Search Results

Search found 7738 results on 310 pages for 'calling convention'.

Page 214/310 | < Previous Page | 210 211 212 213 214 215 216 217 218 219 220 221  | Next Page >

• Periodic internet connection drops

  - by sterlingholt

  My setup is a dsl modem, and a dlink di 524M router. I'm also using a Witopia VPN which runs through OpenVPN. I've been having trouble with the internet connection dropping very frequently. It comes back shortly, without even a router/modem/computer restart. This happens as frequently as every ten minutes. Occasionally (not often) it will last as long as an hour or two without dropping. When it drops, I can get it back almost immediately by clicking Reconnect in the OpenVPN GUI and letting that do it's thing. It's worth noting that I'm in China. Calling support is a bit difficult because of that. Also I don't really understand all of the router's software, although I've got it generally figured out. I've tried a bunch of stuff, attempts to diagnose and/or fix the problem. No success with any of the following: I've power cycled both the modem and the router. I've tried an ethernet connection to the router. I've connected without the VPN. I've disabled IEEE authentication on all connections. I've checked for viruses. I've tried lifting it off the ground so as to prevent overheating.

  Read the article

• What program sent which packet to the network [closed]

  - by Erik Johansson

  I would like to have a tcpdump like program that shows which program sent a specific packet, instead of just getting the port number. This is a generic problem I've had on and off sometimes when you have and old tcpdump file lying around you have no way to find what program was sending that data.. The solution in how i can identify which process is making UDP traffic on linux ? is an indication that I can solve this with auditd, dTrace, OProfile or SystemTap, but doesn't show how to do it. I.e. it doesn't show the source port of the program calling bind().. The problem I had was strange UDP packets, and since those ports are so short lived it took me a while to solve this issue. I solved this by running an ugly hack similar to: while true; date +%s.%N;netstat -panut;done So either a method better than this hack, a replacement for tcpdump, or some way to get this info from the kernel so I can patch tcpdump. EDIT: This was asked on superuser "tracking what programs sends to net", no good solution though.

  Read the article

• Has anyone else experienced page fault crashes with Snow Leopard on MacBook Pro?

  - by BruceMartin

  I bought a Macbook Pro computer on Sept 3rd from MacMall. As I was using it to learn Snow Leopard (this is my first Mac, I am a long time Windows developer), it would crash every one or two hours. After calling Apple support, I dropped it off at the Apple store for diagnostic testing and repair. WhenI picked up the computer from Apple, they told me that it did not crash while they had it. They suspected a software problem, so they had done a fresh install of Snow Leopard for me. At home I went through the start up procedure with the newly installed Snow Leopard. Then I downloaded the iPhone SDK, and the computer crashed again while I was away waiting for the download to finish. I was using a USB mouse, which was the only device attached. No other software installed. I was presented with a dump that mentions terms like "panic", Kernel trap", and "page fault". Does anyone have any idea what this problem might be? I really can not use this MacBook under these circumstances.

  Read the article

• How do I restrict the Open/Save dialog in Windows to one folder?

  - by MindModel

  I spend a significant amount of time helping non-techies use their PC's. I realized most of that time is spent trying to explain to them how the Windows folder hierarchy works, where the "open file" dialog is pointing now, and how to find that Word document they saved. All this time, they're telling me they "just want to print the file". They refuse to learn how to read the PC screen, try to memorize a fixed set of steps, and end up calling me back to tell me their files disappeared again. I realize it's not productive to try to restrict where PC apps (e.g. Quicken) store files. But if there was a Windows utility I could turn on or off that would restrict the Open/Save dialogs in Windows apps, my noob user friends and I would save an enormous amount of time. The goal would be to have all files whose locations are chosen by the Save dialog saved to one folder, and have the Open dialog always point to that folder, until the utility is turned off. Does such a Windows utility exist?

  Read the article

• python mysqldb - mysql server gone away - can't reconnect

  - by david.barkhuizen

  When attempting to import a bunch of data into mysql tables using python and mysqldb, I run into the following error '2006 - mySQL Server has gone away', and then I am unable to reconnect again within the script. I am iniitially re-using a connection object across transactions ( delineated by conn.commit() ), then when I first encounter this exception, if I create a new connection by calling MySQLdb.connect(), this new connection also fails with the same exception. This error does not occur immediately, I can pump a fair amount of data into the db, but then faithfully occurs after I have inserted a couple thousand records, so roughly once the db has committed a certain transaction volume, it always falls over like this. If I rerun the script, WITHOUT restarting the db server. then it resumes where it left off, pumps in some data, then falls over again. Before recommendations to change time-out timings, does anyone know why I am not able to establish a new connection after the initial failure ? - Even if I try a couple of times waiting a couple of seconds between each. (btw, I'm running Windows 7, mysql server 5.1.48, mysqldb 1.2.3.gamma.1, python 2.6)

  Read the article

• Howto change Axis server-config.wsdd so that we don't expect a SOAPAction

  - by GKForcare

  The problem I'm facing is that the client of my service will never send me a SOAPAction header. How can I tell Axis to still map to the incomming call to my service implementation anyway. I did bump into tricks like adding a Handler like this: <handler name="ReportMapper" type="java:com.mycompany.project.ReportMapper"/> <transport name="http"> <requestFlow> <handler type="ReportMapper"/> <handler type="URLMapper"/> <handler type="java:org.apache.axis.handlers.http.HTTPAuthHandler"/> </requestFlow> <parameter name="qs:list" value="org.apache.axis.transport.http.QSListHandler"/> <parameter name="qs:wsdl" value="org.apache.axis.transport.http.QSWSDLHandler"/> <parameter name="qs.list" value="org.apache.axis.transport.http.QSListHandler"/> <parameter name="qs.method" value="org.apache.axis.transport.http.QSMethodHandler"/> <parameter name="qs:method" value="org.apache.axis.transport.http.QSMethodHandler"/> <parameter name="qs.wsdl" value="org.apache.axis.transport.http.QSWSDLHandler"/> </transport> but that did not help. The mapper is found during the creation of the WSDL but when calling the service, the invoke of the handler is not used. I do need to note that when I simulate the SOAP-call using @curl@ and I do add the SOAPAction header, the invoke is called. Any help would be most appreciated.

  Read the article

• Cant kill process on Windows Server 2008!! - Thread in Wait:Executive State

  - by adrian

  I hope someone can help me with our issue we are having. We have a major issue with a process that we can not kill and the only way to get rid of the process is to reboot the machine. I have tried killing it from the normal task manager but no joy. I have tried killing it using the taskkill /F command from a command prompt and no joy. The command reports as sucessful but the process remains. I have tried to start task manager with system rights by calling "psexec -s -i -d taskmgr" and attempting to kill the process but no joy I have tried killing it from Process Explorer but again the process remains. I have tried creating a scheduled task that runs under the SYSTEM name to kill the task but that also does not kill it : schtasks /create /ru system /sc once /st 13:16 /tn test1 /tr "taskkill /F /PID 1576" /it Nothing I do will kill this process. Even logging off and logging back on will not kill this process. Using Process Explorer I notice that there is on stubborn thread that is in the Wait:Executive state. I have tried to kill this thread using Process Explorer but again no joy. We are using Windows Server 2008 R2 64-Bit. The server is brand new and windows is freshly installed. Now heres the thing. We have brought two identical servers from Dell with the same specs and the same OS installed and I can not replicate this issue on the other server. Only on this server, under certain circumstances does this server process hang and can not be restarted! I have also changed the compatability mode by setting it the process to "Windows 2003" but this has not helped. I have noticed in Process Explorer that DEP is turned on but im not sure this has got any bearing on the issue ot not. Please, can someone help??

  Read the article

• General name for Macs' operating system

  - by andy124

  First of all, I hope that my question is fairly suitable for this site. I have a website where I would like to write articles about some operating systems. Therefore, I have created a main category called "Operating systems". Within a subcategory, I would like to write articles about Apple's operating system that is running on Macs. However, I do not know what to name this category. I have always thought the name was just OS X, but come to think about it, the "X" is actually part of the version (10). Therefore I cannot exactly call my category OS X, because what about when OS 11 is released in a few years? And since Apple has gone from Mac OS X to just OS X, then I cannot use "Mac OS". And, if I remove the X from OS X, then I only have "OS" left, which does not seem so proper. I am really looking for a meaningful all-round name for the Macs' operating system that does not involve the versioning. I was thinking about just calling the category "Mac", but that is not precise either - but perhaps the closest I can get?

  Read the article

• How to display escaped characters in tmux status bar

  - by walrus

  i am running tmux from a tty on an embedded linux device. (NOT a terminal emulator) because the screen is rather small, i want to add some "icons" to the tmux status bar. to achieve this, i have simply created a font with the appropriate glyphs for things like battery, or wifi. i can load the font, and display the characters with calls that use an escape to the line drawing characters like so: echo -e "\xe\234\xf" \xe escapes me into line drawing character mode, \234 is my created character, and \xf returns me to normal character mode so my terminal doesnt start getting goofy. this works perfectly if i enter the command at the terminal whether tmux is started or not. the issue arises if i then try to use it in my ~/.tmux.conf file for the status bar. i currently have a line like this: set -g status-right "#(echo -e "\xe\234\xf") #(/script/to/output/powerlevel) this simply outputs \xe\234\xf powerlevel this goes the same if i try printf over echo. this is the output i would expect to get on the terminal if i made the call without passing -e to echo, or without enclosing the statement with quotes. i then decided to wrap the calls to the echo or printf in a shell script. again, the script works when called from the terminal, but not in tmux's status bar. now i get the unprintable character "?" instead of my icon, like this: ? powerlevel this is what i would expect if i did not use the line drawing escapes previously mentioned above, or if i tried to copy and paste the character as text using tmux. in addition, the calling of these character scripts screws up the rest of my status-right, as the clock has about 6 digits for minutes when it is called (though it correctly only updates two of them). how can i make tmux respect the escape characters? any help or insight is greatly appreciated.

  Read the article

• Apache reports a 200 status for non-existent WordPress URLs

  - by Jonah Bishop

  The WordPress .htaccess generally has the following rewrite rules: # BEGIN WordPress <IfModule mod_rewrite.c> RewriteEngine On RewriteBase / RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule . /index.php [L] </IfModule> When I access a non-existent URL at my website, this rewrite rule gets hit, redirects to index.php, and serves up my custom 404.php template file. The status code that gets sent back to the client is the correct 404, as shown in this HTTP Live Headers output example: http://www.borngeek.com/nothere/ GET /nothere/ HTTP/1.1 Host: www.borngeek.com {...} HTTP/1.1 404 Not Found However, Apache reports the entire exchange with a 200 status code in my server log, as shown here in a log snippet (trimmed for simplicity): {...} "GET /nothere/ HTTP/1.1" 200 2155 "-" {...} This makes some sense to me, seeing as the original request was redirected to page that exists (index.php). Is there a way to force Apache to report the exchange as a 404? My problem is that bogus requests coming from Bad Guys show up as "successful requests" in the various server statistics software I use (AWStats, Analog, etc). I'd love to have them show up on the Apache side as 404s so that they get filtered out from the stat reports that get generated. I tried adding the following line to my .htaccess, but it had no effect (I'm guessing for the same reason as the previous redirect rules): ErrorDocument 404 /index.php?error=404 Does anyone have a clever way to fix this annoyance? Additional Info: OS is Debian 6.0.4, and Apache version looks to be 2.2.22-3 (hosted on DreamHost) The 404 being sent back to the client is being set by WordPress (i.e. I'm not manually calling header() anywhere)

  Read the article

• LYNC 2010 Dial-In in Meeting DTMF issue

  - by user140116

  We are facing an issue in the LYNC2010 dial-in to a meeting. We redirect an Asterisk number to LYNC, whitch connects successfully in the dial-in plan of LYNC. After calling from external network to the given number, we hear LYNC aswering and prompting us to enter the PIN and afterwards the hash key. I should mention that all other dials to LYNC from Asterisk and vise versa are routed successfully. Also all DTMF we send to Asterisk from the phone (IVR, Extension, PIN etc) are routed also fine Afterwards we press the appropriate pin folowed by the hash keyand we get 'Sorry I can't find meeting with that number' Some pros mentioned that it might be dtmfmode=RFC2833 or dtmfmode=auto in Asterisk (All checked and tried). Some pros mentioned, that there is a problem in geeral in LYNC and DTMF (even with Cisco Call Manager). Some other pros mentioned that chack box 'Enable refer support' in Voice Routinh\Trunk Configuration' in LYNC has to be unchecked (Also tested). The problem stil remains and there is no way to enter a meeting room by dial-in. ANY idea would be appreciated!!!!!!!!

  Read the article

• How to have a shell script available everywhere I SSH to

  - by aib

  I have a shell script which I simply cannot do without: bar from Theiling Online I use SSH a lot and on a variety of *nix servers. However, I am not a system administrator and usually don't have the time or privileges to install it on every server I connect to. It is apparently a very portable sh script and has command line options to export itself as a shell function, which got me thinking: Could I use one of OpenSSH's subjectively obscure features to export it everywhere I go? My first thought was to assign the source to an environment variable like BAR = "cat -v" and then execute it on the other side as `$BAR`, but 1) I can't even get the cat example to to work locally, 2) I don't know how to put the script's actual multiline source into an environment variable and 3) I have yet to see a machine with PermitUserEnvironment enabled. I guess I could even do with an ssh option to write a file called ~/bar at logon, but a more volatile solution would be better. Calling wget http://.../bar at logon would be unacceptable. Any ideas? P.S. Putty-specific solutions, though I doubt any would exist, are also fine.

  Read the article

• Relaying to tech "support" that computer is actually broken.

  - by Sion

  First some background: I have a Dell Inspiron 15R M050, it is still under the Dell limited warranty and the Best Buy Extended warranty. I am currently dual booting Debian Squeeze and Windows 7, the only reason I go into Windows is to play video games specifically steam games. Issue: When I play my games in Windows I am capable of playing for anywhere from 5 minutes to 2 hours before I suffer a hard-lock. I cannot alt-tab, ctrl-alt-delete, ctrl-shift-escape do anything for 2-3 minutes. After this hard-lock period everything runs fine, I can continue the game for probably another hour at least before I suffer another lock. Games: Borderlands, Splinter Cell: Chaos Theory, Starcraft 2, Garrys Mod What I have tried: Running the diagnostic suite in the dell bios, restoring the OEM Windows recovery partition on the HD, fresh installing Windows 7 Professional, updating BIOS, Calling tech support and having them run a software Hardware Diagnostics suite. The question: I think from the research that I have performed that it might be a lack of thermal paste on the CPU, would I be able to go to Best Buy and have them do a hardware diagnostic from the hardware level then have them be able to tell Dell that there is a hardware issue? Or would there be a different problem?

  Read the article

• Losing Windows Authentication intermittently

  - by Mark Robinson

  I'm running a website on IIS6 / Server 2003 which uses Integrated Windows Authentication on a local intranet. I can browse to the site but get intermittent "Object null" errors when calling the following C# code which is called on every request: .... GetUserIdFromPrincipal(User) .... public static string GetUserIdFromPrincipal(IPrincipal principal) { return principal.Identity is WindowsIdentity ? (principal.Identity as WindowsIdentity).User.Value : principal.Identity.Name; } (Apologies for the code sample but was torn between SF and SO but think this is more to do with server config). So as the error is intermittent clearly Windows Auth is working on some level but after navigating around the site for several clicks I get the null reference error meaning IPrincipal is null (I thought this should never be null in ASP.NET). The error only happens on this newly built VM. The code is fine on other machines. Does IIS request the Windows Auth details on each request? What would cause such an intermittent problem? Any help or suggestions would be much appreciated.

  Read the article

• After connecting wlan0 to bridge interface (and then removing it), can't connect to AP

  - by gmonk

  I'm on a laptop running Debian Jessie with kernel 3.13-1-amd64; lspci shows that my wireless NIC + driver is 04:00.0 Network controller: Intel Corporation Wireless 3160 (rev 83) Subsystem: Intel Corporation Dual Band Wireless-AC 3160 Kernel driver in use: iwlwifi This has been working without any problems, until I tried creating a bridge for lxc containers to use. I did the same thing as this person here: How-to set up a network bridge on a laptop for LXC use? -- and ended up having the same problem as this poster did, so I decided to "undo" my actions. This hasn't been successful. Actions taken so far: To configure the bridge: #> ip link add type veth #> iw dev wlan0 set 4addr on #> ifconfig veth0 up #> brctl addbr br0 #> brctl addif br0 wlan0 #> brctl addif br0 veth0 #> ifconfig br0 192.168.0.4/24 #> ifconfig wlan0 0.0.0.0 To "deconfigure": #> brctl delif br0 wlan0 #> brctl delif br0 veth0 #> iw dev wlan0 set 4addr off #> ifconfig veth0 down #> ifconfig wlan0 down #> ifconfig br0 down #> brctl delbr br0 Now, dmesg and /var/log/syslog show repeated attempts at connecting to the AP that was working before, which fail after authentication: May 27 09:16:01 myhostname kernel: [11350.757172] wlan0: authenticate with 00:18:f8:54:a3:d6 May 27 09:16:01 myhostname kernel: [11350.759036] wlan0: send auth to 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:01 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> authenticating May 27 09:16:01 myhostname wpa_supplicant[8946]: wlan0: Trying to associate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:01 myhostname kernel: [11350.762615] wlan0: authenticated May 27 09:16:01 myhostname kernel: [11350.762753] iwlwifi 0000:04:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP May 27 09:16:01 myhostname kernel: [11350.762755] iwlwifi 0000:04:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP May 27 09:16:01 myhostname kernel: [11350.765080] wlan0: associate with 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:01 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: authenticating -> associating May 27 09:16:01 myhostname kernel: [11350.767474] wlan0: RX AssocResp from 00:18:f8:54:a3:d6 (capab=0x411 status=12 aid=0) May 27 09:16:01 myhostname kernel: [11350.767476] wlan0: 00:18:f8:54:a3:d6 denied association (code=12) May 27 09:16:01 myhostname wpa_supplicant[8946]: wlan0: CTRL-EVENT-ASSOC-REJECT bssid=00:18:f8:54:a3:d6 status_code=12 May 27 09:16:01 myhostname kernel: [11350.788475] wlan0: deauthenticating from 00:18:f8:54:a3:d6 by local choice (reason=3) May 27 09:16:01 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associating -> disconnected May 27 09:16:01 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: disconnected -> scanning May 27 09:16:02 myhostname dhclient: DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 14 May 27 09:16:04 myhostname wpa_supplicant[8946]: wlan0: SME: Trying to authenticate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:04 myhostname kernel: [11354.559579] wlan0: authenticate with 00:18:f8:54:a3:d6 May 27 09:16:04 myhostname kernel: [11354.561458] wlan0: send auth to 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:04 myhostname wpa_supplicant[8946]: wlan0: Trying to associate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:04 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> associating May 27 09:16:04 myhostname kernel: [11354.563445] wlan0: authenticated May 27 09:16:04 myhostname kernel: [11354.563631] iwlwifi 0000:04:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP May 27 09:16:04 myhostname kernel: [11354.563633] iwlwifi 0000:04:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP May 27 09:16:04 myhostname kernel: [11354.565727] wlan0: associate with 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:04 myhostname wpa_supplicant[8946]: wlan0: Associated with 00:18:f8:54:a3:d6 May 27 09:16:04 myhostname kernel: [11354.568091] wlan0: RX AssocResp from 00:18:f8:54:a3:d6 (capab=0x411 status=0 aid=9) May 27 09:16:04 myhostname kernel: [11354.569030] wlan0: associated May 27 09:16:04 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associating -> associated May 27 09:16:05 myhostname kernel: [11354.978204] wlan0: deauthenticated from 00:18:f8:54:a3:d6 (Reason: 15) May 27 09:16:05 myhostname wpa_supplicant[8946]: wlan0: CTRL-EVENT-DISCONNECTED bssid=00:18:f8:54:a3:d6 reason=15 May 27 09:16:05 myhostname kernel: [11354.992729] cfg80211: Calling CRDA to update world regulatory domain May 27 09:16:05 myhostname kernel: [11354.995004] cfg80211: World regulatory domain updated: May 27 09:16:05 myhostname kernel: [11354.995005] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) May 27 09:16:05 myhostname kernel: [11354.995006] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995007] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995007] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995008] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995009] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995010] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm) May 27 09:16:05 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associated -> disconnected May 27 09:16:05 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: disconnected -> scanning May 27 09:16:09 myhostname wpa_supplicant[8946]: wlan0: SME: Trying to authenticate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:09 myhostname kernel: [11358.763968] wlan0: authenticate with 00:18:f8:54:a3:d6 May 27 09:16:09 myhostname kernel: [11358.765796] wlan0: send auth to 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:09 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> authenticating May 27 09:16:09 myhostname wpa_supplicant[8946]: wlan0: Trying to associate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:09 myhostname kernel: [11358.769957] wlan0: authenticated May 27 09:16:09 myhostname kernel: [11358.770102] iwlwifi 0000:04:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP May 27 09:16:09 myhostname kernel: [11358.770104] iwlwifi 0000:04:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP May 27 09:16:09 myhostname kernel: [11358.770846] wlan0: associate with 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:09 myhostname kernel: [11358.773358] wlan0: RX AssocResp from 00:18:f8:54:a3:d6 (capab=0x411 status=12 aid=0) May 27 09:16:09 myhostname kernel: [11358.773361] wlan0: 00:18:f8:54:a3:d6 denied association (code=12) May 27 09:16:09 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: authenticating -> associating May 27 09:16:09 myhostname wpa_supplicant[8946]: wlan0: CTRL-EVENT-ASSOC-REJECT bssid=00:18:f8:54:a3:d6 status_code=12 May 27 09:16:09 myhostname kernel: [11358.802187] wlan0: deauthenticating from 00:18:f8:54:a3:d6 by local choice (reason=3) May 27 09:16:09 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associating -> disconnected May 27 09:16:09 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: disconnected -> scanning May 27 09:16:12 myhostname wpa_supplicant[8946]: wlan0: SME: Trying to authenticate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:12 myhostname kernel: [11362.573442] wlan0: authenticate with 00:18:f8:54:a3:d6 May 27 09:16:12 myhostname kernel: [11362.575270] wlan0: send auth to 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:12 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> authenticating May 27 09:16:12 myhostname wpa_supplicant[8946]: wlan0: Trying to associate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:12 myhostname kernel: [11362.580334] wlan0: authenticated May 27 09:16:12 myhostname kernel: [11362.580503] iwlwifi 0000:04:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP May 27 09:16:12 myhostname kernel: [11362.580516] iwlwifi 0000:04:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP May 27 09:16:12 myhostname kernel: [11362.583508] wlan0: associate with 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:12 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: authenticating -> associating May 27 09:16:12 myhostname wpa_supplicant[8946]: wlan0: Associated with 00:18:f8:54:a3:d6 May 27 09:16:12 myhostname kernel: [11362.585908] wlan0: RX AssocResp from 00:18:f8:54:a3:d6 (capab=0x411 status=0 aid=9) May 27 09:16:12 myhostname kernel: [11362.586781] wlan0: associated May 27 09:16:12 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associating -> associated May 27 09:16:13 myhostname kernel: [11362.947693] wlan0: deauthenticated from 00:18:f8:54:a3:d6 (Reason: 15) May 27 09:16:13 myhostname wpa_supplicant[8946]: wlan0: CTRL-EVENT-DISCONNECTED bssid=00:18:f8:54:a3:d6 reason=15 May 27 09:16:13 myhostname kernel: [11362.973461] cfg80211: Calling CRDA to update world regulatory domain May 27 09:16:13 myhostname kernel: [11362.975673] cfg80211: World regulatory domain updated: May 27 09:16:13 myhostname kernel: [11362.975675] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) May 27 09:16:13 myhostname kernel: [11362.975676] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975677] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975678] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975678] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975679] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975679] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm) May 27 09:16:13 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associated -> disconnected May 27 09:16:13 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: disconnected -> scanning May 27 09:16:14 myhostname NetworkManager[13992]: <warn> Activation (wlan0/wireless): association took too long. May 27 09:16:14 myhostname NetworkManager[13992]: <info> (wlan0): device state change: config -> failed (reason 'no-secrets') [50 120 7] May 27 09:16:14 myhostname NetworkManager[13992]: <info> Marking connection 'Auto myaccesspoint' invalid. May 27 09:16:14 myhostname NetworkManager[13992]: <warn> Activation (wlan0) failed for connection 'Auto myaccesspoint' May 27 09:16:14 myhostname NetworkManager[13992]: <info> (wlan0): device state change: failed -> disconnected (reason 'none') [120 30 0] May 27 09:16:14 myhostname NetworkManager[13992]: <info> (wlan0): deactivating device (reason 'none') [0] May 27 09:16:14 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> disconnected The things that jump out at me are "deauthenticating ... by local choice( reason=3)" and the lines that contain "(reason=15)". I've tried various fixes: iwconfig wlan0 power off killing wpa_supplicant connecting with iwconfig + dhclient instead of gnome's network -manager explicitly configuring wlan0 in /etc/network/interfaces creating a /etc/wpa_supplicant.conf file ...but nothing seems to work. I'm not sure what I did wrong, or what step I've skipped in trying to get wlan0 back as a non-bridged device -- I removed it from the bridge and then deleted the bridge itself. Any ideas?

  Read the article

• Flash drive suddenly died. Why? Can I recover it?

  - by mg

  Hi, I have a flash drive that I used not too much but, after few month of inactivity, it died. I know that flash drives have a limited write cycles but I am sure that this is not the problem. I tried to create a new partition table and format the drive nothing worked. This is the output of mkfs.ext2. marco@pinguina:~$ sudo LANG=en.UTF-8 mkfs.ext2 -v -c /dev/sdc1 [sudo] password for marco: mke2fs 1.41.11 (14-Mar-2010) fs_types for mke2fs.conf resolution: 'ext2', 'default' Calling BLKDISCARD from 0 to 4001431552 failed. Filesystem label= OS type: Linux Block size=4096 (log=2) Fragment size=4096 (log=2) Stride=0 blocks, Stripe width=0 blocks 244320 inodes, 976912 blocks 48845 blocks (5.00%) reserved for the super user First data block=0 Maximum filesystem blocks=1002438656 30 block groups 32768 blocks per group, 32768 fragments per group 8144 inodes per group Superblock backups stored on blocks: 32768, 98304, 163840, 229376, 294912, 819200, 884736 Running command: badblocks -b 4096 -X -s /dev/sdc1 976911 badblocks: Input/output error during ext2fs_sync_device Checking for bad blocks (read-only test): done Block 0 in primary superblock/group descriptor area bad. Blocks 0 through 2 must be good in order to build a filesystem. Aborting.... Is there something I can do to recover it?

  Read the article

• MySQL getting stuck, eating up disk i/o

  - by bonez05

  Hi all, Using mySQL 5.0.51 on Solaris . At intermittent times it looks like MySQL is getting 'stuck' . The disk usage on the server spikes to 98% busy from reads. I used dtrace (specifically DTrace toolkit - iosnoop) to track down what processes was using all the reads. Mysql was calling tablename.TDM hundreds of times per second. There was no more than average load on the webserver that could account for this. There were no cronjobs running, and no other utilities like mysqldump or anything. It is a master / slave replication setup. As a jury-rigged fix, I altered the mysql table from 'tablename' to 'tablename2' and then back to 'tablename' This fixed the problem temporarily, and "unsticks" mysql. The disk usage goes back down and dtrace is no longer showing hundreds of reads to 'tablename.TDM' / second. A couple ideas I had are: 1. MySQL version bug 2. Infinite loop somewhere in my application (which i'm not sure how likely this is) 3. ?? Has anybody seen this before or have any insight? Thanks

  Read the article

• How do I move a linked file on Unix?

  - by r3mbol

  I have a bunch of files in one directory and links to each one of those files in another directory. So ls -l looks something like this: lrwxrwxrwx 1 rembol rembol 89 Jan 25 10:00 copyright.txt -> /home/rembol/solr/target/deploy/data/core/copyright.txt lrwxrwxrwx 1 rembol rembol 92 Jan 25 10:00 jar-versions.xml -> /home/rembol/solr/target/deploy/data/core/jar-versions.xml lrwxrwxrwx 1 rembol rembol 85 Jan 25 10:00 lgpl.html -> /home/rembol/solr/target/deploy/data/core/lgpl.html lrwxrwxrwx 1 rembol rembol 79 Jan 25 10:00 lib -> /home/rembol/solr/target/deploy/data/core/lib lrwxrwxrwx 1 rembol rembol 87 Jan 25 10:00 readme.html -> /home/rembol/solr/target/deploy/data/core/readme.html drwxr-xr-x 3 rembol rembol 4096 Jan 25 10:00 server drwxr-xr-x 2 rembol rembol 4096 Jan 25 10:00 startup Now I want to move those linked files from /home/rembol/solr/target/deploy to /home/rembol/output/. If I do that my simply calling mv, links will break. I don't want to re-link each file separately, cause there are hundreds of them (they are generated automatically). Is there some clever way to move linked files, rather than writing a script that unlinks, moves and relinks recursively for each file in each subdirectory?

  Read the article

• Run GUI application via cronjob in Ubuntu?

  - by Christoffer

  Hi, I have a remote server running "Ubuntu 10.04 Desktop". From it I want to run a script that walks through a list of websites and captures screenshots of them. The script is working and thoroughly tested. When I SSH to the server with ssh -X user@ip-adress I can run my script by calling ./myscript.py and everything will work OK. I then modifed my crontab file and added... 59 17 * * * env DISPLAY=:0 /path/to/myscript.py ...as recommended by the Ubuntu WIKI. I can see in the /var/log/syslog that my cron job is started, but it doesn't capture any screenshots. When running env DISPLAY=:0 /path/to/myscript.py from the shell I get No protocol specified myscript.py: cannot connect to X server :0 If I ssh to the server without the -X option I only get the second row of the error: myscript.py: cannot connect to X server :0 What can I try now? More details I have run xhost +local: and checked the output of xhost to see that the option was set correctly. If I run ls /tmp/.X11-unix/ the output is X0 The server only has one screen. Thank you in advance!

  Read the article

• Openbsd init script for ssh VPN tunnel

  - by manthis

  I have a server hosting SSH tunnels and Openbsd 4.5 clients connecting to it. Things work just fine but I am in the need of automating the connection from the client to the server. So that if the client is accidentally rebooted, then the connection initiates unattended. So it should be as straight forward as to include the ssh connection in an init script. However I have miserably failed to do so by including it to /etc/rc.local, which is the file I usually do this sort of things in. Right now I am using autossh to also restart the connection if necessary and the script that I put on /etc/rc.local follows: #!/bin/sh # # Example script to start up tunnel with autossh. # # This script will tunnel 2200 from the remote host # to 22 on the local host. On remote host do: # ssh -p 2200 localhost # # $Id: autossh.host,v 1.6 2004/01/24 05:53:09 harding Exp $ # ID=root HOST=example.com #AUTOSSH_POLL=600 #AUTOSSH_PORT=20000 #AUTOSSH_GATETIME=30 #AUTOSSH_LOGFILE=$HOST.log #AUTOSSH_DEBUG=yes #AUTOSSH_PATH=/usr/local/bin/ssh export AUTOSSH_POLL AUTOSSH_LOGFILE AUTOSSH_DEBUG AUTOSSH_PATH AUTOSSH_GATETIME AUTOSSH_PORT autossh -2 -f -M 20000 ${ID}@${HOST} The script detaches just fine when run manually so I just include it on /etc/rc.local as echo -n 'starting local daemons:' if [ -x /usr/local/sbin/autossh.sh ]; then echo -n 'ssh tunnel' /usr/local/sbin/autossh.sh fi echo '.' I have also tried calling it from /etc/hostname.tun0 in case there may be issues with /etc/rc.local not being called at the right time when network connections are ready, so I would use: inet 10.254.254.2 255.255.255.252 10.254.254.1 !/usr/local/sbin/autossh.sh Your input is highly appreciated.

  Read the article

• Random server lag, no CPU/mem/pagefile usage

  - by Kev

  We have a fairly new server running Windows 2003 SP2, and the past few days we've noticed random slowdowns. When I'm logged into the server over remote desktop while this is happening, or if I'm physically sitting at the server logged in, suddenly everything becomes extremely laggy. Any UI element I try to interact with takes upwards of ten seconds to react, and then responds very slowly. Then a minute later everything is quite snappy again. During this, I have Task Manager minimized to the tray, and there's no CPU usage. I open it up right after this happens, and there's very little CPU usage on the graph, and no memory or pagefile usage above normal. (Normal being 1.5 GB free in the case of memory.) This is what I see logged into the server, and then users start calling saying things are slow, timing out, and failing--anything to do with our server. No events in the Event Viewer around the times this happens. The context I'm working in (last thing I clicked, etc.) seems different every time--different programs active, different combinations of programs open. Never anything particularly stressful (like adding an event entry to a Cobian Backup configuration, or editing text in TextPad, which has been exceptionally stable in my extensive usage of it.) I would've thought it was just the server, but a family member's home PC (entirely separate) running WinXPSP3 had the same thing happen to it last night a few times. Is this some new behaviour introduced by the latest Windows Updates? Either way, where do I even start to look when nothing seems to be chewing up resources?

  Read the article

• ssh Prompts For Password After Account Unlocked - Despite ssh key?

  - by user1011471

  Here's what happened: I set up ssh key so that user could ssh from A to B without a password. I got user's password wrong in some other context too many times, and user's account got locked out. (IT uses Active Directory here) IT unlocked the account. Concurrent to the unlocking, a script was running, calling something like ssh user@B some-health-check-command every 5 seconds or so -- which seemed to work fine before I caused user to get locked out in step 2. IT reports user reliably gets locked out a short time after each unlock attempt. I thought the ssh key would allow ssh user@B some-command as long as the account is not locked. But it behaves as if, when user gets unlocked, B suddenly asks for a password and since my command repeatedly runs without supplying a password, the account gets locked out after 5 attempts. Account cannot be accessed at this time. Please contact your system administrator. My questions are... Is that what's happening? Or: what's happening? More importantly: How can I reconfigure things such that my script doesn't cause problems? Can I accomplish what I want without having to install Expect? (I don't know if I have permission to do so) Other notes: Not using ssh-agent currently. The ssh command is running on our Jenkins master, a linux box. A and B are Mac OS X. user is managed in Active Directory and normally can sign into all three machines. Other than these things and the ssh key I set up, everything else has the default configuration as far as I know.

  Read the article

• File permission woes on an Ubuntu ec2 instance

  - by Pardoner

  I've set up an amazon ec2 instance and I'm have some file permission issues. I've created myself a new user and added myself to the following groups: adm:x:4:me,ubuntu sudo:x:27:me www-data:x:33:me,www-data ssh:x:108:me admin:x:111:me ubuntu:x:1000:www-data,me me:x:1001:me but when I cd /var/www I can't do simple commands without doing sudo. So I chown -R www-data:www-data /var/www to ensure that I'm in the owning group but I still have to type sudo for everything. If I sudo su www-data it works fine. Since I'm in the www-data group shouldn't I have the same privilages as www-data? One strange thing I'm noticing is that when I ls -l it list the owner but not the group names. Could this possibly be part of the issue? Is is posible for a directory to not be part of a group? drwxr-xr-x 4 www-data 4.0K Oct 24 16:39 . drwxr-xr-x 14 root 4.0K Oct 10 16:58 .. drwxrwxr-x 9 www-data 4.0K Oct 23 04:03 admin.mywebsite.com drwxrwxr-x 2 www-data 4.0K Oct 4 00:29 mywebsite.com drwxrwxr-x 9 www-data 4.0K Oct 23 04:03 staging.mywebsite.com Edit : It appears I had some alias messing with my ls command. By calling \ls -l I can see that all my files are in the correct group.

  Read the article

• K8NDRE motherboard in server fails to complete BIOS load with error 0078

  - by John

  K8NDRE motherboard with 4 sata drives, was running fine. Drives had raid-0 and raid-1 partitions, using mdadm. The onboard raid is disabled. Upon reformatting the drives, setting a new partition structure and new raid partitions, the bios fails to finish loading, with 0078 in the bottom right corner. Tried using completely new set of drives, and bios worked fine. Able to boot from a usb, format the drives, partition them, start raid, and then installed os. Reboot and received the same error from the bios, 0078. Works fine if I unplug the sata drives. Any thoughts? Physical inspection reveals no damage cables, connectors, or capacitors. Server was running happily for over a year, and this is the first problem it has had. Per Michael Hampton's answer: The drives, unjumpered and supporting sata III worked fine originally, and worked fine for formatting and having new partitions and raid installed on them. I did try jumpering one, with no change. If I put a brand new unformatted drive in, the motherboard recognizes it and I can proceed with formatting and installing. When I reboot, I get the 0078. I have 4 sata cables-the board supports 4 drives, so I tried each and no change. I am close to calling the motherboard done.

  Read the article

• How to autorun wpa_supplicant on Debian startup

  - by The Electric Muffin

  I'd like to run wpa_supplicant -D wext -i wlan0 -c /etc/wpa_supplicant.conf on Debian startup (runlevels 2-5). I found some vague instructions from a related question that said to put a script in /etc/init.d/ and then symlink to it from the apropriate /etc/rcRUNLEVEL.d/ directories. However, I noticed that there are already some files named "wpasupplicant" that probably run at startup: /etc/network/if-down.d/wpasupplicant /etc/network/if-post-down.d/wpasupplicant /etc/network/if-pre-up.d/wpasupplicant /etc/network/if-up.d/wpasupplicant They all are symlinks to the same script, /etc/wpa_supplicant/ifupdown.sh. It has a comment at the beginning saying it "[...] allows ifup(8), and ifdown(8) to manage wpa_supplicant(8) and wpa_cli(8) processes running in daemon mode." However, the closest it gets to calling wpa_supplicant itself is (in functions.sh): WPA_SUP_BIN="/sbin/wpa_supplicant" [snip] start-stop-daemon --start --oknodo $DAEMON_VERBOSITY \ --name $WPA_SUP_PNAME --startas $WPA_SUP_BIN --pidfile $WPA_SUP_PIDFILE \ -- $WPA_SUP_OPTIONS $WPA_SUP_CONF [snip] start-stop-daemon --stop --oknodo $DAEMON_VERBOSITY \ --exec $WPA_SUP_BIN --pidfile $WPA_SUP_PIDFILE Does that mean it's safe to make an init.d script for wpa_supplicant, and if so what would it look like? General info: Debian Squeeze (5.0) official wpasupplicant package (v0.6.10-2.1) The full contents of my system's functions.sh and ifupdown.sh are here (dependent, of course, on my system's uptime—it's a five-year-old laptop that greatly enjoys overheating): functions.sh ifupdown.sh

  Read the article

< Previous Page | 210 211 212 213 214 215 216 217 218 219 220 221  | Next Page >