direct connection. I assume this is just how things are supposed to work. However, what's happening is that the connection between my host and the SQL Server instance on the guest intermittently drops. It's not consistent, and some databases on the server will be responsive while others aren't. It appears that the databases with the most traffic on the guest (the ones I'm hitting with load tests) are the ones that become intermittently unresponsive. This problem only manifests when VPN is on; when it's off, I can pound away on this database with no troubles. Thanks for any advice!

  Read the article

• Downstream to server periodically dropping and spiking

  - by dauphic

  I have a server located in Canada. I'm experiencing that, when connecting from the south-eastern US (southern California, Arizona), I see my downstream on connections to this server periodically drop to 0 for 1-3 seconds, then spike in the next second and receive all of the data that should have been received during the drop off period. This doesn't happen in regular intervals, but it does happen often, usually once every 5-10 seconds. I've gotten trace routes from users with various ISPs and locations, but I'm not seeing any spikes or drop offs in response times, or any sort of packet loss. I'm guessing this is because ICMP is prioritized, though. It seems like a misbehaving router along the way, but I have no idea how to figure out where the problem lies (let alone if there's any way to work around it). Is there any way for me to diagnose this problem?

  Read the article

• Cannot access firewalled jboss server from Internet Explorer

  - by Simon Gibbs

  I've produced a website for a client One Single Menu using JBoss and hosted it on Rackspace Cloud Servers running Ubuntu's Maverick Meerkat. Following advice, I esablished some iptables rule to protect jboss: iptables -I INPUT 1 -i lo -j ACCEPT iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A INPUT -p tcp --dport 22 -j ACCEPT iptables -t nat -A PREROUTING -p tcp --dport 80 -j REDIRECT --to-port 8080 iptables -I INPUT -p tcp --dport 8080 -j ACCEPT iptables -t nat -A OUTPUT -o lo -p tcp --dport 80 -j REDIRECT --to-port 8080 iptables -A INPUT -j DROP Now, several versions of IE on several computers on at least two different ISPs cannot access the onesinglemenu.com. Curl from within the datacenter, Firefox, and Safari on the same ISPs can all access the server fine. I even tried IE and Firefox on the same computer and IE failed but Firefox worked. The error behaviour is that IE hangs on connecting without reporting an error, even after a minute or so. No page is displayed at all. I find it quite odd that I'm having a browser specific connection issue, but it appears to be the case. Help!

  Read the article

< Previous Page | 208 209 210 211 212 213 214 215 216 217 218 219  | Next Page >